WARNINGS - hubbellcdn · Hang fixture so that the Mounting Hub sets into the Top Plate and the hub flanges engage the inside of the top plate. ... 4. Insert rubber Bushing (E) between

SAVVANO™

LED Decorative Highbay

WARNINGS• This product contains chemicals known to the state of California to cause cancer,

birth defects and/or other reproductive harm.• Thoroughly wash hands after installing, handling, cleaning, or otherwise touching

this product.• Contact Hubbell Lighting, Inc. for information and direction before relamping or

replacing this light fixture.• Disconnect power before installing or servicing.• Install, operate and maintain to meet all applicable codes.• Protect all wiring connections with approved insulators (by others.)• Selected fixture voltage must match supply line voltage.

SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCEUpon receipt of this fixture, thoroughly inspect it for any damage. If any isfound, the carrier should be notified and held accountable.

http://www.hubbellindustrial.com/

http://www.hubbelllighting.com/

INSTALLATION INSTRUCTIONSFIXTURE RECEIVING:

• For shipping purposes, the fixture will come in multiple boxes.• The upper assembly will be packaged separately from the reflector assembly and, if optioned, the lens assembly.• See instructions on pages 3 & 4 for initial fixture assembly.

Hubbell Lighting, Inc. Doc. No. 93082515A subsidiary of Hubbell Incorporated Revision A701 Millennium Drive • Greenville, SC 29607 Page 2 Phone (864) 678-1000

Industrial Lighting

®

SAV–SAVVANO DECORATIVE FIXTUREINSTALLATION INSTRUCTIONS

OPTIONALEQUIPMENT

FIGURE 1FIXURE BOXING

UPPERASSEMBLY

REFLECTORASSEMBLY

LENS RING/HARDWARE

LENS

FIXTURE RECEIVING: • For shipping purposes, the fixture will come in multiple boxes. • The upper assembly will be packaged separately from the reflector

assembly and, if optioned, the lens assembly. • See instructions on pages 3 & 4 for initial fixture assembly.

REFLECTOR INSTALLATION:

MH / MM / ML MODELS (See Figure 2B)1. Reflector can be installed on the ground or while fixture is hanging. If installing on the ground,

it is best to place fixture upside down.2. Locate the four (4) threaded studs protruding from the bottom of the glass lens ring and align them

with the holes in the reflector collar.3. Insert the studs through the holes and thread on the provided hexagonal nut. Using a 5/16”

hex driver, tighten hexagonal nut to 10 in-lbs.

4. Reflector can be installed on the ground or while fixture is hanging. If installing on the ground, it is best of place fixture upside down.

5. Locate the four (4) threaded studs protruding from the bottom of the glass lens ring and align them with the holes in the reflector collar.

6. Insert the studs through the holes and install the provided hexagonal standoffs along with lock washers. Using a 1/4” hex driver, tighten the whexagonal standoffs to 10 in-lbs.

LX/ LH MODELS (See Figure 2A)

INSTALLATION INSTRUCTIONS

REFLECTORCOLLAR ASSEMBLY

REFLECTORCOLLAR ASSEMBLY

FIGURE 2BREFLECTOR COLLAR MOUNTING

MH / MM / ML

FIGURE 2AREFLECTOR COLLAR MOUNTING

LX / LH


Industrial Lighting

®

SAV-SAVVANO DECORATIVE FIXTUREINSTALLATION INSTRUCTIONS

HEXAGONALSTANDOFF4 PLACES

LOCKWASHER4 PLACES

THREADEDSTUD4 PLACES

HEXAGONALNUT4 PLACES

THREADEDSTUD4 PLACES

REFLECTOR INSTALLATION: MH / MM / ML MODELS (See Figure 2B) 1. Reflector can be installed on the ground or while fixture is hanging. If

installing on the ground, it is best to place fixture upside down. 2. Locate the four (4) threaded studs protruding from the bottom of the

glass lens ring and align them with the holes in the reflector collar. 3. Insert the studs through the holes and thread on the provided hexagonal

nut. Using a 5/16" hex driver, tighten hexagonal nut to 10 in-lbs. LX/ LH MODELS (See Figure 2A) 4. Reflector can be installed on the ground or while fixture is hanging. If

installing on the ground, it is best of place fixture upside down. 5. Locate the four (4) threaded studs protruding from the bottom of the

glass lens ring and align them with the holes in the reflector collar. 6. Insert the studs through the holes and install the provided hexagonal

standoffs along with lock washers. Using a 1/4" hex driver, tighten the hexagonal standoffs to 10 in-lbs.

