7/25/2019 M14355_R0 - King Cobra HS
1/78R0
M14355
King Cobra HS
Installation, Operation,
and Maintenance Manual
hook-strip option
P.O. Box 2327
2800 N. FrazierConroe, TX 77305-2327936-756-4800 phone
936-523-2788 fax
7/25/2019 M14355_R0 - King Cobra HS
2/78
7/25/2019 M14355_R0 - King Cobra HS
3/78
6Maintenance and Repair
7
5
Parts and Drawings
Troubleshooting
8Worldwide Locations
3
2
Installation
Product Information
General Information 1
4Operation
9Appendix
7/25/2019 M14355_R0 - King Cobra HS
4/78
Copyright 2003 Varco International, Inc.
Published in June 2003
Brandt is a registered trademark of Varco International, Inc.
King Cobra and BHX are trademarks of Varco International, Inc.
Isoflex is a registered trademark of Kluber Lubrication North America L.P.
WD-40 is a registered trademark of WD-40 Company.
Loctite is a registered trademark of Loctite Corporation U.S.A.
All other product, brand, or trade names used in this publication are the trademarks or registered
trademarks of their respective owners.
All rights reserved. This publication is the property of, and contains information proprietary to Varco
International, Inc. No part of this publication may be reproduced or copied in any form or by any
means, including electronic, mechanical, photocopying, recording or otherwise, without the prior
written permission of Varco International, Inc.
Information in this manual is subject to change without notice.
7/25/2019 M14355_R0 - King Cobra HS
5/78
7/25/2019 M14355_R0 - King Cobra HS
6/78
7/25/2019 M14355_R0 - King Cobra HS
7/78King Cobra HS 1-A
1
General InformationM14355 R0
Intended audience . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1
Conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1
Notes, cautions, and warnings . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1
Notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1
Cautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1
Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1
Illustrations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2
Safety requirements. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2
Personnel training . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2
Recommended tools . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2
General system safety practices. . . . . . . . . . . . . . . . . . . . . . . . . 1-3
Replacing components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3
Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3
Proper use of equipment. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3
7/25/2019 M14355_R0 - King Cobra HS
8/781-B Brandt
1
M14355 R0General Information
7/25/2019 M14355_R0 - King Cobra HS
9/78King Cobra HS 1-1
1
General InformationM14355 R0
Intended audience
This manual is intended for use by field engineering, installation, operation, and repairpersonnel. Every effort has been made to ensure the accuracy of the informationcontained herein. Brandt, a Varco company, will not be held liable for errors in this
material, or for consequences arising from misuse of this material.
Conventions
Notes, cautions, and warnings
Notes, cautions, and warnings appear throughout this manual to provide you with
additional information, and to advise you to take specific action to protect personnelfrom potential injury or lethal conditions. They may also inform you of actions
necessary to prevent equipment damage or conditions that may void your warranty.
Please pay close attention to these advisories.
Notes
Cautions
Warnings
The note symbol indicates that additional information is providedabout the current topic.
The caution symbol indicates potential risk of damage to equipmentor injury to personnel. Follow instructions explicitly and take extreme
care.
A caution symbol may also indicate a condition that voids your
equipment warranty.
The warning symbol indicates a definite risk of equipment
damage or danger to personnel. Failure to observe and followproper procedures is likely to result in serious or fatal injury to
personnel, significant property loss, or significant equipmentdamage.
7/25/2019 M14355_R0 - King Cobra HS
10/78
7/25/2019 M14355_R0 - King Cobra HS
11/78King Cobra HS 1-3
1
General InformationM14355 R0
General system safety practices
Local codes may apply. Please consult them prior to performing any operation.
The presence of a Brandt representative at the site does not relieve the owner/operator of responsibility to follow published installation, operation, and maintenance
instructions.
The equipment discussed in this manual may require or contain one or more utilities,such as electrical, hydraulic, pneumatic, or cooling water.
Isolate all energy sources before beginning work.
Avoid performing maintenance or repairs while the equipment is in operation.
Wear proper protective equipment during equipment installation, maintenance,or repair.
Replacing components
Verify that all components (such as cables, hoses, etc.) are tagged and labeled
during disassembly and reassembly of equipment.
Replace failed or damaged components with Brandt certified parts. Failure to doso could result in equipment damage or personal injury.
Maintenance
Equipment must be maintained on a regular and routine basis. See the servicemanual for maintenance recommendations.
Proper use of equipment
Brandt equipment is designed for specific functions and applications, and should beused only for its intended purpose.
Before installing or performing maintenance or repairs on equipment,read the following instructions to avoid endangering exposed persons
or damaging equipment.
Failure to conduct routine maintenance could result in equipmentdamage or injury to personnel.
7/25/2019 M14355_R0 - King Cobra HS
12/781-4 Brandt
1
M14355 R0General Information
7/25/2019 M14355_R0 - King Cobra HS
13/78King Cobra HS
A
2
Product InformationM14355 R0
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1
The role of a King Cobra HS separator. . . . . . . . . . . . . . . . . . . . 2-1
How the King Cobra HS works . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1
King Cobra HS basket and pivot system . . . . . . . . . . . . . . . . . . . . 2-1
Vibrator system. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-4
Unit description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-5
7/25/2019 M14355_R0 - King Cobra HS
14/78 B
Brandt
2
M14355 R0Product Information
7/25/2019 M14355_R0 - King Cobra HS
15/78King Cobra HS 2-1
2
Product InformationM14355 R0
Introduction
The role of a King Cobra HS separator
The Brandt King Cobra Hook Strip (HS) separator is a fine-screen linear motionshaker. The separator is almost always located at the flow line unless it is preceded
by a scalping or gumbo separator. The King Cobra HS removes a large percentageof drill cuttings before the mud is circulated through the surface mud system leading toimproved performance of downstream solid control equipment.
The King Cobra HS separator is designed to do two primary jobs: separate drilledsolids from the mud and transport the solids rapidly and efficiently off the screens.
How the King Cobra HS works
The three features key to the operation of the King Cobra HS are the basket and angleadjustment system, the vibrator system, and the screen tensioning system. Thesesystems work with the uniquely designed separator basket to give the highest fluid
throughput and driest solids in a compact and reliable separator.
King Cobra HS basket and pivot system
The basket's patented screen configuration is a major advance over previouslyavailable separators. During normal operation, with the basket in the neutral position,
the first screen will be evenly flooded with one (1) to two (2) inches of mud. The poolof mud creates an even hydrostatic head on the screen surface that increases the
amount of mud that can pass through the first three screens (See Figure 2-1).
7/25/2019 M14355_R0 - King Cobra HS
16/782-2 Brandt
2
M14355 R0Product Information
In traditional shakers, with all screens in the same plane, the operator must raise thebasket to create a liquid pool. The resulting pool is wedge shaped and can cause a
slow-moving solids bed to form (See Figure 2-2). The material in the slow-movingsolids bed is very slow to convey and is ground into fine solids, which negatively
affects the mud system. Screen life is also jeopardized due to slow-moving solids bedformation. Because the first screen of the King Cobra HS is flooded more evenly andshallowly, a slow-moving solids bed will not form, thus increasing screen life and
optimizing shaker performance.
