183
Sele
ctio
n G
uide
Prod
uct
Info
rmat
ion
Plas
tic B
earin
gM
ulti-
laye
r Bea
ring
Met
allic
Bea
ring
Air
Bear
ings
Tech
nica
l In
form
atio
nSl
ide
Shift
erCo
rpor
ate
Profi
le
140-183_複層系ベアリング.indd 183 19/11/13 18:25
Metallic Bearings
184
Oiles 500SP1 ……………………………………… P.185Oiles 500SP4 ……………………………………… P.209Oiles 500SPR ……………………………………… P.210Oiles 500SP5 ……………………………………… P.211Oiles 500HP ……………………………………… P.213Oiles 500AB ……………………………………… P.215Oiles 500B ………………………………………… P.217Oiles 500F ………………………………………… P.221Oiles 500 Spherical Bearings ………………… P.227Oiles 2000 ………………………………………… P.229Oiles Shoe Units ………………………………… P.245Oiles 2000S ……………………………………… P.247Oiles Cermet M …………………………………… P.249Oiles Cermet G …………………………………… P.255Oiles 300 …………………………………………… P.259Oiles 600 …………………………………………… P.269
184-271_金属系ヘ�アリンク�.indd 184 19/10/17 19:45
Oiles 500SP1 High-strength brass bearings with embedded solid lubricant
Feature●Serviceable without the need for lubrication.●Demonstrates high performance under high-load and low-speed operations.●Demonstrates superior wear resistance in applications where oil film is seldom
produced such as reciprocating motions, oscillation, frequent starts and stops, etc.●Superior chemical resistance and corrosion resistance.●Standard products are available in various sizes.
Ser vice range 500SP1 SL1 500SP1 SL4
Dry
-40~+80
49(150){500(1,530)}
0.25{15}
1.65{1,010}
Lubrication condition
Service temperature range ℃Allowable max. pressure P N/mm2{kgf/cm2}
Allowable max. velocity V m/s{m/min}
Allowable max. PV value N/mm2・m/s{kgf/cm2・m/min}
Dry
-40~+300
0.50{30}
1.65{1,010}
29(150){296(1,530)}
periodic lubrication
-40~+150
1.00{60}
3.25{1,990}
Relief angle
Rake angle
Nose radius (mm)
Speed (m/min)
Cut depth (mm)
Feed (mm/rev)
carbide tool(JIS)
5~10゜
2~5゜
0.40~0.80
100~200
0.05~0.30
0.08~0.30
Lathe turning
Cu
ttin
g t
ool
Con
dit
ion
I.D.
class 7 to 8
O.D.
class 6 to 7
Length
class 8 to 9
Machining accuracy (bushing)
Classes here are in JIS standard.This product demonstrates satisfactory performance at the slide surface roughness of Rz6.3 to 12.5μm.
Some products require application of solid lubricants on the sliding surface after processing.※Contact us for grinding and milling information.
※The values shown above are typical values, not the standard values.(Note)Compressive strength is 0.1%
The values in parentheses are static bearing pressures, which are the bearing pressures in applications with no motion or very small motion (≦0.0017m/s[0.1m/min]).
Density
Tensile strength
Tensile elongation at break
Compressive strength
Impact strength
Hardness
Modulus of longitudinal elasticity
Co-efficient of linear expansion
Thermal conductivity
JIS Z 2241
JIS Z 2241
JIS Z 2242
JIS Z 2243
7.8
755{77}
12
345{35}(Note)
19{1.9}
210
105,000{10,700}
2.12
87.8{0.21}
Mechanical proper tiesg/cm3
N/mm2{kgf/mm2}
%
N/mm2{kgf/mm2}
J/cm2{kgfm/cm2}
HBW
N/mm2{kgf/mm2}
×10-5 ℃-1
W/m℃{cal/sec℃cm}
Please indicate the type of motion (rotation, reciprocating, rotation & reciprocating) for custom-made products.Solid lubricant, SL401 and SL403 are not lead-free.
When you use standard 500SP1 seires in the temperature of 150℃ and over, contact us for more information.
Refer to page 36 for the suitable solid lubricant for made-to-order bearings.
185
Sele
ctio
n G
uide
Prod
uct
Info
rmat
ion
Plas
tic B
earin
gM
ulti-
laye
r Bea
ring
Met
allic
Bea
ring
Air
Bear
ings
Tech
nica
l In
form
atio
nSl
ide
Shift
erCo
rpor
ate
Profi
le
184-271_金属系ヘ�アリンク�.indd 185 19/10/17 19:45
Test data
0 10 20 30 40 50 60 70
Oscillation cycle〔×103cycles〕
0.3
0.25
0.2
0.15
0.1
0.05
0
Journal oscillation test 500SP1-SL4<Testing conditions>Bearing dimension : φ40×φ50×ℓ30Mating material : SUS304Pressure : 29.4N/mm2{300kgf/cm2}Velocity : 0.012m/s{0.75m/min}Oscillating cycle :12cpmOscillating angle : ±45°Test cycle : 70,000cycle(97.2h)Ambience : in the atmosphere, room temp.Lubrication : initial grease SL464g coating
W
Journal rotation test 500SP1-SL1<Testing conditions>Bearing dimension : φ40×φ50×R30Mating material : S45C high frequency quenchedPressure : 24.5N/mm2{250.0kgf/cm2}Velocity : 0.033m/s{2.0m/min}Test time : 100hrs.Ambience : in the atmosphere, room temp.Lubrication : dry
Journal oscillation test 500SP1-SL1<Testing conditions>Bearing dimension : φ40×φ50×R30Mating material : S45CPressure : 19.6N/mm2{200.0kgf/cm2}Velocity : 0.025m/s{1.5m/min}Oscillating cycle : 24cpmOscillating angle : ±45°Test time : 168hrs.Ambience : in the atmosphere, room temp.Lubrication : dry
0.5
0.4
0.3
0.2
0.1
0280 8456 140 168112
Coefficient of friction〔μ〕
Test time〔hrs.〕
Wear amount of bearing : 0.013mm
0.5
0.4
0.3
0.2
0.1
0100 20 30 40 908050 60 10070
Coefficient of friction〔μ〕
Test time〔hrs.〕
Wear amount of bearing : 0.020mm
W
W
W
Journal oscillation test 500SP1-SL4<Testing conditions>Bearing dimension : φ60×φ75×ℓ50Mating material : SUS403Pressure : 24.5N/mm2{250kgf/cm2}Velocity : 0.018m/s{1.13m/min}Oscillating cycle :12cpmOscillating angle : ±45°Test cycle : 70,000cycle(97.2h)Ambience : in the purified waterLubrication : initial grease SL464g coating
Wear amount of bearing : 0.005mm
0 10 20 30 40 50 60 70
Oscillation cycle〔×103cycles〕
0.3
0.25
0.2
0.15
0.1
0.05
0
Wear amount of bearing : 0.010mm
Coefficient of friction〔μ〕
Coefficient of friction〔μ〕
186
Selection Guide
ProductInform
ationPlastic Bearing
Multi-layer Bearing
Metallic Bearing
Air Bearings
Technical Inform
ationSlide Shifter
Corporate Profi le
184-271_金属系ヘ�アリンク�.indd 186 19/10/17 19:45
SPB Oiles 500SP1 SL1 Bushings (I.D. φ6~φ45)
I.D. O.D.
φd Tolerance φD Tolerance 108 2019161512
+0.010
+0.013
+0.013
+0.016
+0.016
+0.016
+0.016
+0.016
+0.016
+0.016
+0.020
+0.020
+0.020
+0.020
+0.020
+0.020
+0.020
+0.020
+0.020
+0.025
+0.025
+0.025
+0.025
+0.025
+0.025
+0.025
+0.025
+0.025
+0.025
+0.022
+0.028
+0.028
+0.034
+0.034
+0.034
+0.034
+0.034
+0.034
+0.034
+0.041
+0.041
+0.041
+0.041
+0.041
+0.041
+0.041
+0.041
+0.041
+0.050
+0.050
+0.050
+0.050
+0.050
+0.050
+0.050
+0.050
+0.050
+0.050
1012141819202122232426283032333538384040424445485055555660
+0.015
+0.018
+0.018
+0.018
+0.021
+0.021
+0.021
+0.021
+0.021
+0.021
+0.021
+0.021
+0.021
+0.025
+0.025
+0.025
+0.025
+0.025
+0.025
+0.025
+0.025
+0.025
+0.025
+0.025
+0.025
+0.030
+0.030
+0.030
+0.030
+0.006
+0.007
+0.007
+0.007
+0.008
+0.008
+0.008
+0.008
+0.008
+0.008
+0.008
+0.008
+0.008
+0.009
+0.009
+0.009
+0.009
+0.009
+0.009
+0.009
+0.009
+0.009
+0.009
+0.009
+0.009
+0.011
+0.011
+0.011
+0.011
061008081208101408121808
6 8 10 12 13 14 15 16 17 18 19 20 2022 25 2528 30 3031.532 35 3538 40 4045 4545
061010081210101410121810131910142010152110162210
182410
202810203010
061012081212101412121812131912142012152112162212
182412
202812203012223212253312253512
303812304012
081215101415121815131915142015152115162215172315182415192615202815203015223215253315253515
303815304015
405015405515
121816
152116162216
182416
202816203016
253316253516
121819
162219
202819
101420121820131920142020152120162220
182420192620202820203020223220253320253520283820303820304020
324220354420354520
405020
121825131925142025152125162225
182425
202825203025223225253325253525283825303825304025
354425354525
405025
25
※The I.D. tolerance after press fitting is for reference only.※I.D. φ50~φ200 are shown on pages 189 to 190.
Length L Tolerance-0.1-0.3
Motiondirection
Mating shaft Bushing
φdφD
Shaftd8: For general ( High-load)e7: For general (Low-load)f7: For high accuracy
L
1.6( )
Sh
aft
Specify Part No. by required I.D., O.D. and Length.
(e.g.) I.D. is 25mm, O.D. is 33mm, and length is 20mm.
SPB - 253320
6.3( )
chamfer
Housing
H7
All SPB bushings have engraved mark.
Part No.
The dimensional tolerances are the values measured at +25℃.
187
Sele
ctio
n G
uide
Prod
uct
Info
rmat
ion
Plas
tic B
earin
gM
ulti-
laye
r Bea
ring
Met
allic
Bea
ring
Air
Bear
ings
Tech
nica
l In
form
atio
nSl
ide
Shift
erCo
rpor
ate
Profi
le
184-271_金属系ヘ�アリンク�.indd 187 19/10/17 19:45
30 35 40 50 60 70 80 SPW
I.D.Washer
φd
06030803100312031303140315031603180318032005200525052505250530053005300535053505350535054007400740074507450745074507
152140162240
182440
202840203040
253340253540283840303840304040314040324240354440354540384840405040405540455540455640456040
202850203050
253350253550
303850304050
354450354550
405050405550455550455650456050
253360253560
303860304060
354460354560
405060405560455560455660456060
405070
456070
405080
456080
121830131930142030152130162230
182430
202830203030
253330253530283830303830304030314030324230354430354530
405030405530455530455630456030
152135162235
182435
202835203035
253335253535
303835304035
354435354535
405035405535455535455635456035
★
★
★★
★★
★★★
★★
★
+0.019
+0.025
+0.025
+0.031
+0.030
+0.030
+0.030
+0.030
+0.030
+0.030
+0.037
+0.037
+0.037
+0.037
+0.037
+0.037
+0.037
+0.037
+0.037
+0.046
+0.046
+0.046
+0.046
+0.046
+0.046
+0.045
+0.045
+0.045
+0.045
+0.007
+0.010
+0.010
+0.013
+0.012
+0.012
+0.012
+0.012
+0.012
+0.012
+0.016
+0.016
+0.016
+0.016
+0.016
+0.016
+0.016
+0.016
+0.016
+0.021
+0.021
+0.021
+0.021
+0.021
+0.021
+0.020
+0.020
+0.020
+0.020
Length L Tolerance-0.1-0.3
SPBSPW
Use this product together with the Oiles #500SP washer (SPW shown
on page 197) in a position where thrust loads are applied.
※Be sure to determine the position with a countersunk head screw and fix when the SPW with ★ shown in the table below is used, since the inner diameter is larger than the shaft diameter.
Set screw
Set screw
● Applicable to rotation, oscillation, and reciprocating motion.
● Do not use this under water.
● 31.5mm I.D bushing can be used as an intermediate trunnion
bushing for hydraulic cylinders.
15°
10°
R1~2
C0.3~0.5
L
0~4.5φdF7
φDm6
1~2.5
1.6
1.6
I.D. toleranceafter press
fitting (reference)
6 8 10 12 13 14 15 16 17 18 19 20 20 22 25 25 28 30 30 31.532 35 35 38 40 40 45 45 45
I t i s recommended to use a set screw to
prevent dislocation.
188
Selection Guide
ProductInform
ationPlastic Bearing
Multi-layer Bearing
Metallic Bearing
Air Bearings
Technical Inform
ationSlide Shifter
Corporate Profi le
184-271_金属系ヘ�アリンク�.indd 188 19/10/17 19:45
SPB Oiles 500SP1 SL1 Bushings (I.D. φ50~φ200)
I.D. O.D.
φd Tolerance φD Tolerance 20 6050403530+0.030
+0.030
+0.030
+0.030
+0.030
+0.030
+0.030
+0.030
+0.035
+0.035
+0.035
+0.035
+0.035
+0.035
+0.035
+0.035
+0.035
+0.040
+0.040
+0.040
+0.040
+0.040
+0.040
+0.040
+0.046
+0.046
+0.046
+0.046
+0.011
+0.011
+0.011
+0.011
+0.011
+0.011
+0.011
+0.011
+0.013
+0.013
+0.013
+0.013
+0.013
+0.013
+0.013
+0.013
+0.013
+0.015
+0.015
+0.015
+0.015
+0.015
+0.015
+0.015
+0.017
+0.017
+0.017
+0.017
70
+0.025
+0.025
+0.025
+0.030
+0.030
+0.030
+0.030
+0.030
+0.030
+0.030
+0.030
+0.030
+0.030
+0.030
+0.036
+0.036
+0.036
+0.036
+0.036
+0.043
+0.043
+0.043
+0.043
+0.043
+0.043
+0.043
+0.050
+0.050
+0.050
+0.050
+0.050
+0.060
+0.060
+0.060
+0.060
+0.060
+0.060
+0.060
+0.060
+0.060
+0.060
+0.060
+0.071
+0.071
+0.071
+0.071
+0.071
+0.083
+0.083
+0.083
+0.083
+0.083
+0.083
+0.083
+0.096
+0.096
60626570747575808590909596100100110120130140145150160170180190200210230
50505055606063657070757580808590100110120125130140150160170180190200
506040506240506540557040607440607540
658040708540
8096408010040
506050506250506550557050607450607550
658050708550709050759050
8096508010050
90110501001205011013050
506060506260506560557060607460607560637560658060708560709060759060759560809660
801006085100609011060
10012060
506070506270506570557070607470607570637570658070708570709070759070759570809670
8010070
100120701101307012014070
506020 506030506230506530557030607430607530
708530
506035506235
557035607435607535
708535
80
506080506280506580
607480607580637580658080708580709080759080759580809680
801008085100809011080
100120801101308012014080
13015080
1501708016018080
※Part No. with * are custom-made.※The I.D. tolerance after press fitting is for reference only.※I.D. φ6~φ45 are shown on pages 187 to 188.
Length L Tolerance-0.1-0.3
Part No.
Specify Part No. by required I.D., O.D. and Length.
(e.g.) I.D. is 80mm, O.D. is 96mm, and length is 70mm.
SPB - 809670
Motiondirection
Mating shaft Bushing
φdφD
Shaftd8: For general (High-load)e7: For general (Low-load)f7: For high accuracy
L
1.6( )
Sh
aft
6.3( )
chamfer
Housing
H7
All SPB bushings have engraved mark.
The dimensional tolerances are the values measured at +25℃.
189
Sele
ctio
n G
uide
Prod
uct
Info
rmat
ion
Plas
tic B
earin
gM
ulti-
laye
r Bea
ring
Met
allic
Bea
ring
Air
Bear
ings
Tech
nica
l In
form
atio
nSl
ide
Shift
erCo
rpor
ate
Profi
le
184-271_金属系ヘ�アリンク�.indd 189 19/10/17 19:45
90 100 120 130 140 150 200
I.D.Washer
φd
5008500850085508600860086508650870107010751075108010801090109010100101201012010-
-
-
-
-
-
-
-
-
★
★
★
901109010012090
12014090
5065100
6075100
7085100
759010075951008096100
80100100
90110100100120100110130100120140100125145100130150100140160100150170100160180100*170190100*180200100*190210100
809612080100120
90110120100120120110130120120140120125145120
130150130
80100140
100120140
120140140
140160140150170150160180150*170190150*180200150*190210150*200230150*200230200
SPW
Length L Tolerance-0.1-0.3
+0.045
+0.045
+0.045
+0.055
+0.055
+0.055
+0.055
+0.055
+0.054
+0.054
+0.054
+0.054
+0.054
+0.054
+0.065
+0.065
+0.065
+0.064
+0.064
+0.076
+0.076
+0.076
+0.076
+0.076
+0.076
+0.076
+0.088
+0.088
+0.020
+0.020
+0.020
+0.025
+0.025
+0.025
+0.025
+0.025
+0.024
+0.024
+0.024
+0.024
+0.024
+0.024
+0.030
+0.030
+0.030
+0.029
+0.029
+0.036
+0.036
+0.036
+0.036
+0.036
+0.036
+0.036
+0.042
+0.042
15°
10°
R1.5~4
C0.5~1.5
L
2.5~7.5φdF7
φDm6
2~5
1.6
1.6
50505055606063657070757580808590100110120125130140150160170180190200
I.D. tolerance
after press
fitting (reference)
●Applicable to rotation, oscillation, and reciprocating motion.
●Do not use this under water.
●63mm I.D bushing can be used as an intermediate trunnion
bushing for hydraulic cylinders.
SPBSPW
Use this product together with the Oiles #500SP washer (SPW shown
on page 197) in a position where thrust loads are applied.
Set screw
Set screw
It is recommended to use a set screw to prevent
dislocation.
※Be sure to determine the position with a countersunk head screw and fix when the SPW with
★ shown in the table below is used, since the inner diameter is larger than the shaft diameter.
190
Selection Guide
ProductInform
ationPlastic Bearing
Multi-layer Bearing
Metallic Bearing
Air Bearings
Technical Inform
ationSlide Shifter
Corporate Profi le
184-271_金属系ヘ�アリンク�.indd 190 19/10/17 19:45
SPBL Oiles 500SP1 SL4 Bushings
I.D. O.D.
φd Tolerance φD Tolerance
1215161820253035404045505055606570758090100110120130140150160170180190200
182122243035404550556060657075809095100110120130140150160170180190200210230
+0.032
+0.032
+0.032
+0.032
+0.040
+0.040
+0.040
+0.050
+0.050
+0.050
+0.050
+0.050
+0.050
+0.060
+0.060
+0.060
+0.060
+0.060
+0.060
+0.072
+0.072
+0.072
+0.072
+0.085
+0.085
+0.085
+0.085
+0.085
+0.085
+0.100
+0.100
+0.050
+0.050
+0.050
+0.050
+0.061
+0.061
+0.061
+0.075
+0.075
+0.075
+0.075
+0.075
+0.075
+0.090
+0.090
+0.090
+0.090
+0.090
+0.090
+0.107
+0.107
+0.107
+0.107
+0.125
+0.125
+0.125
+0.125
+0.125
+0.125
+0.146
+0.146
+0.034
+0.041
+0.041
+0.041
+0.041
+0.050
+0.050
+0.050
+0.050
+0.060
+0.060
+0.060
+0.060
+0.062
+0.062
+0.062
+0.073
+0.073
+0.073
+0.076
+0.076
+0.088
+0.088
+0.090
+0.090
+0.093
+0.093
+0.106
+0.106
+0.109
+0.113
+0.023
+0.028
+0.028
+0.028
+0.028
+0.034
+0.034
+0.034
+0.034
+0.041
+0.041
+0.041
+0.041
+0.043
+0.043
+0.043
+0.051
+0.051
+0.051
+0.054
+0.054
+0.063
+0.063
+0.065
+0.065
+0.068
+0.068
+0.077
+0.077
+0.080
+0.084
35302520 70605040
253525304025
121820152120162220182420203020253520304020354520
162230
203030253530304030354530405030
456030
354535
203040253540304040354540405040405540
506040506540557040
253550304050354550405050405550456050506050506550
607550
354560405060405560456060506060506560557060607560658060709060
80100609011060
10012060
506570557070607570658070709070759570
80
607580658080709080
80100809011080
10012080
12014080
※Part No. with * are made-to-order.※The I.D. tolerance after press fitting is for reference only.
L
1.6( )
Sh
aft
φdφD
Housing
H7
chamfer
6.3( )
Mating shaft Bushing
Shaftd8: For generalb9: For high-load and underwater use
Motiondirection
Length L Tolerance-0.1-0.3
Part No.
Specify Part No. by required I.D., O.D. and Length.
(e.g.) I.D. is 60mm, O.D. is 75mm, and length is 80mm.
SPBL - 607580
※Operating Temperature Range: -40~ +80˚C (-40~ +176˚F) Solid Lubricant : SL464 (refer to page 36)
The dimensional tolerances are the values measured at +25℃.
191
Sele
ctio
n G
uide
Prod
uct
Info
rmat
ion
Plas
tic B
earin
gM
ulti-
laye
r Bea
ring
Met
allic
Bea
ring
Air
Bear
ings
Tech
nica
l In
form
atio
nSl
ide
Shift
erCo
rpor
ate
Profi
le
184-271_金属系ヘ�アリンク�.indd 191 19/10/17 19:45
General・Underwater●Applicable to rotational, oscillating, and reciprocating motion.