LENS INSTALLATION (If Optioned):

1. Once the reflector has been mounted to the upper assembly, then the lens can be installed.2. Seat the lens into the bottom of the reflector.3. Orient Lens Mounting Ring such that short leg of the cross section is on top and install over the lip of the reflector

and lens. See Figure 3B.4. While manually holding the ring together, install screw through bracket holes and thread on hexagonal nut and

tighten till snug.



Industrial Lighting

®


LENS(OPTIONAL)

REFLECTOR

LENS MOUNTING RING

(OPTIONAL)

HEXAGONALNUT

SCREW

LENS MOUNTING RINGSEE NOTE 3

LENS

REFLECTOR

FIGURE 3ALENS MOUNTING

FIGURE 3B

LENS INSTALLATION (If Optioned): 1. Once the reflector has been mounted to the upper assembly,

then the lens can be installed. 2. Seat the lens into the bottom of the reflector 3. Orient Lens Mounting Ring such that short leg of the cross

section is on top and install over the lip of the reflector and lens. See Figure 3B.

4. While manually holding the ring together, install screw through bracket holes and thread on hexagonal nut and tighten till snug.

GENERAL INFORMATION

• All 12” (304.8 mm) minimum supply wire outside of conduit.• Fixture mounting hub conduit threads are 3/4-14 NPS.

PENDANT MOUNTING: (See Figures 4A & 4B)

1. Remove the Wire Access Cover and Mounting Hub Assembly from the fixture top by removing the (3) ¼” screws using a 3/8” Hex driver or flathead screwdriver. See Figure 4B.

2. The Mounting Hub Assembly should be installed on the already-hanging pendant conduit. See Figure 4A. The conduit and conduit lock nut should be securely fastened into the Mounting Hub at this time.

3. Thread the Set Screw into the Mounting Hub to lock into the Conduit using a 1/8” Allenhead driver. See Figure 4A.4. Loosely thread the Hub Lock Nut onto the Mounting Hub so that there is play between the Hub Plate and Mounting Hub.

See Figure 4A.5. Feed electrical supply wire through the conduit and out the bottom of the Mounting Hub, with 12” of extra wire

protruding from the bottom.6. Hang fixture so that the Mounting Hub sets into the Top Plate and the hub flanges engage the inside of the top plate.

Align holes in the Hub Plate with the holes in the Top Plate and insert and tighten the (2) ¼” screws to secure the position of the Hub. Tighten the Hub Lock Nut to the lock the plate and hub in place.


7. Pull the excess fixture and incoming wiring out through the Wire Access Cover hole and make the wiring connections. See appropriate WIRING SCHEMATIC for reference. Incoming power to be connected to the white and black wires. Ensure incoming wiring ground wire connected to fixture ground connector. See warnings above about wire connections. Dress wires as needed.

8. Once all wiring connections are made, place all wiring back inside wire box under the Access Cover and replace cover with (1) ¼” screw.

FIGURE 4APENDANT-MOUNTING HUB

ASSEMBLY

HUB LOCK NUT

HUB PLATE

MOUNTINGHUB

NOTE: SET SCREW TO BE THREADED BELOW OUTER

THREADS OF HUB FOR LOCKNUT TO BE ABLE TO THREAD

SCREW2x 1/4-20X.50

SCREW1/4-20X.50

MOUNTING HUBASSEMBLY

3/8" BUSHING

WIRE ACCESS COVER


Industrial Lighting

®


CONDUIT FORPENDENT HANGING

CONDUITLOCK NUT

FIGURE 4BPENDENT MOUNT

ASSEMBLY

FIXTURETOP PLATE

GENERAL INFORMATION • All 12” (304.8 mm) minimum supply wire outside of conduit. • Fixture mounting hub conduit threads are 3/4-14 NPS.

