36
Intro to CTI Dear ZOT Customer Welcome to ZOT’s Catalog of unique electronic and mechanical parts and assemblies for AMF equipped bowling centers. This years catalog features a section for ZOT’s line of Ball Conditioner Products that include the GlossBoss and GlossBoss II Ball Conditioners, and a line of Restoration and Conversion Kits for most existing brands of ball-conditioning machines, including the Lustre King, Lustre Kleen and the AMF/Century Ball Performance Center. You will also find a full-line of CTI by ZOT control systems and related electronic products for AMF 82-70 & 82-30 Pinspotters. Thank you as always for your business and we look forward to serving your needs in the future. Roger Lindblad President–ZOT Pinsetter Parts Inc. Table of Contents Section 1 CTI by ZOT 82-90 Pages 1 82-70 Page 2-9 82-30 Pages 9-11 Section 2 Glow Bowling Products Pages 12-15 Section 3 Unique Parts Pages 15-19 Section 4 Foul Detectors Pages 20-25 Section 5 Electronic Triggering Pages 25-27 Section 6 Lane Products Pages 28-29 Section 7 Ball Conditioner Products Pages 30-36 Pit Power Manager For AMF 82-70 MP Chassis, 5-Board and Converted Chassis #400253 ......... Pricing Upon Product Release Saves Wear & Tear to machine parts: the ZOT Pit Power manager turns off the back-end motor when the pinspotter has been sitting idle [e.g., the timing is adjustable using the DIP switch from 3 – 6 minutes]. Reduced Pin Damage: The Power manager will turn off the back-end motor when there’s a pin jam in the distributor area. 2-lane Controller: the Pit Power Manager mounts on the rear of the mechanics Control Box between two-lanes. Mechanics Alert Indication: a Red LED signals when the back-end motor has turned off by the manager, in the case of a pin-jam, or when the machine has been idle for the preset number of minutes. LED’s are located at the front and rear of the Pit Power Manager unit. Self Restart: When the machine has been sitting idle the back-end motor will turn on automatically when a ball contacts the pit cushion. On/Off Switch: Will set to continuous run for maintenance. Additional Savings on your monthly electric bill. NEW

Zot Amf Catalog

Embed Size (px)

Citation preview

Intro to CTI

Dear ZOT Customer

Welcome to ZOT’s Catalog of unique electronic and mechanical parts and assemblies for AMF equipped bowling centers.

This years catalog features a section for ZOT’s line of Ball Conditioner Products that include the GlossBoss and GlossBoss II BallConditioners, and a line of Restoration and Conversion Kits for most existing brands of ball-conditioning machines, including theLustre King, Lustre Kleen and the AMF/Century Ball Performance Center.

You will also find a full-line of CTI by ZOT control systems and related electronic products for AMF 82-70 & 82-30 Pinspotters.

Thank you as always for your business and we look forward to serving your needs in the future.

Roger LindbladPresident–ZOT Pinsetter Parts Inc.

Table of ContentsSection 1

CTI by ZOT82-90 Pages 1

82-70 Page 2-982-30 Pages 9-11

Section 2Glow Bowling Products

Pages 12-15

Section 3Unique Parts

Pages 15-19

Section 4Foul Detectors

Pages 20-25

Section 5Electronic TriggeringPages 25-27

Section 6Lane ProductsPages 28-29

Section 7Ball Conditioner ProductsPages 30-36

Pit Power ManagerFor AMF 82-70 MP Chassis, 5-Board and Converted Chassis

#400253.........Pricing Upon Product ReleaseSaves Wear & Tear to machine parts: the ZOT Pit Power manager turns off the back-end motor when the pinspotter has been sitting idle [e.g., the timing is adjustable using the DIP switch from 3 – 6 minutes].

Reduced Pin Damage: The Power manager will turn off the back-end motor whenthere’s a pin jam in the distributor area.

2-lane Controller: the Pit Power Manager mounts on the rear of the mechanicsControl Box between two-lanes.

Mechanics Alert Indication: a Red LED signals when the back-end motor has turnedoff by the manager, in the case of a pin-jam, or when the machine has been idlefor the preset number of minutes. LED’s are located at the front and rear of the PitPower Manager unit.

Self Restart: When the machine has been sitting idle the back-end motor will turnon automatically when a ball contacts the pit cushion.

On/Off Switch: Will set to continuous run for maintenance.

Additional Savings on your monthly electric bill.

NEW

1

82-90 Pinspotter Products

1

CTI

by

ZOT

CXL Dual Lane Controller Chassis#829001 (115V/60Hz)#829002 (230V/50Hz)An enhanced direct replacement for AMF 82-90XL &8800 Gold Dual Lane Chassis

The ZOT CXL Chassis has all the fea-tures of an AMF 82-90 XL Chassis, plusthe following:

• The fuses in the ZOT Chassis give you additional protection to the fuses in the Pinspotter cabling.

Note: There are no fuses on an AMF 82-90 XL Chassis

• Mechanics option switches for: a) Sweep Reverse on Offspotb) Foul on – Foul offc) Ninepin No Tap

• Sweep and Table Motor Disable pushbuttons

• Continuous cycle LED’s

Easy Lane SelectionSweep and TableDisable

Mechanics Option

Fuses

Front End Dual Lane Control Box#829004An enhanced replacement for an AMF 82-90 Front-EndControl Box.

The ZOT Front End Dual-Lane Control Box:• Can eliminate the MCU with other brands (non AMF) of

scoring systems.• Can eliminate the need for the AMF Source Command

interface.

Fat Chassis Conversion Kit#829100 (115V/60Hz) ............Price by Quotation#829200 (230V/50Hz) ............Price by QuotationAn upgrade for AMF 82-90 Pinspotters with Fat Chassis

Kit Includes:One CXL Dual Lane ChassisOne Front End Dual Lane Control Box

Kit containing set of 14 each Conversion cables:#829003

Features and Benefits

Microprocessor Efficient: State-of-the-Art Technology simplifies the circuitReduced Power Consumption: Modern PC-Board components require less powerReset/Program Zero: Enables zeroing the memory of the chassisScoring Interface: Compatible with all Major brands of scoringShort Cycle Capable: Allows for some Automatic Scoring units to communicate on a strike that the table does not go down to feel for pinsPindication Capable: Has the circuitry necessary to drive the pin-lights for the masking units that have a pindication featureEase of Installation: All connections made with quick disconnect terminals

Option Jumper’sInstruct: Enables the Mechanic to override the front desk control switches. The machine cycles irrespective of whether theswitches are in the Instruct-O-Mat or Bowl positionsFoul: Enables disabling of the foul communication to the machine: without disabling the foul light at the approach

2

1

CTI b

y ZOT

82-70 Pinspotter Products

5 to 1 Board Conversion#827001with Pindication Diagnostics (includes #827006)

Enhanced single board conversion for OriginalAMF 5-board ChassisSame features as the AMF XOP/98-70 board

Master Controller Interface Port (see page 6)

Note:Master Controller interface compatible.

Optional Add-on Short Run Cycle -Communications Cable#827006Adding the CTI by ZOT Sweep Reverse Communications Cable to the5 to 1 board Conversion will provide all automatic scoring features,including: Short Strike Cycle, Short Cycle 7 to 10-pin Pick, or ShortCycle Miss (Gutter ball) and automatic sweep reverse on offspot.

Compatible with all brands of automatic scoring, includingBrunswick Vector, but not including FrameWorx, AS90, AS80, ASKand all other Brunswick systems.

Now Includes#827006 Cable

Features and BenefitsMicroprocessor Efficient: State-of-the-Art Technology simplifies the circuitReduced Power Consumption: Modern PC-Board components require less powerReset/Program Zero: Enables zeroing the memory of the chassis. Also serves as a manual intervention (a safety feature formechanics) if the Chassis is shut down. This button “Must be Depressed” to restart the machineScoring Interface: Compatible with all Major brands of scoringShort Cycle Capable: Allows for some Automatic Scoring units to communicate on a strike that the table does not go down tofeel for pinsPindication Capable: Has the circuitry necessary to drive the pin-lights for masking units that have this featureEase of Installation: All connections made with quick disconnect terminals

Option Jumper’sInstruct: Enables the Mechanic to override the front desk control switches. The machine cycles irrespective of whether theswitches are in the Instruct-O-Mat or Bowl positionsBack-End: Enables the mechanic to select whether the back-end motor shuts off if there’s no bowling activity for (3) minutes: orrun continuously as long as the machine is turned onFoul: Enables disabling of the foul communication to the machine: without disabling the foul light at the approachMaster Controller interface compatible

Diagnostic LED’s1st – Ball – 2nd: Indicates whether the machine is on First or Second ballFoul: Lights when a foul signal has been generatedSweep: Lights when button is depressed while operating sweepTable: Lights when button is depressed while operating table10 Pin Lights: Light when re-spot cells switches are activatedStrike: Lights when a bowler knocks down all pins on first ball

3

1

CTI

by

ZOT

82-70 Pinspotter Products

MP PC Control Board#827002with Pindication Diagnostics

Enhanced replacement for AMF 98-50 single boardSame features as AMF 98-60 board

MasterController Interface Port (see page 6)

Provides all operational features of the original equipment, plus:

Features and Benefits Diagnostic LED’sCycle: Lights when button is depressed. The light also stays onwhen machine is in continuous cycle1st – Ball – 2nd: Indicates whether the machine is on First orSecond ballS/R: Lights when button is depressed while operating a Sweep ReverseSweep: Lights when button is depressed while operating a SweepTable: Lights when button is depressed while operating the TableOption Set: Lights when button is depressed while program-ming Special Options10 Pin Light: Light when re-spot cell switches are activatedInstruct: Lights when machine is in Instruct-O-Mat modeCycle Speed: Lights depending on the programming of thechassis (normal, medium, and fast)Status: Lights depending on which micro-switches are activated (e.g., Grippers, Bin, etc.)Options: Lights depending on the programming of the Chassis(e.g., 1ST Ball only, 3rd Ball, or 8/9 no tap)

Push Button Function ControlsOption Set: Enables the Mechanic to program the SpecialFunctions of the Chassis1st – Ball – 2nd: Enables the Mechanic to toggle the machinebetween 1st and 2nd ballCycle: Enables the Mechanic to cycle the machine from theChassis and operate a Continuous Cycle

Programmable Options for "Special Promotions"AS – 1st Ball Only: The machine always sets a full deck of pinsand stays on 1st ball — with or without automatic scoringAS – 3rd Ball: The machine adds an extra (e.g., 3rd) ball for eachbowler to the same deck of pins — with or without automaticscoring8/9 – Pin Strike: The machine operates in a No-tap mode,regardless of whether the center has automatic scoring. If thebowler gets 8 or 9 pins on the first ball, the machine will run astrike cycle

Replacement Breakers#220040 12-AMP#220039 10-AMP#220016 2-AMP#220038 1-AMP

4

1

CTI b

y ZOT

82-70 Pinspotter Products

Note: When replacing an original 5-board chassis with an Ultra Air or Ultra Air Plus, installation requires a mask adapter cable (ELCO).See page 8.