●Be sure to apply grease supplied with the product to the inner sliding surface
before assembling the bearing. Run in the bearing.
●May be used over the maximum allowable speed or maximum allowable PV value
in short-time intermittent operations. Inquire us in such a case.
●Use a stainless steel or chrome-plated (30μm or more) mating shaft when using
the product in water, in a water-splashed place, etc.
●Use a mating shaft made of high-grade stainless steel with higher corrosion
resistance or plated with thicker chrome when using the product in severe
corrosive conditions. Supply grease for rust prevention.
●Provide the bushing with a set screw when using the product for high loads.
●Usable without the need for lubrication in the air and water. Use lithium grease
with extreme pressure additive if greasing is required.
100
I.D.
φd
70901007595100
8010010090110100
100120100110130100120140100130150100140160100150170100160180100*170190100*180200100*190210100
110
80100110
110130110
120
100120120
120140120
130
130150130
140
140160140
150
130150150
150170150160180150*170190150*180200150*190210150*200230150
90
*200230200
200
709090
80100909011090
1215161820253035404045505055606570758090100110120130140150160170180190200
L
C0.3~115°
2~5
10°φdE7
φDr6
R1.5~4
2.5~8.5
Length L Tolerance-0.1-0.3
+0.031
+0.026
+0.026
+0.026
+0.037
+0.032
+0.032
+0.046
+0.046
+0.040
+0.040
+0.040
+0.040
+0.053
+0.053
+0.053
+0.046
+0.046
+0.046
+0.060
+0.060
+0.052
+0.052
+0.068
+0.068
+0.065
+0.065
+0.065
+0.065
+0.078
+0.078
+0.013
+0.008
+0.008
+0.008
+0.016
+0.011
+0.011
+0.021
+0.021
+0.015
+0.015
+0.015
+0.015
+0.023
+0.023
+0.023
+0.016
+0.016
+0.016
+0.025
+0.025
+0.017
+0.017
+0.028
+0.028
+0.025
+0.025
+0.025
+0.025
+0.032
+0.032
1.6
I.D. tolerance
after press
fitting (reference)
192
Selection Guide
ProductInform
ationPlastic Bearing
Multi-layer Bearing
Metallic Bearing
Air Bearings
Technical Inform
ationSlide Shifter
Corporate Profi le
184-271_金属系ヘ�アリンク�.indd 192 19/10/17 19:45
SPF Oiles 500SP1 SL1 Flange Bushings
I.D. O.D. Flange
φd Tolerance φD Tolerance φF t Tolerance 1210 252320181715
6 8 10 12 13 14 15 16 18 20 25 30 31.535 40 45 50 55 60 63 65 70 75 80 90 100 120 130 140 150 160
1012141819202122243035404045505560657575808590100110120140150160170180
2223333335555555557.57.57.57.57.51010101010101010
162022252627282932404550506065707580908595105110120130150170180190200210
+0.019
+0.023
+0.023
+0.023
+0.028
+0.028
+0.028
+0.028
+0.028
+0.028
+0.034
+0.034
+0.034
+0.034
+0.034
+0.041
+0.041
+0.041
+0.043
+0.043
+0.043
+0.051
+0.051
+0.051
+0.054
+0.054
+0.063
+0.065
+0.065
+0.068
+0.068
+0.028
+0.034
+0.034
+0.034
+0.041
+0.041
+0.041
+0.041
+0.041
+0.041
+0.050
+0.050
+0.050
+0.050
+0.050
+0.060
+0.060
+0.060
+0.062
+0.062
+0.062
+0.073
+0.073
+0.073
+0.076
+0.076
+0.088
+0.090
+0.090
+0.093
+0.093
+0.020
+0.025
+0.025
+0.032
+0.032
+0.032
+0.032
+0.032
+0.032
+0.040
+0.040
+0.040
+0.050
+0.050
+0.050
+0.050
+0.050
+0.060
+0.060
+0.060
+0.060
+0.060
+0.060
+0.060
+0.072
+0.072
+0.072
+0.085
+0.085
+0.085
+0.085
+0.032
+0.040
+0.040
+0.050
+0.050
+0.050
+0.050
+0.050
+0.050
+0.061
+0.061
+0.061
+0.075
+0.075
+0.075
+0.075
+0.075
+0.090
+0.090
+0.090
+0.090
+0.090
+0.090
+0.090
+0.107
+0.107
+0.107
+0.125
+0.125
+0.125
+0.125
06100810101012101310
1510
06120812101212121312
15121612
0815101512151315141515151615181520152515
1017
1618
1020122013201420152016201820202025203020312035204020
1623
122513251425152516251825202525253025
35254025
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
Tolerance
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
※Part No. with * are made-to-order.※The I.D. tolerance after press fitting is for reference only.
L
Motiondirection
Mating shaft Flange bushing
φF
φdφD
Shaft
d8: For general (high-load)
e7: For general (low-load)
f7: For high accuracy
g6: For high accuracy (intermittent operation)
6.3( )
chamfer
Housing
H7
1.6( )
Sh
aft
t
Length L Tolerance-0.1-0.3
Part No.
Specify Part No. by required I.D. and Length.
(e.g.) I.D. is 50mm and length is 30mm.
SPF - 5030
The dimensional tolerances are the values measured at +25℃.
193
Sele
ctio
n G
uide
Prod
uct
Info
rmat
ion
Plas
tic B
earin
gM
ulti-
laye
r Bea
ring
Met
allic
Bea
ring
Air
Bear
ings
Tech
nica
l In
form
atio
nSl
ide
Shift
erCo
rpor
ate
Profi
le
184-271_金属系ヘ�アリンク�.indd 193 19/10/17 19:45
長さ L 公差 -0.1-0.3
30 35 40 50 60 67.5 80 100 120
I.D.
φd
1635183520352535303531353535403545355035
12301330
15301630183020302530303031303530403045305030
164018402040254030403140354040404540504055406040
25503050
3550405045505050
6050
7050
4560506055606060
6560
756080609060
63676080
7080
80809080
1008012080*13080*14080
80100
100100120100*130100*140100*150100*160100
*150120*160120
10°
15°
2.5~11
R1~4
1~4
φdE7
φDr6
φF
Lt
C0.3~0.5
+0.016
+0.021
+0.021
+0.031
+0.026
+0.026
+0.026
+0.026
+0.026
+0.037
+0.032
+0.032
+0.046
+0.046
+0.046
+0.040
+0.040
+0.055
+0.053
+0.053
+0.053
+0.046
+0.046
+0.046
+0.060
+0.060
+0.052
+0.068
+0.068
+0.065
+0.065
+0.004
+0.006
+0.006
+0.013
+0.008
+0.008
+0.008
+0.008
+0.008
+0.016
+0.011
+0.011
+0.021
+0.021
+0.021
+0.015
+0.015
+0.025
+0.023
+0.023
+0.023
+0.016
+0.016
+0.016
+0.025
+0.025
+0.017
+0.028
+0.028
+0.025
+0.025
Length L Tolerance-0.1-0.3
a
φd ~18R0.3
~160R1
~65R0.5
a: Chamfering for under flange
(mm)a
1.6
1.6
I.D. tolerance
after press
fitting (reference)
●Applicable to rotational, oscillating, and reciprocating motion.
●Flange surface is not subject to a thrust load as no lubricant is
embedded.
●Do not use this under water.
●31.5mm I.D. and 63mm I.D bushing can be used as an
intermediate trunnion bushing for hydraulic cylinders.
6 8 10 12 13 14 15 16 18 20 25 30 31.535 40 45 50 55 60 63 65 70 75 80 90 100 120 130 140 150 160
0~6
10°
R1~4
★ ★ ★★
★ 4 model number of SPF-6040/6050/6080/6367 is R1.
194
Selection Guide
ProductInform
ationPlastic Bearing
Multi-layer Bearing
Metallic Bearing
Air Bearings
Technical Inform
ationSlide Shifter
Corporate Profi le
184-271_金属系ヘ�アリンク�.indd 194 19/10/17 19:45
SPFG Oiles 500SP1 SL1 Thrust Bushings
2025
30
35
40455055657090110120140
6.3( )
chamfer
Housing
H7
Motiondirection
Mating shaft Flange bushing
φF
φdφD
Shaft
d8: For general (high-load)
e7: For general (low-load)
f7: For high accuracy
g6: For high accuracy (intermittent operation)
1.6( )
Sh
aft
Lt
Specify Part No. by required I.D. and Length.
(e.g.) I.D. is 35mm and length is 25mm.
Part No.SPFG - 3525
I.D. O.D. Flange
φd Tolerance φD Tolerance φF t ToleranceTolerance 25232018
68101213151618202530354050607080
1012141819212224283338445062748596
3333333355557881010
2025253030353540455055657090110120140
+0.019
+0.023
+0.023
+0.023
+0.028
+0.028
+0.028
+0.028
+0.028
+0.034
+0.034
+0.034
+0.034
+0.041
+0.043
+0.051
+0.051
+0.028
+0.034
+0.034
+0.034
+0.041
+0.041
+0.041
+0.041
+0.041
+0.050
+0.050
+0.050
+0.050
+0.060
+0.062
+0.073
+0.073
+0.020
+0.025
+0.025
+0.032
+0.032
+0.032
+0.032
+0.032
+0.040
+0.040
+0.040
+0.050
+0.050
+0.050
+0.060
+0.060
+0.060
+0.032
+0.040
+0.040
+0.050
+0.050
+0.050
+0.050
+0.050
+0.061
+0.061
+0.061
+0.075
+0.075
+0.075
+0.090
+0.090
+0.090
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
-0.03
-0.03
-0.03
-0.03
-0.03
-0.03
-0.03
-0.03
-0.03
-0.03
-0.03
-0.03
-0.03
-0.04
-0.04
-0.04
-0.04
11
0611
1211
13
08131013
131315131613
101812181318151816181818
2020252030203520
12231323152316231823
2025252530253525
※The I.D. tolerance after press fitting is for reference only.
Length L
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
The dimensional tolerances are the values measured at +25℃.
195
Sele
ctio
n G
uide
Prod
uct
Info
rmat
ion
Plas
tic B
earin
gM
ulti-
laye
r Bea
ring
Met
allic
Bea
ring
Air
Bear
ings
Tech
nica
l In
form
atio
nSl
ide
Shift
erCo
rpor
ate
Profi
le
184-271_金属系ヘ�アリンク�.indd 195 19/10/17 19:45
長さ L 公差 -0.1-0.3
27 35 37 38 47
I.D.
6048 6850 8058 90
4027
30353535
403750386038
4047
8060
50486048 6068
7050 7080
50586058
8090
+0.016
+0.021
+0.021
+0.031
+0.026
+0.026
+0.026
+0.026
+0.037
+0.032
+0.032
+0.046
+0.046
+0.040
+0.053
+0.046
+0.046
+0.004
+0.006
+0.006
+0.013
+0.008
+0.008
+0.008
+0.008
+0.016
+0.011
+0.011
+0.021
+0.021
+0.015
+0.023
+0.016
+0.016
Length L I.D. tolerance
after press
fitting (reference)
●Applicable to rotational, oscillating, and reciprocating motion.
●This bushing can be subject to both radial-journal and thrust load.
●Improve machining by more accurate flange thickness.
a: Chamfering for under flange
φd ~18R0.3
~50R0.5
~80R1
10°3.5~11
R1~215°
10° 1~4
φdE7
φDr6
φF
Lt
1.6
(mm)
a
a
1.6
1.6-0.1-0.3
φd
68101213151618202530354050607080
R
1.5~3.5 C0.3~0.5
10°
0~4
R1~2
196
Selection Guide
ProductInform
ationPlastic Bearing
Multi-layer Bearing
Metallic Bearing
Air Bearings
Technical Inform
ationSlide Shifter
Corporate Profi le
184-271_金属系ヘ�アリンク�.indd 196 19/10/17 19:45
SPW Oiles 500SP1 SL1 Thrust Washers
O.D. Thickness Mounting hole
φD T Tolerance
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
2528304040404050505050505555606070
33333333333555555
I.D.
φd Tolerance
6.28.210.212.212.213.214.215.216.216.218.220.225.225.230.230.235.2
+0.1
+0.1
+0.1
+0.1
+0.1
+0.1
+0.1
+0.1
+0.1
+0.1
+0.1
+0.1
+0.1
+0.1
+0.1
+0.1
+0.1
+0.2
+0.2
+0.2
+0.2
+0.2
+0.2
+0.2
+0.2
+0.2
+0.2
+0.2
+0.2
+0.2
+0.2
+0.2
+0.2
+0.2
No.of holes
Countersinkscrew sizeP.C.D
15182028
28283535
353540
45
50
M3M3M3M3
M3M3M3M3
M3M5M5
M5
M5
Part No.
SPW-0603SPW-0803SPW-1003SPW-1203SPW-1203NSPW-1303SPW-1403SPW-1503SPW-1603SPW-1603NSPW-1803SPW-2005SPW-2505SPW-2505NSPW-3005SPW-3005NSPW-3505
2222
2222
222
2
2
no hole
no hole
P.C.D
T
φdφD
●May be combined with the SPB.
●See the description of the SPB for combination.
(Pages 187 to 190)
●The products with the N marks at the end of
the part numbers have no mounting holes.
Part No.
Specify Part No. by required I.D. and thickness.
(e.g.) I.D. is 30.2mm and thickness is 5mm.
SPW - 3005
no hole
no hole
197
Sele
ctio
n G
uide
Prod
uct
Info
rmat
ion
Plas
tic B
earin
gM
ulti-
laye
r Bea
ring
Met
allic
Bea
ring
Air
Bear
ings
Tech
nica
l In
form
atio
nSl
ide
Shift
erCo
rpor
ate
Profi
le
184-271_金属系ヘ�アリンク�.indd 197 19/10/17 19:45
φd ~10.21.50.3
~18.22
0.4
~35.22.50.4
~45.23
0.5
~55.34
0.6
~100.55
0.8 (mm)
120.54
0.8
a b: Chamfering for I.D. and O.D.
a
b
a
b
O.D. Thickness Mounting hole
φD T Tolerance
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
0
0
0
0
0
0
0
0
0
0
0
0
8090100110120125130140150170190200
778888101010101010
I.D.
φd Tolerance
40.245.250.355.360.365.370.375.380.390.5100.5120.5
+0.1
+0.1
+0.1
+0.1
+0.1
+0.1
+0.1
+0.1
+0.1
+0.1
+0.1
+0.1
+0.2
+0.2
+0.3
+0.3
+0.3
+0.3
+0.3
+0.3
+0.3
+0.3
+0.3
+0.3
P.C.D
607075859095100110120140160175
M6M6M6M6M8M8M8M8M8M10M10M10
Part No.
SPW-4007SPW-4507SPW-5008SPW-5508SPW-6008SPW-6508SPW-7010SPW-7510SPW-8010SPW-9010SPW-10010SPW-12010
224444444444
Countersink type
φdφD
T
1.6 1.6
a
bNo hole type
No.of holes
Countersinkscrew size
b
C1
C1
φd
P.C.D
φD
T
1.6 6.3
198
Selection Guide
ProductInform
ationPlastic Bearing
Multi-layer Bearing
Metallic Bearing
Air Bearings
Technical Inform
ationSlide Shifter
Corporate Profi le
184-271_金属系ヘ�アリンク�.indd 198 19/10/17 19:45
SGF Oiles 500SP1 SL1 Flange Guide Bushings
●Applicable to rotation, oscillation, and
reciprocating motion.
●It is recommended to use a set screw to prevent
dislocation.
Part No.I.D. O.D. Flnage
φd Tolerance φD Tolerance φF tR
253040506065658080100100
35405565758080100100120120
710101010101010101010
45506575859090110110130130
Length
L
405070808080120100140100140
+0.021
+0.021
+0.025
+0.025
+0.030
+0.030
+0.030
+0.030
+0.030
+0.035
+0.035
0
0
0
0
0
0
0
0
0
0
0
+0.009
+0.009
+0.011
+0.011
+0.011
+0.011
+0.011
+0.013
+0.013
+0.013
+0.013
+0.025
+0.025
+0.030
+0.030
+0.030
+0.030
+0.030
+0.035
+0.035
+0.035
+0.035
1020202020202020202020
Tolerance
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
0
0
0
0
0
0
0
0
0
0
0
SGF-253540SGF-304050SGF-405570SGF-506580SGF-607580SGF-658080SGF-6580120SGF-80100100SGF-80100140SGF-100120100SGF-100120140
6.3( )
chamfer
Housing
H7
L
Flange bushing
t
Part No.
Specify Part No. by required I.D., O.D. and Length.
(e.g.) I.D. is 65mm, O.D. is 80mm, and length is 80mm.
SGF - 658080
C1 C1C1
R R2φdH7
φDm6
φF
Lt
1.6
1.6
φF
φdφD
Motion direction
1.6
3
The dimensional tolerances are the values measured at +25℃.
199
Sele
ctio
n G
uide
Prod
uct
Info
rmat
ion
Plas
tic B
earin
gM
ulti-
laye
r Bea
ring
Met
allic
Bea
ring
Air
Bear
ings
Tech
nica
l In
form
atio
nSl
ide
Shift
erCo
rpor
ate
Profi
le
184-271_金属系ヘ�アリンク�.indd 199 19/10/17 19:45
SGB Oiles 500SP1 SL1 Guide Bushings
Part No.I.D. O.D.
φd Tolerance φD Tolerance
25303540506080100120
405060607080100120140
±0.008
±0.008
±0.0095
±0.0095
±0.0095
±0.0095
±0.011
±0.011
±0.0125
Length
L Tolerance
405055607590120150180
+0.021
+0.021
+0.025
+0.025
+0.025
+0.030
+0.030
+0.035
+0.035
0
0
0
0
0
0
0
0
0
ℓ1 ℓ2
101015101520252525
55551010101010
SGB-254040SGB-305050SGB-356055SGB-406060SGB-507075SGB-608090SGB-80100120SGB-100120150SGB-120140180
-0.2
-0.2
-0.2
-0.2
-0.2
-0.2
-0.2
-0.2
-0.2
0
0
0
0
0
0
0
0
0
●Applicable to reciprocating motion.
●It is recommended to use a set screw to prevent
dislocation.
Motion direction Bushing
L
φdφD
Housing
H7
chamfer
6.3( )
Part No.
Specify Part No. by required I.D., O.D. and Length.
(e.g.) I.D. is 60mm, O.D. is 80mm, and length is 90mm.
SGB - 608090
C0.5C1
C2
C1R20
φdH7
φDjs6
Lℓ2 ℓ1
0.5
1.6
1.6
15°
The dimensional tolerances are the values measured at +25℃.
200
Selection Guide
ProductInform
ationPlastic Bearing
Multi-layer Bearing
Metallic Bearing
Air Bearings
Technical Inform
ationSlide Shifter
Corporate Profi le
184-271_金属系ヘ�アリンク�.indd 200 19/10/17 19:45
SWP Oiles 500SP1 SL1 Wear Plates
●Motion direction: width and length direction
4-C1ℓ1ℓ2 ℓ2
L
WW1
W2
W2
4-C1ℓ1ℓ2 ℓ2
L
W
Cross-section
Chamfering
Type A Type B
Motion direction Part No.
Specify Part No. by required width and length.
(e.g.) Width is 75mm and length is 200mm. SWP - 75200
L
T
W
φ17.5
T
G1.6
6.3 φ11 82
R10 allcircumferences
C3 allcircumferences
6
C3 allcircumferences
3.5
2
R5 allcircumferences
■Example of combination use with SLP.
SWP
SLP SWP
SLP
SWPSLP
201
Sele
ctio
n G
uide
Prod
uct
Info
rmat
ion
Plas
tic B
earin
gM
ulti-
laye
r Bea
ring
Met
allic
Bea
ring
Air
Bear
ings
Tech
nica
l In
form
atio
nSl
ide
Shift
erCo
rpor
ate
Profi
le
184-271_金属系ヘ�アリンク�.indd 201 19/10/17 19:45
ThicknessWidth
T ToleranceW
2020202020202020202020202020202020202020
W1 Type QtyW2 ℓ1 ℓ2
Length
L
7510012515075100125150200100125150200250150200250150200250
Tolerance Tolerance Tolerance Tolerance
484848487575757575100100100100100125125125150150150
Part No.
SWP-4875SWP-48100SWP-48125SWP-48150SWP-7575BSWP-75100BSWP-75125SWP-75150SWP-75200SWP-100100SWP-100125SWP-100150SWP-100200SWP-100250SWP-125150SWP-125200SWP-125250SWP-150150SWP-150200SWP-150250
Mounting hole intervals Attach bolts
Chamfering
4550751002550751001505075100150200100150200100150200
5050505050505050100100100
25 2525252537.537.537.5252525
1525252525252525252525252525252525252525
22222222244444444444
BBBBAAAAAAAAAAAAAAAA
±0.025
±0.025
±0.025
±0.025
±0.025
±0.025
±0.025
±0.025
±0.025
±0.025
±0.025
±0.025
±0.025
±0.025
±0.025
±0.025
±0.025
±0.025
±0.025
±0.025
±0.2
±0.2
±0.2
±0.2
±0.2
±0.2
±0.2
±0.2
±0.2
±0.2
±0.2
±0.2
±0.2
±0.2
±0.2
±0.2
±0.2
±0.2
±0.2
±0.2
±0.2
±0.2
±0.2
±0.2
±0.2
±0.2
±0.2
±0.2
±0.2
±0.2
±0.2
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
M10 Hexagonsocket head
M10 Hexagonsocket head
M10 Hexagonsocket head
M10 Hexagonsocket head
M10 Hexagonsocket head
M10 Hexagonsocket head
M10 Hexagonsocket head
M10 Hexagonsocket head
M10 Hexagonsocket head
M10 Hexagonsocket head
M10 Hexagonsocket head
M10 Hexagonsocket head
M10 Hexagonsocket head
M10 Hexagonsocket head
M10 Hexagonsocket head
M10 Hexagonsocket head
M10 Hexagonsocket head
M10 Hexagonsocket head
M10 Hexagonsocket head
M10 Hexagonsocket head
202
Selection Guide
ProductInform
ationPlastic Bearing
Multi-layer Bearing
Metallic Bearing
Air Bearings
Technical Inform
ationSlide Shifter
Corporate Profi le
184-271_金属系ヘ�アリンク�.indd 202 19/10/17 19:45
SFP Oiles 500SP1 SL1 Flat Plates
ThicknessWidth
T ToleramceW
10101010101010101010101010101010
Length
L a b Type Qty
75100125150751001251507510012515075100125150
+0.04
+0.04
+0.04
+0.04
+0.04
+0.04
+0.04
+0.04
+0.04
+0.04
+0.04
+0.04
+0.04
+0.04
+0.04
+0.04
+0.01
+0.01
+0.01
+0.01
+0.01
+0.01
+0.01
+0.01
+0.01
+0.01
+0.01
+0.01
+0.01
+0.01
+0.01
+0.01
18181818282828283838383848484848
Part No.
