YDRAFORCE Solenoid Valves - Altan · PDF fileManual Override “M” Option for Three-Position Push/Pull-Type Solenoid Valves Note: This option is not available along with the Waterproofing

• Poppet or spool types.

• Operating pressures to 345 bar (5000 psi).

• Hardened precision poppets, seats, spools and cagesfor long life and low leakage.

• Durable, unitized, molded coils.

• Water/Weather resistant coils are available with IP65and IP69 rated connectors for most valves.

• Manual override available on most models.

• Industry common cavities—compact sizes.

• Cartridges are voltage interchangeable.

• Wide variety of voltage and connector options.

• Low voltage pull-in characteristics.

• Coils are rated for continuous duty operation.

1.000.1

Solenoid Valves

Poppet type valves are two-way, normally open or normallyclosed, load holding or blocking valves for applicationsrequiring low internal leakage. Models are available for flowsup to 150 lpm (40 gpm).

Spool type valves are two-way, normally open or normallyclosed, three-way, four-way, four-way three-position, andsix-way. The four-way three-position valves are available intandem center, open center, closed center or “motor spool”configurations. Models are available for flows up to 75 lpm(20 gpm).

Blocking/low flow valves are two-way normally-closed, load-holding or venting valves, and two-position three-wayblocking valves.

HYDRAFORCE®

SOLENOID VALVES

Manual Override Options

1.001.1

Manual Override “M” Option for Two-Position Pull-Type Solenoid Valves

Manual Override “M” Option for Three-Position Push/Pull-Type Solenoid Valves

Note: This option is not available along with the Waterproofing option.

Note: This option is provided with the Waterproofing option.

Exaggerated illustration of operation of Manual Override “M” option

Note: The manual override feature is intended for emergency use, not for continuous-duty operation.

Note: The manual override feature is intended for emergency use, not for continuous-duty operation.

UPPERSPRINGS

NORMALPOSITION

SHIFTEDPOSITION

To Override:1) Push Down

To Returnto NormalOperation:1) PushButtonDown

2) Twist Button Counterclockwise 180°

2) Twist Button Clockwise 180°

3) ReleaseButton

3) ReleaseButton

8 SIZE 10 SIZE

Manual Override Options

1.001.2

Manual Override “P” and “K” Options for Two-Position Push-Type Solenoid Valves

Note: This option is not available along with the Waterproofing option.Note: The manual override feature is intended for emergency use, not for continuous-duty operation.

Manual Override “J” and “Y” Options for Pull-Type Solenoid ValvesSizes: -38 (for -08 cavities), -10, -12, -16Note: The manual override feature is intended for emergency use, not for continuous-duty operation.

MANUALOVERRIDEOPTION “P”MANUAL

OVERRIDEOPTION “P”

MANUALOVERRIDEOPTION “K”

MANUAL OVERRIDE OPTION “J”WITH RED KNOB (#6113032)

ORDERED SEPARATELY

MANUAL OVERRIDE OPTION “Y”

MANUAL OVERRIDE OPTION “J”

MANUALOVERRIDEOPTION “K”

HYDRAFORCE®

SOLENOID VALVES

SV08-20 Poppet, 2-Way, Normally Closed

DESCRIPTIONA solenoid-operated, 2-way, normally closed, piloted poppet-type, screw-in hydrauliccartridge valve, intended to act as a blocking or load-holding device for low flowcircuits.

OPERATIONWhen de-energized, the SV08-20 acts as a check valve, allowing flow from ➀ to ➁,while blocking flow from ➁ to ➀.When energized, the cartridge's poppet lifts to open the ➁ to ➀ flow path. In thismode, flow from ➀ to ➁ is severely restricted. If this path is required, see modelSV08-22, page 1.041.1.Operation of Manual Override Option: To override, push button in, twist counter-clockwise 180°, and release. In this position, the valve will remain open.

To return to normal operation, push button in, twist clockwise 180°, and release.Override will be detented in this position.

FEATURES• Continuous-duty rated coil.• Hardened seat for long life and low leakage.• Optional coil voltages and terminations.• Cartridges are voltage interchangeable.• Unitized, molded coil design.• Manual override option.• Optional waterproof E-Coils rated up to IP69K.• Industry common cavity.• Compact size.

RATINGSOperating Pressure: 207 bar (3000 psi)Proof Pressure: 255 bar (3700 psi)

Flow: See Performance Chart

Internal Leakage: 0.15 cc/minute (3 drops/minute) max. at 207 bar (3000 psi)Temperature: -40 to 120°C with standard Buna seals

Coil Duty Rating: Continuous from 85% to 115% of nominal voltage

Response Time: First indication of change of state with 100% voltage supplied at80% of nominal flow rating:Energized: 40 msec.; De-energized: 46 msec.

Initial Coil Current Draw at 20°C: Standard Coil: 1.2 amps at 12 VDC; 0.13 amps at115 VAC (full wave rectified); E-Coil: 1.4 amps at 12 VDC; 0.7 amps at 24 VDC

Minimum Pull-in Voltage: 85% of nominal at 207 bar (3000 psi)

Filtration: See page 9.010.1Fluids: Mineral-based or synthetics with lubricating properties at viscosities of

7.4 to 420 cSt (50 to 2000 ssu)

Installation: No restrictions; See page 9.020.1Cavity: VC08-2; See page 9.108.1

Cavity Tool: CT08-2XX; See page 8.600.1

Seal Kit: SK08-2X-T; See page 8.650.1Coil Nut: Part No. 7004400;

For E-coils manufactured prior to 1-1-04, see page 3.400.1 for coil nut info.

SYMBOLS

USASI: ISO:

PERFORMANCE (Cartridge Only)

1.010.1

8.6/125

6.9/100

5.2/75

3.4/50

1.7/25

7.52

15.14

22.76

FLOW lpm/gpm

PR

ES

SU

RE

DR

OP

bar

/psi

to — (e); to - - - (d)32 cSt/150 ssu oil at 40°C

30.28

10.3/150

➁ ➁➀ ➀

SV08-20

DIMENSIONS

MATERIALS

Cartridge: Weight: 0.09 kg.(0.20 lbs.); Steel with hardenedwork surfaces. Zinc-platedexposed surfaces; Buna NO-rings and back-ups standard.

Standard Ported Body: Weight:0.16 kg. (0.35 lbs.); Anodizedhigh-strength 6061 T6 aluminumalloy, rated to 240 bar (3500 psi);See page 8.008.1. Ductile ironand steel bodies available;dimensions may differ; consultfactory.

Standard Coil: Weight: 0.11 kg.(0.25 lbs.); Unitized thermoplas-tic encapsulated, Class H hightemperature magnetwire; Seepage 3.200.1.

E-Coil: Weight: 0.14 kg. (0.3 lbs.);Perfect wound, fully encapsu-lated with rugged external metalshell; Rated up to IP69K withintegral connectors; Note: Seepage 3.400.1 for all E-Coilretrofit applications.

OptionNone (Blank)

150µ Screen SManual Override M

SV08-20__ - __ __ __ - __ - __ __ __ __ __

TO ORDER

1.010.2

PortingCartridge Only 0

SAE 4 4TSAE 6 6TSAE 8 8T

1/4 in. BSP* 2B3/8 in. BSP* 3B

*BSP Body; U.K. Mfr. Only

1.4035.6

1.8847.7

1.41 DIA.35.8

0.4310.9

StandardCoil View

E-CoilView

HYDRAFORCE®

SealsBuna N (Std.) NFluorocarbon V

Termination (VDC) Std. CoilDS Dual SpadesDG DIN 43650DL Leadwires (2)

DL/W Leads w/Weatherpak®

ConnectorsDR Deutsch DT04-2P

Termination (VAC) Std. CoilAG DIN 43650AP 1/2 in. Conduit

Termination (VDC) E-CoilER Deutsch DT04-2P

(IP69K Rated)EY Metri-Pack® 150

(IP69K Rated)

Coils with internal diode areavailable. Consult factory.

VoltageStd. Coil

0 Less Coil** 10 10 VDC†

12 12 VDC 24 24 VDC 36 36 VDC 48 48 VDC 24 24 VAC115 115 VAC230 230 VAC**Includes Std. Coil Nut† DS, DW or DL

terminations only

E-Coil10 10 VDC12 12 VDC20 20 VDC24 24 VDC

SOLENOID VALVES

SV08-20J Poppet, 2-Way, Normally Closed,

DESCRIPTIONA solenoid-operated, 2-way, normally closed, poppet-type, screw-in hydrauliccartridge valve, with either “J” or “Y” type manual override standard. This valve isintended as a blocking or load holding device for low flow circuits having pull-onlymanual override requirements for handles or cable linkage.

OPERATIONWhen de-energized, the SV08-20J/Y acts as a check valve, allowing flow from ➀ to➁, while blocking flow from ➁ to ➀.

When energized, the valve’s poppet lifts to open the ➁ to ➀ flow path, while flow from➀ to ➁ is severely restricted.

Operation of Manual Override Option: To manually override, pull and hold theknurled knob. This override is not detented. The pull force required is approximately24 lbs. The “J” option includes a male 10-32 thread for a cable attachment. If a cableis used, the internal valve spring may not provide enough force to overcome internalcable friction. An external means of returning the cable must be provided by the user.

FEATURES• Continuous-duty rated coil.• Hardened parts for long life.• Optional coil voltages and terminations.• Optional waterproof E-Coils rated up to IP69K.• Manual override standard.• Industry common cavity.• Compact size.

RATINGSMaximum Operating Pressure: 207 bar (3000 psi)Proof Pressure: 255 bar (3700 psi)

Flow: See Performance ChartTemperature: -40 to 120°C with standard Buna seals

Coil Duty Rating: Continuous from 85% to 115% of nominal voltage


Minimum Pull-in Voltage: 85% of nominal at 40°C; Drop Out 5%

Filtration: See page 9.010.1Fluids: Mineral-based or synthetics with lubricating properties at viscosities of

7.4 to 420 cSt (50 to 2000 ssu)

Installation: No restrictions; See page 9.020.1Cavity: VC08-2; See page 9.108.1

Cavity Tool: CT08-2XX; See page 8.600.1

Seal Kit: SK08-2X-T; See page 8.650.1Coil Nut: Part No. 7004400;


SYMBOLS

USASI: ISO:


1.011.1

12.4/180

11.0/160

5.5/80

2.8/40

8.3/120

7.52

11.43

3.81

15.14

18.95

26.67

22.76

FLOW lpm/gpm

PR

ES

SU

RE

DR

OP

bar

/psi

➁ to ➀ Energized ——➀ to ➁ De-energized - - - -32 cSt/150 ssu oil at 40°C

2

1

DIMENSIONS

MATERIALS

Cartridge: Weight: 0.15 kg. (0.33 lbs.);Steel with hardened work surfaces.Zinc-plated exposed surfaces; BunaN O-rings and back-ups standard.

Standard Ported Body: Weight:0.16 kg. (0.35 lbs.); Anodized high-strength 6061 T6 aluminum alloy,rated to 240 bar (3500 psi); See page8.008.1. Ductile iron and steel bodiesavailable; dimensions may differ;consult factory.

Standard Coil: Weight: 0.11 kg.(0.25 lbs.); Unitized thermoplasticencapsulated, Class H high tempera-ture magnetwire; See page 3.200.1.

E-Coil: Weight: 0.14 kg. (0.3 lbs.); Fullyencapsulated with rugged externalmetal shell; Rated up to IP69K withintegral connectors; Note: See page3.400.1 for all E-Coil retrofitapplications.

TO ORDER

1.011.2

OptionCable Adapter JKnurled Knob Y





SV08-20J

SV08-20 J - __ __ __ - __ - __ __ __ __ ____

1.2331.4

INCHMILLIMETRE

0.6015.2

0.287.11.62

41.10.133.3

2.0050.8*

1.0927.7

1.5038.1

*BSP BODY55.9 mm

TORQUE20 ft-lbs.(27.1 Nm)max.

TORQUE5 ft-lbs.(6.8 Nm)max.

0.7519.1 2.00

50.8

1.4035.6

0.7117.9

2

1

2

1

1.1328.7

COIL MUST BEINSTALLED WITHLETTERING UP

3.1279.3

0.389.5

0.092.26

10–32UNF–2A

'Y' OPTION

MANUAL OVERRIDE STROKE

'J' OPTION WITHRED KNOB ORDERED

SEPARATELY#6113032

'J' CAP ACROSS FLATS

.87522.2

ACROSS

FLATS

1.1328.7

1.7745.0

1.8847.7

StandardCoil View

E-CoilView

with Pull Only Manual Override

HYDRAFORCE®


Termination (VDC)Std. Coil

DS Dual SpadesDG DIN 43650DL Leadwires (2)



Termination (VAC)Std. Coil

AG DIN 43650AP 1/2 in. Conduit

Termination (VDC)E-Coil

ER Deutsch DT04-2P(IP69K Rated)

EY Metri-Pack® 150(IP69K Rated)


VoltageStd. Coil



terminations only


SOLENOID VALVES

SF08-20 Poppet, 2-Way, N.C., High Pressure


OPERATIONWhen de-energized, the SF08-20 acts as a check valve, allowing flow from ➀ to ➁,while blocking flow from ➁ to ➀.When energized, the cartridge's poppet lifts to open the ➁ to ➀ flow path. In thismode, flow from ➀ to ➁ is severely restricted. If this path is required, see modelSF08-22, page 1.042.1.

FEATURES• Continuous-duty rated coil.• Hardened seat for long life and low leakage.• Optional coil voltages and terminations.• Cartridges are voltage interchangeable.• Unitized, molded coil design.• Optional waterproof E-Coils rated up to IP69K.• Industry common cavity.• Compact size.

RATINGSOperating Pressure: 345 bar (5000 psi)Flow: See Performance ChartInternal Leakage: 0.15 cc/minute (3 drops/minute) max. at 345 bar (5000 psi)Temperature: -40 to 120°C with standard polyurethane sealsCoil Duty Rating: Continuous from 85% to 115% of nominal voltageInitial Coil Current Draw at 20°C: Standard Coil: 1.2 amps at 12 VDC; 0.13 amps at

115 VAC (full wave rectified); E-Coil: 1.4 amps at 12 VDC; 0.7 amps at 24 VDCMinimum Pull-in Voltage: 85% of nominal at 345 bar (5000 psi)Filtration: See page 9.010.1Fluids: Mineral-based or synthetics with lubricating properties at viscosities of

7.4 to 420 cSt (50 to 2000 ssu)Installation: No restrictions; See page 9.020.1Cavity: VC08-2; See page 9.108.1Cavity Tool: CT08-2XX; See page 8.600.1Seal Kit: SK08-2P-T; See page 8.650.1Coil Nut: Part No. 7004400;


SYMBOLS

USASI: ISO:


1.012.1

11.0/160

8.3/120

5.5/80

2.8/40

3.81

7.52

18.95

FLOW lpm/gpm

PR

ES

SU

RE

DR

OP

bar

/psi

➁ to ➀ — (e); ➀ to ➁ - - - (d)32 cSt/150 ssu oil at 40°C

22.76

12.4/180

11.43

15.14

26.57

SF08-20

DIMENSIONS

1.012.2


SAE 6 6TDSAE 6 6TSSAE 8 8TDSAE 8 8TS

1/4 in. BSP* 2BD1/4 in. BSP* 2BS3/8 in. BSP* 3BD3/8 in. BSP* 3BS


1.4035.6

1.8847.7

1.41 DIA.35.8

0.4310.9

StandardCoil View

E-CoilView

HYDRAFORCE®

MATERIALS

Cartridge: Weight: 0.15 kg.(0.33 lbs.); Steel with hardenedwork surfaces. Zinc-platedexposed surfaces; Polyurethanecast O-rings and Fluorocarbonback-up standard.

Ported Body: Weight: 0.54 kg.(1.2 lbs.), Steel, zinc-plated(code "S"); or Ductile Iron(code "D") standard, consultfactory for weight, dimensionsmay differ; rated to 345 bar(5000 psi); See page 8.008.1.


E-Coil: Weight: 0.14 kg. (0.3 lbs.);Fully encapsulated with ruggedexternal metal shell; Rated up toIP69K with integral connectors;Note: See page 3.400.1 for allE-Coil retrofit applications.

OptionNone (Blank)

ManualOverride M

SF08-20__ - __ __ __ - __ - __ __ __ __ __

TO ORDER

SealsPolyurethane P

(Std.)











VoltageStd. Coil



terminations only


SOLENOID VALVES

SV38-20J Poppet, 2-Way, Normally Closed

DESCRIPTIONA solenoid-operated, 2-way, normally closed, piloted poppet-type, screw-in hydrauliccartridge valve, intended to act as a blocking or load-holding device for low flowcircuits having manual override requirements.

OPERATIONWhen de-energized, the SV38-20J acts as a check valve, allowing flow from ➀ to ➁,while blocking flow from ➁ to ➀.When energized, the cartridge's poppet lifts to open the ➁ to ➀ flow path. In thismode, flow from ➀ to ➁ is severely restricted.

Operation of Manual Override Option: To manually override, pull and hold theknurled knob. This override is not detented. The pull force required is approximately20 lbs. The “J” option includes a male 10-32 thread for a cable attachment. If a cableis used, the internal valve spring may not provide enough force to overcome internalcable friction. An external means of returning the cable must be provided by the user.

FEATURES• Continuous-duty rated coil.• Hardened seat for long life and low leakage.• Optional coil voltages and terminations.• Cartridges are voltage interchangeable.• Unitized, molded coil design.• Manual override option.• Optional waterproof E-Coils rated up to IP69K.• Industry common cavity.• Compact size.

RATINGSOperating Pressure: 207 bar (3000 psi)Flow: See Performance Chart

Internal Leakage: 0.15 cc/minute (3 drops/minute) max. at 207 bar (3000 psi)

Temperature: -40 to 120°C with standard Buna sealsCoil Duty Rating: Continuous from 85% to 115% of nominal voltage

Initial Coil Current Draw at 20°C: Standard Coil: 1.67 amps at 12 VDC; 0.18 ampsat 115 VAC (full wave rectified); E-Coil: 2.0 amps at 12 VDC; 1.0 amps at 24 VDC


Filtration: See page 9.010.1

Fluids: Mineral-based or synthetics with lubricating properties at viscosities of7.4 to 420 cSt (50 to 2000 ssu)

Installation: No restrictions; See page 9.020.1

Cavity: VC08-2; See page 9.108.1Cavity Tool: CT08-2XX; See page 8.600.1

Seal Kit: SK08-2X-T; See page 8.650.1

Coil Nut: Part No. 7004380;For E-coils manufactured prior to 1-1-04, see page 3.400.1 for coil nut info.

SYMBOLS

USASI: ISO:


1.013.1

3.4/50

4.1/60

2.8/40

1.4/20

0.7/10

2.1/30

7.52

11.43

3.81

15.14

18.95

22.76

FLOW lpm/gpm

PR

ES

SU

RE

DR

OP

bar

/psi

to — (e)32 cSt/150 ssu oil at 40°C

➁ ➀

DIMENSIONS

MATERIALS

Cartridge: Weight: 0.09 kg. (0.20 lbs.);Steel with hardened work surfaces.Zinc-plated exposed surfaces; BunaN O-rings and back-ups standard.

Standard Ported Body: Weight:0.16 kg. (0.35 lbs.); Anodized high-strength 6061 T6 aluminum alloy,rated to 240 bar (3500 psi); Seepage 8.008.1. Ductile iron and steelbodies available; dimensions maydiffer; consult factory.


E-Coil: Weight: 0.41 kg. (0.9 lbs.); Fullyencapsulated with rugged externalmetal shell; Rated up to IP69K withintegral connectors; Note: See page3.400.1 for all E-Coil retrofitapplications.

TO ORDER

1.013.2

Option*Standard J

150µ Screen S*Cable Release Y*See Page 1.001.1





SV38-20J

SV38-20 J - __ __ __ - __ - __ __ __ __ ____

1.62

COIL MUST BE INSTALLEDWITH LETTERING UP

41.11.84

DIA.46.7

StandardCoil View

E-CoilView

HYDRAFORCE®












VoltageStd. Coil



terminations only



DESCRIPTIONA solenoid-operated, 2-way, normally closed, poppet-type, screw-in hydraulic cartridge valve, designed to function as a load holding or blocking valve in applications requiring low internal leakage.

OPERATIONWhen de-energized, the SV10-20 acts as a check valve, allowing flow to pass from 1 to 2, while blocking flow in the reverse direction. With the sensor option, the neutral sensor will signal ON or HIGH.When energized, the poppet lifts to open the 2 to 1 flow path. In this mode, flow from 1 to 2 is severely restricted. (If this path is required, see model SV10-22, page 1.044.1.) With the sensor option, the neutral sensor will signal LOW or OFF.Operation of Manual Override Option: To override, push button in, twist counter-clockwise 180° and release. In this position, the valve will remain open.To return to normal operation, push button in, twist clockwise 180° and release. Override will be detented in this position.

FEATURES• Continuous-duty rated solenoid. • Manual override option.• Hardened seat for long life and low leakage. • Unitized, molded coil design.• Optional coil voltages and terminations. • Industry common cavity.• Efficient wet-armature construction.• Cartridges are voltage interchangeable.• Optional waterproof E-Coils rated up to IP69K.

RATINGSOperating Pressure: 241 bar (3500 psi)Proof Pressure: 345 bar (5000 psi)Flow: Up to 56.8 lpm (15 gpm); see performance chartInternal Leakage: 0.15 cc/minute (3 drops/minute) max. at 207 bar (3000 psi)Temperature: -40 to 100°C (-40° to 212°F) with standard Buna N seals

-26 to 204°C (-15°F to 400°F) with Fluorocarbon sealsSensor Option: -40°C to 110°C (-40°F to 230°F)

Coil Duty Rating: Continuous from 85% to 115% of nominal voltageResponse Time: First indication of change of state with 100% voltage supplied at

80% of nominal flow rating: Energized: 40 msec.; De-energized: 32 msec.Response Time with Sensor: 53 ms pull-in, 110 ms drop-out

Initial Coil Current Draw at 20°C: Standard Coil: 1.67 amps at 12 VDC; 0.18 amps at 115 VAC (full wave rectified). E-Coil: 1.7 amps at 12 VDC; 0.85 amps at 24 VDC

Minimum Pull-in Voltage: 85% of nominal at 207 bar (3000 psi)Filtration: See page 9.010.1 Fluids: Mineral-based or synthetics with lubricating properties at viscosities of

7.4 to 420 cSt (50 to 2000 sus); See Temperature and Oil Viscosity, page 9.060.1Installation: No restrictions; See page 9.020.1Cavity: VC10-2; See page 9.110.1; Cavity Tool: CT10-2XX; See page 8.600.1Seal Kit: SK10-2X-T; See page 8.650.1Coil Nut: Part No. 7004400

ISO: with Sensor:

1.016.1

SYMBOLS


SOLENOID VALVES

HYDRAFORCE.com®

8.6/125

6.9/100

5.2/75

3.4/50

1.7/25

11.43

22.76

34.19

45.412

FLOW lpm/gpm

PR

ES

SU

RE

DR

OP

bar

/psi

SV10-20 without Sensor2 to 1 energized ——

1 to 2 de-energized - - - -32 cSt/150 sus oil at 40°C

56.815

13.8/200

16.5/240

19.3/280

11.0/160

8.3/120

5.5/80

2.8/40

11.33

22.76

34.19

45.412

FLOW lpm/gpm

PR

ES

SU

RE

DR

OP

bar

/psi

SV10-20 with SensorPort 2 to 1 Energized ——

Port 1 to 2 De-energized - - - -32 cSt/150 sus oil at 40°C

56.815 VALVE SHIFT %

FLO

W

Vcc

SE

NS

OR

OU

TP

UT

Typical Sensor Output vs. Valve Shift

0

0.3 lpm0.08 gpm

56.8 lpm15 gpm

15 20 50 100

VOUT

Hatched Area: Overlapping Stroke, Leakage Flow

RP

Blue rectangles are links to other catalog pages.

http://www.hydraforce.com

SV10-20

DIMENSIONS

1.016.2

TO ORDER

SV10-(P)20(A)__ - __ __ __ - __ - __ __ __ __ __ - __ __

Option None (Blank)

Screen S Manual Override M Manual Override Y Manual Override J

For Manual Override optionssee page 1.001.1

1.6241.1

1.84DIA.

46.7

0.4511.4

E-CoilView

StandardCoil View

2.3860.3

Cartridge: Weight: 0.16 kg. (0.35 lbs.); Weight with Sen-sor option: 0.45 kg. (1.0 lbs.); Steel with hardened work surfaces. Zinc-plated exposed surfaces. Buna N O-rings and polyester elastomer back-up standard.

Standard Ported Body: Weight: 0.16 kg. (0.35 lbs.); Anodized high-strength 6061 T6 aluminum alloy, rated to 207 bar (3000 psi). Ductile iron bodies available; dimensions may differ. See page 8.010.1.

D-Coil: Weight: 0.27 kg. (0.60 lbs.); Unitized thermo-plastic encapsulated, Class H high temperature magnetwire. See page 3.200.1.

E-Coil: Weight: 0.41 kg. (0.9 lbs.); Fully encapsulated with rugged external metal shell. Rated up to IP69K with integral connectors. See page 3.400.1.

Porting Cartridge Only 0 SAE 6 6T SAE 8 8T 1/4 in. BSP* 2B 3/8 in. BSP* 3B 1/2 in. BSP* 4B*BSP Body; U.K. Mfr. Only

With sensor option, use model code SV10-P20A . . .See page 3.010.1

Without sensor option, use model code SV10-20 . . .

Voltage Std. Coil 0 Less Coil** 10 10 VDC†

12 12 VDC 24 24 VDC 36 36 VDC 48 48 VDC 24 24 VAC 115 115 VAC 230 230 VAC

**Includes D-Coil Nut† DS, DW or DL

terminations only

E-Coils: 10,12,20 or 24 VDC only.

MATERIALS

®HYDRAFORCE

HYDRAFORCE.com®

For Coils with Zener Diode, add “/Z” to option code. For example: “ER/Z”. Not available on all models. See coil option info. on pages 3.200.1 & 3.400.1

Coil Termination E-Coil D-CoilDeutsch DT04-2P ER (IP69K) DR (IP65)Metri-Pack® 150 EY (IP69K) DY (IP65)Dual Lead Wires EL (IP69K) DL (IP65)Amp Jr. Timer EJ (IP67) —DIN 43650 EG (IP65) DG (IP65)Dual Spades — DS (IP65)

Sensor/Connector N Neutral Sense/DT04-4P M Neutral Sense/M12-4P Mating Connectors: DT06-4S: Part No. 4001953 M12-4S: available at www.turck.com or www.binder-usa.com

Sensor Type 1 High to Low

Seals N Buna N (Std.) V Fluorocarbon

Sensor Option: See page 3.010.1

Dimensions will differ significantly with Sensor Option; see page 3.010.1.

RP



HSV10-20 HyPerformanceTM Poppet, 2-Way, N.C.

DESCRIPTIONA solenoid-operated, 2-way, normally closed, poppet-type, screw-in hydraulic cartridge valve, designed to function as a load holding or blocking valve in high pressure applications requiring low internal leakage.

OPERATIONWhen de-energized, the HSV10-20 acts as a check valve, allowing flow to pass from 1 to 2, while blocking flow in the reverse direction.When energized, the poppet lifts to open the 2 to 1 flow path. In this mode, flow from 1 to 2 is severely restricted.Operation of Manual Override Option: For normal operation (de-energized) the manual override pin must be seated in the lower detent groove. To shift the valve manually, the operator pushes down on the knob and rotates 180° in either direction. When the manual override is actuated, increased flow can be achieved by pulling on the knob.

FEATURES• Continuous-duty rated solenoid.• Hardened seat for long life and low leakage.• Optional coil voltages and terminations.• Efficient wet-armature construction.• Cartridges are voltage interchangeable.• Waterproof E-Coils rated up to IP69K.• 1000-hour salt-spray rated solenoid tubes and coils.• Unitized, molded coil design.• All HyPerformance products are tested to the rigorous standards

of the NFPA specification T2.6.1.• All HyPerformance valves are tested at a verification level of 90%

and an assurance of 99%.

RATINGSOperating Pressure: 350 bar (5075 psi); 10% Cycle Life: 420 bar (6090 psi)

Note: All HyPerformance products are tested for 900K cycles at 350 bar and 100K cycles at 420 bar.

Burst Pressure: 1380 bar (20,000 psi)Flow: Up to 75.7 lpm (20 gpm)Internal Leakage: 0.25 cc/minute (5 drops/minute) max. with 350 bar (5075 psi)

at port 2.Temperature: -54° to 107°C (-65° to 225°F) with Urethane sealsCoil Duty Rating: Continuous from 85% to 115% of nominal voltageResponse Time: First indication of change of state with 100% voltage supplied at

80% of nominal flow rating: Energized: 40 msec.; De-energized: 32 msec.Initial Coil Current Draw at 20°C: 1.7 amps at 12 VDC; 0.85 amps at 24 VDCMinimum Pull-in Voltage: 85% of nominal at 207 bar (3000 psi)Filtration: See page 9.010.1 Fluids: Mineral-based or synthetics with lubricating properties at viscosities of

7.4 to 420 cSt (50 to 2000 sus); See Temperature and Oil Viscosity, page 9.060.1Installation: No restrictions; See page 9.020.1Cavity: HVC10-2; See page 9.110.1Cavity Tool: HCT10-2xx; See page 8.600.1Seal Kit: SK10-2U-O; See page 8.650.1Coil Nut: Part No. 4553800

1.017.1

SYMBOL

PERFORMANCE (C artridge Only)

SOLENOID VALVES

HYDRAFORCE.com®

10.3/150

12.4/180

14.5/210

16.6/240

8.3/120

6.2/90

4.1/60

2.1/30

18.95

37.910

56.815

FLOW lpm/gpm

PR

ES

SU

RE

DR

OP

bar

/psi

Port 2 to 1, energized ——Port 1 to 2, de-energized - - - -

32 cSt/150 sus oil at 40°C

75.720

RP



HSV10-20

DIMENSIONS

1.017.2

TO ORDER

HSV10-20__ - __ __ __ - __ - __ __ __ __ __

Option None (Blank) Manual Override M

Cartridge: Weight: 0.19 kg. (0.41 lbs.); Steel with hardened work surfaces. Zinc-plated exposed surfaces. Urethane O-ring without back-up standard.

Ported Body: Weight: 1.19 kg. (2.62 lbs.); HyPerformance™Ductile iron (code ‘D’) standard. Rated to 345 bar (5000 psi).


Seals PPDI Urethane U

MATERIALS

®HYDRAFORCE

HYDRAFORCE.com®

Voltage 0 Less Coil** 10 10 VDC 12 12 VDC 20 20 VDC 24 24 VDC

For Coils with Zener Diode, add “/Z” to option code. For example: “ER/Z”. Not available on all models. See coil option info. on page 3.400.1

Coil TerminationDeutsch DT04-2P ER (IP69K)Metri-Pak 150 EY (IP69K)Dual Lead Wires EL (IP69K)Amp Jr. Timer EJ (IP67)DIN 43650 EG (IP65)

**Includes E-Coil Nut.

Recommended for pressures above 241 bar (3500 psi).

TORQUE:75 – 85 ft-lb.102 – 115 Nm

TORQUE: 5 – 7 ft-lb.6.8 – 9.5 Nm


2.54

ORIFICE DISC CANNOTBE USED WITH THIS PRODUCTdue to HyPerformanceTM Cavity.

64.5

18.3

1.00ACROSS FLATS

25.41.3133.3

0.7519.11.50

38.1

1.6241.1

1.0025.4 2.43

61.7

0.9223.4

2.0050.8

0.20

0.281 (7.1 mm)Dia. Mounting

Holes (2)

5.11.6341.3

2.4361.7

0.72

Porting Cartridge Only 0 SAE 8 8TD 1/2 in. BSP* 4BD*BSP Body; U.K. Mfr. Only

RP



SOLENOID VALVES


DESCRIPTIONA solenoid-operated, 2-way, normally closed, poppet-type, screw-in hydrauliccartridge valve, designed to function as a load holding or blocking valve inapplications requiring low internal leakage.

OPERATIONWhen de-energized, the SV12-20 acts as a check valve, allowing flow to pass from➀ to ➁, while blocking flow in the reverse direction.

When energized, the poppet lifts to open the ➁ to ➀ flow path. In this mode, flow from➀ to ➁ is severely restricted. If this path is required, see model SV12-22, page1.045.1.

Operation of Manual Override Option: To override, push button in, twist counter-clockwise 180° and release. In this position, the valve will remain open.

To return to normal operation, push button in, twist clockwise 180° and release.Override will be detented in this position.

FEATURES• Continuous-duty rated solenoid.• Hardened seat for long life and low leakage.• Optional coil voltages and terminations.• Efficient wet-armature construction.• Cartridges are voltage interchangeable.• Manual override option.• Optional waterproof E-Coils rated up to IP69K.• Unitized, molded coil design.• Cost effective cavity.

RATINGSOperating Pressure: 240 bar (3500 psi)Proof Pressure: 390 bar (5700 psi)Flow: See Performance ChartInternal Leakage: 0.15 cc/minute (3 drops/minute) max. at 240 bar (3500 psi)Temperature: -40 to 120°C with standard Buna sealsCoil Duty Rating: Continuous from 85% to 115% of nominal voltageResponse Time: First indication of change of state with 100% voltage supplied at

80% of nominal flow rating: Energized: 40 msec.; De-energized: 80 msec.Initial Coil Current Draw at 20°C: Standard Coil: 1.67 amps at 12 VDC; 0.18 amps

at 115 VAC (full wave rectified); E-Coil: 2.0 amps at 12 VDC; 1.0 amps at 24 VDCMinimum Pull-in Voltage: 85% of nominal at 207 bar (3000 psi)Filtration: See page 9.010.1Fluids: Mineral-based or synthetics with lubricating properties at viscosities of

7.4 to 420 cSt (50 to 2000 ssu)Installation: No restrictions; See page 9.020.1Cavity: VC12-2; See page 9.112.1Cavity Tool: CT12-2XX; See page 8.600.1Seal Kit: SK12-2X-T; See page 8.650.1Coil Nut: Part No: 7004400;


SYMBOLS

USASI: ISO:


1.018.1

10.3/150

8.3/120

6.2/90

4.1/60

2.1/30

37.910

75.820

113.630

FLOW lpm/gpm

PR

ES

SU

RE

DR

OP

bar

/psi


➁ ➀ ➁➀

SV12-20

DIMENSIONS

MATERIALS

Cartridge: Weight: 0.25 kg.(0.55 lbs.); Steel with hardenedwork surfaces. Zinc-platedexposed surfaces. Buna NO-rings and polyester elastomerback-up standard.

Standard Ported Body: Weight:0.57 kg. (1.25 lbs.); Anodizedhigh-strength 6061 T6 aluminumalloy, rated to 240 bar (3500psi); See page 8.012.1. Ductileiron and steel bodies available;dimensions may differ; consultfactory.

Standard Coil: Weight: 0.27 kg.(0.60 lbs.); Unitized thermoplas-tic encapsulated, Class H hightemperature magnetwire;See page 3.200.1.


TO ORDER

SV12-20 __ - __ __ __ - __ - __ __ __ __ __

OptionsNone (Blank)

Manual Override MManual Override YManual Override J

1.018.2



3/4 in. BSP* 6B1 in. BSP* 8B

*BSP Body;U.K. Mfrs. Only


TORQUE -35 ft-lbs(26.2 Nm)max.

1.6241.1

1.84DIA.

46.7

0.4511.4

E-CoilView

StandardCoil View

2.3860.5

HYDRAFORCE®












VoltageStd. Coil



terminations only


SOLENOID VALVES


DESCRIPTIONA solenoid-operated, 2-way, normally closed, poppet-type, screw-in hydrauliccartridge valve, designed to function as a load holding or blocking valve in applica-tions requiring low internal leakage.

OPERATIONWhen de-energized, the SV16-20 acts as a check valve, allowing flow to pass from ➀to ➁, while blocking flow in the reverse direction.

When energized, the poppet lifts to open the ➁ to ➀ flow path. In this mode, flow from➀ to ➁ is severely restricted. If this path is required, see model SV16-22, page1.046.1.



FEATURES• Continuous-duty rated solenoid.• Hardened seat for long life and low leakage.• Optional coil voltages and terminations.• Efficient wet-armature construction.• Cartridges are voltage interchangeable.• Manual override option.• Optional waterproof E-Coils rated up to IP69K.• Unitized, molded coil design.• Industry common cavity.