Figure 2-2. Typical linear shaker angled uphill
showing a stationary solids bed
Liquid pool
Fine-mesh hook stripscreen
Primary screening surfaces
Screened fluid
Drying screen
Discharged solids
Figure 2-1. King Cobra HS under normal operating conditions
Liquid pool
Stationary solids bed
Discharged solids
7/25/2019 M14355_R0 - King Cobra HS
17/78King Cobra HS 2-3
2
Product InformationM14355 R0
The design of the King Cobra HS basket also includes a drying screen. During normaloperation, the liquid pool extends to the end of the third screen and the fourth screenis used to remove all excess liquid from the screened particles (dry the cuttings).
During flow surges or changes in flow conditions, liquid can run off of the end of thethird screen and onto the fourth screen. Fluid on the fourth screen flows to the rear of
the screen and builds up a second pool, preventing the loss of any whole mud off theend of the shaker. (See Figure 2-3)
The King Cobra HS has a manually operated basket angle adjustment system. Theangle adjustment system allows the basket to be tilted upward by as much as
three degrees and downward by as much as one degree. During unusually heavy flowconditions the basket can be pivoted uphill to increase the depth of the pool. This
deeper pool will allow the shaker to handle the unusual flow conditions without a lossof whole mud off the end of the shaker.
Sticky clays and gumbo often will not convey uphill and may not convey horizontally
with a linear motion shaker. When sticky clays or gumbo are encountered, the basketcan be tilted downward to make sure that the material conveys. The operator canadjust the basket angle while the unit is running by using the hand wheels located on
each side of the basket. An angle adjustment plate and safety pendant near the backof the basket show the basket angle and take the load off the jacking system during
normal operating conditions.
Liquid pool
Fine-mesh hook stripscreen
Primary screening surfaces
Screened fluid
Drying screen Discharged solids
Figure 2-3. King Cobra HS under upset operating conditions
7/25/2019 M14355_R0 - King Cobra HS
18/782-4 Brandt
2
M14355 R0Product Information
Vibrator system
The vibrator system includes the two canister type vibrator motors, a motor mountingmotion tube, and a plate. Each vibrator motor contains eccentric weights that generate
a circular shaking force when rotated. During operation the two motors rotate inopposite directions, creating a net linear shaking force on the basket. This linear
shaking force is directed through the center of mass of the basket, resulting in equallinear motion along the entire length of screening surface. The motion conveys the
solids along the screen, even uphill, and off the discharge end of the shaker. Thebasket motion has been carefully designed to give the unit optimum performance overa wide range of drilling conditions.
The angle of the basket's linear motion relative to a line perpendicular to the screen
surface is called the angle of attack (conveyance angle). The angle of the basketslinear motion relative to a line parallel to the screen surface is called the conductanceangle. The King Cobra HS uses a 40 conveyance angle and a 50 conductance
angle. See Figure 2-4 for a diagram of these angles.
Figure 2-4. Motion angle
50
9040
Conveyance angle
Conductance angle
Screen
Vibrator action line
7/25/2019 M14355_R0 - King Cobra HS
19/78King Cobra HS 2-5
2
Product InformationM14355 R0
Unit description
Physical
Unit Weight Length Width
Overall
Height
Weir
Height
King Cobra HS 4400 lb
(1996 kg)
119 3/8 in
(3032 mm)
66 1/8 in
(1679mm)
61 in
(1549mm)
34 in
(863mm)
Average operating noise level
dB Depth
75 3 m
80 1 m
Vibration level (no load)
State Motion
Factory setting 6.3 gs
In use, depending on setting of motor weights 3.5 - 7.0 gs
Electrical
Motors
Manufacturer Martin Engineering for Brandt
Type Three Phase Induction Motor
Frame 70 CDX18-8340-VM
Type TENV
UL RatingClass I, Groups C & D
Class II, Groups E, F, & G
Specifications
Hz HP
RPM
(synchronous) Volts Amps
50 2.50 1500 220/380 5.5/3.2
60 2.50 1800 230/460 7.0/3.5
60 2.50 1800 575 2.8
7/25/2019 M14355_R0 - King Cobra HS
20/782-6 Brandt
2
M14355 R0Product Information
7/25/2019 M14355_R0 - King Cobra HS
21/78King Cobra HS
3 A
3
InstallationM14355 R0
Inspection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1
Unit preparation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1
Electrical connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-2
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-4
Location and support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-4
Flow line connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-4
Screen installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-5
Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-7
During storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-7
Returning to service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-8
General recommendations and information . . . . . . . . . . . 3-9
7/25/2019 M14355_R0 - King Cobra HS
22/783 B
Brandt
3
M14355 R0Installation
7/25/2019 M14355_R0 - King Cobra HS
23/78King Cobra HS 3-1
3
InstallationM14355 R0
Inspection
Prior to setting up and operating a new King Cobra HS separator, inspect the goodsas received from the shipping company. A claim for damage or loss should bereported immediately to the carrier and to Brandt.
The tension bolt subassemblies (24) and screen crown rubbers (36) ship in a separate
box, and the tension rails (8) ship unattached. These items may be located in the backtank of the unit or under the skid. Check the bill of lading for any other separately
shipped items, including manuals and CDs.
Once it is confirmed the order has been received complete in undamaged condition,
installation of the King Cobra HS may begin.
Unit preparation
Read these instructions carefully and completely before you begin. Failure to do somay result in personal injury or damage to the unit.
1. Remove the four (4) shipping bolts and spacers (see Figure 3-1) and store in a
safe place for reuse.
Figure 3-1. King Cobra HS shipping bolt and spacer
2. Position sump discharge gate(s) on the sides of the shakers as needed for mudreturn to the sand trap or the degasser suction compartment or mud ditch.
3. Check all nuts, bolts, and fasteners on shaker.
4. Check to ensure the basket incline safety pins are properly inserted and that
they are in the same setting on both sides (see Basket angle on page 4-1).
5. Connect power (see Figure 3-2).
6. Install crown rubbers.
7. Install screens (see Figure 3-3).
The King Cobra HS can be lifted with a forklift or via the liftingeyes on each corner of the unit. When using the lifting eyes, use
shackles and a spreader bar to prevent damage to the unit.
shipping bolt and spacer
7/25/2019 M14355_R0 - King Cobra HS
24/783-2 Brandt
3
M14355 R0Installation
Electrical connections
Carefully proceed through this list to assure proper and safe operation of the unit(s).
As with any electrical equipment, all electrical work should be performed by a qualified
electrician. (see Figure 3-2)
1. Determine rig voltage supplied to unit. Be sure the motor operating voltage is amatch.
2. Lockout/tagout power from the power supply cable that will be connected to
unit.
3. Install power supply cable to motor starter. (see Figure 3-2 for starter wiringdiagram.) When connecting the power leads to the top of the contactor in thestarter enclosure, the three (3) incoming power leads are connected to the three
(3) left hand connections. Do not connect an incoming power lead to the farright hand connection.
4. Check for proper voltage (labeled on the starter enclosure) and make sure all
connections are tight. The motor junction boxes on the motors are pre-wired forthe correct voltage at the factory.
5. Remove the weight covers from one side of the vibrator motors.
6. Turn on power supply to unit.
7. Bump start the motors to check motor rotation. (To bump start the motors, push
the start button on the starter box, and then quickly push the stop button.)