Ultra Air PlusProgrammable Pinspotter Controller Chassis#827015(115V60Hz) Rear Facing UnitAn Enhanced Direct Replacement Chassis for AMF 82-70 PinspottersThe “New” Generation

The Ultra Air Plus has all the features and benefits of the Ultra Air (see page 5) and the following:

Rear FacingControl versionshown

Improved

5

1

CTI

by

ZOT

82-70 Pinspotter Products

Note: For optimum control, ease of troubleshooting, safety and convenience for the mechanic, from both the front and back ofthe Pinspotter, ZOT recommends combining a Front Facing Chassis with the Rear Mounted Master Controller (see page 6).When replacing an original 5-board chassis with an Ultra Air or Ultra Air Plus, installation requires a mask adapter cable (ELCO). See page 8.

Ultra AirPinspotter Controller Chassis#827003 (115V60Hz) Rear Facing unit #827004 (115V60Hz) Front Facing unit#827023 (230V50Hz) Rear Facing unit #827024 (230V50Hz) Front Facing unitEnhanced replacement Chassis for AMF 82-70 Pinspotters

Front FacingControl version

shown

Ultra 99#827029(230/50Hz) Front Facing unitDirect replacement for VANTECH VPS 2000

Replacement Breakers#220040 12-AMP

#220039 10-AMP

#220016 2-AMP

#220038 1-AMP

Push Button Function ControlsSweep: Enables running the sweep from the ChassisS/R (Sweep Reverse): Enables running the Sweep Reversefrom the ChassisTable: Enables running the Table from the ChassisReset/Program Zero: Enables zeroing the memory of theChassis. Also serves as a manual intervention (a safety fea-ture for mechanics) if the Chassis is shut down. This button“Must be Depressed” to restart machineCycle: Enables cycling the machine from the Chassis

Resetable BreakersMain Power Circuit Breaker: Shuts down power to themachineTable Motor: Protects Chassis if motor overloadsSweep Motor: Protects Chassis if motor overloadsBack-End Motor: Protects Chassis if motor overloadsSpot Solenoid & Pit Light: Protects Chassis if a short occursAC Transformer: Protects Chassis if a short occurs

Diagnostic LED’sPower: Indicates when the chassis has powerHigh Voltage Fault: Indicates when there is a short in the 115VoltcircuitLow Voltage Fault: Indicates when there is a short in the 24VoltcircuitOption Switch’sService: Enables the Mechanic to turn the machine on fromthe Chassis: overriding the front desk control switchesInstruct: Enables the Mechanic to override the front deskswitches. The machine cycles irrespective of whether theswitches are in the Instruct-O-Mat or Bowl positionsOff Spot: Enables the mechanic to select whether the machine willperform an automatic sweep reverse in the case of an off spotFoul: Enables disabling of the foul communication to themachine: without disabling the foul light at the approachBack-End: Enables the mechanic to select whether the back-endmotor shuts off if there’s no bowling activity for five (5) minutes: or run continuously as long as machine turned on

The “New” GenerationZOT has reengineered and designed selected components in the Ultra 98 and is pleased to introducethe Ultra Air, a much more user friendly and reliable pinspotter controller for your AMF 82-70’s.

Check these “all new” added Features and Benefits:

Circuit Protection: The original Slow-Blow fuse protection has been replaced with four“Resettable” Breakers, all set at lower amperages than the original fuses, for added protec-tion. If a Breaker trips, simply reset the Breaker after eliminating the cause of the overload.

Air Cooling System: The internal components of the chassis will be air cooled by a fanmounted in the side panel of the unit. Just like a computer, the fan runs at all times whenpower is applied to the Pinspotter, e.g., form the Managers Control.

Heavier Traces on the Driver Board: By Increasing the traces from 2oz. to 4oz. on the driver board ZOT has improved the amount of current the board can withstand before burning traces.

Gold Sockets and Pins: Have been added to the C1 and C2 plug connectors for improved contact and reduced burning.

Improved

Features and Benefits Pinspotter Control ButtonsEnables the mechanic to manage the following functions fromthe rear of the pinspotterSweep: Enables running the sweep from the ControllerS/R (Sweep Reverse): Enables running the Sweep Reversefrom the ControllerTable: Enables running the Table from the ControllerReset/Program Zero: Enables zeroing the memory of theChassis. Also serves as a manual intervention (a safety featurefor mechanics) if the Chassis is shut down. This button "Mustbe Depressed" to restart machine1st – Ball – 2nd: Enables the Mechanic to toggle the machinebetween 1st and 2nd ballCycle: Enables the Mechanic to cycle the machine from theController and operate a Continuous Cycle

Diagnostic LED’sThe Master Controller features 26 Informational andDiagnostic LED Indicators for each lane, including the follow-ing: Power, Cycle, 1st – Ball – 2nd, S/R, Sweep, Table, 10 PinLights, Instruct, Continuous Cycle, OS, GP, BIN, SRG, SA, SB, TA1& TA2.

Option SwitchesService: Enables the Mechanic to turn the machine on fromthe Controller: overriding the front desk control switchesInstruct: Enables the Mechanic to override the front deskswitches. The machine cycles irrespective of whether theswitches are in the Instruct-O-Mat or Bowl positionsOff Spot: Enables the mechanic to select whether the machinewill perform an automatic sweep reverse in the case of an offspotFoul: Enables disabling of the foul communication to themachine: without disabling the foul light at the approachBack-End: Enables the mechanic to select whether the back-end motor shuts off if there’s no bowling activity for five (5)minutes: or run continuously as long as machine turned on

6

1

CTI b

y ZOT

82-70 Pinspotter Products

Master Controllerfor AMF 82-70 Pinspotters #827005

Controls two AMF 82-70 Pinspotters

Note:Requires CTI by ZOT MP PC Board, 5 to 1 Board Conversion or any CTI Ultra 98 or Ultra Air Chassis to operate.

• The CTI by ZOT MasterController providesmechanics with AMF 82-70Pinspotters with diagnosticsthat are superior to AMF82-90 Pinspotters. It’s theclosest thing possible to an82-90XL field conversion …and it costs a lot less.

• The CTI by ZOT MasterController provides infor-mation and controls thatenable the mechanic toefficiently troubleshoot,repair and control AMF 82-70 Pinspotters withoutmoving the chassis fromlane to lane.

• Mechanics enjoy easy accessto the Master Controller,which interfaces with twolanes, and mounts abovethe two ‘Back-End’ controlboxes on the rear of themachine.

• Installation is easy too: Yousimply drill two holes, boltthe unit in place, and con-nect the Master Controllerto the CTI Chassis and/orCTI PC Board by plugging intwo telephone style cables.

Q.Do you know which respot cell is giving you a problem?

A.The Master Controller will tell you!

Also Available:99 Master Controller#827030Direct replacement for VANTECH Rear Control Center

Great Diagnostic ToolFor Ultra Air, Ultra 98,Current AMF 5 BoardWith Phone Jack

7

1

CTI

by

ZOT

82-70 Pinspotter Products

A “Superior” alternative to Solid State products offered by other manufacturers

Electronic Motor Start AssemblyFor AMF 82-70 Pinspotter Motors

#300058ZOT’s Electronic Motor Start Assembly is a directreplacement for centrifugal motor start switches andvarious brands and models of Solid State motorstarters.

Check these features:Retains the same dynamic breaking circuit as the centrifugal start mechanism it’s replacing.Reduces motor coasting or creep associated with OEM and various brands of Solid State motor startersDurable: the ZOT Electronic Motor Start Assembly has a far greater life expectancy than Solid State alternatives.Senses changes in Voltage: The ZOT product senseschanges in voltage in the motor start winding, and disconnects the capacitors at the correct voltage, with“no” fine tuning or intricate adjustments required.Easy to Install: The assembly mounts in the existingwire channel and uses simple disconnects, with noneed to remove the centrifugal mechanism it’s replacing.

Gorilla Grip Distributor BeltFor 82-70 & 82-90 Pinspotters# 800130 (124” Long)

For 82-30 Pinspotters# 800133 (165” Long)

(Above part numbers include Belt Lace and Pin)

The best pin grip in the industry: proven by extensive testing in bowling centersFewer pin jams: The belt is designed and used inthe catering industry to move light food productsup an incline.Maintains pin grip: Oil and dirt settles in a tire-like tread to ensure the apex of the belt remainsclean and oil free.

Replacement Parts

# 800131 2 3/4” Belt lace for 82-70/90

# 800134 3 1/2” Belt lace for 82-30

# 800132 2 3/4” Belt Pin for 82-70/90

# 800135 3 1/2” Belt Pin for 82-30

8

1

CTI b

y ZOT

82-70 Pinspotter Products

Scoring/Mask ConnectorsReplace Worn & Unreliable ELCO Connectors with more cost effective AMP Connectors as found on MP Chassis

Improve Chassis reliability by restoring Scoring and Mask connection communication to like-new condition

Easy to Re-pin: It’s easier to Re-pin your chassis than you think … easy to follow instructions are included.

Chassis Receptacle#230197(37 connectors) C23 Mask & APS (Scoring)

Keying Pin#230122for C23 Mask & APS (Scoring)

Cable Plug#230119(37 connectors) C23 Mask & APS (Scoring)

Cable Clamp#230120(37 connectors) C23 Mask & APS (Scoring)

Conversion Kits#827C23C23 Plug Connector Kitfor Mask & APS (scoring)Used to convert existing cables to theC23 connector matching the connectionon an Ultra98/Ultra Air and/or Ultra 98Plus/Ultra Air Plus.

#827C17C17 Plug Connector KitFor converting existing cables to theC17 Connector matching the connectionon an Ultra 98 Plus or Ultra Air PlusNote: An AMP Crimping Tool may berequired for Proper installation of thesetwo kits.

Cable Assemblies#827M23Cable Assembly – Mask UnitConnector Kit to communicate signals fromthe Mask Unit to the Pinspotter Chassis

#827S23Cable Assembly – ScoringTo communicate signals from AutomaticScoring to the Pinspotter Chassis

#827P17Cable Assembly – Ultra 98Plus/Ultra Air Plus AccessoryOnly interfaces with an Ultra 98Plus/Ultra Air Plus Chassis to switch aux-iliary features on and off: e.g. bumpersystems and service lights.

ELCO Mask Adaptor Cable Assembly# 827007

Adaptor required for Quick Change from 5-Board Chassis to a NewZOT Solid State ChassisThis adaptor cable assembly is designed to convert (and is required to change)the original ELCO connection from a 5-Board Chassis to a C-23 Plug for anUltra 98/Ultra Air and/or Ultra 98 Plus/Ultra Air Plus application. This appliesirregardless if whether the original 5-Board Chassis has been converted.Another alternative is to order # 827M23 or # 827C23

9

Heavy Duty Locking Chassis Handle#823006For 82-30 chassisReplacing old or broken Chassis Handles with ZOT’s Superior Design ensures proper connectionsbetween the Chassis and the J-Strip. ZOT’s Heavy Duty Chassis Handles are a direct replacement for all handles.