RATINGSOperating Pressure: 207 bar (3000 psi); Under certain operating conditions, this

valve may be used at higher pressures; consult facory.Proof Pressure: 390 bar (5700 psi)Flow: See Performance ChartInternal Leakage: 0.15 cc/minute (3 drops/minute) max. at 207 bar (3000 psi)Temperature: -40 to 120°C with standard Buna sealsCoil Duty Rating: Continuous from 85% to 115% of nominal voltageInitial Coil Current Draw at 20°C: Standard Coil: 1.67 amps at 12 VDC; 0.18 amps

at 115 VAC (full wave rectified). E-Coil: 2.0 amps at 12 VDC; 1.0 amps at 24 VDCMinimum Pull-in Voltage: 85% of nominal at 207 bar (3000 psi)Filtration: See page 9.010.1Fluids: Mineral-based or synthetics with lubricating properties at viscosities of

7.4 to 420 cSt (50 to 2000 ssu)Installation: No restrictions; See page 9.020.1Cavity: VC16-2; See page 9.116.1Cavity Tool: CT16-2XX; See page 8.600.1Seal Kit: SK16-2X-T; See page 8.650.1Coil Nut: Part No. 7004400;


USASI: ISO:

SYMBOLS


1.020.1

10.3/150

8.3/120

6.2/90

4.1/60

2.1/30

37.910

75.820

113.630

FLOW lpm/gpm

PR

ES

SU

RE

DR

OP

bar

/psi

➁ to ➀ — (e); ➀ to ➁ - - - (d)32 cSt/150 ssu oil at 40°C

151.440

SV16-20

DIMENSIONS

MATERIALS TO ORDER



Standard Coil: Weight: 0.27 kg.(0.60 lbs.); Unitized thermoplas-tic encapsulated, Class H hightemperature magnetwire;See page 3.200.1


1.020.2


SAE 12 12TSAE 16 16T


*BSP Body;U.K. Mfr. Only

OptionNone (Blank)


SV16-20__ - __ __ __ - __ - __ __ __ __ __


1.62

E-CoilViewStandard

Coil View

41.1

2.3860.4

0.4511.4

1.84DIA.

46.7

HYDRAFORCE®












VoltageStd. Coil



terminations only


SOLENOID VALVES

SV08-21 Poppet, 2-Way, Normally Open

DESCRIPTIONA solenoid-operated, 2-way, piloted, poppet-type, normally open, screw-in, hydrauliccartridge valve designed for low leakage in load-holding applications.

OPERATIONWhen de-energized, the SV08-21 allows flow from ➁ to ➀. Flow from ➀ to ➁ isseverely restricted in this mode. If the ➁ to ➀ path is required see model SV08-23,page 1.050.1.

When energized, the valve's poppet closes on its seat, blocking flow from ➁ to ➀. Inthis mode the cartridge will allow ➀ to ➁ flow after overcoming the solenoid force(requires 3.4 to 10.3 bar [50 to 150 psi]).

Operation of Manual Override Option: To override, push and hold override button.

FEATURES• Continuous-duty rated coil.• Hardened seat for long life and low leakage.• Optional coil voltages and terminations.• Efficient wet-armature construction.• Cartridges are voltage interchangeable.• Unitized, molded coil design.• Manual override option.• Optional waterproof E-Coils rated up to IP69K.• Industry common cavity.• Compact size.

RATINGSOperating Pressure: 207 bar (3000 psi)Flow: See Performance ChartInternal Leakage: 0.15 cc/minute (3 drops/minute) max. at 207 bar (3000 psi)Temperature: -40 to 120°C with standard Buna sealsCoil Duty Rating: Continuous from 85% to 115% of nominal voltageResponse Time: First indication of change of state with 100% voltage supplied at

80% of nominal flow rating: Energized: 50 msec.; De-energized: 16 msec.Initial Coil Current Draw at 20°C: Standard Coil: 1.2 amps at 12 VDC; 0.13 amps at

115 VAC (full wave rectified). E-Coil: 1.4 amps at 12 VDC; 0.7 amps at 24 VDCMinimum Pull-in Voltage: 85% of nominal at 207 bar (3000 psi)Filtration: See page 9.010.1Fluids: Mineral-based or synthetics with lubricating properties at viscosities of



SYMBOLS

USASI: ISO:


1.030.1

8.6/125

6.9/100

5.2/75

3.4/50

1.7/25

7.52

15.14

22.76

30.28

FLOW lpm/gpm

PR

ES

SU

RE

DR

OP

bar

/psi

37.910

to — (d); to - - - (e)32 cSt/150 ssu oil at 40°C

➁➁ ➀ ➀

SV08-21

DIMENSIONS

MATERIALS TO ORDER





SV08-21__ - __ __ __ - __ - __ __ __ __ __Cartridge: Weight: 0.09 kg.(0.20 lbs.); Steel with hardenedwork surfaces. Zinc-platedexposed surfaces; Buna NO-rings and back-up standard.




OptionNone (Blank)

Manual Overridewithout Knob P

Manual Overridewith Knob K

1.030.2

1.4035.6

2.2156.1

1.41

E-CoilView

DIA.35.8

StandardCoil View

HYDRAFORCE®












VoltageStd. Coil



terminations only


SOLENOID VALVES

SF08-21 Poppet, 2-Way, N.O., High Pressure

DESCRIPTIONA solenoid-operated, 2-way, piloted, poppet-type, normally open, screw-in, hydrauliccartridge valve designed for low leakage in higher pressure load-holding applications.

OPERATIONWhen de-energized, the SF08-21 allows flow from ➁ to ➀. Flow from ➀ to ➁ isseverely restricted in this mode. If the ➁ to ➀ path is required see model SF08-23,page 1.051.1.

When energized, the valve's poppet closes on its seat, blocking flow from ➁ to ➀. Inthis mode the cartridge will allow ➀ to ➁ flow after overcoming the solenoid force(requires 3.4 to 10.3 bar [50 to 150 psi]).

FEATURES• Continuous-duty rated coil.• Hardened seat for long life and low leakage.• Optional coil voltages and terminations.• Efficient wet-armature construction.• Cartridges are voltage interchangeable.• Unitized, molded coil design.• Optional waterproof E-Coils rated up to IP69K.• Industry common cavity.• Compact size.

RATINGSOperating Pressure: 345 bar (5000 psi)Flow: See Performance ChartInternal Leakage: 0.15 cc/minute (3 drops/minute) max. at 345 bar (5000 psi)Temperature: -40 to 120°C with standard polyurethane sealsCoil Duty Rating: Continuous from 85% to 115% of nominal voltageResponse Time: First indication of change of state with 100% voltage supplied at





SYMBOLS

USASI: ISO:

1.031.1

1

2

1

2


6.9/100

13.8/200

17.2/250

10.3/150

20.7/300

3.4/50

7.52

15.14

22.76

30.28

FLOW lpm/gpm

PR

ES

SU

RE

DR

OP

bar

/psi

37.910


➁➁ ➀ ➀

SF08-21

DIMENSIONS

1.031.2

1.4035.6

2.2156.1

1.41 DIA.35.8

StandardCoil View

E-CoilView

HYDRAFORCE®

MATERIALS


Ported Body: Weight: 0.54 kg.(1.2 lbs.); Steel, zinc-plated(code "S"); or Ductile Iron(code "D") standard, consultfactory for weight, dimensionsmay differ; rated to 345 bar(5000 psi); See page 8.008.1.



OptionNone (Blank)

SF08-21__ - __ __ __ - __ - __ __ __ __ __

TO ORDER

SealsPolyurethane P

(Std.)















VoltageStd. Coil



terminations only


SOLENOID VALVES


DESCRIPTIONA solenoid-operated, 2-way, piloted, poppet-type, normally open, screw-in, hydrauliccartridge valve designed for low leakage in load-holding applications.

OPERATIONWhen de-energized, the SV10-21 allows flow from ➁ to ➀. Flow from ➀ to ➁ isseverely restricted in this mode. If the ➀ to ➁ path is required, see model SV10-23,page 1.053.1.

When energized, the valve's poppet closes on its seat, blocking flow in the ➁ to ➀direction. In this mode the cartridge will allow ➀ to ➁ flow after overcoming thesolenoid force (requires 3.4 to 10.3 bar [50 to 150 psi]).

Operation of the Manual Override Option: To override, push and hold overridebutton.

FEATURES• Continuous duty-rated solenoid.• Hardened seat for long life and low leakage.• Optional coil voltages and terminations.• Efficient wet-armature construction.• Cartridges are voltage interchangeable.• Unitized, molded coil design.• Industry common cavity.• Manual override option.• Optional waterproof E-Coils rated up to IP69K.






USASI: ISO:

SYMBOLS


1.032.1

8.6/125

6.9/100

5.2/75

3.4/50

1.7/25

11.43

22.76

34.19

56.815

FLOW lpm/gpm

PR

ES

SU

RE

DR

OP

bar

/psi

45.412

68.118


➁➁ ➀ ➀

SV10-21

DIMENSIONS

OptionNone (Blank)

Screen SManual Override

without Knob PManual Override

with Knob K

1.032.2

1.6241.1

1.84DIA.

46.7

E-CoilView

StandardCoil View

2.8071.1

HYDRAFORCE®

MATERIALS TO ORDER





SV10-21__ - __ __ __ - __ - __ __ __ __ __


SAE 6 6TSAE 8 8T

1/4 in. BSP* 2B3/8 in. BSP* 3B1/2 in. BSP* 4B













VoltageStd. Coil



terminations only


HSV10-21 HyPerformanceTM Poppet, 2-Way, N.O.

DESCRIPTIONA solenoid-operated, 2-way, normally open, poppet-type, screw-in hydraulic cartridge valve, designed to function as a load holding or blocking valve in high pressure applications requiring low internal leakage.

OPERATIONWhen de-energized, the HSV10-21 allows flow from 2 to 1 while flow from 1 to 2 is severely restricted in this mode.When energized, the valve’s poppet closes on its seat, blocking flow from 2 to 1. In this mode the cartridge will allow 1 to 2 flow after overcoming the actuator and spring forces (see peformance graph).







at port 2.Coil Duty Rating: Continuous from 85% to 115% of nominal voltageInitial Coil Current Draw at 20°C: 1.7 amps at 12 VDC; 0.85 amps at 24 VDCTemperature: -54° to 107°C (-65° to 225°F) with Urethane sealsFiltration: See page 9.010.1 Fluids: Mineral-based or synthetics with lubricating properties at viscosities of


1.033.1

SYMBOL


SOLENOID VALVES

HYDRAFORCE.com®

8.6/125

10.3/150

12.1/175

13.8/200

15.5/225

6.9/100

5.2/75

3.4/50

1.7/25

18.95

37.910

56.815

FLOW lpm/gpm

PR

ES

SU

RE

DR

OP

bar

/psi

Port 2 to 1 de-energized ——Port 1 to 2 energized - - - -


75.720

RP



HSV10-21

DIMENSIONS

1.033.2

TO ORDER

HSV10-21__ - __ __ __ - __ - __ __ __ __ __

Option None (Blank)

Cartridge: Weight: 0.19 kg. (0.41 lbs.); Steel with hardened work surfaces. Zinc-plated exposed surfaces. Urethane O-rings without back-up standard.





MATERIALS

®HYDRAFORCE

HYDRAFORCE.com®







2.85


72.3

1.00ACROSS FLATS

25.41.3133.3

0.7519.11.50

38.1

1.6241.1

1.0025.4 2.43

61.7

1.84DIA.

46.7

2.0050.8

0.20


Holes (2)

5.11.6341.3

2.4361.7

TORQUE: 5 – 7 ft-lb.

TORQUE:75 – 85 ft-lb.

6.8 – 9.5 Nm

102 – 115 Nm

RP



SOLENOID VALVES


DESCRIPTIONA solenoid-operated, 2-way, normally open, poppet-type, screw-in hydraulic cartridgevalve, designed to function as a load holding or blocking valve in applicationsrequiring low internal leakage.

OPERATIONWhen energized, the SV12-21 acts as a check valve, allowing flow to pass from ➀ to➁, while blocking flow in the reverse direction.

When de-energized, the poppet lifts to open the ➁ to ➀ flow path after overcomingthe solenoid force (requires 3.4 to 10.3 bar [50 to 150 psi]). In this mode, flow from ➀to ➁ is severely restricted. If this path is required, see model SV12-23, page 1.054.1.


FEATURES• Continuous-duty rated solenoid.• Hardened seat for long life and low leakage.• Optional coil voltages and terminations.• Efficient wet-armature construction.• Cartridges are voltage interchangeable.• Unitized, molded coil design.• Manual override option.• Optional waterproof E-Coils rated up to IP69K.• Cost effective cavity.






USASI:


SYMBOLS

1.033.1

ISO:

10.3/150

8.3/120

6.2/90

4.1/60

2.1/30

37.910

75.820

113.630

FLOW lpm/gpm

PR

ES

SU

RE

DR

OP

bar

/psi


➁ ➀ ➀ ➁

SV12-21

DIMENSIONS

OptionsNone (Blank)



1.033.2


1.62

2.89

41.1

73.4

1.84 (46.7) DIA.

E-CoilView

StandardCoil View

HYDRAFORCE®

MATERIALS





TO ORDER

SV12-21 __ - __ __ __ - __ - __ __ __ __ __









ConnectorsER Deutsch DT04-2P







VoltageStd. Coil



terminations only


SOLENOID VALVES


DESCRIPTIONA solenoid-operated, 2-way, normally open, poppet-type, screw-in hydraulic cartridgevalve, designed to function as a load-holding or blocking valve in applicationsrequiring low internal leakage.

OPERATIONWhen de-energized, the SV16-21 poppet lifts to open the ➁ to ➀ flow path. In thismode, flow from ➀ to ➁ is severely restricted. If this path is required, see modelSV16-23, page 1.055.1.

When energized, the ➁ to ➀ flow path is closed. In this mode, the valve acts as acheck valve, allowing flow to pass from ➀ to ➁ after overcoming the solenoid force(requires 3.4 to 10.3 bar [50 to 500 psi]).


FEATURES• Continuous duty-rated solenoid.• Hardened seat for long life and low leakage.• Optional coil voltages and terminations.• Efficient wet-armature construction.• Cartridges are voltage interchangeable.• Unitized, molded coil design.• Industry common cavity.• Manual override option.• Optional waterproof E-Coils rated up to IP69K.


valve may be used at higher pressures; consult factory.Proof Pressure: 345 bar (5000 psi)Flow: See Performance ChartInternal Leakage: 0.15 cc/minute (3 drops/minute) max. at 207 bar (3000 psi)Temperature: -40 to 120°C with standard Buna sealsCoil Duty Rating: Continuous from 85% to 115% of nominal voltageInitial Coil Current Draw at 20°C: Standard Coil: 1.67 amps at 12 VDC; 0.18 amps




USASI: ISO:

SYMBOLS


1.034.1


➁➁ ➀ ➀

10.3/150

8.3/120

6.2/90

4.1/60

2.1/30

37.910

75.820

113.630

FLOW lpm/gpm

PR

ES

SU

RE

DR

OP

bar

/psi

151.440

SV16-21

DIMENSIONS

1.034.2

1.6241.1

2.8973.4

E-CoilView

1.84DIA.

46.7

Standard Coil View

HYDRAFORCE®

MATERIALS TO ORDER









SV16-21__ - __ __ __ - __ - __ __ __ __ __


OptionNone (Blank)

Manual Override Pwithout Knob

Manual Override Kwith Knob











VoltageStd. Coil



terminations only


SOLENOID VALVES

SL08-22 Low Flow, 2-Way, Normally Closed

DESCRIPTIONA solenoid-operated, 2-way, normally closed, direct-acting, needle-type, screw-inhydraulic cartridge valve, designed to function as a load-holding device for low flowcircuits requiring extremely low leakage.

OPERATIONWhen de-energized, the SL08-22 blocks flow from ➁ to ➀.

When energized, the needle point lifts to open the valve bidirectionally.



FEATURES• Continuous-duty rated solenoid.• Hardened seat for long life and low leakage.• Optional coil voltages and terminations.• Cartridges are voltage interchangeable.• Unitized, molded coil design.• Industry common cavity.• Manual override option.• Optional waterproof E-Coils rated up to IP69K.• Compact size.

RATINGSOperating Pressure: 207 bar (3000 psi)Internal Leakage: 0.05 cc/minute (1 drop/minute) max. at 207 bar (3000 psi)Temperature: -40 to 120°C with standard Buna sealsCoil Duty Rating: Continuous from 85% to 115% of nominal voltageResponse Time: First indication of change of state with 100% voltage supplied at

80% of nominal flow rating (➁ to ➀ direction):Energized: 22 msec.; De-energized: 40 msec.

Initial Coil Current Draw at 20°C: Standard Coil: 1.2 amps at 12 VDC; 0.13 amps at115 VAC (full wave rectified). E-Coil: 1.4 amps at 12 VDC; 0.7 amps at 24 VDC

Minimum Pull-in Voltage: 85% of nominal at 207 bar (3000 psi)Filtration: See page 9.010.1Fluids: Mineral-based or synthetics with lubricating properties at viscosities of



USASI:

SYMBOLS


1.040.1

ISO:

8.3/120

6.2/90

4.1/60

2.1/30

.760.2

1.510.4

FLOW lpm/gpm

PR

ES

SU

RE

DR

OP

bar

/psi

➁ to ➀ or ➀ to ➁ - - - (e)32 cSt/150 ssu oil at 40°C

OptionsNone (Blank)

Screen SManual Override M

SL08-22

DIMENSIONS





1.040.2

1.4035.6

1.8847.7

1.41 DIA.35.8

0.4310.9

StandardCoil View

E-CoilView

HYDRAFORCE®

MATERIALS TO ORDER

SL08-22__ - __ __ __ - __ - __ __ __ __ __Cartridge: Weight: 0.09 kg.(0.20 lbs.); Steel with hardenedwork surfaces. Zinc-platedexposed surfaces; Buna NO-rings and back-up standard.















VoltageStd. Coil



terminations only


SOLENOID VALVES


DESCRIPTIONA solenoid-operated, 2-way, normally closed, poppet-type, screw-in hydrauliccartridge valve, designed for low leakage blocking and load holding applications.

OPERATIONWhen de-energized, the SV08-22 acts as a check valve, allowing flow from ➀ to ➁,while blocking flow from ➁ to ➀.

When energized, the poppet lifts to open the ➁ to ➀ flow path. In this mode, bidirec-tional flow is allowed.



FEATURES• Continuous-duty rated solenoid.• Hardened seat for long life and low leakage.• Optional coil voltages and terminations.• Efficient wet-armature construction.• Cartridges are voltage interchangeable.• Manual override option.• Optional waterproof E-Coils rated up to IP69K.• Unitized, molded coil design.• Industry common cavity.• Compact size.

RATINGSOperating Pressure: 207 bar (3000 psi)Flow: See Performance ChartInternal Leakage: 0.15 cc/minute (3 drops/minute) max. at 207 bar (3000 psi)Temperature: -40 to 120°C with standard Buna sealsCoil Duty Rating: Continuous from 85% to 115% of nominal voltageInitial Coil Current Draw at 20°C: Standard Coil: 1.2 amps at 12 VDC; 0.13 amps at




SYMBOLS

USASI: ISO:


1.041.1

8.6/125

6.9/100

5.2/75

3.4/50

1.7/25

7.52

15.14

22.76

FLOW lpm/gpm

PR

ES

SU

RE

DR

OP

bar

/psi


30.28

➁ ➀ ➁➀

SV08-22

DIMENSIONS




*BSP BodyU.K. Mfr. Only

1.041.2

OptionNone (Blank)

Manual Override MScreen S

1.4035.6

1.8847.7

1.41 DIA.35.8

0.4310.9

StandardCoil View

E-CoilView

HYDRAFORCE®

MATERIALS TO ORDER
















VoltageStd. Coil



terminations only


SOLENOID VALVES

SF08-22 Poppet, 2-Way, N.C., High Pressure


OPERATIONWhen de-energized, the SF08-22 acts as a check valve, allowing flow from ➀ to ➁,while blocking flow from ➁ to ➀.When energized, the cartridge's poppet lifts to open the ➁ to ➀ flow path. In thismode, bidirectional flow is allowed.

FEATURES• Continuous-duty rated coil.• Hardened seat for long life and low leakage.• Optional coil voltages and terminations.• Cartridges are voltage interchangeable.• Unitized, molded coil design.• Optional waterproof E-Coils rated up to IP69K.• Industry common cavity.• Compact size.





SYMBOLS

USASI: ISO:


1.042.1

11.0/160

8.3/120

5.5/80

2.8/40

3.81

15.24

FLOW lpm/gpm

PR

ES

SU

RE

DR

OP

bar

/psi

➁ to ➀ — (e); ➀ to ➁ - - - (e);➀ to ➁ . . . . (d)

32 cSt/150 ssu oil at 40°C

19.05

13.8/200

7.62

11.43

22.86

SF08-22

DIMENSIONS

1.042.2

1.4035.6

1.8847.7

1.41 DIA.35.8

0.4310.9

StandardCoil View

E-CoilView

HYDRAFORCE®

MATERIALS





OptionNone (Blank)

ManualOverride M

SF08-22__ - __ __ __ - __ - __ __ __ __ __

TO ORDER

SealsPolyurethane P

(Std.)















VoltageStd. Coil



terminations only



DESCRIPTIONA solenoid-operated, 2-way, normally closed, poppet-type, screw-in hydraulic cartridge valve, designed for low leakage blocking and load holding applications.

OPERATIONWhen de-energized, the SV10-22 acts as a check valve, allowing flow to pass from 1 to 2, while blocking flow from 2 to 1. With the sensor option, the neutral sensor will signal ON or HIGH.When energized, the 2 to 1 flow path opens. In this mode, flow is also allowed from 1 to 2. With the sensor option, the neutral sensor will signal LOW or OFF.Operation of Manual Override Option: To override, push button in, twist counter-clockwise 180° and release. In this position, the valve will remain open.To return to normal operation, push button in, twist clockwise 180° and release. Override will be detented in this position.


RATINGSOperating Pressure: 207 bar (3000 psi)Proof Pressure: 350 bar (5075 psi)Flow: See Performance ChartInternal Leakage: 0.15 cc/minute (3 drops/minute) max. at 207 bar (3000 psi)Temperature: with standard Buna N seals: -40 to 100°C (-40° to 212°F);

with Fluorocarbon seals: -26 to 204°C (-15°F to 400°F);Sensor Option: -40°C to 110°C (-40°F to 230°F)





7.4 to 420 cSt (50 to 2000 sus); See Temperature and Oil Viscosity, page 9.060.1Installation: No restrictions; See page 9.020.1Cavity: VC10-2; See page 9.110.1Cavity Tool: CT10-2XX; See page 8.600.1Seal Kit: SK10-2X-T; See page 8.650.1Coil Nut: Part No. 7004400

SYMBOLS

1.044.1

Port 2 to 1 energized - - - - -Port 1 to 2 energized — - —

Port 1 to 2 de-energized ——32 cSt/150 sus oil at 40°C

8.6/125

6.9/100

5.2/75

3.4/50

1.7/25

11.43

22.76

34.19

45.412

FLOW lpm/gpm

PR

ES

SU

RE

DR

OP

bar

/psi

56.815


SOLENOID VALVES

HYDRAFORCE.com®

ISO: with Sensor:

34.5/500

27.6/400

20.7/300

13.8/200

6.9/100

FLOW lpm/gpm

PR

ES

SU

RE

DR

OP

bar

/psi

SV10-22 with SensorPort 2 to 1 energized - - - - -Port 1 to 2 energized — - —

Port 1 to 2 de-energized ——32 cSt/150 sus oil at 40°C

11.33

22.76

34.19

45.412


FLO

W

Vcc

SE

NS

OR

OU

TP

UT


0

0.3 lpm0.08 gpm

56.8 lpm15 gpm

11 14 50 100

VOUT


RP



DIMENSIONS

SV10-22

1.044.2

1.6241.1

1.84DIA.

46.7

0.4511.4

E-CoilView

StandardCoil View

2.3860.3

®HYDRAFORCE

HYDRAFORCE.com®


TO ORDER

SV10-(P)22(A)__ - __ __ __ - __ - __ __ __ __ __ - __ __

Option None (Blank)

Screen S Manual Override M Manual Override Y Manual Override J












terminations only


MATERIALS


Coil Termination E-Coil D-CoilDeutsch DT04-2P ER (IP69K) DR (IP65)Metri-Pack® 150 EY (IP69K) DY (IP65)Dual Lead Wires EL (IP69K) DL (IP65)Amp Jr. Timer EJ (IP67) —DIN 43650 EG (IP65) DG (IP65)Dual Spades — DS (IP65) Seals

N Buna N (Std.) V Fluorocarbon


Sensor Type 1 High to Low


RP




DESCRIPTIONA solenoid-operated, 2-way, normally closed, piloted, poppet-type, screw-in hydraulic cartridge valve, designed for load holding in high pressure applications requiring low internal leakage.

OPERATIONWhen de-energized, the HSV10-22 blocks flow from 2 to 1. In this mode the valve will allow flow from 1 to 2 after overcoming the spring forces. When energized, the valve will allow flow bi-directionally.Operation of Manual Override Option: For normal operation (de-energized) the manual override pin must be seated in the lower detent groove. To shift the valve manually, the operator pushes down on the knob and rotates 180° in either direction. When the manual override is actuated, increased flow can be achieved by pulling on the knob.







at port 2.Temperature: -54° to 107°C (-65° to 225°F) with Urethane sealsCoil Duty Rating: Continuous from 85% to 115% of nominal voltageResponse Time: First indication of change of state with 100% voltage supplied at



1.043.1

SYMBOL


SOLENOID VALVES

HYDRAFORCE.com®

10.3/150

12.4/180

14.5/210

16.6/240

8.3/120

6.2/90

4.1/60

2.1/30

18.95

37.910

56.815

FLOW lpm/gpm

PR

ES

SU

RE

DR

OP

bar

/psi

Port 2 to 1, energized ——Port 1 to 2, de-energized - - - -

Port 1 to 2, energized — —32 cSt/150 sus oil at 40°C

75.720


RP


HSV10-22

DIMENSIONS

1.043.2

TO ORDER

HSV10-22__ - __ __ __ - __ - __ __ __ __ __







MATERIALS

®HYDRAFORCE

HYDRAFORCE.com®






0.7519.11.50

38.1

1.0025.4 2.43

61.7

2.0050.8

0.20


Holes (2)

5.11.6341.3

2.4361.7

TORQUE:75 – 85 ft-lb.102 – 115 Nm

TORQUE: 5 – 7 ft-lb.6.8 – 9.5 Nm


2.54


64.5

18.3

1.00ACROSS FLATS

25.41.3133.3

1.6241.1

0.9223.4

0.72


RP


SOLENOID VALVES


DESCRIPTIONA solenoid-operated, 2-way, normally closed, poppet-type, screw-in hydrauliccartridge valve, designed to function as a load holding or blocking valve inapplications requiring low internal leakage.

OPERATIONWhen de-energized, the SV12-22 acts as a check valve, allowing flow to pass from➀ to ➁, while blocking flow in the reverse direction.

When energized, the poppet lifts to open the ➁ to ➀ flow path. In this mode, flow isalso allowed from ➀ to ➁.



FEATURES• Continuous-duty rated solenoid.• Hardened seat for long life and low leakage.• Optional coil voltages and terminations.• Efficient wet-armature construction.• Cartridges are voltage interchangeable.• Unitized, molded coil design.• Manual override option.• Optional waterproof E-Coils rated up to IP69K.• Cost effective cavity.






USASI: ISO:


SYMBOLS

1.045.1

10.3/150

8.3/120

6.2/90

4.1/60

2.1/30

37.910

75.820

113.630

FLOW lpm/gpm

PR

ES

SU

RE

DR

OP

bar

/psi

to — (e); to - - - (d); to . . . (e)


➁ ➀➀ ➁ ➀ ➁

SV12-22

DIMENSIONS

1.045.2


1.6241.1

1.84DIA.

46.7

0.4511.4

E-CoilView

StandardCoil View

2.3860.5

HYDRAFORCE®

MATERIALS





TO ORDER

SV12-22 __ - __ __ __ - __ - __ __ __ __ __

OptionsNone (Blank)


















VoltageStd. Coil



terminations only


SOLENOID VALVES


DESCRIPTIONA solenoid-operated, 2-way, normally closed, poppet-type, screw-in hydrauliccartridge valve, designed to function as a load-holding or blocking valve inapplications requiring low internal leakage.

OPERATIONWhen de-energized, the SV16-22 acts as a check valve, allowing flow from ➀ to ➁,while blocking flow from ➁ to ➀.

When energized, the poppet lifts to open the ➁ to ➀ flow path. In this mode, flow isalso allowed from ➀ to ➁.



FEATURES• Continuous-duty rated solenoid.• Hardened seat for long life and low leakage.• Optional coil voltages and terminations.• Efficient wet-armature construction.• Cartridges are voltage interchangeable.• Unitized, molded coil design.• Manual override option.• Optional waterproof E-Coils rated up to IP69K.• Industry common cavity.






SYMBOLS

USASI: ISO:


1.046.1

10.3/150

8.3/120

6.2/90

4.1/60

2.1/30

37.910

75.820

113.630

FLOW lpm/gpm

PR

ES

SU

RE

DR

OP

bar

/psi

151.440


➁ ➀ ➀ ➁

SV16-22

DIMENSIONS

1.046.2

1.62

E-CoilViewStandard

Coil View

41.1

2.3860.4

0.4511.4

1.84DIA.

46.7

HYDRAFORCE®

MATERIALS TO ORDER









OptionNone (Blank)


SV16-22__ - __ __ __ - __ - __ __ __ __ __













VoltageStd. Coil



terminations only


SOLENOID VALVES


DESCRIPTIONA solenoid-operated, 2-way, poppet-type, normally open, screw-in, hydraulic cartridgevalve designed for low leakage in load-holding applications.

OPERATIONWhen de-energized, the SV08-23 poppet lifts to open flow from ➁ to ➀. Flow is alsoopen from ➀ to ➁.

When energized, the cartridge acts as a check valve, allowing flow from ➀ to ➁,while blocking flow from ➁ to ➀ after overcoming the solenoid force (requires 3.4to 10.3 bar [50 to 150 psi]).


FEATURES• Continuous-duty rated solenoid.• Hardened seat for long life and low leakage.• Optional coil voltages and terminations.• Efficient wet-armature construction.• Cartridges are voltage interchangeable.• Unitized, molded coil design.• Manual override option.• Optional waterproof E-Coils rated up to IP69K.• Industry common cavity.• Compact size.






USASI: ISO:


SYMBOLS

1.050.1

8.6/125

6.9/100

5.2/75

3.4/50

1.7/25

7.52

15.14

22.76

30.28

FLOW lpm/gpm

PR

ES

SU

RE

DR

OP

bar

/psi


➁ ➀ ➀ ➁

SV08-23

DIMENSIONS

1.050.2

1.4035.6

2.2156.1

1.41

E-CoilView

DIA.35.8

StandardCoil View

HYDRAFORCE®

MATERIALS TO ORDER










OptionNone (Blank)



with Knob K











VoltageStd. Coil



terminations only


DESCRIPTIONA solenoid-operated, 2-way, normally open, poppet-type, screw-in hydraulic cartridgevalve, designed to function as a load holding or blocking valve in applicationsrequiring low internal leakage at high pressure.

OPERATIONWhen de-energized, the SF08-23 poppet lifts to open from ➁ to ➀. In this mode, flowis also allowed from ➀ to ➁.

When energized, the cartridge acts as a check valve, blocking flow from ➁ to ➀ afterovercoming the solenoid force (requires 3.4 to 10.3 bar [50 to 150 psi]).


FEATURES• Continuous-duty rated solenoid.• Hardened seat for long life and low leakage.• Optional coil voltages and terminations.• Efficient wet-armature construction.• Cartridges are voltage interchangeable.• Unitized, molded coil design.• Manual override option.• Optional waterproof E-Coils rated up to IP69K.• Industry common cavity.





SOLENOID VALVES

SF08-23 Poppet, 2-Way, Normally Open

SYMBOLS

USASI: ISO:


1.051.1

6.9/100

13.8/200

17.2/250

10.3/150

20.7/300

3.4/50

7.52

15.14

22.76

30.28

FLOW lpm/gpm

PR

ES

SU

RE

DR

OP

bar

/psi

37.910


➁➁ ➀ ➀

Note: This valve, the SF08-23, replaces the SV58-23 which is now obsolete.For more information consult factory.

SF08-23

DIMENSIONS

1.051.2

1.4035.6

2.2156.1

1.41 DIA.35.8

StandardCoil View

E-CoilView

HYDRAFORCE®

MATERIALS





OptionNone (Blank)

Screen S

SF08-23__ - __ __ __ - __ - __ __ __ __ __

TO ORDER

SealsPolyurethane P

(Std.)















VoltageStd. Coil



terminations only



DESCRIPTIONA solenoid-operated, two-way, poppet-type, normally open, screw-in, hydraulic cartridge valve.

OPERATIONWhen de-energized, the SV10-23 allows bidirectional flow from 2 to 1. With the sensor option, the neutral sensor will signal OFF or LOW.When energized, the valve’s poppet closes to block flow from 2 to 1. In this mode, the cartridge allows free reverse flow from 1 to 2 after overcoming the solenoid force (requires 3.4 to 10.3 bar / 50 to 150 psi). With the sensor option, the neutral sensor will signal ON or HIGH.Operation of Manual Override Option: To override, push and hold override button.


RATINGSOperating Pressure: 207 bar (3000 psi)Proof Pressure: 345 bar (5000 psi)Flow: See Performance ChartInternal Leakage: 0.15 cc/minute (3 drops/minute) max. at 207 bar (3000 psi)Temperature: with standard Buna N seals: -40 to 100°C (-40° to 212°F);






7.4 to 420 cSt (50 to 2000 sus); See Temperature and Oil Viscosity, page 9.060.1Installation: No restrictions; See page 9.020.1Cavity: VC10-2; See page 9.110.1; Cavity Tool: CT10-2XX; See page 8.600.1Seal Kit: SK10-2X-T; See page 8.650.1Coil Nut: Part No. 7004420

ISO: with Sensor:


SYMBOLS

1.053.1

8.6/125

6.9/100

5.2/75

3.4/50

1.7/25

11.43

22.76

34.19

56.815

FLOW lpm/gpm

PR

ES

SU

RE

DR

OP

bar

/psi

45.412

68.118

Port 2 to 1 De-energized ——Port 1 to 2 Energized - - - -32 cSt/150 sus oil at 40°C

SOLENOID VALVES

HYDRAFORCE.com®

34.5/500

27.6/400

20.7/300

13.8/200

6.9/100

FLOW lpm/gpm

PR

ES

SU

RE

DR

OP

bar

/psi

SV10-23 with SensorPort 2 to 1 Energized - - - - -Port 1 to 2 Energized — - —

Port 1 to 2 De-energized ——32 cSt/150 sus oil at 40°C

11.43

22.76

34.19

56.815

45.412


FLO

W

Vcc

SE

NS

OR

OU

TP

UT


0

0.3 lpm0.08 gpm

68.1 lpm18 gpm

70 7450 100

VOUT


RP



SV10-23

DIMENSIONS

1.053.2

1.6241.1

1.84DIA.

46.7

E-CoilView

StandardCoil View

2.8071.1

®HYDRAFORCE

HYDRAFORCE.com®


TO ORDER

SV10-(P)23(A)__ - __ __ __ - __ - __ __ __ __ __ - __ __

Option None (Blank)

152μ Screen S Manual Override P Manual Override K












terminations only


MATERIALS



Sensor Type 2 Low to High




RP



HSV10-23 HyPerformanceTM Poppet, 2-Way, Open

DESCRIPTIONA high pressure, solenoid operated, 2-way, piloted, poppet-type, normally open, screw-in hydraulic cartridge valve, designed for low leakage in load-holding applications.

