Wilson Tool - Press Brake Tooling Eurostyle - SM TECH - scule pentru abkanturi Amada Promecam style

Strength. Performance. Innovation.

EUROPEANSTYLE

PRESS BRAKE TOOL ING

www.wilsontool.ro

Distribuitor:

S.C. SM TECH SRL

Tehnologii şi soluţii pentru industria prelucrării tablelor

Tel: 0040-331-401599 Tel/Fax: 0040-231-515702 Tel Mob: 0040-745-528494 E-mail: [email protected]

www.sm-tech.ro www.wilsontool.ro

Vă stăm la dispoziţie cu plăcere cu orice informaţie sau ofertă pentru scule

Wilson Tool destinate maşinii d-voastră de ştantat CNC

Nitrex™ high endurance surface enhancement, exclusively from Wilson Tool, increases press brake tooling life by several times that of standard tooling. With a surface hardness of HRC-60 and a consistent 0.51mm of penetration below the surface of the tool, Nitrex™ adds lubricity to press brake tooling and lowers the coefficient of friction as the material slides over the shoulder of the V-opening on a die. Any Wilson Tool press brake punch or die can be enhanced with Nitrex™.

Most Wilson Tool press brake dies now come withNITREX™ as standard at no extra cost.

Extend The Life Of Your Tools With Nitrex.TM

Nitrex™ High Endurance Surface Enhancement Patent Number: 6,327,884 B1

Available for virtually any make and model of press brake, the Wilson Express Clamping System is uniquely designed to increase your productivity and reduce your operating costs.

• Load Punches in a Snap.Loading punches has never been easier. The Wilson Express Clamping system completely eliminates the need to slide punches in from the end of the machine. Simply place (415mm)long punches or individual pieces of sectionalized punchesunder the clamps and push them upward. The spring-loadedclamps capture the punch via the safety groove and hold it in place until the clamps are locked. To lock the clamps, simplypush the removable lever upward.

• Unload Punches Quickly and Easily.Again, Wilson has eliminated the need to slide punches to the end of the machine. Simply pull down the locking lever to unlock the clamp, or to remove smaller punch sections, pushing inward on the tops of the clamps opens the clamps and allows the operator to pull individual sections straight down. Clamps that are not in use can easily be removed from the punch holders by hand.

• No Special Tooling Required.Wilson Express Clamping Systems can be used with any standard European style press brake tooling with a safety groove. You canuse the same high quality Wilson tooling you currently own, without having to re-purchase the system for every tool you order.

• Fewer Maintenance Costs.Because the Wilson Express Clamping System is mechanicalrather than hydraulic, maintenance costs are virtually eliminated.And with no hydraulics there’s no risk of power failures causingclamps to release unexpectedly.

• Dual Clamping Available.A dual clamping feature is available on all Wilson ExpressClamping Systems for an additional cost. This added feature allows you to load punches with the safety groove facing forward or to the rear of the machine. Both front and rear clamps are opened and closed simultaneously when the locking lever is actuated.

For a free demonstration, or for more information on the Express Clamping System™, please contact your local Wilson Tool International® sales engineer or our sales desk on 0800 012 1475.

Z2 Style Press Brakes

Z1 Style Press Brakes

SAVE TIME AND MONEY WITH THEWILSON EXPRESS CLAMPING SYSTEM.TM

Terms and Conditions

UK Tel (Free): 0800 012 1475Ireland Tel (Free): 1-800 709 009

Fax (Free): 0800 012 1476Fax (Free): 1-800 535 538

email: [email protected]

Order Minimum order is £35.00.

Credit All orders are subject to the approval of our credit department. If you are a new account, please furnish us with a bank reference and three supplier references. A credit limit will be imposed on new accounts until credit has been established.

Payment Terms are net 30 days.

Cancellation In the event an order is cancelled, a charge will be made to coverlabour, materials and overheads.

Returned Material A handling charge of 25% is made on all standard parts returned

for credit. Written permission and shipping instructions must be obtained before the return of any material. Special tooling cannot be returned.

Claims All claims for shortages must be made within 3 days of the invoice date.

Prices Prices and specifications subject to change without prior notice. E & O E. All prices are exclusive of VAT.

Delivery Charge All orders are subject to a delivery charge.

Please call the sales desk for a delivery quotation.

Standard Punch & Die Lengths

1UK Tel (Free): 0800 012 1475Ireland Tel (Free): 1-800 709 009

Fax (Free): 0800 012 1476Fax (Free): 1-800 535 538


Standard Die Lengths

FEATURES:1. Most tools can be easily

loaded by a single operator.

2. Easy to store.

3. All sectionalised tools come pre-cut in nine different pieces.

4. Most sectionalised punches include two ear pieces (horns).

5. NITREX™(HRC-60) is available for every punch in the tooling line.

6. Special Tooling available. Please contact the sales desk.

SECTION WIDTHS:100mm LEFT EAR / 100mm RIGHT EAR / 10mm / 15mm / 20mm / 40mm / 50mm /200mm / 300mm

SECTION WIDTHS:100mm / 100mm / 10mm / 15mm / 20mm / 40mm / 50mm / 200mm / 300mm

Note: Special lengths are available at additional cost.

Note: Special lengths are available at additional cost.

(S)

(L)

(X)

415mm

835mm

835mm

(S)

(L)

(X)

415mm

835mm

835mm

FEATURES:1. Most tools can be easily

loaded by a single operator.

2. Easy to store.

3. All sectionalised tools come pre-cut in nine different pieces.

4. Most dies are NITREX enhanced (HRC-60) as standard.

5. Special Tooling available. Please contact the sales desk.

Standard Punch Lengths

Quick Reference Charts

2 UK Tel (Free): 0800 012 1475Ireland Tel (Free): 1-800 709 009

Fax (Free): 0800 012 1476Fax (Free): 1-800 535 538


LARGE RADIUS PUNCHESPAGE

LARGE 1V DIESPAGE

300


URETHANE PADSPAGE

URETHANE HOLDERSPAGE

1500

GOOSENECK PUNCHESWITH THIN TIPPAGE

QUICK CHANGE 2V DIESPAGE

2V DIE HOLDERSPAGE

DIE RAILPAGE

400

DEEP GOOSENECK PUNCHESPAGE

2V DIESPAGE

2V DIE HOLDERSPAGE

300

NARROW 1V DIEHOLDERSPAGE

NARROW 1V DIESPAGE

SASH PUNCHESPAGE

600

LARGE 1V DIESPAGE


1200

QUICK CHANGE 2V DIESPAGE

2V DIE HOLDERSPAGE

DIE RAILPAGE

NARROW PUNCHESPAGE

500

STANDARD PUNCHESPAGE 6

STANDARD PUNCHESWITH THIN TIPPAGE 7

NARROW PUNCHESPAGE 12

QUICK CHANGE 2V DIESPAGE 41-46




2V DIE HOLDERSPAGE 50

2V DIE RAILPAGE 50


2V DIE RAILPAGE 50


2V DIE RAILPAGE 50

LARGE RADIUS PUNCHESPAGE 20-21



LARGE 1V DIESPAGE 63-65

LARGE 1V DIESPAGE 63-65

URETHANE PADSPAGE 70


2V DIE RAILPAGE 50

SASH PUNCHESPAGE 13-14

GOOSENECK PUNCHESWITH THIN TIPPAGE 10

QUICK CHANGE1V DIESPAGE 51-56

QUICKCHANGE 1V DIE HOLDERSPAGE 60-61

URETHANE HOLDERSPAGE 69

2V DIESPAGE 46

GOOSENECK PUNCHESPAGE 8-11


90 DEGREE BENDING(0.4 - 3.4mm)

90 DEGREE BENDING WITHTHIN TIP GOOSENECK PUNCH

90 DEGREE BENDING WITH GOOSENECK PUNCH

90 DEGREE BENDING(SASH)

LARGE RADIUS BENDING(WITH URETHANE DIE)

LARGERADIUS BENDING

90 DEGREE BENDINGWITH NARROW PUNCH

90 DEGREE BENDINGWITH THIN TIP PUNCH


Quick Reference Charts


Fax (Free): 0800 012 1476Fax (Free): 1-800 535 538


3V HEMMING DIESPAGE

FLATTENING PUNCHESPAGE

1000

FLATTENING PUNCHESPAGE

FLATTENING DIESPAGE

1100

OFFSET TOOLSPAGE

2V DIE HOLDERSPAGE

DIE RAILPAGE

1800HEMMING(0.4 - 1.5mm)

HEMMING(0.4 - 3.0mm)

OFFSET BENDING(0.4 - 1.5mm)

FLATTENING PUNCHESPAGE 22

FLATTENING PUNCHESPAGE 22

RAIL STYLEOFFSET TOOLSPAGE 71


2V DIE RAILPAGE 50

FLATTENING DIESPAGE 66

3V HEMMING DIESPAGE 66

ACUTE ANGLE PUNCHESPAGE

ACUTE ANGLE LARGE1V DIESPAGE

1400


ACUTE ANGLE QUICKCHANGE 2V DIESPAGE

2V DIE RAILSPAGE

2V DIE HOLDERSPAGE

700

STANDARD PUNCH HOLDER(SUPPLIED WITH MACHINE)OR NARROW PUNCH HOLDERSPAGE

STACKING PUNCH HOLDEROR NARROW PUNCH HOLDERSPAGE

STANDARD PUNCHESPAGE

LOW PROFILE NARROW1V DIESPAGE

NARROW 1V DIE HOLDERSPAGE

1900

DEEP PUNCH HOLDERPAGE

STANDARD PUNCHESPAGE

1600


LARGE 1V DIESPAGE

900


HEMMING DIES

STEP 1

PAGE

STEP 2

800

ACUTE-ANGLE BENDING(2.7 - 4.9mm)