PENDANT MOUNTING: (See Figures 4A & 4B) 1. Remove the Wire Access Cover and Mounting Hub Assembly from

the fixture top by removing the (3) 1/4" screws using a 3/8" Hex driver or flathead screwdriver. See Figure 4B.

2. The Mounting Hub Assembly should be installed on the already-hanging pendant conduit. See Figure 4A. The conduit and conduit lock nut should be securely fastened into the Mounting Hub at this time.

3. Thread the Set Screw into the Mounting Hub to lock into the Conduit using a 1/8" Allenhead driver. See Figure 4A.

4. Loosely thread the Hub Lock Nut onto the Mounting Hub so that there is play between the Hub Plate and Mounting Hub. See Figure 4A

5. Feed electrical supply wire through the conduit and out the bottom of the Mounting Hub, with 12" of extra wire protruding from the bottom.

6. Hang fixture so that the Mounting Hub sets into the Top Plate and the hub flanges engage the inside of the top plate. Align holes in the Hub Plate with the holes in the Top Plate and insert and tighten the (2) 1/4" screws to secure the position of the Hub. Tighten the Hub Lock Nut to the lock the plate and hub in place.


8. Once all wiring connections are made, place all wiring back inside wire box under the Access Cover and replace cover with (1) 1/4" screw.

GENERAL INFORMATION

• All 12” (304.8 mm) minimum supply wire outside of conduit.• Fixture mounting hub conduit threads are 3/4-14 NPS.

PENDANT MOUNTING: (See Figures 4A & 4B)

1. Insert end of Cord (B) through Hook (A). Supply Cord is to be rated for a minimum of 90 degC 16/3 SOW-A.2. Remove Wire Access Cover after removing ¼” retaining screw.3. Loosen Hub Locknut and remove Hub and Hub Plate by removing (2) ¼” Screws.4. Insert rubber Bushing (E) between Washers (G) and place inside Mounting Hub. Place Cord Grip (C) with cone shape up

on top of washer (G).5. Thread Hook Lock Nut (D) to within 1/8” of the top of the hook threads.6. Insert Cord (B) through cord grip and washers and through the mounting hub.7. Thread the Hook into the ¾” NPS hole in the Mounting Hub down to the lock nut. Use pliers and wrench to tighten the

Hook Lock Nut (D) to lock the hook in place. CAUTION: Do not twist the Hook by using a screwdriver blade - too much force could break the Hook.

8. Using a 1/8” Allen head driver, tighten Set Screw in Mounting Hub to secure Hook from loosening.9. Place Hub into Top Plate of Housing so that the Hub flanges engage inside of the plate. Align holes in Hub Plate with

holes in Top Plate and insert and tighten ¼” screws to secure position of Hub. Tighten the Hub Locknut to lock Plate and Hub in place.


11. Once all wiring connections are made, place all wiring back inside wire box under the Access Cover and replace cover with (1) ¼” screw.

12. Attach Hook Closure Bracket onto end of Hook with screw provided. After fixture is hung, the Closure Bracket should be secured across the Hook opening to prevent disengagement.



Industrial Lighting

®


FIGURE 5AHOOK LOOP ASSEMBLY

FIGURE 5CHOOK LOOP ASSEMBLY

SCREW1/4-20X.50

WIRE ACCESS COVER

3/8" BUSHING

SCREW2x 1/4-20X.50

FIXTURETOP PLATE

HUB LOCK NUT

NOTE: SET SCREW TO BE THREADED BELOW OUTERTHREADS OF HUB FOR LOCKNUT TO BE ABLE TO THREAD

MOUNTINGHUB

HUB PLATE

A

D

HOOKCLOSUREBRACKET/SCREW

G

E

G

C

FIGURE 5BMOUNTING HUB

ASSEMBLY

B

GENERAL INFORMATION: • All 12” (304.8 mm) minimum supply wire outside of conduit. • Fixture mounting hub conduit threads are 3/4-14 NPS.

HOOK/LOOP MOUNTING: (See Figures 5A, 5B & 5C) 1. Insert end of Cord (B) through Hook (A). Supply Cord is to be rated for a minimum

of 90 degC 16/3 SOW-A. 2. Remove Wire Access Cover after removing 1/4" retaining screw 3. Loosen Hub Locknut and remove Hub and Hub Plate by removing (2) 1/4" Screws. 4. Insert rubber Bushing (E) between Washers (G) and place inside Mounting Hub.