1

CTI

by

ZOT

82-70/82-30 Pinspotter Products

Gold Socket .062 (female)#230121for Single Wire crimp#230143for Double Wire crimp

ConnectorsNote: Connection Maintenance is essential — up to 50% of all electronic pinspotter malfunctions are connector related

Gold Plated Connections for a Superior ConnectionFor better performance, use Gold in place of silver plated Pins and Sockets

Gold Socket .062 (male)#230141for Single Wire crimp#230142for Double Wire crimp

Chassis ReceptacleC1 Block (34 Connectors)

#230144

Cable PlugC1 Block (34 Connectors)

#230249

Replace cracked or broken blocks that no longer hold pins securely

Strain ReliefC1 Clamp

#230250

Strain ReliefC2A Clamp

#230252

Secure Cables to prevent wires from fraying

Chassis ReceptacleC2A Block (50 Connectors)

#230145

Cable PlugC2A Block (50 Connectors)

#230251

If you have pins or sockets that are pushed back, orblocks that are broken, replace them greater reliability

Guide Socket (female)for C1 & C2A#230195

Guide Pin (male)for C1 & C2A#230194

Locking Spring Clampfor C1 & C2A#230248

Extract ToolEasy removal tool for all .062DIA sockets & pins#860018

10

Features and Benefits Microprocessor Efficient: State-of-the-Art Technology simplifies the circuitScoring Interface: Compatible with all Major brands of scoringShort Cycle Capable: Allows for the Automatic Scoring to communicate on a strike that the tabledoes not go down to feel for pinsPower LED: Indicates when the “Smart Board” has powerEase of Installation: All connections made with quick disconnect terminalsOption Switch’sCycle: Allows the pinspotter to be cycled from the managers control when going from Instruct-O-Mat to BowlInstruct: Disables managers control for Instruct-O-Mat by keeping power off the machineFoul: Enables disabling of the foul communication to the machine: without disabling the foullight at the approach

Features and Benefits Memory Back-Up: Keeps the Pin Count and/or Zero in case of power lossLED Indicators: Shows the Pin Count and Zero PositionsMicroprocessor Efficient: State-of-the-Art Technology simplifies thecircuitInfrared Technology: Sees all current pins, including colored and UV PinsCompatibility: Interfaces with all 82-30 ChassisReset Button: Sets the Eagle-Eye to Zero Pin CountEase of Installation: The Eagle-Eye unit mounts in existing Pin Counterbracket holes, plus two additional holes that must be drilled

1

CTI b

y ZOT

82-30 Pinspotter Products

• The Solid State – MP Controlled CTI by ZOT “Smart Board”for AMF 82-30 Pinspotter Chassis is a feature rich productthat restores and improves the performance and reliabilityof AMF 6525 & 5850 Chassis.

• This superior product is easy to install, but ZOT also offersthe option of returning your old chassis for factory installa-tion of the board and thorough diagnostics and restoration.Call ZOT for a quotation.

Smart Board for AMF 82-30 PinspotterChassis#823004An enhanced product to restore and improve original AMF 6525 & 5850 Chassis.The CTI by ZOT “Smart Board” not only replaces the Stepper Coils it also replaces all of the PR Relays and Timer Motor.

#823005An enhanced replacement for original mechanical pin counters.The Solid State – MP Controlled CTI by ZOT “Eagle-Eye”Infrared Pin Counter for AMF 82-30 Pinspotters is a high-technology designed product that offers benefits not avail-able in the original mechanical pin counters, or other brandsof electronic pin counters.

Added BenefitsNo More Miscounts: ZOT’s unique Eagle Eye Pin Counterwith Ambient Light Shade eliminates pin miscounts.Reduced Vibration for Longer Life: The mounting for theNEW Eagle Eye Pin Counter and Ambient Light Shadeassembly stabilizes the fixture to reduce vibration whichimproves performance and increases the life of the unit.

ZOTNew and Improved

Smart Board

Light ShadeOnly#400115

Eagle-Eye Infrared Pin Counter

11

Diagnostic LED’sPower: Indicates when the chassis has powerHigh Voltage Fault: Indicates when there is a short in the 115VoltcircuitLow Voltage Fault: Indicates when there is a short in the 24VoltcircuitCycle: Lights when machine is in continuous cycle1st – Ball – 2nd: Indicates whether the machine is on First orSecond ballSweep: Lights when button is depressed while operating a SweepTable: Lights when button is depressed while operating the TablePin: Lights when pin feed solenoid is energized to fill the tableL & K: Checks all the respot cell switchesFoul: Lights when the chassis receives a signal from the foul unitInstruct: Lights when machine is on Instruct-O-Mat modeOption Switch’sCycle: Allows the pinspotter to be cycled from the managers con-trol when going from Instruct-O-Mat to BowlInstruct: Disables managers control for Instruct-o-Mat by keepingpower off the machineFoul: Enables disabling of the foul communication to themachine: without disabling the foul light at the approach

Push Button Function ControlsSweep: Enables running the sweep from the ChassisTable: Enables running the Table from the ChassisReset / Program Zero: Enables zeroing the memory of the Chassis.Also serves as a manual intervention (a safety feature for mechan-ics) if the Chassis is shut down. This button “Must be Depressed”to restart machine1st – Ball – 2nd: Enables the Mechanic to toggle the machinebetween 1st and 2nd ball.Cycle: Enables the Mechanic to cycle the machine from the Chassisand operate a Continuous CyclePin: Enables the Mechanic to control the Pin feed solenoidL & K: Enables the Mechanic to perform a test of all the respot cellswitchesResetable BreakersMain Power Circuit Breaker: Shuts down power to the machineTable Motor: Protects Chassis if motor overloadsSweep Motor: Protects Chassis if motor overloadsBack-End Motor: Protects Chassis if motor overloadsSolenoid: Protects Chassis if a short occurs

82-30 Pinspotter Products

Solid State 82-30 MP Air Chassis#823001 (115V/60Hz) AMF #6525#823003 (115V/60Hz) AMF #5850

An Enhanced Direct Replacement Chassis for AMF 82-30 Pinspotters

The “New” Generation

ZOT has reengineered and designed selected components in the 82-30 MP Chassis and is pleased to introduce the MP Air, a much more user friendly and reliable pinspotter controller for your AMF 82-30’s.

Check these “all new” added Features andBenefits:Circuit Protection: The original Slow-Blow fuse protection has been replaced with four “Resettable” Breakers, all set at lower amperages than the original fuses, for added protection. If a Breaker trips, simply reset the Breaker after eliminating the cause of the overload.

Air Cooling System: The internal components of the chassis will be air cooled by a fan mounted in the side panel of the unit. Just like a computer, the fan runs at all times when power is applied to the Pinspotter, e.g., form the Managers Control.

Replacement Breakers#220040 12-AMP

#220039 10-AMP

1

CTI

by

ZOT

Improved

12

2

Glo

w B

ow

ling

Prod

ucts

Glow Bowling Products

“The promotion that changed an industry...its good today...and it’ll still be good tommorrow”

Some thoughts about Glow Bowling

Recreation centers – centers that havethe flexibility to provide an environ-ment for both entertainment andsport bowling – are centers that makethe most money and the highest prof-its for proprietors today.

And, there’s no better place to startintroducing Glow Bowling than at thepindeck…by adding ZOT GlowPindeck Light or GlowVision fixtures.Some proprietors have done it theother way around, added Glow light-ing to everything in theircenter…except the pindeck.

“Those proprietors have missed thepoint.” Whether we’re talking aboutSport or Recreation bowling, thegame’s about pins…and trying toknock them down. And, if the pinsdon’t “Glow” you’re really not in theGlow Bowling business.

Adding ZOT Glow Pindeck orGlowVision Lights is also the quickestand least expensive way to get startedin the Glow bowling business.Combine a Glow Pindeck with a goodpromotion plan, and your customersand your business will both profitfrom the Glow Bowling Experience.

Control up to 24-lanes with One Switch with ZOT’s Front Desk Switch ControlLogically the First Choice

When ZOT researched and developedits Glow Pindeck Light system it wasobvious that proprietors were look-ing for options that are the best fitfor their individual center needs. Forexample, switch control* options thatenable switching from white (sportbowling) to ultra-violet (recreationbowling) light from the front desk, orthe rear of the pinsetting machine.

Both are better options than otherbrands offered that has the switchcontrol on the fixture…whichrequires the mechanic to walk acrossthe lanes to access the switch…and,in full view of your customers. Formore details on ZOT GlowVision andTwo-Lamp Glow Pindeck light sys-tems contact your ZOT Distributor.

Take Control of Your Fixtures

Transformer & Switch Kit#400162

Two Conductor Wire#312003(Order by the foot)

ZOT Brand Relay Box Switch Controlincluded with Front Desk ControlledTwo-Lamp Pindeck Light fixture#400154

ZOT BrandSwitch &Bracketincluded inRear MountControlledTwo-LampPindeckLight fix-ture.

Note:Pindeck Lights are powered (turned on and off) by the Pinsetter.Pindeck Light Switch Controls change the lights from White to Black(Glow) and vice versa…they do not turn the Pindeck lights on or off.

Control Each Lane Individually with ZOT’s Switch Control on the Rearof the Pinsetting machine

13

Glow Bowling Products

When you order either of the abovepart numbers you will also require:

A. One length run of wire #312003 forup to 24-lanes to extend from Curtainwall to Front Desk (order by the foot).

B. One each #400162 Transformer &Switch Kit (serves up to 24-lanes).

All it takes is a flip of a switch to con-vert your center from a Sport toRecreation center…and it starts withZOT Two-Lamp Glow Pindeck Lights

ZOT Two-Lamp Glow Pindeck Light Fixture“An opportunity that’s too good to miss! ZOT’s Two-Lamp Glow Pindeck Light costs less than replacing an original AMF Dual Pindeck Lamp”

Front Desk Switching Option (See page 12 for control)#420336 (115V/60Hz)For all Domestic (US) applications, andsome overseas markets, as appropriate.

#420355 (230V/50Hz)For some overseas markets, as appropriate. This option enables switching fromWhite to Black Light on all lanes in uni-son from the Front Desk.

One lamp forSport Bowling

Note:For every two units you order of either ofthe above part numbers ZOT automaticallyincludes one Relay Box Switch Control and14’ of connecting wire for every two units.

Note:Order In Pairs

Transformer & Switch Kit(Order Separately)

Spring Loaded Lamp Socket

Rear of Pinsetter SwitchingOption (See page 12 for control)#420334 (115V/60Hz)For all Domestic (US) applications, andsome overseas markets, as appropriate.

#420340 (230V/50Hz)For some overseas markets, as appropriate.

This option enables easy switching fromWhite to Black light lane by lane from therear of the pinsetter. Each unit comescomplete with a Toggle Switch andmounting bracket.