ACUTE-ANGLE BENDING(0.4 - 1.9mm) DEEP BOX BENDING DEEP PUNCH HOLDER


HEMMING (2 STAGE)(0.4 - 1.9mm)

ACUTE ANGLE PUNCHESPAGE 14-16 ACUTE ANGLE

PUNCHESPAGE 14-16

ACUTE ANGLEPUNCHES PAGE14-16

STEP 1

STEP 2

HEMMING DIESPAGE 67LARGE

1V DIESPAGE 63-65

DEEP PUNCH HOLDERPAGE 74STANDARD PUNCH HOLDER

(SUPPLIED WITH MACHINE)OR NARROW PUNCH HOLDERSPAGE 73

NARROW PUNCH HOLDERSPAGE 73

STANDARD PUNCHESPAGE 6-7

LOW PROFILE QUICK CHANGE 1VDIES PAGE 57

QUICK CHANGE 1VDIE HOLDERS PAGE 60-61

STANDARD PUNCHESPAGE 6

ACUTE ANGLE LARGE 1V DIESPAGE 62

ACUTE ANGLE PUNCHESPAGE 14-16

ACUTE ANGLE QUICKCHANGE 2V DIEPAGE 44

2V DIE RAILPAGE 50


Wilson Express Clamping SystemTM


Fax (Free): 0800 012 1476Fax (Free): 1-800 535 538


Cat. No. 8002, 8003, 43726, 6793, 6795, Express Clamp Torque Wrench Kit

Complete KitCasePivots

WrenchHex Tips

CAT. NO. COMPONENT PIECE PRICE KIT PRICE

800280034372667936795

Z1 Series with Wedge, 2 ClampZ1 Series with Wedge, 2 Clamp Interlocking


CAT. NO. DESCRIPTION PRICE

43817-243817i-2

4381743817i




43818-243818i-2

4381843818i

Wilson Express Clamping SystemTM


Fax (Free): 0800 012 1476Fax (Free): 1-800 535 538


For Wila beamed Press Brakes with Wedge


43819

For Conventional Press Brakes with Wedge


43815

Standard 88˚ & 90˚ Punches


Fax (Free): 0800 012 1476Fax (Free): 1-800 535 538


CAT. NO. Rmm

L835mm“H”

S415mm

XSECTIONALISED

E40102E40108E40115E40123E40130

0.20.81.52.33.0

66.966.766.466.065.7

MAX. TONper metre

(L & S)100100100100100

MAX. TONper metre

(X)4747474747

"H"

R

90

9mm

0

30mm

35mm

35mm

R 5mm

10mm

(Ear Piece)

R

880

30mm

"H"

9mm

R 5mm

10mm

35mm

35mm

(Ear Pirce)

Cat. No. E40102, E40108, E40115, E40123, E40130

Cat. No. E40002, E40006, E40008, E40015, E40023, E40030Standard 88˚ Punches

Standard 90˚ Punches

(Ear Piece)

(Ear Piece)

*Note: Punch tip modifications and punch relief available at additional cost. Contact the sales desk for prices and lead times.Nitrex™(HRC-60) available for every punch in the tooling range at additional cost.

*Note: Punch tip modifications and punch relief available at an additional cost. Contact the application sales desk for pricing and lead times.Nitrex™(HRC-60) available for every punch and die in the tooling line.

L835mm

S415mm

XSECTIONALISED

CAT. NO. Rmm

MAX. TONper metre

(L & S) “H”0.20.60.81.52.33.0

100100100100100100

66.966.466.666.366.065.7

MAX. TONper metre

(X)474747474747

E40002E40006E40008E40015E40023E40030

Standard 88˚ & 90˚ Punches With Thin Tip


Fax (Free): 0800 012 1476Fax (Free): 1-800 535 538


CAT. NO. Rmm

L835mm

S415mm

XSECTIONALISED

MAX. TONper metre

(L & S) “H”66.9

MAX. TONper metre

(X)0.2 20 10

CAT. NO. Rmm

L835mm

S415mm

XSECTIONALISED

E40202E40206

MAX. TONper metre

(L & S)

MAX. TONper metre

(X)

0.20.6

“H”66.966.4

2020

1010

10mm5mm

R 5mm

10mm

(Ear Piece)

"H"

R

90

4mm

0

30mm

10mm5mm

R 5mm

10mm

(Ear Piece)

Cat. No. E40202 and E40206Standard 90˚ Punches With Thin Tip

(Ear Piece)

Cat. No. E40212Standard 88˚ Punches With Thin Tip

(Ear Piece)

*Note: Punch tip modifications and punch relief available at an additional cost. Contact the application sales desk for pricing and lead times.Nitrex™(HRC-60) available for every punch and die in the tooling line.

"H"

R

88

4.02mm

0

30mm

E40212


88˚ Gooseneck Punches


Fax (Free): 0800 012 1476Fax (Free): 1-800 535 538


"H"

9mm

R

880

30mm

35mm

35mm

R 5mm

(Ear Piece)10mm

Cat No. E40402

9mm

880

R

"H"

30mm

10mm

R 5mm

35mm

35mm

(Ear Piece)

Cat. No. E40302 - E40630

Cat No. E40302





Fax (Free): 0800 012 1476Fax (Free): 1-800 535 538


Cat. No. E40302 - E40630


CAT. NO. Rmm

MAX. TONper metre

(L & S)L

835mm“H”S

415mmX

SECTIONALISED

E40302E40306E40308E40402E40406E40408E40415E40430E40602E40606E40608E40615E40630

0.20.60.80.20.60.81.53.00.20.60.81.53.0

50505050505050507070707070

MAX. TONper metre

(X)50505047474747474747474747

Cat No. E40602

(Ear Piece)

119.9119.4119.7104.9104.4104.6104.3103.789.989.489.689.388.7


88˚ & 90˚Gooseneck Punches With Thin Tip


Fax (Free): 0800 012 1476Fax (Free): 1-800 535 538


CAT. NO.R

mmL

835mmS

415mmX

SECTIONALISEDE40712E40718

0.20.8

5050

MAX. TONper metre

(L & S)

MAX. TONper metre

(X)3030

“H”89.989.7

(Ear Piece)

CAT. NO. Rmm

L835mm“H”

S415mm

XSECTIONALISED

0.20.60.8

505050

Cat. No. E40712 and E40718 90˚ Gooseneck Punches With Thin Tip

MAX. TONper metre

(L & S)

MAX. TONper metre

(X)303030

89.989.489.6

(Ear Piece)

Cat. No. E40702, E40706, E4070888˚ Gooseneck Punches With Thin Tip

E40702E40706E40708



90˚ & 85˚ Gooseneck Punches


Fax (Free): 0800 012 1476Fax (Free): 1-800 535 538


CAT. NO.R

mmL

835mmS

415mmX


4.86.35

100100

MAX. TONper metre

(L & S)

MAX. TONper metre

(X)4747

“H”105.0104.3

CAT. NO.R

mmL

835mmS

415mmX

SECTIONALISED

E40502 0.2 50

Cat. No. E40502 90˚ Gooseneck Punches

MAX. TONper metre

(L & S)

MAX. TONper metre

(X)47

Cat. No. E44540 and E4456085˚ Gooseneck Punches

(Ear Piece)

“H”

104.9

(Ear Piece)



88˚ & 90˚ Narrow Punches


Fax (Free): 0800 012 1476Fax (Free): 1-800 535 538


CAT. NO.R

mm

MAX. TONper metre

(X)L

835mmS

415mmX


0.20.6

5050

5050

“H”

95.094.5

MAX. TONper metre

(L & S)

CAT. NO. Rmm

L835mm

S415mm

XSECTIONALISED

E40902 0.2 50

90˚ Narrow PunchesCat. No. E40902

*Note: Sectionalised version does not include ear pieces (horns). Ear pieces (horns) available at additional cost.

Punch tip modifications and punch relief available at additional cost. Contact the sales desk for pricing and lead times.

Nitrex™(HRC-60) available for every punch in the tooling range at additional cost.

“H”95.0

MAX. TONper metre

*Note: Sectionalised version does not include ear pieces (horns). Ear pieces (horns) available at additional cost.

Punch tip modifications and punch relief available at additional cost. Contact the sales desk for pricing and lead times.

Nitrex™(HRC-60) available for every punch in the tooling range at additional cost.

Cat. No. E40802 and E4080688˚ Narrow Punches

88˚ Sash Punches


Fax (Free): 0800 012 1476Fax (Free): 1-800 535 538


CAT. NO.R

mmL

835mmS

415mmX

SECTIONALISEDE41002E41006 E41102E41106

0.20.60.20.6

30303030

Cat. No. E41002, E41006, E41102, E4110688˚ Sash Punches

MAX. TONper metre

(L & S)

MAX. TONper metre

(X)30303030

(Ear Piece)

(Ear Piece)

Cat No. E41102

“H”99.999.469.969.4

Cat No. E41002


90˚ Sash Punches & 30˚ Acute-Angle Punches


Fax (Free): 0800 012 1476Fax (Free): 1-800 535 538


"H" 20mm

R 8mm

12mm

20mm

300

R18mm(Ear Piece)

30mm

Cat. No. E41908 30˚ Acute-Angle Punches

(Ear Piece)

Rmm

L835mm

S415mm

XSECTIONALISED

0.2 30

Cat. No. E4120290˚ Sash Punches

E41202

CAT. NO. MAX. TONper metre

(L & S)

MAX. TONper metre

(X)

30

(Ear Piece)

“H”

69.9

Rmm

L835mm

S415mm

XSECTIONALISED

0.8 100E41908


(L & S)

MAX. TONper metre

(X)

20

“H”

104.0



30˚ Acute-Angle Punches


Fax (Free): 0800 012 1476Fax (Free): 1-800 535 538


Cat. No. E41315 and E4133030˚ Acute-Angle Punches

*Note: Sectionalised version does not include ear pieces (horns). Ear pieces (horns) available at additional cost. Punch tip modifications and punch relief available at additional cost. Contact the sales desk for prices and lead times. Nitrex™(HRC-60) available for every punch in the tooling range at additional cost.