8. Motors may rotate in either direction but ensure that the motors turn opposite toeach other or follow the arrows on the motors. If the motors turn in the same
direction, switch any two (2) wires on one (1) of the motors in the motor starterbox to reverse its direction.
9. Replace the motor weight covers. Bolt down the motor junction box covers andthe starter box cover.
10. Start the unit and check for proper vibration.
Follow all Lockout/Tagout procedures when making electricalconnections.
Wires in motor junction box must not be allowed to touch the inside ofthe junction box. Use the foam cushions supplied with the motor toprotect the wires.
Operation with both motors turning in the same direction will result in
very poor shaker performance.
7/25/2019 M14355_R0 - King Cobra HS
25/78King Cobra HS 3-3
3
InstallationM14355 R0
There should be no side-to-side motion of the basket. Check side-to-side motion byplacing a thumb and forefinger on either side of the upper basket rail. The motion of
the basket should cause the rail to slip between the thumb and fingers withouttouching the fingers.
Figure 3-2. King Cobra HS wiring diagram.
7/25/2019 M14355_R0 - King Cobra HS
26/783-4 Brandt
3
M14355 R0Installation
Installation
The following information provides the proper installation procedures for efficient andsafe operation. Please follow the recommendations closely. As always, adequateworking space, walkways, and handrails should be considered.
Location and support
The King Cobra HS is shipped assembled on a box type skid with an integral sump
and backtank. It is not necessary to weld the unit(s) to the support structure, as little orno vibration is transmitted through the coil spring suspension system. The supportstructure must be designed to support the shaker's dead weight of 4400 lb. (1996 kg),
plus a fluid load of 3000 lb. (1360 kg) for a total of 7400 lb. (3357 kg) per unit.
The operator needs access to both sides of the machine to change the screens. Allowat least 24 inches (0.6 meters) of free space around the machine. Catwalks or
walkarounds around the entire machine are very important, because they will increasethe chances of proper maintenance.
Some other guidelines for locating and installing the shaker include:
1. The unit(s) must be level in both directions to ensure even fluid distribution.
2. Do not weld or attach discharge troughs to the vibrating deck.
3. Do not install the solids slide above the bottom of the front shaker skid cutout.
Flow line connection
The flow line should connect near the bottom and center of the backtank. This will
minimize settling of solids. Over the top connection of the flow line to the backtank is
discouraged. If necessary, the pipe must be inserted at least two-thirds (2/3) to thebottom of the backtank to prevent solids buildup. Solids buildup in the backtank
results in an undesired reduction in the volume of the backtank and blockage of thedump valve. The drop or slope of the flow line should be a minimum of 1:12, or one
foot (or meter) of drop for each twelve feet (or meters) of the flow line.
The preferred hookup between multiple shakers is to use Y or T connectionsbetween the shakers. Use valves to regulate flow to each shaker. This way, one
shaker can still function while repairing or changing a screen on the other shaker. Forcontrolling flow, knife gate valves are preferred over butterfly valves.
Throughout this manual, the back of the King Cobra HS is the feedtank end, and the front is the end where the dried solids fall off. Left
and right are determined by looking at the machine from the front.
Surfaces of the equipment will be slippery. Use caution when workingon or around to avoid falling.
7/25/2019 M14355_R0 - King Cobra HS
27/78King Cobra HS 3-5
3
InstallationM14355 R0
Screen installation
Screen installation requires minimal time or effort. However, if you do not follow thesebasic steps, the result may be poor screen life and solids may pass into the active
system.
1. Check that all screen seals and crown rubbers are in place.
2. Check that tensioning hardware is properly assembled. See Figure 3-3for moreinformation.
3. Carefully lay in the new screen panel.
4. Install both draw bars (also called tension rails) and hand-tighten the tensioning
hardware. Check that the draw bar is fully seated in the screen hook.
5. Fully tighten the tensioning hardware.
To tighten the tensioning hardware:
a. Pull the screen hook strip up against the square bar welded to the right sideof the basket.
b. Center the screen on the support grid so that it covers both the leading and
trailing edge seals.
c. Tighten the right-side tensioning nut, compressing the spring until the coilsare about 1/32 apart (the thickness of a credit card).
d. Tighten the left-side tensioning nut, compressing the spring until the coilsare about 1/32 apart.
Tensioning nut
Spring alignment washer Spring
Tension bolt housing gasket
Tension bolt
Nylon spacer
Figure 3-3. Screen tensioning hardware
Do not bend the screen panel.
http://-/?-http://-/?-7/25/2019 M14355_R0 - King Cobra HS
28/783-6 Brandt
3
M14355 R0Installation
e. Check that the screen is tightening evenly as you apply tension. No wrinklesor ripples should be visible in the tensioned screen. Check that the screen
is drum-tight.
f. Check that the screen remains centered over the support grid and is sealedall the way around.
6. Check the screen tightness after 30 minutes of operation.
To check the screen tightness:
a. Check the spacing between the left-side coils. Tighten the tensioning nut as
needed.
b. Check the right-side draw bar. It should be pulled hard against the square
bar and the basket side. Tighten the draw bar as needed.
7/25/2019 M14355_R0 - King Cobra HS
29/78King Cobra HS 3-7
3
InstallationM14355 R0
Storage
Store the King Cobra HS in a cool, dry place with the ability to test the unit for three (3)hours once a month.
During storage
If the King Cobra HS is to be stored after receipt instead of being immediately installed
and operated the following steps should be taken to ensure that the unit does notdegrade during storage.
When stored in a cool, dry location with adequate power:
1. Keep shipping bolts on the shaker at all times while in storage, if movement ispossible. The only exception is when the shaker is tested once a month. After
the test or before shipment, replace the shipping bolts (Figure 3-1 on page 3-1).2. Test the operation of the shaker once a month. This requires connecting power
to the shaker, removing the shipping bolts, and running the shaker for three (3)hours.
3. Open the starter box cover and spray the components with a water displacing
solvent (for example, WD-40). Allow the solvent to dry, and then close thestarter cover tightly. Keep all other connections intact.
4. Replace the cable with a water-resistant material or short piece of cable if thepower source cable is removed from the starter box coupling. The starter box
must be sealed at all times.
When stored outside or with inadequate power:
1. Cover the shaker with a protective tarp if possible.
2. Keep shipping bolts on the shaker at all times while in storage.
3. Replace the cable with a water-resistant material or short piece of cable if the
power source cable is removed from the starter box coupling. The starter boxmust be sealed at all times.
4. Remove the starter box cover and spray the components with a water
displacing solvent (for example, WD-40) once a month. Allow solvent to drythen put the starter cover back on tightly. Keep all other connections intact.
7/25/2019 M14355_R0 - King Cobra HS
30/783-8 Brandt
3
M14355 R0Installation
Returning to service
Before returning the shaker to service after three (3) or more months of storage,
complete the following steps:
1. Remove motor covers and rotate shafts by hand.
2. Continue to rotate motor shaft while installing 5.7 grams (4 shots from a 400ggrease gun) of Kluber Isoflex Topas NB52 or NB152 grease into each bearing.
3. Remove shipping bolts and connect power to the machine.
4. Turn on power supply to unit.
5. Bump start the motors to check motor rotation. (To bump start the motors, push
the start button on the starter box, and then quickly push the stop button.)