SFP-1875SFP-18100SFP-18125SFP-18150SFP-2875SFP-28100SFP-28125SFP-28150SFP-3875SFP-38100SFP-38125SFP-38150SFP-4875SFP-48100SFP-48125SFP-48150
Hole intervals Attach bolts
15252525152525251525252515252525
455075100455075100455075100455075100
M6 Hexagonsocket headM6 Hexagonsocket headM6 Hexagonsocket headM6 Hexagonsocket headM6 Hexagonsocket headM6 Hexagonsocket headM6 Hexagonsocket headM6 Hexagonsocket headM6 Hexagonsocket headM6 Hexagonsocket headM6 Hexagonsocket headM6 Hexagonsocket headM6 Hexagonsocket headM6 Hexagonsocket headM6 Hexagonsocket headM6 Hexagonsocket head
2222222222222222
C1 all circumferences
R2 all circumferencesφ11
φ6.7
7
T
4-C1a b a
L
W
W=18、28、38、48
Cross-section
G1.6
●Motion direction: length direction
Motion direction
Part No.
Specify Part No. by required width and length.
(e.g.) Width is 28mm and length is 150mm. SFP - 28150
LW
T
■Example of combination use with SLP.
SFP
SLP
SFPSLPSLP SFP
203
Sele
ctio
n G
uide
Prod
uct
Info
rmat
ion
Plas
tic B
earin
gM
ulti-
laye
r Bea
ring
Met
allic
Bea
ring
Air
Bear
ings
Tech
nica
l In
form
atio
nSl
ide
Shift
erCo
rpor
ate
Profi
le
184-271_金属系ヘ�アリンク�.indd 203 19/10/17 19:45
ThicknessWidth
T ToleramceW
101010101010101010101010
Length
L a b c d e Type Qty
100150200250300350100150200250300400
±0.025
±0.025
±0.025
±0.025
±0.025
±0.025
±0.025
±0.025
±0.025
±0.025
±0.025
±0.025
353535353535505050505050
Part No.
SFP-35100SFP-35150SFP-35200SFP-35250SFP-35300SFP-35350SFP-50100SFP-50150SFP-50200SFP-50250SFP-50300SFP-50400
Hole intervals Attach bolts
202020202020202020202020
605555706580605555706590
-5550706575-5550706590
--55706575--55706590
----6580----6590
M8Flat head
M8Flat head
M8Flat head
M8Flat head
M8Flat head
M8Flat head
M8Flat head
M8Flat head
M8Flat head
M8Flat head
M8Flat head
M8Flat head
234455234455
a b c d e a
L4-C1
W
C1 all circumferences
R2 all circumferencesφ16
φ9
6
T
W=35、50
W=75
ThicknessWidth
T ToleramceW
101010101010
Length
L a b c d e Type Qty
150200250300400500
±0.025
±0.025
±0.025
±0.025
±0.025
±0.025
757575757575
Part No.
SFP-75150SFP-75200SFP-75250SFP-75300SFP-75400SFP-75500
Hole intervals Attach bolts
202020202020
1108010585120115
- 8010590120115
- - - 85120115
-----115
M8Flat head
M8Flat head
M8Flat head
M8Flat head
M8Flat head
M8Flat head
4668810
C1 all circumferences
R5 all circumferencesφ16
φ9
6
T
3.5
a b c d e a
45
L 4-C1
W15
15
G1.6
G1.6 2
Cross-section
Cross-section
204
Selection Guide
ProductInform
ationPlastic Bearing
Multi-layer Bearing
Metallic Bearing
Air Bearings
Technical Inform
ationSlide Shifter
Corporate Profi le
184-271_金属系ヘ�アリンク�.indd 204 19/10/17 19:45
SLP Oiles 500SP1 SL1 L Type Plates
ThicknessWidth
TW
4545454545
Length
L Type Qty
200250300350500
Attach boltsHole intervals
44557
5050505050
a b c d
5570658080
5070657575
5570657575
fPart No.
SLP-50200ASLP-50250ASLP-50300ASLP-50350ASLP-50500A
e
----75
----80
●Motion direction: length direction
ThicknessWidth
TW
3030303030
Length
L Type Qty
100150200250400
Attach boltsHole intervals
M10M10M10M10M10
23446
3232323232
a
6055557075
Part No.
SLP-32100BSLP-32150BSLP-32200BSLP-32250BSLP-32400B
TW
(20)a20 b c d e
LC1
C1
C1
C1
C1
R2
φ11
32
1.66.3
15
C1R2
30+0.10
+0.05
11(10) 221.6
b
-55507070
c
--557070
d e
Cross-section
T
LC1C1
W
C1C1
a20 b c f (20)ed
R2
R2
4525+ 0.10
+ 0.05
28 0-0.05
φ11φ17.5
C1
20
50
14(22)
1.6
1.6
6.3
●Hexagonal socket head bolts are fitted.
LW
T
Motion direction
Part No.
Specify Part No. by required width and length.(e.g.) Width is 50mm and length is 300mm.
SLP - 50300A
C1
■Example of combination use with SWP or SFP.
SWP or SFPSLP
SWP or SFPSLP
0-0.05
6.3
6.3
--658075
----70
----75
Cross-section
C1 allcircumferences
C1 allcircumferences
M10 Hexagonsocket head
M10 Hexagonsocket head
M10 Hexagonsocket head
M10 Hexagonsocket head
M10 Hexagonsocket head
205
Sele
ctio
n G
uide
Prod
uct
Info
rmat
ion
Plas
tic B
earin
gM
ulti-
laye
r Bea
ring
Met
allic
Bea
ring
Air
Bear
ings
Tech
nica
l In
form
atio
nSl
ide
Shift
erCo
rpor
ate
Profi
le
184-271_金属系ヘ�アリンク�.indd 205 19/10/17 19:45
●Hexagonal socket head bolts are fitted.
TW
a20 b (20)c d e
C1C1
C1
C1
ThicknessWidth
TW
20202020
Length
L Type Qty
50100150200
Attach boltsHole intervals
2234
20202020
a b c d
10202020
30605555
--5550
---55
Part No.
SLP-2050SLP-20100SLP-20150SLP-20200
TW
ba d
LC0.5
ac
C0.5
C0.5 C0.5
C0.5 C0.5C0.5 C0.5
ThicknessWidth
TW15151515
Length
L Type Qty
50100150200
Attach boltsHole intervals
2234
15151515
a b c d10202020
30605555
--5550
---55
Part No.
SLP-1550SLP-15100SLP-15150SLP-15200
TW
ba d
L
ac
ThicknessWidth
TW
20202020
Length
L Type Qty
100150200400
Attach boltsHole intervals
26262626
a b c d
60555575
-555070
Part No.
SLP-26100CSLP-26150CSLP-26200CSLP-26400C
e
L 11.4
φ14φ9
6.3
2010
+0.10
+0.05
26(8) 189
C0.5R2R2
C0.5
1.6
1.6
R1 5.5
φ6.6
15(5) 10
R1
8.5
φ11
1.6
6.31.6
φ14φ9
2014(6)
8R1
R1
6.31.6
1.6 11.4
208+0.10
+0.05
157+0.10
+0.05
0-0.05
0-0.05
0-0.05
6.3
6.3
6.3
--5570
---75
---70
2346
Cross-section
Cross-section
Cross-section
C1 allcircumferences
M6 Hexagonsocket headM6 Hexagonsocket headM6 Hexagonsocket headM6 Hexagonsocket head
M8 Hexagonsocket headM8 Hexagonsocket headM8 Hexagonsocket headM8 Hexagonsocket head
M8 Hexagonsocket headM8 Hexagonsocket headM8 Hexagonsocket headM8 Hexagonsocket head
206
Selection Guide
ProductInform
ationPlastic Bearing
Multi-layer Bearing
Metallic Bearing
Air Bearings
Technical Inform
ationSlide Shifter
Corporate Profi le
184-271_金属系ヘ�アリンク�.indd 206 19/10/17 19:45
SLC Oiles 500SP1 SL1 Slide Guide Rails
Part No.SLC - 41100
Thickness Width Attach bolts
T W
3030303041414141565656
W1 Type QtyW2ℓLength
L
100130160220100130160220100160220
Tolerance Tolerance
2323232323232323282828
Part No.
SLC-30100SLC-30130SLC-30160SLC-30220SLC-41100SLC-41130SLC-41160SLC-41220SLC-56100SLC-56160SLC-56220
6090606060906060606060
1515151515151515202020
7.57.57.57.57.57.57.57.5101010
22342234234
-0.01
-0.01
-0.01
-0.01
-0.01
-0.01
-0.01
-0.01
-0.01
-0.01
-0.01
-0.05
-0.05
-0.05
-0.05
-0.05
-0.05
-0.05
-0.05
-0.05
-0.05
-0.05
+0.05
+0.05
+0.05
+0.05
+0.05
+0.05
+0.05
+0.05
+0.05
+0.05
+0.05
+0.02
+0.02
+0.02
+0.02
+0.02
+0.02
+0.02
+0.02
+0.02
+0.02
+0.02
0
0
0
0
0
0
0
0
0
0
0
-0.05
-0.05
-0.05
-0.05
-0.05
-0.05
-0.05
-0.05
-0.05
-0.05
-0.05
t1 Tolerance
1515151526262626262626
t2
2323232334343434474747
φd1
77777777999
φd2
1111111111111111141414
20 ℓ 20 C1C1
C1
L
C1
C1
C1
C1
W φd2
t 2
W2
T
C1
φd1
W1
t 1
6.3
1.6
1.6
6.3
●Motion direction: length direction
Clearance needed
SLC
6.3
T
WL
Motion direction
■Example of attachment.
Specify Part No. by required thickness and length.
(e.g.) Thickness is 20mm and length is 100mm.
M6 Hexagonsocket headM6 Hexagonsocket headM6 Hexagonsocket headM6 Hexagonsocket headM6 Hexagonsocket headM6 Hexagonsocket headM6 Hexagonsocket headM6 Hexagonsocket headM8 Hexagonsocket headM8 Hexagonsocket headM8 Hexagonsocket head
207
Sele
ctio
n G
uide
Prod
uct
Info
rmat
ion
Plas
tic B
earin
gM
ulti-
laye
r Bea
ring
Met
allic
Bea
ring
Air
Bear
ings
Tech
nica
l In
form
atio
nSl
ide
Shift
erCo
rpor
ate
Profi
le
184-271_金属系ヘ�アリンク�.indd 207 19/10/17 19:45
SLI Oiles 500SP1 SL1 Slide Guide Rails for Additional Machining
T
WL
Part No.SLI - 20300
Thickness Width
T W
2025
W1 W2
Length
L
300300
Tolerance Tolerance
1523
Part No.
SLI-20300SLI-25300
Attachmenttype
1015
58
-0.01
-0.01-0.05
-0.05
+0.05
+0.05+0.02
+0.02
0
0 -0.05
-0.05
t Tolerance
1110
AB
C1C1
C1
L
T
C0.5
C1
C1
C1
W
C1
W1
W2
t
6.3
1.6
1.6
6.3
6.3
Clearance needed
SLI
Clearance needed
3
SLI
●This slide guide rail may be cut to the necessary dimension or bored for bolts.
●The movement direction is lengthwise.
■Attachment type A ■Attachment type B
Specify Part No. by required thickness and length.
(e.g.) Thickness is 20mm.
Motion direction
208
Selection Guide
ProductInform
ationPlastic Bearing
Multi-layer Bearing
Metallic Bearing
Air Bearings
Technical Inform
ationSlide Shifter
Corporate Profi le
184-271_金属系ヘ�アリンク�.indd 208 19/10/17 19:45
Oiles 500SP4 High-strength brass bearings with embedded solid lubricant
Feature●500SP4 is a self-lubricating bearing with embedded solid lubricant and metal
base that conforms to the universally-acknowledged ASTM Standards (C86300).●Serviceable without the need for lubrication.●Demonstrates high performance under high-load and low-speed operations.●Demonstrates superior wear resistance in applications where oil film is seldom
produced such as reciprocating motions, oscillation, frequent starts and stops, etc.●Superior chemical resistance and corrosion resistance.
Relief angle
Rake angle
Nose radius (mm)
Speed (m/min)
Cut depth (mm)
Feed (mm/rev)
carbide tool(JIS)
5~10゜
2~5゜
0.40~0.80
100~200
0.05~0.30
0.08~0.30
Lathe turning
Cu
ttin
g t
ool
Con
dit
ion
I.D.
class 7 to 8
O.D.
class 6 to 7
Length
class 8 to 9
Machining accuracy (bushing)
Classes here are in JIS standard.
This product demonstrates satisfactory performance at the slide surface roughness of Rz6.3 to 12.5μm.
Some products require application of solid lubricants on the sl iding surface after processing.
※Contact us for grinding and milling information.
※The values shown above are typical values, not the standard values.(Note)Compressive strength is 0.1%
Density
Tensile strength
Tensile elongation at break
Compressive strength
Impact strength
Hardness
Modulus of longitudinal elasticity
Co-efficient of linear expansion
Thermal conductivity
JIS Z 2241
JIS Z 2241
JIS Z 2242
JIS Z 2243
7.8
755{77}
12
345{35}(Note)
19{1.9}
223
105,000{10,700}
2.2
87.8{0.21}
Mechanical proper tiesg/cm3
N/mm2{kgf/mm2}
%
N/mm2{kgf/mm2}
J/cm2{kgfm/cm2}
HBW
N/mm2{kgf/mm2}
×10-5 ℃-1
W/m℃{cal/sec℃cm}
Please indicate the type of motion (rotation, reciprocating, rotation & reciprocating) for custom-made products.Solid lubricant, SL401 and SL403 are not lead-free.
Ser vice range 500SP 4 SL1Lubrication condition
Service temperature range ℃Allowable max. pressure P N/mm2{kgf/cm2}
Allowable max. velocity V m/s{m/min}
Allowable max. PV value N/mm2・m/s{kgf/cm2・m/min}
Dry
-40~+300
0.50{30}
1.65{1,010}
29(150){296(1,530)}
periodic lubrication
-40~+150
1.00{60}
3.25{1,990}
The values in parentheses are static bearing pressures, which are the bearing pressures in applications with no motion or very small motion (≦0.0017m/s[0.1m/min]).
※Above values are applicable when solid lubricants SL1 are used.
※Use the solid lubricant SL464 (lead-free) in water or in environments where the bearings are always exposed to water splashes. The operating temperature range is from -40˚C to +80˚C (-40°F to 176°F).
209
Sele
ctio
n G
uide
Prod
uct
Info
rmat
ion
Plas
tic B
earin
gM
ulti-
laye
r Bea
ring
Met
allic
Bea
ring
Air
Bear
ings
Tech
nica
l In
form
atio
nSl
ide
Shift
erCo
rpor
ate
Profi
le
184-271_金属系ヘ�アリンク�.indd 209 19/10/17 19:45
Oiles 500SPR Hard special copper alloy bearings with embedded solid lubricant
Test data
Features●Applicable to higher pressure than
500HP.●Help realize a long-life operation or
a compact design.
The values in parentheses are static bearing pressures, which are the bearing pressures in applications with no motion or very small motion (≦0.0017m/s[0.1m/min]).
※Above values are applicable when solid lubricants SL1 are used.
Ser vice range 500SPR SL1Lubrication condition
Service temperature range ℃Allowable max. pressure P N/mm2{kgf/cm2}
Allowable max. velocity V m/s{m/min}
Allowable max. PV value N/mm2・m/s{kgf/cm2・m/min}
Dry
0.25{15}
1.65{1,010}
-40~+150
90(200){918(2,041)}
periodic lubrication
0.50{30}
3.25{1,990}
JIS Z 2241
JIS Z 2241
7.49
780{79}
1.0
460{47}(Note)
Mechanical proper tiesg/cm3
N/mm2{kgf/mm2}
%
N/mm2{kgf/mm2}
Journal oscillation test 500SPR-SL1<Testing conditions>Bearing dimension : φ60×φ75×ℓ42Mating material : SCM440 quenched by high frequency
induction hardeningPressure : 90N/mm2{918kgf/cm2}Volocity : 0.008m/s{0.47m/min}Oscillation cycle : 5cpmOscillation angle : ±45°Test time : 100hrs.Ambience : in the atmosphere, room temp.Lubricataion : initially-greased only
※The values shown above are typical values, not the standard values.(Note)Compressive strength is 0.1%
Density
Tensile strength
Tensile elongation at break
Compressive strength
JIS Z 2243
280
105,000{10,720}
1.97
HBW
N/mm2{kgf/mm2}
×10-5 ℃-1
Hardness
Modulus of longitudinal elasticity.
Co-efficient of linear expansion
Please indicate the type of motion (rotation, reciprocating, rotation & reciprocating) for custom-made products.
Solid lubricant, SL401 and SL403 are not lead-free.
100
80
60
40
20
00 4020 80 10060
Beari
ng
tem
pera
ture〔℃〕
Test time〔hrs.〕
Bearing wear amount:0.021mm
Bearing temperature
0.30
0.25
0.20
0.15
0.10
0.05
0.000 20 40 8060 100
Coeff
icie
nt
of
fric
tion〔μ〕
Test time〔hrs.〕
Bearing wear amount:0.021mm
Co-efficient of friction
210
Selection Guide
ProductInform
ationPlastic Bearing
Multi-layer Bearing
Metallic Bearing
Air Bearings
Technical Inform
ationSlide Shifter
Corporate Profi le
184-271_金属系ヘ�アリンク�.indd 210 19/10/17 19:45
Oiles 500SP5 Special high-strength brass bearings with embedded solid lubricant
Feature●Bears higher loads than the 500SP1.●Demonstrates superior wear resistance under high-load and low-speed
applications.
※The values shown above are typical values, not the standard values.(Note)Compressive strength is 0.1%
Ser vice range 500SP 5 SL1Lubrication condition
Service temperature range ℃Allowable max. pressure P N/mm2{kgf/cm2}
Allowable max. velocity V m/s{m/min}
Allowable max. PV value N/mm2・m/s{kgf/cm2・m/min}
-40~+150
49(170){500(1,735)}
Dry
0.25{15}
1.65{1,010}
periodic lubrication
0.50{30}
3.25{1,990}
The values in parentheses are stat ic bearing pressures, which are the bearing pressures in appl ica t ions wi th no mot ion or very smal l mot ion (≦0.0017m/s[0.1m/min]).
※Above values are applicable when solid lubricants SL1 are used.
Density
Tensile strength
Tensile elongation at break
Compressive strength
Hardness
Modulus of longitudinal elasticity.
Co-efficient of linear expansion
JIS Z 2241
JIS Z 2241
JIS Z 2243
7.8
785{80}
10
392{40}(Note)
235
98,000{10,000}
2.13
Mechanical proper tiesg/cm3
N/mm2{kgf/mm2}
%
N/mm2{kgf/mm2}
HBW
N/mm2{kgf/mm2}
×10-5 ℃-1
Please indicate the type of motion (rotation, reciprocating, rotation & reciprocating) for custom-made products.
Solid lubricant, SL401 and SL403 are not lead-free.
211
Sele
ctio
n G
uide
Prod
uct
Info
rmat
ion
Plas
tic B
earin
gM
ulti-
laye
r Bea
ring
Met
allic
Bea
ring
Air
Bear
ings
Tech
nica
l In
form
atio
nSl
ide
Shift
erCo
rpor
ate
Profi
le
184-271_金属系ヘ�アリンク�.indd 211 19/10/17 19:45
SP5B Oiles 500SP5 SL1 Ultrathin Bushings
A long-life bearing with compact design and high durability.Its wall thickness is 33-50% thinner comparing to #500SP1-SL1 "SPB series (P187)".As it is made of OILES original metal material that has high strength and wear resistance, it has a long operating life inspite of possessing a thin wall.
Specify Part No. by required I.D., O.D. and Length.
(e.g.) I.D. is 10mm, O.D. is 12mm, and length is 15mm.
Part No.SP5B - 101215
Motion direction Mating shaft Bushing
φd
φD
Shaftd8: For general (High-load)e7: For general (Low-load)f7: For high accuracy
L
1.6( )
Sh
aft
Housing
H7
Chamfer
6.3( )
15°
Tapered chamfer
C0.2~0.3
L
φd
E7
φD
r6
1~2
1.6
1.6
I.D. O.D.