*Note: Sectionalised version does not include ear pieces (horns). Ear pieces (horns) available at additional cost. Punch tip modifications and punch relief available at additional cost. Contact the sales desk for prices and lead times.Nitrex™(HRC-60) available for every punch in the tooling range at additional cost.

CAT. NO.R

mmL

835mm“H”S

415mmX


1.53.0

100100

MAX. TONper metre

(L & S)

MAX. TONper metre

(X)100100

102.097.7

"H"

18.24mm

R

300

30mm

Cat. No. E42610 30˚ Acute-Angle Punches

Rmm

L835mm

S415mm

XSECTIONALISED

0.8 100E42610


(L & S)

MAX. TONper metre

(X)

100

“H”

65.5

60˚ Acute-Angle Punches


Fax (Free): 0800 012 1476Fax (Free): 1-800 535 538


Cat. No. E41440 and E4146060˚ Acute-Angle Punches

CAT. NO.R

mmL

835mmS

415mmX

SECTIONALISED

E41440E41460

4.86.0

100100

MAX. TONper metre

(L & S) “H”

66.265.0

*Note: Sectionalised version does not include ear pieces (horns). Ear pieces (horns) available at additional cost. Punch tip modifications and punch relief available at additional cost. Contact the sales desk for pricesand lead times. Nitrex™(HRC-60) available for every punch in the tooling range at additional cost.

75˚ Punches


Fax (Free): 0800 012 1476Fax (Free): 1-800 535 538


Cat No. E44000

Cat. No. E44000 - E4403375° Punches

(Ear Piece)

(Ear Piece)

L835mm

S415mm

XSECTIONALISED

CAT. NO.R

mm

MAX. TONper metre

(L & S)

MAX. TONper metre

(X) “H”0.81.53.00.81.53.0

100100100505050

474747505050

67.667.266.2120.0119.5118.6

E44000E44001E44003E44030E44031E44033

Cat No. E44030


75˚ Punches


Fax (Free): 0800 012 1476Fax (Free): 1-800 535 538


Cat. No. E44010 - E4404075° Punches

75˚

10mm

"H"

R

30mm

Cat No. E44010 Cat No. E44040

Cat No. E44020

(Ear Piece)

*Note: Sectionalised version does not include ear pieces (horns). Ear pieces (horns) available at additional cost. (E44010 only)Punch tip modifications and punch relief available at additional cost. Contact the sales desk for prices and lead times.Nitrex™(HRC-60) available for every punch in the tooling range at additional cost.

Call for pricing and lead time.

*Nitrex™ is standard on Cat. No. E44040 only

L835mm

S415mm

XSECTIONALISED

CAT. NO.R

mm

MAX. TONper metre

(L & S)

MAX. TONper metre

(X) “H”0.8 1.5 3.00.81.53.00.8

70707050 505050

47474750505047

90.089.588.695.094.593.6160.0

E44020E44021E44023E44010E44011E44013

*E44040

Multi Radius Punches


Fax (Free): 0800 012 1476Fax (Free): 1-800 535 538


Punch BodiesCat. No. 46150 - 46152

Cat No. 46150 Cat No. 46151 Cat No. 46152


L830mm

L522mm

X (495mm)SECTIONALISED

461504615146152

100100100

N/AN/A

N/A N/A“H”679090

Punch Inserts


L835mm

L525mm

X (495mm)SECTIONALISED

4615346154461554615646157461584615946160461614616246163461644616546166461674616846169461704617146172

100100100100100100100100100100100100100100100100100100100100

N/AN/AN/AN/AN/AN/AN/AN/AN/AN/A



Radius“R”

33.54

4.55

5.56

6.57

7.58

1012.515

17.52025303540

Cat. No. 46153 - 46172

*Note: Sectionalised Radius inserts sold in sets only

‡

‡ Section widths: (46151 & 46152) 170,100, 50, 45, 40, 35, 30, 25

Large Radius Punches


Fax (Free): 0800 012 1476Fax (Free): 1-800 535 538


Cat. No. 41709 - 41719


"H"

30mm

R 9.5 mm

"H"

30mm

R 12.7 mm

"H"

30mm

15.9mm

"H"

30mm

R 19mm

Cat No. 41709 Cat No. 41712

Cat No. 41715 Cat No. 41719


L835mm

S415mm

XSECTIONALISED

41709417124171541719

100100100100

“H”83.089.087.091.0

*Note: Sectionalised version does not include ear pieces (horns). Ear pieces (horns) available at additional cost. Nitrex™(HRC-60) available for every punch in the tooling range at additional cost.Additional radii available, please contact the sales desk.



Fax (Free): 0800 012 1476Fax (Free): 1-800 535 538


Cat. No. 41722 and 41725


"H"

30mm

R 22.2mm

"H"

30mm

R 25.4mm

Cat No. 41722 Cat No. 41725


L835mm

S415mm

XSECTIONALISED

4172241725

100100

“H”94.096.0

*Note: Sectionalised version does not include ear pieces (horns). Ear pieces (horns) available at an additional cost. Nitrex™(HRC-60) available for every punch and die in the tooling line.Additional radii available, please contact our application sales desk.

Flattening Punches


Fax (Free): 0800 012 1476Fax (Free): 1-800 535 538



L835mm

S415mm

4152341630

100100

Cat. No. 41523 and 41630

"H"

30mm

40mm

23mm

"H"

30mm

14mm

12mm30mm

Cat No. 41523

Cat No. 41630

“H”

65.084.0

*Note: Nitrex™(HRC-60) available for every punch in the tooling range at additional cost.

Flattening Punches


Fax (Free): 0800 012 1476Fax (Free): 1-800 535 538


Flattening Punches

Bend Limit Graph

10

10

20

20

30

30

40

40

50

50

60

60

70

70

80

80

90

90

100

100

110

110

120

120

130

130

140

140

150

150

160

160

170

170

190

180

180

200

210

220

L

W

W

L

Z1 STYLE(DASHED LINES)

Z2 STYLE(SOLID LINES)