6. Motors may rotate in either direction but ensure that the motors turn opposite toeach other or follow the arrows on the motors. If the motors turn in the same
direction, switch any two (2) wires on one (1) of the motors in the motor starter
box to reverse its direction.
7. Run shaker for three (3) hours and monitor motor bearing temperatures. Atstartup, the motors can run very hot, but after approximately three (3) hours,
should not operate at more than 70F above ambient temperature.
Operation with both motors turning in the same direction will result in
very poor shaker performance.
7/25/2019 M14355_R0 - King Cobra HS
31/78King Cobra HS 3-9
3
InstallationM14355 R0
General recommendations and
information Use the same mesh screen on all four panel sections. The cut point will
normally be determined by the coarsest mesh screen. If a coarser mesh screenis installed for any reason, it should be installed at the discharge end.
Use finer mesh screens, rather than coarse mesh screens, where gumbo orsticky clays are encountered. Finer mesh screens provide a much smootherand wetter surface than coarse mesh. Gumbo and clay tend to convey better on
smoother wetter surfaces and using finer screens often provides an immediatesolution to conveying problems.
Experiment with the basket angle to determine the best setting because
conveyance rates will vary with drilling rates and hole conditions.
Use the weir diverter plates in the backtank to balance the flow between two ormore shakers hooked to a common flow line. The weir diverter plates can alsobe used to change the flow of the liquid onto the screen surface. Adjust the weir
plates to get a less curved horseshoe to improve overall shaker performance.
If the solids being discarded are channeling to one side of the end screen as theshaker may be out of level. Correct this situation by shimming the corners of the
shaker skid until it is level. If the solids being discarded are channeling to bothsides of the end screen, or if the discarded solids are too wet, a 1/2 (13 mm)
wide bead of silicone applied to a clean dry screen will generally help.
Close the feed tank bypass valve during normal operation. After opening andclosing the valve, check to make sure that the valve is fully seated. Gravel or
hard cuttings may prevent the bypass valve from providing a positive seal.
Add replacement or makeup water while drilling, as required. Adding the waterto the feed tank generally reduces the mud viscosity and allows more efficientscreening.
Operate the King Cobra HS screens wet. Running with dry screens may result
in premature screen failure. Lower the deck angle or install finer mesh screensto extend the liquid pool. The end of the pool should be on the third screen.
Do not allow substantial amounts of mud to build up inside the vibrating deck.This may affect the units performance. A buildup of solids on or around themotors may cause overheating.
Check basket springs for bottoming-out. Worn or weak springs may allow thevibrating deck to fully collapse the springs under heavy mud loads. This will
cause unusual vibration patterns and damage to the unit. Replace springs inpairs, front or rear pair, or all four springs immediately. Slow bouncing or rockingmovements on the basket may indicate spring problems.
Inspect and replace worn or missing wear strips and crown rubbers. The wear
strips provide a positive seal around the screen panel. Worn or missing sealswill result in solids bypassing into the active system. Worn crown rubbers will
reduce screen panel support causing poor conveyance and throughout.
Wash down screens before shutting down the unit or before storing the screens.
Do not walk or lay tools on the screens.
7/25/2019 M14355_R0 - King Cobra HS
32/783-10 Brandt
3
M14355 R0Installation
7/25/2019 M14355_R0 - King Cobra HS
33/78King Cobra HS
4 A
4
OperationM14355 R0
Start up & operation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1
Basket angle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1
Screen blinding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-3
7/25/2019 M14355_R0 - King Cobra HS
34/784 B
Brandt
4
M14355 R0Operation
7/25/2019 M14355_R0 - King Cobra HS
35/78King Cobra HS 4-1
4
OperationM14355 R0
Start up & operation
The following sections provide instructions for normal operation. Before operating theunit(s) make sure that you performed all steps in Installation on page 3-3. The unit is
factory set to provide a G-force suitable for most drilling applications. Once the unithas been installed, the only changes or adjustments that should be made are screen
mesh and basket angle. Screen selection will depend upon your specified drillingparameters, such as circulating volume, mud viscosity, penetration rate, etc.
Basket angleThe pivoting system is used to change the angle of the screening surfaces relative to
the neutral position. The angle adjustment plates and the red safety pins are used tohold the shaker at the desired angle (see Figure 4-1).
.
Figure 4-1. Angle adjustment plates and angle-indicating safety pins
It is not necessary to shut down the shaker before changing the deck angle.
Screen selection is discussed in General recommendations andinformation on page 3-7.
Hand wheel
Adjustment
Safety pins
7/25/2019 M14355_R0 - King Cobra HS
36/784-2 Brandt
4
M14355 R0Operation
To change the basket angle:
1. Remove the red safety pins from the angle adjustment plates.
2. Use the hand wheels on both sides of the King Cobra HS to adjust the basketangle.
3. Adjust both sides to the same angle.
4. Replace the red safety pins when the desired screen angle has been reached.Make sure that the pins are in the same hole on both sides of the shaker.
5. Tighten both hand wheels.
For normal drilling conditions the unit should be operated with the basket tiltedbetween 2 degrees uphill and 2 degrees downhill so that the end of the liquid pool is
near the discharge end of the third screen. Additional uphill incline can be used tohandle an increase surge from bottoms up or an increased rate of penetration.Increasing the basket angle will move the end of the liquid pool towards the back of
the basket and allow the shaker to handle higher flow rates and/or produce driercuttings. The disadvantage of running the basket steeply uphill is the reduced
conveyance and a thicker solids bed. A thicker solids bed causes solids to be groundinto smaller pieces, wears out screens faster, and may increase the amount of fine
solids returned to the active mud system.
When gumbo or sticky clays are encountered it may be necessary to lower the basketangle to get the solids to convey properly. Although some baskets can be lowered to
as much as 5 degrees downhill, running the shaker at a lower angle than necessarywill require use of coarser screens to prevent excess drilling fluid loss.
Be sure to remove the pins from both sides.
Cuttings are generally dry enough for most applications when the endof the liquid pool is near the end of the third screen.
7/25/2019 M14355_R0 - King Cobra HS
37/78King Cobra HS 4-3
4
OperationM14355 R0
Screen blinding
If the screens openings plug (blind) with sand, there are several methods by which
the screen may be unplugged. If the screens are in the unit, rub the screens in a
circular motion with a cloth rag or cloth gloves. Or, with the screen removed, you maytry blowing out the solids with high-pressure air or water from the bottom.
Changing to a finer mesh screen may cause the near size sand that is blinding the
screens to be removed and discarded. Changing to a larger mesh screen may solvethe blinding problem, but will increase the amount of solids returned to the active
system.
Salt-water muds will sometimes cause calcium deposits to coat the wires in the
screen. As the layer of calcium increases in thickness around the wires, the openingsbecome plugged off. This usually results in flooding. Steam cleaning will usually
remove the calcium deposits.
Never use a wire or stiff fiber brush on the screens.
Often it is necessary to experiment with several mesh sizes tominimize blinding while drilling through unconsolidated sand
formations. As a general rule, try finer screens first.