OPERATIONWhen de-energized, the HSV10-23 allows flow bi-directionally. When energized, the valve's poppet closes on its seat, blocking flow from ports 2 to 1. In this mode, the cartridge will allow flow from ports 1 to 2 after overcoming the actuator and spring forces (see performance graph).







at port 2.Temperature: -54° to 107°C (-65° to 255° F) with Urethane seals.Coil Duty Rating: Continuous from 85% to 115% of nominal voltageResponse Time: First indication of change of state with 100% voltage supplied at

80% of nominal flow rating: Energized: 80 msec.; De-energized: 30 msec.Initial Coil Current Draw at 20°C: 1.7 amps at 12 VDC; 0.85 amps at 24 VDCMinimum Pull-in Voltage: 85% of nominal at 24 VDCFiltration: See page 9.010.1 Fluids: Mineral-based or synthetics with lubricating properties at viscosities of

7.4 to 420 cSt (50 to 2000 sus); See Temperature and Oil Viscosity, page 9.060.1Installation: No restrictions; See page 9.020.1Cavity: HVC10-2; See page 9.110.1Cavity Tool: HCT10-2xx; See page 8.600.1Seal Kit: SK10-2N-M ; See page 8.650.1Coil Nut: Part No. 4555250

1.053.3

SYMBOL


SOLENOID VALVES

HYDRAFORCE.com®

10.3/150

12.4/180

14.5/210

16.6/240

17.9/260

8.3/120

6.2/90

4.1/60

2.1/30

18.95

37.910

56.815

FLOW lpm/gpm

PR

ES

SU

RE

DR

OP

bar

/psi

75.720

Port 1 to 2, energized - - - -Port 1 to 2, de-energizedPort 2 to 1, de-energized —— 32 cSt/150 sus oil at 40°C

RP



HSV10-23

DIMENSIONS

1.053.4

TO ORDER

HSV10-23__ - __ __ __ - __ - __ __ __ __ __

Option None (Blank)





MATERIALS

®HYDRAFORCE

HYDRAFORCE.com®







2.95


75.0

ACROSS FLATS

1.3133.3

1.0626.9

0.7519.11.50

38.1

1.6241.1

1.0025.4 2.43

61.7

1.84DIA.

46.7

2.0050.8

0.20


Holes (2)

5.11.6341.3

2.4361.7



6.8 – 9.5 Nm

102 – 115 Nm


RP




DESCRIPTIONA solenoid-operated, two-way, normally open, poppet-type, screw-in hydraulic cartridge valve, designed to function as a load holding or blocking valve in applications requiring low internal leakage.

OPERATIONWhen de-energized, the SV12-23 allows bidirectional flow from 2 to 1. With the sensor option, the neutral sensor will signal OFF or LOW.When energized, the valve’s poppet closes to block flow from 2 to 1. In this mode, the cartridge allows free reverse flow from 1 to 2 after overcoming the solenoid force (requires 3.4 to 10.3 bar / 50 to 150 psi). With the sensor option, the neutral sensor will signal ON or HIGH.Operation of Manual Override Option: To override, push and hold override button.

FEATURES• Continuous-duty rated solenoid. • Unitized, molded coil design.• Hardened seat for long life and low leakage. • Manual override option.• Optional coil voltages and terminations. • Cost effective cavity.• Efficient wet-armature construction.• Cartridges are voltage interchangeable.• Optional waterproof E-Coils rated up to IP69K.

RATINGSOperating Pressure: 240 bar (3500 psi)Flow: See Performance ChartInternal Leakage: 0.15 cc/minute (3 drops/minute) max. at 240 bar (3500 psi)Temperature: with standard Buna N seals: -40 to 100°C (-40° to 212°F);






7.4 to 420 cSt (50 to 2000 sus); See Temperature and Oil Viscosity, page 9.060.1Installation: No restrictions; See page 9.020.1Cavity: VC12-2; See page 9.112.1Cavity Tool: CT12-2XX; See page 8.600.1Seal Kit: SK12-2X-T; See page 8.650.1Coil Nut: Part No. 7004420

ISO:


SYMBOLS

with Sensor:

1.054.1

10.3/150

8.3/120

6.2/90

4.1/60

2.1/30

37.910

75.820

113.630

FLOW lpm/gpm

PR

ES

SU

RE

DR

OP

bar

/psi

Port 2 to 1 De-energized ——Port 1 to 2 Energized - - - -32 cSt/150 sus oil at 40°C

SOLENOID VALVES

HYDRAFORCE.com®

20.7/300

13.8/200

17.2/250

10.3/150

6.9/100

3.4/50

15.94

30.38

45.412

60.616

75.720

FLOW lpm/gpm

PR

ES

SU

RE

DR

OP

bar

/psi

SV12-23 with SensorPort 2 to 1 Energized - - - - -Port 1 to 2 Energized — - —

Port 1 to 2 De-energized ——32 cSt/150 sus oil at 40°C

VALVE SHIFT %

FLO

W

Vcc

SE

NS

OR

OU

TP

UT


0

0.3 lpm0.08 gpm

75.7 lpm20 gpm

68 7350 100

VOUT


RP



SV12-23

DIMENSIONS

1.054.2


1.62

2.89

41.1

73.4

1.84 (46.7) DIA.

E-CoilView

StandardCoil View

®HYDRAFORCE

HYDRAFORCE.com®


TO ORDER

SV12-(P)23(A)__ - __ __ __ - __ - __ __ __ __ __ - __ __

Option None (Blank)

Manual Override P Manual Override K



Standard Ported Body: Weight: 0.57kg. (1.25 lbs.); Anodized high-strength 6061 T6 aluminum alloy, rated to 207 bar (3000 psi). Ductile iron bodies available; dimensions may differ. See page 8.012.1.



Porting Cartridge Only 0 SAE 6 10T SAE 8 12T SAE 16 16T 3/4 in. BSP* 6B 1 in. BSP* 8B*BSP Body; U.K. Mfr. Only






terminations only


MATERIALS



Sensor Type 2 Low to High




RP



SOLENOID VALVES


DESCRIPTIONA solenoid-operated, 2-way, normally open, poppet-type, screw-in hydraulic cartridgevalve, designed to function as a load holding or blocking valve in applicationsrequiring low internal leakage.

OPERATIONWhen de-energized, the SV16-23 poppet lifts to open the ➁ to ➀ flow path. In thismode, flow from ➀ to ➁ is also allowed.

When energized, the cartridge acts as a check valve, allowing flow to pass from ➀ to➁, while blocking flow in the reverse direction after overcoming the solenoid force(requires 3.4 to 10.3 bar [50 to 150 psi]).


FEATURES• Continuous-duty rated solenoid.• Hardened seat for long life and low leakage.• Optional coil voltages and terminations.• Efficient wet-armature construction.• Cartridges are voltage interchangeable.• Manual override option.• Optional waterproof E-Coils rated up to IP69K.• Unitized, molded coil design.• Industry common cavity.






USASI: ISO:

SYMBOLS


1.055.1


➁➁ ➀ ➀

10.3/150

8.3/120

6.2/90

4.1/60

2.1/30

37.910

75.820

113.630

FLOW lpm/gpm

PR

ES

SU

RE

DR

OP

bar

/psi

151.440

SV16-23

DIMENSIONS

1.055.2

1.6241.1

2.8973.4

E-CoilView

1.84DIA.

46.7

Standard Coil View

HYDRAFORCE®

MATERIALS TO ORDER









SV16-23__ - __ __ __ - __ - __ __ __ __ __


OptionNone (Blank)













VoltageStd. Coil



terminations only


SOLENOID VALVES

SV08-24 Spool, 2-Way, Normally Closed

DESCRIPTIONA solenoid-operated, 2-way, normally closed, direct-acting, spool-type, screw-inhydraulic cartridge valve, designed to operate as a bidirectional blocking valve in lowflow circuits.

OPERATIONWhen de-energized, the SV08-24 blocks flow in both directions.

When energized, the cartridge’s spool shifts to open the bidirectional flow path.

Operation of Manual Override Feature: To override, push button in and twistcounterclockwise 180°. The internal spring will push the button out. In this position,the valve may be only partially shifted. To assure full override shift, pull the button outto its fullest extension and hold it in this position.

FEATURES• Continuous-duty rated solenoid.• Hardened precision spool and cage for long life.• Optional coil voltages and terminations.• Both ports may be fully pressurized.• Efficient wet-armature construction.• Cartridges are voltage interchangeable.• Manual override option.• Optional waterproof E-Coils rated up to IP69K.• Unitized, molded coil design.• Industry common cavity.• Compact size.

RATINGSOperating Pressure: 207 bar (3000 psi)Flow: 17 lpm (4.5 gpm) max.Internal Leakage: 82 cc/minute (5 cu. in./minute) max. at 207 bar (3000 psi)Temperature: -40 to 120°C with standard Buna sealsCoil Duty Rating: Continuous from 85% to 115% of nominal voltageInitial Coil Current Draw at 20°C: Standard Coil: 1.2 amps at 12 VDC; 0.13 amps at


7.4 to 420 cSt (50 to 2000 ssu)Installation: No restrictions; See page 9.020.1Cavity: VC08-2; See page 9.108.1Cavity Tool: CT08-2XX; See page 8.600.1Seal Kit: SK08-2X-M; See page 8.650.1Coil Nut: Part No. 7004400;


To return to normal valve function, push button in, twist clockwise 180° and release.Override will be detented in this position.

USASI/ISO:


SYMBOLS

1.060.1

5.5/80

4.1/60

2.8/40

1.4/20

3.81

7.52

11.43

15.14

FLOW lpm/gpm

PR

ES

SU

RE

DR

OP

bar

/psi

Energized32 cSt/150 ssu oil at 40°C

18.95

6.9/100

SV08-24

DIMENSIONS

1.060.2

1.4035.6

1.8847.7

1.41 DIA.35.8

0.4310.9

StandardCoil View

E-CoilView

HYDRAFORCE®





OptionNone (Blank)


MATERIALS TO ORDER
















VoltageStd. Coil



terminations only


SOLENOID VALVES

DESCRIPTIONA solenoid-operated, 2-way, normally closed, direct-acting, spool-type, screw-inhydraulic cartridge valve, designed to operate as a bidirectional blocking valve.

OPERATIONWhen de-energized, the SV10-24 blocks flow in both directions.

When energized, the cartridge's spool shifts to open the bidirectional flow path.

Operation of Manual Override Option: To override, push button in and twistcounterclockwise 180°. The internal spring will push the button out. In this position,the valve may be only partially shifted. To assure full override shift, pull the button outto its fullest extension and hold it in this position.

FEATURES• Continuous-duty rated solenoid.• Hardened precision spool and cage for long life.• Optional coil voltages and terminations.• Both ports may be fully pressurized.• Efficient wet-armature construction.• Manual override option.• Optional waterproof E-Coils rated up to IP69K.• Unitized, molded coil design.• Industry common cavity.

RATINGSOperating Pressure: 207 bar (3000 psi)Proof Pressure: 350 bar (5075 psi)Flow: See Performance ChartInternal Leakage: 82 cc/minute (5 cu. in./minute) max. at 207 bar (3000 psi)Temperature: -40 to 120°C with standard Buna sealsCoil Duty Rating: Continuous from 85% to 115% of nominal voltageResponse Time: First indication of change of state with 100% voltage supplied at

80% of nominal flow rating:Energized: 30 msec.; De-energized: 25 msec.

Initial Coil Current Draw at 20°C: Standard Coil: 1.67 amps at 12 VDC; 0.18 ampsat 115 VAC (full wave rectified). E-Coil: 2.0 amps at 12 VDC; 1.0 amps at 24 VDC





To return to normal valve function, push button in, twist clockwise 180°, and release.Override will be detented in this position.

USASI/ISO:


SYMBOLS

1.064.1

6.9/100

5.5/80

4.1/60

2.8/40

1.4/20

15.14

30.28

60.616

FLOW lpm/gpm

PR

ES

SU

RE

DR

OP

bar

/psi

Energized32 cSt/150 ssu oil at 40°C

45.412

8.3/120

207/3000

172/2500

138/2000

69/1000

18.95

56.815

113.630

OPERATING FLOW lpm/gpm

OP

ER

AT

ING

PR

ES

SU

RE

bar

/psi

Performance Range (Shaded)

75.820

241/3500

35/500

103/1500

37.910

94.625

SV10-24

DIMENSIONS

1.064.2

1.6241.1

1.84DIA.

46.7

0.4511.4

E-CoilView

StandardCoil View

2.3860.3

HYDRAFORCE®

MATERIALS TO ORDER





SV10-24__ - __ __ __ - __ - __ __ __ __ __


SAE 6 6TSAE 8 8T



OptionNone (Blank)

Manual Override MManual Override YManual Override JFor Manual Override optionssee page 1.001.1












VoltageStd. Coil



terminations only


SOLENOID VALVES


DESCRIPTIONA solenoid-operated, 2-way, normally closed, direct-acting spool-type, screw-inhydraulic cartridge valve, designed to function as a bidirectional blocking valve.

OPERATIONWhen de-energized, the SV12-24 blocks flow in both directions. When energized, thevalve’s spool shifts to allow flow in both directions.

FEATURES• Continuous-duty rated solenoid.• Hardened spool and cage for long life.• Optional coil voltages and terminations.• All ports may be fully pressurized.• Heavy-duty water resistant E-Coils rated up to IP69K.

RATINGSOperating Pressure: 240 bar (3500 psi) max.Flow: See Performance ChartLeakage: 410 cc/minute (25 cu. in./minute) at 240 bar (3500 psi)Temperature: -40 to 120°C with Buna N sealsCoil Duty Rating: See ChartResponse Time: Pull-In: 100 msec; Drop-Out: 100 msecInitial Coil Current Draw at 20°C: 2.8 amps at 12 VDCFiltration: See page 9.010.1Fluids: Mineral-based or synthetics with lubricating properties at viscosities of

7.4 to 420 cSt (50 to 2000 ssu)Installation: No restrictions; See page 9.020.1Cavity: VC12-2; See page 9.112.1Cavity Tool: CT12-2XX; See page 8.600.1Seal Kit: SK12-2X-M; See page 8.650.1E-Coil Nut: Part No. 7085180

USASI/ISO:


SYMBOLS

1.065.1

2

1

13.8/200

10.3/150

6.9/100

3.4/50

37.910

18.95

56.815

75.820

FLOW lpm/gpm

PR

ES

SU

RE

DR

OP

bar

/psi

Inlet at ➀ — ; Inlet at ➁ - - -32 cSt/150 ssu oil at 40°C

276/4000

207/3000

138/2000

69/1000

37.910

18.95

56.815

75.820

94.725

FLOW lpm/gpm

PR

ES

SU

RE

bar

/psi

OPERATING LIMITSPull-In Current 85% of Nominal

Drop-Out Current 5% of NominalInlet at ➀: //// ; Inlet at ➁: \\\\

32 cSt/150 ssu oil at 40°C 110

120

60 7050403020100-20 -10-30-40

100

80

90

70

60

50% O

F R

AT

ED

VO

LTA

GE

AMBIENT TEMPERATURE (°C)

CONTINUOUS DUTY OPERATING RANGEMinimum Voltage at the Coil Required for Pull-In


Operating Range

SV12-24

DIMENSIONS

MATERIALS

Cartridge: Weight: 0.25 kg. (0.55 lbs.);Steel with hardened work surfaces.Zinc-plated exposed surfaces;Buna N O-rings and TFE back-upsstandard.


E-Coil: Weight: 1.36 kg. (3.0 lbs.);Fully encapsulated with ruggedexternal metal shell; Rated up toIP69K with integral connectors;See page 3.400.1.

TO ORDER

SV12-24 __ __ __ - __ - __ __ __ __ __




1.065.2



Voltage0 Less Coil

12 12 VDC24 24 VDC36 36 VDC48 48 VDC

MILLIMETRE2.19

HY

DR

AF

OR

CE

3.00

1.98

1.13

76.2

50.355.5

2.25

0.16 2.56

0.34

1.06

57.2

3.0076.2

1.25

ACROSS FLATS

TORQUE:55 ft-lbs.(40.6 Nm) max.

31.8

4.1 65.0

8.6

26.9

28.7

3.95100.3

1.8146.0

INCH

1.1027.9

1.7644.8

TORQUE:10 ft-lbs.

(13.5 Nm) max.

ACROSS FLATS31.81.25

2

1

2

1

Terminations (VDC)EL Leadwires (2), IP65 RatedES Dual Spades, IP65 RatedEG DIN 43650, IP65 RatedEW Leads w/Weather-Pack®

Connector, IP65 RatedEY Metri-Pack® 150 Connector,

IP69K Rated

HYDRAFORCE®


Other coil voltages may be availablefor OEM applications. Consult factory.

DESCRIPTIONA solenoid-operated, 2-way, normally open, direct-acting, spool-type, screw-inhydraulic cartridge valve designed to function as a bidirectional blocking valve in lowflow circuits.

OPERATIONWhen de-energized, the SV08-25 allows flow in both directions.

When energized, the valve’s spool shifts to close bidirectionally.

Operation of Manual Override Option: To override, push button in and twistcounterclockwise 180°. The internal spring will push the button out. In this position, thevalve may be only partially shifted. To assure full override shift, pull the button out toits fullest extension and hold it in this position.


FEATURES• Hardened precision spool and cage for long life.• Optional coil voltages and terminations.• Efficient wet-armature construction.• Both ports may be fully pressurized.• Cartridges are voltage-interchangeable.• Manual override option.• Optional waterproof E-Coils rated up to IP69K.• Unitized molded coil design.• Compact size.

RATINGSOperating Pressure: 207 bar (3000 psi)Flow: 9.5 lpm (2.5 gpm) max.Internal Leakage: 82 cc/minute (5 cu. in./minute) max. at 207 bar (3000 psi)Temperature: -40 to 120°C with standard Buna sealsCoil Duty Rating: Continuous from 85% to 115% of nominal voltageInitial Coil Current Draw at 20°C: Standard Coil: 1.2 amps at 12 VDC; 0.13 amps at




SOLENOID VALVES

SV08-25 Spool, 2-Way, Normally Open

SYMBOLS

USASI/ISO:


1.070.1

8.6/125

6.9/100

5.2/75

3.4/50

1.7/25

3.81

7.52

11.43

FLOW lpm/gpm

PR

ES

SU

RE

DR

OP

bar

/psi

De-Energized32 cSt/150 ssu oil at 40°C

SV08-25

DIMENSIONS

1.070.2

1.4035.6

1.8847.7

1.41 DIA.35.8

0.4310.9

StandardCoil View

E-CoilView

HYDRAFORCE®





OptionNone (Blank)


MATERIALS TO ORDER
















VoltageStd. Coil



terminations only


SOLENOID VALVES


DESCRIPTIONA solenoid-operated, 2-way, normally open, direct-acting, spool-type, screw-inhydraulic cartridge valve, designed to function as a bidirectional blocking valve.


When energized, the cartridge’s spool shifts to close the bidirectional flow path.

FEATURES• Continuous-duty rated solenoid.• Hardened precision spool and cage for long life.• Optional coil voltages and terminations.• Both ports may be fully pressurized.• Efficient wet-armature construction.• Cartridges are voltage interchangeable.• Unitized, molded coil design.• Industry common cavity.

RATINGSOperating Pressure: See Performance ChartFlow: See Performance ChartInternal Leakage: 82 cc/minute (5 in.3/minute) max. at 207 bar (3000 psi)Temperature: -40 to 120°C with standard Buna sealsCoil Duty Rating: Continuous from 85% to 115% of nominal voltageInitial Coil Current Draw at 20°C: 1.2 amps at 12 VDC; 0.13 amps at 115 VAC

(full wave rectified)Minimum Pull-in Voltage: 85% of nominal at 207 bar (3000 psi)Filtration: See page 9.010.1Fluids: Mineral-based or synthetics with lubricating properties at viscosities of

7.4 to 420 cSt (50 to 2000 ssu)Installation: No restrictions; See page 9.020.1Cavity: VC10-2; See page 9.110.1Cavity Tool: CT10-2XX; See page 8.600.1Seal Kit: SK10-2X-M; See page 8.650.1Coil Nut: Part No. 7004400

USASI/ISO:


SYMBOLS

1.075.1

6.9/100

5.5/80

4.1/60

2.8/40

1.4/20

7.52

15.14

22.76

FLOW lpm/gpm

PR

ES

SU

RE

DR

OP

bar

/psi

De-energized32 cSt/150 ssu oil at 40°C

206.9/3000

172.4/2500

137.9/2000

103.4/1500

69.0/1000

7.52

15.14

22.76


OP

ER

AT

ING

PR

ES

SU

RE

bar

/psi

3.81

11.43

18.95

34.5/500

241.4/3500

Operating Limits➀ to ➁ —; ➁ to ➀ - - -

SV80-25

SV80-25__ - __ __ __ - __ - __ __ __ __ __

DIMENSIONS

MATERIALS TO ORDER

Voltage 0 Less Coil 10 10 VDC†

12 12 VDC 24 24 VDC 36 36 VDC 48 48 VDC 24 24 VAC115 115 VAC230 230 VAC†Available only with DS, DW or DL terminations

SealsN Buna N (Std.)V Fluorocarbon

Cartridge: Weight: 0.16 kg. (0.35 lbs.);Steel with hardened work surfaces.Zinc-plated exposed surfaces. BunaN O-rings and polyester elastomerback-ups standard.

Standard Ported Body: Weight:0.16 kg. (0.35 lbs.); Anodized high-strength 6061 T6 aluminum alloy,rated to 240 bar (3500 psi); See page8.010.1. Ductile iron and steel bodiesavailable; dimensions may differ;consult factory.


OptionNone (Blank)


SAE 6 6TSAE 8 8T



1.075.2

HYDRAFORCE®

Terminations (VDC)DS Dual SpadesDG DIN 43650DL Leadwires (2)

DL/W Leads w/Weatherpak


Terminations (VAC)AG DIN 43650AP 1/2 in. Conduit


SOLENOID VALVES


DESCRIPTIONA solenoid-operated, 2-way, normally open, direct-acting, spool-type, screw-inhydraulic cartridge valve, designed to function as a bidirectional blocking valve.


When energized, the cartridge's spool shifts to close the bidirectional flow path.



FEATURES• Continuous-duty rated solenoid.• Hardened precision spool and cage for long life.• Optional coil voltages and terminations.• Both ports may be fully pressurized.• Efficient wet-armature construction.• Cartridges are voltage interchangeable.• Manual override option.• Optional waterproof E-Coils rated up to IP69K.• Unitized, molded coil design.• Industry common cavity.

RATINGSOperating Pressure: 207 bar (3000 psi)Proof Pressure: 350 bar (5075 psi)Flow: Inlet at port ➀: 18.9 lpm (5 gpm) max; Inlet at port ➁: 22.7 lpm (6 gpm) max.Internal Leakage: 82 cc/minute (5 cu. in./minute) max. at 207 bar (3000 psi)Temperature: -40 to 120°C with standard Buna sealsCoil Duty Rating: Continuous from 85% to 115% of nominal voltageResponse Time: First indication of change of state with 100% voltage supplied at





USASI/ISO:

PERFORMANCE (Cartridge Only

SYMBOLS

1.076.1

6.9/100

5.5/80

4.1/60

2.8/40

1.4/20

7.52

15.14

22.76

FLOW lpm/gpm

PR

ES

SU

RE

DR

OP

bar

/psi

De-energized32 cSt/150 ssu oil at 40°C

SV10-25

DIMENSIONS

1.076.2

1.6241.1

1.84DIA.

46.7

0.4511.4

E-CoilView

StandardCoil View

2.3860.3

HYDRAFORCE®

MATERIALS TO ORDER





SV10-25__ - __ __ __ - __ - __ __ __ __ __


SAE 6 6TSAE 8 8T



OptionNone (Blank)













VoltageStd. Coil



terminations only


HSV10-25 HyPerformanceTM Spool, 2-Way, N.O.

DESCRIPTIONA solenoid-operated, 2-way, normally open, spool-type, screw-in hydraulic cartridge valve, designed to function as a bi-directional blocking valve in high pressure applications.

OPERATIONWhen de-energized, the HSV10-25 allows flow in both directions.When energized, the cartridge’s spool shifts to close the bidirectional flow path.

FEATURES• Continuous-duty rated solenoid.• Hardened precision spool and cage for long life.• Optional coil voltages and terminations.• Both ports may be fully pressurized.• Efficient wet-armature construction.• Cartridges are voltage interchangeable.• Waterproof E-Coils rated up to IP69K.• 1000-hour salt-spray rated solenoid tubes and coils.• Unitized, molded coil design.• All HyPerformance products are tested to the rigorous standards





Burst Pressure: 1380 bar (20,000 psi)Flow: Up to 30.3 lpm (8 gpm)Internal Leakage: 2 to 1 Direction: 131 ml/minute (8 cu. in./minute) max. at 350 bar

(5075 psi); 1 to 2 Direction: 279 ml/minute (17 cu. in./minute) at 350 bar (5075 psi)Temperature: -54° to 107°C (-65° to 225°F) with Urethane sealsCoil Duty Rating: Continuous from 85% to 115% of nominal voltageResponse Time: First indication of change of state with 100% voltage supplied at



USASI/ISO:

1.077.1

SYMBOLS


SOLENOID VALVES

HYDRAFORCE.com®

3.4/50

4.1/60

4.8/70

5.5/80

2.8/40

2.1/30

1.4/20

0.7/10

7.62

15.14

22.76

FLOW lpm/gpm

PR

ES

SU

RE

DR

OP

bar

/psi

Both Directions32 cSt/150 sus oil at 40°C

30.38


RP


HSV10-25

DIMENSIONS

1.017.2

TO ORDER

HSV10-25__ - __ __ __ - __ - __ __ __ __ __

Option

None (Blank)




Porting

Cartridge Only 0 SAE 8 8TD 1/2 in. BSP* 4BD*BSP Body; U.K. Mfr. Only


MATERIALS

®HYDRAFORCE

HYDRAFORCE.com®


For Coils with Zener Diode, add “/Z” to option code. For example: “ER/Z”. Not available on all models. See coil option info. on page 3.400.1.


Coil TerminationDeutsch DT04-2P ER (IP69K)Metri-Pak 150 EY (IP69K)Dual Lead Wires EL (IP69K)Amp Jr. Timer EJ (IP67)DIN 43650 EG (IP65)Recommended for pressures

above 241 bar (3500 psi).


2.8572.4

1.00ACROSS FLATS

25.41.31


TORQUE:75 – 85 ft-lb.33.3


0.7519.11.50

38.1

1.6241.1

1.0025.4 2.43

61.7

1.84DIA.

46.7

2.0050.8

0.20


Holes (2)

5.11.6341.3

2.4361.7

6.8 – 9.5 Nm

102 – 115 Nm


RP


SOLENOID VALVES


DESCRIPTIONA solenoid-operated, 2-way, normally open, direct-acting spool-type, screw-inhydraulic cartridge valve, designed to function as a bidirectional blocking valve.

OPERATIONWhen de-energized, the SV12-25 allows flow in both directions. When energized, thevalve’s spool shifts to block flow in both directions.

FEATURES• Continuous-duty rated solenoid.• Hardened spool and cage for long life.• Optional coil voltages and terminations.• All ports may be fully pressurized.• Heavy-duty water resistant E-Coils rated up to IP69K.

RATINGSOperating Pressure: 240 bar (3500 psi) max.Flow: See Performance ChartLeakage: 410 cc/minute (25 cu.in./minute) in the ➁ to ➀ direction,

574 cc/minute (35 cu.in./minute) in the ➀ to ➁ direction, at 240 bar (3500 psi)Temperature: -40 to 120°C with Buna N sealsCoil Duty Rating: See ChartResponse Time: Pull-In: 100 msec; Drop-Out: 100 msecInitial Coil Current Draw at 20°C: 2.8 amps at 12 VDCFiltration: See page 9.010.1Fluids: Mineral-based or synthetics with lubricating properties at viscosities of

7.4 to 420 cSt (50 to 2000 ssu)Installation: No restrictions; See page 9.020.1Cavity: VC12-2; See page 9.112.1Cavity Tool: CT12-2XX; See page 8.600.1Seal Kit: SK12-2X-M; See page 8.650.1E-Coil Nut: Part No. 7085180

USASI/ISO:


SYMBOLS

1.077.1

2

1

13.8/200

10.3/150

6.9/100

3.4/50

37.910

18.95

56.815

75.820

FLOW lpm/gpm

PR

ES

SU

RE

DR

OP

bar

/psi

Inlet at ➀ — ; Inlet at ➁ - - -32 cSt/150 ssu oil at 40°C

276/4000

207/3000

138/2000

69/1000

37.910

18.95

56.815

75.820

94.725

FLOW lpm/gpm

PR

ES

SU

RE

bar

/psi


Drop-Out Current 5% of NominalInlet at ➀: //// ; Inlet at ➁: \\\\

32 cSt/150 ssu oil at 40°C110

120

60 7050403020100-20 -10-30-40

100

80

90

70

60

50% O

F R

AT

ED

VO

LTA

GE




Operating Range

SV12-25

DIMENSIONS

MATERIALS



Coil: Weight: 1.36 kg. (3.0 lbs.);External Metal Shell, Class H hightemperature magnet-wire; See page3.400.1.

TO ORDER

SV12-25 __ __ __ - __ - __ __ __ __ __




1.077.2



MILLIMETRE2.19

HY

DR

AF

OR

CE

3.00

1.98

1.13

76.2

50.355.5

2.25

0.16 2.56

0.34

1.06

57.2

3.0076.2

1.25

ACROSS FLATS


31.8

4.1 65.0

8.6

26.9

28.7

3.95100.3

1.8146.0

INCH

1.1027.9

1.7644.8

TORQUE:10 ft-lbs.

(13.5 Nm) max.


2

1

2

1

Voltage0 Less Coil12 12 VDC24 24 VDC36 36 VDC48 48 VDC

HYDRAFORCE®



IP69K Rated



SOLENOID VALVES

SV08-26 Blocking/Low Flow, 2-Way, Normally Closed

DESCRIPTIONA solenoid-operated, 2-way, normally closed, direct-acting, needle-type, screw-inhydraulic cartridge valve, designed to function as a blocking or load-holding device forlow flow circuits.

OPERATIONWhen de-energized, the SV08-26 blocks flow in both directions, to pressure rating. Ifpressure on ➀ exceeds the rating, flow may pass from ➀ to ➁.

When energized, the needle point lifts to open the valve bidirectionally. Port ➁ is therecommended load-holding port.



FEATURES• Continuous-duty rated solenoid.• Hardened seat for long life and low leakage.• Optional coil voltages and terminations.• Cartridges are voltage interchangeable.• Unitized, molded coil design.• Industry common cavity.• Manual override option.• Optional waterproof E-Coils rated up to IP69K.• Compact size.

RATINGSOperating Pressure: 207 bar (3000 psi)Effective Orifice Size: 0.81 mm (0.032 in.)Internal Leakage: 0.10 cc/minute (3 drops/minute) max. at 207 bar (3000 psi)Temperature: -40 to 120°C with standard Buna sealsCoil Duty Rating: Continuous from 85% to 115% of nominal voltageResponse Time: First indication of change of state with 100% voltage supplied at

80% of nominal flow rating (➁ to ➀ direction):Energized: 16 msec.; De-energized: 10 msec.

Initial Coil Current Draw at 20°C: Standard Coil: 1.2 amps at 12 VDC; 0.13 amps at115 VAC (full wave rectified). E-Coil: 1.4 amps at 12 VDC; 0.7 amps at 24 VDC




USASI/ISO:

SYMBOLS


1.080.1

34.5/500

27.6/400

20.7/300

13.8/200

0.950.25

1.890.50

FLOW lpm/gpm

PR

ES

SU

RE

DR

OP

bar

/psi

6.9/100

to or to - - - (e)32 cSt/150 ssu oil at 40°C➁ ➀ ➀ ➁

SV08-26

DIMENSIONS

1.080.2

1.4035.6

1.8847.7

1.41 DIA.35.8

0.4310.9

StandardCoil View

E-CoilView

HYDRAFORCE®





OptionNone (Blank)


MATERIALS TO ORDER
















VoltageStd. Coil



terminations only


SOLENOID VALVES

SV38-26 Blocking/Low Flow, 2-Way, Normally Closed

USASI/ISO:


SYMBOLS

1.081.1

DESCRIPTIONA solenoid-operated, 2-way, normally closed, direct-acting, needle-type, screw-inhydraulic cartridge valve, designed to function as a blocking or load-holding device forlow flow circuits.

OPERATIONWhen de-energized, the SV38-26 blocks flow in both directions, to pressure rating. Ifpressure on ➀ exceeds the rating, flow may pass from ➀ to ➁.

When energized, the needle point lifts to open the valve bidirectionally. Port ➁ is therecommended load-holding port.

Operation of Manual Override Option: To override, push button in, twist counter-clockwise 180° and release. In ths position, the valve will remain open.

To return to normal operation, push button in, twist clockwise 180° and release.Override will be detented in this position

FEATURES• Continuous-duty rated solenoid.• Hardened seat for long life and low leakage.• Optional coil voltages and terminations.• Cartridges are voltage interchangeable.• Unitized, molded coil design.• Industry common cavity.• Manual override option.• Optional waterproof E-Coils rated up to IP69K.

RATINGSOperating Pressure: 207 bar (3000 psi)Proof Pressure: 520 bar (7540 psi)Internal Leakage: 0.10 cc/minute (2 drops/minute) max. at 207 bar (3000 psi)Temperature: -40 to 120°C with standard Buna sealsCoil Duty Rating: Continuous from 85% to 115% of nominal voltageResponse Time: First indication of change of state with 100% voltage supplied at





34.5/500

27.6/400

20.7/300

13.8/200

1.140.3

3.40.9

FLOW lpm/gpm

PR

ES

SU

RE

DR

OP

bar

/psi

6.9/100

to or to - - - (e)32 cSt/150 ssu oil at 40°C➁ ➀ ➀ ➁

2.30.6

SV38-26

DIMENSIONS

1.081.2

1.6241.1

1.84DIA.

46.7

E-CoilViewStd. Coil

View2.4562.2

HYDRAFORCE®

MATERIALS TO ORDER

Cartridge: Weight: 0.15 kg.(0.33 lbs.); Steel with hardenedwork surfaces. Zinc-platedexposed surfaces. Buna NO-rings and back-ups standard.




SV38-26__ - __ __ __ - __ - __ __ __ __ __


*BSP Body; U.K. Mfrs. Only




OptionsNone (Blank)

Screen SManual Override MManual Override YManual Override JFor Manual Override optionssee page 1.001.1











VoltageStd. Coil



terminations only


SOLENOID VALVES

USASI/ISO:

SYMBOLS

1.090.1

SV38-28 Poppet, 2-Way, N.C., Bi-Directional Blocking


1

2

27.6/400

20.7/300

6.9/100

13.8/200

3.81

7.52

11.43

15.14

FLOW lpm/gpm

PR

ES

SU

RE

DR

OP

bar

/psi

18.95

➀ to ➁ or ➁ to ➀32 cSt/150 ssu oil at 40°C

1

2

DESCRIPTIONA solenoid-operated, 2-way, normally closed, poppet-type, bi-directional blocking,screw-in hydraulic cartridge valve, designed for low leakage in load-holding applica-tions.

OPERATIONWhen de-energized, the SV38-28 blocks flow in both directions. When energized, thevalve’s poppet opens on its seat, allowing flow from ➁ to ➀ and ➀ to ➁.

Consult factory if used serially with orifice disc.


FEATURES• Continuous-duty rated coil.• Hardened seat for long life and low leakage.• Optional coil voltages and terminations.• Efficient wet-armature construction.• Cartridges are voltage interchangeable.• Unitized, molded coil design.• Manual override option.• Optional waterproof E-Coils rated up to IP69K.• Industry common cavity.

RATINGSOperating Pressure: 207 bar (3000 psi)Flow: See Performance ChartInternal Leakage: 0.25 cc/minute (5 drops/minute) max. at 207 bar (3000 psi)Cycle Life: 500,000 cycles minimum at rated pressure

(due to internal dynamic seal life)Temperature: -40 to 100°C with standard Buna N sealsCoil Duty Rating: Continuous from 85% to 115% of nominal voltageInitial Coil Current Draw at 20°C: Standard Coil: 1.67 amps at 12 VDC; 0.18 amps


7.4 to 420 cSt (50 to 2000 ssu)Installation: No restrictions; See page 9.020.1Cavity: VC08-2; See page 9.108.1Cavity Tool: CT08-2XX; See page 8.600.1Seal Kit: SK08-2x-M; See page 8.650.1Coil Nut: Part No. 7004420;


SV38-28

DIMENSIONS

1.090.2

1

2

1.2531.8ACROSS FLATS

MILLIMETREINCH

TORQUE: 20 ft-lbs (27.1 Nm) max.

1

2

0.7318.5

MANUALOVERRIDEOPTION "K"

Ø1.0025.4


1.2531.8

1.84 DIA.46.7

0.7519.1

1.6241.1

2.0050.8

0.8722.1

1.4837.6

0.5614.2

2.9574.9

1.0927.7

MANUALOVERRIDEOPTION "P"

TORQUE: 5 ft-lbs (6.8 Nm) max.