CATALOGUE NO. E40002, E40006, E40008, E40015, E40023, E40030,E40102, E40108, E40115, E40123, E40130

Bend Limit Graph

Bend Limit Graph


Fax (Free): 0800 012 1476Fax (Free): 1-800 535 538


10

10

20

20

30

30

40

40

50

50

60

60

70

70

80

80

90

90

100

100

110

110

120

120

130

130

140

140

150

150

160

160

170

170

190

180

180

200

210

220

L

W

W

L



CATALOGUE NO. E40202, E40206, E40212

Bend Limit Graph

Bend Limit Graph


Fax (Free): 0800 012 1476Fax (Free): 1-800 535 538


10

10

20

20

30

30

40

40

50

50

60

60

70

70

80

80

90

90

100

100

110

110

120

120

130

130

140

140

150

150

160

160

170

170

190

180

180

200

210

220



L

W

W

L

CATALOGUE NO. E40302, E40306, E40308

Bend Limit Graph

Bend Limit Graph


Fax (Free): 0800 012 1476Fax (Free): 1-800 535 538


10

10

20

20

30

30

40

40

50

50

60

60

70

70

80

80

90

90

100

100

110

110

120

120

130

130

140

140

150

150

160

160

170

170

190

180

180

200

210

220

W

W

L

L

W



CATALOGUE NO. E40402, E40406, E40408, E40415, E40430, E40502Bend Limit Graph

Bend Limit Graph


Fax (Free): 0800 012 1476Fax (Free): 1-800 535 538


Bend Limit GraphCATALOGUE NO. E40602, E40606, E40608, E40615, E40630

Bend Limit Graph


Fax (Free): 0800 012 1476Fax (Free): 1-800 535 538


CATALOGUE NO. E40702, E40706, E40708, E40712, E40718

Bend Limit Graph

Bend Limit Graph


Fax (Free): 0800 012 1476Fax (Free): 1-800 535 538


10

10

20

20

30

30

40

40

50

50

60

60

70

70

80

80

90

90

100

100

110

110

120

120

130

130

140

140

150

150

160

160

170

170

190

180

180

200

210

220



W

L

W

L

CATALOGUE NO. E44540, E44560

Bend Limit Graph

Bend Limit Graph


Fax (Free): 0800 012 1476Fax (Free): 1-800 535 538


10

10

20

20

30

30

40

40

50

50

60

60

70

70

80

80

90

90

100

100

110

110

120

120

130

130

140

140

150

150

160

160

170

170

190

180

180

200

210

220

L

W

L

W

CATALOGUE NO. E40802, E40806, E40902

Bend Limit Graph

Bend Limit Graph


Fax (Free): 0800 012 1476Fax (Free): 1-800 535 538


10

10

20

20

30

30

40

40

50

50

60

60

70

70

80

80

90

90

100

100

110

110

120

120

130

130

140

140

150

150

160

160

170

170

190

180

180

200

210

220

L

W

L

W


Bend Limit Graph

Bend Limit Graph


Fax (Free): 0800 012 1476Fax (Free): 1-800 535 538


10

10

20

20

30

30

40

40

50

50

60

60

70

70

80

80

90

90

100

100

110

110

120

120

130

130

140

140

150

150

160

160

170

170

190

180

180

200

210

220

L

W

L

W


Bend Limit Graph


Fax (Free): 0800 012 1476Fax (Free): 1-800 535 538



Bend Limit Graph

10

10

20

20

30

30

40

40

50

50

60

60

70

70

80

80

90

90

100

100

110

110

120

120

130

130

140

140

150

150

160

160

170

170

190

180

180

200

210

220 CATALOGUE NO. E41315, E41330, E41908

Bend Limit Graph

Bend Limit Graph


Fax (Free): 0800 012 1476Fax (Free): 1-800 535 538


10

10

20

20

30

30

40

40

50

50

60

60

70

70

80

80

90

90

100

100

110

110

120

120

130

130

140

140

150

150

160

160

170

170

190

180

180

200

210

220

L

W

W

L



CATALOGUE NO. E42610

Bend Limit Graph

Bend Limit Graph


Fax (Free): 0800 012 1476Fax (Free): 1-800 535 538


10

10

20

20

30

30

40

40

50

50

60

60

70

70

80

80

90

90

100

100

110

110

120

120

130

130

140

140

150

150

160

160

170

170

190

180

180

200

210

220

L

W

W



L

CATALOGUE NO. E44000, E44001, E44003

Bend Limit Graph

Bend Limit Graph


Fax (Free): 0800 012 1476Fax (Free): 1-800 535 538


10

10

20

20

30

30

40

40

50

50

60

60

70

70

80

80

90

90

100

100

110

110

120

120

130

130

140

140

150

150

160

160

170

170

190

180

180

200

210

220

L

W

W

L

W



CATALOGUE NO. E44030, E44031, E44033

Bend Limit Graph

Bend Limit Graph


Fax (Free): 0800 012 1476Fax (Free): 1-800 535 538


10

10

20

20

30

30

40

40

50

50

60

60

70

70

80

80

90

90

100

100

110

110

120

120

130

130

140

140

150

150

160

160

170

170

190

180

180

200

210

220

L

W

W

L



CATALOGUE NO. E44020, E44021, E44023

Bend Limit Graph

Bend Limit Graph


Fax (Free): 0800 012 1476Fax (Free): 1-800 535 538


10

10

20

20

30

30

40

40

50

50

60

60

70

70

80

80

90

90

100

100

110

110

120

120

130

130

140

140

150

150

160

160

170

170

190

180

180

200

210

220

L

W

W

L

W



CATALOGUE NO. E44010, E44011, E44013

Bend Limit Graph


Fax (Free): 0800 012 1476Fax (Free): 1-800 535 538


CATALOGUE NO. E44040

Bend Limit Graph


Fax (Free): 0800 012 1476Fax (Free): 1-800 535 538


Bend Limit Graph

10

10

20

20

30

30

40

40

50

50

60

60

70

70

80

80

90

90

100

100

110

110

120

120

130

130

140

140

150

150

160

160

170

170

190

180 190

180

200

210

220

230

240

L

W

W

L

CATALOGUE NO. 43002Bend Limit Graph

Bend Limit Graph

Quick Change 2V Dies


Fax (Free): 0800 012 1476Fax (Free): 1-800 535 538


Cat. No. E42000 - E42007Quick Change 2V Dies

( 4 )

4mm 7mm

5mm

13mm

15.05mm

34.5mm

6.5mm

13mm

R 0.4mm

46mm

3.5mm

( 2 ) ( 2 )

6mm 10mm

6.5mm

R 0.6mm

13mm

15.05mm

37mm

6.5mm

13mm

R 0.4mm

46mm

4.5mm

( 2 ) ( 2 )

8mm 12mm

7.5mm

R 0.8mm

13mm

15.05mm

39mm

6.5mm

13mm

R 0.5mm46mm

5.5mm

( 4 )

14mm 18mm

10.5mm8.5mm

13mm

15.05mm

45mm

13mm

6.5mm

R 0.5mm

46mm



90˚ 90˚

90˚ 90˚

*Note: V-opening modifications and die relief available at additional cost. Contact the sales desk for prices and lead times.Nitrex™(HRC-60) is standard on the dies on this page at no additional cost.



Fax (Free): 0800 012 1476Fax (Free): 1-800 535 538


Cat. No. E42004 - E42009Quick Change 2V Dies

( 4 )

4mm 7mm

5mm

13mm

15.05mm

34.5mm

6.5mm

13mm

R 0.4mm

46mm

3.5mm

( 2 ) ( 2 )

8mm 12mm

7.5mm

R 0.8mm

13mm

15.05mm

39mm

6.5mm

13mm

R 0.5mm46mm

5.5mm

Cat No. E42008

Cat No. E42009

88˚

88˚

6mm 10mm

6.5mm

R 0.6mm

13mm

15.05mm

37mm

6.5mm

13mm

R 0.4mm46mm

4.5mm

Cat No. E42007

88˚

( 4 )

14mm

8.5mm

18mm

10.5mm

13mm

15.05mm

45mm

6.5mm

13mm

R 0.5mm

46mm

Cat No. E42004

88˚




Fax (Free): 0800 012 1476Fax (Free): 1-800 535 538


( 4 )

12mm 20mm

12mm

13mm

15.05mm

45.5mm

6.5mm

13mm

R 0.5mm

46mm

7.5mm

Cat No. E42005

88˚

( 4 )

16mm 25mm

14.5mm

13mm

15.05mm

50mm6.5mm

13mm

R 0.8mm

46mm

9.5mm

Cat No. E42006

88˚

Cat. No. E42005 & E42006Quick Change 2V Dies


L835mm

S415mm

XSECTIONALISED

607080

100608070

1007070

Note: V-opening modifications and die relief available at additional cost. Contact the sales desk for prices and lead times.Nitrex™(HRC-60) is standard on the dies on this page at no additional cost.*Quick change 2V dies available in urethane. Please call our sales desk for pricing and lead time.

E42000*E42001*E42002E42003E42008E42007E42009

*E42004*E42005*E42006



Fax (Free): 0800 012 1476Fax (Free): 1-800 535 538



L835mm

S415mm

XSECTIONALISED

E42020*E42021

3030

Cat. No. E42010 - E42012

Quick Change 2V Dies With Large Shoulder Radii

Cat. No. E42020 and E42021Acute-Angle Quick Change 2V Dies

( 2 ) ( 2 )

6mm 10mm

8mm

R 2.5mm

13mm

15.05mm

40mm

13mm

R 1.5mm

6.5mm

46mm

6mm

( 4 )

6mm 10mm

15mm

R 1mm

13mm

15.05mm

50mm

6.5mm

13mm

50mm

9mm

( 4 )

8mm 12mm

18mm

R 1mm

13mm

15.05mm

58.5mm

13mm

6.5mm

50mm

14.5mm

( 2 ) ( 2 )

12mm 20mm

14mm

R 4mm

13mm

15.05mm

50mm

6.5mm

13mm

R 3mm

46mm

10mm

Cat No. E42011


Cat No. E42010


L835mm

S415mm

XSECTIONALISED

E42010E42012E42011

8080

100

90˚

30˚ 30˚

88˚6mm 10mm

8mm

R 2.5mm

13mm

15.05mm

40mm

6.5mm

13mm

R 1.5mm

46mm

6mm

Cat No. E42012

88˚


Note: V-opening modifications and die relief available at additional cost. Contact the sales desk for prices and lead times.Nitrex™(HRC-60) is standard on the dies on this page at no additional cost .*Quick change 2V dies available in urethane. Please call our sales desk for pricing and lead time.



Fax (Free): 0800 012 1476Fax (Free): 1-800 535 538


Cat. No. E44100 - E44103Quick Change 75° 2V Dies


L835mm

S415mm

XSECTIONALISED

E44100E44101E44102E44103

100100100100

10mm 16mm

11.2mm

R 3.5mm

13mm

15.05mm

45mm

6.5mm

13mm

R 2.5mm

46mm

7.7mm

6mm 20mm

13.5mm

R 4mm

13mm

15.05mm

44.7mm

6.5mm

13mm

R 1.5mm

46mm

5.2mm

Cat No. E44101Cat No. E44100

75˚ 75˚

10mm 22mm

14.7mm

R 4.5mm

13mm

15.05mm

48.5mm

R 2.5mm

13mm

6.5mm

46mm

7.7mm

12mm 25mm

16.7mm

R 5.5mm

13mm

15.05mm

51.7mm

6.5mm

13mm

R 3mm

46mm

9mm


75˚ 75˚


2V Dies (Old Style)


Fax (Free): 0800 012 1476Fax (Free): 1-800 535 538


Cat. No. E42030 - E420362V Dies (Old Style)

( 4 )

4mm

3.5mm

26mm

50mm

R 0.4mm

5mm

7mm

( 2 )( 2 )

6mm 10mm

6.5mm

R 0.6mm

50mm

R 0.4mm26mm

4.5 mm

( 2 ) ( 2 )

8mm

5.5mm

26mmR 0.5mm

50mm

R 0.8mm

7.5mm

12mm

( 4 )

14mm

8.5mm

26mm

50mm

R 0.5mm

10.5mm

18mm




L835mm

S415mm

E42030E42031E42032E42033E42034E42035E42036

60708010010010070

90˚ 90˚

90˚ 90˚

88˚

88˚

88˚Cat No. E42034 Cat No. E42035

Cat No. E42036

( 4 )

14mm

8.5mm

26mm

50mm

R 0.5mm

10.5mm

18mm

( 4 )

16mm

9.5mm

R 0.8mm26mm

50mm

25mm

14.5mm

( 4 )

12mm

7.5mm

26mmR 0.5mm

50mm

12mm

20mm

*Note: All mounting hardware is included.V-opening modifications and die relief available at additional cost. Contact the sales desk for prices and lead times.Nitrex™(HRC-60) is standard on the dies on this page at no additional cost.