7/25/2019 M14355_R0 - King Cobra HS
38/784-4 Brandt
4
M14355 R0Operation
7/25/2019 M14355_R0 - King Cobra HS
39/78
7/25/2019 M14355_R0 - King Cobra HS
40/785 B
Brandt
5
M14355 R0Troubleshooting
7/25/2019 M14355_R0 - King Cobra HS
41/78King Cobra HS 5-1
5
TroubleshootingM14355 R0
Troubleshooting
Motor
Symptom Probable cause Solution
Motors start but shaker
operation is very loud.
Shipping bolt(s) not
removed.
Remove shipping bolt(s).
Motor bearing failure. Loud
squalling noise is emitted.
Replace faulty motor.
Motors will not start (no
sound).
Power supply interrupted. Reconnect power.
Power cable failure. Repair or replace cable.
Overload relay tripped. Wait for automatic reset,then restart or open box
and reset manually.
Motor will not start, but
hums for a short period
until the overload trips.
Motor wired for incorrect
voltage.
Make sure motor is wired
for correct voltage.
Single phasing. Make sure all three phases
are at full voltage.
Motors run but trip off. Overload relay tripping
contactor.
Make sure both overload
relays are set to same
amperage as listed on
motor name plate.
Check for overload
condition.
Be sure both motors are
running and running in
opposite directions.
Only one motor running. Power cable failure. Repair or replace cable.
Motor failure. Replace faulty motor.
7/25/2019 M14355_R0 - King Cobra HS
42/785-2 Brandt
5
M14355 R0Troubleshooting
Screens
Symptom Probable cause Solution
Short screen life Improper handling - screens
damaged before operation
Handle screens with care-do not
step or lay tools on the screen
surfaceScreens overloaded - shakers
seeing very heavy sand or gumbo
Contact your local Brandt
representative - Brandt can build
custom screens to solve specific
problems
Screens loose Properly tighten screens
Deck cushions or edge seal worn,
dirty or not properly installed
Check deck cushions and edge
seals
Tension rail (draw bar) not seated
in the screen hook - screens
loosen during operation
Be sure tension rail seats all the
way to the bottom of the screen
hook and does not catch on the
hook reinforcement strip.
Tension rail bent or damaged Replace tension rail.
Dried or sticky solids stuck to
screens during operation
Wash off screens during operation
Install mister/sprayer (scalper
deck, only)
Defective screens Save defective screens for
warranty replacement
Solids do not
convey
Bad deck crown rubbers and edge
seals
Replace
Screens dry Add mister/sprayer
Wash off screens
Bad deck cushions Replace deck cushions
Screens loose Properly tighten screens
Screens too coarse Use finer screenSolids stuck to screens Wash off screens
Add mister
Screen up
7/25/2019 M14355_R0 - King Cobra HS
43/78King Cobra HS 6-A
6
Maintenance and RepairM14355 R0
Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-1
Lubrication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-1
Motor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-1
Basket angle and bypass adjustment wheels. . . . . . . . . . . . . . . . . 6-1
Ordering lubrication kits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-2
Maintenance Checks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-3
Repair . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-4
Replacing a motor. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-4
Replacing seal strips. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-5
Replacing screens . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-6
Repairing or patching screens . . . . . . . . . . . . . . . . . . . . . . . . . . 6-7
7/25/2019 M14355_R0 - King Cobra HS
44/786-B Brandt
6
M14355 R0Maintenance and Repair
7/25/2019 M14355_R0 - King Cobra HS
45/78King Cobra HS 6-1
6
Maintenance and RepairM14355 R0
Maintenance
The King Cobra HS separator requires very little maintenance. However, there areseveral maintenance checks that, if done on a regular basis, will provide extendedservice and performance.
Lubrication
Motor
Lubricate each bearing on the motors once every operating month (750 hours) per the
following instructions. Use only Kluber Isoflex Topas NB52 grease (P/N 46AS) foroperation in cold ambient temperatures of -20F to +50F. You may use either NB52
or NB152 for ambient temperatures of 50 to 100. For hot ambient temperatures
above 100 you must use Isoflex Topas NB152 grease (P/N 46AY).
1. Clean vibrator case around grease plug with a clean shop towel.
2. Remove grease plug from vibrator housing.
3. Install 1/8 NPT grease fitting (P/N 33B) into the vibrator housing. Always use a
new grease fitting. Even small amounts of another grease may cause anegative reaction with the Isoflex grease.
4. Install 5.7 grams of grease with a grease gun into each grease fitting. 5.7 grams
equals 4 shots from a 400g grease gun.
5. Replace the grease fitting with the grease plug.
6. Do not lubricate for another operating month. Too much grease will ruin themotor and void the warranty.
If motor has been running and not been lubricated for more than three (3) months, put
twenty (20) shots in each bearing and then four (4) additional shots each month perthe above instructions.
Basket angle and bypass adjustment wheels
Grease threads once per week with any lithium or lithium complex grease.
Using any grease other than Isoflex Topas will void the motor
warranty.
Do not mix Isoflex grease with any other grease.
Do not leave the grease fitting(s) in the vibrator housing.
7/25/2019 M14355_R0 - King Cobra HS
46/786-2 Brandt
6
M14355 R0Maintenance and Repair
Ordering lubrication kits
Follow the guidelines below to ensure that you order the proper lubrication kit.
Plastic laminated lubrication instructions are available free of chargefor attachment to each shaker. Request drawing PI7208.
For normal temperature conditions
Lubrication kit P/N 7221
Two (2) 1/8 NPT grease fittings P/N 33B.
One (1) 400 gram tube of Isoflex Topas grease P/N 46AS. (One tube
will lubricate 35 motors.)
One (1) set of lubrication instructions PI7208.
One (1) grease gun P/N 46AU (4 shots equals 5.7 grams / bearing)
For high ambient temperature conditions
Lubrication kit P/N 7221 H
Two (2) 1/8 NPT grease fittings P/N 33B.
One (1) 400 gram tube of Isoflex Topas grease P/N 46AY. (One tube
will lubricate 35 motors.)
One (1) set of lubrication instructions PI7208.
One (1) grease gun P/N 46AU (4 shots equals 5.7 grams / bearing)
7/25/2019 M14355_R0 - King Cobra HS
47/78King Cobra HS 6-3
6
Maintenance and RepairM14355 R0
Maintenance Checks
Component Tasks
Bypass valve Check after opening and closing for a positive
seal.Gravel or hard cuttings lodged in the valve seat
area may prevent a positive seal and mud
bypassing will occur.
Basket angle indicating safety
pins
Pins should be inserted in proper holes on each
side to provide a level deck. Tighten the
handwheels against the pins to prevent rattling.
Skid compartment Clean out any solids buildup that may cause the
vibrating deck to bottom out or interfere with
screening.
Screens Check for torn screens. Repair or replace if
necessary.
Screen cushions & seals Check crown rubbers and flat seals for damage or
wear. Replace as needed.
Nuts, bolts, fasteners Ensure all nuts, bolts, and lock washers are in
place and tight, particularly on the motors and the
motor mount beam clamps.
General operation Listen for any loud or unusual noise particularly
bearing squeal or any metal-to-metal contact. The
basket should run quietly.
7/25/2019 M14355_R0 - King Cobra HS
48/786-4 Brandt
6
M14355 R0Maintenance and Repair
Repair
Replacing a motor
If your bolt configuration does not match the design in Figure 6-1,see "Alternate boltconfigurations" on page 7/+18.