φd Tolerance φD Tolerance
Thickness
+0.020
+0.025
+0.025
+0.032
+0.032
+0.032
+0.040
+0.040
+0.032
+0.040
+0.040
+0.050
+0.050
+0.050
+0.061
+0.061
+0.004
+0.009
+0.006
+0.013
+0.013
+0.008
+0.016
+0.016
+0.016
+0.024
+0.021
+0.031
+0.031
+0.026
+0.037
+0.037
8
10
12
15
18
20
24
29
1.0
1.0
1.0
1.5
1.5
2.0
2.0
2.0
+0.028
+0.028
+0.034
+0.034
+0.034
+0.041
+0.041
+0.041
+0.019
+0.019
+0.023
+0.023
+0.023
+0.028
+0.028
+0.028
6
8
10
12
15
16
20
25
I.D. tolerance
after press
fitting (reference)
060808081008
mm 8
060810081010101210
10
060812081012101212121512151812162012
12
060815081015101215121515151815162015202415
15
060816081016101216121516151816162016202416252916
16
121520151820162020202420252920
20
162025202425252925
25
202430252930
30
Length L Tolerance-0.1-0.3
※The I.D. tolerance is reference value as press fitting into H7 housing.
212
Selection Guide
ProductInform
ationPlastic Bearing
Multi-layer Bearing
Metallic Bearing
Air Bearings
Technical Inform
ationSlide Shifter
Corporate Profi le
184-271_金属系ヘ�アリンク�.indd 212 19/10/17 19:45
Oiles 500HP Hard special copper alloy bearings with embedded solid lubricant
Features ●Bears higher loads than the 500SP5.●Demonstrates superior wear resistance under high-load and low-speed
applications.
Ser vice range 500HP SL1Lubrication condition
Service temperature range ℃Allowable max. pressure P N/mm2{kgf/cm2}
Allowable max. velocity V m/s{m/min}
Allowable max. PV value N/mm2・m/s{kgf/cm2・m/min}
Dry
0.10{6}
1.65{1,010}
-40~+150
73(180){745(1,837)}
periodic lubrication
0.25{15}
3.25{1,990}
The values in parentheses are stat ic bearing pressures, which are the bearing pressures in appl ica t ions wi th no mot ion or very smal l mot ion (≦0.0017m/s[0.1m/min]).
※Above values are applicable when solid lubricants SL1 are used.
Density
Tensile strength
Tensile elongation at break
Compressive strength
Hardness
Modulus of longitudinal elasticity.
Co-efficient of linear expansion
JIS Z 2241
JIS Z 2241
JIS Z 2243
7.6
540{55}
0.3
490{50}(Note)
245
127,000{13,000}
1.8
Mechanical proper tiesg/cm3
N/mm2{kgf/mm2}
%
N/mm2{kgf/mm2}
HBW
N/mm2{kgf/mm2}
×10-5 ℃-1
※The values shown above are typical values, not the standard values.(Note)Compressive strength is 0.2%
Solid lubricant, SL401 and SL403 are not lead-free.
Please indicate the type of motion (rotation, reciprocating, rotation & reciprocating) for custom-made products.
213
Sele
ctio
n G
uide
Prod
uct
Info
rmat
ion
Plas
tic B
earin
gM
ulti-
laye
r Bea
ring
Met
allic
Bea
ring
Air
Bear
ings
Tech
nica
l In
form
atio
nSl
ide
Shift
erCo
rpor
ate
Profi
le
184-271_金属系ヘ�アリンク�.indd 213 19/10/17 19:45
HPB Oiles 500HP SL1 Bushings
I.D. O.D.
φd Tolerance φD Tolerance
20202025253030404050506060
30303035354040505060607575
+0.061
+0.061
+0.061
+0.061
+0.061
+0.061
+0.061
+0.075
+0.075
+0.075
+0.075
+0.090
+0.090
+0.040
+0.040
+0.040
+0.040
+0.040
+0.040
+0.040
+0.050
+0.050
+0.050
+0.050
+0.060
+0.060
+0.041
+0.041
+0.041
+0.050
+0.050
+0.050
+0.050
+0.050
+0.050
+0.060
+0.060
+0.062
+0.062
+0.028
+0.028
+0.028
+0.034
+0.034
+0.034
+0.034
+0.034
+0.034
+0.041
+0.041
+0.043
+0.043
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
Part No.
HPB-203020HPB-203025HPB-203030HPB-253520HPB-253530HPB-304030HPB-304040HPB-405040HPB-405050HPB-506050HPB-506060HPB-607550HPB-607560
Length
L Tolerance
20253020303040405050605060
Motiondirection
Mating shaft Bushing Housing
H7
φdφD
Shaftd8: For general use (High-load)e7: For general use (Low-load)f7: For high accuracy use
L
1.6( )
Sh
aft
chamfer
6.3( )
15°
10°
R1.5~2
C0.5~1
L
2.5~4.5
φdE7
φDr6
2~4
+0.037
+0.037
+0.037
+0.030
+0.030
+0.032
+0.032
+0.046
+0.046
+0.045
+0.045
+0.053
+0.053
+0.016
+0.016
+0.016
+0.009
+0.009
+0.011
+0.011
+0.021
+0.021
+0.020
+0.020
+0.023
+0.023
※The I.D. tolerance after press fitting is for reference only.
Part No.
Specify Part No. by required I.D., O.D. and Length.
(e.g.) I.D. is 30mm, O.D. is 40mm, and length is 40mm.
HPB - 304040
1.6
1.6
I.D. tolerance
after press
fitting (reference)
The dimensional tolerances are the values measured at +25℃.
214
Selection Guide
ProductInform
ationPlastic Bearing
Multi-layer Bearing
Metallic Bearing
Air Bearings
Technical Inform
ationSlide Shifter
Corporate Profi le
184-271_金属系ヘ�アリンク�.indd 214 19/10/17 19:45
Oiles 500AB Aluminum bronze bearings with embedded solid lubricant
※The values shown above are typical values, not the standard values.(Note)Compressive strength is 0.2%
Features●Usable in seawater.●Has superior heat resistance.●Not brittle at low temperatures and may be used at very low temperatures.
The values in parentheses are static bearing pressures, which are the bearing pressures in applications with no motion or very small motion (≦0.0017m/s[0.1m/min]).
※Above values are applicable when solid lubricants SL1 are used.When you use standard #500AB series in the temperature and over, contact us for more information.
Ser vice range 500AB SL1Lubrication condition
Service temperature range ℃Allowable max. pressure P N/mm2{kgf/cm2}
Allowable max. velocity V m/s{m/min}
Allowable max. PV value N/mm2・m/s{kgf/cm2・m/min}
Dry
-250~+400
0.25{15}
1.25{765}
24(100){245(1,020)}
periodic lubrication
-40~+150
0.50{30}
2.45{1,500}
Density
Tensile strength
Tensile elongation at break
Compressive strength
Impact strength
Hardness
Modulus of longitudinal elasticity
Co-efficient of linear expansion
Thermal conductivity
JIS Z 2241
JIS Z 2241
JIS Z 2242
JIS Z 2243
7.6
590{60}
15
240{24}(Note)
25{2.5}
160
108,000{11,000}
1.6
58.6{0.14}
Mechanical proper tiesg/cm3
N/mm2{kgf/mm2}
%
N/mm2{kgf/mm2}
J/cm2{kgfm/cm2}
HBW
N/mm2{kgf/mm2}
×10-5 ℃-1
W/m℃{cal/sec℃cm}
Please indicate the type of motion (rotation, reciprocating, rotation & reciprocating) for custom-made products.
Solid lubricant, SL401 and SL403 are not lead-free.
215
Sele
ctio
n G
uide
Prod
uct
Info
rmat
ion
Plas
tic B
earin
gM
ulti-
laye
r Bea
ring
Met
allic
Bea
ring
Air
Bear
ings
Tech
nica
l In
form
atio
nSl
ide
Shift
erCo
rpor
ate
Profi
le
184-271_金属系ヘ�アリンク�.indd 215 19/10/17 19:45
Test data
W
W
Journal oscillation test in sea water<Testing conditions>Mating material : SUS304Pressure : 15.7N/mm2{160.0kgf/cm2}Oscillating cycle : 60cpmOscillating angle : ±10°Test cycle(time) : 100,000cycle(27.8hrs.)Ambience : in artificial sea water temperature 20±5°*SL4 is used for this test data.
Journal oscillation test in water<Testing conditions>Bearing dimension : φ80×φ100×R60Mating material : S45C hard chrome platingPressure : 19.6N/mm2{200.0kgf/cm2} 29.4N/mm2{300.0kgf/cm2}Velocity : 0.004m/s{0.25m/min}Oscillating cycle : 6cpmOscillating angle : ±15°Test cycle(time) : 100,000cycle(278hrs.)Ambience : in the purified waterLubrication : SL4L coating
Oscillation cycle〔×102〕
0.20
0.15
0.10
0.05
00 20 40 60 80 100
Coefficient of friction〔μ〕
0.20
0.15
0.10
0.05
0200 40 60 80 100
Oscillation cycle〔×103〕
Oiles 500AB-SL4(29.4N/mm2{300.0kgf/cm2})Wear amount : 0.022mm
Oiles 500AB-SL4(19.6N/mm2{200.0kgf/cm2})Wear amount : 0.017mm
Coefficient of friction〔μ〕
216
Selection Guide
ProductInform
ationPlastic Bearing
Multi-layer Bearing
Metallic Bearing
Air Bearings
Technical Inform
ationSlide Shifter
Corporate Profi le
184-271_金属系ヘ�アリンク�.indd 216 19/10/17 19:45
Oiles 500B Bronze bearings with embedded solid lubricant
Feature●Serviceable without the need for lubrication.●Demonstrates high performance under middle-load and middle-speed
operations.●Usable at high temperatures.●Has superior chemical and corrosion resistances.●Standard products are available in various sizes.
Service range 500B 1 SL2Lubrication condition
Service temperature range ℃Allowable max. pressure P N/mm2{kgf/cm2}
Allowable max. velocity V m/s{m/min}
Allowable max. PV value N/mm2・m/s{kgf/cm2・m/min}
Dry
-40~+250
0.40{24}
1.00{612}
15(49.0){153(500)}
periodic lubrication
-40~+150
0.85{51}
1.65{1,010}
※The values shown above are typical values, not the standard values.(Note)Compressive strength is 0.2%
The values in parentheses are static bearing pressures, which are the bearing pressures in applications with no motion or very small motion (≦0.0017m/s[0.1m/min]).
※Above values are applicable when solid lubricants SL2 are used.
Density
Tensile strength
Tensile elongation at break
Compressive strength
Impact strength
Hardness
Modulus of longitudinal elasticity
Co-efficient of linear expansion
Thermal conductivity
JIS Z 2241
JIS Z 2241
JIS Z 2242
JIS Z 2243
8.8
195{20}
15
95{9.5}(Note1)
10{1}
60
83,000{8,500}
1.8
71.1{0.17}
8.7
245{25}
15
130{13}(Note)
70
103,000{10,500}
2.0
75.3{0.18}
Mechanical properties 500B 1 500B 2
g/cm3
N/mm2{kgf/mm2}
%
N/mm2{kgf/mm2}
J/cm2{kgfm/cm2}
HBW
N/mm2{kgf/mm2}
×10-5 ℃-1
W/m℃{cal/sec℃cm}
Please indicate the type of motion (rotation, reciprocating, rotation & reciprocating) for custom-made products.
Base metal contains lead.
217
Sele
ctio
n G
uide
Prod
uct
Info
rmat
ion
Plas
tic B
earin
gM
ulti-
laye
r Bea
ring
Met
allic
Bea
ring
Air
Bear
ings
Tech
nica
l In
form
atio
nSl
ide
Shift
erCo
rpor
ate
Profi
le
184-271_金属系ヘ�アリンク�.indd 217 19/10/17 19:45
Relief angle
Rake angle
Nose radius (mm)
Speed (m/min)
Cut depth (mm)
Feed (mm/rev)
carbide tool(JIS)
5~10゜
2~5゜
0.40~0.80
100~200
0.05~0.30
0.08~0.30
Lathe turning
Cu
ttin
g t
ool
Con
dit
ion
I.D.
class 7 to 8
O.D.
class 6 to 7
Length
class 8 to 9
Machining accuracy (bushing)
Classes here are in JIS standard.
This product demonstrates satisfactory p e r f o r m a n c e a t t h e s l i d e s u r f a c e roughness of Rz6.3 to 12.5μm.
Apply sol id lubricant or grease to the sliding surface after machining.
500B 1 Test data
W
Journal rotational load resistance test<Testing conditions>
Mating material : S45C
Pressure : 0.98N/mm2{10.0kgf/cm2} is loaded incrementally per 10minutes
Velocity : 0.083m/s{5.0m/min}
Lubrication : dry 0 2.0{20}
3.9{40}
5.9{60}
7.8{80}
9.8{100}
11.8{120}
13.7{140}
15.7{160}
Coefficient of friction〔μ〕
Bearing temperature 〔℃〕0.40
0.30
0.20
0.10
0
150
100
50
Contact pressure〔 〕N/mm2{kgf/cm2}
Bearing temperature
Co-efficient of friction
218
Selection Guide
ProductInform
ationPlastic Bearing
Multi-layer Bearing
Metallic Bearing
Air Bearings
Technical Inform
ationSlide Shifter
Corporate Profi le
184-271_金属系ヘ�アリンク�.indd 218 19/10/17 19:45
BCB Oiles 500B1 SL2 Bushings
I.D. O.D.
φd Tolerance φD Tolerance
2025303032323535404045455050555560606565707075758080858590909595100100
30354042424545485055556060657075758080858590909595100100105110115115120120125
+0.105
+0.105
+0.105
+0.105
+0.144
+0.144
+0.144
+0.144
+0.144
+0.144
+0.144
+0.144
+0.144
+0.144
+0.190
+0.190
+0.190
+0.190
+0.190
+0.190
+0.190
+0.190
+0.190
+0.190
+0.190
+0.190
+0.242
+0.242
+0.242
+0.242
+0.242
+0.242
+0.242
+0.242
+0.072
+0.072
+0.072
+0.072
+0.105
+0.105
+0.105
+0.105
+0.105
+0.105
+0.105
+0.105
+0.105
+0.105
+0.144
+0.144
+0.144
+0.144
+0.144
+0.144
+0.144
+0.144
+0.144
+0.144
+0.144
+0.144
+0.188
+0.188
+0.188
+0.188
+0.188
+0.188
+0.188
+0.188
+0.049
+0.059
+0.059
+0.059
+0.059
+0.059
+0.059
+0.059
+0.059
+0.071
+0.071
+0.071
+0.071
+0.071
+0.073
+0.073
+0.073
+0.073
+0.073
+0.086
+0.086
+0.086
+0.086
+0.086
+0.086
+0.086
+0.086
+0.089
+0.089
+0.089
+0.089
+0.089
+0.089
+0.103
+0.028
+0.034
+0.034
+0.034
+0.034
+0.034
+0.034
+0.034
+0.034
+0.041
+0.041
+0.041
+0.041
+0.041
+0.043
+0.043
+0.043
+0.043
+0.043
+0.051
+0.051
+0.051
+0.051
+0.051
+0.051
+0.051
+0.051
+0.054
+0.054
+0.054
+0.054
+0.054
+0.054
+0.063
20 25 30 40 50 60
203025
304025304225
203020253520
203030253530304030304230324230324530354530354830405030405530
253540304040304240324240324540354540354840405040405540455540456040506040506540
354550354850405050405550455550456050506050506550557050557550607550608050
506060506560557060557560607560608060658060658560708560709060759060759560809560
8010060
Length L Tolerance 0-0.2
1.6( )
h7
Mating shaft Bushing Housing
L
φdφD
Motiondirection
6.3( )
chamfer
H7
※The I.D. tolerance after press fitting is for reference only.
Part No.
Specify Part No. by required I.D., O.D. and Length.
(e.g.) I.D. is 60mm, O.D. is 75mm, and length is 50mm.
BCB - 607550
The dimensional tolerances are the values measured at +25℃.
219
Sele
ctio
n G
uide
Prod
uct
Info
rmat
ion
Plas
tic B
earin
gM
ulti-
laye
r Bea
ring
Met
allic
Bea
ring
Air
Bear
ings
Tech
nica
l In
form
atio
nSl
ide
Shift
erCo
rpor
ate
Profi
le
184-271_金属系ヘ�アリンク�.indd 219 19/10/17 19:45
80 100 120
607580608080658080658580708580709080759080759580809580
8010080851008085105809011080901158095115809512080
1001208010012580
809510080100100851001008510510090110100901151009511510095120100
100120100100125100
100120120100125120
I.D.
φd
2025303032323535404045455050555560606565707075758080858590909595100100
+0.077
+0.071
+0.071
+0.071
+0.110
+0.110
+0.110
+0.110
+0.110
+0.103
+0.103
+0.103
+0.103
+0.103
+0.147
+0.147
+0.147
+0.147
+0.147
+0.139
+0.139
+0.139
+0.139
+0.139
+0.139
+0.139
+0.191
+0.188
+0.188
+0.188
+0.188
+0.188
+0.188
+0.179
+0.044
+0.038
+0.038
+0.038
+0.071
+0.071
+0.071
+0.071
+0.071
+0.064
+0.064
+0.064
+0.064
+0.064
+0.101
+0.101
+0.101
+0.101
+0.101
+0.093
+0.093
+0.093
+0.093
+0.093
+0.093
+0.093
+0.137
+0.134
+0.134
+0.134
+0.134
+0.134
+0.134
+0.125
Length L Tolerance 0-0.2
0.3~1.215°
2~5
2~8
φd
φDr7
L
1.6
6.3
I.D. tolerance
after press
fitting (reference)
●Both ends have the same chamfering.
●Applicable to rotation and oscillating motion.
●Do not remove lubricant applied to the inner surface of the product. Otherwise, the product will not demonstrate its performance.
220
Selection Guide
ProductInform
ationPlastic Bearing
Multi-layer Bearing
Metallic Bearing
Air Bearings
Technical Inform
ationSlide Shifter
Corporate Profi le
184-271_金属系ヘ�アリンク�.indd 220 19/10/17 19:45
Oiles 500F Cast iron bearings with embedded solid lubricant
Feature●Serviceable without the need for lubrication.●Demonstrates high performance under low- and middle-load, low-speed operations.●Demonstrates superior wear resistance in applications where oil film is seldom
produced such as reciprocating motions, oscillation, frequent starts and stops, etc.●Lower prices than the bearings with copper alloy bases.●Standard products are available in various sizes.
Ser vice range 500F SL1Lubrication condition
Service temperature range ℃Allowable max. pressure P N/mm2{kgf/cm2}
Allowable max. velocity V m/s{m/min}
Allowable max. PV value N/mm2・m/s{kgf/cm2・m/min}
Dry
-40~+400
5(73.5){51(750)}
0.15{9}
0.50{306}
periodic lubrication
-40~+150
8(73.5){82(750)}
0.25{15}
0.80{490}
Relief angle
Rake angle
Nose radius (mm)
Speed (m/min)
Cut depth (mm)
Feed (mm/rev)
carbide tool(JIS)
5~10゜
2~5゜
0.40~0.80
100~200
0.05~0.30
0.08~0.30
Lathe turning
Cu
ttin
g t
ool
Con
dit
ion
I.D.
class 7 to 8
O.D.
class 6 to 7
Length
class 8 to 9
Machining accuracy (bushing)
Classes here are in JIS standard.
This product demonstrates satisfactory performance at the slide surface roughness of Rz6.3 to 12.5μm.
※The values shown above are typical values, not the standard values.
The values in parentheses are stat ic bearing pressures, which are the bearing pressures in appl ica t ions wi th no mot ion or very smal l mot ion (≦0.0017m/s[0.1m/min]).
Apply solid lubricant or grease to the sliding surface after machining.
※Contact us for grinding and milling information.
When you use standard 500F series in the temperature of 150℃ and over, contact us for more information.
Please indicate the type of motion (rotation, reciprocating, rotation & reciprocating) for custom-made products.
Solid lubricant, SL401 and SL403 are not lead-free.
Density
Tensile strength
Compressive strength
Impact strength
Hardness
Modulus of longitudinal elasticity
Co-efficient of linear expansion
Thermal conductivity
JIS Z 2241
JIS Z 2242
JIS Z 2243
7.3
250{26}
740{75}
4{0.4}
190
107,800{11,000}
1.2
50.2{0.12}
7.1
150{15}
440{45}
1{0.1}
160
78,000{8,000}
1.2
50.2{0.12}
Mechanical proper ties 500F1 500F2
g/cm3
N/mm2{kgf/mm2}
N/mm2{kgf/mm2}
J/cm2{kgfm/cm2}
HBW
N/mm2{kgf/mm2}
×10-5 ℃-1
W/m℃{cal/sec℃cm}
Standard product / Custom-made product
221
Sele
ctio
n G
uide
Prod
uct
Info
rmat
ion
Plas
tic B
earin
gM
ulti-
laye
r Bea
ring
Met
allic
Bea
ring
Air
Bear
ings
Tech
nica
l In
form
atio
nSl
ide
Shift
erCo
rpor
ate
Profi
le
184-271_金属系ヘ�アリンク�.indd 221 19/10/17 19:45
Test data
W
Reciprocation test<Testing conditions>
Bearing dimension : □40×□40×t20
Mating material : FC250 ground
Pressure : 5.9N/mm2{60.0kgf/cm2}
Velocity : 0.12m/s{7.0m/min}
Stroke : 80mm
Test cycle : 100,000cycle
Lubrication : initial grease applied
0.04
0.03
0.02
0.01
00 20 40 60 80 100
Wear amount〔mm〕
Reciprocation cycle〔×102〕
P=5.9N/mm2{60.0kgf/cm2}
222
Selection Guide
ProductInform
ationPlastic Bearing
Multi-layer Bearing
Metallic Bearing
Air Bearings
Technical Inform
ationSlide Shifter
Corporate Profi le
184-271_金属系ヘ�アリンク�.indd 222 19/10/17 19:45
FGB Oiles 500F SL1 Guide Bushings
●500F, is used as base steel.
●Applicable to reciprocating motion.
●It is recommended to use a set screw to
prevent dislocation.
Part No.
