7/28/2019 CEI 2-26 V1 EN 60034-18-21_A1_A2 1997 Fasc. 4071 - (en + it).pdf
1/14
Norma Italian a
N O R M A I T A L I A N A C E I
CNR CONSIGLIO NAZIONALE DELLE RICERCHE AEI ASSOCIAZIONE ELETTROTECNICA ED ELETTRONICA ITALIANA
Data Pubblicazione
Classi ficazione Fascicolo
COMITATO
ELETTROTECNICO
ITALIANO
Titolo
Title
CEI EN 60034-18-21/A1/A2
1997-12
2-26;V1 4071
Macchine elettriche rotanti
Parte 18: Valutazione funzionale dei sistemi di isolamento
Sezione 21: Procedure di prova per avvolgimenti a filo - Valutazione termica eclassificazione
Rotating electrical machines
Part 18: Functional evaluation of insulation systemsSection 21: Test procedures for wire-wound windings - Thermal evaluation and classification
APPARECCHIATURE ELETTRICHE PER SISTEMI DI ENERGIA E PER TRAZIONE
VARIANTE
NORM
A
TE
CNICA
7/28/2019 CEI 2-26 V1 EN 60034-18-21_A1_A2 1997 Fasc. 4071 - (en + it).pdf
2/14
CEI - M ilano 1997. R iproduzione vietata.
Tutti i diritti sono riservati. Nessuna parte del presente Documento pu essere riprodotta o diffusa con un mezzo qualsiasi senza il consenso scritto del CEI.Le Norme CEI sono revisionate, quando necessario, con la pubblicazione sia di nuove edizioni sia di varianti. importante pertanto che gli utenti delle stesse si accertino di essere in possesso dellultima edizione o variante.
SOMMARIO
Vale il sommario della Norma base.
DESCRITTORI
DESCRIPTORS
Macchine elettriche rotanti
Rotating electrical machine;Isolamento elettrico
Electrical insulation;Provaavvolgimenti
Winding;Prova
Test;Prova di durata termica
Thermal endurance test;Classificazione
Classification;
COLLEGAMENTI/RELAZIONI TRA DOCUMENTI
Nazionali
Europei
(IDT) EN 60034-18-21/A1:1996-12; EN 60034-18-21/A2:1996-12;
Internazionali
(IDT) IEC 34-18-21/A1:1994-11; IEC 34-18-21/A2:1996-11;
Legislativi
INFORMAZIONI EDITORIALI
Norma Italian a
CEI EN 60034-18-21/A1/A2
Pubblicazione
Variante
Carat tere Doc.
Stato Edizi one
In vigore
Data validit
1998-2-1
Ambito validit
EuropeoVarianti
Nessuna
Ed. Prec. Fasc.
Nessuna
Comita to Tecnico
2-Macchine rotanti
Approvata dal
Presidente del CEI
in Data
1997-12-16
CENELEC
in Data
1996-10-1
Sottoposta a
inchiesta pubblica come Documento originale
Chiusa in data
1996-8-15
Gru ppo Abb.
3
Sezioni Abb.
B
Prezzo Norm a IEC
32 SFr
ICS
29.080.00; 29.160.00;CDU
621.313:621.315.6:620.1:621.317.08
LEGENDA
(IDT) La Norma in oggetto identica alle Norme indicate dopo il riferimento (IDT)
7/28/2019 CEI 2-26 V1 EN 60034-18-21_A1_A2 1997 Fasc. 4071 - (en + it).pdf
3/14
CEN ELEC members are bound to comply wi th the
CEN/CENELEC Internal Regulations which stipulate
the conditions for giving this European Standard the
status of a National Standard without any alteration.
Up-to-date lists and bi bli ographical references con-
cerning such National Standards may be obtained on
application to the Central Secretariat or to any
CENELEC member.
This European Standard exi sts in three offi cial ver-
sions ( English, French, G erman).
A version in any other language and notified to the
CEN ELEC C entral Secretariat has the same status as
the official versions.
CENELEC members are the national electrotechnical
committees of: A ustria, Belgium, D enmark, Finland,
France, G ermany, G reece, I celand, Ireland, Italy, Lu-
xembourg, N etherlands, N orway, Portugal, Spain,
Sweden, Switzerland and Uni ted K ingdom.