2V Dies (Old Style)


Fax (Free): 0800 012 1476Fax (Free): 1-800 535 538


Cat. No. E42040 and E420412V Dies With Large Shoulder Radii (Old Style)

Cat. No. E42050 and E42051Sectionalised 2V Dies (Old Style)

( 2 ) ( 2 )

6mm

6mm

26mmR 1.5mm

55mm

R 2.5mm

10mm

10mm

( 2 )( 2 )

12mm 20mm

15mm

R 4mm

55mm

R 3mm26mm

10mm



L835mm

S415mm

E42040E42041

80100

( 4 )

4mm

3.5mm

46mm

6.5mm50mm

15.05mm

R 0.4mm

5mm

7mm

( 2 ) ( 2 )

6mm

4.5mm

46mm

R 0.4mm

6.5mm

50mm

15.05mm

R 0.6mm

6.5mm

10mm


90˚ 88˚

90˚ 90˚


XSECTIONALISED

E42050E42051

6070

*Note: All mounting hardware is included.V-opening modifications and die relief available at additional cost. Contact the sales desk for prices and lead times.Nitrex™(HRC-60) is standard on the dies on this page at no additional cost.


Sectionalised 2V Dies (Old Style)


Fax (Free): 0800 012 1476Fax (Free): 1-800 535 538


88˚

90˚ 90˚

88˚

88˚

Cat. No. E42052 - E42056Sectionalised 2V Dies (Old Style)


XSECTIONALISED

E42052E42053E42054E42055E42056

70100100100100

( 2 ) ( 2 )

8mm 12mm

7.5mm

R 0.8mm

15.05mm

50mm6.5mm

R 0.5mm

46mm

5.5mm

( 4 )

14mm 18mm

10.5mm8.5mm

R 0.5mm

15.05mm

50mm

6.5mm

46mm

( 4 )

14mm 18mm

10.5mm

R 0.5mm

15.05mm

50mm

6.5mm

46mm

8.5mm

( 4 )

20mm12mm

12mm

R 0.5mm

15.05mm

50mm6.5mm

46mm

7.5mm

( 4 )

16mm 25mm

14.5mm

R 0.8mm

15.05mm

50mm

6.5mm

46mm

9.5mm

Cat No. E42052


Cat No. E42056

Cat No. E42053


Sectionalised 2V Dies (Old Style)


Fax (Free): 0800 012 1476Fax (Free): 1-800 535 538



XSECTIONALISED

E42061E42062

7070

( 2 )( 2 )

6mm

4.5mm

R 0.4mm

16mm 6.5mm

50mm

15.05mm

R 0.6mm

6.5mm

10mm

Cat. No. E42070 and E42071Sectionalised 2V Dies With Large Shoulder Radii (Old Style)

Cat. No. E42061 and E42062Low Profile Sectionalised 2V Dies (Old Style)

(2) (2)

6mm

6mm

R 1.5mm

46mm

65mm

55mm

15.05mm

R 2.5mm

10mm

10mm

( 2 )( 2 )

12mm

10mm

20mm

15mm

R 4mm

15.05mm

55mm

6.5mm

R 3mm

46mm


( 2 )( 2 )

8mm 12mm

7.5mm

R 0.8mm

15.05mm

50mm

6.5mm16mm

R 0.5mm

5.5mm



XSECTIONALISED

E42070E42071

80100

90˚

90˚ 90˚

88˚



2V Die Rail And Clamp, Stacking Rails & 2V Die Holders


Fax (Free): 0800 012 1476Fax (Free): 1-800 535 538


END VIEW

Cat No. 43553

39mm

60mm

45mm

60mm

15mm

["X"]

50mm

15mm7mm

Cat. No. 42090 and 435532V Die Rail And Clamp

Cat. No. 43021, 43022, 43021LAT, 43021SAT, 43022LAT, 43022SAT2V Die Holders

Cat. No. 42091 and 42092Stacking Rails

CAT. NO. L835mm

S415mm

4355342090

FRONT VIEW

Cat No. 43021 Cat No. 43022

*Note: All mounting hardware is included.

15mm

15mm

50mm10mm

Cat No. 42090

Cat No. 42092

CAT. NO. L835mm

S415mm

4302143022

43021 LAT43021 SAT43022 LAT43022 SAT

N/A

N/A

N/A

N/A

CAT. NO. HEIGHTRANGE

LT835mm

ST415mm

420914209242093

X= .575 - 1.250X=1.251 - 2.000X=2.001 - 2.750

60mm

[ "X" ]

39mm

60mm

[ "X" ]

45mm

XTSECTIONALISED

Cat No. 43021 LAT43021 SAT

Cat No. 43022 LAT43022 SAT

60mm Quick Change 1V Dies


Fax (Free): 0800 012 1476Fax (Free): 1-800 535 538


Cat No. E42130

30˚

Cat. No. E42130 - E42133

Cat No. E42131

30˚


L835mm

XSECTIONALISED

E42130E42131E42132E42133

100100100100

S415mm


Cat No. E42132

30˚

Cat No. E42133

30˚

*Note: Quick Change 1V Dies require die holder No. 46220/46221.

V-opening modifications and die relief available at additional cost. Contact the sales desk for prices and lead times.

Nitrex™(HRC-60) is standard on the dies on this page at no additional cost.



Fax (Free): 0800 012 1476Fax (Free): 1-800 535 538


Cat No. E42160 Cat No. E42161 Cat No. E42162

60˚ 60˚ 60˚

Cat. No. E42160 - E42166


60˚ 60˚ 60˚

Cat No. E42166

60˚


L835mm

XSECTIONALISED

E42160E42161E42162E42163E42164E42165E42166

100100100100100100100

S415mm



V-opening modifications and die reliefavailable at additional cost. Contact the sales desk for prices and lead times.

Nitrex™(HRC-60) is standard on thedies on this page at no additionalcost.



Fax (Free): 0800 012 1476Fax (Free): 1-800 535 538



88˚ 88˚ 88˚

Cat. No. E42821 - E42829


88˚ 88˚ 88˚


88˚ 88˚ 88˚


L835mm

XSECTIONALISED

E42821E42822E42823E42824E42825E42826E42827E42828E42829

100100100100100100100100100

S415mm



V-opening modifications and die reliefavailable at additional cost. Contact the sales desk for prices and lead times.

Nitrex™(HRC-60) is standard on thedies on this page at no additionalcost.



Fax (Free): 0800 012 1476Fax (Free): 1-800 535 538



90˚ 90˚ 90˚

Cat. No. E42801 - E42805


90˚ 90˚


L835mm

XSECTIONALISED

E42801E42802E42803E42804E42805

100100100100100

S415mm


*Note: Quick Change 1V Dies require die holder No. 46220/46221. V-opening modifications and die relief available at additional cost. Contact the sales desk for prices and lead times.Nitrex™(HRC-60) is standard on the dies on this page at no additional cost.



Fax (Free): 0800 012 1476Fax (Free): 1-800 535 538


Cat. No. E42100 - E42122

( 2 )

8mm

R 1.5mm

14mm

83.5mm

( 2 )R 2.5mm

17mm

14mm

83.5mm

12mm

( 2 )

10mm

R 2mm

14mm83.5mm


Cat No. E42102

90˚ Quick Change 1V Dies

90˚

90˚

90˚

( 2 )

6mm

R 1.5mm

83.5mm

14mm

Cat No. E42100

90˚

*Note: Quick Change 1V Dies require die holder No. 43030/43530. V-opening modifications and die relief available at additional cost. Contact the sales desk for prices and lead times.Nitrex™(HRC-60) is standard on the dies on this page at no additional cost.



Fax (Free): 0800 012 1476Fax (Free): 1-800 535 538


Cat. No. E42100 - E42122

( 2 )

8mm

R 1.5mm

14mm

83.5mm

( 2 )

12mm

R 2.5mm

17mm83.5mm

14mm

( 2 )

14mm

R 2.5mm

18mm83.5mm

14mm

( 2 )

10mm

R 2mm

14mm83.5mm


L835mm

XSECTIONALISED

E42100E42101E42102E42103E42104E42105E42120E42121E42122

100100100100100100100100100



88˚ Quick Change 1V Dies

88˚ 88˚

88˚ 88˚

*Note: Quick Change 1V Dies require die holder No. 43030. V-opening modifications and die relief available at additional cost. Contact the sales desk for prices and lead times.Nitrex™(HRC-60) is standard on the dies on this page at no additional cost.