Specify Part No. by required I.D., O.D. and Length.
(e.g.) I.D. is 60mm, O.D. is 80mm, and length is 90mm.
FGB - 608090
Motion direction Bushing
L
φdφD
Housing
H7
chamfer
6.3( )
C0.5C1
C2
C1R20
φdH7
φDjs6
Lℓ2 ℓ1
0.5
1.6
1.6
15°
Part No.I.D. O.D.
φd Tolerance φD Tolerance
2530354040506080100120
40506060607080100120140
±0.008
±0.008
±0.0095
±0.0095
±0.0095
±0.0095
±0.0095
±0.011
±0.011
±0.0125
Length
L Tolerance
40505555607590120150180
+0.021
+0.021
+0.025
+0.025
+0.025
+0.025
+0.030
+0.030
+0.035
+0.035
0
0
0
0
0
0
0
0
0
0
ℓ1 ℓ2
10101515101520252525
555551010101010
FGB-254040FGB-305050FGB-356055FGB-406055FGB-406060FGB-507075FGB-608090FGB-80100120FGB-100120150FGB-120140180
-0.2
-0.2
-0.2
-0.2
-0.2
-0.2
-0.2
-0.2
-0.2
-0.2
0
0
0
0
0
0
0
0
0
0
The dimensional tolerances are the values measured at +25℃.
223
Sele
ctio
n G
uide
Prod
uct
Info
rmat
ion
Plas
tic B
earin
gM
ulti-
laye
r Bea
ring
Met
allic
Bea
ring
Air
Bear
ings
Tech
nica
l In
form
atio
nSl
ide
Shift
erCo
rpor
ate
Profi
le
184-271_金属系ヘ�アリンク�.indd 223 19/10/17 19:45
FWPT Oiles 500F SL1 Wear Plates
●500F, is used as base steel.
Specify Part No. by required width and length.
(e.g.) Width is 100mm and length is 100mm.
Motion direction
Part No.FWPT - 100100
L
T
W
T
φ17.5
φ11
8 C3 all circumferences
6
2
R10 all circumferencesG
1.6
6.3
Part No. TW20202020202020202020202020
ℓ1 ℓ2L100125150200250125150200250150200250300
100100100100100125125125125150150150150
507510015020075100150200100150200250
25252525252525252525252525
2222222222222
AAAAAAAAAAAAA
±0.01
±0.01
±0.01
±0.01
±0.01
±0.01
±0.01
±0.01
±0.01
±0.01
±0.01
±0.01
±0.01
±0.2
±0.2
±0.2
±0.2
±0.2
±0.2
±0.2
±0.2
±0.2
±0.2
±0.2
±0.2
±0.2
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
FWPT-100100FWPT-100125FWPT-100150FWPT-100200FWPT-100250FWPT-125125FWPT-125150FWPT-125200FWPT-125250FWPT-150150FWPT-150200FWPT-150250FWPT-150300
4-C1ℓ1ℓ2 ℓ2
L
W
Cross-section Chamfering
Type A
Width Length Thickness Mounting hole intenvalsChamfering
Tolerance Tolerance Tolerance Tolerance
Attach bolts
Type QtyM10 Hexagonsocket head
M10 Hexagonsocket head
M10 Hexagonsocket head
M10 Hexagonsocket head
M10 Hexagonsocket head
M10 Hexagonsocket head
M10 Hexagonsocket headM10 Hexagonsocket head
M10 Hexagonsocket head
M10 Hexagonsocket head
M10 Hexagonsocket head
M10 Hexagonsocket head
M10 Hexagonsocket head
224
Selection Guide
ProductInform
ationPlastic Bearing
Multi-layer Bearing
Metallic Bearing
Air Bearings
Technical Inform
ationSlide Shifter
Corporate Profi le
184-271_金属系ヘ�アリンク�.indd 224 19/10/17 19:45
FWP Oiles 500F SL1 Wear Plates
4-C1ℓ1ℓ2 ℓ2
L
WW1
W2
W2
4-C1ℓ1ℓ1ℓ2 ℓ2
LW
4-C1ℓ1ℓ2 ℓ2
L
W
●500F, is used as base steel.
●Motion directions for FWP-4875 to FWP-200300 are width and length.
●Motion directions for FWP-2875 to FWP-38200 are length direction only.
Part No.ThicknessWidth
T ToleranceW
202020202020202020202020202020202020202020
ℓ1 ℓ2
Length
L
75100125150200751001251502007510012515020020025075100125150
Tolerance Tolerance Tolerance
282828282838383838384848484848484858585858
Mounting hole intervals
455075100
455075100
455075100100150100455075100
152525252515252525251525252550252515252525
150
150
222222222222222232222
CCCCCCCCCCBBBBBBBBBBB
±0.01
±0.01
±0.01
±0.01
±0.01
±0.01
±0.01
±0.01
±0.01
±0.01
±0.01
±0.01
±0.01
±0.01
±0.01
±0.01
±0.01
±0.01
±0.01
±0.01
±0.01
Chamfering
±0.2
±0.2
±0.2
±0.2
±0.2
±0.2
±0.2
±0.2
±0.2
±0.2
±0.2
±0.2
±0.2
±0.2
±0.2
±0.2
±0.2
±0.2
±0.2
±0.2
±0.2
-0.3-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
FWP-2875FWP-28100FWP-28125FWP-28150FWP-28200FWP-3875FWP-38100FWP-38125FWP-38150FWP-38200FWP-4875FWP-48100FWP-48125FWP-48150FWP-48200FWP-48200AFWP-48250FWP-5875FWP-58100FWP-58125FWP-58150
Part No.
Specify Part No. by required width and length.
(e.g.) Width is 58mm and length is 100mm.
FWP - 58100
Motion direction
L
T
W
Attach bolts
Type QtyM10 Hexagonsocket head
M10 Hexagonsocket head
M10 Hexagonsocket head
M10 Hexagonsocket head
M10 Hexagonsocket head
M10 Hexagonsocket head
M10 Hexagonsocket head
M10 Hexagonsocket head
M10 Hexagonsocket head
M10 Hexagonsocket head
M10 Hexagonsocket head
M10 Hexagonsocket head
M10 Hexagonsocket head
M10 Hexagonsocket head
M10 Hexagonsocket head
M10 Hexagonsocket head
M10 Hexagonsocket head
M10 Hexagonsocket head
M10 Hexagonsocket head
M10 Hexagonsocket head
M10 Hexagonsocket head
225
Sele
ctio
n G
uide
Prod
uct
Info
rmat
ion
Plas
tic B
earin
gM
ulti-
laye
r Bea
ring
Met
allic
Bea
ring
Air
Bear
ings
Tech
nica
l In
form
atio
nSl
ide
Shift
erCo
rpor
ate
Profi
le
184-271_金属系ヘ�アリンク�.indd 225 19/10/17 19:45
Part No.ThicknessWidth
T ToleranceW
202020202020202020202020202020202020202020
W1 W2 ℓ1 ℓ2
Length
L
75100125150200100125150200250125125150200250150200250200250300
Tolerance Tolerance Tolerance Tolerance
7575757575100100100100100125125125125125150150150200200200
Mounting hole intervals
25507510015050751001502007575100150200100150200150200250
252525252525252525252525252525252525252525
50505050507550505050100100100150150150
25 252525252537.537.537.537.5252525252525
222224444444444444444
AAAAAAAAAAAAAAAAAAAAA
±0.01
±0.01
±0.01
±0.01
±0.01
±0.01
±0.01
±0.01
±0.01
±0.01
±0.01
±0.01
±0.01
±0.01
±0.01
±0.01
±0.01
±0.01
±0.01
±0.01
±0.01
Chamfering
±0.2
±0.2
±0.2
±0.2
±0.2
±0.2
±0.2
±0.2
±0.2
±0.2
±0.2
±0.2
±0.2
±0.2
±0.2
±0.2
±0.2
±0.2
±0.2
±0.2
±0.2
±0.2
±0.2
±0.2
±0.2
±0.2
±0.2
±0.2
±0.2
±0.2
±0.2
±0.2
±0.2
±0.2
±0.2
±0.2
±0.2
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
FWP-7575BFWP-75100BFWP-75125FWP-75150FWP-75200FWP-100100FWP-100125FWP-100150FWP-100200FWP-100250FWP-125125FWP-125125AFWP-125150FWP-125200FWP-125250FWP-150150FWP-150200FWP-150250FWP-200200FWP-200250FWP-200300
T
φ17.5
φ11
8
2
3.5
2
3.56
2
Cross-section Chamfering
Type A Type B Type C
G1.6
6.3
R10 allcircumferences
R5 allcircumferences
R5 allcircumferences
C3 allcircumferences
C3 allcircumferences
C1 allcircumferences
Attach bolts
Type QtyM10 Hexagonsocket head
M10 Hexagonsocket head
M10 Hexagonsocket head
M10 Hexagonsocket head
M10 Hexagonsocket head
M10 Hexagonsocket head
M10 Hexagonsocket head
M10 Hexagonsocket head
M10 Hexagonsocket head
M10 Hexagonsocket head
M10 Hexagonsocket head
M10 Hexagonsocket head
M10 Hexagonsocket head
M10 Hexagonsocket head
M10 Hexagonsocket head
M10 Hexagonsocket head
M10 Hexagonsocket head
M10 Hexagonsocket head
M10 Hexagonsocket head
M10 Hexagonsocket head
M10 Hexagonsocket head
226
Selection Guide
ProductInform
ationPlastic Bearing
Multi-layer Bearing
Metallic Bearing
Air Bearings
Technical Inform
ationSlide Shifter
Corporate Profi le
184-271_金属系ヘ�アリンク�.indd 226 19/10/17 19:45
Oiles 500SP1 Spherical Bearings Unit bearings
Feature●Conforms to the ISO Standard E type bearings. Compatible with them dimensionally. High precision.●The inner surface of the inner race is subject to sliding. The outer surface of the inner race bears self-aligning.●Applicable to higher loads than other self-lubricating spherical bearings.●Applicable to large oscillating angles in circumferential oscillating motion.●Serviceable without the need for lubrication. Features quite long service life.
Ser vice rangeLubrication condition
Service temperature range ℃Allowable max. pressure P N/mm2{kgf/cm2}
Allowable max. velocity V m/s{m/min}
Allowable max. PV value N/mm2・m/s{kgf/cm2・m/min}
Dry
-40~+150
39.2{400}
0.15{9}
0.80{490}
(Note 1) The allowable dynamic loads are calculated based on the allowable bearing pressure in oscillating motion, which is 39.2 N/mm2 [400 kgf/cm2]. They apply to the long-term loads under normal conditions.
(Note 2) The allowable static loads are calculated based on the allowable static bearing pressure 98.0 N/mm2 [1,000 kgf/cm2] (i.e., allowable bearing pressure when accompanied with no sliding or accompanied with sliding at quite low speed not more than 0.0017 m/s [0.1 m/min.]. They apply to the accidental short-term loads under abnormal conditions.
Part No. Allowable dynamic load (Note 1)
N{kgf}Allowable static load (Note 2)
N{kgf}
SPS-2035ESPS-2542ESPS-3047ESPS-3555ESPS-4062ESPS-4568ESPS-5075ESPS-6090ESPS-70105ESPS-80120ESPS-90130ESPS-100150ESPS-110160ESPS-120180E
9,410{ 960} 15,600{ 1,600} 21,100{ 2,160} 27,400{ 2,800} 34,500{ 3,520} 44,100{ 4,500} 54,900{ 5,600} 84,700{ 8,640}109,000{11,200}141,000{14,400}176,000{18,000}215,000{22,000}237,000{24,200}329,000{33,600}
23,500{ 2,400} 39,200{ 4,000} 52,900{ 5,400} 68,600{ 7,000} 86,200{ 8,800}109,000{11,200}137,000{14,000}211,000{21,600}274,000{28,000}353,000{36,000}441,000{45,000}539,000{55,000}593,000{60,500}823,000{84,000}
divided face
maximum load
The outer race is split into two parts.
Assemble them as shown below so
that the split parts are not located
at the maximum load point . the
bearing to fix it. Press it slowly with
a vice or press by the intermediation
of a as shown below. Chamfering the
housing end is more effective.
press-fit
housing
chamfer
mandrel
Example ofattachment
Bearing Fixing Method
※Above is the value when applying SL1 as solid lubricant.
227
Sele
ctio
n G
uide
Prod
uct
Info
rmat
ion
Plas
tic B
earin
gM
ulti-
laye
r Bea
ring
Met
allic
Bea
ring
Air
Bear
ings
Tech
nica
l In
form
atio
nSl
ide
Shift
erCo
rpor
ate
Profi
le
184-271_金属系ヘ�アリンク�.indd 227 19/10/17 19:45
SPS Oiles 500SP1 SL1 Spherical Bearings
Part No.
SPS-2035ESPS-2542ESPS-3047ESPS-3555ESPS-4062ESPS-4568ESPS-5075ESPS-6090ESPS-70105ESPS-80120ESPS-90130ESPS-100150ESPS-110160ESPS-120180E
I.D. O.D.
φd Tolerance φD Tolerance
2025303540455060708090100110120
3542475562687590105120130150160180
0
0
0
0
0
0
0
0
0
0
0
0
0
0
-0.011
-0.011
-0.011
-0.013
-0.013
-0.013
-0.013
-0.015
-0.015
-0.015
-0.018
-0.018
-0.018
-0.018
0
0
0
0
0
0
0
0
0
0
0
0
0
0
-0.24
-0.24
-0.24
-0.3
-0.3
-0.3
-0.3
-0.4
-0.4
-0.4
-0.5
-0.5
-0.5
-0.5
+0.021
+0.021
+0.021
+0.025
+0.025
+0.025
+0.025
+0.030
+0.030
+0.030
+0.035
+0.035
+0.035
+0.035
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Tolerance
1216182022252836404550555570
1620222528323544495560707085
B
3.55.05.06.06.06.06.06.07.07.07.07.08.08.0
hC
97667766665766
29 35.540.747 53 60 66 80 92 105 115 130 140 160
φSφd1
2429344045515667788998110121136
※φD toherance is nominal.
φS
(φd1)
Ch
B MoS2 coating
hardened SUJ2 outer race
(R0.6~1.8)R0.3~1.0
φdH7
φD
circumferential oscillatingmotion
divided face
1.6
1.6
Part No.
Specify Part No. by required I.D. and O.D.
(e.g.) I.D. is 50mm and O.D. is 75mm.
SPS - 5075 E
allo
wab
le a
lignm
ent a
ngle
θ°
θ°
●Mating shaft
For general: e7 (Recommended housing K7)
For high load: d8 (Recommended housing N7)
2.5~9.52.5~9.5
10°
inner race
Oiles 500SPI10°
The dimensional tolerances are the values measured at +25℃.
228
Selection Guide
ProductInform
ationPlastic Bearing
Multi-layer Bearing
Metallic Bearing
Air Bearings
Technical Inform
ationSlide Shifter
Corporate Profi le
184-271_金属系ヘ�アリンク�.indd 228 19/10/17 19:45
Oiles 2000 Sintered multi-layer bearings with dispersed solid lubricant
Feature●Dispersed solid lubricant allows motions in any direction and offers superior
performance for minute movements.●Serviceable without the need for lubrication.●Features superior load resistance, speed characteristics, and wear resistance.●Standard products and plates for additional machining are available in various
sizes.
The values in parentheses are static bearing pressures, which are the bearing pressures in applications with no motion or very small motion (≦0.0017m/s[0.1m/min]).
Ser vice rangeLubrication condition
Service temperature range ℃Allowable max. pressure P N/mm2{kgf/cm2}
Allowable max. velocity V m/s{m/min}
Allowable max. PV value N/mm2・m/s{kgf/cm2・m/min}
Dry
24.5(73.5){250(750)}
0.50{30}
1.63{1,000}
-40~+120
periodic lubrication
49(73.5){500(750)}
1.00{60}
2.45{1,500}
密度
硬さ
含油率
JIS Z 2245
6.3
HRM60~95
12
機械的性質g/cm3
vol%
Relief angle
Rake angle
Nose radius (mm)
Speed (m/min)
Cut depth (mm)
Feed (mm/rev)
carbide tool(JIS)
5~10゜
2~5゜
0.40~0.80
150~300
0.10~0.20
0.05~0.15
Lathe turning
Cu
ttin
g t
ool
Con
dit
ion
I.D.
class 7 to 8
O.D.
class 6 to 7
Length
class 8 to 9
Machining accuracy (bushing)
Classes here are in JIS standard.
This product demonstrates satisfactory performance at the slide surface roughness of Rz6.3 to 12.5μm.
Mach in ing cond i t i ons he re i nd ica te conditions for machining back metal or length. Do not machine sliding surface.
※Contact us for grinding and milling information.
※The value shown above are for sintered layer.※The values shown above are typical values, not the standard values.
Oil Impregnation Method
If the Oiles 2000 material is purchased and used by finishing it, it should be oil-impregnated after machining and then assembled in the housing. When the bearing is stored for long or washed, it should be oil-impregnated again and then assembled in the housing.For the method, see the description about the oil impregnation method shown on page 250.Dip the machined bearing in lubricating oil for 24 hours or more before using it, if oil impregnation (by heating) is disabled.
Density
Hardness
Oil impregnation rate
JIS K 7202-2
6.3
60~95
12
Mechanical proper tiesg/cm3
HRM
vol%
Standard product Plate for additional machining Custom-made product
229
Sele
ctio
n G
uide
Prod
uct
Info
rmat
ion
Plas
tic B
earin
gM
ulti-
laye
r Bea
ring
Met
allic
Bea
ring
Air
Bear
ings
Tech
nica
l In
form
atio
nSl
ide
Shift
erCo
rpor
ate
Profi
le
184-271_金属系ヘ�アリンク�.indd 229 19/10/17 19:45
Test data
W
W
Horizontal reciprocation test<Testing conditions>Bearing dimension : □40×□40×t20Mating material : FC250 ground Pressure : 5.9、11.8N/mm2{60.0、120.0kgf/cm2}Velocity : 0.12m/s{7.0m/min}Reciprocation cycle : 44cpmStroke : 80mmTest cycle : 100,000cycleLubrication : initial greasing at installation
Cam impact test<Testing conditions>Bearing dimension : □63×□95×t15Mating material : FC250 ground、 S45C quenched and groundPressure : 19.6N/mm2{200.0kgf/cm2}Velocity : 0.16m/s{9.6m/min}Impact frequency : 60cpmStroke : 80mmTest cycle : 500,000cycleLubrication : initial greasing at installation
Journal oscillation test<Testing conditions>Mating material : S35cw/gas nitriding SUS403 S35C/hard-chrme platingPressure : 24.5N/mm2{250.0kgf/cm2}Velocity : 0.002m/s{0.105m/min}Oscillating cycle : 10cpmOscillaing angle : ±5°Test cycle(time) : 100,000cycle(166.7hrs.)Lubrication : initial greasing at installation
0.04
0.03
0.02
0.01
00 20 40 60 80 100
Wear amount 〔mm〕
Reciprocation cycle〔×102〕
P=11.8N/mm2{120.0kgf/cm2}P=5.9N/mm2{60.0kgf/cm2}
10090807060504030201000 10 20 30 40 50 60 70 80 90 100
Bearing temperature〔℃〕
Oscillation cycle〔×103〕0.400.350.300.250.200.150.100.050C
oefficient of friction〔μ〕
Oscillation cycle〔×103〕0 10 20 30 40 50 60 70 80 90 100
S35C gas nitriding SUS403S35C hard-chrome plating
0.04
0.03
0.02
0.01
00 100 200 300 400 500
Wear amount 〔mm〕
Impact cycle〔×103〕
Mating material : S45C quenched and groundMating material : FC250 ground
230
Selection Guide
ProductInform
ationPlastic Bearing
Multi-layer Bearing
Metallic Bearing
Air Bearings
Technical Inform
ationSlide Shifter
Corporate Profi le
184-271_金属系ヘ�アリンク�.indd 230 19/10/17 19:45
CBB Oiles 2000 Bushings
I.D. O.D.
φd Tolerance φD Tolerance
1213141516182020252528303035354045455050505560606570707575808090100
181920212224283033353838404445505560606265707475808590909596100110120
+0.038
+0.042
+0.042
+0.042
+0.042
+0.042
+0.047
+0.047
+0.052
+0.052
+0.052
+0.052
+0.052
+0.060
+0.060
+0.060
+0.065
+0.065
+0.065
+0.065
+0.065
+0.072
+0.072
+0.072
+0.072
+0.077
+0.077
+0.077
+0.077
+0.077
+0.077
+0.085
+0.085
+0.049
+0.053
+0.053
+0.053
+0.053
+0.053
+0.060
+0.060
+0.065
+0.065
+0.065
+0.065
+0.065
+0.076
+0.076
+0.076
+0.081
+0.081
+0.081
+0.081
+0.081
+0.091
+0.091
+0.091
+0.091
+0.096
+0.096
+0.096
+0.096
+0.096
+0.096
+0.107
+0.107
+0.023
+0.028
+0.028
+0.028
+0.028
+0.028
+0.028
+0.028
+0.034
+0.034
+0.034
+0.034
+0.034
+0.034
+0.034
+0.034
+0.041
+0.041
+0.041
+0.041
+0.041
+0.043
+0.043
+0.043
+0.043
+0.051
+0.051
+0.051
+0.051
+0.051
+0.051
+0.054
+0.054
+0.034
+0.041
+0.041
+0.041
+0.041
+0.041
+0.041
+0.041
+0.050
+0.050
+0.050
+0.050
+0.050
+0.050
+0.050
+0.050
+0.060
+0.060
+0.060
+0.060
+0.060
+0.062
+0.062
+0.062
+0.062
+0.073
+0.073
+0.073
+0.073
+0.073
+0.073
+0.076
+0.076
10
121810131910142010152110162210182410202810
121812131912142012152112162212182412202812
253312
303812
121815131915142015152115162215182415202815203015253315253515
303815304015
405015
121816
152116162216182416202816203016253316253516
121819
162219
202819
121820131920142020152120162220182420202820203020253320253520283820303820304020354420354520405020
506020
121825131925142025152125162225182425202825203025253325253525283825303825304025354425354525405025
121830131930142030152130162230182430202830203030253330253530283830303830304030354430354530405030455530456030506030506230506530557030607430607530
708530
8
12180812 15 16 19 20 25 30
Length L Tolerance-0.1-0.3
Specify Part No. by required I.D., O.D. and Length.