I Comi tati N azionali membri del CENELEC sono tenu-
ti, in accordo col regolamento interno del CEN/CENE-
LEC, ad adottare questa Norma Europea, senza alcuna
modifica, come Norma Nazionale.
G li elenchi aggiornati e i relativi riferimenti di tali Nor-
me Nazionali possono essere ottenuti rivolgendosi al
Segretario Centrale del CENELEC o agli uffici di qual-
siasi Comitato Nazionale membro.
La presente Norma Europea esiste in tre versioni uffi -
ciali ( inglese, francese, tedesco).
Una traduzione effettuata da un altro Paese membro,
sotto la sua responsabilit, nella sua lingua nazionale
e notificata al CENELEC, ha la medesima validit.
I membri del CEN ELEC sono i Comi tati Elettrotecnici
Nazionali dei seguenti Paesi: Austria, Belgio, D ani-
marca, Finlandia, Francia, G ermania, G recia, I rlanda,
Islanda, I talia, Lussemburgo, N orvegia, O landa, Por-
togallo, Regno Unito, Spagna, Svezia e Svizzera.
CENELEC Copyright reserved to all CENELEC members. I diritti di riproduzione di questa Norma Europea sono riservati esclu-sivamente ai membri nazionali del CENELEC.
Comitato Europeo di Normalizzazione Elettrotecnica
European Committee for Electrotechnical Standardization
Comit Europen de Normalisation Electrotechnique
Europisches Komitee fr Elektrotechnische Normung
C E N E L E C
Secrtariat Central:
rue de Stassart 35, B - 1050 Bruxelles
Europische Norm Norme Europenne European Standard Norma Europea
EN 60034-18-21/A1:1996-12 + EN 60034-18-21/A2:1996-12
Macchine elettriche rotanti
Parte 18: Valutazione funzionale dei sistemi di isolamento
Sezione 21: Procedure di prova per avvolgimenti a filo - Valutazione termica eclassificazione
Rotating electrical machines
Part 18: Functional evaluation of insulation systemsSection 21: Test procedures for wire-wound windings - Thermal evaluation and classification
Machines lectriques tournantes
Partie 18: Evaluation fonctionnelle des systmes disolation
Section 21: Procdures dessai pour enroulements fils - Evaluation thermique etclassification
Drehende elektrische Maschinen
Teil 18: Funktionelle Bewertung von Isoliersystemen fr drehende elektrischeMaschinen
Hauptabschnitt 21: Prfverfahren fr Runddraht-Wicklungen - Thermische Bewertung und
Klassifizierung
7/28/2019 CEI 2-26 V1 EN 60034-18-21_A1_A2 1997 Fasc. 4071 - (en + it).pdf
4/14
NORMA TECNICA
CEI EN 60034-18-21/A1/A2:1997-12
Pagina iv
FOREWORD TO AMENDMENT A1
T he text of A mendment 1:1994 to the Interna-
tional Standard IEC 34-18-21:1992, prepared by
SC 2J, Classification of insulation systems for ro-
tating machinery, of IEC T C 2, Rotating machin-
ery, was submitted to the formal vote and was
approved by CEN ELEC as Amendment A1 to
EN 60034-18-21:1994 on 1996/10/01 without
any modification.
T he following dates were fixed:
latest date by which the amendment has to
be implemented at national level by publi-
cation of an identical national standard or
by endorsement
(dop) 1997/09/01
latest date by which the national standards
conflicting with the amendment have to be
withdrawn
(dow) 1997/09/01
For products which have complied withEN 60034-18-21:1994 before 1997/09/01, as
shown by the manufacturer or by a certifi cation
body, this previous Standard may continue to
apply for production until 2002/09/01.
ENDORSEMENT NOTICE
T he text of amendment 1:1994 to the Interna-
tional Standard I EC 34-18-21:1992 was ap-
proved by CEN ELEC as an amendment to the
European Standard without any modifi cation.
WARNING
T he text of Amendment A1 is poi nted out by a
vertical line.