.
Figure 6-1. Standard bolt design
To replace a motor:
1. Turn off and Lockout/Tagout the power supply.
2. Disconnect electrical wiring from the motor to be replaced.
3. Use a sling or cable through the motor lifting eyes to support the weight of themotor before the mounting nuts or bolts are loosened.
4. Remove the six (6) motor mount bolts and heavy washers.
5. Remove the motor from the motor mount plate.
6. Clean threads with a bottoming tap and remove all rust from the mounting plate.
7. Note the location of the motor junction box cable through hole before picking upthe replacement motor. Mount the motor on the motor mount plate, bottommotor hole up; top motor hole down.
This section covers repairs that can be made in the field withoutspecial tools.
If your bolt configuration does not match the design in Figure 6-1,see "Alternate bolt configurations" on page 7/+18.
Part #
Hardened thick washer LC2A140
12-point 3/4 UNRC 2 1/2 bolt(torqued to 275 foot pounds)
22XU
LOCTITE Product 243(heavily coated)
18N
http://-/?-http://-/?-http://-/?-http://-/?-7/25/2019 M14355_R0 - King Cobra HS
49/78King Cobra HS 6-5
6
Maintenance and RepairM14355 R0
8. Use new bolts provided and existing thick washers to attach the new motor.Coat threads on new bolts with Loctite Product 243. Torque corners bolts first,
to 275 foot pounds.
9. Reconnect the electrical wiring to the motor.
10. Remove both weight covers from both motors. Check that all counterweightsare marked the same (Ex: 60Hz, 90 Hz)
11. Bump start the motors to check motor rotation. (To bump start the motors, push
the start button on the starter box, and then quickly push the stop button.)
12. Motors may rotate in either direction but ensure that the motors turn opposite toeach other or follow the arrows on the motors. If the motors turn in the same
direction, switch any two (2) wires on one (1) of the motors in the motor starterbox to reverse its direction.
13. Reinstall the motor weight covers.
14. Return the shaker to service.
15. After 30 minutes of operation, retorque the motor mounting bolts.
Replacing seal strips
To replace long wear strips:
1. Remove the old seal by cutting the christmas tree clips.
2. New seals should be formed prior to installation. When received from thefactory, they will be straight, but should be bent upward at each hole.
3. Install christmas tree clips in the new seal from the center outwards, alternatingfrom side to side. Do not hammer tight.
4. After all clips are started, hammer them tight.
To replace side wear strips:1. Remove the old fasteners with a screwdriver and back-up wrench and remove
the seal.
2. Clean all mating surfaces thoroughly.
3. Insert the new side wear strips with new fasteners.
4. Proper installation of the screens is now possible.
Never re-use old bolts.
Operation with both motors turning in the same direction will result in
very poor shaker performance.
7/25/2019 M14355_R0 - King Cobra HS
50/786-6 Brandt
6
M14355 R0Maintenance and Repair
To replace crown rubbers:
1. Remove the crown rubbers.
2. Clean the metal support thoroughly.
3. Replace with new crown rubbers.
Replacing screens
If you do not follow these basic steps, the result may be poor screen life and solidsmay pass into the active system.
1. If mud is circulating, open the backtank bypass valve or divert mud to other
shaker.
2. Wash down the screens while the shaker is running.
3. Shut down shaker.
4. Loosen the tensioning nut to release the draw bar on each side of the screen.
5. Remove the draw bars (also called tension rails). To do this, turn the tensionbolt 90 and pull it through the draw bar.
6. Remove the screen panel.
7. Replace worn or missing screen seals. Screen seals may be replaced asneeded but crown rubbers must be replaced in sets. Replacing individual crown
rubbers creates uneven support for the screen.
8. Replace all worn tensioning hardware. Look for bad threads, bent bolts,collapsed springs, and leaking seals. See Figure 6-2for more information.
Tensioning nut
Spring alignment washer
Spring
Tension bolt housing gasket
Tension bolt
Nylon spacerFigure 6-2. Screen tensioning hardware
http://-/?-http://-/?-7/25/2019 M14355_R0 - King Cobra HS
51/78King Cobra HS 6-7
6
Maintenance and RepairM14355 R0
9. Carefully lay in the new screen panel.
10. Install both draw bars (tension rails) and hand-tighten the tensioning hardware.Check that the draw bar is fully seated in the screen hook.
11. Fully tighten the tensioning hardware.
To tighten the tensioning hardware:
a. Pull the screen hook strip up against the square bar welded to the right sideof the basket.
b. Center the screen on the support grid so that it covers both the leading and
trailing edge seals.
c. Tighten the right-side tensioning nut, compressing the spring until the coils
are about 1/32 apart (the thickness of a credit card).d. Tighten the left-side tensioning nut, compressing the spring until the coils
are about 1/32 apart.
e. Check that the screen is tightening evenly as you apply tension. No wrinklesor ripples should be visible in the tensioned screen. Check that the screenis drum-tight.
f. Check that the screen remains centered over the support grid and is sealedall the way around.
12. Check the screen tightness after 30 minutes of operation.
To check the screen tightness:
a. Check the spacing between the left-side coils. Tighten the tensioning nut asneeded.
b. Check the right-side draw bar. It should be pulled hard against the squarebar and the basket side. Tighten the draw bar as needed.
Repairing or patching screens
You can extend the life of your shaker screens and save money by patching tornpanels.
To repair a screen using silicone, epoxy, or liquid steel:
1. Stop flow to shaker basket with torn screen using bypass valve or shut-off valve.
2. Wash screens.
3. Turn off shaker.
4. Dry off screen as much as possible. Backing cloth must not be torn.
Do not bend the screen panel.
7/25/2019 M14355_R0 - King Cobra HS
52/786-8 Brandt
6
M14355 R0Maintenance and Repair
5. Apply thick layer of repair material to torn panel and work into the backing cloth.
6. Allow to dry for at least thirty (30) minutes.
7. Start shaker.
8. Return flow to shaker.
Do not use silicone with diesel-based mud.