(e.g.) I.D. is 35mm, O.D. is 44mm, and length
is 50mm. Part No.CBB - 354450
Motiondirection
Mating shaft Bushing Housing
Sh
aft
φd
φD r6
L
1.6( )
6.3( )
chamfer
H7
Shaft g6: For general use
f7: For high load use
The dimensional tolerances are the values measured at +25℃.
231
Sele
ctio
n G
uide
Prod
uct
Info
rmat
ion
Plas
tic B
earin
gM
ulti-
laye
r Bea
ring
Met
allic
Bea
ring
Air
Bear
ings
Tech
nica
l In
form
atio
nSl
ide
Shift
erCo
rpor
ate
Profi
le
184-271_金属系ヘ�アリンク�.indd 231 19/10/17 19:45
4035
162235
202835203035253335253535
303835304035354435354535405035455535
506035
607435607535
708535
162240182440202840203040253340253540283840303840304040354440354540405040455540456040506040506240506540557040607440607540658040708540
8096408010040
202850203050253350253550
303850304050354450354550405050455550456050506050506250506550557050607450607550658050708550709050759050
80965080100509011050
10012050
253360253560
303860304060354460354560405060455560456060506060506260506560557060607460607560658060708560709060759060
80966080100609011060
10012060
405070
456070506070506270506570557070607470607570658070708570709070759070
8096708010070
10012070
405080
456080506080
506580
607480607580658080708580709080759080759580809680
80100809011080
100120809011090
10012090
5065100
6075100
7085100
759010075951008096100
8010010090110100
100120100
80961208010012090110120
100120120
50 60 70 80 90 100 120
I.D. toleranceafter press
fitting (reference)
R2
10°
C0.3~1.01~4
R2
φd
φDr6
L
A
A
φ0.01◎
1.6
-0.3-0.1
Back metal
Sintered layer
(0.8mm or more)
+0.023
+0.023
+0.023
+0.023
+0.023
+0.022
+0.029
+0.029
+0.029
+0.029
+0.029
+0.029
+0.029
+0.037
+0.037
+0.037
+0.037
+0.040
+0.037
+0.039
+0.041
+0.045
+0.045
+0.045
+0.045
+0.045
+0.048
+0.045
+0.048
+0.046
+0.048
+0.054
+0.054
+0.034
+0.034
+0.034
+0.034
+0.034
+0.033
+0.042
+0.042
+0.042
+0.042
+0.042
+0.042
+0.042
+0.053
+0.053
+0.053
+0.053
+0.056
+0.053
+0.055
+0.057
+0.064
+0.064
+0.064
+0.064
+0.064
+0.067
+0.064
+0.067
+0.065
+0.067
+0.076
+0.076
●Press fitting is possible.
●Falling out or dislocation prevention is not
required.
Length L Tolerance-0.1-0.3
232
Selection Guide
ProductInform
ationPlastic Bearing
Multi-layer Bearing
Metallic Bearing
Air Bearings
Technical Inform
ationSlide Shifter
Corporate Profi le
184-271_金属系ヘ�アリンク�.indd 232 19/10/17 19:45
CLB Oiles 2000 Bushings (High Precision type)
I.D. O.D.
φd Tolerance φD Tolerance
1216202530354050607080100
1822283338445062748596120
+0.003
+0.003
+0.004
+0.004
+0.004
+0.005
+0.005
+0.005
+0.006
+0.006
+0.006
+0.007
+0.011
+0.011
+0.013
+0.013
+0.013
+0.016
+0.016
+0.016
+0.019
+0.019
+0.019
+0.022
-0.008
-0.009
-0.009
-0.011
-0.011
-0.011
-0.011
-0.013
-0.013
-0.015
-0.015
-0.015
0
0
0
0
0
0
0
0
0
0
0
0
20
162220202820
16
121816162216
25
121825
253325
30
162230202830253330303830
40
202840253340303840354440405040
50
253350303850354450405050506250607450708550809650
10012050
60
303860354460405060
607460
80
506280607480
809680
100
7085100
100120100
120
8096120100120120
Length L Tolerance 0-0.3
Motiondirection
Mating shaft Bushing Housing
g6(h6)
φdφD
L
0.8( )
6.3( )
chamfer
H6
R2
C0.5
R2
C0.5φd
φDh5
L
Part No.
Specify Part No. by required I.D., O.D. and Length.
(e.g.) I.D. is 35mm, O.D. is 44mm, and length is 50mm.
CLB - 354450
A
A
0.01○
φ0.005◎
G 1.6
Back metal
Sintered layer
(0.8mm or more)
By the combination of the highly precise article, clearance of a mating shaft and the bearings become smaller than normal combination.When use under the foreign matter environment ,or operating frequency are high, please contact us.The dimensional tolerances are the values measured at +25℃.
233
Sele
ctio
n G
uide
Prod
uct
Info
rmat
ion
Plas
tic B
earin
gM
ulti-
laye
r Bea
ring
Met
allic
Bea
ring
Air
Bear
ings
Tech
nica
l In
form
atio
nSl
ide
Shift
erCo
rpor
ate
Profi
le
184-271_金属系ヘ�アリンク�.indd 233 19/10/17 19:45
CLF Oiles 2000 Flange Bushings (High Precision type)
I.D. O.D. Flange
φd Tolerance φD Tolerance φF t Tolerance 4030 120100806050
20253035405060
-0.009
-0.011
-0.011
-0.011
-0.011
-0.013
-0.013
0
0
0
0
0
0
0
28333844506274
77710101010
38434854607284
+0.05
+0.05
+0.05
+0.05
+0.05
+0.05
+0.05
0
0
0
0
0
0
0
Tolerance
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.2
-0.2
-0.2
-0.2
-0.2
-0.2
-0.2
+0.004
+0.004
+0.004
+0.005
+0.005
+0.005
+0.006
+0.013
+0.013
+0.013
+0.016
+0.016
+0.016
+0.019
203025303030
2040
35404040
2550
5050
3060
6060
35804080
5010060120
Length L Tolerance 0-0.3
Flange bushing Housing
t
φF
Mating shaft
L
φdφD
g6(h6)
0.8( )
6.3( )
chamfer
H6
3
0.5
R2
C0.5
R2
C0.5C0.5
φF
L t
Part No.
Specify Part No. by required I.D. and Length.
(e.g.) I.D. is 30mm and length is 60mm.
CLF - 3060
φd
φDh5
A
A
0.01○
φ0.005◎
G1.6G 1.6
Motiondirection
Back metal
Sintered layer
(0.8mm or more)
R1.5
By the combination of the highly precise article, clearance of a mating shaft and the bearings become smaller than normal combination.When use under the foreign matter environment ,or operating frequency are high, please contact us.
●As for the flange root undercut shape, the
shape shown below is also available in
addition to that shown in the dimensional
drawing on the right.
2
30°
0.5R0.5 or less
(1.13)
The dimensional tolerances are the values measured at +25℃.
234
Selection Guide
ProductInform
ationPlastic Bearing
Multi-layer Bearing
Metallic Bearing
Air Bearings
Technical Inform
ationSlide Shifter
Corporate Profi le
184-271_金属系ヘ�アリンク�.indd 234 19/10/17 19:45
CWT Oiles 2000 Wear Plates 5mm Thickness
●Dedicated hexagon socket flat head bolts are
attached.
ThicknessWidth
Part No.T ToleranceW
5555555555555555
ℓ1 ℓ2
Length
L
5075100150507510015050751001505075100150
Tolerance Tolerance Tolerance
22222222282828283838383848484848
Mounting hole intervalsNo.
of holes
20457060204570602045706020457060
15151515151515151515151515151515
2223222322232223
±0.015
±0.015
±0.015
±0.015
±0.015
±0.015
±0.015
±0.015
±0.015
±0.015
±0.015
±0.015
±0.015
±0.015
±0.015
±0.015
±0.2
±0.2
±0.2
±0.2
±0.2
±0.2
±0.2
±0.2
±0.2
±0.2
±0.2
±0.2
±0.2
±0.2
±0.2
±0.2
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
ℓ1ℓ1ℓ2 ℓ2
W
Lℓ1ℓ2 ℓ2
L
W
CWT-2250CWT-2275CWT-22100CWT-22150CWT-2850CWT-2875CWT-28100CWT-28150CWT-3850CWT-3875CWT-38100CWT-38150CWT-4850CWT-4875CWT-48100CWT-48150
Part No.
Specify Part No. by required width and length.
(e.g.) Width is 38mm and length is 150mm.
CWT - 38150
Motion direction
L
T
W
235
Sele
ctio
n G
uide
Prod
uct
Info
rmat
ion
Plas
tic B
earin
gM
ulti-
laye
r Bea
ring
Met
allic
Bea
ring
Air
Bear
ings
Tech
nica
l In
form
atio
nSl
ide
Shift
erCo
rpor
ate
Profi
le
184-271_金属系ヘ�アリンク�.indd 235 19/10/17 19:45
ThicknessWidth
Part No.T ToleranceW W1 W2
Length
LTolerance Tolerance Tolerance ℓ2Toleranceℓ1
Mounting hole intervalsNo.
of holes
5555555
75100125150100125150
75757575100100100
CWT-7575CWT-75100CWT-75125CWT-75150CWT-100100CWT-100125CWT-100150
45709560709560
15151515151515
45454545707070
15151515151515
4446446
±0.015
±0.015
±0.015
±0.015
±0.015
±0.015
±0.015
±0.2
±0.2
±0.2
±0.2
±0.2
±0.2
±0.2
±0.2
±0.2
±0.2
±0.2
±0.2
±0.2
±0.2
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
ℓ1ℓ2 ℓ2
L
WW1
W2
W2
Chamfering
Lℓ1ℓ1ℓ2 ℓ2
WW1
W2
W2
Cross-section
Sintered layer (1mm or more)
Back metal
T
φ1890°
φ10 16.3
4.4
20
16
M8×20 P1.25
●Mounting bolts
Provide the mating part with C2 or larger
chamfering if it is tapped for mounting.
φ12 or more
2 or more
C2 or more
R1 allcircumferences
C1 allcircumferences
236
Selection Guide
ProductInform
ationPlastic Bearing
Multi-layer Bearing
Metallic Bearing
Air Bearings
Technical Inform
ationSlide Shifter
Corporate Profi le
184-271_金属系ヘ�アリンク�.indd 236 19/10/17 19:45
CWX Oiles 2000 Wear Plates 10mm Thickness
●Use the exclusive low-head bolt for mounting.
(LHS-M1020 is attached to CWX series)
ThicknessWidth
Part No.T ToleranceW ℓ1 ℓ2
Length
LTolerance Tolerance Tolerance
Mounting hole intervalsNo.
of holesChamfering
4-C1.5ℓ1ℓ2 ℓ2
L
WW1
W2
W2
4-C1.5ℓ1ℓ1ℓ2 ℓ2W
4-C1.5ℓ1ℓ2 ℓ2
L L
W
Part No.
Specify Part No. by required width and length.
(e.g.) Width is 75mm and length is 125mm.
CWX - 75125
Motion direction
L
T
W
1010101010101010101010101010101010101010
7510012515075100125150751001251502002507510015075100125
2828282838383838484848484848585858757575
4550751004550751004550751001001004550100255075
1525252515252525152525255025152525252525
22222222222223222222
±0.01
±0.01
±0.01
±0.01
±0.01
±0.01
±0.01
±0.01
±0.01
±0.01
±0.01
±0.01
±0.01
±0.01
±0.01
±0.01
±0.01
±0.01
±0.01
±0.01
±0.2
±0.2
±0.2
±0.2
±0.2
±0.2
±0.2
±0.2
±0.2
±0.2
±0.2
±0.2
±0.2
±0.2
±0.2
±0.2
±0.2
±0.2
±0.2
±0.2
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
CCCCBBBBBBBBBBBBBAAA
CWX-2875CWX-28100CWX-28125CWX-28150CWX-3875CWX-38100CWX-38125CWX-38150CWX-4875CWX-48100CWX-48125CWX-48150CWX-48200CWX-48250CWX-5875CWX-58100CWX-58150CWX-7575CWX-75100CWX-75125
237
Sele
ctio
n G
uide
Prod
uct
Info
rmat
ion
Plas
tic B
earin
gM
ulti-
laye
r Bea
ring
Met
allic
Bea
ring
Air
Bear
ings
Tech
nica
l In
form
atio
nSl
ide
Shift
erCo
rpor
ate
Profi
le
184-271_金属系ヘ�アリンク�.indd 237 19/10/17 19:45
Sintered layer (1mm or more)
Back metal
T
φ18
φ11 2.5
2
6
C1.5 all circumferences
R10 all circumferences
2
3.5
C1.5 all circumferences
R5 all circumferences
C1.5 all circumferences
R2 all circumferences
● LHS Exclusive Bolt for CWX〔Part No. : LHS-M1020〕
●Exclusive bolt LHS-M1020 is attached to CWX
plate.
●The Exclusive bolt has approximate breaking
toque of JIS standard M10 socket head cap screw.
※Bolt itself is on sale.
N・m{kgf・m}
M10×P.1.5
φ16.8
8 (9.4)
6.3 20
Recommended tightening torque
Breaking torque
67.3{6.86}118{12.0}
LHS-M1020Part No.
ThicknessWidth
Part No.T ToleranceW
101010101010101010101010101010101010
W1 W2 ℓ1 ℓ2
Length
L
150200250300100125150200250300125150200250300150200250
Tolerance Tolerance Tolerance Tolerance
75757575100100100100100100125125125125125150150150
CWX-75150CWX-75200CWX-75250CWX-75300CWX-100100CWX-100125CWX-100150CWX-100200CWX-100250CWX-100300CWX-125125CWX-125150CWX-125200CWX-125250CWX-125300CWX-150150CWX-150200CWX-150250
Mounting hole intervalsNo.
of holes
100150100100507510015020020075100150200200100150200
252525502525252525502525252550252525
5050505050507550505050100100100
2525252525252537.537.537.537.5252525
223344444444444444
±0.01
±0.01
±0.01
±0.01
±0.01
±0.01
±0.01
±0.01
±0.01
±0.01
±0.01
±0.01
±0.01
±0.01
±0.01
±0.01
±0.01
±0.01
±0.2
±0.2
±0.2
±0.2
±0.2
±0.2
±0.2
±0.2
±0.2
±0.2
±0.2
±0.2
±0.2
±0.2
±0.2
±0.2
±0.2
±0.2
±0.2
±0.2
±0.2
±0.2
±0.2
±0.2
±0.2
±0.2
±0.2
±0.2
±0.2
±0.2
±0.2
±0.2
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
Chamfering
AAAAAAAAAAAAAAAAAA
Cross-section
Chamfering
Type A
Type B
Type C
6.3
238
Selection Guide
ProductInform
ationPlastic Bearing
Multi-layer Bearing
Metallic Bearing
Air Bearings
Technical Inform
ationSlide Shifter
Corporate Profi le
184-271_金属系ヘ�アリンク�.indd 238 19/10/17 19:45
CWXT Oiles 2000 Wear Plates 10mm Thickness (2 hole type)
●Use the exclusive low-head bolt for mounting.
(LHS-M1020 is attached to CWXT series)
Specify Part No. by required width and length.
(e.g.) Width is 100mm and length is 200mm.
Motion direction
Part No.CWXT - 100200
Cross-section Chamfering
Type ASintered layer (1mm or more)
Back metal
T
φ18
φ11 2.5
2
6
C1.5 all circumferences
R10 all circumferences
N・m{kgf・m}M10×P.1.5
φ16.8
8 (9.4)
6.3 20Recommended tightening torque
Breaking torque
67.3{6.86}118{12.0}
LHS-M1020Part No.
Part No. TW1010101010101010101010101010
ℓ1 ℓ2L100125150200250300125150200250300150200250
100100100100100100125125125125125150150150
507510015020020075100150200200100150200
2525252525502525252550252525
22222222222222
±0.01
±0.01
±0.01
±0.01
±0.01
±0.01
±0.01
±0.01
±0.01
±0.01
±0.01
±0.01
±0.01
±0.01
±0.2
±0.2
±0.2
±0.2
±0.2
±0.2
±0.2
±0.2
±0.2
±0.2
±0.2
±0.2
±0.2
±0.2
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
AAAAAAAAAAAAAA
4-C1.5ℓ1ℓ2 ℓ2
L
W
6.3
CWXT-100100CWXT-100125CWXT-100150CWXT-100200CWXT-100250CWXT-100300CWXT-125125CWXT-125150CWXT-125200CWXT-125250CWXT-125300CWXT-150150CWXT-150200CWXT-150250
L
T
W
Width Length Thickness Mounting hole intervalsNo.
of holesChamfering
Tolerance Tolerance Tolerance Tolerance
● LHS Exclusive Bolt for CWXT〔Part No. : LHS-M1020〕
●Exclusive bolt LHS-M1020 is attached to CWXT
plate.
●The Exclusive bolt has approximate breaking
toque of JIS standard M10 socket head cap screw.
※Bolt itself is on sale.
239
Sele
ctio
n G
uide
Prod
uct
Info
rmat
ion
Plas
tic B
earin
gM
ulti-
laye
r Bea
ring
Met
allic
Bea
ring
Air
Bear
ings
Tech
nica
l In
form
atio
nSl
ide
Shift
erCo
rpor
ate
Profi
le
184-271_金属系ヘ�アリンク�.indd 239 19/10/17 19:45
CWA Oiles 2000 Wear Plates 10mm Thickness
●Use M6×20 hexagon socket head bolt for
mounting.
4-C1.5ℓ1ℓ2 ℓ2
L
W
R2 all circumferences
Sintered layer (1mm or more)
Back metal
T
φ11
φ6.7
3
C1.5 all circumferences
ThicknessWidth
Part No.T ToleramceW
10101010
ℓ1 ℓ2
Length
L
75100125150
±0.01
±0.01
±0.01
±0.01
±0.2
±0.2
±0.2
±0.2
Toleramce Toleramce Toleramce
-0.1
-0.1
-0.1
-0.1
-0.3
-0.3
-0.3
-0.3
-0.1
-0.1
-0.1
-0.1
-0.3
-0.3
-0.3
-0.3
18181818
CWA-1875NCWA-18100NCWA-18125NCWA-18150N
Mounting hole intervalsNo.
of holes
455075100
15252525
2222
Cross-section
6.3
Motion direction
Part No.
Specify Part No. by required width and length.
(e.g.) Width is 18mm and length is 100mm.
CWA - 18100 N
W
T L
240
Selection Guide
ProductInform
ationPlastic Bearing
Multi-layer Bearing
Metallic Bearing
Air Bearings
Technical Inform
ationSlide Shifter
Corporate Profi le
184-271_金属系ヘ�アリンク�.indd 240 19/10/17 19:45
CWP Oiles 2000 Wear Plates
4-C1ℓ1ℓ2 ℓ2
L
WW1
W2
W2
4-C1ℓ1ℓ1ℓ2 ℓ2
W
4-C1ℓ1ℓ2 ℓ2
L L
W
ThicknessWidth
T ToleranceW
202020202020202020202020202020
ℓ1 ℓ2
Length
L
75100150751001507510012515020025075100150
Tolerance Tolerance Tolerance
282828383838484848484848585858
Part No.
CWP-2875CWP-28100CWP-28150CWP-3875CWP-38100CWP-38150CWP-4875CWP-48100CWP-48125CWP-48150CWP-48200CWP-48250CWP-5875CWP-58100CWP-58150
Mounting hole intervals
45501004550100455075100100100
152525152525152525255025152525
4550100
222222222223222
Chamfering
±0.01
±0.01
±0.01
±0.01
±0.01
±0.01
±0.01
±0.01
±0.01
±0.01
±0.01
±0.01
±0.01
±0.01
±0.01
DDDCCCBBBBBBBBB
±0.2
±0.2
±0.2
±0.2
±0.2
±0.2
±0.2
±0.2
±0.2
±0.2
±0.2
±0.2
±0.2
±0.2
±0.2
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
Motion direction
Part No.
Specify Part No. by required width and length.
(e.g.) Width is 58mm and length is 150mm.
CWP - 58150
L
T
W
Type Qty
Attach bolts
M10 Hexagonsocket head
M10 Hexagonsocket head
M10 Hexagonsocket head
M10 Hexagonsocket head
M10 Hexagonsocket head
M10 Hexagonsocket head
M10 Hexagonsocket head
M10 Hexagonsocket head
M10 Hexagonsocket head
M10 Hexagonsocket head
M10 Hexagonsocket head
M10 Hexagonsocket head
M10 Hexagonsocket head
M10 Hexagonsocket head
M10 Hexagonsocket head
241
Sele
ctio
n G
uide
Prod
uct
Info
rmat
ion
Plas
tic B
earin
gM
ulti-
laye
r Bea
ring
Met
allic
Bea
ring
Air
Bear
ings
Tech
nica
l In
form
atio
nSl
ide
Shift
erCo
rpor
ate
Profi
le
184-271_金属系ヘ�アリンク�.indd 241 19/10/17 19:45
Sintered layer (1mm or more)
Back metal
T
φ17.5
φ11 8
Cross-section
Chamfering
2
6
Type A
2
3.5
Type B
2
3.5
Type C
2
Type D
ChamferingThicknessWidth
T
202020202020202020202020202020202020202020
Length
L
75100125150200250300100125150200250300125150200250300150200250
TolerancePart No.