PREFAZIONE ALLA MODIFICA A1
I l testo della M odifica l:1994 alla Pubblicazione
IEC 34-18-21:1992, preparato dal SC 2J, C lassifica-
zione dei sistemi isolanti per macchine elettriche
rotanti del T C 2 della IEC, M acchine Elettriche Ro-
tanti, stato sottoposto al voto formale ed stato
approvato dal CEN ELEC come M odifica A1 alla
EN 60034-18-21:1994 in data 01/10/1996 senza al-
cuna modifi ca .
Sono state fissate le seguenti date
data ultima entro la quale la modifi ca deve es-
sere applicata a livello nazionale mediante
pubblicazione di una Norma nazionale identi-
ca o mediante adozione
(dop) 01/09/1997
data ultima entro la quale le Norme nazionali
contrastanti con la modifi ca devono essere ri-
tirate
(dow) 01/09/1997
Per i prodotti che erano conformi allaEN 60034-18-21:1994 pri ma del 01/09/1997, come
indicato dal costruttore o da un O rganismo di
Certificazione, la Norma precedente pu conti-
nuare ad essere applicata per la produzione fi no
al 01/09/2002.
AVVISO DI ADOZIONE
I l testo della M odifica 1:1994 alla Pubbli cazione
Internazionale I EC 34-18-21:1992 stato approva-
to dal CEN ELEC come una modifica alla Norma
Europea senza alcuna variante.
AVVERTENZA
I l testo della M odifica A1 evidenziato da una
barra verticale a margine.
RIPRODUZIONE SU LICENZA CEI AD ESCLUSIVO USO
AZIENDALE
7/28/2019 CEI 2-26 V1 EN 60034-18-21_A1_A2 1997 Fasc. 4071 - (en + it).pdf
5/14
NORMA TECNICA
CEI EN 60034-18-21/A1/A2:1997-12
Pagina v
FOREWORD TO AMENDMENT A2
T he text of document 2J/51/FD IS, future
amendment 2 to I EC 34-18-21:1992, prepared
by SC 2J, Classifi cation of insulation systems for
rotating machinery, of IEC T C 2, Rotating ma-
chinery, was submi tted to the IEC-CENELEC
parallel vote and was approved by CEN ELEC as
Amendment A2 to EN 60034-18-21:1994 on
1996/10/01.
T he followi ng dates were fixed:
latest date by which the amendment has to
be implemented at national level by publi-
cation of an identical national standard or
by endorsement
(dop) 1997/09/01
latest date by which the national standards
conflicting with the amendment have to be
withdrawn
(dow) 1997/09/01
For products which have complied withEN 60034-18-21:1994 and its amendment
A1:1996 before 1997/09/01, as shown by the
manufacturer or by a certifi cation body, this
previous Standard may continue to apply for
production until 2002/09/01.
ENDORSEMENT NOTICE
T he text of amendment 2:1996 to the Interna-
tional Standard I EC 34-18-21:1992 was ap-
proved by CEN ELEC as an amendment to the
European Standard wi thout any modifi cation.
PREMESSA ALLA MODIFICA A2
I l testo del documento 2J\ 51\ FD IS, futura M odifi-
ca 2 alla Pubblicazione I EC 34-18-21:1992, prepa-
rato dal SC 2J, Classifi cazione dei sistemi isolanti
per macchine elettriche rotanti , del T C 2 della
IEC, M acchine elettriche rotanti, stato sottoposto
al voto parallelo IEC-CENELEC ed stato appro-
vato dal CEN ELEC come M odifi ca A2 alla
EN 60034-18-21:1994 in data 01/10/1996
Sono state fi ssate le seguenti date:
data ultima entro la quale la modifica deve es-
sere applicata a livello nazionale mediante
pubblicazione di una Norma nazionale identi-
ca o mediante adozione
(dop) 01/09/1997
data ultima entro la quale le Norme nazionali
contrastanti con la modifica devono essere ri-
tirate
(dow) 01/09/1997
Per i prodotti che si sono uniformati allaEN 60034-18-21:1992 e alla sua M odifi ca A1:1996
prima del 01/09/1997, come dimostrato dal cos-
truttore o da un ente di certifi cazione, questa nor-
ma precedente pu continuare ad essere appli ca-
ta per la produzione fi no al 01/09/2002.