Place Cord Grip (C) with cone shape up on top of washer (G). 5. Thread Hook Lock Nut (D) to within 1/8" of the top of the hook threads. 6. Insert Cord (B) through cord grip and washers and through the mounting hub. 7. Thread the Hook into the ¾” NPS hole in the Mounting Hub down to the lock nut.

Use pliers and wrench to tighten the Hook Lock Nut (D) to lock the hook in place. CAUTION: Do not twist the Hook by using a screwdriver blade - too much force could break the Hook.

8. Using a 1/8” Allenhead driver, tighten Set Screw in Mounting Hub to secure Hook from loosening.

9. Place Hub into Top Plate of Housing so that the Hub flanges engage inside of the plate. Align holes in Hub Plate with holes in Top Plate and insert and tighten 1/4" screws to secure position of Hub.Tighten the Hub Locknut to lock Plate and Hub in place.





Industrial Lighting

®


FIGURE 5AHOOK LOOP ASSEMBLY

FIGURE 5CHOOK LOOP ASSEMBLY

SCREW1/4-20X.50

WIRE ACCESS COVER

3/8" BUSHING

SCREW2x 1/4-20X.50

FIXTURETOP PLATE

HUB LOCK NUT

NOTE: SET SCREW TO BE THREADED BELOW OUTERTHREADS OF HUB FOR LOCKNUT TO BE ABLE TO THREAD

MOUNTINGHUB

HUB PLATE

A

D

HOOKCLOSUREBRACKET/SCREW

G

E

G

C

FIGURE 5BMOUNTING HUB

ASSEMBLY

B

GENERAL INFORMATION: • All 12” (304.8 mm) minimum supply wire outside of conduit. • Fixture mounting hub conduit threads are 3/4-14 NPS.

HOOK/LOOP MOUNTING: (See Figures 5A, 5B & 5C) 1. Insert end of Cord (B) through Hook (A). Supply Cord is to be rated for a minimum

of 90 degC 16/3 SOW-A. 2. Remove Wire Access Cover after removing 1/4" retaining screw 3. Loosen Hub Locknut and remove Hub and Hub Plate by removing (2) 1/4" Screws. 4. Insert rubber Bushing (E) between Washers (G) and place inside Mounting Hub.

Place Cord Grip (C) with cone shape up on top of washer (G). 5. Thread Hook Lock Nut (D) to within 1/8" of the top of the hook threads. 6. Insert Cord (B) through cord grip and washers and through the mounting hub. 7. Thread the Hook into the ¾” NPS hole in the Mounting Hub down to the lock nut.

Use pliers and wrench to tighten the Hook Lock Nut (D) to lock the hook in place. CAUTION: Do not twist the Hook by using a screwdriver blade - too much force could break the Hook.

8. Using a 1/8” Allenhead driver, tighten Set Screw in Mounting Hub to secure Hook from loosening.

9. Place Hub into Top Plate of Housing so that the Hub flanges engage inside of the plate. Align holes in Hub Plate with holes in Top Plate and insert and tighten 1/4" screws to secure position of Hub.Tighten the Hub Locknut to lock Plate and Hub in place.





WIRE GUARD INSTALLATION (If Optioned):

1. With the screws removed, spread the guard apart slightly and fit it around the lens ring already attached to the reflector.2. The guard should mount around the lens ring such that the ring fits between the top two circular rings.3. Insert the screws (2x) through the mounting holes and thread on the hexagonal kepis nuts (2x). Tighten the nuts till the

guard is clamped around the lens ring.


Industrial Lighting

®


33.5 26.5

MH / MM / ML MODELS

LX / LH MODELS

WIRE GUARD INSTALLATION (If Optioned): 1. With the screws removed, spread the guard apart slightly and fit it around the lens ring already attached to the reflector. 2. The guard should mount around the lens ring such that the ring fits between the top two circular rings. 3. Insert the screws (2x) through the mounting holes and thread on the hexagonal kepis nuts (2x). Tighten the nuts till the

guard is clamped around the lens ring.