7/25/2019 M14355_R0 - King Cobra HS
53/78King Cobra HS
7 A
7
Parts and DrawingsM14355 R0
King Cobra HS spare parts . . . . . . . . . . . . . . . . . . . . . . . . . 7-1
King Cobra HS separator assembly A12500 . . . . . . . . . . . 7-2
A12500 parts list . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-3
King Cobra HS tension bolt sub-assembly SA14588 . . . 7-6
SA14588 parts list. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-7
King Cobra HS bypass valve sub-assembly SA9719 . . . . 7-8
SA9719 parts list. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-9
King Cobra HS jacking system SA9738 . . . . . . . . . . . . . 7-10
SA9738 parts list. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-11
King Cobra HS weir gate sub-assembly SA11556 . . . . . 7-12
SA11556 parts list. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-13
King Cobra HS 8 skid electrical systemleft hand C11225. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-14
C11225 parts list . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-15
King Cobra HS 8 skid electrical systemright hand C11224 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-16
C11224 parts list. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-17
Alternate bolt configurations . . . . . . . . . . . . . . . . . . . . . . 7-18
7/25/2019 M14355_R0 - King Cobra HS
54/787 B
Brandt
7
M14355 R0Parts and Drawings
7/25/2019 M14355_R0 - King Cobra HS
55/78King Cobra HS 7-1
7
Parts and DrawingsM14355 R0
King Cobra HS spare parts
1 year 2 year Description Part #
8 16 Spring spool LF3C10426
8 16 Long wear strip 12370-2
6 16 Side wear strip 12370-1
24 48 Crown rubber 12424
2 4 Lock pin assembly (safety pendant) LM3S00103
5 10 Cable clamp 01-1902
1 1 Shroud electrical 01-1903
1 1 Gland electrical BICC 01-1904
0 1 Overload relay option
Overload relay for 460V& 575V 24NV
Overload relay for 230V 24QR
0 1 Vibra motor option
60Hz 230/460V 01-2054-KC
60Hz 575V 01-2054-2KC
0 1 Jack screw subassembly 9738
0 1 Bypass valve subassembly 9719
7/25/2019 M14355_R0 - King Cobra HS
56/787-2 Brandt
7
M14355 R0Parts and Drawings
King Cobra HS separator assembly
A12500
7/25/2019 M14355_R0 - King Cobra HS
57/78King Cobra HS 7-3
7
Parts and DrawingsM14355 R0
A12500 parts list
Item # Part # Description Qty
1 11148 Skid & backtank weldment 1
2 11948 Basket weldment 1
3 11556 Weir gate subassembly 1
4 11225 Electrical system left hand 1
11224 Electrical system right hand 1
5 9738 Jack subassembly 2
6 11153 Pivot stand 2
7 9483-4 Pivot stand plate 4
8 22JN HHCS 3/8 16UNC x 3/4 8
9 9490-7 Starter plate 1
10 12358 Rockerarm weldment 2
11 12370-2 Long wear strip 8
12 12370-1 Side wear strip 8
13 12424 Crown rubber 24
14 LM3S00103 Safety pendant 2
15 22PY HHCS 3/8 16UNC x 1-1/2 8
16 36BL Washer flat 3/8 16
17 35CD Nut hex lock 3/8 8
18 LF3C10426 Spool spring 8
19 LF3B00936 Front spring 2
20 LM3B13614 Rear spring 2
21 22NC HHCS 3/4 10UNC x 3 2
22 22RO Screw 3/4-10UNC x 2-1/2 12
23 36AD Washer bevel 3/4 2
24 35AV Nut hex lock 3/4 2
25 11146-3 Discharge gate 1
26
27 63L Name plate 1
28 76CN Sticker 24 1
29 PI9878 Check-off list 1
30 63I Serial number plate 1
31 20AF Shipping bracket spacer 4
7/25/2019 M14355_R0 - King Cobra HS
58/787-4 Brandt
7
M14355 R0Parts and Drawings
32 22AU HHCS 1/2 13UNC x 6 4
33 36CG Washer flat 1/2 8
34 35CR Nut hex lock 1/2 13UNC 4
35 LC2A14014 Motor mounting washer 12
36 14588 Tension bolt subassembly 4
37 42CD Plug hex hd 3/4 NPT 2
38 07-332 Christmas tree clips 48
39 9719 Bypass valve subassembly 1
40 Motor option 1
99ACD 460V
99ACE 380V
99ACF 575V
41 36BK Washer flat 3/4 2
42 11546 Solids deflector plate sub assembly 1
43
44
45
46
47
48 22JU Screw 1/4-20 UNC x 1 24
49 35CA Nut hex lock 1/4-20 UNC 24
50 36AZ Washer flat 1/4 24
A12500 parts list (Continued)
Item # Part # Description Qty
7/25/2019 M14355_R0 - King Cobra HS
59/78King Cobra HS 7-5
7
Parts and DrawingsM14355 R0
7/25/2019 M14355_R0 - King Cobra HS
60/787-6 Brandt
7
M14355 R0Parts and Drawings
King Cobra HS tension bolt sub-assembly
SA14588
7/25/2019 M14355_R0 - King Cobra HS
61/78King Cobra HS 7-7
7
Parts and DrawingsM14355 R0
SA14588 parts list
Item# Part # Description Qty
1 35EB 3/4 10UNC x 2-1/4 brass coupling nut 1
2 12445 Spring alignment washer 1
3 30V Spring 1
4 12372 Tension bolt housing gasket 1
5 12416 Tension bolt 1
6 12446 Nylon spacer 1
7 12343 Tension rail (draw bar) 2
7/25/2019 M14355_R0 - King Cobra HS
62/787-8 Brandt
7
M14355 R0Parts and Drawings
King Cobra HS bypass valve sub-assembly
SA9719
7/25/2019 M14355_R0 - King Cobra HS
63/78King Cobra HS 7-9
7
Parts and DrawingsM14355 R0
SA9719 parts list
Item# Part # Description Qty
1 9728 Pilot plate weldment 1
2 9717 Bypass valve actuator weldment 1
3 22PF HHCS 3/8 16UNC x 3-1/2 1
4 36BL 3/8 flat washer 6
5 35CD 3/8 16UNC nylock hex lock nut 4
6 22PY HHCS 3/8 16UNC x 1-1/4 3
7 33B Grease fitting 1
7/25/2019 M14355_R0 - King Cobra HS
64/787-10 Brandt
7
M14355 R0Parts and Drawings
King Cobra HS jacking system
SA9738
7/25/2019 M14355_R0 - King Cobra HS
65/78King Cobra HS 7-11
7
Parts and DrawingsM14355 R0
SA9738 parts list
Item# Part # Description Qty
1 9856 Jack screw weldment 1
2 9702 Jack weldment 1
3 22NP HHCS 1/2 13UNC x 1-1/2 8
4 36CG Washer flat 1/2 16
5 9733-1 Item-1 2
6 35CR Nut hex 1/2 8
7 33B Grease fitting 1
7/25/2019 M14355_R0 - King Cobra HS
66/787-12 Brandt
7
M14355 R0Parts and Drawings
King Cobra HS weir gate sub-assembly
SA11556
7/25/2019 M14355_R0 - King Cobra HS
67/78King Cobra HS 7-13
7
Parts and DrawingsM14355 R0
SA11556 parts list
Item # Part # Description Qty
1 22RT Hair pin 2
2 36BK Washer flat 3/4 2
3 9490-8 Weir gate bar 1
4 10762 Weir plate 4