2.9274.2

2.0050.8*

1.5038.1

1.6241.1

0.133.3

0.287.1

0.6015.2

* BSP BODY: 55.9 mm

E-CoilView

StandardCoil View

HYDRAFORCE®

OptionNone (Blank)



with Knob K

MATERIALS TO ORDER





SV38-28__ - __ __ __ - __ - __ __ __ __ __
















VoltageStd. Coil



terminations only


SOLENOID VALVES

USASI/ISO:

SYMBOLS

1.095.1



1

2

6.9/100

10.3/150

13.8/200

17.2/250

3.4/50

15.14

30.38

45.412

60.616

FLOW lpm/gpm

PR

ES

SU

RE

DR

OP

bar

/psi

➀ to ➁ ——; ➁ to ➀ - - - -32 cSt/150 sus oil at 40°C

75.720

DESCRIPTIONA solenoid-operated, 2-way, normally closed, internally piloted, poppet-type,bi-directional blocking, screw-in hydraulic cartridge valve, designed for low leakagein load-holding applications.

OPERATIONWhen de-energized, the SV10-28 blocks flow in both directions. When energized, thevalve’s poppet opens on its seat, allowing flow from ➁ to ➀ or ➀ to ➁.

FEATURES• Continuous-duty rated coil.• Optional coil voltages and terminations.• Cartridges are voltage interchangeable.• Optional waterproof E-Coils rated up to IP69K.• Hardened seat for long life and low leakage.• Industry common cavity.

RATINGSOperating Pressure: 240 bar (3500 psi)Flow: 75.7 lpm (20 gpm)Internal Leakage: 0.25 cc/minute (5 drops/minute) max. at 240 bar (3500 psi)Temperature: -40 to 120°C with standard Buna sealsCoil Duty Rating: Continuous from 85% to 115% of nominal voltageResponse Time: First indication of change of state with 100% voltage supplied at





SV10-28

DIMENSIONS

1.095.2

HYDRAFORCE®

1.6241.1

1.84DIA.

46.7

E-CoilView

StandardCoil View

TORQUE5–7 ft-lbs

6.8–9.5 Nm

TORQUE24–26 ft-lbs32.5–35.3 Nm

MATERIALS TO ORDER




E-Coil: Weight: 0.41 kg. (0.90 oz.);Fully encapsulated with ruggedexternal metal shell; Rated up toIP69K with integral connectors;Note: See page 3.400.1 for allE-Coil retrofit applications.

SV10-28 - __ __ __ - __ - __ __ __ __ __


SAE 6 6TSAE 8 8T














VoltageStd. Coil



terminations only



DESCRIPTIONA solenoid-operated, 2-way, piloted, normally closed, poppet-type, bi-directional, screw-in hydraulic cartridge valve, designed to function as a load holding or blocking valve in high pressure applications requiring low internal leakage bi-directionally.

OPERATIONWhen energized, the HSV10-28 allows flow in both directions. When de-energized, the valve blocks flow in both directions.Operation of Manual Override Option: For normal operation (de-energized) the manual override pin must be seated in the lower detent groove. To shift the valve manually, the operator pushes down on the knob and rotates 180° in either direction. When the manual override is actuated, increased flow can be achieved by pulling on the knob.






Burst Pressure: 1380 bar (20,000 psi)Flow: Up to 75.7 lpm (20 gpm)Internal Leakage: 0.25 cc/minute (5 drops/minute) max. at 350 bar (5075 psi)Temperature: -54° to 107°C (-65° to 225°F) with Urethane sealsCoil Duty Rating: Continuous from 85% to 115% of nominal voltageInitial Coil Current Draw at 20°C: 1.7 amps at 12 VDC; 0.85 amps at 24 VDCMinimum Pull-in Voltage: 85% of nominal at 207 bar (3000 psi)Filtration: See page 9.010.1 Fluids: Mineral-based or synthetics with lubricating properties at viscosities of


1.093.1

SYMBOL


SOLENOID VALVES

HYDRAFORCE.com®

1

2

8.6/125

10.3/150

12.1/175

13.8/200

15.5/225

6.9/100

5.2/75

3.4/50

1.7/25

18.95

37.910

56.815

FLOW lpm/gpm

PR

ES

SU

RE

DR

OP

bar

/psi

Port 1 to 2 - - - -; Port 2 to 1 ——32 cSt/150 sus oil at 40°C

75.720

RP



HSV10-28

DIMENSIONS

1.093.2

TO ORDER

HSV10-28__ - __ __ __ - __ - __ __ __ __ __







MATERIALS

®HYDRAFORCE

HYDRAFORCE.com®






0.7519.11.50

38.1

1.0025.4 2.43

61.7

2.0050.8

0.20


Holes (2)

5.11.6341.3

2.4361.7

TORQUE:75 – 85 ft-lb.102 – 115 Nm

TORQUE: 5 – 7 ft-lb.6.8 – 9.5 Nm


2.54


64.5

18.3

1.00ACROSS FLATS

25.41.3133.3

1.6241.1

0.9223.4

0.72

RP



SOLENOID VALVES

USASI/ISO:

SYMBOLS

1.097.1



1

2

DESCRIPTIONA solenoid-operated, 2-way, normally closed, internally piloted, poppet-type,bi-directional blocking, screw-in hydraulic cartridge valve, designed for low leakagein load-holding applications.

OPERATIONWhen de-energized, the SV12-28 blocks flow in both directions. When energized, thevalve’s poppet opens on its seat, allowing flow from ➁ to ➀ or ➀ to ➁.

FEATURES• Continuous-duty rated coil.• Optional coil voltages and terminations.• Efficient wet-armature construction.• Manual Override option.• Cartridges are voltage interchangeable.• Optional waterproof E-Coils rated up to IP69K.• Hardened seat for long life and low leakage.• Unitized, molded coil design.• Cost-effective cavity.

RATINGSOperating Pressure: 240 bar (3500 psi)Flow: 113.6 lpm (30 gpm)Internal Leakage: 7 drops per minute maximum at 240 bar (3500 psi)Temperature: -40 to 120°C with standard Buna sealsCoil Duty Rating: Continuous from 85% to 115% of nominal voltageResponse Time: First indication of change of state with 100% voltage supplied at




For E-Coils manufactured prior to 1-1-04, see page 3.400.1 for coil nut info.5.5/80

6.9/100

8.3/120

9.7/140

4.1/60

2.8/40

1.4/20

22.76

45.412

68.118

90.824

FLOW lpm/gpm

PR

ES

SU

RE

DR

OP

bar

/psi

➀ to ➁ or ➁ to ➀32 cSt/150 sus oil at 40°C

113.630

SV12-28

DIMENSIONS

1.097.2

HYDRAFORCE®


1.6241.1

1.84DIA.

46.7

0.4511.4

E-CoilView

StandardCoil View

2.3860.5

MATERIALS





TO ORDER

SV12-28 __ - __ __ __ - __ - __ __ __ __ __

OptionsNone (Blank)


















VoltageStd. Coil



terminations only




1.096.1

SYMBOL

SOLENOID VALVES

HYDRAFORCE.com®

DESCRIPTIONA solenoid-operated, two-way, normally closed, internally piloted, poppet-type, bi-directional blocking, screw-in hydraulic cartridge valve, designed for low leakage in load-holding applications.

OPERATIONWhen de-energized, the SV20-28 blocks fl ow in both directions. When energized, the valve’s poppet opens on its seat, allowing fl ow from ➁ to ➀ or ➀ to ➁.

FEATURES• Continuous-duty rated coil.• Optional coil voltages and terminations.• Effi cient wet-armature construction.• Cartridges are voltage interchangeable.• Waterproof E-Coils rated up to IP69K.• Hardened seat for long life and low leakage.• Unitized, molded coil design.• Cost-effective cavity.

RATINGSOperating Pressure: 207 bar (3000 psi)Flow: Up to 303 lpm (80 gpm)Internal Leakage: 5 drops/minute max. at 207 bar (3000 psi)Operating Temperature: -40° to 100°C (-40° to 212° F) with standard Buna N seals

-26° to 204°C (-15° to 400°F) with Fluorocarbon sealsCoil Duty Rating: Continuous from 85% to 115% of nominal voltageInitial Coil Current Draw at 20°C: Standard D-Coil: 1.2 amps at 12 VDC;

E-Coil: 1.4 amps at 12 VDC; 0.7 amps at 24 VDCMinimum Pull-in Voltage: See Chart on this page.Filtration: See page 9.010.1 Fluids: Mineral-based or synthetics with lubricating properties at viscosities of

7.4 to 420 cSt (50 to 2000 sus); See Temperature and Oil Viscosity, page 9.060.1Installation: No restrictions; See page 9.020.1Cavity: VC20-2; See page 9.120.1Cavity Tool: CT20-2XX; See page 8.600.1Seal Kit: SK20-2x-M; See page 8.650.1E-Coil Nut: Part No. 7085180

1

2

5.5/80

4.1/60

2.8/40

1.4/20

3810

22760

18950

FLOW lpm/gpm

DIF

FE

RE

NT

IAL

PR

ES

SU

RE

bar

/psi


26570

6.9/100

8.3/120

9.7/140

7620

15140

11430

30380

1 to 2

2 to 1

110

120

60 7050403020100-20 -10-30-40

100

80

90

70

60

50% O

F R

ATE

D V

OLT

AG

E




Operating Range

RP



SV20-28

DIMENSIONS

1.096.2

®HYDRAFORCE

HYDRAFORCE.com®

MATERIALS

Cartridge: Weight: 0.65 kg. (1.43 lbs.); Steel with hardened work surfaces. Zinc-plated exposed surfaces; Buna N O-rings with polyester elastomer back-up standard.

Standard Ported Body: Weight: 1.71 kg. (3.8 lbs.) Anodized high-strength 6061 T6 aluminum alloy, rated to 207 bar (3000 psi). Ductile iron bodies are available; dimensions may differ. See page 8.020.1.

E-Coil: Weight: 1.36 kg. (3.0 lbs.) Fully encapsulated with rugged external metal shell. Rated up to IP69K with integral connectors. See page 3.400.1

SV20-28 - __ __ __ - __ - __ __ __ __ __

TO ORDER

Seals Buna N (Std.) N Fluorocarbon V

Porting Cartridge Only 0 SAE 16 16T SAE 20 20T

Note: This is a 20-size valve which fi ts into a 20-size cavity, but uses a 12-size coil.

Voltage 0 Less Coil 12 12 VDC 24 24 VDC 36 36 VDC 48 48 VDC

Terminations (VDC) EL Leadwires (2), IP65 Rated ES Dual Spades, IP65 Rated EG DIN 43650, IP65 Rated EW Leads w/Weather-Pack® Connector, IP65 Rated EY Metri-Pack® 150 Connector, IP69K Rated ER Deutsch DT04-2P Connector, IP69K Rated

Other coil voltages may be available for OEM applications. Consult factory.

1.88 DIA.

ACROSS FLATS47.6

3.8898.5

2.2557.2

TORQUE:65 to 75 ft-lbs88.4 to 102 Nm

TORQUE:7 to 10 ft-lbs9.4 to 13.4 Nm

4.00101.6

1.2832.5

3.6392.1

0.194.8

3.2582.6

4.00101.6

0.348.7

1.5639.6

1.5038.1

3.0076.2

2.1955.6

1.7744.9

12-SizeE-Coil

12-SizeE-Coil

HY

DR

AF

OR

CE

For EY or ER Coil with Zener Diode, add “/Z” to option code. For example: “EY/Z”. See coil option info. on pages 3.400.1

RP



HSV10-29 HyPerformanceTM Poppet, 2-Way, N.O.

DESCRIPTIONA solenoid-operated, 2-way, normally open, piloted, poppet-type, bi-directional screw-in hydraulic cartridge valve, designed to function as a load holding or blocking valve in high pressure applications requiring low internal leakage.

OPERATIONWhen de-energized, the HSV10-29 allows flow in both directions.When energized, the valve blocks flow in both directions.






Burst Pressure: 1380 bar (20,000 psi)Flow: Up to 75.7 lpm (20 gpm)Internal Leakage: 0.25 cc/minute (5 drops/minute) max. at 350 bar (5075 psi)Coil Duty Rating: Continuous from 85% to 115% of nominal voltageInitial Coil Current Draw at 20°C: 1.7 amps at 12 VDC; 0.85 amps at 24 VDCTemperature: -54° to 107°C (-65° to 225°F) with Urethane sealsFiltration: See page 9.010.1 Fluids: Mineral-based or synthetics with lubricating properties at viscosities of


1.098.3

SYMBOL


SOLENOID VALVES

HYDRAFORCE.com®

1

2

6.9/100

8.3/120

9.7/140

11.0/160

12.4/180

5.5/80

4.1/60

2.8/40

1.4/20

18.95

37.910

56.815

FLOW lpm/gpm

PR

ES

SU

RE

DR

OP

bar

/psi

Port 2 to 1 ——; Port 1 to 2 - - - -32 cSt/150 sus oil at 40°C

75.720


RP


HSV10-29

DIMENSIONS

1.098.4

TO ORDER

HSV10-29__ - __ __ __ - __ - __ __ __ __ __

Option None (Blank)






MATERIALS

®HYDRAFORCE

HYDRAFORCE.com®







2.85


72.3

1.00ACROSS FLATS

25.41.3133.3

0.7519.11.50

38.1

1.6241.1

1.0025.4 2.43

61.7

1.84DIA.

46.7

2.0050.8

0.20


Holes (2)

5.11.6341.3

2.4361.7



6.8 – 9.5 Nm

102 – 115 Nm


RP


SOLENOID VALVES

USASI:

SYMBOLS

1.098.1

SV12-29 Poppet, 2-Way, N.O., Bi-Directional Blocking


DESCRIPTIONA solenoid-operated, 2-way, normally open, internally piloted, poppet-type,bi-directional blocking, screw-in hydraulic cartridge valve, designed for low leakagein load-holding applications.

OPERATIONWhen de-energized, the SV12-29 allows flow in both directions. When energized, thevalve’s poppet closes on its seat, blocking flow from ➁ to ➀ or ➀ to ➁.

FEATURES• Continuous-duty rated coil.• Optional coil voltages and terminations.• Efficient wet-armature construction.• Manual Override option.• Cartridges are voltage interchangeable.• Optional waterproof E-Coils rated up to IP69K.• Hardened seat for long life and low leakage.• Unitized, molded coil design.• Cost-effective cavity.

RATINGSOperating Pressure: 240 bar (3500 psi)Flow: 113.6 lpm (30 gpm)Internal Leakage: 7 drops per minute maximum at 240 bar (3500 psi)Temperature: -40 to 120°C with standard Buna sealsCoil Duty Rating: Continuous from 85% to 115% of nominal voltageResponse Time: First indication of change of state with 100% voltage supplied at




For E-Coils manufactured prior to 1-1-04, see page 3.400.1 for coil nut info.6.2/90

8.3/120

10.3/150

4.1/60

2.1/30

22.76

45.412

68.118

90.824

FLOW lpm/gpm

PR

ES

SU

RE

DR

OP

bar

/psi

➀ to ➁ ————➁ to ➀ — — —


113.630

1

2

1

2

ISO:

SV12-29

DIMENSIONS

1.098.2

HYDRAFORCE®

MATERIALS





TO ORDER

SV12-29 __ - __ __ __ - __ - __ __ __ __ __
















VoltageStd. Coil



terminations only



1.62

2.89

41.1

73.4

1.84 (46.7) DIA.

E-CoilView

StandardCoil View

OptionsNone (Blank)



SOLENOID VALVES

SVCV08-20 Poppet, 2-Way, Normally Closed . . .

DESCRIPTIONA solenoid-operated, 2-way, pilot-operated, poppet-type, normally closed, screw-inhydraulic cartridge valve with outlet flow check, designed for low leakage in loadholding applications.

OPERATIONWhen de-energized, the SVCV08-20 blocks flow from ➁ to ➀ and from ➀ to ➁.When energized, the cartridge's poppet lifts to open the ➁ to ➀ flow path, whilecontinuing to block flow from ➀ to ➁.

The SVCV08-20 is designed to fit into the VC08-3 cavity with the normal inlet at cavityport ➂ (valve port ➁), the outlet at cavity port ➀ (valve port ➀), and cavity port ➁blocked. The pressure drop will be substantially higher if cavity port ➁ is selected asan alternate outlet port.

FEATURES• Continuous-duty rated coil.• Hardened seat for long life and low leakage.• Optional coil voltages and terminations.• Cartridges are voltage interchangeable.• Optional waterproof E-Coils rated up to IP69K.• Industry common cavity.• Compact size.

RATINGSOperating Pressure: 207 bar (3000 psi)Rated Flow: 22.7 lpm (6 gpm)

Reverse Flow Check Valve Spring: .69 bar (10 psi)Maximum Internal Leakage: ➁ to ➀: 5 drops/minute at 207 bar (3000 psi);

➀ to ➁: 10 drops/minute at 207 bar (3000 psi)

Temperature: -40 to 120°C with standard Buna sealsCoil Duty Rating: Continuous from 85% to 115% of nominal voltage

Response Time: First indication of change of state with 100% voltage supplied at80% of nominal flow rating:Energized: 40 msec.; De-energized: 46 msec.



Filtration: See page 9.010.1

Fluids: Mineral-based or synthetics with lubricating properties at viscosities of7.4 to 420 cSt (50 to 2000 sus)


Cavity: VC08-3; See page 9.108.1Cavity Tool: CT08-3XX; See page 8.600.1

Seal Kit: SK08-3X-M; See page 8.650.1

Coil Nut: Part No. 7004400

SYMBOLS

USASI: ISO:


1.115.1

8.6/125

6.9/100

5.2/75

3.4/50

1.7/25

11.43

7.62

3.81

15.14

18.95

FLOW lpm/gpm

PR

ES

SU

RE

DR

OP

bar

/psi

Valve: ➁ to ➀3-Way Cavity: ➂ to ➀ ——32 cSt/150 sus oil at 40°C

22.76

10.3/150

SVCV08-20

DIMENSIONS

MATERIALS




E-Coil: Weight: 0.14 kg. (0.3 lbs.);Perfect wound, fully encapsu-lated with rugged external metalshell; Rated up to IP69K withintegral connectors; See page3.400.1.

OptionNone (Blank)

SVCV08-20__ - __ __ __ - __ - __ __ __ __ __

TO ORDER

1.115.2


SAE 6 6TSAE 8 8T

1/4 in. BSP* 2B*BSP Body;

U.K. Mfr. Only

1.88

TORQUE4–5 ft-lb(5.4–6.8 Nm)

TORQUE19–21 ft-lb

(25.8–28.5 Nm)

47.81.8847.8

1.6341.3

E-CoilView

1.4035.6

1.41


DIA.35.8

Standard Coil View

Plugged

HYDRAFORCE®










(IP69K Rated)


VoltageStd. Coil



terminations only


with Outlet Flow Check

SOLENOID VALVES

SVCV08-21 Poppet, 2-Way, Normally Open . . .

DESCRIPTIONA solenoid-operated, 2-way, pilot-operated, poppet-type, normally open, screw-inhydraulic cartridge valve with outlet flow check, designed for low leakage in loadholding applications.

OPERATIONWhen energized, the SVCV08-21 blocks flow from ➁ to ➀ and from ➀ to ➁.When de-energized, the cartridge's poppet lifts to open the ➁ to ➀ flow path, whilecontinuing to block flow from ➀ to ➁.

The SVCV08-21 is designed to fit into the VC08-3 cavity with the normal inlet at cavityport ➂ (valve port ➁), the outlet at cavity port ➀ (valve port ➀), and cavity port ➁blocked.

FEATURES• Continuous-duty rated coil.• Hardened seat for long life and low leakage.• Optional coil voltages and terminations.• Cartridges are voltage interchangeable.• Optional waterproof E-Coils rated up to IP69K.• Industry common cavity.• Compact size.

RATINGSOperating Pressure: 207 bar (3000 psi)

Rated Flow: 22.7 lpm (6 gpm)Reverse Flow Check Valve Spring: 0.69 bar (10 psi)

Maximum Internal Leakage: ➁ to ➀: 5 drops/minute at 207 bar (3000 psi);➀ to ➁: 10 drops/minute at 207 bar (3000 psi)

Temperature: -40 to 120°C with standard Buna seals


80% of nominal flow rating:Energized: 40 msec.; De-energized: 46 msec.


Minimum Pull-in Voltage: 85% of nominal at 207 bar (3000 psi)Filtration: See page 9.010.1

Fluids: Mineral-based or synthetics with lubricating properties at viscosities of7.4 to 420 cSt (50 to 2000 sus)


Cavity: VC08-3; See page 9.108.1

Cavity Tool: CT08-3XX; See page 8.600.1Seal Kit: SK08-3X-M; See page 8.650.1

Coil Nut: Part No. 7004400

SYMBOLS

USASI: ISO:


1.125.1

5.2/75

4.1/60

3.1/45

2.1/30

1.0/15

11.43

7.62

3.81

15.14

18.95

FLOW lpm/gpm

PR

ES

SU

RE

DR

OP

bar

/psi

Valve: ➁ to ➀3-Way Cavity: ➂ to ➀


22.76

6.2/90

SVCV08-21

DIMENSIONS

MATERIALS




E-Coil: Weight: 0.14 kg. (0.3 lbs.);Perfect wound, fully encapsu-lated with rugged external metalshell; Rated up to IP69K withintegral connectors; See page3.400.1.

OptionNone (Blank)

SVCV08-21__ - __ __ __ - __ - __ __ __ __ __

TO ORDER

1.125.2


SAE 6 6TSAE 8 8T

1/4 in. BSP* 2B*BSP Body;

U.K. Mfr. Only

1.88


TORQUE19–21 ft-lb

(25.8–28.5 Nm)

47.81.8847.8

1.6341.3

E-CoilView

1.4035.6

1.41


DIA.35.8

Standard Coil View

Plugged

HYDRAFORCE®










(IP69K Rated)


VoltageStd. Coil



terminations only



DESCRIPTIONA solenoid-operated, 3-way, direct-acting, spool-type, screw-in hydraulic directionalvalve.

OPERATIONWhen de-energized, the SV08-30 allows flow from ➁ to ➀, while blocking flow at ➂.

When energized, the cartridge's spool shifts to open from ➂ to ➁, while blocking flowout ➀. While port ➀ may be fully pressurized, it is not intended to be used as the inlet.



FEATURES• Continuous-duty rated solenoid.• Hardened precision spool and cage for long life.• Optional coil voltages and terminations.• Efficient wet-armature construction.• Cartridges are voltage interchangeable.• All ports may be fully pressurized.• Manual override option.• Optional waterproof E-Coils rated up to IP69K.• Unitized, molded coil design.• Fully guided spool.• Compact size.

RATINGSOperating Pressure: 207 bar (3000 psi)Flow: See Performance ChartInternal Leakage: ➂ Port (De-energized): 82 cc/minute (5 cu. in./minute) max. at 207

bar (3000 psi); ➀ Port (Energized): 164 cc/minute (10 cu. in./minute) max. at 207bar (3000 psi)

Temperature: -40 to 120°C with standard Buna sealsCoil Duty Rating: Continuous from 85% to 115% of nominal voltageResponse Time: First indication of change of state with 100% voltage supplied at



7.4 to 420 cSt (50 to 2000 ssu)Installation: See Note on Dimension DrawingCavity: VC08-3, Variation “A”; See page 9.108.1Cavity Tool: CT08-3XX; See page 8.600.1Seal Kit: SK08-3X-MM; See page 8.650.1Coil Nut: Part No. 7004400;


SOLENOID VALVES

SV08-30 Spool, 3-Way

SYMBOLS

USASI/ISO:


1.300.1

6.9/100

5.2/75

3.4/50

1.7/25

3.81

7.52

15.14

FLOW lpm/gpm

PR

ES

SU

RE

DR

OP

bar

/psi


➁ ➀ ➁➂

11.43

8.6/125

SV08-30

DIMENSIONS

1.300.2

1.8847.8

E-CoilView

1.4035.6

1.41COIL MUST BE INSTALLEDWITH LETTERING UP

DIA.35.8

Standard Coil View

0.4310.9

HYDRAFORCE®

OptionNone (Blank)

Manual Override M

MATERIALS





SV08-30__ - __ __ __ - __ - __ __ __ __ __

TO ORDER



SAE 6 6T1/4 in. BSP* 2B












VoltageStd. Coil



terminations only


DESCRIPTIONA solenoid-operated, 3-way, direct-acting, spool-type, screw-in hydraulic directional valve designed for high pressure operation up to 345 bar (5000 psi).

OPERATIONWhen de-energized, the SV58-30 allows fl ow from ➁ to ➀ while blocking fl ow at ➂.When energized, the cartridge’s spool shifts to open from ➂ to ➁, while blocking fl ow out ➀.Note: Port ➀ must be connected to tank. Valve cannot withstand more than 276 bar (4000 psi) at the inlet of port ➀.

FEATURES• Continuous-duty rated solenoid.• Hardened precision spool and cage for long life.• Optional coil voltages and terminations.• Effi cient wet-armature construction.• Cartridges are voltage interchangeable.• Optional waterproof E-Coils rated up to IP69K.• Unitized, molded coil design.• Fully guided spool.• Compact size.

RATINGSOperating Pressure: 345 bar (5000 psi)Flow: See Performance ChartInternal Leakage:

Port ➂ (De-energized): 131 ml/minute (8 cu. in./minute) max. at 345 bar (5000 psi); Port ➀ (Energized): 279 ml/minute (17 cu. in./minute) max. at 345 bar (5000 psi)

Temperature: -40 to 120°C with standard Buna seals; -26 to 204°C with Fluorocarbon seals; -54 to 107°C with Polyurethane seals


80% of nominal fl ow rating: Energized: 22 msec.; De-energized: 12 msec.Initial Coil Current Draw at 20°C: Standard Coil: 1.2 amps at 12 VDC;

0.13 amps at 115 VAC (full wave rectifi ed); E-Coil: 1.4 amps at 12 VDC; 0.7 amps at 24 VDC


7.4 to 420 cSt (50 to 2000 sus); See Temperature and Oil Viscosity, page 9.060.1Installation: No restrictions; See page 9.020.1Cavity: VC08-3, Variation “A”; See page 9.108.1Cavity Tool: CT08-3XX; See page 8.600.1Seal Kit: SK58-3X-MM; See page 8.650.1Coil Nut: Part No. 7004400;


SV58-30 Spool, 3-Way, High Pressure

SYMBOLS

USASI/ISO:


1.303.1

6.9/100

5.2/75

3.4/50

1.7/25

3.81

7.52

15.14

FLOW lpm/gpm

PR

ES

SU

RE

DR

OP

bar

/psi

➁ to ➀ de-energized ——➂ to ➁ energized - - - -


11.43

8.6/125

SOLENOID VALVES

HYDRAFORCE.com®

11.4/3

7.6/2

3.8/1

691000

1382000

2073000

2764000

3485000

PRESSURE bar/psi

FLO

W lp

m/g

pm

Operating LimitsBased on: Pull-In current of 85% of nominal

Drop-Out Current of 5% of nominalInlet at Port 3: ShadedInlet at Port 1: Hatched

RP



SV58-30

DIMENSIONS

1.303.2

SV58-30__ - __ __ __ - __ - __ __ __ __ __

TO ORDER

Seals Buna N (Std.) N Fluorocarbon V Polyurethane P

Termination (VDC) Std. D-Coil DS Dual Spades DG DIN 43650 DL Leadwires (2) DL/W Leads w/Weatherpak®

Connectors DR Deutsch DT04-2P

Termination (VAC) Std. D-Coil AG DIN 43650 AP 1/2 in. Conduit

Termination (VDC) E-Coil EG DIN 43650 – IP65/IP67 EJ Amp Junior Timer – IP69K EL Leadwires (2) – IP69K ER Deutsch DT04-2P – IP69K EY Metri-Pack® 150 – IP69K

Coils with internal diode are available. Consult factory.

Note: This is an 08-size valve which fi ts an 08-size cavity, but uses a 10-size coil.

E-Coil 10 10 VDC 12 12 VDC 20 20 VDC 24 24 VDC


12 12 VDC 24 24 VDC 36 36 VDC 48 48 VDC 24 24 VAC 115 115 VAC 230 230 VAC**Includes Std. Coil Nut† DS, DG or DL

terminations only.

MATERIALS

Cartridge: Weight: 0.15 kg. (0.32 lbs.); Steel with hardened work surfaces. Zinc-plated exposed surfaces; Buna N O-rings and back-ups standard.

Standard Ported Body: Weight: 0.27 kg. (0.60 lbs.); Anodized high-strength 6061 T6 aluminum alloy, rated to 207 bar (3000 psi); Ductile iron bodies available; dimensions may differ. See page 8.008.1.

Standard Coil: Weight: 0.27 kg. (0.60 lbs.); Unitized thermoplastic encapsulated, Class H high temperature magnetwire. See page 3.200.1.

E-Coil: Weight: 0.41 kg. (0.9 lbs.); Perfect wound, fully encapsulated with rugged external metal shell; Rated up to IP69K with integral connectors. See page 3.400.1 for all E-Coil retrofi t applications.

Porting Cartridge Only 0 SAE 6 6T 1/4 in. BSP* 2B


Option None (Blank)

®HYDRAFORCE

HYDRAFORCE.com®

Polyurethane seals are required for operation over 241 bar/3500 psi).

31.8

1.6241.1

1.84DIA.

46.7

2.9574.92.95

74.9E-CoilView

StandardCoil View

1.6040.6

0.112.8

TORQUE4 – 5 ft-lbs(5.4 – 6.8 Nm)

TORQUE19 – 21 ft-lbs

(25.8 – 28.5 Nm)

RP



SOLENOID VALVES


DESCRIPTIONA solenoid-operated, 3-way, direct-acting, spool-type, screw-in hydraulic cartridgevalve.

OPERATIONWhen de-energized, the SV07-31 allows flow from ➁ to ➀, while blocking flow at ➂.When energized, the cartridge's spool shifts to open from ➀ to ➂, while blocking at ➁.

FEATURES• Continuous-duty rated solenoid.• Hardened precision spool and cage for long life.• Optional coil voltages and terminations.• Efficient wet-armature construction.• Cartridges are voltage interchangeable.• All ports may be fully pressurized.• Optional waterproof E-Coils rated up to IP69K.• Unitized molded coil design.• Compact size.

RATINGSOperating Pressure: 207 bar (3000 psi)Flow: See Performance ChartInternal Leakage: 41 cc/minute (2.5 cu. in./minute) max. at 207 bar (3000 psi)Temperature: -40 to 120°C with standard Buna sealsCoil Duty Rating: Continuous from 85% to 115% of nominal voltageInitial Coil Current Draw at 20°C: Standard Coil: 1.2 amps at 12 VDC; 0.13 amps at


7.4 to 420 cSt (50 to 2000 ssu)Installation: No restrictions; See page 9.020.1Cavity: VC07-3; See page 9.107.1Cavity Tool: CT07-3XX; See page 8.600.1Seal Kit: SK07-3X-MM; See page 8.650.1Standard Coil Nut: Part No. 7004400;


USASI/ISO:

SYMBOLS

1.350.1


15/217.5

20/290

10/145

5/72.5

2.53

61.59

82.11

FLOW lpm/gpm

PR

ES

SU

RE

DR

OP

bar

/psi


➁➀ ➂ ➀

41.06

SV07-31

DIMENSIONS

1.350.2

1.8847.7

E-CoilView

StandardCoil View

1.4035.6

1.41 DIA.35.8

HYDRAFORCE®

OptionNone (Blank)

MATERIALS




SV07-31__ - __ __ __ - __ - __ __ __ __ __

TO ORDER













VoltageStd. Coil



terminations only


SOLENOID VALVES


USASI/ISO:

SYMBOLS


1.360.1

8.6/125

6.9/100

5.2/75

3.4/50

1.7/25

3.81

7.52

11.43

FLOW lpm/gpm

PR

ES

SU

RE

DR

OP

bar

/psi


➁ ➀ ➂ ➀



When energized, the valve's spool shifts to open from ➀ to ➂, while blocking at ➁.



FEATURES• Continuous-duty rated solenoid.• Hardened precision spool and cage for long life.• Optional coil voltages and terminations.• Efficient wet-armature construction.• Cartridges are voltage interchangeable.• All ports may be fully pressurized.• Manual override option.• Optional waterproof E-Coils rated up to IP69K.• Unitized molded coil design.• Compact size.

RATINGSOperating Pressure: 207 bar (3000 psi)Flow: See Performance Chart; Note: Under certain operating conditions this valve

may be rated for higher flow. Consult factory.Internal Leakage: 82 cc/minute (5 cu. in./minute) max. at 207 bar (3000 psi)Temperature: -40 to 120°C with standard Buna sealsCoil Duty Rating: Continuous from 85% to 115% of nominal voltageResponse Time: First indication of change of state with 100% voltage supplied at



7.4 to 420 cSt (50 to 2000 ssu)Installation: No restrictions; See page 9.020.1Cavity: VC08-3; See page 9.108.1Cavity Tool: CT08-3XX; See page 8.600.1Seal Kit: SK08-3X-MM; See page 8.650.1Coil Nut: Part No. 7004400;


SV08-31

DIMENSIONS

1.360.2


Standard Coil View

1.6040.6

0.4310.9

1.8847.8

E-CoilView

1.4035.6

1.41 DIA.35.8

HYDRAFORCE®

OptionNone (Blank)

Manual Override M

MATERIALS





SV08-31__ - __ __ __ - __ - __ __ __ __ __

TO ORDER















VoltageStd. Coil



terminations only


SOLENOID VALVES

SV38-31J Spool, 3-Way


OPERATIONWhen de-energized, the SV38-31J allows flow from ➁ to ➀, while blocking flow at ➂.

When energized, the cartridge's spool shifts to open from ➀ to ➂, while blocking at ➁.



FEATURES• Continuous-duty rated solenoid.• Hardened precision spool and cage for long life.• Optional coil voltages and terminations.• Efficient wet-armature construction.• Cartridges are voltage interchangeable.• All ports may be fully pressurized.• Manual override option.• Optional waterproof E-Coils rated up to IP69K.• Unitized molded coil design.• Compact size.

RATINGSOperating Pressure: 207 bar (3000 psi)Flow: See Performance ChartInternal Leakage: 82 cc/minute (5 cu. in./minute) max. at 207 bar (3000 psi)Temperature: -40 to 120°C with standard Buna sealsCoil Duty Rating: Continuous from 85% to 115% of nominal voltageInitial Coil Current Draw at 20°C: Standard Coil: 1.67 amps at 12 VDC; 0.18 amps




USASI/ISO:

SYMBOLS


1.361.1

8.6/125

6.9/100

5.2/75

3.4/50

1.7/25

3.81

7.52

11.43

FLOW lpm/gpm

PR

ES

SU

RE

DR

OP

bar

/psi


➁ ➀ ➂ ➀

SV38-31J

DIMENSIONS

1.361.2


SAE 6 6TSAE 8 8T



OptionNone (Blank)

Cable Release YFor Cable Release info.see page 1.001.1

1.6241.1

1.84 DIA.46.7

E-CoilView

StandardCoil View

HYDRAFORCE®

MATERIALS

Cartridge: Weight: 0.10 kg.(0.22 lbs.); Steel with hardenedwork surfaces. Zinc-platedexposed surfaces; Buna NO-rings and polyester elastomerback-ups standard.




SV38-31J__ - __ __ __ - __ - __ __ __ __ __

TO ORDER












VoltageStd. Coil



terminations only




When energized, the valve shifts to open from ➀ to ➂, while blocking at ➁.



FEATURES• Continuous-duty rated solenoid.• Hardened precision spool and cage for long life.• Optional coil voltages and terminations.• Efficient wet-armature construction.• All ports may be fully pressurized.• Cartridges are voltage interchangeable.• Manual override option.• Optional waterproof E-Coils rated up to IP69K.• Unitized, molded coil design.• Industry common cavity.

RATINGSOperating Pressure: 207 bar (3000 psi)Proof Pressure: 350 bar (5075 psi)Flow: 22.7 lpm (6 gpm) max.Internal Leakage: 82 cc/minute (5 cu. in./minute) max. at 207 bar (3000 psi)Temperature: -40 to 120°C with standard Buna sealsCoil Duty Rating: Continuous from 85% to 115% of nominal voltageResponse Time: First indication of change of state with 100% voltage supplied at



7.4 to 420 cSt (50 to 2000 ssu)Installation: No restrictions; See page 9.020.1Cavity: VC10-3, See page 9.110.1Cavity Tool: CT10-3XX; See page 8.600.1Seal Kit: SK10-3X-MM; See page 8.650.1Coil Nut: Part No. 7004400;


SOLENOID VALVES


SYMBOLS

USASI/ISO:


1.368.1

8.6/125

6.9/100

5.2/75

3.4/50

1.7/25

7.52

15.14

22.76

FLOW lpm/gpm

PR

ES

SU

RE

DR

OP

bar

/psi


➀ ➂ ➁ ➀

138/2000

3.81

11.43

22.76


OP

ER

AT

ING

PR

ES

SU

RE

bar

/psi

Operating LimitsInlet at ➀ (Shaded);Inlet at ➂ or ➁ - - -

15.14

207/3000

69/1000

7.52

18.95

26.57

276/4000

SV10-31

DIMENSIONS

1.368.2

1.6241.1

1.84DIA.