AVVISO DI ADOZIONE
I l testo della modifi ca 2:1996 della Norma I nterna-
zionale IEC 34-18-21:1992 stato approvato dal
CEN ELEC come modifica alla Norma Europea
senza alcuna variante.
RIPRODUZIONE SU LICENZA CEI AD ESCLUSIVO USO
AZIENDALE
7/28/2019 CEI 2-26 V1 EN 60034-18-21_A1_A2 1997 Fasc. 4071 - (en + it).pdf
6/14
NORMA TECNICA
CEI EN 60034-18-21/A1/A2:1997-12
Pagina vi
RIPRODUZIONE SU LICENZA CEI AD ESCLUSIVO USO
AZIENDALE
7/28/2019 CEI 2-26 V1 EN 60034-18-21_A1_A2 1997 Fasc. 4071 - (en + it).pdf
7/14
NORMA TECNICA
CEI EN 60034-18-21/A1/A2:1997-12
Pagina 1 di 8
3.2
Standard procedures
Replace the text of this subclause by the following:
Five standard procedures are specifi ed in claus-es 4 through 8. Procedure 1 can be considered
of general applicability to both a.c. and d.c. ap-
plications and to both stators and armatures.
H owever, the user of this standard may select
that test procedure which most closely corre-
sponds to the type and size of the windings to
be tested and classifi ed, tak ing into account fa-
cilities and past experience.
3.4.1
Construction of test objects
Replace the text of the note by the following:
Nota/Note
It i s recognized that markedly di fferent valu es of test li fe canbe obtain ed for the same in sul ati ng ma terial s, dependi ng onin sul ati on thi cknesses an d creepage distances.
3.7
Ageing temperature and subcycle lengths
Replace the fourth paragraph by the following:
Ageing temperatures and lengths of ageing sub-
cycles should be selected from Tab. 2 of
Section 1.
Replace the seventh paragraph by the following:
I n addition, at least two higher ageing tempera-
tures should be selected, separated by intervals
of 20 K or more. I ntervals of 10 K may be used
when tests are made at more than three ageing
temperatures.
4.1.1
Procedure 1
Replace the existing text by the following:
T his procedure, using motorette type models
as test objects, shall be referred to as
IEC 34-18-21, Procedure 1.
5.1.1
Procedure 2
Replace the existing text by the following:
T his procedure, using actual motors as test ob-
jects, shall be referred to as IEC 34-18-21, Proce-
dure 2.
5.1.2
General features
Replace the fourth paragraph by the following:
Even though actual motors are tested, the re-sults may not be used to determine endurance
VARIANTE ALLA CEI EN 60034-18-21 (CEI 2-26)
Procedure normalizzate
Sostituire il testo di questo sottoparagrafo come segue:
Negli A rticoli da 4 ad 8 sono specificate 5 procedu-re normalizzate. La procedura 1 pu essere consi-
derata di applicabilit generale sia alla c.a. che alla
c.c. e sia agli statori che alle armature. Tuttavia
lutilizzatore della presente Norma pu scegliere
quella procedura di prova che pi strettamente
corrisponde al tipo ed alla taglia degli avvolgimenti
che debbono essere provati e classificati, tenendo
conto delle attrezzature e dellesperienza acquisita.
Costruzione degli oggetti di prova
Nel testo della nota la correzione riguarda il solo testo
inglese.
Temperature di invecchiamento e durata deisottocicli
Sostituire il quarto capoverso come segue:
Le temperature di invecchiamento e le durate dei
sottocicli dovrebbero essere scelti dalla T ab. 2
della Sezione 1.
Sostituire il settimo capoverso come segue:
In aggiunta si dovrebbero scegliere almeno due
temperature di invecchiamento pi alte , separate
da intervalli di almeno 20 K o pi. Si possono uti-
lizzare intervalli di 10 K quando le prove vengono
effettuate a pi di tre temperature di invecchia-
mento.
Procedura 1
Sostituire il testo esistente come segue:
Q uesta procedura, che utili zza come oggetti di
prova modelli tipo motoretta, deve essere iden-
tificata come Procedura 1 della I EC 34-18-21.
Procedura 2
Sostituire il testo esistente come segue:
Q uesta procedura, che utili zza come oggetti di
prova motori reali deve essere identifi cata come
Procedura 2 della IEC 34-18-21.