One lamp forRecreation Bowling

Features and Benefits:

Welded Steel Construction: ZOT’s Two Lamp Glow Pindeck light fixtures are built with20-gauge steel and will withstand years of excessive vibration in the pindeck area.Spring Loaded Lamp Sockets: ZOT includes Industrial Style Spring Loaded lamp sock-ets designed to extend lamp life and prevent lamps from shaking loose and shatter-ing on the pindeck. (see illustration)High Power Ballast: Each ZOT fixture includes Two High-Power Ballast’s that yieldreliable service and a wide range of power supply.Compatibility: The ZOT Ballast’s are compatible with the original AMF lamps,enabling reuse of lamps you already have. And the mounting holes on the ZOT fix-ture are of the same dimensions as the original AMF 82-70 Single lamp fixture.Switching Options Suit Your Needs: ZOT offers the option of switching from Sportto Recreation (Glow) Bowling from the Front to Desk or the Rear of the Pinsetter.Light Reflective Finish: ZOT’s Unique formula Ultra-White finish reflects a highdegree of Ultra-Violet light onto the pindeck.ZOT’s Two-Lamp Glow Pindeck light fixtures are recommended for centers withthe following scoring systems• AMF MagicScore • AMF AccuScore**• AMF AccuScore Plus* • AMF Boss Scoring• Brunswick AS 80 • Other Brands***FrameWorx with VPS Cameras and many other current model scoring systemsavailable from independents, including: Qubica, Steltronic & Twelve-Strike.*May require camera software upgrade - call ZOT for details.

2

Glo

w B

ow

lin

gPro

du

cts

14

Features and Benefits:Replaces toggle switch at rear of Pinspotter with relay controller. Enables switching from White to Black (Glow) light to be managed from the Front Desk, Mechanics Tool Room or any otherremote location as neededEnables switching from White to Black (Glow) Light on up to 24-lanes in unison.

Glow Bowling Products

2

Glo

w B

ow

ling

Prod

ucts

Light Sensitive Processors for AMF Scoring

AccuCam IIProcessors

#400236This processor chip has beendesigned to give the camerathe ability to read pins under both White Light and BlackLight.

This current software development helps eliminate miscountof pins under all light conditions.

AccuCam IProcessors

#400235This processor chip has beendesigned to give the camerathe ability to read pins under both White Light and BlackLight.

This current software development helps eliminate miscountof pins under all light conditions.

Data Cable

Power Cable

Data Cable

Power Cable

Pindeck Light RelayControl#400154

Notes: One Relay Controller operates a pair of lanesRequires one Two-Conductor Wire runs per 24-lanes (notincluded) to connect Front Desk Transformer & Switch Kit toRelay Control at Curtain Wall. Order #312003 (order by thefoot)

Requires #400162 to operate

Transformer & Switch Kit#400162 (115V/60Hz)

#400212 (230V/50Hz)Transformer: Plugs into wall outlet and supplies power to theRelay Controller

Notes: One transformer and switch kit can operate up to 24-lanesSome overseas applications may require a different transformer tothose listed. If the transformer is being sourced locally, to purchasethe Switch and Mounting Box only, order: #400163

Upgrades for ZOT Dual Pindeck Lamp FixturesThe two kits listed below are used to convert switching ZOT Two-Lamp Glow Pindeck Lights from the rear of the machine to thelocation of your choice (e.g., the Front Desk)

Curtain Wall

Wires extend toRelay Control

Lane 6Lane 5 Lane 4

Lane 3 Lane 2 Lane 1

Wires extend to Light fixtures(Included)

Wire extends toTransformer Switch Kit

15

Glow Bowling Products

Item ZOT # Description1 290015 Single Lamp Ballast (115Volt / 60Hz)

(5-wire multi purpose 30 Watt)

2A 240010 “36” Lamp F30 T8 BLB (Black Light Blue)”

2B 240015 “36” Lamp F30 T8 BL (Black Light)”2C 240012 “36” Lamp F30 T8 D (Day Light)”3A 300023 Toggle Switch (SPDT) (Rear Machine Control)3B 300026 Toggle Switch (DPDT) (Front Desk Control)4A 620160 Switch Bracket (Rear Machine Control)

Item ZOT # Description4B 400161 Switch Bracket (Front Desk Control)5 330029 Spring Loaded Lamp Socket (ZOT)6 330030 Stationary Lamp Socket (ZOT)7 620159 ZOT Ballast Cover8 431049 PC Board Only (ZOT Relay Controller)9 312003 Wire 2 Conductor 18 Gauge (Order by the foot)10 400160 Transformer (Front Desk Control)11 440058 Wire Harness 2 Conductor 14ft. (Relay Controller)

Spare Parts for Pindeck Lights

Note: To order individual parts refer to parts grid shown below

1 4A

1011

2C

2A, B

3A

5

6

4B 3B

9

8

7

2/3

Glo

w B

owlin

g &

Un

iqu

e Pa

rts

Tired Of Flat Gutter Related Ball And Pin Damage?…Tired Of Re-drilling Holes To Re-Anchor Flat Gutters?

With ZOT’s Threaded Steel Flat Gutter Anchors there’s nomore need to redrill flat gutters that have become loose.ZOT’s Threaded Steel Flat Gutter Anchors are a perma-nent solution to this age old problem.

Flat Gutter Anchor#420343 Complete One-Lane Kit(Includes hold down screws and 4-Threaded Steel Flat Gutter Anchorsfor tail-plank end, & 4 Anchors for cross foundation to secure 2 x FlatGutters)

#420361 Individual Anchors, Tail Plank End

#420362 Individual Anchors, Cross Foundation

16

Unique Parts

3

Un

iqu

e Parts

Increased Safety in the Work Place: No more hazardousclimbing up the rear of AMF Pinspotters. ZOT Steel Steps,which feature Diamond Plate Tread on the Risers, makeaccess to your pinspotters easier and safer than its ever been.

Easy Installation: ZOT’s All Steel Steps simply bolt onto theback of the machine, using existing holes, and hangs on therear elevator.

Does not turn the Back End Aisle Space into an ObstacleCourse: The mounting of the steps, which projects approxi-mately 6" (.16M) from the back end of the machines, beginat the level of the first riser, leaving the aisle and floor spacefree for easy access and cleaning.

Note: The Steps for AMF 82-30’s can be unhooked, and lifted fromthe machine, without removing any bolts.

#420318for AMF 82-30’s

#420286for AMF 82-70’s

Steel StepsIf climbing onto your pinspotters seems like climbing Mount Everest… Install ZOT’s all Steel Steps – Today!

#420290for AMF 82-90’s

Front Mounted Steel StepsFor AMF 82-70 & 82-90 Pinspotters#420468

“Introducing a New Product at an Introductory Price”This is the product mechanics have been asking for – Steel Steps that enable easyand safer access to AMF 82-70 & 82-90’s from the front of the pinspotter.

Features and Benefits:

Easy to Install: The steps simply hook in place and can easily be moved to anoth-er pair of lanes.Easy and Safer Access to the Pinspotter: From the front of the machine, saving time and energy or attempting to scale the machine by standing onmachine parts.Suitable for all 82-70 & 82-90 Installations: Where the mask unit is mountedapproximately 2-feet (or more) from the front of the Pinspotter.

Features and Benefits:

17

Features and Benefits:

Virtually no down time: If the center tube of the cushion breaksthe machine can be fully operational within minutes with a ZOTRepair Kit.Temporary or Permanent Repair: It’s your choice. The ZOTCushion Support Center Tube Repair Kit enables you to make aninstant repair.Universal Application: The repair kits fit either left or righthanded machines and any brand of cushion weldmet.Easy to Install: No welding – No dismantling – Bolt-on applica-tion that only requires adding nuts to two U-Bolts for either atemporary or permanent repair.

Features and Benefits:Virtually no down time: If either end of the cushion weldmet breaks the machine can be fully operational within minutes with a ZOTRepair Kit.Temporary or Permanent Repair: It’s your choice. The ZOT Cushion Weldmet Repair Kit enables you to make an instant temporaryrepair. At a more convenient time you can add ZOT’s Universal Mount Plate (included in the kit) for a permanent repair solution.Universal Application: The repair kits fit either left or right handed machines and any brand of cushion weldmet.Easy to Install: No welding – No dismantling – Bolt-on application for either temporary or permanent repair.

Unique Parts

3

Un

iqu

e Pa

rts

Cushion Weldmet Repair KitFor AMF 82-70 Pinspotters #420344

(Ball Door Side)Here’s the (Temporary) Fix Here’s the (Permanent) Fix

#420345(Opposite Ball Door Side)

Here’s the (Temporary) Fix Here’s the (Permanent) Fix

Clamp betweensponge and plank

Hook between cushioncover and plank

Lift plank to secure U-Bolt

Lift plank tosecure U-Bolt

Lift plank tosecure U-Bolt

Clampbetween

sponge andplank

Hookbetweencushion

cover andplank

Clamp betweensponge and plank

Hook betweencushion cover

and plank

For Breaks

Cushion Support Center Tube Repair Kit#420019For AMF 82-70 Pinspotters

#420189

1/2”

5/8”

#420190

Features and Benefits:Engineered for Ease of Adjustment: With ZOT’s AdjustableBin Strap, matching the height of the Bin to the Shuttle andTable is no longer a major task.

Saves Time: Gives the mechanic a quick and easy way tomaintain Bin adjustments.

Decrease Parts: Eliminating the (4) rubber bumpers with (1)bolt-on pin protector.

Increase Pin Life: ZOT’s Blue Diamond Series Urethane PinProtector adds to the life of your pins.

Eliminate Double Shuttles: By adding ZOT’s optional Bolt-onGuide Plate (#420401).

18

Unique Parts

3

Un

iqu

e Parts

Adjustable Bin Strap KitFor AMF 82-70 Pinspotters

#420400

ZOT’s Adjustable Bin Strap Kit solves multiple Bin, Shuttleand Table problems with a single product.

adjustable #420400

Suitable for:All 5 Carpet Drive Belts (1/2")Ball Elevator Drive Belt 58" (1/2")Ball Rudder Secondary Belt (1/2")PBL Rudder Drive Belt 40" (1/2")PBL Rudder Drive Belt 38" (1/2")PBL Rudder Ratchet Belt 45" (1/2")Spectrum Ball Lift 'V' 70" (1/2")Spectrum Ball Lift 'V' 36" (1/2")Sure Pik Motor to Pulley 47" (1/2")Pin Elevator Belt (5/8")

Link BeltTired of having to stock dozens of V-belts in dozens of different lengths…only to find you’re missing the one youneed, when you need it most? Purchasesboth sizes (1/2” & 5/8”) of ZOT Link Beltsand you’ll no longer need to worrywhether you have the right combina-tions of matching belt lengths in inven-tory. ZOT’s Link Belt comes in 20-footlengths per box, and, with a simple twistof the wrist, you’ll have a belt that’s aperfect fit for your needs.

#420401

Features and Benefits:Permanent Replacement of endless and spliced V-belts.

Eliminates Needs to stock extensive line of replacement belts.

Easy Installation without dismantling pinsetter drives.

Extended Life because of Oil and Chemical resistantcomposite polyurethane/ polyester construction.