46.7

E-CoilView

2.3860.4Standard

Coil View

0.4511.4

HYDRAFORCE®

MATERIALS TO ORDER





SV10-31__ - __ __ __ - __ - __ __ __ __ __


SAE 6 6TSAE 8 8T



OptionNone (Blank)













VoltageStd. Coil



terminations only


SOLENOID VALVES


DESCRIPTIONA solenoid-operated, 3-way, direct-acting spool-type, screw-in hydraulic cartridgevalve.

OPERATIONWhen de-energized, the SV12-31 allows flow between ➁ and ➀ while blocking flowat ➂. When energized, the spool shifts to allow flow between ➀ and ➂ while blockingflow at ➁.

FEATURES• Continuous-duty rated solenoid.• Hardened spool and cage for long life.• Optional coil voltages and terminations.• All ports may be fully pressurized.• Heavy-duty waterproof E-Coils rated up to IP69K.


7.4 to 420 cSt (50 to 2000 ssu)Installation: No restrictions; See page 9.020.1Cavity: VC12-3; See page 9.112.1Cavity Tool: CT12-3XX; See page 8.600.1Seal Kit: SK12-3X-MM; See page 8.650.1E-Coil Nut: Part No. 7085180

USASI/ISO:


SYMBOLS

1.369.1

2

1

3

13.8/200

10.3/150

6.9/100

3.4/50

37.910

18.95

56.815

FLOW lpm/gpm

PR

ES

SU

RE

DR

OP

bar

/psi

➂ to ➀ — ; ➁ to ➀ - - -32 cSt/150 ssu oil at 40°C

172/2500

207/3000

241/3500

138/2000

103/1500

69/1000

35/500

37.910

18.95

56.815

75.820

FLOW lpm/gpm

PR

ES

SU

RE

bar

/psi


Drop-Out Current 5% of NominalInlet at ➂: //// ; Inlet at ➀: \\\\


110

120

60 7050403020100-20 -10-30-40

100

80

90

70

60

50% O

F R

AT

ED

VO

LTA

GE




Operating Range

SV12-31

DIMENSIONS

MATERIALS




TO ORDER

SV12-31 __ __ __ - __ - __ __ __ __ __




1.369.2



MILLIMETRE

1.1027.9

1.7644.8

1.25

ACROSS FLATS


TORQUE:10 ft-lbs.

(13.5 Nm) max.

31.8

3.95100.3

2.7870.6

INCH

1.25

ACROSS FLATS31.8

2.19

HY

DR

AF

OR

CE

55.5

53.8

82.6

101.6

29.2

8.6

91.94.8

101.6

50.8

50.3

1.15

3.620.19

4.00

3.25

2.12

4.00

2.00

1.98

0.342

1

3

2

3

1

Voltage0 Less Coil

12 12 VDC24 24 VDC36 36 VDC48 48 VDC

HYDRAFORCE®



IP69K Rated



DESCRIPTIONA solenoid-operated, 3-way, direct-acting, spool-type, screw-in hydraulic directionalvalve.

OPERATIONWhen de-energized, the SV08-33 allows flow from ➂ to ➀, while blocking flow at ➁.

When energized, the cartridge's spool shifts to open from ➁ to ➀, while blocking at ➂.



FEATURES• Continuous-duty rated solenoid.• Hardened precision spool and cage for long life.• Optional coil voltages and terminations.• Efficient wet-armature construction.• Cartridges are voltage interchangeable.• All ports may be fully pressurized.• Manual override option.• Optional waterproof E-Coils rated up to IP69K.• Unitized, molded coil design.• Compact size.

RATINGSOperating Pressure: 207 bar (3000 psi)Flow: See Performance ChartInternal Leakage: 82 cc/minute (5 cu. in./minute) max. at 207 bar (3000 psi)Temperature: -40 to 120°C with standard Buna sealsCoil Duty Rating: Continuous from 85% to 115% of nominal voltageInitial Coil Current Draw at 20°C: Standard Coil: 1.2 amps at 12 VDC; 0.13 amps at




SOLENOID VALVES


SYMBOLS

USASI/ISO:


1.370.1

6.9/100

5.5/80

4.1/60

2.8/40

1.4/20

3.81

7.52

11.43

FLOW lpm/gpm

PR

ES

SU

RE

DR

OP

bar

/psi

➂ to ➀ — (d)32 cSt/150 ssu oil at 40°C

SV08-33

DIMENSIONS

1.370.2


Standard Coil View

1.6040.6

0.4310.9

1.8847.8

E-CoilView

1.4035.6

1.41 DIA.35.8

HYDRAFORCE®

OptionNone (Blank)

Manual Override M

MATERIALS





SV08-33__ - __ __ __ - __ - __ __ __ __ __

TO ORDER















VoltageStd. Coil



terminations only



OPERATIONWhen de-energized, the SV10-33 allows flow from ➂ to ➀, while blocking flow at ➁.

When energized, the cartridge's spool shifts to open from ➀ to ➁, while blocking at ➂.




RATINGSOperating Pressure: 207 bar (3000 psi)Proof Pressure: 350 bar (5075 psi)Flow: 18.9 lpm (5 gpm) max.Internal Leakage: 82 cc/minute (5 cu. in./minute) max. at 207 bar (3000 psi)Temperature: -40 to 120°C with standard Buna sealsCoil Duty Rating: Continuous from 85% to 115% of nominal voltageInitial Coil Current Draw at 20°C: Standard Coil: 1.67 amps at 12 VDC; 0.18 amps




SOLENOID VALVES


SYMBOLSUSASI/ISO:

1.372.1


➀ to ➁ — (e); ➂ to ➀ - - - (d)32 cSt/150 ssu oil at 40°C

8.6/125

6.9/100

5.2/75

3.4/50

1.7/25

7.52

15.14

18.95

FLOW lpm/gpm

PR

ES

SU

RE

DR

OP

bar

/psi

3.81

11.43

DIMENSIONS

SV10-33

1.372.2

1.6241.1

1.84DIA.

46.7

E-CoilView

2.3860.4Standard

Coil View

0.4511.4

HYDRAFORCE®

MATERIALS TO ORDER





SV10-33__ - __ __ __ - __ - __ __ __ __ __


SAE 6 6TSAE 8 8T



OptionNone (Blank)













VoltageStd. Coil



terminations only


SOLENOID VALVES


DESCRIPTIONA solenoid-operated, 3-way, direct-acting spool-type, screw-in hydraulic cartridgevalve, intended as a bidirectional blocking valve.

OPERATIONWhen de-energized, the SV12-33 allows flow between ➂ and ➀ while blocking flowat ➁. When energized, the spool shifts to allow flow between ➁ and ➀ while blockingflow at ➂.




USASI/ISO:


SYMBOLS

1.374.1

2

1

3

10.3/150

6.9/100

8.6/125

5.2/75

3.4/50

1.7/25

37.910

18.95

56.815

FLOW lpm/gpm

PR

ES

SU

RE

DR

OP

bar

/psi

➂ to ➀ or ➁ to ➀32 cSt/150 ssu oil at 40°C

276/4000

207/3000

138/2000

69/1000

37.910

18.95

56.815

75.820

FLOW lpm/gpm

PR

ES

SU

RE

bar

/psi


Drop-Out Current 5% of Nominal32 cSt/150 ssu oil at 40°C

Inlet at ➁ or ➀

110

120

60 7050403020100-20 -10-30-40

100

80

90

70

60

50% O

F R

AT

ED

VO

LTA

GE




Operating Range

SV12-33

DIMENSIONS

1.374.2

MILLIMETRE

1.1027.9

1.7644.8

1.25

ACROSS FLATS


TORQUE:10 ft-lbs.

(13.5 Nm) max.

31.8

3.95100.3

2.7870.6

INCH

1.25

ACROSS FLATS31.8

2.19

HY

DR

AF

OR

CE

55.5

53.8

82.6

101.6

29.2

8.6

91.94.8

101.6

50.8

50.3

1.15

3.620.19

4.00

3.25

2.12

4.00

2.00

1.98

0.342

1

3

2

3

1

HYDRAFORCE®

MATERIALS




TO ORDER

SV12-33 __ __ __ - __ - __ __ __ __ __






Voltage0 Less Coil

12 12 VDC24 24 VDC36 36 VDC48 48 VDC



IP69K Rated



SOLENOID VALVES


DESCRIPTIONA solenoid-operated, 2-position, 3-way, direct-acting, spool-type, screw-in hydrauliccartridge valve.

OPERATIONWhen de-energized, the SV07-34 blocks flow at ➂ while allowing flow from ➁ to ➀.When the coil is energized, flow is provided from ➁ to ➂, while blocking at ➀.






USASI/ISO:

SYMBOLS

1.376.1


PR

ES

SU

RE

DR

OP

bar

/psi 27.6/400

20.7/300

13.8/200

6.9/100

3.81.0

7.62.0

11.43.0

13.23.5

FLOW lpm/gpm


1.90.5

5.71.5

3–2

2–3

2–1

1–2

9.52.5

207/3000

138/2000

104/1500

172/2500

69/1000

34/500

3.81.0

1.90.5

FLOW lpm/gpm

PR

ES

SU

RE

bar

/psi

Performance RangeShaded: ➀ to ➁, ➁ to ➀, ➂ to ➁

Hatched: ➁ to ➂

7.62.0

5.71.5

11.43.0

13.23.5

9.52.5

SV07-34

DIMENSIONS

1.376.2

1.8847.7

E-CoilView

StandardCoil View

1.4035.6

1.41 DIA.35.8

HYDRAFORCE®

OptionNone (Blank)

MATERIALS




SV07-34__ - __ __ __ - __ - __ __ __ __ __

TO ORDER













VoltageStd. Coil



terminations only


SOLENOID VALVES


SYMBOLS


USASI/ISO:

1.380.1

PR

ES

SU

RE

DR

OP

bar

/psi 10.3/150

8.3/120

6.2/90

4.1/60

2.1/30

7.52

15.14

22.76

FLOW lpm/gpm

➁ to ➀ — (d); ➁ to ➂ - - - (e)32 cSt/150 ssu oil at 40°C

3.81

11.43

18.95



When energized, the valve's spool shifts to open from ➁ to ➂, while blocking at ➀.




RATINGSOperating Pressure: 207 bar (3000 psi)Proof Pressure: 350 bar (5075 psi)Flow: 22.7 lpm (6 gpm) max.; Note: Under certain operating conditions this valve may

be rated for higher flow. Consult factory.Internal Leakage: 115 cc/minute (7 cu. in./minute) max. at 207 bar (3000 psi)Temperature: -40 to 120°C with standard Buna sealsCoil Duty Rating: Continuous from 85% to 115% of nominal voltageResponse Time: First indication of change of state with 100% voltage supplied at





DIMENSIONS

SV10-34

1.380.2

1.6241.1

1.84DIA.

46.7

E-CoilView

2.3860.4Standard

Coil View

0.4511.4

HYDRAFORCE®

MATERIALS TO ORDER





SV10-34__ - __ __ __ - __ - __ __ __ __ __


SAE 6 6TSAE 8 8T



OptionNone (Blank)













VoltageStd. Coil



terminations only


SOLENOID VALVES


DESCRIPTIONA solenoid-operated, 3-way, direct-acting spool-type, screw-in hydraulic cartridgevalve.

OPERATIONWhen de-energized, the SV12-34 allows flow between ➁ and ➀, while blocking flowat ➂. When energized, the spool shifts to allow flow between ➁ and ➂, while blockingflow at ➀.




USASI/ISO:


SYMBOLS

1.382.1

2

1

3

13.8/200

10.3/150

6.9/100

3.4/50

37.910

18.95

56.815

FLOW lpm/gpm

PR

ES

SU

RE

DR

OP

bar

/psi

➁ to ➀ or ➂ to ➁32 cSt/150 ssu oil at 40°C

276/4000

207/3000

138/2000

69/1000

37.910

18.95

56.815

75.820

FLOW lpm/gpm

PR

ES

SU

RE

bar

/psi



Inlet at ➁ or ➂

110

120

60 7050403020100-20 -10-30-40

100

80

90

70

60

50% O

F R

AT

ED

VO

LTA

GE




Operating Range

SV12-34

DIMENSIONS

1.382.2

MILLIMETRE

1.1027.9

1.7644.8

1.25

ACROSS FLATS


TORQUE:10 ft-lbs.

(13.5 Nm) max.

31.8

3.95100.3

2.7870.6

INCH

1.25

ACROSS FLATS31.8

2.19

HY

DR

AF

OR

CE

55.5

53.8

82.6

101.6

29.2

8.6

91.94.8

101.6

50.8

50.3

1.15

3.620.19

4.00

3.25

2.12

4.00

2.00

1.98

0.342

1

3

2

3

1

HYDRAFORCE®

MATERIALS




TO ORDER

SV12-34 __ - __ __ __ - __ - __ __ __ __ __





Voltage0 Less Coil

12 12 VDC24 24 VDC36 36 VDC48 48 VDC


Connector, IP65 RatedEY Metri-Pack® 150

Connector, IP69K Rated

OptionNone (Blank)






SOLENOID VALVES


DESCRIPTIONA solenoid-operated, 2-position, 3-way, direct-acting, spool-type, screw-in hydrauliccartridge valve.

OPERATIONWhen de-energized, the SV07-35 blocks flow at ➀, while allowing flow from ➁ to ➂.When energized, the spool shifts to provide flow from ➁ to ➀, while blocking at ➂.






USASI/ISO:

SYMBOLS

1.386.1


13.8/200

10.3/150

17.2/250

6.9/100

3.4/50

1.90.5

7.62.0

11.43

9.52.5

FLOW lpm/gpm

PR

ES

SU

RE

DR

OP

bar

/psi


5.71.5

3.81.0

1–2Energized

2–3De-energized

SV07-35

DIMENSIONS

1.386.2

1.8847.7

E-CoilView

StandardCoil View

1.4035.6

1.41 DIA.35.8

HYDRAFORCE®

OptionNone (Blank)

MATERIALS




SV07-35__ - __ __ __ - __ - __ __ __ __ __

TO ORDER













VoltageStd. Coil



terminations only


DESCRIPTIONA solenoid-operated, 2-position, 3-way, bi-directional blocking, screw-in hydrauliccartridge valve. It is designed for low leakage in load-holding applications.

OPERATIONWhen de-energized, the SV38-38 blocks flow from ➂ to ➁ or ➁ to ➂.

When energized, flow is blocked from ➁ to ➀, or from ➀ to ➁.

FEATURES• Continuous-duty rated solenoid.• Hardened seat for long life and low leakage.• Optional coil voltages and terminations.• Efficient wet-armature construction.• Cartridges are voltage interchangeable.• Optional waterproof E-Coils rated up to IP69K.• Unitized, molded coil design.• Industry-common cavity.

RATINGSOperating Pressure: 207 bar (3000 psi)Flow: See Performance ChartInternal Leakage: 0.25 cc/minute (5 drops/minute) at 207 bar (3000 psi)Temperature: -40 to 120°C with standard Buna sealsCoil Duty Rating: Continuous from 85% to 115% of nominal voltageInitial Coil Current Draw at 20°C: Standard Coil: 1.67 amps at 12 VDC; 0.18 amps


7.4 to 420 cSt (50 to 2000 ssu)Installation: No Restrictions; See page 9.020.1Cavity: VC08-3; See page 9.108.1Cavity Tool: CT08-3XX; See page 8.600.1Seal Kit: SK08-3X-MM; See page 8.650.1Coil Nut: Part No. 7004420;


SOLENOID VALVES

SV38-38 Double Blocking, 2 Position, 3-Way, N.C.

SYMBOLS

USASI/ISO:


1.390.1

11.0/160

8.3/120

5.5/80

2.8/40

3.81

FLOW lpm/gpm

PR

ES

SU

RE

DR

OP

bar

/psi

32 cSt/150 ssu oil at 40°C13.8/200

7.62

11.43

207/3000

138/2000

69/1000

3.81

FLOW lpm/gpm

PR

ES

SU

RE

bar

/psi

Performance RangeShaded: Inlet at ➀, Load at ➁, Tank At ➂

Shaded: Inlet at Selector ValveHatched: Inlet at ➂, Load at ➁, Tank At ➀

7.62

11.43

SV38-38

DIMENSIONS

1.390.2

HYDRAFORCE®

TO ORDERMATERIALS





SV38-38__ - __ __ __ - __ - __ __ __ __ __





OptionNone (Blank)

31.8

1.6241.1

1.84DIA.

46.7

2.9574.92.95

74.9E-CoilView

StandardCoil View

1.6040.6











VoltageStd. Coil



terminations only


SOLENOID VALVES

SV08-40 Spool, 4-Way, 2-Position

DESCRIPTIONA solenoid-operated, 4-way, 2-position, direct-acting spool-type, screw-in hydrauliccartridge valve.

OPERATIONWhen de-energized, the SV08-40 flow paths are ➂ to ➁, and ➃ to ➀.When energized, the valve's spool shifts to open ➂ to ➃, and ➁ to ➀. All ports areopen at cross-over.

Operation of Manual Override Option: To override, push button in and twistcounterclockwise 180°. The internal spring will push the button out. In this position, thevalve may be only partially shifted. To assure full override shift, pull the button out toits fullest extension and hold it in this position.


FEATURES• Continuous-duty rated solenoid.• Hardened precision spool and cage for long life.• Optional coil voltages and terminations.• Efficient wet-armature construction.• All ports may be fully pressurized.• Cartridges are voltage-interchangeable.• Manual override option.• Optional waterproof E-Coils rated up to IP69K.• Unitized, molded coil design.• Compact size.



7.4 to 420 cSt (50 to 2000 ssu)Installation: No restrictions; See page 9.020.1Cavity: VC08-4; See page 9.108.1Cavity Tool: CT08-4XX; See page 8.600.1Seal Kit: SK08-4X-MMM; See page 8.650.1Coil Nut: Part No. 7004400;


SYMBOLSUSASI/ISO:


5.5/80

4.1/60

2.8/40

1.4/20

3.81

7.62

11.43

FLOW lpm/gpm

PR

ES

SU

RE

DR

OP

bar

/psi

to — ; to - - - (d)32 cSt/150 ssu oil at 40°C➂ ➁ ➃ ➀

1.400.1

TRANSITION:

SV08-40

DIMENSIONS

1.400.2

1.8847.7

E-CoilView

Standard Coil View

1.4035.6

1.41 DIA.35.8

0.4310.9

HYDRAFORCE®

OptionNone (Blank)

Manual Override M

MATERIALS





VoltageStd. Coil



terminations only

SV08-40__ - __ __ __ - __ - __ __ __ __ __

TO ORDER



SAE 6 6T1/4 in. BSP* 2B3/8 in. BSP* 3B













SV58-40 Spool, 4-Way, 2-Position, High Pressure

DESCRIPTIONA solenoid-operated, 4-way, 2-position, direct-acting spool-type, screw-in hydraulic cartridge valve designed for high pressure operation up to 345 bar (5000 psi).

OPERATIONWhen de-energized, the SV58-40 fl ow paths are ➂ to ➁, and ➃ to ➀.When energized, the valve’s spool shifts to open ➂ to ➃, and ➁ to ➀. All ports are open at cross-over.Note: Port ➀ must be connected to tank. Valve cannot withstand more than 276 bar (4000 psi) at the inlet of port ➀.

FEATURES• Continuous-duty rated solenoid.• Hardened precision spool and cage for long life.• Optional coil voltages and terminations.• Effi cient wet-armature construction.• Cartridges are voltage-interchangeable.• Optional waterproof E-Coils rated up to IP69K.• Unitized, molded coil design.• Compact size.

RATINGSOperating Pressure: 345 bar (5000 psi)Flow: See Performance ChartInternal Leakage: 180 ml/minute (11 cu. in./minute) max. at 345 bar (5000 psi)Temperature: -40 to 120°C with standard Buna seals;

-26 to 204°C with Fluorocarbon seals; -54 to 107°C with Polyurethane sealsCoil Duty Rating: Continuous from 85% to 115% of nominal voltageInitial Coil Current Draw at 20°C: Standard Coil: 1.67 amps at 12 VDC;

0.18 amps at 115 VAC (full wave rectifi ed). E-Coil: 1.7 amps at 12 VDC; 0.85 amps at 24 VDC


7.4 to 420 cSt (50 to 2000 sus); See Temperature and Oil Viscosity, page 9.060.1Installation: No restrictions; See page 9.020.1Cavity: VC08-4; See page 9.108.1Cavity Tool: CT08-4XX; See page 8.600.1Seal Kit: SK58-4X-MMM; See page 8.650.1Coil Nut: Part No. 7004400;


SYMBOLSUSASI/ISO:


1.402.1

TRANSITION:

SOLENOID VALVES

HYDRAFORCE.com®

5.5/80

4.1/60

2.8/40

1.4/20

2.1/30

3.4/50

3 to 2

4 to 1

3 to 4

2 to 1

4.8/70

6.2/90

0.7/10

3.81.0

5.71.5

1.90.5

7.62.0

9.52.5

11.43.0

FLOW lpm/gpm

PR

ES

SU

RE

bar

/psi

Pressure vs. Flow32 cSt/150 sus oil at 40°C

11.4/3

7.6/2

3.8/1

691000

1382000

2073000

2764000

3485000

PRESSURE bar/psi

FLO

W lp

m/g

pm

Operating LimitsBased on: Pull-In current of 85% of nominal

Drop-Out Current of 5% of nominalInlet at Port 3: ShadedInlet at Port 1: Hatched

RP



SV58-40

DIMENSIONS

1.402.2

®HYDRAFORCE

HYDRAFORCE.com®

SV58-40__ - __ __ __ - __ - __ __ __ __ __

TO ORDER





12 12 VDC 24 24 VDC 36 36 VDC 48 48 VDC 24 24 VAC 115 115 VAC 230 230 VAC**Includes Std. Coil Nut† DS, DG or DL

terminations only.

MATERIALS



Standard Coil: Weight: 0.27 kg. (0.60 lbs.); Unitized thermo-plastic encapsulated, Class H high temperature magnetwire. See page 3.200.1.

E-Coil: Weight: 0.41 kg. (0.9 lbs.); Fully encapsulated with rugged external metal shell. Rated up to IP69K with integral connec-tors. See page 3.400.1 for all E-Coil retrofi t applications.

Porting Cartridge Only 0 SAE 6 6T 1/4 in. BSP* 2B 3/8 in. BSP* 3B


Option None (Blank)

1.6241.1

1.84DIA.

46.7

2.5063.6

E-CoilView

StandardCoil View

31.8

TORQUE4 – 5 ft-lbs(5.4 – 6.8 Nm)

TORQUE19 – 21 ft-lbs

(25.8 – 28.5 Nm)

Polyurethane seals are required for operation over 241 bar/3500 psi).

Termination (VDC) Std. D-Coil DS Dual Spades DG DIN 43650 DL Leadwires (2) DL/W Leads w/Weatherpak®


Termination (VAC) Std. D-Coil AG DIN 43650 AP 1/2 in. Conduit

Termination (VDC) E-Coil EG DIN 43650 – IP65/IP67 EJ Amp Junior Timer – IP69K EL Leadwires (2) – IP69K ER Deutsch DT04-2P – IP69K EY Metri-Pack® 150 – IP69KNote: This is an 08-size valve which

fi ts an 08-size cavity, but uses a 10-size coil.

RP



SOLENOID VALVES


DESCRIPTIONA solenoid-operated, 4-way, 2-position, direct-acting, spool-type, screw-in hydrauliccartridge valve.

OPERATIONWhen de-energized, the SV10-40 allows flow from ➂ to ➁, as well as from ➃ to ➀.

When energized, the cartridge's spool shifts to open ➂ to ➃, and ➁ to ➀.




RATINGSOperating Pressure: 207 bar (3000 psi)Proof Pressure: 350 bar (5075 psi)Flow: 23 lpm (6 gpm) max.Internal Leakage: 82 cc/minute (5 cu. in./minute) max. at 207 bar (3000 psi)Temperature: -40 to 120°C with standard Buna sealsCoil Duty Rating: Continuous from 85% to 115% of nominal voltageInitial Coil Current Draw at 20°C: Standard Coil: 1.67 amps at 12 VDC; 0.18 amps




USASI/ISO:

SYMBOLS


1.407.1

8.6/125

6.9/100

5.2/75

3.4/50

1.7/25

7.52

15.14

22.76

FLOW lpm/gpm

PR

ES

SU

RE

DR

OP

bar

/psi

to — ; to - - -32 cSt/150 ssu oil at 40°C

➂ ➁ ➃ ➀

TRANSITION:

SV10-40

DIMENSIONS

1.407.2

1.6241.1

1.84DIA.

46.7

0.4511.4

E-CoilView

StandardCoil View

2.3860.3

HYDRAFORCE®

MATERIALS TO ORDER





SV10-40__ - __ __ __ - __ - __ __ __ __ __


SAE 6 6TSAE 8 8T



OptionNone (Blank)













VoltageStd. Coil


12 12 VDC 24 24 VDC 36 36 VDC 48 48 VDC 24 24 VAC115 115 VAC230 230 VAC**Includes Std. Coil Nut† DS, DW or DLterminations only


SV10-40A Spool, 4-Way, 2-Position

DESCRIPTIONA solenoid-operated, four-way, two-position, direct-acting, spool-type, screw-in hydraulic cartridge valve.

OPERATIONWhen de-energized, the SV10-40A allows fl ow from ➂ to ➁, as well as from ➃ to ➀. When energized, the cartridge’s spool shifts to open ➂ to ➃, and ➁ to ➀. All ports are closed at crossover.

FEATURES• Continuous-duty rated solenoid with unitized, molded coil design..• Hardened precision spool and cage for long life.• Optional coil voltages and terminations.• Effi cient wet-armature construction.• All ports may be fully pressurized.• Cartridges are voltage interchangeable.• Optional waterproof E-Coils rated up to IP69K.• Industry common cavity.

RATINGSOperating Pressure: 207 bar (3000 psi)Proof Pressure: 276 bar (4000 psi)Burst Pressure: 965 bar (14000 psi)Flow: 37.9 lpm (10 gpm) max.Internal Leakage: 164 cc/minute (10 cu. in./minute) max. at 207 bar (3000 psi);

Port 3 to port 1, de-energized, with ports 2 and 4 blocked.Temperature: -40° to 100°C (-40° to 212° F) with standard Buna N seals

-26° to 204°C (-15° to 400°F) with Fluorocarbon seals;-54° to 104°C (-65° to 225°F) with Polyurethane seals.

Coil Duty Rating: Continuous from 85% to 115% of nominal voltageInitial Coil Current Draw at 20°C: Standard Coil: 1.67 amps at 12 VDC;



7.4 to 420 cSt (50 to 2000 sus); See Temperature and Oil Viscosity, page 9.060.1Installation: No restrictions; See page 9.020.1Cavity: VC10-4; See page 9.110.1Cavity Tool: CT10-4XX; See page 8.600.1Seal Kit: SK10-4X-MMM; See page 8.650.1Coil Nut: without manual override: Part No. 7004400

USASI/ISO:

SYMBOLS


1.408.1

13.8/200

17.2/250

10.3/150

6.9/100

3.4/50

7.52

15.14

22.76

30.38

37.910

FLOW lpm/gpm

PR

ES

SU

RE

bar

/psi

3 to 2 De-Energized, 2 looped to 4 — - — -3 to 4 Energized, 4 looped to 2 ———4 to 1 De-Energized, 2 looped to 4 - - - - -2 to 1 Energized, 4 looped to 2 – – – –


VALVE NOT USED AS A SELECTOR

TRANSITION:

SOLENOID VALVES

HYDRAFORCE.com®

2073000

1382000

691000

18.95.0

9.52.5

28.47.5

37.910.0

FLOW lpm/gpm

PR

ES

SU

RE

bar

/psi


Drop-Out Current 5% of NominalInlet at Port 1; Port 3 to Tank ///Inlet at Port 3; Port 1 to Tank \\\

32 cSt/150 sus oil at 40°C207

3000

1382000

691000

15.14

7.62

22.76

30.38

FLOW lpm/gpm

PR

ES

SU

RE

bar

/psi


Drop-Out Current 5% of NominalValve used as a selector with inlet at port 3.

Independent load pressuresat ports 2 and 4, ports not looped.

SV10-40AY: ////SV10-40A and SV10-40AM: \\\\


RP



SV10-40A

DIMENSIONS

1.408.2

TORQUE:5 to 7 ft-lbs.6.8 to 9.5 Nm

TORQUE:24 to 26 ft-lbs.

32.5 to 35.3 Nm

1.6241.1

1.84DIA.

46.7

0.4511.4

E-CoilView

StandardCoil View

2.3860.3

®HYDRAFORCE

HYDRAFORCE.com®

TO ORDER

SV10-40A __ - __ __ __ - __ - __ __ __ __ __Cartridge: Weight: 0.18 kg. (0.40 lbs.); Steel with hardened work surfaces. Zinc-plated exposed surfaces. Buna N O-rings and polyester elastomer back-up standard.


Standard Coil: Weight: 0.27 kg. (0.60 lbs.); Unitized thermoplas-tic encapsulated, Class H high temperature magnetwire. See page 3.200.1.


Porting Cartridge Only 0 SAE 6 6T SAE 8 8T 1/4 in. BSP* 2B 3/8 in. BSP* 3B*BSP Body; U.K. Mfr. Only


MATERIALS

Voltage 0 Less Coil** 12 12 VDC 24 24 VDC


Coil Termination E-Coil D-CoilDeutsch DT04-2P ER (IP69K) DR (IP65)Metri-Pak 150 EY (IP69K) DY (IP65)Dual Lead Wires EL (IP69K) DL (IP65)Amp Jr. Timer EJ (IP67) —DIN 43650 EG (IP65) DG (IP65)Dual Spades — DS (IP65)

**Includes Coil Nut.For Manual Override optionssee page 1.001.1

Option None (Blank) Manual Override M Manual Override Y

RP



HSV10-40R HyPerformanceTM Spool, 4-Way, 2-Pos.

DESCRIPTIONA solenoid-operated, four-way, two-position, direct-acting, spool-type, screw-in hydraulic cartridge valve for applications requiring high pressure operation.

OPERATIONWhen de-energized, the HSV10-40R allows fl ow between ➁ and ➀, and between ➂ and ➃. When energized, the spool shifts to allow fl ow between ➂ and ➁, and between ➃ and ➀. Consult factory for applications where port ➃ will be used as the inlet.

FEATURES• Unitized, molded coil design, continuous-duty rated.• Hardened precision spool and cage for long life.• Waterproof E-Coils rated up to IP69K; optional voltages and terminations.• Effi cient wet-armature construction.• All ports may be fully pressurized.• Cartridges are voltage-interchangeable.• 1000-hour salt-spray rated solenoid tubes and coils.• All HyPerformance products are tested to the rigorous standards

of the NFPA specifi cation T2.6.1.• All HyPerformance valves are tested at a verifi cation level of 90%


RATINGSOperating Pressure: 350 bar (5075 psi); 10% cycle life: 420 bar (6090 psi)


Burst Pressure: 1380 bar (20,000 psi)Flow: 22.7 lpm (6 gpm) max.Max. Internal Leakage:

Port 3 to 1, De-energized: 245 ml/minute (15 cu. in./minute.) at 350 bar (5075 psi);Port 3 to 1, Energized: 164 ml/minute (10 cu. in./minute.) at 350 bar (5075 psi);Port 1 to 3, De-energized: 164 ml/minute (10 cu. in./minute.) at 350 bar (5075 psi);Port 1 to 3, Energized: 245 ml/minute (15 cu. in./minute.) at 350 bar (5075 psi)

Temperature: -54° to 107°C (-65° to 225°F) with Urethane seals.Coil Duty Rating: Continuous from 85% to 115% of nominal voltageInitial Coil Current Draw at 20°C: 1.7 amps at 12 VDC; 0.85 amps at 24 VDCFiltration: See page 9.010.1 Fluids: Mineral-based or synthetics with lubricating properties at viscosities of

7.4 to 420 cSt (50 to 2000 sus); See Temperature and Oil Viscosity, page 9.060.1Installation: No restrictions; See page 9.020.1Cavity: HVC10-4; See page 9.110.1Cavity Tool: HCT10-4XX; See page 8.600.1Seal Kit: SK10-4U-OOO; See page 8.650.1Coil Nut: Part No. 4555250

SYMBOL


1.409.1

SOLENOID VALVES

HYDRAFORCE.com®

2

3

4

1

6.9/100

5.5/80

4.1/60

2.8/40

1.4/20

3.81

7.62

11.33

15.14

18.95

22.76

FLOW lpm/gpm

PR

ES

SU

RE

DR

OP

bar

/psi

Port 2 to 1 - - - - -All Other Paths ———


RP



HSV10-40R

DIMENSIONS

1.409.2

®HYDRAFORCE

HYDRAFORCE.com®

TO ORDER

HSV10-40R - __ __ __ - __ - __ __ __ __ __Cartridge: Weight: 0.21 kg. (0.47 lbs.); Steel with hardened work surfaces. Zinc-plated exposed surfaces. Urethane O-rings without back-ups standard.

Ported Body: Ductile iron recom-mended for operating pressures above 207 bar (3000 psi). Consult Factory.



MATERIALS

Voltage 0 Less Coil** 12 12 VDC 24 24 VDC**Includes Coil Nut.

Porting Cartridge Only 0



PPDI Urethane sealsrecommended for pressures above 241 bar (3500 psi).

1.6241.1

1.84


DIA.46.7

2.85


72.4

1.06ACROSS FLATS

26.9

2.51

TORQUE: 5 – 7 ft-lb.6.8 – 9.5 Nm

TORQUE:75 – 85 ft-lb.102 – 115 Nm63.8

2

3

4

1

RP



SOLENOID VALVES

SV12-40R Spool, 2-Position, 4-Way

USASI/ISO:


SYMBOLS

1.410.1

2

1

3

4

10.3/150

6.9/100

8.6/125

3.4/50

5.2/75

1.7/25

37.910

18.95

56.815

FLOW lpm/gpm

PR

ES

SU

RE

DR

OP

bar

/psi

➁ to ➀ or ➃ to ➀ —➂ to ➁ or ➂ to ➃ - - -


276/4000

207/3000

138/2000

69/1000

37.910

18.95

56.815

75.820

FLOW lpm/gpm

PR

ES

SU

RE

bar

/psi



Inlet at ➂

110

120

60 7050403020100-20 -10-30-40

100

80

90

70

60

50% O

F R

AT

ED

VO

LTA

GE




Operating Range

TRANSITION:

DESCRIPTIONA solenoid-operated, 2-position, 4-way, direct-acting spool-type, screw-in hydrauliccartridge valve.

OPERATIONWhen de-energized, the SV12-40R allows flow from ➁ to ➀, and from ➂ to ➃. Whenenergized, the spool shifts to allow flow from ➂ to ➁, and from ➃ to ➀.

Note: Consult factory for applications where port ➀ will be used as an inlet.

FEATURES• Continuous-duty rated solenoid.• Hardened spool and cage for long life.• Optional coil voltages and terminations.• All ports may be fully pressurized.• Manual override option.• Heavy-duty waterproof E-Coils rated up to IP69K.


7.4 to 420 cSt (50 to 2000 ssu)Installation: No restrictions; See page 9.020.1Cavity: VC12-4; See page 9.112.1Cavity Tool: CT12-4XX; See page 8.600.1Seal Kit: SK12-4X-MMM; See page 8.650.1E-Coil Nut: Part No. 7085180

SV12-40R

DIMENSIONS

1.410.2

111.3

MILLIMETRE

4.00101.6

2.0050.8

1.9850.3

1.25

ACROSS FLATS


31.8

3.95100.3

3.6993.7

4.44112.6

4.96125.9

INCH

1.1027.9

1.7644.8

TORQUE:10 ft-lbs.

(13.5 Nm) max.


2.1253.8

5.00127.0

4.39

0.194.8

3.6291.9

0.348.6

3.0978.5

1.1529.2

2

4

1

3

2

1

3

4

2.19

MANUALOVERRIDE

"P"

MANUALOVERRIDE

"T"

HY

DR

AF

OR

CE

55.5

HYDRAFORCE®

MATERIALS




TO ORDER

SV12-40R __ - __ __ __ - __ - __ __ __ __ __



3/4 in. BSP* 6B*BSP Body; U.K. Mfrs. Only


Voltage0 Less Coil

12 12 VDC24 24 VDC36 36 VDC48 48 VDC



IP69K Rated


Other coil voltagesmay be available forOEM applications.Consult factory.

ManualOverride

None (Blank)

Option POption T

SOLENOID VALVES



OPERATIONWhen de-energized, the SV08-41 blocks flow to all ports.