7/25/2019 M14355_R0 - King Cobra HS
68/787-14 Brandt
7
M14355 R0Parts and Drawings
King Cobra HS 8 skid electrical system
left hand C11225
7/25/2019 M14355_R0 - King Cobra HS
69/78King Cobra HS 7-15
7
Parts and DrawingsM14355 R0
C11225 parts list
Item # Part # Description Qty
1 10095 Starter option 1
01-2054 460V 60Hz motor
01-2054-1 380V 50Hz motor
01-2054-2 575V 60Hz motor
10440 380V 50Hz starter
10441 460V 60Hz starter
10442 575V 60Hz starter
2 76CU Decal Lockout/Tagout 1
3 220H HHCS 3/8 16UNC x 1 3/4 SST 4
4 36BL Washer flat 3/8 8
5 35CD Nut hex 3/8 16UNC SST 4
6 41F Cord grip 2
7 01-1904 Gland 3/4 NPT 4
8 01-1903 Shroud 4
9 01-1688 Cable 14 GA 4 conductor 2 @ 16
10 01-1902 Cable clamp 16
11 36AZ Washer flat 1/4 SST 10
12 03-2006 Nut hex 1/4 20UNC SST nylock 12
13 22TY HHCS 1/4 20UNC x 1 1/4 SST 3
14 22FV HHCS 1/4 20UNC x 3/4 2
15 01-2046 Terminal ring 14 GA to 1/4 12
16 60HX Wire ties 6
17 11222 Tool tray 1
7/25/2019 M14355_R0 - King Cobra HS
70/787-16 Brandt
7
M14355 R0Parts and Drawings
King Cobra HS 8 skid electrical system
right hand C11224
7/25/2019 M14355_R0 - King Cobra HS
71/78King Cobra HS 7-17
7
Parts and DrawingsM14355 R0
C11224 parts list
Item # Part # Description Qty
1 10095 Starter option 1
01-2054 460V 60Hz motor
01-2054-1 380V 50Hz motor
01-2054-2 575V 60Hz motor
10440 380V 50Hz starter
10441 460V 60Hz starter
10442 575V 60Hz starter
2 76CU Decal Lockout/Tagout 1
3 220H HHCS 3/8 16UNC x 1 3/4 SST 4
4 36BL Washer flat 3/8 8
5 35CD Nut hex 3/8 16UNC SST 4
6 41F Cord grip 2
7 01-1904 Gland 3/4 NPT 4
8 01-1903 Shroud 4
9 01-1688 Cable 14 GA 4 conductor 2 @ 16
10 01-1902 Cable clamp 16
11 36AZ Washer flat 1/4 SST 10
12 03-2006 Nut hex 1/4 20UNC SST nylock 12
13 22TY HHCS 1/4 20UNC x 1 1/4 SST 3
14 22FV HHCS 1/4 20UNC x 3/4 2
15 01-2046 Terminal ring 14 GA to 1/4 12
16 60HX Wire ties 6
17 11222 Tool tray 1
7/25/2019 M14355_R0 - King Cobra HS
72/787-18 Brandt
7
M14355 R0Parts and Drawings
Alternate bolt configurations
Figure 7-2. Bolt design 1
Figure 7-4. Bolt design 2
Part #
Hardened thick washer LC2A140 12-point 3/4 10UNC x 4 22XV
LOCTITE Product 243 (heavy coat) 18N
Washer 36AR
Heavy hex jam nut 35EA
Heavy hex nut(torqued to 380 foot pounds)
35DZ
Figure 7-1.
Part #
Hardened thick washer LC2A140
12-point 3/4 UNRC 2 1/2 bolt(torqued to 275 foot pounds)
22RU
LOCTITE Product 243 (heavy coat) 18N
Figure 7-3.
7/25/2019 M14355_R0 - King Cobra HS
73/78King Cobra HS 7-19
7
Parts and DrawingsM14355 R0
Figure 7-6. Bolt design 3
Figure 7-8. Bolt design 4
Part #
Hardened thick washer LC2A140 12-point 3/4 10UNC x 4 22XV
LOCTITE Product 243 (heavy coat) 18N
Heavy hex nylock nut 35DW
Washer 36AR
Figure 7-5.
.
Part #
Hardened thick washer LC2A140
12-point 3/4 UNRC 2 1/4 bolt(torqued to 275 foot pounds)
22RO
Washer 1.87 O.D. x.109 thick 36BK
LOCTITE Product 243 (heavy coat) 18N
Figure 7-7.
7/25/2019 M14355_R0 - King Cobra HS
74/787-20 Brandt
7
M14355 R0Parts and Drawings
7/25/2019 M14355_R0 - King Cobra HS
75/78King Cobra HS 7-A
8
Worldwide LocationsM14355 R0
International . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-1
United States . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-2
7/25/2019 M14355_R0 - King Cobra HS
76/787-B Brandt
8
M14355 R0Worldwide Locations
7/25/2019 M14355_R0 - King Cobra HS
77/78King Cobra HS 1-1
8
Worldwide LocationsM14355 R0
International
Argentina Bolivia
San Martin 345
4to Piso
Buenos Aires 1004
Argentina
KM 6.5 Carretera Antigua Acochabamba
(Al lado Casa Cotas)
Santa Cruz del la Sierra 3813
Bolivia
phone 54 114 394-3939
54 114 394-4599
54 114 394-6213
phone 591 33 553500
591 33 553501
591 33 554280
fax 54 114 394-4499 fax 591 33 553501
Brazil Canada
Padre Guilherme Lago Castro 559
Barrio Cancela Preta
Macae, Rio de Janeiro
Brazil
6616 - 45th Street
Leduc, Alberta T9E 7C9
Canada
phone 55 222 773-5437
55 222 773-3115
55 222 773-4197
55 222 773-3986
phone 780-986-6063
fax 55 222 763-9346
55 222 763-9343
fax 780-986-6362
Canada Equador
#1600 540-5thAvenue S.W.
Calgary, Alberta T2P 0M2
Canada
Luxemburgo 143 y Holanda
Edificio Luxemburgo Depto. 7A
Quito
Ecuador
phone 403-264-9646 phone 593 2-224-3212
593-2-224-3224
fax 403-263-8488 fax 593 2-224-3212
593 2-224-3224
593 2-246-5359
The Netherlands Norway
De Hulteweg 3b
7741 LE Coevorden
The Netherlands
Gamie Forusvn 25
Staveanger N-4033
Norway
phone 31 524-582718 phone 47 51-951460
fax 31 52-534814 fax 47 51-951470
Scotland United Arab Emirates
Badentoy Way
Badentoy Park
Portlethen, Aberdeen AB12 4YB
Scotland
P.O. Box 22148
Dubai, UAE
phone 44 1224-787700 phone 971 4-482468
fax 44 1224-784555 fax 971 4-482340
7/25/2019 M14355_R0 - King Cobra HS
78/78
M14355 R0Worldwide Locations
United States
California Colorado
7300 Downing Avenue
Bakersfield, CA 93308
410 17th Street, Suite 1170
Denver, CO 80202
phone 661-588-8503 phone 303-592-9250
fax 661-588-8506 fax 720-904-0693
Louisiana Louisiana
Advanced Wire Cloth
618 Hangar Drive
P.O. Box 9188 (70562)
New Iberia, LA 70560
1515 Poydras Street
Suite 1850
New Orleans, LA 70112
phone 337-365-7700 phone 504-636-3660
fax 337-365-0375 fax 504-636-3670
Lousiana North Dakota1327 Eraste Landry
P.O. Box 52252 (70505)
4965 2nd Street SW
P.O. Box 326 (58602)
Dickinson, ND 58601
phone 800-359-5935 phone 701-227-8608
fax 337-235-3739 fax 701-227-8612
Oklahoma Texas
3216 Aluma Valley Drive
P.O. Box 95169 (73143-5169)
Oklahoma City, OK 73121
426 Flato Road
Corpus Christi, TX 78405
phone 405-478-0047
800-725-4986
phone 361-289-7794
800-725-4974
fax 405-478-0177 fax 361-289-9058
Texas Texas
4506B Britmore
Houston, TX 77041
12950 West Little York
Houston, Texas 77041
phone 713-896-1172 phone 713-256-4100
fax 713-466-1496 fax 713-856-4133
Texas Wyoming