S415mm

( 2 )

6mm

R 1.5mm

83.5mm

14mm

Cat No. E42120

88˚

Low Profile Quick Change 1V Dies


Fax (Free): 0800 012 1476Fax (Free): 1-800 535 538



S415mm

XSECTIONALISED

E42110E42111E42112E42114

100100100100

90˚ 90˚ 88˚90˚

Cat. No. E42110 - E42114Low Profile Quick Change 1V Dies

( 2 )

6mm

30mmR 1.5mm

14mm

( 2 )

8mm

R 1.5mm

14mm

30mm

( 2 )

10mm

30mm R 2mm

14mm

( 2 )

12mm

30mm 17mm

R 2.5mm

14mm

Cat No. E42110 Cat No. E42111 Cat No. E42112 Cat No. E42114

*Note: Low Profile Quick Change 1V Dies require die holder No.43030.Low Profile Quick Change 1V Dies No.E42110 and No.E42112 are available in 88˚ versions at additional cost.V-opening modifications and die relief available at additional cost. Contact the sales desk for prices and lead times.Nitrex™(HRC-60) is standard on the dies on this page at no additional cost.Available in L (long) at additional cost.

Acute-Angle Quick Change 1V Dies


Fax (Free): 0800 012 1476Fax (Free): 1-800 535 538


Cat. No. E42200 - E42205


L835mm

XSECTIONALISED

E42200E42201E42202E42203E42204E42205

100100100100100100

Cat No. E42200




30˚ 30˚ 30˚

30˚ 30˚ 30˚


S415mm

Quick Change 75° 1V Dies


Fax (Free): 0800 012 1476Fax (Free): 1-800 535 538


Cat. No. E44200 - E44207Quick Change 75° 1V Dies

Cat No. E44200

75˚Cat No. E44201

75˚Cat No. E44202

75˚Cat No. E44203

75˚


L835mm

XSECTIONALISED

E44200E44201E44202E44203E44204E44205E44206E44207

100100100100100100100100

3mm

R 0.4mm

14mm83.5mm

6mm

R 1.5mm

14mm83.5mm

10mm

R 2.5mm

17mm

14mm

83.5mm

12mm

R 3mm

19mm

14mm

83.5mm

Cat No. E44204

75˚Cat No. E44205

75˚Cat No. E44206

75˚Cat No. E44207

75˚16mm

R 3.5mm

24mm

14mm

83.5mm

20mm

R 4mm

28mm

14mm

83.5mm

22mm

R 4.5mm

32mm

14mm

83.5mm

25mm

R 5.5mm

36mm

14mm

83.5mm


S415mm

Quick Change 1V Die Holders


Fax (Free): 0800 012 1476Fax (Free): 1-800 535 538


For 60mm High Quick Change 1V Dies

Cat No. 46220


L835mm

4622046221

100100

S415mm

“H”

61.561.5

Cat. No. 46220 and 46221

Cat No. 46221

Quick Change 1V Die Holders And Wedge Blocks


Fax (Free): 0800 012 1476Fax (Free): 1-800 535 538


CAT. NO. S415mm

L835mm

43030E4353043559

Cat. No. 43030, 43530 and 43559

Quick Change 1V Die Holder And Wedge Block

SIDE VIEW

TOP VIEW

30mm

14.1mm

22mm

60mm

28mm

Cat No. 43030

Cat No. 43559

*Note: Available with die tang. Contact the sales deskfor prices and lead times.

For 83.5mm High Quick Change 1V Dies

(14.1).555

(30)1.181

(28)1.102

(60)2.362

(22).066

Cat No. E43530

Acute-Angle Large 1V Dies


Fax (Free): 0800 012 1476Fax (Free): 1-800 535 538


Cat. No. E42300 - E42304Acute-Angle Large 1V Dies

( 2 )

18mm

60mm

R 3mm

60mm

(2)

25mm

R 4mm

60mm

65mm



L835mm

S415mm

E42300E42301E42302E42303E42304

8060407070

30˚

45˚

45˚

45˚

30˚

( 2 )

60mm

32mm

R 5mm

60mm

( 2 )

40mm

R 5mm

60mm

80mm

80mm

( 2 )

50mm

R 6mm

60mm

95mm

95mm

Cat No. E42302

Cat No. E42304

Cat No. E42303

*Note: Acute-Angle Large 1V Dies may require die holder No.43040.Check height against machine stroke prior to ordering.V-opening modifications and die relief available at additional cost. Contact the sales desk for prices and lead times.Nitrex™(HRC-60) is available for these dies at an additional cost.

Large 1V Dies


Fax (Free): 0800 012 1476Fax (Free): 1-800 535 538


85˚

85˚ 85˚

85˚

Cat. No. E42400 - E42403Large 1V Dies

( 2 )

32mm

R 4mm

60mm

60mm

( 2 )

40mm

R 4mm

60mm

60mm

( 2 )

50mm

60mm

R 4mm

60mm

( 2 )

63mm

R 5mm

60mm

80mm

75mm




L835mm

S415mm

E42400E42401E42402E42403

100100100100

*Note: Large 1V Dies may require die holder No.43040.Check height against machine stroke prior to ordering.V-opening modifications and die relief available at additional cost. Contact the sales desk for prices and lead times.Nitrex™(HRC-60) is available for these dies at an additional cost.

Large 1V Dies


Fax (Free): 0800 012 1476Fax (Free): 1-800 535 538


Cat. No. E42404 and E42405

( 2 )

80mm

R 6mm

60mm

95mm

95mm

( 2 )

100mm

R 7mm

60mm

120mm

110mm

Cat No. E42405

Cat No. E42404

Large 1V Dies

85˚

85˚

*Note: V-opening modifications and die relief available at additional cost. Contact the sales desk for prices and lead times.Nitrex™(HRC-60) is available for these dies at an additional cost.

Large 1V Dies


Fax (Free): 0800 012 1476Fax (Free): 1-800 535 538


Cat No. E42406

Cat. No. E42406Large 1V Dies

80˚

Cat. No. 43040Large 1V Die Holder

50mm

60mm

CAT. NO. L835mm

S415mm

43040


L835mm

S415mm

100100100

E42404E42405E42406

*Note: Large 1V Dies may require die holder No.43040. Check height against machine stroke prior to ordering.Please check width of lower beam of press brake prior to ordering die No.42406.V-opening modifications and die relief available at additionalcost. Contact the sales desk for prices and lead times.Nitrex™(HRC-60) is available for this die at an additional cost.

( 2 )

125mm

R 9mm

90mm

154mm

R 123mm


Fax (Free): 0800 012 1476Fax (Free): 1-800 535 538


104.4mm

79mm

96mm

60mm


L835mm

S415mm

S415mm

42310 100


L835mm

S415mm

42311 100

Cat. No. 42310 3V Hemming Die

Cat. No. 42311 Flattening Die

( 2 ) ( 2 )

( 2 )

6mm

12mm

R 1mm

60mm

R 1mm

60mm

10mm

R 1mm

30˚

Cat. No. 42312 Quick Change Rail Style Flattening Die

*Note: Nitrex™(HRC-60) is standard on the dies on this page at no additional cost.


42312 100

*Note: Designed to run with standard 2V Quick Change die system.Custom heights available for stage bending. Contact the sales desk for pricing and lead times.Nitrex™(HRC-60) is standard on the dies on this page at no additional cost.


XSECTIONALISED

Call for pricing and lead time

L835mm

50mm

15.05mm

50.0mm

14.5mm

Cat No. 42312

Cat No. 42310

Cat No. 42311

Quick Change Rail Style Flattening Die,3V Hemming Die & Flattening Die


Fax (Free): 0800 012 1476Fax (Free): 1-800 535 538


Hemming Dies

Cat. No. 42601 - 42603 and 43522 - 43524Hemming Dies

(2)

6mm

16mm

14mm

23mm

60mm

116.5mm

R 1mm

Cat No. E42601

(2)

16mm

14mm

23mm

60mm

116.5mm

R 1mm

8mm

(2)

16mm

22mm

31mm

60mm

124.5mm

R 1mm

10mm

Cat No. E42602

Cat No. E42603


L835mm

S415mm

676767676767

MAX.MATERIAL

C.R.S.

1.0mm1.5mm2.0mm1.0mm1.5mm2.0mm

E42601E42602E42603E43522E43523E43524

Cat No. E43524


6mm

16mm

14mm

23mm

8mm

16mm

14mm

23mm

10mm

16mm

22mm31mm

Replacement V-Blocks for Wilson Hemming Dies


2 Stage Hemming Set


Fax (Free): 0800 012 1476Fax (Free): 1-800 535 538


2 Stage Process - Note: 1.6mm Maximum Material

Stage 1 Stage 2

CAT. NO. L835mm

XSECTIONALISED

S415mm

E41909E43595

Max Tonper metre= 67

Max Tonper metre= 100

Punch OnlyCat. No. E41909

Die OnlyCat. No. E43595

N/A

Urethane Holders


Fax (Free): 0800 012 1476Fax (Free): 1-800 535 538


Cat. No. 42501 - 42504Urethane Holders

30mm

43mm

60mm

50mm

100mm

60mm

91mm

80mm

83mm

60mm

120mm

110mm

60mm

150mm

108mm

Cat No. 42501

Cat No. 42504

Cat No. 42502

Cat No. 42503

CAT. NO. L835mm

S415mm

42501425024250342504

*Note: All urethane die holders are machined from6061-T6 aluminium. Urethane holders may require die holder #43040.Check height against machine stroke prior to ordering.