When energized, the spool shifts to open flow between ➂ and ➃, as well as from➁ to ➀.



FEATURES• Continuous-duty rated solenoid.• Hardened precision spool and cage for long life.• Optional coil voltages and terminations.• Efficient wet-armature construction.• All ports may be fully pressurized.• Cartridges are voltage interchangeable.• Manual override option.• Optional waterproof E-Coils rated up to IP69K.• Unitized, molded coil design.• Compact size.





USASI/ISO:

SYMBOLS


1.420.1

8.6/125

6.9/100

5.2/75

3.4/50

1.7/25

3.81

7.52

11.43

FLOW lpm/gpm

PR

ES

SU

RE

DR

OP

bar

/psi

15.14


➂ ➃ ➁ ➀

SV08-41

DIMENSIONS

1.420.2

1.8847.7

E-CoilView

Standard Coil View

1.4035.6

1.41 DIA.35.8

0.4310.9

HYDRAFORCE®

OptionNone (Blank)

Manual Override M

MATERIALS





SV08-41__ - __ __ __ - __ - __ __ __ __ __

TO ORDER















VoltageStd. Coil



terminations only


SOLENOID VALVES




When energized, the spool shifts to open flow between ➂ and ➃, as well as from➁ to ➀.




RATINGSOperating Pressure: 207 bar (3000 psi)Proof Pressure: 350 bar (5075 psi)Flow: See Performance ChartInternal Leakage: 82 cc/minute (5 cu. in./minute) max. at 207 bar (3000 psi)Temperature: -40 to 120°C with standard Buna sealsCoil Duty Rating: Continuous from 85% to 115% of nominal voltageResponse Time: First indication of change of state with 100% voltage supplied at





USASI/ISO:

SYMBOLS


1.422.1

8.6/125

6.9/100

5.2/75

3.4/50

1.7/25

7.52

15.14

22.76

FLOW lpm/gpm

PR

ES

SU

RE

DR

OP

bar

/psi

30.28


➂ ➃ ➁ ➀

SV10-41

DIMENSIONS

1.422.2

1.6241.1

1.84DIA.

46.7

0.4511.4

E-CoilView

StandardCoil View

2.3860.3

HYDRAFORCE®

MATERIALS TO ORDER





SV10-41__ - __ __ __ - __ - __ __ __ __ __


SAE 6 6TSAE 8 8T



OptionNone (Blank)













VoltageStd. Coil


12 12 VDC 24 24 VDC 36 36 VDC 48 48 VDC 24 24 VAC115 115 VAC230 230 VAC

**Includes Std. Coil Nut† DS, DW or DL

terminations only


SOLENOID VALVES

SV12-41 Spool, 2-Position, 4-Way

USASI/ISO:


SYMBOLS

1.424.1

2

1

3

4

10.3/150

6.9/100

8.6/125

3.4/50

5.2/75

1.7/25

37.910

18.95

56.815

FLOW lpm/gpm

PR

ES

SU

RE

DR

OP

bar

/psi

➁ to ➀ —; ➂ to ➃ - - -32 cSt/150 ssu oil at 40°C

276/4000

207/3000

138/2000

69/1000

37.910

18.95

56.815

75.820

FLOW lpm/gpm

PR

ES

SU

RE

bar

/psi



Inlet at ➂

110

120

60 7050403020100-20 -10-30-40

100

80

90

70

60

50% O

F R

AT

ED

VO

LTA

GE




Operating Range

DESCRIPTIONA solenoid-operated, 2-position, 4-way, direct-acting spool-type, screw-in hydrauliccartridge valve, intended as a bidirectional blocking valve.

OPERATIONWhen de-energized, the SV12-41 blocks flow at all ports. When energized, the spoolshifts to allow flow from ➂ to ➃, and from ➁ to ➀.





SV12-41

DIMENSIONS

1.424.2

111.3

MILLIMETRE

4.00101.6

2.0050.8

1.9850.3

1.25

ACROSS FLATS


31.8

3.95100.3

3.6993.7

INCH

1.1027.9

1.7644.8

TORQUE:10 ft-lbs.

(13.5 Nm) max.


2.1253.8

5.00127.0

4.39

0.194.8

3.6291.9

0.348.6

3.0978.5

1.1529.2

2

4

1

3

2

1

3

4

2.19

HY

DR

AF

OR

CE

55.5

HYDRAFORCE®

MATERIALS




TO ORDER

SV12-41 __ __ __ - __ - __ __ __ __ __





Voltage0 Less Coil

12 12 VDC24 24 VDC36 36 VDC48 48 VDC



IP69K Rated



SOLENOID VALVES



OPERATIONWhen de-energized, the SV08-42 directs flow from ➂ to ➃, and from ➁ to ➀.

When energized, the spool shifts to block flow at all ports.

Operation of Manual Override Option: To override, push button in and twistcounterclockwise 180°. The internal spring will push the button out. In this position thevalve may be only partially shifted. To assure full override shift, pull the button out toits fullest extension and hold it in this position.







USASI/ISO:

SYMBOLS


1.430.1

5.2/75

3.4/50

1.7/25

3.81

7.52

11.43

FLOW lpm/gpm

PR

ES

SU

RE

DR

OP

bar

/psi


➂ ➃ ➁ ➀

SV08-42

DIMENSIONS

1.430.2

1.8847.7

E-CoilView

Standard Coil View

1.4035.6

1.41 DIA.35.8

0.4310.9

HYDRAFORCE®

OptionNone (Blank)

Manual Override M

MATERIALS





SV08-42__ - __ __ __ - __ - __ __ __ __ __

TO ORDER















VoltageStd. Coil



terminations only



OPERATIONWhen de-energized, the SV10-42 allows flow from ➂ to ➃, as well as from ➁ to ➀.

When energized, the spool shifts to block flow at all ports.




RATINGSOperating Pressure: 207 bar (3000 psi)Proof Pressure: 350 bar (5075 psi)Flow: See Performance ChartInternal Leakage: 82 cc/minute (5 cu. in./minute) max. at 207 bar (3000 psi)Temperature: -40 to 120°C with standard Buna sealsCoil Duty Rating: Continuous from 85% to 115% of nominal voltageInitial Coil Current Draw at 20°C: Standard Coil: 1.67 amps at 12 VDC; 0.18 amps




SOLENOID VALVES


SYMBOLS

USASI/ISO:


1.432.1

6.9/100

5.5/80

4.1/60

2.8/40

1.4/20

7.52

15.14

22.76

FLOW lpm/gpm

PR

ES

SU

RE

DR

OP

bar

/psi


➂ ➃ ➁ ➀

SV10-42

DIMENSIONS

1.432.2

1.6241.1

1.84DIA.

46.7

0.4511.4

E-CoilView

StandardCoil View

2.3860.3

HYDRAFORCE®

MATERIALS TO ORDER





SV10-42__ - __ __ __ - __ - __ __ __ __ __


SAE 6 6TSAE 8 8T



OptionNone (Blank)













VoltageStd. Coil




terminations only


SOLENOID VALVES


USASI/ISO:


SYMBOLS

1.434.1

2

1

3

4

10.3/150

6.9/100

8.6/125

3.4/50

5.2/75

1.7/25

37.910

18.95

56.815

FLOW lpm/gpm

PR

ES

SU

RE

DR

OP

bar

/psi

➁ to ➀ —; ➂ to ➃ - - -32 cSt/150 ssu oil at 40°C

276/4000

207/3000

138/2000

69/1000

37.910

18.95

56.815

75.820

FLOW lpm/gpm

PR

ES

SU

RE

bar

/psi



Inlet at ➂

110

120

60 7050403020100-20 -10-30-40

100

80

90

70

60

50% O

F R

AT

ED

VO

LTA

GE




Operating Range

DESCRIPTIONA solenoid-operated, 2-position, 4-way, direct-acting spool-type, screw-in hydrauliccartridge valve.

OPERATIONWhen de-energized, the SV12-42 allows flow from ➂ to ➃, and from ➁ to ➀. Whenenergized, the spool shifts to block flow at all ports.


FEATURES• Continuous-duty rated solenoid.• Hardened spool and cage for long life.• Optional coil voltages and terminations.• All ports may be fully pressurized.• Manual override option.• Heavy-duty waterproof E-Coils rated up to IP69K.



SV12-42

DIMENSIONS

1.434.2

111.3

MILLIMETRE

4.00101.6

2.0050.8

1.9850.3

1.25

ACROSS FLATS


31.8

3.95100.3

3.6993.7

4.44112.6

4.96125.9

INCH

1.1027.9

1.7644.8

TORQUE:10 ft-lbs.

(13.5 Nm) max.


2.1253.8

5.00127.0

4.39

0.194.8

3.6291.9

0.348.6

3.0978.5

1.1529.2

2

4

1

3

2

1

3

4

2.19

MANUALOVERRIDE

"P"

MANUALOVERRIDE

"T"

HY

DR

AF

OR

CE

55.5

HYDRAFORCE®

MATERIALS




TO ORDER

SV12-42 __ - __ __ __ - __ - __ __ __ __ __





Voltage0 Less Coil

12 12 VDC24 24 VDC36 36 VDC48 48 VDC



IP69K Rated


Other coil voltagesmay be available forOEM applications.Consult factory.

ManualOverride

None (Blank)

Option POption T

SOLENOID VALVES



OPERATIONWhen de-energized, the SV08-43 allows flow from ➃ to ➀, while blocking ➂ and ➁.

When energized, the spool shifts to allow flow from ➂ to ➃ and ➁ to ➀.

Note: While port ➀ may be fully pressurized, it is not intended for use as the valve’sinlet.

FEATURES• Continuous-duty rated solenoid.• Hardened precision spool and cage for long life.• Optional coil voltages and terminations.• Efficient wet-armature construction.• All ports may be fully pressurized.• Cartridges are voltage interchangeable.• Optional waterproof E-Coils rated up to IP69K.• Unitized, molded coil design.• Industry-common cavity.





USASI/ISO:

SYMBOLS


1.440.1

8.6/125

6.9/100

5.2/75

3.4/50

1.7/25

3.81

7.52

11.43

FLOW lpm/gpm

PR

ES

SU

RE

DR

OP

bar

/psi

➃ to ➀ ———➂ to ➃ – – – –➁ to ➀ - - - - - -


SV08-43

DIMENSIONS

1.440.2

Standard Coil View

1.8847.7

1.8847.7

E-CoilView

1.4035.6

1.41 DIA.35.8

HYDRAFORCE®

OptionNone (Blank)

MATERIALS





SV08-43__ - __ __ __ - __ - __ __ __ __ __

TO ORDER















VoltageStd. Coil




terminations only


SOLENOID VALVES



OPERATIONWhen de-energized, the SV10-43 allows flow from ➃ to ➀, while blocking ➂ and ➁.

When energized, the spool shifts to allow flow from ➂ to ➃ and from ➁ to ➀.

Note that while ➀ may be fully pressurized, it is not intended for use as the valve'sinlet.




RATINGSOperating Pressure: 207 bar (3000 psi)Proof Pressure: 350 bar (5075 psi)Flow: See Performance ChartInternal Leakage: 82 cc/minute (5 cu. in./minute) max. at 207 bar (3000 psiTemperature: -40 to 120°C with standard Buna sealsCoil Duty Rating: Continuous from 85% to 115% of nominal voltageInitial Coil Current Draw at 20°C: Standard Coil: 1.67 amps at 12 VDC; 0.18 amps




SYMBOLS

USASI/ISO:


1.442.1

6.9/100

5.5/80

4.1/60

2.8/40

1.4/20

7.52

15.14

22.56

FLOW lpm/gpm

PR

ES

SU

RE

DR

OP

bar

/psi

to — ; to . . . ; to - - -


➂ ➃ ➁ ➀➃ ➀

SV10-43

DIMENSIONS

1.442.2

1.6241.1

1.84DIA.

46.7

0.4511.4

E-CoilView

StandardCoil View

2.3860.3

HYDRAFORCE®

MATERIALS TO ORDER





SV10-43__ - __ __ __ - __ - __ __ __ __ __


SAE 6 6TSAE 8 8T



OptionNone (Blank)













VoltageStd. Coil




terminations only



OPERATIONWhen de-energized, the SV08-44 allows flow from ➂ to ➃, and from ➁ to ➀.

When energized, the spool shifts to allow flow from ➂ to ➀, while blocking ➁ and ➃.



Note: While ➀ may be fully pressurized, it is not intended for use as thevalve’s inlet.






SOLENOID VALVES


SYMBOLS

USASI/ISO:


1.450.1

4.1/60

5.5/80

6.9/100

8.3/120

2.8/40

1.4/20

3.81

7.52

11.43

FLOW lpm/gpm

PR

ES

SU

RE

DR

OP

bar

/psi


➂ to ➀ En

➁ to ➀ De-En

➂ to ➃ De-En

SV08-44

DIMENSIONS

1.450.2

1.8847.7

E-CoilView

Standard Coil View

1.4035.6

1.41 DIA.35.8

0.4310.9

HYDRAFORCE®

OptionNone (Blank)

Manual Override M

MATERIALS





SV08-44__ - __ __ __ - __ - __ __ __ __ __

TO ORDER















VoltageStd. Coil



terminations only


SOLENOID VALVES



OPERATIONWhen de-energized, the SV10-44 allows flow from ➂ to ➃, as well as from ➁ to ➀.

When energized, the cartridge’s spool shifts to open ➂ to ➀ while blocking ➃ and ➁.








SYMBOLSUSASI/ISO:

1.452.1


8.6/100

6.9/80

5.2/60

3.4/40

1.7/20

7.52

7.53

7.51

15.14

15.15

22.76

FLOW lpm/gpm

PR

ES

SU

RE

DR

OP

bar

/psi


➂ to ➃ De-En

➁ to ➀ De-En

➂ to ➀ En

DIMENSIONS

SV10-44

1.452.2

1.6241.1

1.84DIA.

46.7

0.4511.4

E-CoilView

StandardCoil View

2.3860.3

HYDRAFORCE®

MATERIALS TO ORDER





SV10-44__ - __ __ __ - __ - __ __ __ __ __


SAE 6 6TSAE 8 8T



OptionNone (Blank)













VoltageStd. Coil


12 12 VDC 24 24 VDC 36 36 VDC 48 48 VDC 24 24 VAC115 115 VAC230 230 VAC**Includes Std. Coil Nut† DS, DW or DLterminations only


SOLENOID VALVES




When energized, the spool shifts to open flow between ➂ and ➁, as well as from➃ to ➀.








USASI/ISO:

SYMBOLS


1.460.1

5.5/80

4.1/60

2.8/40

1.4/20

3.81

7.62

11.43

FLOW lpm/gpm

PR

ES

SU

RE

DR

OP

bar

/psi


➂ ➁ ➃ ➀

SV08-45

DIMENSIONS

1.460.2

1.8847.7

E-CoilView

Standard Coil View

1.4035.6

1.41 DIA.35.8

0.4310.9

HYDRAFORCE®

OptionNone (Blank)

Manual Override M

MATERIALS





SV08-45__ - __ __ __ - __ - __ __ __ __ __

TO ORDER















VoltageStd. Coil




terminations only



OPERATIONWhen de-energized, the SV08-46 allows flow from ➀ to ➃, and from ➂ to ➁.

When energized, the spool shifts to allow flow between ➁, ➀ and ➃, while blockingflow at ➂.








SOLENOID VALVES


SYMBOLS

USASI/ISO:


1.470.1

5.5/80

4.1/60

2.8/40

1.4/20

3.81

7.62

11.43

FLOW lpm/gpm

PR

ES

SU

RE

DR

OP

bar

/psi

to — ; to - - - (d)32 cSt/150 ssu oil at 40°C➂ ➁ ➃ ➀

SV08-46

DIMENSIONS

1.470.2

1.8847.7

E-CoilView

Standard Coil View

1.4035.6

1.41 DIA.35.8

0.4310.9

HYDRAFORCE®

OptionNone (Blank)

Manual Override M

MATERIALS





SV08-46__ - __ __ __ - __ - __ __ __ __ __

TO ORDER















VoltageStd. Coil




terminations only


SOLENOID VALVES

SV08-47A Spool, 4-Way, 3-Position, Tandem Center

SYMBOLSUSASI:

1.500.1

ISO:


13.8/200

10.3/150

6.9/100

3.4/50

1.90.5

5.71.5

3.81.0

7.52.0

9.52.5

11.43.0

FLOW lpm/gpm

PR

ES

SU

RE

DR

OP

bar

/psi

13.23.5

➂ to ➁ or ➂ to ➃ ——➁ to ➀ or ➃ to ➀ – – –

➂ to ➀ - - - -32 cSt/150 ssu oil at 40°C

276/4000

207/3000

138/2000

69/1000

3.81

7.52

11.43

OPERATING FLOW lpm/gpmOP

ER

AT

ING

PR

ES

SU

RE

bar

/psi

15.14


DESCRIPTIONA solenoid-operated, 4-way, 3-position, direct-acting, spool-type, tandem center,screw-in hydraulic cartridge valve.

OPERATIONWhen de-energized, the SV08-47A blocks cylinder ports, while allowing flow from ➂to ➀. When coil #1 is energized, flow is allowed from ➂ to ➁, and from ➃ to ➀. Whencoil #2 is energized, flow is allowed from ➂ to ➃, and from ➁ to ➀.

In circuits where work port flows are unequal due to cylinder ratios, the higher returnflow should be directed to port ➁.

While ➀ may be fully pressurized, it is not intended for use as the valve’s inlet.

Operation of Manual Override Option: To override, push the knurled knob to activatethe coil #2 (S2) function; pull the knob to activate the coil #1 (S1) function.

FEATURES• Continuous-duty rated solenoid.• Hardened precision spool and cage for long life.• Optional coil voltages and terminations.• Efficient wet-armature construction.• All ports may be fully pressurized.• Cartridges are voltage interchangeable.• Unitized, molded coil design.• Manual override option.• Optional waterproof E-Coils rated up to IP69K.

RATINGSOperating Pressure: 210 bar (3000 psi)Flow: 11.4 lpm (3.0 gpm) max.Internal Leakage: 278 cc/minute (17 cu. in./minute) max. at 207 bar (3000 psi)Temperature: -40 to 120°C with standard Buna sealsCoil Duty Rating: Continuous from 85% to 115% of nominal voltageInitial Coil Current Draw at 20°C: Standard Coil: 1.2 amps at 12 VDC; 0.13 amps at


7.4 to 420 cSt (50 to 2000 ssu). For high viscosity applications, consult factory.Installation: No restrictions; See page 9.020.1Cavity: VC08-4; See page 9.108.1Cavity Tool: CT08-4XX; See page 8.600.1Seal Kit: SK08-4X-MMM; See page 8.650.1Coil Nut: Part No. 7004400; Manual Override Coil Nut: Part No. 4528180;Coil Spacer: Part No. 4534720For E-coils manufactured prior to 1-1-04, see page 3.400.1 for coil nut & spacer info.

420

200

75

3.81

7.52

11.43


VIS

CO

SIT

Y c

St

Fluid Viscosity vs. Flow

SV08-47A

1.500.2

DIMENSIONS

1.4035.6

3.3885.9

0.8822.2

1.41 DIA.35.8

E-CoilViewStandard

Coil View

3.7896.0

20 ft-lbs(27.2 Nm)max.

HYDRAFORCE®

OptionNone (Blank)

Manual Override M

MATERIALS



Standard Coil: Weight each:0.11 kg. (0.25 lbs.); Unitizedthermoplastic encapsulated,Class H high temperaturemagnetwire; See page 3.200.1.

E-Coil: Weight each: 0.14 kg.(0.3 lbs.); Fully encapsulatedwith rugged external metal shell;Rated up to IP69K with integralconnectors; See page 3.400.1for E-Coil retrofit applications.

VoltageStd. Coil


12 12 VDC 24 24 VDC 36 36 VDC 48 48 VDC 24 24 VAC115 115 VAC230 230 VAC**Includes coil nut and coil spacer† DS, DW or DL

terminations only

SV08-47A__ - __ __ __ - __ - __ __ __ __ __

TO ORDER
















SOLENOID VALVES

SV10-47A Spool, 4-Way, 3-Position, Tandem Center

SYMBOLS

USASI:

ISO:

1.502.1


OPERATIONWhen de-energized, the SV10-47A blocks cylinder ports, while allowing flow from ➂to ➀. When coil #1 is energized, flow is allowed from ➂ to ➁, and from ➃ to ➀. Whencoil #2 is energized, flow is allowed from ➂ to ➃, and from ➁ to ➀.



Operaton of Manual Override Option: To override, push the knurled button toactivate the coil #2 (S2) function, or pull the knob to activate the coil #1 (S1) function.

FEATURES• Optional coil voltages and terminations.• Efficient wet-armature construction.• All ports may be fully pressurized.• Cartridges are voltage interchangeable.• Hardened precision spool and cage for long life.

RATINGSOperating Pressure: 240 bar (3500 psi)Proof Pressure: 390 bar (5700 psi)Flow: 19 lpm (5 gpm) max.Internal Leakage: 300 cc/minute (20 cu. in./minute) max. at 207 bar (3000 psi)Temperature: -40 to 120°C with standard Buna sealsCoil Duty Rating: Continuous from 85% to 115% of nominal voltageResponse Time: First indication of change of state with 85% voltage supplied at



7.4 to 420 cSt (50 to 2000 ssu)Installation: No restrictions; See page 9.020.1Cavity: VC10-4; See page 9.110.1Cavity Tool: CT10-4XX; See page 8.600.1Seal Kit: SK10-4X-MMM; See page 8.650.1Coil Nut: Part No. 7004400; Manual Override Coil Nut: Part No. 4528180Coil Spacer: Part No. 4539700For E-coils manufactured prior to 1-1-04, see page 3.400.1 for coil nut & spacer info.


8.6/125

6.9/100

5.2/75

3.4/50

1.7/25

3.81

7.52

11.43

FLOW lpm/gpm

PR

ES

SU

RE

DR

OP

bar

/psi

15.14

18.95

to , to Loop — ; to Neutral - - -


➂ ➁ ➃ ➀➂ ➀

• Continuous-duty rated solenoid.• Manual override option.• Optional waterproof E-Coils

rated up to IP69K.• Unitized, molded coil design.

276/4000

207/3000

138/2000

69/1000

3.81

7.52

11.43

OPERATING FLOW lpm/gpmOP

ER

AT

ING

PR

ES

SU

RE

bar

/psi

15.14

18.95


SV10-47A

1.502.2

DIMENSIONS

1.6241.1

1.84DIA.

46.7

4.45113.0

4.97126.2

E-CoilViewStandard

Coil View

HYDRAFORCE®

MATERIALS TO ORDER



Standard Coils: Weight each:0.27 kg. (0.60 lbs.); Unitizedthermoplastic encapsulated,Class H high temperaturemagnetwire; See page 3.200.1.

E-Coils: Weight each: 0.41 kg.(0.9 lbs.); Fully encapsulatedwith rugged external metal shell;Rated up to IP69K with integralconnectors; See page 3.400.1for E-Coil retrofit applications.

SV10-47A__ - __ __ __ - __ - __ __ __ __ __


SAE 6 6TSAE 8 8T



OptionNone (Blank)

Manual Override MFor Manual Override optionssee page 1.001.1












VoltageStd. Coil



terminations only


DESCRIPTIONA solenoid-operated, 4-way, 3-position, direct-acting, spool-type, open center,screw-in hydraulic cartridge valve.

OPERATIONWhen de-energized, the SV08-47B allows flow to all ports. When coil #1 is energized,flow is allowed from ➂ to ➃, and from ➁ to ➀. When coil #2 is energized, flow isallowed from ➂ to ➁, and from ➃ to ➀.



Operation of Manual Override Option: To override, push the knurled button toactivate the coil #2 (S2) function, or pull the knob to activate the coil #1 (S1) function.

FEATURES• Continuous-duty rated solenoid.• Hardened precision spool and cage for long life.• Optional coil voltages and terminations.• Efficient wet-armature construction.• All ports may be fully pressurized.• Cartridges are voltage interchangeable.• Unitized, molded coil design.• Compact size.• Optional waterproof E-Coils rated up to IP69K.• Manual override option.

RATINGSOperating Pressure: 207 bar (3000 psi)Flow: 11.4 lpm (3 gpm) max.Internal Leakage: 328 ml/minute (20 cu. in./minute) max. at 207 bar (3000 psi)Temperature: -40 to 120°C with standard Buna sealsCoil Duty Rating: Continuous from 85% to 115% of nominal voltageInitial Coil Current Draw at 20° C: Standard Coil: 1.2 amps at 12 VDC; 0.13 amps at


7.4 to 420 cSt (50 to 2000 ssu)Installation: No restrictions; See page 9.020.1Cavity: VC08-4; See page 9.108.1Cavity Tool: CT08-4XX; See page 8.600.1Seal Kit: SK08-4X-MMM; See page 8.650.1Coil Nut: Part No. 7004400; Manual Override Coil Nut: Part No. 4528180;Coil Spacer: Part No. 4534720For E-coils manufactured prior to 1-1-04, see page 3.400.1 for coil nut & spacer info.

SOLENOID VALVES

SV08-47B Spool, 4-Way, 3-Position, Open Center

SYMBOLSUSASI:

ISO:

1.508.1


5.2/75

3.4/50

1.7/25

1.90.5

5.71.5

3.81.0

7.52.0

9.52.5

11.43.0

FLOW lpm/gpm

PR

ES

SU

RE

DR

OP

bar

/psi

➂ to ➁, or ➂ to ➃, or ➃ to ➀ ——➁ to ➀ – – –

➂ to ➀ Neutral - - - -32 cSt/150 ssu oil at 40°C

SV08-47B

1.508.2

DIMENSIONS

1.4035.6

3.3885.9

0.8822.2

1.41 DIA.35.8

E-CoilViewStandard

Coil View

3.7896.0


HYDRAFORCE®

OptionNone (Blank)

Manual Override M

MATERIALS

SV08-47B__ - __ __ __ - __ - __ __ __ __ __

TO ORDER



















VoltageStd. Coil



terminations only


DESCRIPTIONA solenoid-operated, 4-way, 3-position, direct-acting, spool-type, open center, screw-in hydraulic cartridge valve.

OPERATIONWhen de-energized, SV10-47B cylinder ports are open and common to ➂ and ➀.When coil #1 is energized, flow is allowed from ➂ to ➃, and from ➁ to ➀. When coil#2 is energized, flow is allowed from ➂ to ➁, and from ➃ to ➀.




FEATURES• Continuous-duty rated solenoid.• Hardened precision spool and cage for long life.• Optional coil voltages and terminations.• Manual override option.• Optional waterproof E-Coils rated up to IP69K.• Efficient wet-armature construction.• All ports may be fully pressurized.• Cartridges are voltage interchangeable.• Unitized, molded coil design.• Industry common cavity.

RATINGSOperating Pressure: 240 bar (3500 psi)Proof Pressure: 390 bar (5700 psi)Flow: 22.7 lpm (6 gpm) max.Internal Leakage: 328 cc/minute (20 cu. in./minute) max. at 207 bar (3000 psi)Temperature: -40 to 120°C with standard Buna sealsCoil Duty Rating: Continuous from 85% to 115% of nominal voltageResponse Time: First indication of change of state with 100% voltage supplied at




SOLENOID VALVES

SV10-47B Spool, 4-Way, 3-Position, Open Center

USASI:

SYMBOLS

ISO:


1.510.1

3.4/50

5.2/75

6.9/100

1.7/25

3.81

7.52

11.43

15.14

18.95

22.76

FLOW lpm/gpm

PR

ES

SU

RE

DR

OP

bar

/psi

➂ to ➁ or ➃, or ➃ to ➀ - - - -➂ to ➀, or ➁ to ➀ ——


DIMENSIONS

SV10-47B

1.510.2

1.6241.1

1.84DIA.

46.7

4.45113.0

4.97126.2

E-CoilViewStandard

Coil View

HYDRAFORCE®

MATERIALS TO ORDER

SV10-47B__ - __ __ __ - __ - __ __ __ __ __


SAE 6 6TSAE 8 8T





OptionNone (Blank)

Manual Override MManual Override T















VoltageStd. Coil



terminations only


DESCRIPTIONA solenoid-operated, 4-way, 3-position, direct-acting, spool-type, closed center,screw-in hydraulic cartridge valve.

OPERATIONWhen de-energized, the SV08-47C blocks flow to all ports. When coil #1 is energized,flow is allowed from ➂ to ➃, and from ➁ to ➀. When coil #2 is energized, flow isallowed from ➂ to ➁, and from ➃ to ➀.





RATINGSOperating Pressure: 207 bar (3000 psi)Flow: 11.4 lpm (3 gpm) max.Internal Leakage: 164 cc/minute (10 cu. in./minute) max. at 207 bar (3000 psi)Temperature: -40 to 120°C with standard Buna sealsCoil Duty Rating: Continuous from 85% to 115% of nominal voltageInitial Coil Current Draw at 20° C: Standard Coil: 1.2 amps at 12 VDC; 0.13 amps at



SOLENOID VALVES

SV08-47C Spool, 4-Way, 3-Position, Closed Center

SYMBOLSUSASI:

ISO:

1.520.1


6.9/100

5.2/75

3.4/50

1.7/25

3.81

7.52

11.43

FLOW lpm/gpm

PR

ES

SU

RE

DR

OP

ba

r/p

si

to or — ; or to - - -


➂ ➁ ➃➁ ➃ ➀

SV08-47C

1.520.2

DIMENSIONS

1.4035.6

3.3885.9

0.8822.2

1.41 DIA.35.8

E-CoilViewStandard

Coil View

3.7896.0


HYDRAFORCE®

OptionNone (Blank)

Manual Override M

MATERIALS

SV08-47C__ - __ __ __ - __ - __ __ __ __ __

TO ORDER



















VoltageStd. Coil



terminations only


DESCRIPTIONA solenoid-operated, 4-way, 3-position, direct-acting, spool-type, closed center,screw-in hydraulic cartridge valve.

OPERATIONWhen de-energized, the SV10-47C blocks flow to all ports. When coil #1 is energized,flow is allowed from ➂ to ➃, and from ➁ to ➀. When coil #2 is energized, flow isallowed from ➂ to ➁, and from ➃ to ➀.





RATINGSOperating Pressure: 207 bar (3000 psi)Proof Pressure: 390 bar (5700 psi)Flow: 23 lpm (6 gpm) max.Internal Leakage: 164 cc/minute (10 cu. in./minute) max. at 207 bar (3000 psi)Temperature: -40 to 120°C with standard Buna sealsCoil Duty Rating: Continuous from 85% to 115% of nominal voltageInitial Coil Current Draw at 20° C: Standard Coil: 1.67 amps at 12 VDC; 0.18 amps



SOLENOID VALVES

SV10-47C Spool, 4-Way, 3-Position, Closed Center

SYMBOLS

1.522.1

USASI:

ISO:


6.9/100

5.2/75

3.4/50

1.7/25

7.52

15.14

22.76

FLOW lpm/gpm

PR

ES

SU

RE

DR

OP

bar

/psi

to or — ; or to - - -


➂ ➁ ➃➁ ➃ ➀

DIMENSIONS

SV10-47C

1.522.2

1.6241.1

1.84DIA.

46.7

4.45113.0

4.97126.2

E-CoilViewStandard

Coil View

HYDRAFORCE®

MATERIALS TO ORDER

SV10-47C__ - __ __ __ - __ - __ __ __ __ __


SAE 6 6TSAE 8 8T





OptionNone (Blank)
















VoltageStd. Coil



terminations only


DESCRIPTIONA solenoid-operated, 4-way, 3-position, direct-acting, spool-type, motor spool, screw-in hydraulic cartridge valve.

OPERATIONWhen de-energized, the SV08-47D blocks flow to ➂, while allowing flow from ➁ to ➀,and from ➃ to ➀. When coil #1 is energized, flow is allowed from ➂ to ➃, and from ➁to ➀. When coil #2 is energized, flow is allowed from ➂ to ➁, and from ➃ to ➀.








SOLENOID VALVES

SV08-47D Spool, 4-Way, 3-Position, “Motor Spool”

SYMBOLS

1.530.1

USASI:

ISO:


5.2/75

3.1/45

2.1/30

1.0/15

3.81

7.52

11.43

FLOW lpm/gpm

PR

ES

SU

RE

DR

OP

bar

/psi

➂ to ➁, ➂ to ➃, ➃ to ➀ — ;➁ to ➀ - - -


1.90.5

5.71.5

9.52.5

4.1/60

SV08-47D

1.530.2

DIMENSIONS

1.4035.6

3.3885.9

0.8822.2

1.41 DIA.35.8

E-CoilViewStandard

Coil View

3.7896.0


HYDRAFORCE®

OptionNone (Blank)

Manual Override M

MATERIALS

SV08-47D__ - __ __ __ - __ - __ __ __ __ __TO ORDER



















VoltageStd. Coil



terminations only


DESCRIPTIONA solenoid-operated, 4-way, 3-position, direct-acting, spool-type, motor spool, screw-in hydraulic cartridge valve.

OPERATIONWhen de-energized, the SV10-47D blocks flow to ➂, while allowing flow from ➁ to ➀,and from ➃ to ➀. When coil #1 is energized, flow is allowed from ➂ to ➃, and from ➁to ➀. When coil #2 is energized, flow is allowed from ➂ to ➁, and from ➃ to ➀.








SOLENOID VALVES

SV10-47D Spool, 4-Way, 3-Position, “Motor Spool”

USASI:

ISO:


SYMBOLS

1.532.1

6.9/100

5.2/75

3.4/50

1.7/25

7.52

15.14

22.76

FLOW lpm/gpm

PR

ES

SU

RE

DR

OP

bar

/psi

to or — ; or to - - -


➂ ➁ ➃➁ ➃ ➀

DIMENSIONS

SV10-47D

1.532.2

1.6241.1

1.84DIA.

46.7

4.45113.0

4.97126.2

E-CoilViewStandard

Coil View

HYDRAFORCE®

MATERIALS TO ORDER

SV10-47D__ - __ __ __ - __ - __ __ __ __ __


SAE 6 6TSAE 8 8T





OptionNone (Blank)
















VoltageStd. Coil



terminations only



OPERATIONWhen de-energized, the SV08-47E blocks flow at ➂ and ➃, while allowing flow from➁ to ➀. When coil #1 (S1) is energized, the spool shifts to allow flow from ➂ to ➃ and➁ to ➀. When coil #2 (S2) is energized flow is allowed from ➁ to ➂ and from ➃ to ➀.



FEATURES• Continuous-duty rated solenoid.• Hardened precision spool and cage for long life.• Optional coil voltages and terminations.• Efficient wet-armature construction.• All ports may be fully pressurized.• Cartridges are voltage interchangeable.• Unitized, molded coil design.• Industry common cavity.• Optional waterproof E-Coils rated up to IP69K.



7.4 to 420 cSt (50 to 2000 ssu)Installation: No restrictions; See page 9.020.1Cavity: VC08-4; See page 9.108.1Cavity Tool: CT08-4XX; See page 8.600.1Seal Kit: SK08-4X-MMM; See page 8.650.1Coil Nut: Part No. 7004400; Coil Spacer: Part No. 4534720For E-coils manufactured prior to 1-1-04, see page 3.400.1 for coil nut & spacer info.

SOLENOID VALVES

SV08-47E Spool, 4-Way, 3-Position

SYMBOLSUSASI:

ISO:

1.540.1


5.2/75

3.4/50

1.7/25

3.81

7.52

11.43

FLOW lpm/gpm

PR

ES

SU

RE

DR

OP

bar

/psi

➃ to ➀ ———➂ to ➁ or ➂ to ➃ – – – –

➁ to ➀ - - - - -32 cSt/150 ssu oil at 40°C

SV08-47E

1.540.2

DIMENSIONS

1.4035.6

3.3585.1

0.8822.1

1.41 DIA.35.8

E-CoilView

35.8

StandardCoil View

3.3585.1


HYDRAFORCE®

OptionNone (Blank)

MATERIALS

SV08-47E__ - __ __ __ - __ - __ __ __ __ __TO ORDER



















VoltageStd. Coil



terminations only


DESCRIPTIONA solenoid-operated, 4-way, 3-position, direct-acting, spool-type, motor center, screw-in hydraulic cartridge valve.

OPERATIONWhen de-energized, the SV10-47E blocks flow at 3 and 4, while allowing flow from 2 to 1. When coil #1 (S1) is energized, the spool shifts to allow flow from 3 to 4 and 2 to 1. When coil #2 (S2) is energized flow is allowed from 2 to 3 and from 4 to 1.In circuits where work port flows are unequal due to cylinder ratios, the higher return flow should be directed to port 2.While 1 may be fully pressurized, it is not intended for use as the valve’s inlet.