CWP-7575BCWP-75100BCWP-75125CWP-75150CWP-75200CWP-75250CWP-75300CWP-100100CWP-100125CWP-100150CWP-100200CWP-100250CWP-100300CWP-125125CWP-125150CWP-125200CWP-125250CWP-125300CWP-150150CWP-150200CWP-150250
Mounting hole intervals
Tolerance
±0.01
±0.01
±0.01
±0.01
±0.01
±0.01
±0.01
±0.01
±0.01
±0.01
±0.01
±0.01
±0.01
±0.01
±0.01
±0.01
±0.01
±0.01
±0.01
±0.01
±0.01
Tolerance
±0.2
±0.2
±0.2
±0.2
±0.2
±0.2
±0.2
±0.2
±0.2
±0.2
±0.2
±0.2
±0.2
±0.2
222223344444444444444
AAAAAAAAAAAAAAAAAAAAA
ℓ2
252525252525502525252525502525252550252525
Tolerance
±0.2
±0.2
±0.2
±0.2
±0.2
±0.2
±0.2
±0.2
±0.2
±0.2
±0.2
±0.2
±0.2
±0.2
±0.2
±0.2
±0.2
±0.2
±0.2
±0.2
±0.2
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
Tolerance
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
W
75757575757575100100100100100100125125125125125150150150
W1
W2
25 252525252537.537.537.537.537.5252525
ℓ1
255075100150100100507510015020020075100150200200100150200
5050505050505050505050100100100
6.3
R10 allcircumferences
R5 allcircumferences
C3 allcircumferences
C3 allcircumferences
R5 allcircumferences
R2.5 allcircumferences
C1 allcircumferences
C1 allcircumferences
Type Qty
Attach bolts
M10 Hexagonsocket head
M10 Hexagonsocket head
M10 Hexagonsocket head
M10 Hexagonsocket head
M10 Hexagonsocket head
M10 Hexagonsocket head
M10 Hexagonsocket head
M10 Hexagonsocket head
M10 Hexagonsocket head
M10 Hexagonsocket head
M10 Hexagonsocket head
M10 Hexagonsocket head
M10 Hexagonsocket head
M10 Hexagonsocket head
M10 Hexagonsocket head
M10 Hexagonsocket head
M10 Hexagonsocket head
M10 Hexagonsocket head
M10 Hexagonsocket head
M10 Hexagonsocket head
M10 Hexagonsocket head
242
Selection Guide
ProductInform
ationPlastic Bearing
Multi-layer Bearing
Metallic Bearing
Air Bearings
Technical Inform
ationSlide Shifter
Corporate Profi le
184-271_金属系ヘ�アリンク�.indd 242 19/10/17 19:45
CWPT Oiles 2000 Wear Plates 20mm Thickness (2 hole type)
●CTP series were renamed CWPT series.
Specify Part No. by required width and length.
(e.g.) Width is 125mm and length is 150mm.
Motion direction
Part No.CWPT - 125150
Cross-section Chamfering
Type A
4-C1ℓ1ℓ2 ℓ2
L
W
Sintered layer (1mm or more)
Back metal
T
φ17.5
φ11 86.3
2
6
C3 all circumferences
R10 all circumferences
TW2020202020202020202020202020
ℓ1 ℓ2L100125150200250300125150200250300150200250
100100100100100100125125125125125150150150
Part No.
CWPT-100100CWPT-100125CWPT-100150CWPT-100200CWPT-100250CWPT-100300CWPT-125125CWPT-125150CWPT-125200CWPT-125250CWPT-125300CWPT-150150CWPT-150200CWPT-150250
507510015020020075100150200200100150200
2525252525502525252550252525
22222222222222
±0.01
±0.01
±0.01
±0.01
±0.01
±0.01
±0.01
±0.01
±0.01
±0.01
±0.01
±0.01
±0.01
±0.01
AAAAAAAAAAAAAA
±0.2
±0.2
±0.2
±0.2
±0.2
±0.2
±0.2
±0.2
±0.2
±0.2
±0.2
±0.2
±0.2
±0.2
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
L
T
W
Width Length Thickness Mounting hole intervalsChamfering
Tolerance Tolerance Tolerance Tolerance Type Qty
Attach bolts
M10 Hexagonsocket head
M10 Hexagonsocket head
M10 Hexagonsocket head
M10 Hexagonsocket head
M10 Hexagonsocket head
M10 Hexagonsocket head
M10 Hexagonsocket head
M10 Hexagonsocket head
M10 Hexagonsocket head
M10 Hexagonsocket head
M10 Hexagonsocket head
M10 Hexagonsocket head
M10 Hexagonsocket head
M10 Hexagonsocket head
243
Sele
ctio
n G
uide
Prod
uct
Info
rmat
ion
Plas
tic B
earin
gM
ulti-
laye
r Bea
ring
Met
allic
Bea
ring
Air
Bear
ings
Tech
nica
l In
form
atio
nSl
ide
Shift
erCo
rpor
ate
Profi
le
184-271_金属系ヘ�アリンク�.indd 243 19/10/17 19:45
CWI Oiles 2000 Plates for Additional Machining
●For additional machining, cutting or drilling to
your required dimension.
●Machine the back metal side to adjust the
thickness.
●Oil impregnation is necessary by referring to
the oil impregnation method, page 250 when
you machined the plate.
Sintered layer (1mm or more)
Back metal
L
T
W
Motion direction
Part No.
Specify Part No. by required width, length, and thickness.
(e.g.) With is 100mm, length is 200mm,
and thickness is 15mm.CWI - 10020015
6.3
Width
Part No.W
Length
L
480480200480480200480200480200250420150250250
505010040150100150100150120150150100150150
CWI-504806CWI-504808CWI-10020010CWI-4048010CWI-15048010CWI-10020012CWI-15048012CWI-10020015CWI-15048015CWI-12020020CWI-15025020CWI-15042020CWI-10015025CWI-15025025CWI-15025030
Thickness
T Tolerance
6810101012121515202020252530
±0.02
±0.02
±0.02
±0.02
±0.02
±0.02
±0.02
±0.02
±0.02
±0.02
±0.02
±0.02
±0.02
±0.02
±0.02
●Following table indicates mating dimensions used for application of general screws and bolts.
※The values in parentheses are applicable when exclusive low-head bolt LHS-M1020 are used.※The sink dimension (A) does not conform to JIS Standard, since these are sliding materials.
TypePlate thickness T
MAdd1KMAdd1BMAdd1B
Flat head machine screws
Flat fillister head screw
Hexagon socket cap screw
φd1
TKA
φd
φd1
TKB
Aφd
φd1
TKB
A
φd
M8
M5
-----
1 10 19.3
0.75.510 2
6 8
M10
M6
M5
1 12 22 5.0
1.66.612 2.5
1 5.59.52
10
M10
M8
M6(10 )1.5( 1.2)6.7(11 )11 (18 )2.5( 2.5)
M8(10 )1( 2.7)9(11 )15(18 )3( 3 )
1.512 23 5.0
1.89 16 3
15
----------M101.511 17.53.5
12
----------
20
----------M121.514 20 6.5
25
----------M161.518 26 7.5
30
----------M201.522 32 8.5
4.65
244
Selection Guide
ProductInform
ationPlastic Bearing
Multi-layer Bearing
Metallic Bearing
Air Bearings
Technical Inform
ationSlide Shifter
Corporate Profi le
184-271_金属系ヘ�アリンク�.indd 244 19/10/17 19:45
Oiles Shoe Units Unit bearings
Feature ●Usable as not only movable platens but also various types of shims and spacers.●The sliding material is made of Oiles 2000 featuring superior wear resistance.●The slide seals are attached to the slide plates, eliminating troublesome
adjustment of the slide seals after height adjustment.●The height is adjustable in ±0.25 to ±0.7 mm range.
Part No. Height-adjustablerange (mm)
Sliding surfacelength (mm)
Sliding area(cm2)
Load (Note)(N/2pc){kgf/2pc}
Assumed mold clamping force(kN){ton}
■ Usage in Injection molding machine.
PAC30-90PAC40-100PAC50-150PAC60-160PAC75-180PAC100-250PAC125-250PAC150-300
±0.25±0.35±0.35±0.35±0.35±0.7±0.7±0.7
5555100110130250250300
16.522 50 66 97.5250 312.5 450
6,470{ 660} 8,630{ 880} 19,600{ 2,000} 25,900{ 2,640} 38,200{ 3,900} 98,100{10,000}122,600{12,500}176,500{18,000}
830 or less{ 85 or less} 830~ 980{ 85~ 100} 980~ 2,450{100~ 250}2,450~ 3,920{250~ 400}3,920~ 5,880{400~ 600}5,880~ 7,850{600~ 800}7,840~12,750{800~1,300} 15,690 or less{1,600 or less}
(Note)Load is based on the design surface pressure of 1.96N/mm2{20kgf/cm2}.
Oiles Shoe UnitPAC
The Oiles Shoe Units are unit bearings developed as shoe units of movable platens for injection molding machines.
245
Sele
ctio
n G
uide
Prod
uct
Info
rmat
ion
Plas
tic B
earin
gM
ulti-
laye
r Bea
ring
Met
allic
Bea
ring
Air
Bear
ings
Tech
nica
l In
form
atio
nSl
ide
Shift
erCo
rpor
ate
Profi
le
184-271_金属系ヘ�アリンク�.indd 245 19/10/17 19:45
PAC Oiles Shoe Units
Part No.
Specify Part No. by required size.
(e.g.) Width is 50mm.
3040506075100125150
(M6)(M6)(M8)(M10)(M10)(M12)(M12)(M16)
6.58152025
1313161717253040
2535657085120120120
3015202025202040
20.523.528 32 33 43 4350
7.518202020202020
4.55566101010
M 8×25M10×30M12×35M12×35M12×35M16×40M16×40M20×40
M 6×35M 6×40M 8×50M 8×50M 8×50M10×70M10×70M12×70
3040455050606070
8090140150170250250300
PAC30-90PAC40-100PAC50-150PAC60-160PAC75-180PAC100-250PAC125-250PAC150-300
5555100110130200200250
15253035456080100
PAC 50 - 150
Table
Slide plate
Slide seal*
Adjustable push bolt
Adjustable pull bolt
Spring washers
Set screw for seal*
Grease nipple
Spring pin
SS4002000
NBR+SPCCSCM435SCM435SCM435SCM435
S15C(C-PT1/8)S60CM
①②③④⑤⑥⑦⑧⑨
MaterialPart name
W=30、40、50、60、75 W=100、125、150
ℓ2 ℓ1 D
W1
W2
L W
d
H h1
W3
ℓ3
W
h2
④⑤⑥①②⑨⑧
ℓ2 ℓ1 D
W1
L
H
L
ℓ3 30
h1
W
W3 W3
h2
①②⑨ ⑧
④ ⑤⑥
Width Length Adjustable boltsHeight
Part No. D W1 W2 W3 ℓ1 ℓ2 ℓ3 h1 h2 d ④ ⑤W L H
d
③ ⑦
③ ⑦
※PAC30-90 does not have a slide seal and set screw for seal.
246
Selection Guide
ProductInform
ationPlastic Bearing
Multi-layer Bearing
Metallic Bearing
Air Bearings
Technical Inform
ationSlide Shifter
Corporate Profi le
184-271_金属系ヘ�アリンク�.indd 246 19/10/17 19:45
Oiles 2000S Sintered oil-impregnated bearings with dispersed solid lubricant
Feature●Ser viceable without the need for lubrication. Demonstrates higher
performance when greased.●Distributed solid lubricant allows motions in any direction.●Features low coefficient of friction and quite superior wear resistance.●Lower prices than bearings with copper alloy bases.
Density
Radial crushing strength
Hardness
Oil impregnation rate
Co-efficient of thermal expansion
JIS Z 2507
JIS K 7202-2
5.7
350{36}
90
16
1.2
Mechanical proper ties
Ser vice rangeLubrication condition
Service temperature range ℃Allowable max. pressure P N/mm2{kgf/cm2}
Allowable max. velocity V m/s{m/min}
Allowable max. PV value N/mm2・m/s{kgf/cm2・m/min}
Dry (initial greasing recommended)
-40~+120
29(49){296(500)}
1.00{60}
1.63{1,000}
※The value shown above are for sintered layer.
g/cm3
N/mm2{kgf/mm2}
HRM
vol%
×10-5 ℃-1
The values in parentheses are stat ic bearing pressures, which are the bearing pressures in appl ica t ions wi th no mot ion or very smal l mot ion (≦0.0017m/s[0.1m/min]).
247
Sele
ctio
n G
uide
Prod
uct
Info
rmat
ion
Plas
tic B
earin
gM
ulti-
laye
r Bea
ring
Met
allic
Bea
ring
Air
Bear
ings
Tech
nica
l In
form
atio
nSl
ide
Shift
erCo
rpor
ate
Profi
le
184-271_金属系ヘ�アリンク�.indd 247 19/10/17 19:45
Test data
WW
W
W
Journal oscillation test<Testing conditions>Bearing dimension : φ60×φ75×R50Mating material : S45C quenched by high frequency induction hardeningPressure : 24.5N/mm2{250.0kgf/cm2}Velocity : 0.033m/s{2.0m/min}Oscillating cycle : 21.2cpmOscillating angle : ±45°Test time : 100hrs.(durable cycle frequency : 127,200 cycles)Ambience : in the atmosphere, room temp.Lubrication : initial greasing
Journal rotation test<Testing conditions>Bearing dimension : φ40×φ50×R30Mating material : S45C quenched by high frequency induction hardeningTest time : 100hrs.Ambience : in the atmosphere, room temp.Pressure :VelocityLubrication
Receprocation test<Testing conditions>Mating material : SCM440 hard-chrome platingPressure : 1.18N/mm2{12.0kgf/cm2}Velocity : 1m/s{60m/min}Test time : 27.8hrs.Lubrication : Initial greasing
9.8N/mm2{100.0kgf/cm2}0.167m/s{10.0m/min}Initial greasing19.6N/mm2{200.0kgf/cm2}0.083m/s{5.0m/min}Dry
0.5
0.4
0.3
0.2
0.1
0100 20 30 40 908050 60 10070
Coefficient of friction〔μ〕
Test time〔hrs.〕
Wear amount bearing : 0.024mm
0.4
0.3
0.2
0.1
050 10 15 20 25 30
Coefficient of friction〔μ〕
Test time〔hrs.〕
Wear amount〔μm〕0 5 10 15 302520
0.5
0.4
0.3
0.2
0.1
0100 20 30 40 908050 60 10070
Coefficient of friction〔μ〕
Test time〔hrs.〕
Wear amount bearing : 0.001mm0.007mm
248
Selection Guide
ProductInform
ationPlastic Bearing
Multi-layer Bearing
Metallic Bearing
Air Bearings
Technical Inform
ationSlide Shifter
Corporate Profi le
184-271_金属系ヘ�アリンク�.indd 248 19/10/17 19:45
Oiles Cermet M Sintered bearings with dispersed solid lubricant
Feature●Ser viceable without the need for lubrication. Demonstrates higher
performance when lubricated.●Demonstrates superior wear resistance in applications where oil film is seldom
produced such as reciprocating motions, oscillation, frequent starts and stops, etc.●Standard products and materials for machining are available in various sizes.
Relief angle
Rake angle
Nose radius (mm)
Speed (m/min)
Cut depth (mm)
Feed (mm/rev)
carbide tool(JIS)
2~5゜
10~20゜
0.40~0.80
100~120
0.20~0.30
0.03~0.10
Lathe turning
Cu
ttin
g t
ool
Con
dit
ion
I.D.
class 7 to 8
O.D.
class 6 to 7
Length
class 8 to 9
Machining accuracy (bushing)
Classes here are in JIS standard.
This product demonstrates satisfactory performance at the slide surface roughness of Rz6.3 to 12.5μm.
※The value shown above are for sintered layer.
Apply grease or oil impregnation after machining.
使用範囲潤滑条件
使用温度範囲 ℃許容最高荷重 P N/mm2{kgf/cm2}許容最高速度 V m/s{m/min}許容最高 PV値 N/mm2・m/s{kgf/cm2・m/min}
無潤滑
-40~+300
0.50{30}
1.65{1,010}
29(98){296(1,000)}
定期潤滑
-40~+150
1.00{60}
3.25{1,990}
Service rangeLubrication condition
Service temperature range ℃Allowable max. pressure P N/mm2{kgf/cm2}
Allowable max. velocity V m/s{m/min}
Allowable max. PV value N/mm2・m/s{kgf/cm2・m/min}
Dry
-40~+200
0.85{51}
1.65{1,010}
10{102}
periodic lubrication
-40~+150
1.65{99}
2.45{1,500}
Density
Radial crushing strength
Hardness
Oil impregnation rate
Co-efficient of linear expansion
JIS Z 2507
JIS K 7202-2
6.4
137{14}
73
3
1.9
Mechanical proper tiesg/cm3
N/mm2{kgf/mm2}
HRM
vol%
×10-5 ℃-1
249
Sele
ctio
n G
uide
Prod
uct
Info
rmat
ion
Plas
tic B
earin
gM
ulti-
laye
r Bea
ring
Met
allic
Bea
ring
Air
Bear
ings
Tech
nica
l In
form
atio
nSl
ide
Shift
erCo
rpor
ate
Profi
le
184-271_金属系ヘ�アリンク�.indd 249 19/10/17 19:45
Test data
Oil impregnation method
W
Journal rotation test<Testing conditions>Mating material : S45CPressure : 1.96N/mm2{20.0kgf/cm2}Velocity : 0.17m/s{10.0m/min}Test time : 100hrs.Finishing method
Test piece after sizingMachined test piece
0.5
0.4
0.3
0.2
0.1
0
Coefficient of friction〔μ〕
200 40 60 80 100
Test time〔hrs.〕
Oil impregnation is required for oil-containing OILES bearings such as Oiles Cermet M. If you purchase tube or bar stocks, please follow the procedure below to impregnate finished products with lubrication oil before installation. If these bearings are stored for a long time or if the bearings are washed, re-impregnate before installation.Immerse the products into an oil bath. Heat the bath up to 100 ℃ to 110 ℃. Keep the temperature for 30 to 60 minutes until no more air bubbles come up.Cut the heat source and let it cool down to the room temperature.Take products out of the bath to install. If oil impregnation by heating is not possible, leave the products in the oil bath for 24 hours or more.
Operation conditions
Low load / high speed
Mid load / mid velocity
High load / low velocity
i.e.
Spindle oil
Motor oil
Gear oil
Viscosity
8 to 17cst(30℃)
8 to 15cst(98.9℃)
100 to 1000cst(37℃)
Types of oil
Selectoin of lubrication oil
Lubrication oil of low viscosity
Lubrication oil with limited viscosity change by temp.
Lubrication oil with high viscosity
Lubrication Oiles bearingsThermometer
Steel mesh
Heat source
250
Selection Guide
ProductInform
ationPlastic Bearing
Multi-layer Bearing
Metallic Bearing
Air Bearings
Technical Inform
ationSlide Shifter
Corporate Profi le
184-271_金属系ヘ�アリンク�.indd 250 19/10/17 19:45
54B Oiles Cermet M Bushings
I.D. O.D.
φd Tolerance φD Tolerance 6543 30252015108 40
34568101214151618202530
6781012161820212224283540
040704030603 030605
040705050805061005
040706050806061006081206101606
050808061008081208101608121808
061010081210101610121810142010152110162210182410
081215101615121815142015152115162215182415202815
101620121820142020152120162220182420202820253520304020
152125162225182425
253525304025 304040
182430202830253530304030
+0.014
+0.020
+0.020
+0.020
+0.025
+0.025
+0.032
+0.032
+0.032
+0.032
+0.032
+0.040
+0.040
+0.040
+0.024
+0.032
+0.032
+0.032
+0.040
+0.040
+0.050
+0.050
+0.050
+0.050
+0.050
+0.061
+0.061
+0.061
+0.015
+0.019
+0.019
+0.019
+0.023
+0.023
+0.023
+0.028
+0.028
+0.028
+0.028
+0.028
+0.034
+0.034
+0.027
+0.034
+0.034
+0.034
+0.041
+0.041
+0.041
+0.049
+0.049
+0.049
+0.049
+0.049
+0.059
+0.059
+0.017
+0.023
+0.023
+0.023
+0.029
+0.029
+0.039
+0.036
+0.036
+0.036
+0.036
+0.047
+0.044
+0.044
+0.007
+0.011
+0.011
+0.011
+0.014
+0.014
+0.021
+0.018
+0.018
+0.018
+0.018
+0.026
+0.018
+0.018
※The I.D. tolerance after press fitting is for reference only.
Length L Tolerance-0.1-0.3
Motiondirection
Mating shaft Bushing
1.6( )
h7
Housing
H7
chamfer
6.3( )
L
φdφD
1
20°
C0.3
C0.3
C0.3
φdE7
φDr7
L
●Some chamfering dimensions may differ from
the shown dimension.
Part No.
Specify Part No. by required I.D., O.D., and Length.
(e.g.) I.D. is 12mm, O.D. is 18mm, and length is 10mm.
54B - 121810
I.D. toleranceafter press
fitting(reference)
The dimensional tolerances are the values measured at +25℃.