#420477(for 5-pin)

3

Un

iqu

e Pa

rts

19

Unique Parts

ZOT Front Ball Lift Relay BoxFor all centers with Brunswick ‘S’ StyleFront Ball Lifts with two Lift Wheels/Tires

# 400208

ZOT’s Front Ball Lift Relay Box is a direct replace-ment for the relay box on all Brunswick ‘S’ StyleFront Ball Lift Assemblies with two Wheels or Tires,including AMF, Brunswick, Murrey and Vantage.

Check out these benefits:Easy to Service: The entire relay PC Board can be changed in minutes.

Easy to Install: The relay box can be changed inminutes. All wire connections feature solderless fittings.

Simple Design: Eliminates expensive military style connector

Circuit Protection: The Motor Circuit features aresettable breaker: When a ball-jam occurs simplyclear the jam and reset the breaker.

Enhanced Ball ReturnAssembly Pad KitFor AMF 82-30 & 82-70 Pinspotters with KickerStyle Ball Returns

#420402ZOT's specially formulated Blue Diamond Urethane EnhancedBall Return Assembly pads solve a myriad ball return problems.

Features and Benefits:

Engineered for More Positive Ball Return: A pad featuring aseries of Positive Drive grooves create a ratchet like affectto the ball return, and two Pressure-Control pads increaseball-surface contact with the kicker wheels.

Fewer Ball Calls: The ZOT Ball Return Pads significantly enhancethe assembly’s ability to return ball after ball after ball.

Faster League Times: With fewer balls rolling back intothe pit carpet area league times are significantly reduced.

Increased Customer Satisfaction: Faster league times withfewer ball-calls makes the game that much more enjoyable.

Features and Benefits:

Saw Tooth: Designed to create a Ratchet like affect that pre-vents ball slippage, thereby ensuring a positive drive to thekicker wheel.

Urethane Formula: The Urethane used in ZOT’s Saw ToothKicker Wheel, is formulated to retard oil and have incompara-ble gripping power.

Hexagonal Insert: The Hexagonal Center Mounting Hub isdesigned to reduce the possibility of tear out.

Universal Design: ZOT’s Saw Tooth Kicker Wheel will workeffectively on odd or even lanes without being affected bythe direction of rotation.

“Try One”

Saw Tooth Kicker Wheel#680001

ZOT’s Saw Tooth KickerWheel has design fea-tures that significantlyimprove the performanceof AMF 82-30 & 82-70Pinspotters with KickerStyle Ball Returns.

New UrethaneFormula

20% softer for superior ball grip.

4

Foul Detectors

20

Foul Detectors

Wizard Foul Detector and Cover’s Package#400167

Package includes: ZOT’s Wizard “Plus” Foul Detector & One Wide and One Narrow Black Metal Cover

“Replacing Foul Detectors improves the Bowler’s Experience...Replacing Foul Detector Covers Improves the Image of your Center”

For individual product information,including features and benefits,See pages 21 and 22.

The ZOT’s Wizard ‘Plus’ Foul Detector is universally recognized asthe most reliable product in the industry. No other brand canmatch the features included in the ZOT product.

Featurefor feature...Dollar for dollar...the best deal in the market

How to select the right Foul Detector product for your center

In the following five pages you willfind details of ZOT’s fine line of WizardFoul Detector products, which fall intofour categories.

Identify which Foul Detector is the bestfit for your center in the grid to theright and then go to the appropriateproduct page to find all the details.

The ZOT’s Wizard ‘Plus’ Foul Detector isuniversally recognized as the most reli-able product in the industry. No otherbrand can match the features includedin the ZOT product.

? Subway (Underlane) Ball Returns Replacement for AMF Radaray 82-68, 82-94, 82-120 & Radaray Plus

Subway Ball Returns with no 115 V available atthe foul line (replacement for AMF 82-08 Radaray)

Surface (overlane) Ball Returns (replacement for AMF82-08 Radaray)

Modification (Upgrade) for AMF 82-120 RadaraySystems

Wizard Plus #400143(See Page 22)

Wizard Low Voltage #400119 (See Page 23)

ZOT Wizard Surface #400031 & 400015(See Page 24)

Wizard Enhanced P.C. Board #400074 & Wizard InfraredHead Conversion #400076 (See Page 21)

3

3

3

3

4

Foul

Det

ecto

rs

Foul Detectors

21

Wizard Metal Foul Detector Covers#420295 (Wide) Ball Return Cover/Black#420296 (Narrow) Divider Trim Cover/Black#420191 (Wide) Ball Return Cover/Aluminum#420192 (Narrow) Divider Trim Cover/Aluminum

Removed Original Parts

Wizard Enhanced P.C. Board#400074

Wizard Infrared HeadConversionFor AMF 82-120 Radaray Systems

#400076

Enhanced P. C. Board

Foul Line Measure as shown

Infrared Head

Replacement forAMF RadaraySystems: with 9-5/8”(.244M) Trim End toFoul Line, including:AMF 82-68, 82-94,82-120 and currentproduct line.

Features and Benefits:

Simple Plug in Installation: The ZOT Enhanced P.C. Board simply plugs into the existing equipment, with no modification nec-essary.Alignment Indicator: A 4-unit LED system indicates when the signal is strongest. This aids the installer and the mechanic,should realignment ever be necessary.Self Diagnostics: ZOT’s exclusive micro processor circuit automatically checks sensor signal levels every time you switch the uniton, and every time there is a foul.Easy Conversion to Infrared: The ZOT P.C. Board operates with the original photo cell and bulbs, but it also includes the drivecircuit for Infrared sensors. The ZOT Infrared Sensor Source is Solid State Diode rated for millions of hours of dependable serv-ice – a great improvement over the 2,000 hours rating of the old incandescent bulbs.Easy to Install: The ZOT Infrared Head Conversion simply plugs into the ZOT Enhanced P.C. Board.All the Features of the ZOT Wizard: That’s what you get when you complete your upgrade and combine the ZOT P.C. Boardwith the ZOT Infrared Head.

Features and Benefits:Vinyl Finish: Available in Black or Aluminum.Rugged Construction: ZOT’s Metal Foul Detector Covers are designed and manufactured for decades of trouble free service.

4

Foul Detectors

Foul Detectors

22

Infrared Technology: The ZOTWizard ‘Plus’ features an infraredsensor that is solid state and ratedfor millions of hours of dependableservice. Infrared sensors eliminateold incandescent bulbs.

Alignment Indicators: A 4-unit LEDsystem indicates signal strength. Thisaids the installer and/or mechanic inthe alignment of the sensors.

Automatic Scoring Compatible: ZOTWizard Foul Units transmit the prop-er signal needed to communicatewith automatic scoring systems.Changing the signal is as easy as:either flipping a switch.

Marginal Signal Alert: ZOT WizardFoul Units will alert the mechanic topending problems. Four differentsequences of buzzer signals canoccur if the unit has a failure allow-ing the mechanic to troubleshoot.

All Modular Design: All the individualcomponents simply plug onto the PCBoard, making troubleshooting andthe replacement of parts simple.

Self Diagnostics: ZOT’s microproces-sor automatically checks the sensorsevery time there is a foul. If the anyWizard unit detects a problem it willautomatically turn itself off. . . onelane at a time.

(continued on next page)

Wizard ‘Plus’For AMF Subway Ball Returns#400143

115V - 230V Switch

Vibration Protected

All Modular Design

Alignment Indicator

Only Available from ZOT. No other manufacturer or supplier offers afoul detector unit that even comes close in terms of features and benefits.Check it out for yourself.

Replaces AMF Radaray 82-68, 82-94, 82-120 & RadarayPlus

Multi-Voltage/Multi-Cycle: TheWizard ‘Plus’ operates at either115V/60Hz or 230 V/50Hz with aflip of a switch.

Wizard ‘Plus’ and Wizard Low Voltage Features and Benefits:

Wizard ‘Plus’ Spare Parts:Description Part NumberSpare Parts Kit #400137PC Board #431043Fuse #400110Sensor Assembly #431015Reflector Only #800057Reflector Assembly #400052Power Harness #440051Scoring Harness #440049Buzzer #400111Transformer #431040

4

Foul

Det

ecto

rs

Foul Detectors

23

Alignment IndicatorSeparate Transformer and Wire Run

Cover: Standard Cover Color - Black.Also available with Aluminum finish

Matching Narrow Cover, order separately

#420296

Wizard (Low Voltage)#400119

Kit Includes: Detector Assembly, Wide Metal Detector Cover (black),Transformer, Power Supply Cable, Scoring Communication Cable, 2 ReflectorAssemblies and All Mounting Hardware to install complete kit.

Note:If your pinspotter requires 120 VACto sweep the pins after a foul, con-tact ZOT for a conversion box(#400100)

Kit Requires: A standard 115 Voltduplex outlet to plug the trans-former into for supplying power tothe Foul Unit. e.g. curtain wall.

Low Profile: Built for subway ballreturns, serving two-lanes, the Wizard‘Plus’ fits under most major brands ofexisting wide ball return covers.

Microprocessor Efficient: All ZOTWizard Foul Units have State-of-the-ArtMicroprocessor technology. This simpli-fies the circuitry, making all WizardUnits more cost effective and reliable.

Light Source Recognition: ZOT’sinfrared design features a special oper-ational frequency for its emitter andreceiver communications. Matching thisfrequency eliminates an affect fromalternate light sources: e.g. overheadlighting, and cosmic/glow lighting.

Vibration Protection: The PC Board ismounted on a shock-absorbingbuffer to minimize ball impact vibra-tion that can damage delicate cir-cuitry common to PC Boards.

Wizard Low Voltage Spare Parts:Description Part NumberSpare Parts Kit #400114PC Board #431035Sensor Assembly #431015Reflector Only #800018Reflector Assembly #400060Power Harness #440043Scoring Harness #440041Buzzer #400111Transformer #400065AMF Wide Black Cover #420295

(continued)

4

Fou

l Detecto

rs

Foul Detectors

24

Features and Benefits:

Infrared Technology: ZOT Wizard Foul Units featureinfrared sensors that are solid state and rated formillions of hours of dependable service. Infraredsensors replacing troublesome incandescent bulbs.Self Diagnostics: ZOT’s microprocessor automaticallychecks the sensors every time there is a foul. If anyWizard Foul Unit detects a problem it will automati-cally turn itself off . . . one lane at a time.Alignment Indicators: A 4-unit LED system indicatessignal strength. This aids the installer and/ormechanic in the alignment of the sensors.All Modular Design: All the individual componentssimply plug onto the PC Board, making trou-bleshooting and the replacement of parts simple.Vibration Protection: The PC Board is mounted on ashock-absorbing buffer to minimize ball impactvibration that can damage delicate circuitry com-mon to PC Boards.Marginal Signal Alert: ZOT Wizard Foul Units willalert the mechanic to pending problems. Fourdifferent sequences of buzzer signals can occur ifthe unit has a failure allowing the mechanic totroubleshoot.Microprocessor Efficient: All ZOT Wizard Foul Unitshave State-of-the-Art Microprocessor technology. Thissimplifies the circuitry, making all Wizard Units morecost effective and reliable.Automatic Scoring Compatible: ZOT Wizard FoulUnits transmit the proper signal needed to commu-nicate with automatic scoring systems. Changingthe signal is as easy as: either flipping a switch ormoving jumpers to a different set of pins.No need for an Electrician to Install: The ZOTWizard (Surface) comes with a Transformer andLow Voltage supply cable allowing a Mechanic tocomplete the installation with no added help.Light Source Recognition: ZOT’s infrared designfeatures a special operational frequency for itsemitter and receiver communications. Matchingthis frequency eliminates an affect from alternatelight sources: e.g. overhead lighting, andcosmic/glow lighting.