FEATURES• Continuous-duty rated solenoid with optional coil voltages and terminations.• Hardened precision spool and cage for long life.• Manual override option.• Optional waterproof E-Coils rated up to IP69K.• Efficient wet-armature construction.• All ports may be fully pressurized.• Cartridges are voltage interchangeable.• Unitized, molded coil design.• Industry common cavity.

RATINGSOperating Pressure: 250 bar (3625 psi)Proof Pressure: 344 bar (5000 psi)Flow: Up to 30.2 (8 gpm); see performance chartInternal Leakage: 328 cc/minute (20 cu. in./minute) max. at 207 bar (3000 psi)Temperature: -40 to 100°C (-40° to 212°F) with standard Buna N seals;

-26 to 204°C (-15°F to 400°F) with Fluorocarbon seals;-54 to 107°C (-65°F to 225°F) with Polyurethane seals


80% of nominal flow rating: Energized: 40 msec.; De-energized: 10 msec.Initial Coil Current Draw at 20°C: Standard Coil: 1.67 amps at 12 VDC;

0.18 amps at 115 VAC (full wave rectified). E-Coil: 1.7 amps at 12 VDC; 0.85 amps at 24 VDC


7.4 to 420 cSt (50 to 2000 sus); See Temperature and Oil Viscosity, page 9.060.1Installation: No restrictions; See page 9.020.1Cavity: VC10-4; See page 9.110.1; Cavity Tool: CT10-4XX; See page 8.600.1Seal Kit: SK10-4X-MMM; See page 8.650.1Coil Nut: Part No. 7004400; Manual Override Coil Nut: Part No. 4528180Coil Spacer: E-Coil Spacer Part No. 4539700; Std. D-Coil Spacer Part No. 7000280;

If cartridge is ordered "Less Coil," D-Coil spacer will be provided.

SV10-47E Spool, 4-Way, 3-Position

SYMBOL


1.542.1

4

3

2

1

SOLENOID VALVES

HYDRAFORCE.com®

8.6/125

6.9/100

5.2/75

3.4/50

1.7/25

6.9/100

5.2/75

3.4/50

1.7/25

3.81

11.43

15.94

18.95

7.52

FLOW lpm/gpm

PR

ES

SU

RE

bar

/psi

22.76

3 to 4 (S1 Energized) ———3 to 1 (S2 Energized) — - — -4 to 1 (S2 Energized) – – – –2 to 1 (De-Energized) - - - - - -2 to 1 (S1 Energized) — — —


See following page for additional performance information.


RP


SV10-47E

1.542.2

DIMENSIONSPERFORMANCE (Continued)

®HYDRAFORCE

HYDRAFORCE.com®

SV10-47E__ - __ __ __ - __ - __ __ __ __ __

TO ORDER


MATERIALS


Standard Ported Body: Weight: 0.36 kg. (0.80 lbs.); Anodized high-strength 6061 T6 alumi-num alloy, rated to 207 bar (3000 psi); Ductile iron bodies available; dimensions may differ. See page 8.010.1.

Standard D-Coil: Weight each: 0.27 kg. (0.60 lbs.); Unitized thermoplastic encapsulated, Class H high temperature magnetwire. See page 3.200.1

E-Coil: Weight: 0.41 kg.(0.9 lbs.); Perfect wound, fully encapsulated with ruggedexternal metal shell; Rated up to IP69K with integralconnectors. See page 3.400.1

Porting Cartridge Only 0 SAE 6 6T SAE 8 8T 1/4 in. BSP* 2B 3/8 in. BSP* 3B


Option None (Blank) Manual Override M Manual Override B Manual Override K

For Manual Override optioninfo., see page 1.001.1

2.4462.0

SHOWN ABOVE WITH E-COILS AND EY CONNECTORS OPTION

4

3

2

1

1

2.5464.5

Across FlatsTORQUE:

24–26 ft-lbs(32.5–35.3 Nm)

1.0025.4

INCHMILLIMETRE

COILS MUST BE INSTALLEDWITH LETTERING UP

1.2531.8

1.2531.8 2.50

63.5

S1

S2

3.2582.6

0.256.4

2.0050.8

2.8472.1

1.3634.5

0.7418.8

1.9950.5

2

3

4

0.287.1

E-Coil Dia.D-Coil Dia.

1.8446.7

1.7344.0

ManualOverride

Across FlatsTORQUE:5–7 ft-lbs

(6.8–9.5 Nm)

0.7519.16.33

160.8

5.77146.6

Options“M” or “B”

Option“K”

1.50 38.1

“B” or “K”Knob: Dia.

Voltage Std. D-Coil 0 Less Coil** 10 10 VDC†

12 12 VDC 20 20 VDC 24 24 VDC 36 36 VDC 48 48 VDC 24 24 VAC 115 115 VAC 230 230 VAC**Includes D-Coil

Nut and Spacer.† DS, DW or DL

terminations only.

E-Coils: 10, 12, 20, 24 VDC only.



2764000

2073000

1382000

691000


OP

ER

AT

ING

PR

ES

SU

RE

bar

/psi

3.81

11.43

15.94

18.95

7.52

22.76

26.57

30.28

Performance Range Hatched


RP


SOLENOID VALVES

SV10-47F Spool, 4-Way, 3-Position, Tandem Center


OPERATIONWhen de-energized, the SV10-47F blocks cylinder ports, while allowing flow from ➂to ➀. When coil #1 is energized, flow is allowed from ➂ to ➁, and from ➃ to ➀. Whencoil #2 is energized, flow is allowed from ➁ to ➂, while blocking flow to ➀ and ➃.



Operaton of Manual Override Option: To override, push the knurled button toactivate the coil #2 (S2) function, or pull the knob to activate the coil #1 (S1) function.


RATINGSOperating Pressure: 240 bar (3500 psi)Proof Pressure: 390 bar (5700 psi)Flow: 15 lpm (4 gpm) max.Internal Leakage: 164 cc/minute (10 cu. in./minute) max. at 207 bar (3000 psi)Temperature: -40 to 120°C with standard Buna sealsCoil Duty Rating: Continuous from 85% to 115% of nominal voltageResponse Time: First indication of change of state with 100% voltage supplied at




SYMBOLS

USASI:


1.552.1

8.6/125

6.9/100

5.2/75

3.4/50

1.7/25

3.81

7.52

11.43

FLOW lpm/gpm

PR

ES

SU

RE

DR

OP

bar

/psi

15.14

to - to Loop — ; to Neutral - - -


➂ ➁ ➃ ➀➂ ➀

ISO:

SV10-47F

1.552.2

DIMENSIONS

1.6241.1

1.84DIA.

46.7

4.45113.0

4.97126.2

E-CoilViewStandard

Coil View

HYDRAFORCE®

MATERIALS TO ORDER

SV10-47F__ - __ __ __ - __ - __ __ __ __ __


SAE 6 6TSAE 8 8T





OptionNone (Blank)
















VoltageStd. Coil



terminations only


DESCRIPTIONA solenoid-operated, 5-way, 3-position, screw-in hydraulic cartridge valve withintegral load-sense port.

OPERATIONWhen de-energized, the SV10-57C blocks flow to all ports. When coil #1 is energized,flow is allowed from ➄ to ➁, and from ➃ to ➂. When coil #2 is energized, flow isallowed from ➄ to ➃, and from ➁ to ➂. Load sense is connected to port ➄ when thespool is in shifted positions.

FEATURES• Continuous-duty rated solenoid.• Hardened precision spool and cage for long life.• Optional coil voltages and terminations.• Optional waterproof E-Coils rated up to IP69K.• Optional manual override.• Efficient wet-armature construction.• Cartridges are voltage interchangeable.• Unitized, molded coil design.

RATINGSOperating Pressure: 247 bar (3625 psi) with standard Buna N sealsFlow: 20 lpm (4 gpm) max. See performance chartInternal Leakage: 164 cc/minute (10 cu. in./minute) max. at 207 bar (3000 psi)Temperature: -40 to 120°C with standard Buna sealsCoil Duty Rating: Continuous from 85% to 115% of nominal voltageInitial Coil Current Draw at 20° C: Standard Coil: 1.67 amps at 12 VDC; 0.18 amps


7.4 to 420 cSt (50 to 2000 sus)Installation: No restrictions; See page 9.020.1Cavity: VC10-5; See page 9.110.1Cavity Tool: CT10-5XX; See page 8.600.1Seal Kit: SK10-5X-MMMM; See page 8.650.1Coil Nut: Part No. 7004400; Coil Spacer for E-Coils: Part No. 4539700For E-coils manufactured prior to 1-1-04, see page 3.400.1 for coil nut & spacer info.

SOLENOID VALVES

SV10-57C Spool, 5-Way, 3-Position . . .

SYMBOLS

1.580.1

USASI:

ISO:


6.9/100

5.5/80

4.1/60

2.8/40

1.4/20

3.81

7.52

11.43

15.14

FLOW lpm/gpm

PR

ES

SU

RE

DR

OP

bar

/psi

➄ to ➁, S1 energized: ———➄ to ➃, S2 energized: – – – –➃ to ➂, S1 energizedor ➁ to ➂, S2 energized: - - - - - -


5

4

3

2

1

DIMENSIONS

SV10-57C

1.580.2

INCHMILLIMETRE

1.0025.4

ACROSS

FLATSTORQUE:

24–26 ft-lbs (32.5–35.3 Nm)

max.

TORQUE:5–7 ft-lbs (6.8–9.5 Nm)max.

1.3634.5

2.6266.5

5.00127

1.4837.6

2.0050.8

1.9950.6

4.38111.3

0.7519.1

3.0677.7

5

44

3

22

1

1

5

3

0.348.7

4.00101.6

0.194.8

3.6392.1

1.6241.1

1.84DIA.

46.75.77

ManualOverride

"M"

ManualOverride

"B"

146.54.48

113.8

E-CoilViewStandard

Coil View

0.7519.1

ACROSSFLATS

HYDRAFORCE®

MATERIALS TO ORDER

Cartridge: Weight: 0.36 kg. (0.80 lbs.);Steel with hardened work surfaces.Zinc-plated exposed surfaces. Buna NO-rings and polyester elastomer back-up standard.

Standard Ported Body: Weight: 0.41 kg.(0.85 lbs.); Anodized high-strength6061 T6 aluminum alloy, rated to240 bar (3500 psi); See page 8.010.1.Steel and Ductile Iron bodies avail-able, dimensions may differ, consultfactory.

Standard Coils: Weight each: 0.27 kg.(0.60 lbs.); Unitized thermoplasticencapsulated, Class H high tempera-ture magnetwire; See page 3.200.1.

E-Coils: Weight each: 0.41 kg. (0.9 lbs.);Fully encapsulated with ruggedexternal metal shell; Rated up toIP69K with integral connectors;See page 3.400.1 for E-Coil retrofitapplications.

SV10-57C__ - __ __ __ - __ - __ __ __ __ __


SAE 6 6TSAE 8 8T


OptionNone (Blank)

Manual Override BManual Override M











VoltageStd. Coil



terminations only


for Load Sense Applications

DESCRIPTIONA solenoid-operated, 5-way, 3-position, screw-in hydraulic cartridge valve withintegral load-sense port.

OPERATIONWhen de-energized, the SV10-57D blocks flow at ➄ while allowing flow from both ➁and ➃ to ➂. When coil #1 is energized, flow is allowed from ➄ to ➁, and from ➃ to ➂.When coil #2 is energized, flow is allowed from ➄ to ➃, and from ➁ to ➂. Load senseis connected to port ➄ when the spool is in shifted positions.

FEATURES• Continuous-duty rated solenoid.• Hardened precision spool and cage for long life.• Optional coil voltages and terminations.• Optional waterproof E-Coils rated up to IP69K.• Optional manual override.• Efficient wet-armature construction.• Cartridges are voltage interchangeable.• Unitized, molded coil design.

RATINGSOperating Pressure: 247 bar (3625 psi) with standard Buna N sealsFlow: 20 lpm (4 gpm) max. See performance chartInternal Leakage: 164 cc/minute (10 cu. in./minute) max. at 207 bar (3000 psi)Temperature: -40 to 120°C with standard Buna sealsCoil Duty Rating: Continuous from 85% to 115% of nominal voltageInitial Coil Current Draw at 20° C: Standard Coil: 1.67 amps at 12 VDC; 0.18 amps


7.4 to 420 cSt (50 to 2000 sus)Installation: No restrictions; See page 9.020.1Cavity: VC10-5; See page 9.110.1Cavity Tool: CT10-5XX; See page 8.600.1Seal Kit: SK10-5X-MMMM; See page 8.650.1Coil Nut: Part No. 7004400; Coil Spacer for E-Coils: Part No. 4539700For E-coils manufactured prior to 1-1-04, see page 3.400.1 for coil nut & spacer info.

SOLENOID VALVES

SYMBOLS

1.581.1

USASI:

ISO:


6.9/100

5.5/80

4.1/60

2.8/40

1.4/20

3.81

7.52

11.43

15.14

FLOW lpm/gpm

PR

ES

SU

RE

DR

OP

bar

/psi

➄ to ➁, S1 energized: ———➄ to ➃, S2 energized: – – – –➃ to ➂, S1 energizedor ➁ to ➂, S2 energized: - - - - - -


5

4

3

2

1

SV10-57D Spool, 5-Way, 3-Position . . .

DIMENSIONS

SV10-57D

1.581.2

INCHMILLIMETRE

1.0025.4

ACROSS

FLATSTORQUE:

24–26 ft-lbs (32.5–35.3 Nm)

max.


1.3634.5

2.6266.5

5.00127

1.4837.6

2.0050.8

1.9950.6

4.38111.3

0.7519.1

3.0677.7

5

44

3

22

1

1

5

3

0.348.7

4.00101.6

0.194.8

3.6392.1

1.6241.1

1.84DIA.

46.75.77

ManualOverride

"M"

ManualOverride

"B"

146.54.48

113.8

E-CoilViewStandard

Coil View

0.7519.1

ACROSSFLATS

HYDRAFORCE®

MATERIALS TO ORDER

SV10-57D__ - __ __ __ - __ - __ __ __ __ __


SAE 6 6TSAE 8 8T












Cartridge: Weight: 0.36 kg. (0.80 lbs.);Steel with hardened work surfaces.Zinc-plated exposed surfaces. Buna NO-rings and polyester elastomer back-up standard.

Standard Ported Body: Weight: 0.41 kg.(0.85 lbs.); Anodized high-strength6061 T6 aluminum alloy, rated to240 bar (3500 psi); See page 8.010.1.Steel and Ductile Iron bodies avail-able, dimensions may differ, consultfactory.

Standard Coils: Weight each: 0.27 kg.(0.60 lbs.); Unitized thermoplasticencapsulated, Class H high tempera-ture magnetwire; See page 3.200.1.

E-Coils: Weight each: 0.41 kg. (0.9 lbs.);Fully encapsulated with ruggedexternal metal shell; Rated up toIP69K with integral connectors;See page 3.400.1 for E-Coil retrofitapplications.

VoltageStd. Coil



terminations only


OptionNone (Blank)

Manual Override BManual Override M


DESCRIPTIONA solenoid-operated, fi ve-way, three-position, direct acting, screw-in hydraulic cartridge valve with integral load-sense port.

OPERATIONWhen de-energized, the SV08-58C blocks fl ow between all work ports and load sense at port ➀ is vented to ➂. When coil #1 is energized, fl ow is allowed from ➄ to ➁ and from ➃ to ➂. When coil #2 is energized, fl ow is allowed from ➄ to ➃ and from ➁ to ➂. Load sense at port ➀ is connected to port ➄ when spool is in the shifted positions.

FEATURES• Continuous-duty rated solenoid.• Hardened precision spool and cage for long life.• Optional coil voltages and terminations.• Optional waterproof E-Coils rated up to IP69K.• Compact size.• Effi cient wet-armature construction.• Cartridges are voltage interchangeable.• Unitized, molded coil design.

RATINGSOperating Pressure: 241 bar (3500 psi)Proof Pressure: 345 bar (5000 psi)Flow: 13.3 lpm (3.5 gpm) maximum; see performance chartInternal Leakage: 197 cc/minute (12 cu. in./minute) max. at 207 bar (3000 psi)Temperature: -40 to 120°C with standard Buna sealsCoil Duty Rating: Continuous from 85% to 115% of nominal voltageInitial Coil Current Draw at 20° C: Standard Coil: 1.2 amps at 12 VDC;



7.4 to 420 cSt (50 to 2000 sus); See Temperature and Oil Viscosity, page 9.060.1Installation: No restrictions; See page 9.020.1Cavity: VC08-5; See page 9.108.1Cavity Tool: CT08-5XX; See page 8.600.1Seal Kit: SK08-5X-MMM; See page 8.650.1Coil Nut: Part No. 7004400Coil Spacer: Part No. 4534720For E-coils manufactured prior to 1-1-04, see page 3.400.1 for coil nut & spacer info.


SYMBOLS

1.584.1

USASI/ISO:


SOLENOID VALVES

HYDRAFORCE.com®

24.1/350

20.7/300

17.2/250

13.8/200

10.3/150

6.9/100

3.4/50

FLOW lpm/gpm

PR

ES

SU

RE

DR

OP

bar

/psi

Differential Pressure vs. Flow32 cSt/150 sus oil at 40°C

1.90.5

3.81.0

5.71.5

7.62.0

9.52.5

11.43.0

13.33.5

5 to 4

5 to 2

4 to 32 to 3

241/3500

207/3000

172/2500

138/2000

103/1500

69/1000

34.5/500PR

ES

SU

RE

bar

/psi

Performance Range

FLOW lpm/gpm

1.90.5

3.81.0

5.71.5

7.62.0

9.52.5

11.43.0

13.33.5

RP



DIMENSIONS

SV08-58C

1.584.2


®HYDRAFORCE

HYDRAFORCE.com®

SV08-58C__ - __ __ __ - __ - __ __ __ __ __

TO ORDER


Termination (VDC) Std. Coil DS Dual Spades DG DIN 43650 DL Leadwires (2) DL/W Leads w/Weatherpak®


Termination (VAC) Std. Coil AG DIN 43650 AP 1/2 in. Conduit

Termination (VDC) E-Coil ER Deutsch DT04-2P (IP69K Rated) EY Metri-Pack® 150 (IP69K Rated)




12 12 VDC 24 24 VDC 36 36 VDC 48 48 VDC 24 24 VAC 115 115 VAC 230 230 VAC**Includes Std. Coil Nut† DS, DW or DL

terminations only.

MATERIALS



Standard Coil: Weight each: 0.11 kg. (0.25 lbs.); Unitized thermoplastic encapsulated, Class H high temperature magnetwire. See page 3.200.1



Option None (Blank)

0.8822.2

0.7519.1

0.6516.5

1.2331.2

E-CoilView

StandardCoil View

3.3885.9


4.05102

2.7168.7 2.291

58.2

1.17229.8

0.60915.5

1.73144.0

3.2582.6

0.3448.74

4.05102

3.62592.1

2.0050.8

1.4035.6

1.27032.3

0.1884.8

1.41DIA.

35.8

RP



DESCRIPTIONA solenoid-operated, fi ve-way, three-position, direct acting, screw-in hydraulic cartridge valve with integral load-sense port.

OPERATIONWhen de-energized, the SV10-58C blocks fl ow between all work ports and load sense at port ➀ is vented to ➂. When coil #1 is energized, fl ow is allowed from ➄ to ➁ and from ➃ to ➂. When coil #2 is energized, fl ow is allowed from ➄ to ➃ and from ➁ to ➂. Load sense at port ➀ is connected to port ➄ when spool is in the shifted positions.

FEATURES• Continuous-duty rated solenoid.• Hardened precision spool and cage for long life.• Optional coil voltages and terminations.• Optional waterproof E-Coils rated up to IP69K.• Optional manual override.• Effi cient wet-armature construction.• Cartridges are voltage interchangeable.• Unitized, molded coil design.

RATINGSOperating Pressure: 247 bar (3625 psi) with standard Buna N sealsFlow: 30.3 lpm (8 gpm) maximum; see performance chartsInternal Leakage: 164 cc/minute (10 cu. in./minute) max. at 207 bar (3000 psi)Temperature: -40 to 120°C with standard Buna sealsCoil Duty Rating: Continuous from 85% to 115% of nominal voltageInitial Coil Current Draw at 20° C: Standard Coil: 1.67 amps at 12 VDC; 0.18 amps

at 115 VAC (full wave rectifi ed). E-Coil: 1.6 amps at 12 VDC; 0.8 amps at 24 VDCMinimum Pull-in Voltage: 85% of nominal at 207 bar (3000 psi)Filtration: See page 9.010.1Fluids: Mineral-based or synthetics with lubricating properties at viscosities of

7.4 to 420 cSt (50 to 2000 sus); See Temperature and Oil Viscosity, page 9.060.1Installation: No restrictions; See page 9.020.1Cavity: VC10-5; See page 9.110.1Cavity Tool: CT10-5XX; See page 8.600.1Seal Kit: SK10-5X-MMMM; See page 8.650.1Coil Nut: Part No. 7004400; Coil Spacer for E-Coils: Part No. 4539700


SYMBOLS

1.584.1

USASI/ISO:


SOLENOID VALVES

HYDRAFORCE.com®

5

4

3

2

1

27.6/4001 to 3

5 to 4

5 to 2

2 to 3

4 to 3

24.1/350

20.7/300

17.2/250

13.8/200

10.3/150

6.9/100

3.4/50

FLOW lpm/gpm

PR

ES

SU

RE

DR

OP

bar

/psi

Pressure Drop vs. Flow32 cSt/150 sus oil at 40 C

3.81

7.62

11.43

15.14

18.95

22.76

26.57

30.38

276/4000

241/3500

207/3000

172/2500

138/2000

103/1500

69/1000

34.5/500

INLE

T P

RE

SS

UR

E b

ar/p

si

Minimum Load or Maximum Pressure DifferentialNo Manual Override: Shaded • With Manual Override: Hatched

FLOW lpm/gpm

3.81

7.62

11.43

15.14

18.95

22.76

26.57

30.38

RP



DIMENSIONS

SV10-58C

1.584.2

INCHMILLIMETRE

1.0025.4

ACROSS

FLATSTORQUE:

24–26 ft-lbs (32.5–35.3 Nm)

max.


1.3634.5

2.6266.5

5.00127

1.4837.6

2.0050.8

1.9950.6

4.38111.3

0.7519.1

3.0677.7

5

44

3

22

1

1

5

3

0.348.7

4.00101.6

0.194.8

3.6392.1

1.6241.1

1.84DIA.

46.75.77

ManualOverride

"M"

ManualOverride

"B"

146.54.48

113.8

E-CoilViewStandard

Coil View

0.7519.1

ACROSSFLATS


®HYDRAFORCE

HYDRAFORCE.com®

SV10-58C__ - __ __ __ - __ - __ __ __ __ __

TO ORDER










terminations only.

MATERIALS






Option None (Blank)

Manual Override B Manual Override M


RP



DESCRIPTIONA solenoid-operated, fi ve-way, three-position, motor-spool-type, screw-in hydraulic cartridge valve with integral load-sense port.

OPERATIONWhen de-energized, the SV08-58D blocks inlet fl ow at port ➄ while load sense at port ➀ is vented to port ➂, and ports ➁ and ➃ are connected to port ➂. When coil #1 is energized, fl ow is allowed from ➄ to ➁ and from ➃ to ➂. When coil #2 is energized, fl ow is allowed from ➄ to ➃ and from ➁ to ➂. Load sense at ➀ is connected to port ➄ when spool is in shifted postitions.

FEATURES• Continuous-duty rated solenoid.• Hardened precision spool and cage for long life.• Optional coil voltages and terminations.• Optional waterproof E-Coils rated up to IP69K.• Compact size.• Effi cient wet-armature construction.• Cartridges are voltage interchangeable.• Unitized, molded coil design.

RATINGSOperating Pressure: 241 bar (3500 psi)Proof Pressure: 345 bar (5000 psi)Flow: 13.3 lpm (3.5 gpm) maximum; see performance chartInternal Leakage: 197 cc/minute (12 cu. in./minute) max. at 207 bar (3000 psi)Temperature: -40 to 120°C with standard Buna sealsCoil Duty Rating: Continuous from 85% to 115% of nominal voltageInitial Coil Current Draw at 20° C: Standard Coil: 1.2 amps at 12 VDC;



7.4 to 420 cSt (50 to 2000 sus); See Temperature and Oil Viscosity, page 9.060.1Installation: No restrictions; See page 9.020.1Cavity: VC08-5; See page 9.108.1Cavity Tool: CT08-5XX; See page 8.600.1Seal Kit: SK08-5X-MMM; See page 8.650.1Coil Nut: Part No. 7004400Coil Spacer: Part No. 4534720For E-coils manufactured prior to 1-1-04, see page 3.400.1 for coil nut & spacer info.


SYMBOLS

1.584.1

USASI/ISO:


SOLENOID VALVES

HYDRAFORCE.com®

24.1/350

20.7/300

17.2/250

13.8/200

10.3/150

6.9/100

3.4/50

FLOW lpm/gpm

PR

ES

SU

RE

DR

OP

bar

/psi

Differential Pressure vs. Flow32 cSt/150 sus oil at 40°C

1.90.5

3.81.0

5.71.5

7.62.0

9.52.5

11.43.0

13.33.5

5 to 4

5 to 2

4 to 3

2 to 3

241/3500

207/3000

172/2500

138/2000

103/1500

69/1000

34.5/500PR

ES

SU

RE

bar

/psi

Performance Range

FLOW lpm/gpm

1.90.5

3.81.0

5.71.5

7.62.0

9.52.5

11.43.0

13.33.5

RP



DIMENSIONS

SV08-58D

1.584.2


®HYDRAFORCE

HYDRAFORCE.com®

SV08-58D__ - __ __ __ - __ - __ __ __ __ __

TO ORDER










terminations only.

MATERIALS






Option None (Blank)

0.8822.2

0.7519.1

0.6516.5

1.2331.2

E-CoilView

StandardCoil View

3.3885.9


4.05102

2.7168.7 2.291

58.2

1.17229.8

0.60915.5

1.73144.0

3.2582.6

0.3448.74

4.05102

3.62592.1

2.0050.8

1.4035.6

1.27032.3

0.1884.8

1.41DIA.

35.8

RP



DESCRIPTIONA solenoid-operated, fi ve-way, three-position, motor-spool-type, screw-in hydraulic cartridge valve with integral load-sense port.

OPERATIONWhen de-energized, the SV10-58D blocks inlet fl ow at port ➄ while load sense at port ➀ is vented to port ➂, and ports ➁ and ➃ are connected to port ➂. When coil #1 is energized, fl ow is allowed from ➄ to ➁ and from ➃ to ➂. When coil #2 is energized, fl ow is allowed from ➄ to ➃ and from ➁ to ➂. Load sense at ➀ is connected to port ➄ when spool is in shifted postitions.

FEATURES• Continuous-duty rated solenoid.• Hardened precision spool and cage for long life.• Optional coil voltages and terminations.• Optional waterproof E-Coils rated up to IP69K.• Optional manual override.• Effi cient wet-armature construction.• Cartridges are voltage interchangeable.• Unitized, molded coil design.

RATINGSOperating Pressure: 247 bar (3625 psi) with standard Buna N sealsFlow: 30.3 lpm (8 gpm) maximum; see performance chartsInternal Leakage: 164 cc/minute (10 cu. in./minute) max. at 250 bar (3625 psi)Temperature: -40 to 120°C with standard Buna sealsCoil Duty Rating: Continuous from 85% to 115% of nominal voltageInitial Coil Current Draw at 20° C: Standard Coil: 1.67 amps at 12 VDC; 0.18 amps

at 115 VAC (full wave rectifi ed). E-Coil: 1.6 amps at 12 VDC; 0.8 amps at 24 VDCMinimum Pull-in Voltage: 85% of nominal at 207 bar (3000 psi)Filtration: See page 9.010.1Fluids: Mineral-based or synthetics with lubricating properties at viscosities of

7.4 to 420 cSt (50 to 2000 sus); See Temperature and Oil Viscosity, page 9.060.1Installation: No restrictions; See page 9.020.1Cavity: VC10-5; See page 9.110.1Cavity Tool: CT10-5XX; See page 8.600.1Seal Kit: SK10-5X-MMMM; See page 8.650.1Coil Nut: Part No. 7004400; Coil Spacer for E-Coils: Part No. 4539700


SYMBOLS

1.586.1

USASI/ISO:


SOLENOID VALVES

HYDRAFORCE.com®

5

4

3

2

1

34.5/500

27.6/400

31.0/4501 to 3

5 to 45 to 2

2 to 3

4 to 3

24.1/350

20.7/300

17.2/250

13.8/200

10.3/150

6.9/100

3.4/50

FLOW lpm/gpm

PR

ES

SU

RE

DR

OP

bar

/psi


3.81

7.62

11.43

15.14

18.95

22.76

26.57

30.38

276/4000

241/3500

207/3000

172/2500

138/2000

103/1500

69/1000

34.5/500

INLE

T P

RE

SS

UR

E b

ar/p

si

Minimum Load or Maximum Pressure DifferentialNo Manual Override: Shaded • With Manual Override: Hatched

FLOW lpm/gpm

3.81

7.62

11.43

15.14

18.95

22.76

26.57

30.38


RP


DIMENSIONS

SV10-58D

1.586.2

INCHMILLIMETRE

1.0025.4

ACROSS

FLATSTORQUE:

24–26 ft-lbs (32.5–35.3 Nm)

max.


1.3634.5

2.6266.5

5.00127

1.4837.6

2.0050.8

1.9950.6

4.38111.3

0.7519.1

3.0677.7

5

44

3

22

1

1

5

3

0.348.7

4.00101.6

0.194.8

3.6392.1

1.6241.1

1.84DIA.

46.75.77

ManualOverride

"M"

ManualOverride

"B"

146.54.48

113.8

E-CoilViewStandard

Coil View

0.7519.1

ACROSSFLATS


®HYDRAFORCE

HYDRAFORCE.com®

SV10-58D__ - __ __ __ - __ - __ __ __ __ __

TO ORDER










terminations only.

MATERIALS






Option None (Blank)

Manual Override B Manual Override M



RP


SOLENOID VALVES


DESCRIPTIONA solenoid-operated, 2-position, 6-way, direct-acting spool-type, screw-in hydrauliccartridge valve. It is intended for use as a selector valve in selector or series/paralleldrive circuits.

OPERATIONWhen de-energized, the SV12-60 allows bi-directional flow between ➄ and ➅, andbetween ➀ and ➁, while blocking flow at ➂ and ➃. When energized, the spool shiftsto allow bidirectional flow between ➃ and ➄ and between ➂ and ➁, while blockingflow at ➀ and ➅.

FEATURES• Heavy-duty water resistant E-Coils rated up to IP69K.• Hardened spool and cage for long life.• Optional coil voltages and terminations.• All ports may be fully pressurized.• External metal-shell coil design.

RATINGSOperating Pressure: 240 bar (3500 psi) max.Flow: Up to 45.4 lpm (12 gpm); See Performance ChartLeakage: 295 cc/minute (18 cu. in./minute) at 240 bar (3500 psi)Temperature: -40 to 120°C with Buna N sealsCoil Duty Rating: See ChartResponse Time: Pull-In: 135 msec; Drop-Out: 30 msecInitial Coil Current Draw at 20°C: 2.8 amps at 12 VDCFiltration: See page 9.010.1Fluids: Mineral-based or synthetics with lubricating properties at viscosities of

7.4 to 420 cSt (50 to 2000 sus)Installation: No restrictions; See page 9.020.1Cavity: VC12-6; See page 9.112.1Cavity Tool: CT12-6XX; See page 8.600.1Seal Kit: SK12-6X-MMMMM; See page 8.650.1E-Coil Nut: Part No. 7085180

USASI/ISO:


SYMBOLS

1.620.1

4

3

2

1

5

6

6.9/100

5.2/75

12.1/175

8.6/125

10.3/150

3.4/50

1.7/25

30.28

22.76

37.810

15.14

7.62

45.412

FLOW lpm/gpm

PR

ES

SU

RE

DR

OP

bar

/psi


➄ to ➃

➄ to ➅

➁ to ➀

➁ to ➂

276/4000

207/3000

138/2000

69/1000

22.76

34.19

11.43

45.412

FLOW lpm/gpm

PR

ES

SU

RE

bar

/psi


Series/Parallel: //// ; Selector: \\\\32 cSt/150 sus oil at 40°C

110

120

60 7050403020100-20 -10-30-40

100

80

90

70

60

50% O

F R

AT

ED

VO

LTA

GE




Operating Range

SV12-60

DIMENSIONS

MATERIALS


Standard Ported Body: Anodized high-strength 6061 T6 aluminum alloy,rated to 240 bar (3500 psi); Consultfactory for availability.

E-Coil: Weight: 1.36 kg. (3.0 lbs.); Fullyencapsulated with rugged externalmetal shell; Rated up to IP69K withintegral connectors; See Page3.400.1.

TO ORDER

SV12-60 __ __ __ - __ - __ __ __ __


SAE 6 6TSAE 8 8T

SAE 10 10T

1.620.2


Voltage0 Less Coil12 12 VDC24 24 VDC36 36 VDC48 48 VDC

4

3

2

1

1

5

6

4.17105.9

3.95100.3

1.1027.9

1.7644.8

TORQUE:10 ft-lbs.

(13.4 Nm) max.

ACROSS FLATS

31.81.25

1.25

ACROSS FLATSTORQUE:60 ft-lbs.(80 Nm) max.

31.8

MILLIMETREINCH

HY

DR

AF

OR

CE

1.7243.6

2.4361.7

3.4387.1

2

3

4

5

6

1.0125.7

2.3559.8

3.6993.8

0.348.60.19

4.8

1.6842.8

3.0276.8

4.75120.7

5.50139.7

3.0577.5

HYDRAFORCE®



IP69K Rated



DESCRIPTIONA solenoid-operated, 2-position, 6-way, direct-acting spool-type, screw-in hydrauliccartridge valve. It is intended for use as a selector valve in selector or series/paralleldrive circuits.

OPERATIONWhen de-energized, the SV80-61 blocks flow to ➄ and ➅, and allows flow between ➃and ➂, and between ➀ and ➁. When energized, the spool shifts to block flow to ports➁ and ➂, while allowing flow between ➃ and ➄, and between ➀ and ➅.

Note: In circuits where this valve is used as a selector valve to direct flow betweentwo cylinders of unequal area ratios, the cylinder head sides should be connected toports ➂ and ➄, and the rod sides to ports ➁ and ➅.

FEATURES• Continuous-duty rated solenoid.• Hardened parts for long life.• Optional coil voltages and terminations.• Optional waterproof E-Coils rated up to IP69K.• Cartridges are voltage interchangeable.

RATINGSOperating Pressure: 207 bar (3000 psi) with standard Buna N sealsFlow: 7.6 lpm (2 gpm) max. See performance chartInternal Leakage: 164 ml/minute (10 cu. in./minute) at 207 bar (3000 psi)Temperature: -40 to 120°C with standard Buna sealsFiltration: Recommend ISO 4406 16/13; See page 9.010.1Fluids: Mineral-based or synthetics with lubricating properties at viscosities of

7.4 to 420 cSt (50 to 2000 sus)Installation: No restrictions; See page 9.020.1Cavity: VC10-6; See page 9.110.1Cavity Tool: CT10-6XX; See page 8.600.1Seal Kit: SK80-6X-MMMMM; See page 8.650.1Coil Nut: Part No. 7004400

SOLENOID VALVES

SYMBOLS

1.640.1

USASI/ISO:


SV80-61 Spool, 6-Way, 2-Position, Selector Valve

1.4/20

2.8/40

2.1/30

0.7/10

1.24.5

1.66.1

0.83.0

0.41.5

2.07.6

FLOW lpm/gpm

PR

ES

SU

RE

DR

OP

bar

/psi

PRESSURE DROP vs. FLOWEnergized - - -; De-Energized ——


➅ to ➀ e

➁ to ➀ d

➃ to ➄ e ➃ to ➂ d

207/3000

138/2000

69/1000

3.00.8

4.51.2

6.11.6

1.50.4

7.62.0

FLOW lpm/gpm

PR

ES

SU

RE

bar

/psi

OPERATING LIMITSSelector Circit with Inlet at ➃, or Series/Parallel Circuit: ////32 cSt/150 sus oil at 40°C

207/3000

138/2000

69/1000

3.00.8

4.51.2

6.11.6

1.50.4

7.62.0

FLOW lpm/gpm

PR

ES

SU

RE

bar

/psi

OPERATING LIMITSSelector Circuit with Inlet at ➀: \\\\


DIMENSIONS

SV80-61

1.640.2

HYDRAFORCE®

OptionNone (Blank)

MATERIALS




VoltageStd. Coil



terminations only

SV80-61__ - __ __ __ - __ - __ __ __ __ __

TO ORDER













3.6392.1

2.0050.8

1.4035.6

4.00101.6

1.8246.2

E-CoilShown

E-CoilShown

3.7093.9

1.00

ACROSSFLATS

25.4

0.75ACROSS FLATSDIA.TORQUE: 5–7 ft-lbs(6.8 –9.5 Nm)

TORQUE:25–27 ft-lbs(33.9 –36.6 Nm)

19.0

1.3634.5

2.6266.5

5.00127

1.5038.1

1.9950.6 4.38

111.3

3.2382.0

0.7519.1

5

3

2

1

6

45

3

2

1

6

4

0.348.70.19

4.8

1.4135.8


SAE 6 6TSAE 8 8T

DESCRIPTIONAn economical drop-in-style, direct-acting, balanced spool, 2-position, 3-way,directional control valve. It is well suited for use in specialized low-pressure pilotsystems or power shift transmission control.