Urethane Pads


Fax (Free): 0800 012 1476Fax (Free): 1-800 535 538


Cat. No. 42511 - 42524Urethane Pads

30mm

25mm

30mm

80mm

50mm

50mm

Cat No. 42511 and 42521 Cat No. 42512 and 42522

Cat No. 42513 and 42523

CAT. NO. SHOREHARDNESS

L835mm

S415mm

4251142521425124252242513425234251442524

80A / Red90A / Blue80A / Red90A / Blue80A / Red90A / Blue80A / Red90A / Blue

Cat No. 42514 and 42524

45mm

110mm

Rail Style Offset Tools


Fax (Free): 0800 012 1476Fax (Free): 1-800 535 538


Cat. No. 43100 - 43106Rail Style Offset Tools

94mm

3.18mm

92.88mm

4.8mm 6.4mm

91.76mm

90.65mm

7.9mm 9.52mm

89.51mm 88.39mm

11.1mm

87.27mm

12.7mm


MAX.MATERIAL

C.R.4.

L835mm

43100431014310243103431044310543106

100100100100100100100

1.0mm1.0mm1.0mm1.5mm1.5mm1.5mm1.5mm

*Note: *Dimensions are for shut height requirements less material thickness. †Offset height may vary as much as +- 0.5mm after bending. All angles will be obtuse.Special offset sizes are available at additional cost.Nitrex™(HRC-60) is standard on the dies on this page at no additional cost.Quick change offset tools are available at additional cost.



Cat No. 43106

** *

*

*

* *

S415mm

† †

††

†

XSECTIONALISED


Fax (Free): 0800 012 1476Fax (Free): 1-800 535 538


CAT. NO.

CAT. No. PRICE

42702

*Note: Quick Change BackGauge Stopper Padsare for Amada StyleBack Gauges.

(Includes Cat. No. 42704 & No. 42705 stabilizers.)

Side Gauge and Protractor Assembly with CaseCat No. 42702

Cat. No. 42702, 42704, 42705Side Gauge and Protractor Assembly & Accessories

CAT. NO. PRICE

42703

Cat. No. 42703, 42707, 42708, 42709, 42712

Quick Change Back Gauge Stopper Plate/Pads

42704

42705

Adjustable Back Gauge Stopper PlateCat No. 42703

Single Point PadCat No. 42709

Reworkable PadCat No. 42712

Sheet Support PadCat No. 42708

1V Die StabilizerCat No. 42704

2V Die StabilizerCat No. 42705

PRICE

4270842709

42712

42707

Replaces Original PadCat No. 42707

Accessories


Fax (Free): 0800 012 1476Fax (Free): 1-800 535 538


*Note: Intended for use with Quick Change, 2V, Sectionalised 2V, and Quick Change 1V Dies.

CAT. NO. PRICE

42701

Cat. No. 42701Side Gauge

Accessories

Urethane Rolls For Mark-Free Bending

Cat. No. 42530 and 42531Urethane Rolls

30M

*Note: Urethane dies are also available for mark-free bending.Contact the sales desk for prices and lead times.

DIMENSIONSCAT. NO.

4253042531

0.4 x 1520.8 x 152

Squaring Arm

The Wilson Squaring Arm from Wilson Tool Press Brake is a flexible tool enabling you to get more parts through your Press Brake with a high accuracy.

• Available for RH or LH loading of parts

• Simple and quick to fit

• Can be used for bending parts at an angle

• Makes bending small parts much easier and safer

• Can be used as end stop for Z bends

CAT. NO. PRICE

R/H 47000L/H 47001

Cat. No. 47000, 47001

Narrow Punch Holders


Fax (Free): 0800 012 1476Fax (Free): 1-800 535 538


Cat. No. 43000 and 43001


130mm

100mm

7mm

50mm

150mm

120mm

21mm

50mm

Cat No. 43000

Cat No. 43001

CAT. NO. 50mm

4300043001

Deep Punch Holder


Fax (Free): 0800 012 1476Fax (Free): 1-800 535 538


250mm

21mm

220mm

Cat. No. 43002

Deep Punch Holder

Cat No. 43002

CAT. NO.

43002150mm

MAX. TONper metre

50

Note: Punch holder No.43002 is available for Z2style upper beams (rams) only.Please consult the sales desk prior to ordering.

European Style Manual Clamps Features and Benefits


Fax (Free): 0800 012 1476Fax (Free): 1-800 535 538


NEW - Nitrex TM Enhanced Manual Clamps from Wilson Tool

Wilson Tool is pleased to introduce a range of enhanced Z1 and Z2manual clamps for European Style Press Brakes.

Benefits:

• The ability to use clamps hard up against one another for support over the full length of the form (interlocking wedge models only)

• A more cost-effective alternative for those not using the Wilson Express Clamping System

• High quality products and great value for money. Our new lower pricing reflects how our Lean manufacturing processes can directly benefit our customers

• The Clamps are durable, scratch and corrosion-resistant

• The location faces do not damage the tools due to the lubricity of the NitrexTM

surface treatment which is provided as standard

• The ability to upgrade single clamps to dual clamps (interlocking and non-interlocking) by using the handy upgrade kits

• Fast and efficient delivery as these items are in stock

European Style Manual Clamps - Z1 Range


Fax (Free): 0800 012 1476Fax (Free): 1-800 535 538


Z1 Punch Holder with Wedge, Single Clamp

CAT. NO. DESCRIPTION

E437004370930160

E43519F43504E43505E4370243499E43708

Z1 Wedge Face Plate5/16” Hardened Washer

M8 x 30 Lg S.H.C.S.Safety Clamp

M10 x 35mm Lg S.H.C.S.14.3mmO/ x 22.2mm Lg SpringZ1 Wedge Punch Holder Body

M8 x 25mm Lg S.H.C.S.Z1 Wedge

PRICENo.

123456789

111122121


E437004370930160

E43519F43504E43505E4370243499

E43708i




M8 x 25mm Lg S.H.C.S.Z1 Inter-Locking Wedge

PRICE No.

123456789

111122121

Cat. No. 43901i Z1 Punch Holder with Interlocking Wedge, Single Clamp

QTY

QTY

Cat. No. 43901



Fax (Free): 0800 012 1476Fax (Free): 1-800 535 538


Cat. No. E43007Z1 Punch Holder with Wedge, Dual Clamps


E437004370930160

E43519F24302E43505E437024348643499E43708



M10 x 35mm Lg S.H.C.S.14.3mmO/ x 22.2mm Lg SpringZ1 Wedge Punch Holder BodyM10 Locking Cap With Screw


PRICENo.

123456789

10

1112241221

Cat. No. E43007iZ1 Punch Holder with Interlocking Wedge, Dual Clamps


E437004370930160

E43519F24302E43505E437024348643499

E43708i



M10 x 35mm Lg S.H.C.S.14.3mmO/ x 22.2mm Lg SpringZ1 Wedge Punch Holder BodyM10 Locking Cap With Screw


PRICENo.

123456789

10

1112241221

QTY

QTY



Fax (Free): 0800 012 1476Fax (Free): 1-800 535 538


Cat. No. 43904Z2 Punch Holder with Wedge, Single Clamp


E437314370930160

E43519F43504E43505E43729E43730




Z2 Wedge

PRICENo.

12345678

11114211

Cat. No. 43904i Z2 Punch Holder with Interlocking Wedge, Single Clamp


E437314370930160

E43519F43504E43505E43729E43730i




Z2 Inter-Locking Wedge

PRICENo.

12345678

11114211

QTY

QTY



Fax (Free): 0800 012 1476Fax (Free): 1-800 535 538


Cat. No. E43008Z2 Punch Holder with Wedge, Dual Clamps


E437314370930160

E43519F24302E43505E437294348643504E43730



M10 x 70mm Lg14.3mmO/ x 22.2mm Lg SpringZ2 Wedge Punch Holder BodyM10 Locking Cap With Screw


PRICENo.

123456789

10

1112241221

Cat. No. E43008iZ2 Punch Holder with Interlocking Wedge, Dual Clamp


E437314370930160

E43519F24302E43505E437294348643504

E43730i



M10 x 70mm Lg 14.3mmO/ x 22.2mm Lg SpringZ2 Wedge Punch Holder BodyM10 Locking Cap With Screw


PRICENo.

123456789

10

1112241221

QTY

QTY

European Style Manual Clamps - Dual Clamp Kit


Fax (Free): 0800 012 1476Fax (Free): 1-800 535 538


Cat. No. 43906

Z1 & Z2 Punch Holder Dual Clamp Kit


43486E43505E43519F24302

M10 Locking Cap With Screw 5/16”14.3mmO/ x 22.2mm Lg Spring

Safety ClampM10 x 70mm Lg S.H.C.S

PRICENo.

1234

2212

QTY

European Die Holders


Fax (Free): 0800 012 1476Fax (Free): 1-800 535 538


39mm

60mm

*Note: Please verify press brake tongue slot widthwhen ordering.

CAT. NO.

43016

*Note: Please contact the sales desk for a list of information that will be required prior to ordering.Solid piece made to length for bed of press brake. Please contact the sales desk.

Call for pricing information

Cat. No. 43006 and 43016


50.8mm

60mm

Cat No. 43006

Cat No. 43016

CAT. NO. L835mm

S415mm

43006


Fax (Free): 0800 012 1476Fax (Free): 1-800 535 538


Features:• Solid steel construction

• Mobile base with heavy duty casters

with a rated capacity of 408

kilograms each

• Three 177mm drawers capable of

holding five punches each

• Two 50.8mm drawers capable of holding

five dies each

• Punches are held upright in custom steel

U-channels to prevent damage to tips

and mounting tongues

• Dies are separated by custom

U-channels to prevent damage to

V-openings

• Individual latches on all drawers

• Safety interlock to prevent the opening

of more than one drawer at a time

• Full width handles with end caps and

paper labelling strips with clear

protective label covers

• Retainer top with rubber mat

• Cabinet dimensions: 1067mm high,

1022.35mm wide, 571.5mm deep.