Wizard (Surface)Replaces AMF 82-08 Radaray & For AMF Surface Ball Returns

#400015 (Serving Two Lanes)

#400031 End Unit (Serving One Lane)

Kit Includes: Detector Assembly, Narrow Metal Detector Cover (Silver),Transformer, Power Supply Cable, Scoring Communication Cable, 2Reflector Assemblies and All Mounting Hardware to install complete kit.

Vibration Protection Alignment Indicator

Reflector includedin ZOT Kit

Double UnitSingle Unit

Ais

lew

ay/P

illar

s

Bal

l Ret

urn

Bal

l Ret

urn

Bal

l Ret

urn

Single Unit

Single Unit

Original Cover

Single Unit

Kit Requires: A standard 115 Volt duplex outlet to plug the transformerinto for supplying power to the Foul Unit. e.g. curtain wall.

ZOT Foul Detector

Wizard Surface Spare Parts:Description Part NumberSpare Parts Kit #400113PC Board #431025Sensor Assembly #431027Reflector Only #800018Reflector Assembly #400060Lamp (Pkg. of 10) #400094Lamp Socket Assembly #440020Power Harness #440043Scoring Harness #440041Buzzer #400111Transformer #400065

4/5

Fou

l Det

ecto

rs&

Tri

gg

erin

g

Foul Detectors

25

Wizard and Conversion (Spare Components)A B C D E F G H I J K

NEW Old LampKit Kit P.C. Sensor Socket Power Scoring Reflector Reflector Trans-

Item Number Kit Description Number Board Fuse Assembly Lamps Assembly Harness Harness Assembly Only Buzzer former

1 A 400143 Wizard Plus 60800-0 431043 400110* 431015 N/A N/A 440051 440049 400052 800057 400111 431040B * Wizard Double 60200-0 431034 400110* 431015 N/A N/A 440051 440039 420088 800018 400111 N/A

2 A 400119 Low Voltage 60700-0 431035 N/A 431015 400094 440020 440043 440041 400060 800018 400111 400065Wizard (10 ea.) (75 ft.) (1RH & 1LH)

3 400015 Wizard Surface 66200-0 431025 N/A 431027 400094 440020 440043 440041 400060 800018 400111 400065(10 ea.) (75 ft.) (1RH & 1LH)

4 400074 Radaray P.C. Board 62200-0 N/A N/A N/A N/A N/A N/A N/A N/A N/A N/A N/AUpgrade

5 400076 Radaray Infrared 69200-0 N/A N/A 431019 N/A N/A N/A N/A 400060 800018 N/A N/AHead – Add On (1RH & 1LH)

Electronic Triggering (Spare Components) NEW Old Flat SensorKit Kit P.C. Sensor Sensor Power Gray Coaxial Trans- Sensor Lens

Item Number Kit Description Number Board Fuse Blue Gray Harness Cable Cable former Shims Kit

6A * ET 2000 Two-Lane 48050-0 432052 N/A 400001 400133 N/A 450005 N/A 290005 400121 400032Electronic Triggering (115V) (25 ea.)

B * ET 2000 Two-Lane 48150-0 432052 N/A 400001 400133 N/A 450005 N/A 290006 400121 400032Electronic Triggering (230V) (25 ea.)

7A 400135 ET 2001 Two-Lane 48250-0 432052 N/A 400001 400133 N/A 450005 N/A 290005 400121 400032Electronic Triggering (115V) (25 ea.)

B 400034 ET 2001 Two-Lane 48350-0 432052 N/A 400001 400133 N/A 450005 N/A 290006 400121 400032Electronic Triggering (230V) (25 ea.)

8 * Mini Magic – AMF 43050-0 400009 400083 400001 400005 440014 450001 450002 N/A 400121 400032(6 ea) (25 ea.)

Note: Wizard & ET 2000/ET 2001 Spare Parts KitsA Plus: 400143 – Order: 400137 D Surface: 400015 – Order 400113B Double: 60200-0 / 60400-0 / 60600-0 – Order 400112 E ET 2000: 48050-0 – Order 400138C Low Voltage: 400119 – Order 400114 F ET 2001: 400135 – Order 400138

*Product Discontinued

In the Chart below you will find details of ZOT’s replacementSpare Parts for Foul Detector and Triggering related products.

Spare PartsZOT’s Foul Detector, Scoring and Electronic Triggering relatedproducts are Unique in the industry because they are modularby design, enabling the mechanic to replace the various com-ponents — right there in the bowling center.

A

K

K

C

D E

G

J

G

I

F

H

#400060

A

BF

#420088

#400052

5

Ele

ctron

icTrig

gerin

g

Electronic Triggering

26

ET 2001 “Dual Lane” Ball Detector#400135 (115V/60Hz) #400034 (230V/50Hz)

Alignment LED’s

Remote Trigger Ports

Note:The ET 2001 has two adjustable time delay outputs, each of which serve two lanes.

Triggering Improvements that Promote Bowling

ZOT’s ET 2001 “Dual Lane ElectronicTriggering, for AMF Pinspotters fea-tures: an adjustable time-delay from3/4 of a second to 8 seconds and themost advanced infrared technologyavailable in the industry, to guarantee100% positive triggering . . . ball afterball after ball . . . you know it makessense.

It only takes a few seconds a game tosave thousands of dollars a year in lostlinage, revenues, power consumption,and machine wear and tear – and toimprove customer satisfaction levels.

At bowling centers everywhere, yousee youngsters, seniors, and bowlersusing light balls – especially in centerswith bumper bowling – frustrated, andwasting time, either because they’reslow to react in pressing the reset but-ton, or because they don’t know whatto do, when the machine fails to cycle.

That same few seconds will pay forZOT’s ET 2001 “Dual Lane” ElectronicTriggering system several times over inits first year, and, thereafter, the addi-tional revenues, savings and improvedcustomer relations, translate into clear,and measurable, increased profits.

Features and Benefits100% Positive Triggering: Regardless ofthe weight or speed of the ball.

Reduces Maintenance: Mechanical link-age does not affect trigger sensitivity.

World Class P.C. Design: ZOT’s newMicro-Processor technology simplifiesthe circuit, making the ET 2001(Electronic Triggering) Dual Lane BallDetector surprisingly cost efficient.

Superior Sensor Design: The ET 2001retains the same sensor design as ZOT’ssingle lane Magic Eye. With more than adecade in the marketplace, this minia-ture and ruggedly constructed sensorsystem has a proven track record of mini-mizing damage by balls and pins; and it’snot sensitive to vibration.

Infrared Technology: The ET 2001 fea-tures an Infrared Sensor source that’sSolid State Diode Rated for millions ofhours of dependable service.

Alignment Indicator: ZOT’s ET 2001features an exclusive 4-unit LED sys-tem, that indicates when the sensorssignal is strongest. The LED’s can beviewed from either the sensor area, orfrom the top of the pinspotter, with-out opening the cover.

Diagnostic Indicator Safety System: ZOThas added an LED system which indi-cates when an output signal is occur-ring.The ET 2001 has a built-in SafetySystem which prevents the machinefrom cycling if a person is in the areawhere the sensors are mounted.

Speeds Up League Play: No more push-ing the reset button.

Profit on Machinery Improvement:Over 200% return on investment thefirst year.

(continued on next page)

5

Ele

ctro

nic

Trig

geri

ng

Electronic Triggering

27

ZOT Unit Replaces twoBrunswick #57-214904-000

ET 2001 Add-on Scoring OptionFor Centers with AMF Pinspotters and Brunswick ScoringIf you’re dissatisfied with your present AS80 and AS90 Series Ball DetectSystem, the ZOT ET 2001’s ability to double as an improvement to your automatic scoring system makes it the most cost effective ball detect system available.

The following are the wire harness options necessary to activate the automatic scoring ball detect feature:

#400159 for Brunswick AS 79 Scanner

#440080 for Brunswick AS 86 Scanner

#400194 for Brunswick AS 90 Camera & FrameWorx

ZOT Unit Replaces 79Scanner Ball Detect

Sweep Lock-Out(Micro-Switch and harness)

#400216ZOT’s Sweep Lock-out resolves intermittentmultiple cycling (e.g., Sweep Reversal), whichcan occur when the sensors are mounted inthe sweep path sensor mounting zone.

Guard Position

Gray Block

Blue Block

Sensormountingzone

Note:The above wire harness options are only compatible toZOT ET 2001.

ET 2000 & ET 2001 Spare Parts 115V & 230V:Description Part NumberSpare Parts Kit #400138PC Board #432052Blue Emitter Block #400001Flat Gray Emitter Block #450005Gray Receiver Block #400133Transformer for 115V #290005Transformer for 220V #290006Sensor Shims #400121Sensor Lens Kit #400032

OptionalAdd-onProduct forET 2001

OptionalAdd-on

Product for

ET 2001

Features and Benefits:(continued)

Remote Trigger Ports: ZOT’s ET 2001can be triggered by external sources,e.g., scoring system remote switch.

Control Box Protection: ZOT’s DualLane Control Box mounts on the backof the masking unit curtain wall; outof the way of potential damage byballs or pins.

Flip Top Cover: The Control Box Coverhinges from the top, which means noscrewdriver is needed to view the P.C.Board. Simply flip the cover up forinspection, and down again when fin-ished.

Simple Installation: ZOT’s ET 2001 installsin three easy steps:

1. Wall transformer plugs into 115Volt outlet for power supply.

2. Two conductor outputs for eachpinspotter simply quick-splice tothe bowlers reset button wires.The AMF trigger switch caneither be retained…or disman-tled.

3. The Infrared Emitter andReceiver are simply plugged in,leveled and secured at eachlane.

All Modular Design: All componentsplug into the P.C. Board separately,making it possible and easy to changeparts, and troubleshoot.

Rake/Sweep Path Sensor Mounting:The Sensors can be mounted behindthe Sweep (in the Sweep path), withaddition of option #400216. See upperright.

6

Lane Pro

du

cts

28

Lane Products

ZOT PermaDeck Back-End Lane Products

ZOT Pinsetter Parts is pleased to introduce a new line of backend lane products including flat gutters, kickback plates, edgeboards and tail plank tops. All of these products are made fromindustrially engineered HDPE (High Density Polyethylene) As thename would imply, HDPE is durable, requires no maintenance,and it never needs recoating with finish. To maintain qualityand durability none of ZOT’s HDPE products use recycled materi-als. ZOT’s back end lane products are also ABC approved.• ZOT’s Kick Back Plates are undrilled enabling the installer to

drill holes and screw the kick back plates into kick back sur-faces where there are no old or enlarged holes, ensuring asecure installation

PermaDeck Flat Gutter Kit For AMF & Brunswick

#420479 (for one lane)

Check out these features:

• Costs less than comparable products.• Virtually maintenance free and durable.• Made of 1” thick “Warp Resistant” HDPE for maximum

strength and life. Note: less expensive brands use 3/4” plasticwhich tends to warp and has a much shorter lifespan.