WIRE GUARD

SCREW (2X)

KEPIS NUT (2X)FIGURE 6A

WIRE GUARD ASSEMBLY


OCCUPANCY SENSOR INSTALLATION (If Optioned):

NOTE: If a wire guard is supplied, the wire guard needs to be installed first (see Page 9, Fig. 7A) before installing sensor on thebracket. Position the guard so the sensor bracket fits through the top two rings of the guard.

1. Position the sensor box (without the tightening ring attached) on top of the bracket and place the threaded shaft through the hole in the bracket. Fasten the tightening ring onto the threads until sensor box is secure. See Fig. 7B.

2. Screw the sensor lens onto the threaded shaft until secure. See Fig. 7C.


Industrial Lighting

®


Mounting Bracket

FIGURE 7BSENSOR INSTALLATION

FIGURE 7CSENSOR INSTALLATION

Mounting Bracket

OCCUPANCY SENSOR INSTALLATION (If Optioned): NOTE: If a wireguard is supplied, the wire guard needs to be installed first (see Page 9, Fig. 7A) before installing sensor on the bracket. Position the guard so the sensor bracket fits through the top two rings of the guard. 1. Position the sensor box (without the tightening ring attached) on top of the bracket and place the threaded shaft through

the hole in the bracket. Fasten the tightening ring onto the threads until sensor box is secure. See Fig. 7B 2. Screw the sensor lens onto the threaded shaft until secure. See Fig. 7C.

WIRE GUARD ASSEMBLYW/ OCCUPANCY SENSOR

FIGURE 7AWIRE GUARD ASSEMBLYW/ OCCUPANCY SENSOR

LINE DRAWINGS

Drop (DLR) Lens Conical Drop (CDL) Lens P95/Clear (CLR)/No Lens

Drop (DLR) Lens Conical Drop (CDL) Lens

P95/Clear (CLR)/No Lens

31.0”

22.6”

28.4”30.1”

10.2”

25.0”

16.5”

23.1”

10.2”

21.8”

31.0”

22.6”

28.4”30.1”

10.2”

25.0”

16.5”

23.1”

10.2”

21.8”

22” Option

16” Option

WIRING DIAGRAMS

HIL_0355_SAV_IN_17 7/17

Hubb

ell L

ight

ing,

Inc.

Do

c. N

o. 9

3082

515

A su

bsid

iary

of H

ubbe

ll In

corp

orat

ed

R

evis

ion

A70

1 M

illen

nium

Driv

e • G

reen

ville

, SC

296

07

Pag

e 11

Pho

ne (8

64) 6

78-1

000

Indu

stria

l Lig

htin

g®

SAV-

SAVV

ANO

DEC

ORA

TIVE

FIX

TURE

INST

ALLA

TIO

N IN

STRU

CTIO

NS

ELEC

TRIC

AL D

IAG

RAM

LX /

LH M

OD

ELS

BLUE

BLACK

WHITE

BLACK

WHITELEADS

BLACKLEADS

BROWN

BLUE

BLUE

BROWN

OPTION - FUSING

BLACK

WHITE

TERMINAL ATTACHED TOWIRE BOX (INSIDE)

GREEN

GREEN

BLACK

RED

BLUE

WHITE

BLACK

RED

-W/O OCC. SENSOR: VIOLET AND GRAY LEADS TO BE ROUTED UPTHROUGHWIRE BOX WITH BLACK, WHITE, & GREEN LEADS EXITING FIXTURE

-W/ OCC. SENSOR: VIOLET AND GRAY LEADS TO BE ATTACHED TOAPPROPRIATE CONNECTORS ON SENSOR POWERPACK.