Caratteristiche generali
Nel quarto capoverso la correzione riguarda il solo te-sto inglese.
CEI EN 60034-18-21/A1/A 2:1997-12
14
RIPRODUZIONE SU LICENZA CEI AD ESCLUSIVO USO
AZIENDALE
7/28/2019 CEI 2-26 V1 EN 60034-18-21_A1_A2 1997 Fasc. 4071 - (en + it).pdf
8/14
NORMA TECNICA
CEI EN 60034-18-21/A1/A2:1997-12
Pagina 2 di 8
Me zzi di riscaldamento
Nel primo capoverso la correzione riguarda il solo te-sto inglese.
Sostituire il terzo capoverso come segue:
I motori monofasi devono essere sottoposti ad al-
meno 250 operazioni di avviamento e fermata per
ogni giorno della parte del ciclo di invecchiamen-
to termico. D urante lavviamento lavvolgimento
di avviamento di un motore monofase normal-
mente funziona con una densit di corrente moltopi elevata dellavvolgimento principale. D urante
ogni avviamento esso pu raggiungere una tem-
peratura da 10 K a 30 K pi elevata di quella
dellavvolgimento principale. A l fi ne di assicurarsi
che la corretta attenzione venga posta sulla parte
del sistema di isolamento riguardante lavvolgi-
mento principale, si dovrebbe effettuare un nu-
mero ragionevole di avviamenti.
Nel quarto capoverso la correzione riguarda il solo te-sto inglese.
time in actual service in an absolute sense. T he
tests may be used as a means of classifi cation
only by comparing insulation systems.
5.3.2
Me ans of heating
Replace the first paragraph by the following:
T he mode of heat generation is dictated by thetype of motor being used in the test and the
laboratory equipment available. H igher than
normal winding temperatures can be obtained
by increasing motor losses by such means as
enlarging the air gap, starting and reversing
each motor, superimposition of direct current
on the normal alternating current, or by increas-
ing the temperature of the air surrounding the
motor. For temperature regulation during the
heat ageing portion of the cycle, the motors
may be run at normal voltage and frequency
with an electrical control which automatically
starts and stops or reverses the di rection of rota-
tion of the motors at intervals. O ther acceptable
means of temperature control include automatic
voltage variation, adjustment of the surrounding
air temperature, or combinations thereof.
Replace the third paragraph by the following:
Single-phase motors shall have at least 250
start-stop operations each day of the heat age-
ing portion of the cycle. T he starting winding of
a single-phase motor normally operates at a
much higher current density than the main
winding during starting. D uring each start it canreach a temperature of 10 K to 30 K higher than
the main winding. I n order to ensure that the
correct emphasis is placed on the main winding
portion of the insulation system, a reasonable
number of starts should be employed.
Replace the fourth paragraph by the following:
Polyphase motors shall have at least 1000 starts
or reversals each day of the heat ageing portionof the cycle. O ften the electrical loss during re-
versal is used to maintain the elevated tempera-
tures, in which case the number of reversals
may greatly exceed 1000 per day. At the highest
temperature test the total time of exposure is
relatively short which results in a relatively low
number of reversals during the life of the test.
At the lowest temperature, the time of exposure
can be 16 to 20 times as long as that of the
highest level. A wide variation in total number
of starts would affect the slope of the time-tem-
perature curve wi thin a cycle. T hus, i t is recom-mended that the number of reversals at the low
temperature be no greater than twice those at
RIPRODUZIONE SU LICENZA CEI AD ESCLUSIVO USO
AZIENDALE
7/28/2019 CEI 2-26 V1 EN 60034-18-21_A1_A2 1997 Fasc. 4071 - (en + it).pdf
9/14
NORMA TECNICA
CEI EN 60034-18-21/A1/A2:1997-12
Pagina 3 di 8
Sollecitazioni m eccaniche durante il sottociclo diinvecchiamento termico
Nel primo capoverso la correzione riguarda il solo te-sto inglese.
Prova di umidit
Nel primo capoverso la correzione riguarda il solo te-sto inglese.
Nel secondo capoverso la correzione riguarda il solotesto inglese.