• Easy to install: either by the center mechanic or a laneresurfacer.

ZOT PermaDeck Kickback PlatesFor AMF & Brunswick(Black & Undrilled)

#42048215” x 33” fits all AMF and early modelBrunswick

#42048319” x 23 3/4” for early model Brunswick

#42048416” x 40” for late Brunswick

Check out these features:

• Highly durable.• Restore your kickbacks to ABC

Specifications.• Improves scorability and reduces pin

damage. • Easy to install.

ZOT PermaDeck Tail Plank TopsFits AMF & Brunswick Wood Pindecks

#4204811 3/4” x 1 1/2” x 43” (per lane)

#420511Fits Brunswick & Synthetic/HPLPindecks1/2” x 2 3/8” x 41 7/8”

Check out these features:

• Restores your tailplanks to ABCSpecifications.

• Improves scorability.• Extend the life of your pins.

ZOT PermaDeck Edge Boards Fits AMF & Brunswick Wood Pindecks

#4204801” x 2 1/2” x 46” (each)

#420510Fits Brunswick & Synthetic/HPLPindecks1/2” x 2 3/8” x 47 5/8”

Check out these features:

• Restores your wooden pindecks toABC Specifications.

• Helps improve scorability.• Extends the life of your pins.

NEW

Part # DescriptionQuarter Round Trim, GlowRod & Glow Dowels

800151 Quarter Round Trim

GLOW ROD for installing in Fascia (add to per foot price of fascia)

420493 Glow Rod — Yellow/Green

420494 Glow Rod — Green

420495 Glow Rod — Red

420496 Glow Rod — Orange

GLOW DOWELS for installing in Fascia

420501 Glow Dowels — Four Dowels per foot

ZOT’s GlowRod Fascia and Quarter Round Trim products aredesigned to improve the appearance and highlight the riseror step from the bowlers settee area to the approach. TheGlowRod Fascia and Quarter Round Trim (shown in the illus-

tration below) clearly highlights the riser in either a Glowor Non-Glow Bowling environment which, in addition toenhancing the image of your center, brings safety to theequation too — especially during Glow-Bowling activities.

GlowRod Fascia & QuarterRound TrimCheck these features:Improved Safety: The GlowRod Fascia illumi-nates in an Ultra Violet (Glow Bowling) light-ing environment, clearly highlighting the riseror step-up to the approach. The UV additivein the rod will Glow under Ultra Violet Lightwith no additional power necessary.

Durable: Made of virtually indestructibleindustrially engineered HDPE (High DensityPolyethylene) that will outlive the life of yourapproaches.

Maintenance Free: ZOT’s GlowRod Fascia andQuarter Round Trim never needs painting,and will look good for 10-15 years withoutcracking or splitting.

Cost Effective: Costs about the same asreplacing the original, and less durable, wornand damaged maple fascia.

Note: ZOT’s GlowRod is sold by the foot andseparately from the Fascia. See below for colorselection and part numbers, etc.

How it all works: You start by measuring theheight of the riser (step) from the settee areato the the approach, and then the length ofthe fascia needed to extend across the widthof the approaches.Note: Fascia and Quarter Round Trim (with orwithout GlowRod) is a custom product that’s“Made-to-Order”.

Once you have the specifications and placean order with ZOT it will take a few weeksto process (custom build) and ship the fin-ished product.

ZOT GlowRod Fascia and Quarter Round Trim for Approaches

NEW

Here are three options:

Option 1ZOT’s HDPE Fascia and Quarter Round Trim is designed to be used as areplacement for the original wood fascia.

Option 2HDPE Fascia and Quarter Round Trim is also available with a groove toaccommodate the installation of a Glow Rod, which is an optional add-on.

Option 3Glow Dowels can also be added to either Option 1 or 2.

• Glow Dowels are factory installed in the Fascia• All orders for Fascia include Mounting Screws Fascia, Quarter

Round Trim and GlowRod are shipped in 5-foot lengths andcan therefore be shipped by UPS

6

Lan

e Pr

od

uct

s

Lane Products

29

Part # DescriptionFascia With & Without Quarter Round Trim(Order Glow Rod and Glow Dowels Separately)

800137 1” NO/Quarter Round Trim –NO GLOW

800138 1.5” NO/Quarter Round Trim – NO GLOW

800139 2” W/ Quarter Round Trim

800140 2.5” W/ Quarter Round Trim

800141 3” W/ Quarter Round Trim

800142 3.5” W/ Quarter Round Trim

800143 4” W/ Quarter Round Trim

800144 4.5” W/ Quarter Round Trim

800145 5” W/ Quarter Round Trim

800146 5.5” W/ Quarter Round Trim

800147 6” W/ Quarter Round Trim

800148 6.5” W/ Quarter Round Trim

800149 7” W/ Quarter Round Trim

800150 7.5” W/ Quarter Round Trim

30

Ball Conditioner Products

7

Ball C

ond

itioner

Prod

ucts

ZOT “GlossBoss”Coin-Op Ball Conditioner#420397

ZOT is pleased to introduce the all-new feature rich “GlossBoss” BallConditioner …a Coin-Operated machine that can generate revenues foryour center or pro-shop … even when you’re not there.

Scrolling Color Message & Advertising Display

Customer Friendly Display

Bill Acceptor

Mechanical Compound Advance System

Easy to Program Control Box

Buffer Pressure Meter

Unique Easy-Adjust Buffer Shaft

Electronic Coin Validator

®

Only included in machines for USA

(continued on next page)

Ball Conditioner Products

7

Bal

l Co

nd

itio

ner

Pro

duct

s

31

Yes…you can make moneywith a Ball ConditionerIf you’re not making money with your ball conditioner…it’s because:You don’t have oneThe one you have is out of orderThe one you have doesn’t polish ballsYou’re charging a 1950’s/1960’s priceYou don’t have a ZOT “GlossBoss” Ball Conditioner

Promoting your Ball Conditioner Pay Attention and Keep theBall Conditioner in Adjustment: This is really easy to do, yet it’sthe number one reason ball conditioners do not yield theirpotential in terms of revenues and profits. If a ball conditionerdoes not polish balls, bowlers won’t use it. It’s as simple as that.Promotion, Promotion, Promotion: Typically a ball conditioneris used by about 6 percent of bowlers a week, providing ofcourse, the unit functions properly. With just a little promo-tion, this percentage can be substantially increased.

Features and BenefitsCustomer Friendly Display: The customer dis-play screen shows price, money’s deposited,cycle-time and cycle-time remaining, plushouse-ball and Sold-out modes.Four Easy-to-Program Price Levels: A simpletwo-button operation. Hold down one buttonand pulse the other until the illuminated LCD’son the Display panel show the desired Pricelevels This feature enables you to periodicallyincrease the price as and when desired.Four Easy-to-Program Run Times: A simpletwo-button operation. Enables you to adjustthe run times to maximize revenues and thenumber of users.

Electronic Coin Validator: Programmable forpromotional tokens and single coins of anydenomination (e.g. Quarters or Dollar Coins inthe US) and most currencies, subject to size(maximum 34mm diameter and 3.4mm thick).Bill Acceptor: ZOT’s internally mounted BillAcceptor will typically increase machine usageanywhere from 15 – 30 percent. A ZOT BillAcceptor also reduces the frequency in makingchange for customers, and makes cashing outthe machine easier.Mechanical Compound Advance System: Atime tested proven system makes it easy tomaintain a high quality polish without the con-stant need for adjustment and readjustment.Easy-Adjust Buffer Shaft: Enables you to easilyset the buffing wheel adjustment correctly andguarantee the Ball Conditioner “Really PolishesBowling Balls”, ball after ball after ball. Simplyloosen six bolts and rotate a calibrated jackscreweach time the compound block is replaced.Double-ended Bearing Support on BuffingWheel: Makes wheel replacement easy andyields a smooth running operation withoutthe tricky balancing exercise required witholder machines.Scrolling Message and Advertising Display:This easy to program multi-color digital dis-play enables centers to develop their ownpromotional and advertising messages totheir customers.Buffer Pressure Meter: Takes the guessworkout of measuring the pressure between thebuffing wheel and surface of bowling ball foroptimal ball polishing performance.

Customer Friendly Display: with LCD display for Price, Coin

Intake, Cycle Time Paid, & Cycle TimeRemaining.

*Bill Acceptor: that typi-cally increases machine

usage by 15-30%

*Replaced with electronic coinvalidatorfor non-USA markets.

Mechanical CompoundAdvance System:

The industries most popular and

dependable CompoundAdvance System.

Easy to ProgramControl Box:enables program-ming and manage-ment of Four Priceand Run Time (Gloss)Levels.

Buffer Pressure Meter:along with ZOT’sUnique Easy-AdjustBuffer Shaft makessetting buffer pres-sure easy and guar-antees a great polishfor your bowlers …every time.

The ZOT GlossBoss II #420398

If you have a small center, or a center with a minimal number of leaguebowlers (e.g. 350 or fewer) or are simply just not ready to invest in amachine that includes all the bells and whistles, ZOT’s new GlossBoss II maybe just the answer.

The GlossBoss II has fewer features than the original machine – but retainsthe same high polishing performance – and all for a price tag that is morethan 20-percent less than a GlossBoss.

“It only takes ‘ONE’ ball polish a day to pay for thelease to buy program on a GlossBoss II machine.”

ZOT Ball Conditioner Restoration and Conversion Kits

If you’re not quite ready for a GlossBoss or GlossBoss II but have an old ball condi-tioner that’s not functioning, ZOT manufactures restoration and conversion kitsthat are compatible to most brands’ ball-conditioners. For more details, see pages 32-35.

(continued)

Ball Conditioner Products

7

Ball C

ond

itioner

Prod

ucts

32

Coin Conversion and Cosmetic Kit#420348*

Front panel Coin mechanism Coin box

Top overlay and ring

Contents:Control Panel: A complete replacement for the original Control Panel, which both

enhances the overall cosmetic appearance of the unit, and brings the followingfeatures and benefits:• Easy-To-Read LCD Price Display.• Coin Intake Level Display (from 1 - 99 coins).• Cycle Time Paid Display.• Remaining Cycle Time Display.• “Sold Out” Display: Indicating that the unit is out of compound.• New Start Switch.