OPERATIONWhen de-energized, the SV98-T39 allows flow from ➁ to ➀, while blocking flow at ➂.

When energized, the cartridge's spool shifts to open from ➂ to ➁, while blocking flowout ➀. Pressure at ➀ (tank) should not exceed 3.4 bar (50 psi).

The coil is an integral part of the valve and is not serviceable.

FEATURES• Economical drop-in style.• Integral waterproof coil standard.• 12 or 24 VDC coils.• Several push-on termination options.

RATINGSOperating Pressure: 45 bar (650 psi)Flow: 30 lpm (8 gpm)Internal Leakage: 60 ml/minute (3.7 cu. in./minute)Temperature: -40 to 120°CCoil Duty Rating: Continuous from 85% to 115% of nominal voltageResponse Time: First indication of change of state with 100% voltage

and flow rating: Pull-in: 50 ms; Drop-out: 30 ms.Initial Coil Current Draw at 20°C: 1.68 amps at 12 VDCMinimum Pull-in Voltage: 85% of nominal at 30 bar (435 psi)Filtration: See page 9.010.1Fluids: Mineral-based or synthetics with lubricating properties at viscosities of

7.4 to 420 cSt (50 to 2000 ssu)Installation: Flange MountFlange Mounting Screws: M5 x 8; Part No. 4000039Cavity: VC-T001; See page 9.110.1Cavity Tool: CT-T001; See page 8.600.1Seal Kit: SK98-T39X-000; See page 8.650.1

SOLENOID VALVES

SV98-T39 Spool, 3-Way, 2-Position, Drop-In-Style

SYMBOLS

USASI/ISO:


1.700.1

8.3/120

6.9/100

5.5/80

4.1/60

2.8/40

PR

ES

SU

RE

DR

OP

bar

/psi

Pressure Drop vs. Flow32 cSt/150 ssu oil at 40°C

7.52

3.81

11.43

FLOW lpm/gpm

15.14

18.95

26.57

22.76

30.28

1.4/20

➂ to

➁

➁ to ➀

1

2

3

SV98-T39

DIMENSIONS

1.700.2

1.28

30°

32.5

0.8521.5

1.1027.8

1.9549.6

1.71

Tank

Work Port

1

43.4

1.16DIA.

MOUNTING SCREWTORQUE: 2 to 3 ft-lbs

(3 to 4 Nm)

29.5

0.6416.3

2.5063.5

0.6315.9

0.8521.5

0.8521.5

1.2531.8

INCHMILLIMETRE

1

2

PressureInlet Port

3

30°

1.2531.8

2.5063.5

1.3434.0

2

3

HYDRAFORCE®

OptionNone (Blank)

233µ screen S on inlet port

MATERIALS

Cartridge including Coil: Weight:0.23 kg. (0.50 lbs.); Steel withhardened work surfaces. Zinc-Nickel plated exposed surfaces;HNBR O-rings standard. Coil isencapsulated, class H high-temperature magnetwire, withzinc-nickel plated shell.

Standard Ported Test Body:Weight: 0.11 kg. (0.25 lbs.);Anodized high-strength 6061 T6aluminum alloy, rated to 240 bar(3500 psi); See page 8.008.1.

SV98-T39 __ - __ __ - __ __ - __ __TO ORDER

Voltage 12 12 VDC 24 24 VDC

TerminationEJ Amp Junior TimerEY Metri-Pack® 150.2AER Deutsch DT04-2P


SAE 6 6T


DESCRIPTIONAn economical drop-in-style, direct-acting, balanced spool, two-position, four-way, directional control valve. It is well suited for use in specialized low-pressure pilot systems or power shift transmission control.

OPERATIONWhen de-energized, the SV98-T40 allows fl ow from ➂ to ➁ and from ➃ to ➀. When energized, the cartridge’s spool shifts to allow fl ow from ➁ to ➀ and from ➂ to ➃. Pressure at ➀ (tank) should not exceed 3.4 bar (50 psi).The coil is an integral part of the valve and is not serviceable.

FEATURES• Economical drop-in style.• Integral waterproof coil standard.

See page 3.400.1 for a description of tests conducted to verify coil waterproofi ng.• 12 or 24 VDC coils.• Several push-on termination options.

RATINGSOperating Pressure: up to 30 bar (435 psi)Flow: 30 lpm (8 gpm)Internal Leakage: 70 ml/minute (4.3 cu. in./minute) maximum from inlet to tank

at 30 bar (435 psi)Temperature: -40 to 120°CCoil Duty Rating: Continuous from 85% to 115% of nominal voltageResponse Time: First indication of change of state with 100% voltage

and fl ow rating: Pull-in: 50 ms; Drop-out: 30 ms.Initial Coil Current Draw at 20°C: 1.68 amps at 12 VDCMinimum Pull-in Voltage: 85% of nominal at 30 bar (435 psi)Filtration: See page 9.010.1Fluids: Mineral-based or synthetics with lubricating properties at viscosities of

7.4 to 420 cSt (50 to 2000 sus); See Temperature and Oil Viscosity, page 9.060.1Installation: Flange MountFlange Mounting Screws: M5 x 8; Part No. 4000039 (not provided with valve)Cavity: VC-T004; See page 9.111.1Cavity Tool: CT-T004R0-x-G; See page 8.600.1Seal Kit: SK98-T4N-000; See page 8.650.1

SV98-T40 Spool, 4-Way, 2-Position, Drop-In-Style

SYMBOLS

USASI/ISO:


1.704.1

SOLENOID VALVES

HYDRAFORCE.com®

1

2

3

4

8.3/120

9.7/140

11.0/160

6.9/100

5.5/80

4.1/60

2.8/40

PR

ES

SU

RE

DR

OP

bar

/psi


7.52

3.81

11.43

FLOW lpm/gpm

15.14

18.95

26.57

22.76

30.28

1.4/20

4 to 1

3 to 2

3 to 4

2 to 1

RP



SV98-T40

DIMENSIONS

1.704.2

Option None (Blank)

233µ screen S on inlet port

MATERIALS

Cartridge including Coil: Weight: 0.26 kg. (0.57 lbs.) Steel with hardened work surfaces. Zinc-Nickel plated exposed surfaces. HNBR O-rings standard. Coil is encapsulated, class H high-temperature magnetwire, with zinc-nickel plated shell.

Standard Ported Test Body: Weight: 0.11 kg. (0.25 lbs.) Anodized high-strength 6061 T6 aluminum alloy, rated to 207 bar (3000 psi). See page 8.010.1.

Mounting Screws: Must be ordered separately: Part No. 4001015

SV98-T40 __ - __ __ - __ __ - __ __

TO ORDER

Voltage 12 12 VDC 24 24 VDC

Termination DJ Amp Junior Timer Y2A Metri-Pack® 150.2A DR Deutsch DT04-2P

Porting Cartridge Only 0 SAE 6 6T


®HYDRAFORCE

HYDRAFORCE.com®

1.31

30

33.2

0.8521.5

1.1027.8

1.9549.6

2.17

Tank

ScreenOptionShown

Work Port

1

55.0

1.16DIA.

FLANGE MOUNTING SCREW TORQUE:

2 to 3 ft-lbs (3 to 4 Nm)

29.5

INCHMILLIMETRE

2

Work Port

Inlet Port3

4

1.4336.3

1.7544.5

1.1428.9

3.2582.6

0.7218.2

1.2030.5

0.6215.7

1.7043.2

2.4371.7

0.9724.60.29

7.37

2.9374.4

2.3760.1

0.297.3

0.4110.4

4

2

1

3

0.85

21.50.85

21.5

30

RP




DESCRIPTIONA solenoid-operated, two-way, pilot-operated, poppet-type, normally closed, screw-in hydraulic cartridge valve with outlet fl ow check, designed for low leakage in load holding applications.

OPERATIONWhen de-energized, the SVCV08-20 blocks fl ow from ➁ to ➀ and from ➀ to ➁.When energized, the cartridge’s poppet lifts to open the ➁ to ➀ fl ow path, while continuing to block fl ow from ➀ to ➁.The SVCV08-20 is designed to fi t into the VC08-3 cavity with the normal inlet at cav-ity port 3 (valve port ➁), the outlet at cavity port ➀ (valve port ➀), and cavity port ➁ blocked. The pressure drop will be substantially higher if cavity port ➁ is selected as an alternate outlet port.Operation of Manual Override Option: To override, push button in, twist counter-clockwise 180°, and release. In this position, the valve will remain open. To return to normal operation, push button in, twist clockwise 180°, and release. Override will be detented in this position.

FEATURES• Continuous-duty rated coil.• Hardened seat for long life and low leakage.• Optional coil voltages and terminations.• Manual override option.• Cartridges are voltage interchangeable.• Optional waterproof E-Coils rated up to IP69K.• Industry common cavity.• Compact size.

RATINGSOperating Pressure: 207 bar (3000 psi)Rated Flow: 22.7 lpm (6 gpm)Reverse Flow Check Valve Spring: 0.69 bar (10 psi)Maximum Internal Leakage: ➁ to ➀: 5 drops/minute at 207 bar (3000 psi);

➀ to ➁: 10 drops/minute at 207 bar (3000 psi)Temperature: -40 to 120°C with standard Buna sealsCoil Duty Rating: Continuous from 85% to 115% of nominal voltageResponse Time: First indication of change of state with 100% voltage supplied at

80% of nominal fl ow rating:Energized: 40 msec.; De-energized: 46 msec.

Initial Coil Current Draw at 20°C: Standard Coil: 1.2 amps at 12 VDC; 0.13 amps at 115 VAC (full wave rectifi ed); E-Coil: 1.4 amps at 12 VDC; 0.7 amps at 24 VDC


7.4 to 420 cSt (50 to 2000 sus); See Temperature and Oil Viscosity, page 9.060.1Installation: No restrictions; See page 9.020.1Cavity: VC08-3; See page 9.108.1Cavity Tool: CT08-3XX; See page 8.600.1Seal Kit: SK08-3X-M; See page 8.650.1Coil Nut: Part No. 7004400

SYMBOLS

ISO:


1.115.1

8.6/125

6.9/100

5.2/75

3.4/50

1.7/25

11.43

7.62

3.81

15.14

18.95

FLOW lpm/gpm

PR

ES

SU

RE

DR

OP

bar

/psi



22.76

10.3/150

SOLENOID VALVES

HYDRAFORCE.com®

Expanded:

RP



SVCV08-20

DIMENSIONS

1.115.2

1.88


TORQUE19–21 ft-lb

(25.8–28.5 Nm)

47.8

1.6341.3

E-CoilView

1.4035.6

1.41


DIA.35.8

Standard Coil View

Plugged

0.4310.9


SVCV08-20__ - __ __ __ - __ - __ __ __ __ __

TO ORDER










terminations only.

MATERIALS




E-Coil: Weight: 0.14 kg. (0.3 lbs.); Perfect wound, fully encapsulated with rugged external metal shell; Rated up to IP69K with integral connectors. See page 3.400.1

Porting Cartridge Only 0 SAE 6 6T SAE 8 8T 1/4 in. BSP* 2B


®HYDRAFORCE

HYDRAFORCE.com®

Option None (Blank)

Manual Override M

RP




DESCRIPTIONA solenoid-operated, two-way, pilot-operated, poppet-type, normally closed, screw-in hydraulic cartridge valve with outlet fl ow check, designed for low leakage in load holding applications.

OPERATIONWhen de-energized, the SVCV12-20 blocks fl ow from 2 to 1 and from 1 to 2.When energized, the cartridge’s poppet lifts to open the 2 to 1 fl ow path, while continuing to block fl ow from 1 to 2.The SVCV12-20 is designed to fi t into the VC12-3 cavity with the normal inlet at cavity port 3 (valve port 2), the outlet at cavity port 1 (valve port 1), and cavity port 2 blocked. The pressure drop will be substantially higher if cavity port 2 is selected as an alternate outlet port. At fl ows greater than 56.8 lpm (15 gpm) pressure drop will be lower if the optional port 2 is connected to port 1.

FEATURES• Continuous-duty rated coil.• Hardened seat for long life and low leakage.• Optional coil voltages and terminations.• Cartridges are voltage interchangeable.• Optional waterproof E-Coils rated up to IP69K.• Cost effective cavity.

RATINGSOperating Pressure: 240 bar (3500 psi)Rated Flow: 113.6 lpm (30 gpm)Maximum Internal Leakage: 2 to 1: 5 drops/minute at 207 bar (3000 psi);

1 to 2: 10 drops/minute at 207 bar (3000 psi)Temperature: -40 to 100°C (-40° to 212°F) with standard Buna N seals

-26 to 204°C (-15°F to 400°F) with Fluorocarbon seals-54 to 107°C (-65°F to 225°F) with Polyurethane seals

Coil Duty Rating: Continuous from 85% to 115% of nominal voltageInitial Coil Current Draw at 20°C: Standard Coil: 1.67 amps at 12 VDC;

0.13 amps at 115 VAC (full wave rectifi ed); E-Coil: 1.7 amps at 12 VDC; 0.8 amps at 24 VDC



SYMBOLS

ISO:


1.117.7

SOLENOID VALVES

Expanded:

17.2/250

13.8/200

10.3/150

6.9/100

3.4/50

56.815

37.910

18.95

75.720

94.625

FLOW lpm/gpm

PR

ES

SU

RE

DR

OP

bar/p

si

Cartridge and Body32 cSt/150 sus oil at 40°C

113.630

20.7/300

24.1/350

Port 3 to Port 1(Port 2 Blocked)

Port 3to

Port 2

HYDRAFORCE.com�

RP



with Reverse Flow Check SVCV12-20

DIMENSIONS

1.117.8

SVCV12-20 - __ __ __ - __ - __ __ __ __ __TO ORDER





terminations only.

MATERIALSCartridge: Weight: 0.28 kg.

(0.62 lbs.); Steel with hardened work surfaces. Zinc-plated exposed surfaces; Buna N O-rings and back-ups standard.

Standard Ported Body: Weight: 0.98 kg. (2.15 lbs.); Anodized high-strength 6061 T6 alumi-num alloy, rated to 207 bar (3000 psi); Ductile iron bodies available; dimensions maydiffer. See page 8.012.1.

Standard Coil: Weight: 0.27 kg. (0.60 lbs.); Unitized thermo-plastic encapsulated, Class H high temperature magnetwire. See page 3.200.1.


Porting Cartridge Only 0 SAE 8 8T SAE 10 10T SAE 12 12T 1/2 in. BSP* 4B 3/4 in. BSP* 6B


1.6241.1

1.8446.7

1.0025.5

2.00

0.75 (19.1)Across Flats

1.25 (31.8)Across Flats

50.744.0

1.9950.6

1.4837.6

2.1253.8

3.2582.6

4.02102.2

3.6392.1

0.194.8

0.348.7

2.7870.5

2.4562.3

1.1529.2

E-CoilViewD-Coil View

4.02102.2

DIA.

Dia. 1.73

Torque:33-37 ft-lb

(44.9 - 50.3 Nm)

Torque:5-7 ft-lb

(6.8 - 9.5 Nm)


Optional

Optional



®HYDRAFORCE

HYDRAFORCE.com®

RP



SVCV08-21 Poppet, 2-Way, Normally Open . . .

DESCRIPTIONA solenoid-operated, two-way, pilot-operated, poppet-type, normally open, screw-in hydraulic cartridge valve with outlet fl ow check, designed for low leakage in load holding applications.

OPERATIONWhen energized, the SVCV08-21 blocks fl ow from ➁ to ➀ and from ➀ to ➁.When de-energized, the cartridge’s poppet lifts to open the ➁ to ➀ fl ow path, while continuing to block fl ow from ➀ to ➁.The SVCV08-21 is designed to fi t into the VC08-3 cavity with the normal inlet at cavity port 3 (valve port ➁), the outlet at cavity port ➀ (valve port ➀), and with cavity port ➁ blocked.Operation of Manual Override Option: To override, push and hold override button.

FEATURES• Continuous-duty rated coil.• Hardened seat for long life and low leakage.• Optional coil voltages and terminations.• Cartridges are voltage interchangeable.• Manual override option.• Optional waterproof E-Coils rated up to IP69K.• Industry common cavity.• Compact size.

RATINGSOperating Pressure: 207 bar (3000 psi)Rated Flow: 22.7 lpm (6 gpm)Reverse Flow Check Valve Spring: 0.69 bar (10 psi)Maximum Internal Leakage: ➁ to ➀: 5 drops/minute at 207 bar (3000 psi);

➀ to ➁: 10 drops/minute at 207 bar (3000 psi)Temperature: -40 to 120°C with standard Buna sealsCoil Duty Rating: Continuous from 85% to 115% of nominal voltageResponse Time: First indication of change of state with 100% voltage supplied at

80% of nominal fl ow rating:Energized: 40 msec.; De-energized: 46 msec.

Initial Coil Current Draw at 20°C: Standard Coil: 1.2 amps at 12 VDC; 0.13 amps at 115 VAC (full wave rectifi ed); E-Coil: 1.4 amps at 12 VDC; 0.7 amps at 24 VDC



SYMBOLS

ISO:


1.125.1

5.2/75

4.1/60

3.1/45

2.1/30

1.0/15

11.43

7.62

3.81

15.14

18.95

FLOW lpm/gpm

PR

ES

SU

RE

DR

OP

bar

/psi



22.76

6.2/90

SOLENOID VALVES

HYDRAFORCE.com®

Expanded:

RP



SVCV08-21

DIMENSIONS

1.125.2

1.88


TORQUE19–21 ft-lb

(25.8–28.5 Nm)

47.82.2156.1

1.6341.3

E-CoilView

1.4035.6

1.41

COIL MUST BE INSTALLED WITH LETTERING UP

DIA.35.8

Standard Coil View

Plugged


SVCV08-21__ - __ __ __ - __ - __ __ __ __ __

TO ORDER










terminations only.

MATERIALS





Porting Cartridge Only 0 SAE 6 6T SAE 8 8T 1/4 in. BSP* 2B


®HYDRAFORCE

HYDRAFORCE.com®

Option None (Blank)

Manual Override without Knob P Manual Override with Knob K

RP



DESCRIPTIONA solenoid-operated, normally-closed, on/off, poppet-type, screw-in hydraulic cartridge valve incorporating an integral load-sense pressure port with isolation check.

OPERATIONWhen de-energized, the SVCL10-30 blocks flow at all ports. When energized, flow is allowed from 3 to 1 with a check-isolated load sense signal supplied at 2. Reverse flow is not allowed from 1 to 3.

NOTE: When using this valve in bridge circuits, seals should not be used on the pilot pistons of the pilot-operated check valves. This is to avoid trapping oil which would keep the pilot-operated check valve open.

FEATURES• Continuous-duty rated solenoid.• Hardened precision spool and cage for long life.• Optional coil voltages and terminations.• Efficient wet-armature construction.• All ports may be fully pressurized.• Cartridges are voltage interchangeable.• Optional waterproof E-Coils rated up to IP69K.• Unitized, molded coil design.• Reduce manifold space claim.

RATINGSOperating Pressure: 240 bar (3625 psi); Holding Pressure at 1: 350 bar (5000 psi)Flow: Up to 57 lpm (15 gpm)Internal Leakage: Ports 1 and 3: 5 drops/minute max. at 240 bar (3500 psi)

Port 2: 10 drops/minute max. at 240 bar (3500 psi)Operating Temperature: -40° to 121°C (-40° to 250°F) with Buna N -35° to 204°C (-31° to 400°F) with Fluorocarbon seals

-54 to 107°C (-65° to 225°F) with Polyurethane sealsCoil Duty Rating: Continuous from 85% to 115% of nominal voltageInitial Coil Current Draw at 20°C: Standard D-Coil: 1.67 amps at 12 VDC;



7.4 to 420 cSt (50 to 2000 sus); See Temperature and Oil Viscosity, page 9.060.1Installation: No restrictions; See page 9.020.1Cavity: VC10-3, Variation “B”; See page 9.110.1Cavity Tool: CT10-3XX; See page 8.600.1Seal Kit: SK10-3X-MM; See page 8.650.1Coil Nut: Part No. 7004400

SVCL10-30 Poppet, 3-Port, Normally Closed

SYMBOL

1.310.1


SOLENOID VALVES

HYDRAFORCE.com®

ISO:

Expanded:

➂ to ➀32 cSt/150 sus oil at 40°C

17.2/250

13.7/200

10.3/150

6.9/100

3.4/50

22.76

45.412

56.815

FLOW lpm/gpm

PR

ES

SU

RE

DR

OP

bar

/psi

11.43

34.19

➂ to ➁32 cSt/150 sus oil at 40°C

3.4/50

2.8/40

2.1/30

1.4/20

0.7/10

0.760.2

1.520.4

1.900.5

FLOW lpm/gpm

PR

ES

SU

RE

DR

OP

bar

/psi

0.380.1

1.140.3

U.S. Patent 7,921,880

RP



DIMENSIONS

SVCL10-30

1.310.2

TO ORDER

Cartridge: Weight: 0.18 kg. (0.40 lbs.); Steel with hardened work surfaces. Zinc-plated exposed surfaces. Buna N O-rings and polyester elastomer back-up standard.

Standard D-Coil: Weight: 0.27 kg. (0.60 lbs.); Unitized thermoplas-tic encapsulated, Class H high temperature magnetwire. See page 3.200.1.

E-Coil: Weight: 0.41 kg. (0.9 lbs.); Fully encapsulated with rugged external metal shell. Rated up to IP69K with integral connectors. Note: See page 3.400.1 for all E-Coil retrofit applications.

MATERIALS

®HYDRAFORCE

HYDRAFORCE.com®

1.6241.1

1.84DIA.

46.7

E-CoilView

TORQUE5–7 ft-lbs

(6.8–9.5 Nm)

TORQUE33–37 ft-lbs

(44.8–50.2 Nm)

1.0025.4

2.9374.4

2.3259.0

0.8722.1

1.4837.6

D-Coil View

U.S. Patent 7,921,880

SVCL10-30__ - __ __ __ - __ - __ __ __ __ __

Porting

Cartridge Only 0


Voltage 0 Less Coil** 12 12 VDC 20 20 VDC† 24 24 VDC**Includes D-Coil Nut




RP



SVRV10-26 Spool, 2-Way, Normally Open,

DESCRIPTIONA solenoid-operated, 2-way, spool-type, normally open, screw-in, hydraulic reliefvalve.

OPERATIONWhen the coil is de-energized, the valve is open, allowing flow from ➀ to ➁.When the coil is energized, flow from ➀ to ➁ is blocked. When the coil is energizedand the pressure at ➀ exceeds the relief setting, the valve will open to allow flow from➀ to ➁.

FEATURES• Various pressure ranges.• Continuous-duty rated solenoid.• Hardened spool and cage for long life.• Optional coil voltages and terminations.• Efficient wet-armature construction.• Cartridges are voltage interchangeable.• Optional waterproof E-Coils rated up to IP69K.• Unitized, molded coil design.• Industry common cavity.

RATINGSOperating Pressure: 275.8 bar (4000 psi)Flow: 0 to 56.8 lpm (0 to 15 gpm)Relief Pressure Settings – defined as pressure evident at 7.57 lpm (2 gpm):

A: 240 ±13 bar (3500 ±190 psi)B: 207 ±12.5 bar (3000 ±180 psi)C: 172 ±11.5 bar (2500 ±165 psi)D: 138 ±10.5 bar (2000 ±150 psi)E: 104 ±9.5 bar (1500 ±135 psi)For custom OEM settings, consult factory.

Reseat Pressure: 90% of relief pressure settingPilot Flow & Leakage at 85% of relief pressure setting: 86 ml (2.9 oz.) per minutePressure Rise at Max. Current (Relief Mode): 0.566 ±0.018 bar/lpm

(31.0 ±2.0 psi/gpm)Temperature: -40 to 120°C with standard Buna sealsCoil Duty Rating: Continuous from 85% to 115% of nominal voltageInitial Coil Current Draw at 20°C: Standard Coil: 1.67 amps at 12 VDC; 0.18 amps


7.4 to 420 cSt (50 to 2000 ssu)Installation: No restrictions; See page 9.020.1Cavity: VC10-2; See page 9.110.1Cavity Tool: CT10-2XX; See page 8.600.1Seal Kit: SK10-2N-B; See page 8.650.1Coil Nut: Part No. 7004420

USASI/ISO:


SYMBOLS

1.720.1

2.8/40

2.4/35

2.1/30

1.7/25

1.4/20

1.0/15

0.7/10

0.3/5

11.43

22.76

34.19

56.815

FLOW lpm/gpm

PR

ES

SU

RE

DR

OP

bar

/psi

45.412

No Current; Coil De-energized32 cSt/150 sus oil at 40°C

207/3000

241/3500

276/4000

138/2000

172/2500

69/1000

103/1500

11.43

A

B

C

D

E

22.76

34.19

56.815

FLOW lpm/gpm

PR

ES

SU

RE

DR

OP

bar

/psi

45.412

Coil Energized32 cSt/150 sus oil at 40°C

SOLENOID VALVES

Expanded:

DESCRIPTIONA solenoid-operated, normally-closed, on/off, poppet-type, screw-in hydraulic cartridge valve incorporating an integral load-sense pressure port with isolation check.

OPERATIONWhen de-energized, the SVCL10-32 blocks flow at ports 3 and 1. When energized, flow is allowed from 3 to 1 and 2 with a check-isolated load sense signal supplied at 2. Reverse flow is not allowed from 1 to 3.

NOTE: When using this valve in bridge circuits, seals should not be used on the pilot pistons of the pilot-operated check valves. This is to avoid trapping oil which would keep the pilot-operated check valve open.

FEATURES• Continuous-duty rated solenoid.• Hardened precision spool and cage for long life.• Optional coil voltages and terminations.• Efficient wet-armature construction.• All ports may be fully pressurized.• Cartridges are voltage interchangeable.• Optional waterproof E-Coils rated up to IP69K.• Unitized, molded coil design.• Reduce manifold space claim.

RATINGSOperating Pressure: 250 bar (3625 psi); Holding Pressure at 1: 250 bar (5000 psi)Flow: 15 gpm (57 lpm); see performance chartsInternal Leakage: Ports 1 and 3: 5 drops/minute max. at 250 bar (3625 psi)

Port 2: 10 drops/minute max. at 250 bar (3625 psi)Operating Temperature: -40° to 100°C (-40° to 212° F) with standard Buna N seals;

-26° to 204°C (-15° to 400°F) with Fluorocarbon seals;-54°C to 104°C (-65°F to 225°F) with Polyurethane seals

Coil Duty Rating: Continuous from 85% to 115% of nominal voltageInitial Coil Current Draw at 20°C: Standard D-Coil: 1.67 amps at 12 VDC;



7.4 to 420 cSt (50 to 2000 sus); See Temperature and Oil Viscosity, page 9.060.1Installation: No restrictions; See page 9.020.1Cavity: VC10-3, Variation “B”; See page 9.110.1Cavity Tool: CT10-3XX; See page 8.600.1Seal Kit: SK10-3X-MM; See page 8.650.1Coil Nut: Part No. 7004400

SVCL10-32 Poppet, 3-Port, Normally Closed

SYMBOL

1.315.1


SOLENOID VALVES

HYDRAFORCE.com®

ISO:

Expanded:

3 to 132 cSt/150 sus oil at 40°C

17.2/250

13.7/200

10.3/150

6.9/100

3.4/50

22.76

45.412

56.815

FLOW lpm/gpm

PR

ES

SU

RE

DR

OP

bar

/psi

11.43

34.19

3 to 2 1.2A32 cSt/150 sus oil at 40°C

1.03/15

0.83/12

0.62/9

0.41/6

0.21/3

0.760.2

1.520.4

1.900.5

FLOW lpm/gpm

PR

ES

SU

RE

DR

OP

bar

/psi

0.380.1

1.140.3

U.S. Patent 7,921,880

RP



DIMENSIONS

SVCL10-32

1.315.2

TO ORDER

Cartridge: Weight: 0.18 kg. (0.40 lbs.); Steel with hardened work surfaces. Zinc-plated exposed surfaces. Buna N O-rings and polyester elastomer back-up standard.

Standard D-Coil: Weight: 0.27 kg. (0.60 lbs.); Unitized thermoplas-tic encapsulated, Class H high temperature magnetwire. See page 3.200.1.

E-Coil: Weight: 0.41 kg. (0.9 lbs.); Fully encapsulated with rugged external metal shell. Rated up to IP69K with integral connectors. Note: See page 3.400.1 for all E-Coil retrofit applications.

MATERIALS

®HYDRAFORCE

HYDRAFORCE.com®

1.6241.1

1.84DIA.

46.7

E-CoilView

TORQUE5–7 ft-lbs

(6.8–9.5 Nm)

TORQUE33–37 ft-lbs

(44.8–50.2 Nm)

1.0025.4

2.9374.4

2.3259.0

0.8722.1

1.4837.6

D-Coil View

U.S. Patent 7,921,880

SVCL10-32__ - __ __ __ - __ - __ __ __ __ __

Porting

Cartridge Only 0


Voltage 0 Less Coil** 12 12 VDC 20 20 VDC† 24 24 VDC**Includes D-Coil Nut




RP



SVRV10-26

DIMENSIONS

1.720.2

HYDRAFORCE®

PressureSettings

240 ±13 bar(3500 ±190 psi) A

207 ±12.5 bar(3000 ±180 psi) B

172 ±11.5 bar(2500 ±165 psi) C

138 ±10.5 bar(2000 ±150 psi) D

104 ±9.5 bar(1500 ±135 psi) E

MATERIALS TO ORDER





SVRV10-26__ - __ __ __ - __ - __ __ __ __ __


SAE 6 6TSAE 8 8T













VoltageStd. Coil


12 12 VDC 24 24 VDC 36 36 VDC 48 48 VDC 24 24 VAC115 115 VAC230 230 VAC**Includes Std. Coil Nut.† DS, DW or DL

terminations only


1.6241.1

1.84DIA.

46.7

E-CoilView

StandardCoil View

2.8572.4

with Internal Relief

For custom OEMsettings, consult factory.


SVRV12-26F Spool, 2-Way, Normally Open,

DESCRIPTIONA solenoid-operated, two-way, spool-type, normally open, screw-in, hydraulic pressure-relief valve.

OPERATIONWhen the coil is de-energized, the SVRV12-26F is open, allowing fl ow from ➀ to ➁. When the coil is energized, fl ow from ➀ to ➁ is blocked. When the coil is energized and the pressure at ➀ exceeds the relief setting, the valve will open to allow fl ow from ➀ to ➁.

FEATURES• Continuous-duty rated solenoid.• Hardened spool and cage for long life.• Effi cient wet-armature construction.• Cartridges are voltage interchangeable.• Optional waterproof E-Coils rated up to IP69K.• Unitized, molded coil design.• Industry common cavity.

RATINGSOperating Pressure: 297 bar (4300 psi)Flow: 0 to 189 lpm (0 to 50 gpm)Relief Pressure Range – setting defi ned as pressure evident at 7.57 lpm (2 gpm):

20.7 to 296.5 bar (300 to 4300 psi)Reseat Pressure: 80% of relief pressure settingPilot Flow & Leakage at 80% of relief pressure setting: 350 ml per minute max.Temperature: -40 to 100°C with standard Buna seals

-26 to 204°C with Fluorocarbon sealsCoil Duty Rating: Continuous from 85% to 115% of nominal voltagePull-In Amps: 1.14 amps maximumMinimum Pull-in Voltage: 85% of nominal at 207 bar (3000 psi)Drop-Out Amps: 0.08 amps minimum – defi ned as relief pressure returning to

pressure drop across valveFiltration: See page 9.010.1Fluids: Mineral-based or synthetics with lubricating properties at viscosities of

7.4 to 420 cSt (50 to 2000 sus); See Temperature and Oil Viscosity, page 9.060.1Installation: No restrictions; See page 9.020.1Cavity: VC12-2; See page 9.112.1Cavity Tool: CT12-2XX; See page 8.600.1Seal Kit: SK12-2X-B; See page 8.650.1Coil Nut: Part No. 7004420

USASI/ISO:


SYMBOLS

1.722.1

Expanded:

SOLENOID VALVES

HYDRAFORCE.com®

10.3/150

9.3/135

8.3/120

7.2/105

6.2/90

5.2/75

4.1/60

3.1/4537.910

75.720

113.630

189.350

FLOW lpm/gpm

PR

ES

SU

RE

DR

OP

bar

/psi

151.440

Pressure vs. Flow; Coil De-Energized32 cSt/150 sus oil at 40°C

207/3000

276/4000

345/5000

138/2000

69/1000

03810

7620

11330

18950

FLOW lpm/gpm

PR

ES

SU

RE

DR

OP

bar

/psi

15140

Pressure vs. Flow; Coil Energized32 cSt/150 sus oil at 40°C

207/3000

276/4000

138/2000

69/1000

0 0.05 0.10 0 0.05 0.10

TIME seconds

PR

ES

SU

RE

bar

/psi

Response to Inlet PressureSupporting Valve Upstream

Flow 7.6 lpm/2 gpmStep Up Step Down

U.S. Patent 7,137,406

RP



SVRV12-26F

DIMENSIONS

1.722.2

MATERIALS TO ORDER

Cartridge: Weight: 0.25 kg. (0.56 lbs.) Steel with hardened work surfaces. Zinc-plated exposed surfaces. Buna N O-rings and polyester elastomer back-up standard.

Standard Ported Body: Weight: 0.57 kg. (1.25 lbs.) Anodized high-strength 6061 T6 aluminum alloy, rated to 207 bar (3000 psi). Ductile iron bodies available; dimensions may differ. See page 8.012.1

Standard Coil: Weight: 0.27 kg. (0.60 lbs.) Unitized thermoplastic encapsulated, Class H high temperature magnetwire. See page 3.200.1

E-Coil: Weight: 0.41 kg. (0.9 lbs.); Fully encapsulated with rugged external metal shell. Rated up to IP69K with integral connectors. Note: See page 3.400.1 for all E-Coil retrofi t applications.

SVRV12-26F - __ __ __ - __ - __ __ __ __ __ / __ __ __ __



**Includes Std. Coil Nut.

Voltage Std. or E-Coil 0 Less Coil** 12 12 VDC 24 24 VDC

with Internal Relief

®HYDRAFORCE

HYDRAFORCE.com®

1.6241.1

1.84 (46.7) DIA.

TORQUE:4 – 5 ft-lbs(5.4 – 6.8 Nm)

TORQUE:33 – 37 ft-lbs

(44.7 – 50.2 Nm)

E-CoilView

StandardCoil View

Setting in bar 21 to 297 bar Examples: M75 75 bar M190 190 bar Setting in psi 300 to 4300 psi Examples: 6.0 600 psi 30.0 3000 psi

U.S. Patent 7,137,406

For Coil with Zener Diode, add “/Z” to option code. For example: “ER/Z”. Not available on all models. See coil option info. on pages 3.200.1 & 3.400.1

Coil Termination E-Coil D-CoilDeutsch DT04-2P ER (IP69K) DR (IP65)Metri-Pak 150 EY (IP69K) DY (IP65)Dual Lead Wires EL (IP69K) DL (IP65)Amp Jr. Timer EJ (IP67) —DIN 43650 EG (IP65) DG (IP65)Dual Spades — DS (IP65)

For other voltages, see pages 3.200.1 & 3.400.1

Porting Cartridge Only 0 Alum. Body SAE 10 10T SAE 12 12T SAE 16 16T 1/2 in. BSP* 4B 3/4 in. BSP* 6B 1 in. BSP* 8B Duct. Iron Body SAE 10 10TD SAE 12 12TD SAE 16 16TD 1/2 in. BSP* 4BD 3/4 in. BSP* 6BD 1 in. BSP* 8BD

RP



Documents

YDRAFORCE Solenoid Valves - Altan · PDF fileManual Override “M” Option for Three-Position Push/Pull-Type Solenoid Valves Note: This option is not available along with the Waterproofing