DIMMING OPTION

VIOLET LEADS GRAY LEADS

FROM DRIVER #2FROM DRIVER #1

FROM DRIVER #2FROM DRIVER #1

SEE TERMINATION OPTIONS

DRIVER #2

DRIVER #1

SURGESUPPRESSOR

BLACKLEADS

WHITELEADS

RED

RED

GREEN

GREEN

OPTION -OCCUPANCY SENSOR

POWERPACK



Industrial Lighting

®


BLUE

BLACK

WH

ITE

BLACKWH

ITELEAD

SBLAC

KLEAD

S

BROWN

BLUE

BLUE

BRO

WN

OPTIO

N - FUSING

BLACK

WH

ITE

TERM

INAL ATTAC

HED

TOW

IRE BO

X (INSID

E)

GR

EEN

GR

EEN

BLACK

RED

BLUE

WH

ITE

BLACK

RED

VIOLET AN

D G

RAY LEAD

TO BE

GR

OU

PED W

ITH BLAC

K, WH

ITE, &G

REEN

LEADS EXITIN

G FIXTU

RE

WH

EN D

IMM

ING

OPTIO

N IS U

TILIZED

DIMM

INGO

PTION

VIOLET LEAD

SG

RAY LEAD

S

FRO

M D

RIVER

#2FR

OM

DR

IVER #1

FRO

M D

RIVER

#2FR

OM

DR

IVER #1

SEE TERM

INATIO

N O

PTION

S

DRIVER #2

DRIVER #1

SUR

GE

SUPPR

ESSOR

BLACK

LEADS

WH

ITELEAD

S

RED

RED

GR

EEN

GREEN

ELECTRICAL DIAGRAMLX / LH MODELS

Hubb

ell L

ight

ing,

Inc.

Do

c. N

o. 9

3082

515

A su

bsid

iary

of H

ubbe

ll In

corp

orat

ed

R

evis

ion

A70

1 M

illen

nium

Driv

e • G

reen

ville

, SC

296

07

Pag

e 12

Pho

ne (8

64) 6

78-1

000

Indu

stria

l Lig

htin

g®

SAV-

SAVV

ANO

DEC

ORA

TIVE

FIX

TURE

INST

ALLA

TIO

N IN

STRU

CTIO

NS

ELEC

TRIC

AL D

IAG

RAM

MH

/ MM

/ M

L M

OD

ELS

BLACK

BLACK

WHITE

BLACK

WHITELEADS

BLACKLEADS

BLUE

BROWN

OPTION - FUSING

BLACK

WHITE

TERMINAL ATTACHED TOWIRE BOX (INSIDE)

GREEN

GREEN

RED

BLUE

WHITE

BLACK

RED

DIMMING OPTION

VIOLET LEADS GRAY LEADS

FROM DRIVER #1

FROM DRIVER #1

DRIVER #1

SURGESUPPRESSOR

BLACKLEADS

WHITELEADS

SEE TERMINATION OPTIONS

RED

GREEN


POWERPACK

-W/O OCC. SENSOR: VIOLET AND GRAY LEADS TO BE ROUTED UPTHROUGHWIRE BOX WITH BLACK, WHITE, & GREEN LEADS EXITING FIXTURE

-W/ OCC. SENSOR: VIOLET AND GRAY LEADS TO BE ATTACHED TOAPPROPRIATE CONNECTORS ON SENSOR POWERPACK.


Industrial Lighting

®


BLACK

BLACK

WH

ITE

BLACKWH

ITELEAD

SBLAC

KLEAD

S

BLUE

BRO

WN

OPTIO

N - FUSING

BLACK

WH

ITE

TERM

INAL ATTAC

HED

TOW

IRE BO

X (INSID

E)

GR

EEN

GR

EEN

RED

BLUE

WH

ITE

BLACK

RED

VIOLET AN

D G

RAY LEAD

TO BE

GR

OU

PED W

ITH BLAC

K, WH

ITE, &G

REEN

LEADS EXITIN

G FIXTU

RE

WH

EN D

IMM

ING

OPTIO

N IS U

TILIZED

DIMM

INGO

PTION

VIOLET LEAD

SG

RAY LEAD

S

FRO

M D

RIVER

#1

FRO

M D

RIVER

#1

DRIVER #1

SUR

GE

SUPPR

ESSOR

BLACK

LEADS

WH

ITELEAD

S

SEE TERM

INATIO

N O

PTION

S

RED

GR

EEN

ELECTRICAL DIAGRAMMH / MM / ML MODELS

http://www.hubbelllighting.com/

Documents

WARNINGS - hubbellcdn · Hang fixture so that the Mounting Hub sets into the Top Plate and the hub flanges engage the inside of the top plate. ... 4. Insert rubber Bushing (E) between