Replacement Control Box: A Solid-State PC Board Driven Control Box that replacesthe original Stepper Coil, and Coin Accumulator. The Control Box also obsoletes theball door motor and its six cam switches. Check out these additional features:• Easy-To-Read, Easy-To-Adjust, PC Mounted Display and Buttons: Makes setting

and changing price and run times as easy as setting a two-button digital clock.• Four Easy-To-Program Coin Intake (Gloss Cycle) Levels:

Giving you total control over coin-cycle time combinations.• House Ball Cycle Time Setting.• Cycle Time Capability: 1-10 Easy-to-Program minutes, in 1-minute increments.• Enables Easy Changeover From 115V Lustre KING, to 230V.• Keeps a Running Total: of money intake and minutes of run-time.

Replacement Ball Door Cover, Handle and Seal: Enables the ball door to be openedmanually, and features an easy-to-change replacement Seal, which does notrequire gluing. The Door Cover and Handle are in a neutral color.

Control Box Conversion Kit#420342

Gloss cycle level button Increase time button

Increase coins button

Displays number ofcoins programmed

Displays number ofminutes programmed

“Lustre King Ball Conditioner Restoration and Conversion Kitsfor Increased Revenues…and Customer Satisfaction”If you have a Lustre KING, that’s either not functioning at itsbest, or not functioning at all, ZOT has the most cost effec-tive solution to both restore the unit, and improve its over-all performance.ZOT’s Lustre KING Restoration and Conversion Kit's make it pos-sible for you to bring the 1970’s price you’ve been charging, intothe New Millennium, and to maximize on revenues during highdemand times, like just before League and Tournament play.

By being able to easily increase the fees by one third, anddecreasing the run timed by 30% you will more than dou-ble your revenues…and improve customer satisfaction atthe same time, since the unit will function so much better.ZOT offers seven Conversion Kits for the Lustre KING thatadd benefits which are more suitable to your everydaybusiness needs.

Coin Mechanism:• Inexpensive yet Rugged Con-

struction, for Quarters** only.• Includes Coin Block Out (for

House Ball Cycle and when the unit is out of Compound).

** Domestic (U.S.) Application. International Applications also available.

Coin Box:• Expanded Coin Capacity (up

to $400 in Quarters).• New Lock and Key.

Top Overlay Panel:• Easy to Install, Drill and Pop

Rivet installation.• Includes new Ball Holder Ring.

Simple to clear jamsand clean

*The Coin Conversion and Cosmetic Kit is designed asan add-on to ZOT’s Control Box Conversion Kit #420342.It will not function as a stand-alone product. This Kit is compatible to all models of Lustre KING, but itis an ‘Essential Requirement’ for earlier models thatpresently have a multi-denomination coin validator.

Contents:Front Panel:

• Front mounted Quick Release Coin Mechanism, making Coin Jams Easy-to-Clear, and the mechanism Easy-to-Clean.

34

7

Ball C

ond

itioner

Prod

ucts

Ball Conditioner Products

Electronic Coin Validator Kit#400202This kit requires #420342 to function. It will not function as a stand-alone product.

• Programmable: to accept a Single Coin as primary payment, and a Promotional Token, for a total polish. (e.g., Quarters, Dollar Coins and Tokens for U.S.)

• Any Denomination and Currency: The Validator can be programmed for a Single Coin of anyDenomination or Currency, up to a maximum size of 34mm in diameter. and 3.4mm thick.(Programmed at ZOT, or by a participating ZOT Distributor).

• Creates New Customers & Greater Profits: The Promotional Tokens are designed to create newBall Conditioner Customers and Greater Profits. A Token Promotion program only needs to devel-op nine new users in a single league season, to pay for Electronic Coin Validator. On a 1,000 Tokenpromotion, that’s less than one percent success rate.

Note:• Machines with ZOT 1 Control Boards will require a P. C. Board upgrade. Contact ZOT for details.• 25 each Free Ball Polish Tokens – Order #400206

The ZOT Programmable Message Display is a Stand-Alone, Add-Onproduct that’s compatible to the Lustre KING and Lustre KLEEN,and many other brands of ball conditioner, including AMF andPerry Austen.Contents:Programmable Message Display, Includes:

• All Mounting Hardware• Power Cord and Plug• Easy-to-Use Remote Control Programmer for Fast and Easy

programming of announcements and message displays.

Scrolling Message Display Kit#400156

ZOT’s Scrolling Message Display replaces the original ‘back-lit’ sign,enabling Easy-to-Program announcements and advertising to bowlers.This attractive electronic Message Center, with its bright scrolling digi-tal display, can be easily programmed to inform your bowlers of forth-coming events (Leagues and Tournaments) honor scores, and the bene-fit of using the unit itself. e.g., “add a high scoring gloss to your ball.”

Side-Door Cosmetic Kit#420349ZOT’s Side-Door Kit completes the conversion ofyour Ball Conditioners cosmetic appearance.Contents:2 Each Side Doors:

• All Welded Steel Construction• Powder Coated, Neutral Color

2 Each ‘T’ Handle & Locks:• Interchanges with Brunswick Parts

Lock Stem & Lock Stem Angle:• Includes all related hardware for conversion.

Lower Support Angle:• New Lower Adjustable Height Angles.• New Bumper Grommets

The Side-Door Kit caneither be used with#420342 and #420348,or as a stand-alone product, which may bepurchased separately.

#400206 BallPolish PromotionTokens

Compound Applicator Gear Assembly#420377**This kit requires ZOT #400182 to function. It will not function as a stand-alone product.

Superior Coumpound Advanced Design: A ZOT Manufactured Gear Assembly, in the style of a LustreKlNG gear assembly, is now available as a retrofit kit for a Lustre KLEEN. ZOT’s More-Positive gear driveCompound Advance system kit solves the Lustre KLEEN’s constant ‘Out-of-Adjustment’ problem.Improved Ball Polish: Results in Improved Customer Satisfaction and makes it possible for you to increasethe price, and reduce the run time, thereby increasing the potential number of users during peak times.Contents:1 Compound Advance Gear Assembly Proven Product: An assembly that’s proven itself on the Lustre

KING. The Gear Assembly that positively advances the entire compound block, without needing constant adjustments. EliminatesWaste: Stop discarding half used compound blocks because a less efficient advance system has resulted in the compound surfacebecoming glazed.

2 Drive System: Includes all Sprocket and Chain assemblies necessary to advance the entire compound block.

35

Ball Conditioner Products

7

Bal

l Co

nd

itio

ner

Pro

duct

s

For all Lustre KING, Lustre KLEEN, AMF Ball Performance Center & Perry Austen Gleam Machines

“If your Ball Conditioner does not really polish balls, the Buffing Wheel may be out of adjustment”

• Easy-To-Adjust: ZOT has designed special nut plates to secure the Bearing Housing and the AlteredPillow Block…thereby eliminating all the securing nuts. Each time you need to advance the buffingwheel (e.g., when replacing a block of compound), simply loosen the six bolts securing the buffingshaft and rotate the added jackscrew. You no longer need to use a wrench on the outside of themachine.

• Buffing Wheel Wear and Use Indication: Calibrations on the ZOT Bracket clearly indicate theamount of adjustment you’ve made and, ultimately, when to install a new buffingwheel.

• Improved Belt Tracking - Eliminates Flat Belt Tracking Problems: ZOT’s Linktype ‘V’ belt system technology provides a more positive power transferfrom the motor to the buffing wheel, than the original flat belt. The ZOTLink style ‘V’ belt system is especially effective in providing a more positivepower transfer as the center to center pulley measurement changes fromthe extreme of a new to an old buffing wheel. And, as the belt wears(stretches) over the years, it’s a simple task to remove a link to increase or reestablish belt tension.

• Positive Wheel/Shaft Secure System: The outside ‘V’ belt pulley on thebuffer shaft features flat surfaces that enable you to attach a wrench, whensecuring the left-hand-threaded jam-nuts, which enables you to easily securethe buffing wheel to the shaft.

Buffer Shaft Conversion Kit#420392Replacements:The “Lustre King” Buffer Shaft Conversion Kit replaces all buffer shafts that utilize a “Balancing Disk”

Easy-Adjust Buffer Kit#420426Replacements:The “Lustre King” Buffer Shaft Conversion Kit #420392 is required to install this kit.

1210

86

42

0

GlossBoss Buffing Compound# 420416 (two blocks per box)

• Same formula that major bowling ball manufacturers use to factory finish new bowling balls

• Designed and formulatedto give a superior polishto all bowling ballcompositions includ-ing: Urethane,Reactive, Particle,Plastic and Rubber.

• Date stamped forshelf-life verification

Buffing Wheel# 820017• Longest lasting buffing

wheel in the industry.

• Superior compound transferto buffing wheel and ball.

• Non-corrosive black powdercoated steel hub.

Note:Always check the condition ofthe spacers when replacing thebuffer wheel.

Lustre King Spacer Kit #420374Lustre Kleen Spacer Kit #420399

36

Ball Conditioner Products

7

Ball C

ond

itioner

Prod

ucts

Buffer Pressure Meter Kit#420455

• The Kit enables youto set and check thepressure (FrictionLevel) between thebuffing wheel andthe bowling ball foroptimal ball polishingperformance.

• The kit comprises an AMP meter that connects to the motor andmeasures the load on the motor during the polishing cycle.

Note:Take the guesswork out of the equation, and replace it with an exactscience.

Ball Conditioner Operations, Service& Parts Explosion Manual#160179• Complete Operations, Adjustments, Service

and Parts Breakdown.

• For ZOT GlossBoss, Brunswick BallWorx andmany parts for Lustre King & Lustre Kleen.

Urethane Brake Roller#810053

• Urethane Brake Rollers are moredurable than rubber rollers.

• Oil Resistant: ZOT’s UrethaneBrake Rollers prevent readjust-ments necessary when rubberrollers become saturated with oiland swell.

Urethane Cradle Roller#420381

Note:• Order 4 rollers per machine• Bronze Bearing included

Micro Switch (Wiper style)#300031

Micro Switch (Bearing style)#300032

Coin MechanismLustre King (Quarters Only)#800063

Lustre Kleen, AMF/Century, Perry Austen#800073

Direct Replacement for Original Equipment

Printed Circuit Board Kit#400182

For Brunswick Lustre Kleen,AMF/Century and Perry Austen

A complete replacement for an orig-inal PC Board with many added fea-tures and benefits, including:

• Easy to Program Price Levels

• Add Bill Acceptor

• Add Gear Style CompoundApplicator

Note:Includes circuit to plug-in and run a Bill Acceptor & LCD Price Display.

Air Filter#820015New and/or clean air filters ensureoptimal ventilation for better orimproved machine performance.

T-Handle Lock Assembly with Key#LK-A16(for Lustre Kleen only)

#420444Universal - for all other machines

Note:Zot recommends replacing air filtersas necessary,but at least every six-months.

Motor#200011220/110V-50/60Hz – 1HP

• Replaces all previous originalmotors except for GE Motors withexternally box mounted capacitors(AKA Short Motor – call for details).

Capacitors#211216

Urethane Oscillator Bumper Kit#420415• All the durability of a Urethane

for a much longer life than rub-ber products

Note:Order 2-Kits per machine

Lustre Kleen Buffer Shaft#520136

• Direct Replacement for Lustre Kleen

• To Convert a Lustre King to a Double Bearing Support, order Kit #420392