8/14/2019 Fujitsu P1610 IO Board Modem
1/7
LifeBook P1610IO Board and Modem
ReplacementESD Prec autions a re req uired when wo rking on this LifeBoo k co mp uter.Ma ke sure the LifeBoo k is turned off b efo re beg inning this p roc ed ure.
1. Turn the LifeBook over and
remo ve the b attery
3. Release the c ab le by flipp ing the
latc h up.
2. Extrac t these 3 sc rews from the
Hard Disk Drive c over and lift it off.
4. Lift the Drive out.
8/14/2019 Fujitsu P1610 IO Board Modem
2/7
5. Extrac t 11 sc rews from the low er
case.
7. Op en the LifeBoo k and lay it fla t.
9. Lift the top ed ge of the keybo ard
up a nd turn it over
11. Tilt the Disp lay up a nd rota te it
turn.
6. Extrac t 2 sc rews from the rea r of
the LifeBook.
8. Use a p lastic p ry too l to remove
the keyboa rd up pe r trim.
10. Disc onnec t the keybo a rd a nd
ClickPoint c ab les from the system
bo ard b y pulling them ge ntly.
12. Slide out the lowe r hinge c ove r.
8/14/2019 Fujitsu P1610 IO Board Modem
3/7
13. Turn the Disp lay bac k and lay it
down.
15. Extrac t 2 sc rews from the Disp lay
hinge.
17. Extrac t 4 sc rews from the up per
c ase and o pen the external VGA
co nnector cover.
19. Lift off the upper c ase.
14. Disc onnec t 2 Disp lay cab les from
the system bo ard a nd the 2 antenna
c ab les from the WLAN Card .
16. Lift the Disp lay off the lowe r
assembly.
18. Disc onne c t the Clic kPoint butto n
c ab le a nd the spe aker c ab le from
the system boa rd .
20. Extrac t 2 hex sc rews from the
external VGA c onnec tor.
8/14/2019 Fujitsu P1610 IO Board Modem
4/7
21. Disc onne c t the IO Boa rd ribbon
ca ble and the Bluetooth a ntenna
cable. -2762_close
23. Turn the IO Boa rd over, extrac t 2
sc rew s from the m od em and lift it off.
25. Insert the IO Boa rd into the lowe r
c ase a nd sec ure it with 4 sc rew s.
27. Insert 2 hex sc rews into the
external VGA c onnec tor.
22. Extrac t 4 sc rews from the IO
Boa rd and lift it and the RJ11
c onnec tor out of the low er c ase.
24. Transfer the c onnec to r to the
new Mod em , press it onto the new
IO Boa rd a nd sec ure it with 2 sc rew s.
26. Connec t the IO Boa rd ribbon
ca ble and the Bluetooth a ntenna
cable.
28. Plac e the upp er c ase and
c onnec t the Clic kPoint button c ab le
and the spe aker c ab le.
8/14/2019 Fujitsu P1610 IO Board Modem
5/7
29. Close the external VGA
co nnector co ver and sec ure the
upper case with 4 screws.
31. Sec ure the d isp lay with 2 sc rews
in the hinge .
33. Tilt the d isp lay up a nd rota te it
turn.
35. Turn the Disp lay bac k and lay it
down.
30. Extrac t 3 sc rews from the PCB.
32. Atta c h the 2 disp lay c ab les to
the system bo ard a nd the 2 antenna
Ca b les to the WLAN ca rd .
34. Slide the low er hinge c over into
place.
36. Plug in the c ab les for the
keyboa rd and Clic kPoint.
8/14/2019 Fujitsu P1610 IO Board Modem
6/7
37. Turn the keyb oard ove r and slide
it into p lac e
39. Close the LifeBoo k and turn it
over.
41. Insert 11 sc rews into the lower
case.
43. Press the la tc h do wn to loc k the
ca ble into place.
38. Press the keyboard upper trim
into place .
40. Insert 2 sc rews into the rea r of
the LifeBook.
42. Insert the Hard Drive.
44. Rep lac e the Drive cove r and
sec ure it w ith 3 sc rews.
8/14/2019 Fujitsu P1610 IO Board Modem
7/7
45. Rep lac e the ba ttery.