Prova di tensione
Nel secondo capoverso la correzione riguarda il solotesto inglese.
the high temperature. I deally, an equal number
of reversals at each temperature should be
sought.
5.3.4 Mechanical stresses during the thermal ageingsubcycle
Replace the first paragraph by the following:
M echanical stress is obtained in tests on actual
motors by the normal vibration of the motor
running and with starts or reversals, or both.
T here is mechanical shock from starting or re-
versing. T he vibration amplitude at twice the
line frequency can be increased by enlarging
the air gap. Larger forces are present in the
windings as a result of the high currents during
starting and reversing of the motors. In a test,
these mechanical forces occur at elevated tem-
peratures.
5.4.1 Moisture test
Replace the first paragraph by the following:
A moisture test of at least 48 h shall be used,
except that for totally enclosed machines ( de-
grees of protection I P44 or more) and for d.c.
machines a moisture test is not mandatory be-
cause it can be impracticable. M oisture shall be
visible on the windings as droplets, without
puddles, during the moisture test. T o ensure
visible condensation, the insulation system
should be at a lower temperature than the dew
point of the surrounding moisture-laden atmos-
phere at all times. T he preferred method of
meeting this requirement is by the use of a con-
densation test chamber with cooled test objects
described in clause C.2 of annex C.
Replace the second paragraph by the following:
H owever, larger motors can be diffi cult to move
and difficult to support in equipment for moi s-
ture test, or such equipment is not available.
O ther methods of applying moi sture include:
placing an enclosing hood around the motor, orusing a conventional humidity cabinet or a fog
chamber.
5.4.2 Voltage test
Replace the second paragraph by the following:
T he motors should be started and run immedi-
ately after the moisture test while the windings
are still wet. For machines that have to be reas-
sembled prior to running, a power-frequency
high potential test should be applied at the
highest rated voltage from windings to framefor 10 min whi le wet before assembly. D uring
RIPRODUZIONE SU LICENZA CEI AD ESCLUSIVO USO
AZIENDALE
7/28/2019 CEI 2-26 V1 EN 60034-18-21_A1_A2 1997 Fasc. 4071 - (en + it).pdf
10/14
7/28/2019 CEI 2-26 V1 EN 60034-18-21_A1_A2 1997 Fasc. 4071 - (en + it).pdf
11/14
NORMA TECNICA
CEI EN 60034-18-21/A1/A2:1997-12
Pagina 5 di 8
Pu essere anche richiesta una protezione della
superfi cie del commutatore e delle connessioni
nude.
Numero dei campioni
Sostituire il testo esistente come segue:
Per ogni sistema di isolamento si dovrebbero pro-
vare ad ogni temperatura di invecchiamento al-
meno 10 campioni di prova. Un rotore pu essere
avvolto in modo da comprendere pi di un siste-
ma di isolamento, ciascuno adeguatamente identi-
ficato ed isolato. Preferibilmente si dovrebbero
avvolgere pi rotori, ciascuno con un diverso si-
stema di isolamento per una prova a ciascuna
temperatura di invecchiamento .
Dettagli costruttivi delle motorette (esempio)
Nel primo capoverso la correzione riguarda il solo te-sto inglese.
Nel terzo capoverso la correzione riguarda il solo testoinglese.
flashover or undue burning of insulations dur-
ing overvoltage testing. To alleviate this condi-
tion, excess moisture on the commutator from
humidifi cation may be removed by carefully di-
rected forced air or wiping prior to application
of voltage. Enclosure of the commutator surface
and bare connections can also be required.
8.2.2 Number of test specimens
Replace the existing text by the following:
At least 10 test specimens of each insulati on
system should be tested at each ageing temper-
ature. A rotor may be wound to i ncorporate
more than one insulation system, each ade-
quately identifi ed and isolated. Preferably, sev-
eral rotors each containing a different insulation
system should be wound for test at each ageing
temperature.
A.2 Detail ed m otorette construction (example )
Replace the first paragraph by the following:
I n a laboratory where modifi cations to a pre-
scribed motorette assembly can be made to i m-
prove or more conveniently achieve a test ob-
jective, the detailed information in this annex
can be unnecessary. H owever, if extensive ex-
perience in insulation evaluation is unavailable
or if any attempt is to be made to compare test
data between laboratories, the motorette con-struction described here is to be followed me-
ticulously. Experience has shown that only the
greatest care in the design and preparation of a
motorette will result in specimens which can be
tested in different laboratories with results that
are comparable.