Cat. No. 90007

Wilson Press Brake Tooling Cabinet

PRICECAT. NO.

90007

Wilson Press Brake Tooling Cabinet

Index


Fax (Free): 0800 012 1476Fax (Free): 1-800 535 538


2V Dies

2V Die Holders

2V Die Rail And Clamp

2V Dies With Large Shoulder Radii

3V Hemming Die

30° Acute-Angle Punches

60° Acute-Angle Punches

75° Punches

85° Gooseneck Punches


88° & 90° Gooseneck Punches With Thin Tip

88° Narrow Punches

88° Sash Punches


90° Narrow Punches

90° Sash Punches

Acute-Angle Large 1V Dies



Air Bending Force Chart Metric

Bend Limit Graphs

Deep Punch Holder

Dual Clamping Kits


European Punch Holders

Express Clamping System

Flattening Die

Flattening Punches

Hemming Dies

Large 1V Dies

Large 1V Die Holder

46

50

50

49

66

14-15

16

17-18

11

8-9

10

12

13

11

12

14

62

58

44

85

23-40

74

77, 79

81

80

4-5

66

22

66

63-65

65


Low Profile Quick Change 1V Dies

Low Profile Sectionalised 2V Dies


Quick Change 1V Die Holder And

Wedge Block



Quick Change 2V Dies With Large

Shoulder Radii



Quick Change Back Gauge Stopper Pads

Quick Change Rail Style Flattening Die

Quick Reference Chart

Rail Style Offset Tools

Sectionalised 2V Dies

Sectionalised 2V Dies With Large

Shoulder Radii

Side Gauge

Squaring Arm

Stacking Rails



Standard 88˚ & 90˚ Punches With Thin Tip

Standard Die Lengths

Standard Punch Lengths

Tooling Cabinet

Urethane Holders

Urethane Pads

Urethane Rolls

20-21

57

49

73

60-61

51-56

41-46

44

59

45

72

66

2-3

71

47-48

49

73

73

50

6

6

7

1

1

82

69

70

73

Notes


Fax (Free): 0800 012 1476Fax (Free): 1-800 535 538


Notes


Fax (Free): 0800 012 1476Fax (Free): 1-800 535 538


TIR

V

MF

160

123.

226

.7

45.0

63.0

112.

015

2.0

125

96.3

20.8

28.0

40.5

52.5

84.0

144. 0

V (

mm

)M

FIR T O N S P E R M E T R E

74.

91.

2

3.3

7.2

10.0

14.0

85.

61.

3

3.2

5.6

9.0

13.2

15.4

10 7.0

1.7

4.4

7.0

10.8

14.0

17.6

12 8.6

2.0

5.5

8.4

12.6

16.0

22.0

1410

.1 2.3

7.5

9.8

14.4

20.0

25.3

1611

.5 2.7

6.6

8.8

11.2

18.0

23.0

28.6

200

154.

033

.3

54.0

84.0

118.

817

6.0

225.

0

250

192.

541

.7

72.0

99.8

137.

517

5.0

270.

0

100

75.0

16.7

24.0

31.5

56.3

70.0

108. 0

8060

.013

.3

22.5

31.5

43.8

72.0

90.0

6347

.310

.5

14.0

18.0

20.3

26.3

37.5

56.0

5037

.5 8.3

14.4

15.8

22.0

28.1

35.0

54.0

4030

.0 6.7

16.5

17.6

21.9

28.0

36.0

45.0

60.0

3224

.0 5.3

12.7

14.3

21.0

22.4

28.0

36.0

45.0

55.0

2518

.0 4.2

11.0

14.4

18.2

27.0

28.8

35.0

44.0

2014

.4 3.3

8.8

14.0

18.4

23.4

30.0

35.2

22*

15.8 3.7

12.5

16.1

20.8

28.5

331

.938

.5

1813

.0 3.0

7.7

10.0

16.0

20.7

26.0

33.0

THIC

KN

ESS

0.5m

m0.

6mm

0.8m

m1.

0mm

1.2m

m1.

4mm

1.6m

m2.

0mm

2.3m

m2.

6mm

3.0m

m3.

2mm

3.5m

m4.

0mm

4.5m

m5.

0mm

6.0m

m7.

0mm

9.0m

m10

.0m

m12

.0m

m16

.0m

m19

.0m

m22

.0m

m25

.0m

m30

.0m

m

42.

80.

7

4.5

6.0

64.

21.

0

2.8

4.2

8.0

11.0

AIR

BE

ND

IN

G F

OR

CE

CH

AR

T

ME

TR

IC

STA

ND

AR

D F

OR

MU

LAS

FOR

SEL

ECTI

NG

A V

-OP

ENIN

G

MA

TER

IAL

THIC

KN

ESS:

2.6m

m O

R LE

SS =

T x

63.

0mm

- 8

.0m

m =

T x

89.

00m

m -

12.

00m

m =

T x

10

14.0

0mm

& T

HIC

KER

= T

x 1

2

NO

TE

:Th

e ab

ove

form

ulas

are

for

ref

eren

ce o

nly.

For

mor

e sp

ecifi

c in

form

atio

n, p

leas

e re

fer

to t

he c

hart

bel

ow.

T =

MA

TE

RIA

L T

HIC

KN

ES

S

•

V =

V-O

PE

NIN

G

•

MF

= M

INIM

UM

FL

AN

GE

LE

NG

TH

•

IR

= I

NS

IDE

RA

DIU

STh

e b

end

ing

forc

e (to

nnag

e) f

igur

es li

sted

ab

ove

are

bas

ed o

n m

ild s

teel

with

a t

ensi

lest

reng

th o

f 45

-50

kilo

gram

s p

er s

qua

re m

illim

etre

. To

calc

ulat

e th

e ap

pro

xim

ate

ben

din

gfo

rce

(tonn

age)

req

uire

men

ts f

or o

ther

mat

eria

ls, p

leas

e us

e th

e m

ultip

liers

list

ed.

Soft

Bras

s....

......

......

......

......

......

...To

ns P

er M

etre

x 5

0%So

ft A

lum

iniu

m..

....

....

....

....

....

....

...

Tons

Per

Met

re x

50%

Hea

t Tre

ated

Alu

min

ium

Allo

ys...

..To

ns P

er M

etre

x 1

00%

Stai

nles

s St

eel..

......

......

......

......

....T

ons

Per

Met

re x

150

%

Not

e: *

Base

d on

ben

ding

to a

n in

clud

ed a

ngle

of

88 d

egre

es.

This

dim

ensi

on w

ill in

crea

se w

hen

bend

ing

to a

n in

clud

ed a

ngle

of

less

than

88

degr

ees.

PRECISION TOOLING.UNBEATABLE PERFORMANCE.

For more than 40 years, Wilson Tool International®

has provided industry-leading tooling solutions that

enhance the performance of sheet metal

fabricators.

The three divisions of Wilson Tool – Punch Press,

Press Brake and Xtra – represent the most

comprehensive line of tooling systems and

accessories available. Our ability to consistently

provide innovative, high quality products that

outlast and outperform the competition is why

the world’s most successful fabricators rely upon

Wilson Tool tooling systems.

A knowledgeable global sales force, multilingual

customer support staff, same-day shipping and

extensive distribution network are just a few of

the benefits that keep our customers coming

back time and again.

WILSON TOOL INTERNATIONAL

European HeadquartersUnited KingdomStirling Road, South Marston Industrial Estate, Swindon,Wiltshire, SN3 4TQ United KingdomPress Brake: 0800 012 1475Tel: +44 (0) 1793 831818Fax: +44 (0) 1793 831945Email: [email protected]

12912 Farnham AvenueWhite Bear Lake, MN 55110 USATel: (651) 286 6001Fax: (651) 286 5959Email: [email protected]

FranceBât B51 Rue D’Ourdy77550 Réau, FranceTel: +33 (0) 164 13 47 80Fax: +33 (0) 164 13 47 81Email: [email protected]

GermanyGottlieb Daimler Str 231552 Rodenberg, GermanyTel: +49 5723 747 0Fax: +49 5723 747 10Email: [email protected]

ScandinaviaIslevdalvej 100 DK-2610, Rodovre, DenmarkTel: +45 44 53 16 99 Fax: +45 44 53 06 07 Email: [email protected]

ChinaNo. 6 Building of 584018 Lane Huaning RoadXinzhuang Industry Park201108 Shanghai, ChinaTel: +86 21 51089638Fax: +86 21 64422195Email: [email protected]

email:[email protected] us online at:www.wilsontool.com

Worldwide HeadquartersUnited States

WILSON TOOL INTERNATIONAL - OCTOBER 2008

www.wilsontool.ro

Distribuitor:

S.C. SM TECH SRL

Tehnologii şi soluţii pentru industria prelucrării tablelor

Tel: 0040-331-401599 Tel/Fax: 0040-231-515702 Tel Mob: 0040-745-528494

E-mail: office (at) sm-tech.ro Web:

www.sm-tech.ro www.wilsontool.ro

Vă stăm la dispoziţie cu plăcere cu orice informaţie sau ofertă pentru scule

Wilson Tool destinate maşinii d-voastră de ştantat CNC sau presei d-voastră abkant

Documents

Wilson Tool - Press Brake Tooling Eurostyle - SM TECH - scule pentru abkanturi Amada Promecam style