Replace the third paragraph by the following:
T he finished motorette consists of a rigid sup-
porting metal base with four suitable stand-off
insulators of porcelain or other appropriate ma-
terial bolted to one end and with two slots,
formed by an inner and outer sheet, bolted to
the other end. T he supporting base has holes
for mounting the motorette during vibration
testing. T he slot selections are fabricated from
stainless steel sheets. T he assembled slot por-
tion contains two coils insulated from the frame
by slot insulation, insulated from each other by
phase insulation and held in place by slot
wedges. T hese components are typi cal parts as
used in actual motors. T he coi ls are each
wound with parallel wires so that conduc-
tor-to-conductor electrical tests can be made.T hey can be machine-wound on pins or forms,
RIPRODUZIONE SU LICENZA CEI AD ESCLUSIVO USO
AZIENDALE
7/28/2019 CEI 2-26 V1 EN 60034-18-21_A1_A2 1997 Fasc. 4071 - (en + it).pdf
12/14
NORMA TECNICA
CEI EN 60034-18-21/A1/A2:1997-12
Pagina 6 di 8
Attrezzature di prova per bobine di cam po in filoavvolte in modo non uniforme per macchine acorrente continua
Nel primo capoverso la correzione riguarda il solo te-sto inglese.
Sostituire il terzo capoverso come segue:
Si dovrebbe considerare che i campioni di prova
sono modelli per i quali pu essere impossibile
simulare linfluenza dei processi di costruzione
( per esempio lavvolgimento diretto).
Attrezzature di prova per bobine di cam po in filoavvolte a strati uniformi per macchine acorrente continua
Nel secondo capoverso la correzione riguarda il solotesto inglese.
as in ordinary shop practice. When appropriate,
the construction and processing procedures
may be modified to simulate the intended use.
T he followi ng is a detailed description of the
preparation of motorettes. I t is presented as an
example for construction for the purpose of this
standard.
B.1 Test fixture for random wire-wound field coilsfor d.c. machines
Replace the first paragraph by the following:
D etails of the construction of a test fixture for
the evaluation of the insulation system of a ran-
dom-wound fi eld coi l are shown, as an exam-
ple only, in figures 4 to 7. T he detailed informa-
tion can be unnecessary for a laboratory
developing its own test objects. H owever, for
laboratories without extensive testing experi-ence, or if comparisons are to be made be-
tween laboratories, the minute details shall be
observed and followed meticulously. M odifica-
tions of dimensions or of design may be made
to allow manufacturers to simulate more closely
their own fi eld coil structures or designs.
Replace the third paragraph by the following:
I t should be appreciated that the test specimens
are models on which it can be impossible to
simulate the influence of manufacturing proc-
esses (e.g. di rect winding) .
B.2 Test fixture for precision wire-wound fieldcoils for d.c. machines
Replace the second paragraph by the following:
Actual poles may be used, if convenient, and
can be desirable if techniques for holding the
coils to poles depend on the rigidity of the pole
structure. H eavier steel may also be used for the
frame plate for similar reasons.
Fin e Documen to
RIPRODUZIONE SU LICENZA CEI AD ESCLUSIVO USO
AZIENDALE
7/28/2019 CEI 2-26 V1 EN 60034-18-21_A1_A2 1997 Fasc. 4071 - (en + it).pdf
13/14
NORMA TECNICA
CEI EN 60034-18-21/A1/A2:1997-12
Pagina 7 di 8
RIPRODUZIONE SU LICENZA CEI AD ESCLUSIVO USO
AZIENDALE
7/28/2019 CEI 2-26 V1 EN 60034-18-21_A1_A2 1997 Fasc. 4071 - (en + it).pdf
14/14
NORMA TECNICA
CEI EN 60034-18-21/A1/A2:1997-12
La presente Norma stata compilata dal Comitato Elettrotecnico I taliano
e beneficia del riconoscimento di cui alla legge 1 M arzo 1968, n. 186.
Editore CEI , Comitato Elettrotecnico Italiano, M ilano - Stampa in proprio
Autorizzazione del Tribunale di M ilano N. 4093 del 24 luglio 1956
Responsabile:Ing. E. Camagni
Sede del Punto di Vendita e di Consultazione
20126 M ilano - Viale Monza, 261
Lire 25.000
2 Ma cchine rotanti
CEI EN 60034-1 (CEI 2-3)Macchine elettriche rotanti Parte 1: Caratteristiche nominali edi funzionamento
CEI 2- 5Macchine sincrone trifasi - Determinazione sperimentale dellegrandezze
CEI 2- 6Macchine elettriche rotanti - Metodi di determinazione, me-diante prove, delle perdite e del rendimento
CEI EN 60034-6 (CEI 2-7)Macchine elettriche rotanti Parte 6: Metodi di raffreddamento(Codice IC)
CEI 2- 8Macchine elettriche rotanti - Parte 8: Marcatura dei terminali e
senso di rotazione delle macchine rotanti
CEI 2- 9Macchine con tensione nominale compresa fra 5 e 24 kV - Pro-ve di isolamento delle barre e delle matasse
CEI 2-10Macchine elettriche - Metodi di prova per la misura delle carat-teristiche fisiche dei materiali delle spazzole
CEI 2-13Macchine elettriche rotanti - Misura delle perdite con il metodocalorimetrico
CEI EN 60034-7 (CEI 2-14)Macchine elettriche rotanti Parte 7: Classificazione delle formecostruttive e dei tipi di installazione
CEI EN 6003 4-12 (CEI 2-15)Macchine elettriche rotanti Parte 12: Caratteristiche di avvia-mento dei motori asincroni trifase a gabbia, ad una sola velo-cit, a 50 Hz e per tensioni di alimentazione inferiori o uguali a690 V
CEI EN 60034-5 (CEI 2-16)Classificazione dei gradi di protezione degli involucri dellemacchine elettriche rotanti
CEI 2-17Macchine elettriche rotanti Parte 15: Livelli di tensione di tenu-ta ad impulso delle macchine rotanti a corrente alternata conbobine statoriche preformate.
CEI 2-18Guida per limpiego e lesercizio di macchine sincrone a rotore
liscio raffreddate in idrogenoCEI 2-19Dimensioni delle spazzole e dei portaspazzole per macchineelettriche
CEI EN 60276 (CEI 2-20)Definizioni e nomenclatura per spazzole di carbone, portaspaz-zole, commutatori e collettori ad anello
CEI EN 60034-1 6-1 (CEI 2-21)Macchine elettriche rotanti Parte 16: Sistemi di eccitazione permacchine sincrone. Capitolo 1: Definizioni.
CEI EN 60034-3 (CEI 2-22)Macchine elettriche rotanti Parte 3: Prescrizioni specifiche permacchine sincrone a rotore liscio (turboalternatori)
CEI 2-23Macchine elettriche rotanti Parte 14: Vibrazioni meccaniche dimacchine con altezza dasse uguale o superiore a 56 mm. Mi-sura, valutazione e limiti della intensit di vibrazione
CEI EN 60034-9 (CEI 2-24)Macchine elettriche rotanti Parte 9: Limiti di rumore
CEI EN 60034-1 8-1 (CEI 2-25)Macchine elettriche rotanti Parte 18: Valutazione funzionaledei sistemi di isolamento Sezione 1: Principi direttivi generali
CEI EN 60034-1 8-21 (CEI 2-26)Macchine elettriche rotanti Parte 18: Valutazione funzionaledei sistemi di isolamento Sezione 21: Procedure di prova peravvolgimenti a filo Valutazione termica e classificazione
CEI EN 60034-1 8-31 (CEI 2-27)
Macchine elettriche rotanti Parte 18: Valutazione funzionaledei sistemi di isolamento Sezione 31: Procedure di prova peravvolgimenti preformati Valutazione termica e classificazio-ne di sistemi di isolamento utilizzati in macchine fino a 50 MVAe 15 kV, estremi inclusi
CEI EN 6003 4-22 (CEI 2-28)Macchine elettriche rotanti Parte 22: Generatori a corrente al-ternata per gruppi elettrogeni azionati da motori a combustio-ne interna a pistoni