0.25 or less
C0.3 ~ C0.5
0.25 or less
251
Sele
ctio
n G
uide
Prod
uct
Info
rmat
ion
Plas
tic B
earin
gM
ulti-
laye
r Bea
ring
Met
allic
Bea
ring
Air
Bear
ings
Tech
nica
l In
form
atio
nSl
ide
Shift
erCo
rpor
ate
Profi
le
184-271_金属系ヘ�アリンク�.indd 251 19/10/17 19:45
54F Oiles Cermet M Flange Bushings
I.D. O.D. Flange Length
φd Tolerance φD Tolerance φF t Tolerance
34568101214151618202530
-0.2
-0.2
-0.2
-0.2
-0.2
-0.2
-0.2
-0.2
-0.2
-0.2
-0.2
-0.2
-0.2
-0.2
0
0
0
0
0
0
0
0
0
0
0
0
0
0
6781012161820212224283540
1.51.51.522223333444
910111416202224272830344248
4.5 5.5 6.5 8 10 12 14 17 18 19 20 25 25 30
34568101214151617212126
Tolerance
0
0
0
0
0
0
0
0
0
0
0
0
0
0
-0.4
-0.4
-0.4
-0.4
-0.4
-0.4
-0.4
-0.4
-0.4
-0.4
-0.4
-0.4
-0.4
-0.4
0
0
0
0
0
0
0
0
0
0
0
0
0
0
+0.014
+0.020
+0.020
+0.020
+0.025
+0.025
+0.032
+0.032
+0.032
+0.032
+0.032
+0.040
+0.040
+0.040
+0.024
+0.032
+0.032
+0.032
+0.040
+0.040
+0.050
+0.050
+0.050
+0.050
+0.050
+0.061
+0.061
+0.061
+0.027
+0.034
+0.034
+0.034
+0.041
+0.041
+0.041
+0.049
+0.049
+0.049
+0.049
+0.049
+0.059
+0.059
+0.015
+0.019
+0.019
+0.019
+0.023
+0.023
+0.023
+0.028
+0.028
+0.028
+0.028
+0.028
+0.034
+0.034
-0.2
-0.2
-0.2
-0.2
-0.2
-0.2
-0.2
-0.2
-0.2
-0.2
-0.2
-0.2
-0.2
-0.2
Part No.
54F-030354F-040454F-050554F-060654F-080854F-101054F-121254F-141454F-151554F-161654F-181754F-202154F-252154F-3026
L ℓTolerance
Motiondirection
Mating shaft Flange bushing
H7
L
1.6( )
h7 φF
φdφD
Housing
H7
chamfer
6.3( )
t
Lt
C0.3
C0.3
C0.5
C0.3 or R0.3
R0.3
φdE7
φDr7
φF
●Some chamfering dimensions may differ from
the shown dimension.
Part No.
Specify Part No. by required I.D. and Length.
(e.g.) I.D. is 12mm and length is 12mm.
54F - 1212
ℓ
※The I.D. tolerance after press fitting is for reference only.
+0.017
+0.023
+0.023
+0.023
+0.029
+0.029
+0.039
+0.036
+0.036
+0.036
+0.036
+0.047
+0.044
+0.044
+0.007
+0.011
+0.011
+0.011
+0.014
+0.014
+0.021
+0.018
+0.018
+0.018
+0.018
+0.026
+0.023
+0.023
I.D. tolerance
after press
fitting (reference)
1
20°
The dimensional tolerances are the values measured at +25℃.
0.25 or less
C0.3 ~ C0.5
Flange side
C0.3 ~ C0.5
R0.2 ~ R0.4
C0.5 ~ C0.7
0.25 or less
0.25 or less
0.25 or less
Straight side
252
Selection Guide
ProductInform
ationPlastic Bearing
Multi-layer Bearing
Metallic Bearing
Air Bearings
Technical Inform
ationSlide Shifter
Corporate Profi le
184-271_金属系ヘ�アリンク�.indd 252 19/10/17 19:45
54M Oiles Cermet M Bar Stock
Part No. φD L
913182126334160
1016212631414649
54M-091054M-131654M-182154M-212654M-263154M-334154M-414654M-6049
Diameter Length●Oil impregnation is necessary by referring to
the oil impregnation method, page 250 when
you machined the plate.
L
φD
Part No.
Specify Part No. by required diameter and length.
(e.g.) Diameter is 21mm and length is 26mm.
54M - 2126
Tolerance Tolerance
+0.6
+0.6
+0.6
+0.8
+0.8
+0.8
+0.8
+2.0
+0.2
-0.2
-0.2
0
0
0
0
+1.0
+3.0
+3.0
+3.0
+3.0
+3.0
+3.0
+3.0
+3.0
0
0
0
0
0
0
0
0
253
Sele
ctio
n G
uide
Prod
uct
Info
rmat
ion
Plas
tic B
earin
gM
ulti-
laye
r Bea
ring
Met
allic
Bea
ring
Air
Bear
ings
Tech
nica
l In
form
atio
nSl
ide
Shift
erCo
rpor
ate
Profi
le
184-271_金属系ヘ�アリンク�.indd 253 19/10/17 19:45
54S Oiles Cermet M Bushing Material
I.D. O.D. Length
Part No. φd φD L
91415242929
232631414149
54S-09233354S-14263154S-15313154S-24413354S-29413654S-294933
333131333633
●Oil impregnation is necessary by referring to
the oil impregnation method, page 250 when
you machined the plate.
φdφD
L
Part No.
Specify Part No. by required I.D., O.D., and Length.
(e.g.) I.D. is 12mm, O.D. is 18mm, and length is 10mm.
54S - 153131
Tolerance Tolerance Tolerance
+0.5
+0.5
+0.5
+0.5
+0.5
+0.5
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
+3.0
+3.0
+3.0
+3.0
+3.0
+3.0
0
0
0
0
0
0
+0.6
+0.8
+0.6
+0.8
+0.8
+0.6
-0.2
0
-0.2
0
0
-0.2
254
Selection Guide
ProductInform
ationPlastic Bearing
Multi-layer Bearing
Metallic Bearing
Air Bearings
Technical Inform
ationSlide Shifter
Corporate Profi le
184-271_金属系ヘ�アリンク�.indd 254 19/10/17 19:45
Oiles Cermet G Sintered bearings with dispersed solid lubricant
Feature ●Serviceable without the need for lubrication. ●Features superior heat resistance.●Demonstrates superior performance in hot and hard-to-lubricate positions.●Materials for machining are available.
Density
Radial crushing strength
Hardness
Co-efficient of linear expansion
JIS Z 2507
JIS K 7202-2
6.4
137{14}
43
2.0
Mechanical proper tiesg/cm3
N/mm2{kgf/mm2}
HRM
×10-5 ℃-1
Relief angle
Rake angle
Nose radius (mm)
Speed (m/min)
Cut depth (mm)
Feed (mm/rev)
carbide tool(JIS)
2~5゜
10~20゜
0.40~0.80
100~120
0.20~0.30
0.03~0.10
Lathe turning
Cu
ttin
g t
ool
Con
dit
ion
I.D.
class 7 to 8
O.D.
class 6 to 7
Length
class 8 to 9
Machining accuracy (bushing)
Classes here are in JIS standard.
This product demonstrates satisfactory performance at the slide surface roughness of Rz6.3 to 12.5μm.
※The value shown above are for sintered layer.
Ser vice rangeLubrication condition
Service temperature range ℃Allowable max. pressure P N/mm2{kgf/cm2}
Allowable max. velocity V m/s{m/min}
Allowable max. PV value N/mm2・m/s{kgf/cm2・m/min}
Dry
-40~+250
0.50{30}
0.86{490}
periodic lubrication
-40~+150
0.85{51}
1.65{1,010}
10{102}
●About the material for machiningAlthough it is not oil-bearing material, it can be used as-is without lubrication.By applying an oil-bearing process or grease after machining, the reduction of wear and extension of life can be achieved.
255
Sele
ctio
n G
uide
Prod
uct
Info
rmat
ion
Plas
tic B
earin
gM
ulti-
laye
r Bea
ring
Met
allic
Bea
ring
Air
Bear
ings
Tech
nica
l In
form
atio
nSl
ide
Shift
erCo
rpor
ate
Profi
le
184-271_金属系ヘ�アリンク�.indd 255 19/10/17 19:45
Test data
Oil impregnation method
W
Thrast test<Testing conditions>
Bearing dimension : φ16×φ28×R15
Mating material : 0.49N/mm2{5.0kgf/cm2}
Velocity : 0.033m/s{2.0m/min}
Ambience : 300℃
Test time : 100hrs.
Lubrication : dry
1.0
0.8
0.6
0.4
0.2
0
Wear amount〔mm〕
200 40 60 80 100
Test time〔hrs.〕
Oiles Cermet G
Conventional sinteredcopper bearing
When you oil-impregnate Cemet G, please follow the procedure below to impregnate finished products with lubrication oil before installation. If these bearings are stored for a long time or if the bearings are washed, re-impregnate before installation.Immerse the products into an oil bath. Heat the bath up to 100 ℃ to 110 ℃. Keep the temperature for 30 to 60 minutes until no more air bubbles come up.Cut the heat source and let it cool down to the room temperature.Take products out of the bath to install. If oil impregnation by heating is not possible, leave the products in the oil bath for 24 hours or more.
Operation conditions
Low load / high speed
Mid load / mid velocity
High load / low velocity
i.e.
Spindle oil
Motor oil
Gear oil
Viscosity
8 to 17cst(30℃)
8 to 15cst(98.9℃)
100 to 1000cst(37℃)
Types of oil
Selectoin of lubrication oil
Lubrication oil of low viscosity
Lubrication oil with limited viscosity change by temp.
Lubrication oil with high viscosity
Lubrication Oiles bearingsThermometer
Steel mesh
Heat source
256
Selection Guide
ProductInform
ationPlastic Bearing
Multi-layer Bearing
Metallic Bearing
Air Bearings
Technical Inform
ationSlide Shifter
Corporate Profi le
184-271_金属系ヘ�アリンク�.indd 256 19/10/17 19:45
55M Oiles Cermet G Bar Stock
Diameter Length
φD L TolerancePart No.
55M-1155M-1555M-1855M-2355M-31
Tolerance
1115182331
2131213131
●Please refer to page 256 for the method for
oil-bearing treatment.
L
φD
0
0
0
0
0
+0.8
+0.8
+0.8
+0.8
+0.8
Part No.
Specify Part No. by required diameter.
(e.g.) Diameter is 18mm.
55M - 18
0
0
0
0
0
+3.0
+3.0
+3.0
+3.0
+3.0
257
Sele
ctio
n G
uide
Prod
uct
Info
rmat
ion
Plas
tic B
earin
gM
ulti-
laye
r Bea
ring
Met
allic
Bea
ring
Air
Bear
ings
Tech
nica
l In
form
atio
nSl
ide
Shift
erCo
rpor
ate
Profi
le
184-271_金属系ヘ�アリンク�.indd 257 19/10/17 19:45
55S Oiles Cermet G Bushing Material
Part No.
55S-19312655S-24363155S-28484655S-29414155S-34464155S-34515155S-39565155S-44565155S-49666155S-51736155S-54766155S-568161
I.D. O.D. Length
φd φD L
263146414151515161616161
192428293434394449515456
313648414651565666737681
●Please refer to page 256 for the method for
oil-bearing treatment.
φdφD
L
Tolerance Tolerance Tolerance
+0.3
+0.3
+1.2
+0.3
+0.3
+1.2
+1.2
+1.2
+1.2
+1.2
+1.2
+1.2
-0.5
-0.5
-1.2
-0.5
-0.5
-1.2
-0.5
-0.5
-1.2
-1.2
-1.2
-1.2
-0.5
-0.5
0
-0.5
-0.5
0
0
0
0
0
0
0
+0.3
+0.3
0
+0.3
+0.3
0
+0.3
+0.3
0
0
0
0
Part No.
Specify Part No. by required I.D., O.D., and Length.
(e.g.) I.D. is 44mm, O.D. is 56mm, and length is 51mm.
55S - 445651
+3.0
+3.0
+3.0
+4.0
+4.0
+4.0
+4.0
+4.0
+4.0
+4.0
+4.0
+4.0
0
0
0
0
0
0
0
0
0
0
0
0
258
Selection Guide
ProductInform
ationPlastic Bearing
Multi-layer Bearing
Metallic Bearing
Air Bearings
Technical Inform
ationSlide Shifter
Corporate Profi le
184-271_金属系ヘ�アリンク�.indd 258 19/10/17 19:45
Oiles 300 Oil-impregnated expanded cast iron bearings
Feature ●Reduces much less lubrication than copper alloy bearings.●Maintains oil film well and features superior wear resistance and seizure
resistance.●Places no restrictions on sliding surface shapes or motion forms.●Available in larger dimensions than oil-impregnated sintered bearings.●Standard products and materials for machining are available in various sizes.
Relief angle
Rake angle
Nose radius (mm)
Speed (m/min)
Cut depth (mm)
Feed (mm/rev)
carbide tool(JIS)
5~10゜
2~5゜
0.40~0.80
100~200
0.05~0.30
0.08~0.30
Lathe turning
Cu
ttin
g t
ool
Con
dit
ion
I.D.
class 7 to 8
O.D.
class 6 to 7
Length
class 8 to 9
Machining accuracy (bushing)
Classes here are in JIS standard.
This product demonstrates satisfactory performance at the slide surface roughness of Rz6.3 to 12.5μm.
※The values shown above are typical values, not the standard values.
Ser vice rangeLubrication condition
Service temperature range ℃Allowable max. pressure P N/mm2{kgf/cm2}
Allowable max. velocity V m/s{m/min}
Allowable max. PV value N/mm2・m/s{kgf/cm2・m/min}
periodic lubrication
-40~+100
1.00{60}
1.25{765}
10{102}
oil lubrication
-40~+150
3.35{201}
3.25{1,990}
Apply grease or oil impregnation after machining.
Density
Tensile strength
Compressive strength
Impact strength
Hardness
Modulus of longitudinal elasticity
Co-efficient of linear expansion
Thermal conductivity
JIS Z 2241
JIS Z 2242
JIS Z 2246
6.8
98{10}
294{30}
2{0.2}
20
58,000{6,000}
1.1
50.2{0.12}
Mechanical proper tiesg/cm3
N/mm2{kgf/mm2}
N/mm2{kgf/mm2}
J/cm2{kgfm/cm2}
HS
N/mm2{kgf/mm2}
×10-5 ℃-1
W/m℃{cal/sec℃cm}
259
Sele
ctio
n G
uide
Prod
uct
Info
rmat
ion
Plas
tic B
earin
gM
ulti-
laye
r Bea
ring
Met
allic
Bea
ring
Air
Bear
ings
Tech
nica
l In
form
atio
nSl
ide
Shift
erCo
rpor
ate
Profi
le
184-271_金属系ヘ�アリンク�.indd 259 19/10/17 19:45
Oil impregnation method
Test data
W
Oil impregnation is required for oil-containing OILES bearings such as Oiles 300. If you purchase tube or bar stocks, please follow the procedure below to impregnate finished products with lubrication oil before installation. If these bearings are stored for a long time or if the bearings are washed, re-impregnate before installation.Immerse the products into an oil bath. Heat the bath up to 100 ℃ to 110 ℃. Keep the temperature for 30 to 60 minutes until no more air bubbles come up.Cut the heat source and let it cool down to the room temperature.Take products out of the bath to install. If oil impregnation by heating is not possible, leave the products in the oil bath for 24 hours or more.
Operation conditions
Low load / high speed
Mid load / mid velocity
High load / low velocity
i.e.
Spindle oil
Motor oil
Gear oil
Viscosity
8 to 17cst(30℃)
8 to 15cst(98.9℃)
100 to 1000cst(37℃)
Types of oil
Selectoin of lubrication oil
Lubrication oil of low viscosity
Lubrication oil with limited viscosity change by temp.
Lubrication oil with high viscosity
Lubrication Oiles bearingsThermometer
Steel mesh
Heat source
Thrust rotation test(Comparison with various copper alloy)
<Testing conditions>Bearing dimension : φ25×φ48×t9Mating material : S55C(surface roughness Rz1.5μm)Pressure : initial contact pressure 0.99N/mm2{10.1kgf/cm2} 0.87N/mm2{8.9kgf/cm2} is inclementally loaded every 5 minutesFinal contact pressure : 20.2N/mm2{206.0kgf/cm2}Velocity : 0.162m/s{9.7m/min}Lubrication : in oil
Wear amount〔mm〕0 0.2 0.4 0.6 1.20 1.401.000.8
CAC403(BC3)
CAC502A(PBC2)
CAC603(LBC3)
Oiles 300
Coefficient of friction〔μ〕0 0.20.1
CAC403(BC3)
CAC502A(PBC2)
CAC603(LBC3)
Oiles 300 F
F
F
F
S
S
S
S
Load resistance test / Final contact pressure : 20.2N/mm2{206.0kgf/cm2}
F : Max. valueS : Initial value
260
Selection Guide
ProductInform
ationPlastic Bearing
Multi-layer Bearing
Metallic Bearing
Air Bearings
Technical Inform
ationSlide Shifter
Corporate Profi le
184-271_金属系ヘ�アリンク�.indd 260 19/10/17 19:45
30B Oiles 300 Bushings (Thin wall)
● Use Oiles 300 in lubrication oil or with
periodic lubrication.
Motiondirection
Mating shaft Bushing
φdφD
1.6( )
h7
Housing
H7
chamfer
6.3( )
Part No.
Specify Part No. by required I.D., O.D., and Length.
(e.g.) I.D. is 8mm, O.D. is 10mm, and length is 12mm.
30B - 081012 T
L
I.D. O.D.
φd Tolerance φD Tolerance 5
568101212141416161820
7810121416161818202224
050705T060805T
6
050706T060806T081006T
8
050708T060808T081008T101208T121408T121608T
10
060810T081010T101210T121410T121610T141610T141810T161810TT162010
12
081012T101212T121412T121612T141612T141812T
15
101215T121415T121615T141615T141815T161815T162015T
20
121420T121620T141620T141820T161820T162020T182220T202420T
30
182230T202430T
+0.058
+0.058
+0.062
+0.068
+0.081
+0.081
+0.081
+0.081
+0.081
+0.089
+0.089
+0.105
+0.034
+0.034
+0.034
+0.041
+0.041
+0.041
+0.041
+0.041
+0.041
+0.049
+0.049
+0.049
+0.030
+0.030
+0.034
+0.034
+0.047
+0.047
+0.047
+0.047
+0.047
+0.047
+0.047
+0.063
※The I.D. tolerance after press fitting is for reference only.
Length L Tolerance 0-0.2
I.D. toleranceafter press
fitting(reference)
C0.3
C0.3
C0.3
C0.3φdφD
L
+0.019
+0.019
+0.019
+0.023
+0.023
+0.023
+0.023
+0.023
+0.023
+0.028
+0.028
+0.028
+0.012
+0.012
+0.012
+0.012
+0.020
+0.020
+0.020
+0.020
+0.020
+0.020
+0.020
+0.030
+0.040
+0.040
+0.040
+0.046
+0.054
+0.054
+0.054
+0.054
+0.054
+0.062
+0.062
+0.072
The dimensional tolerances are the values measured at +25℃.
261
Sele
ctio
n G
uide
Prod
uct
Info
rmat
ion
Plas
tic B
earin
gM
ulti-
laye
r Bea
ring
Met
allic
Bea
ring
Air
Bear
ings
Tech
nica
l In
form
atio
nSl
ide
Shift
erCo
rpor
ate
Profi
le
184-271_金属系ヘ�アリンク�.indd 261 19/10/17 19:45
Oiles 300 Bushings Thin wall
Press-fitting
Housing chamferFor the housing chamfer, either a round chamfer or a
tapered chamfer is recommended. In case of a
C-surface chamfer, (more than C1.0) make sure there
is no burr. Smoother press-fitting is possible by
applying small amount of grease or lubricant.
Press-fit forcePress-fit smoothly with hydralic (pressure), pneumatic
pressure, or a vice. Avoid press-fit by use of impact
such as use of a hammer. It might induce damage of
the bushing, or change the size of the inner diameter
after press-fit.
Press-fitting jigGenerally, as shown in the figure 1, a mandrel is used
for the press-fitting. However use of a guide ring
facilitates easier press-fitting. Use of a guide ring
prevents damage of a bushing at the time of
press-fitting. The dimension of a guide ring should be
calculated from the table below.
Inner diameter of the guide ring should be the size so
that the bushing can be inserted by hands. Length of
the guide ring should be more than one-third of the
bushing, or if possible, it should be the same length as the bushing.
Dimension of bushing
I.D. D0
O.D. D1
Length L
Dimension of mandrel
d0=D0-(0.05 to 0.10)
d1=D1-(0.20 to 0.30)
R≧L
The dimension of mandrel should be calculatedfrom table below.
Load Load
Mandrel
Bushing Guide ring
Housing
Regular press-fitting Press-fitting with guide ring
L R
D0
d0
d1D1
The dimension of guide ring should be calculated from table below.
Bushing I.D.
Up to φ20
Guide ring O.D.
D1+(10 to 15)
Guide ring I.D.
D1+(0.1 to 0.3)
Figure 1
Figure 2
D1+(10~15)
D1+(0.1~0.3)
Mandrel
Bushing Guide ring
262
Selection Guide
ProductInform
ationPlastic Bearing
Multi-layer Bearing
Metallic Bearing
Air Bearings
Technical Inform
ationSlide Shifter
Corporate Profi le
184-271_金属系ヘ�アリンク�.indd 262 19/10/17 19:45
30B Oiles 300 Bushings
I.D. O.D.
φd Tolerance φD Tolerance 5
810121416181820202222222525282830303233353738403840424245
+0.034
+0.034
+0.041
+0.041
+0.041
+0.041
+0.041
+0.049
+0.049
+0.049
+0.049
+0.049
+0.049
+0.049
+0.049
+0.049
+0.049
+0.049
+0.059
+0.059
+0.059
+0.059
+0.059
+0.059
+0.059
+0.059
+0.059
+0.059
+0.059
+0.019
+0.019
+0.023
+0.023
+0.023
+0.023
+0.023
+0.028
+0.028
+0.028
+0.028
+0.028
+0.028
+0.028
+0.028
+0.028
+0.028
+0.028
+0.034
+0.034
+0.034
+0.034
+0.034
+0.034
+0.034
+0.034
+0.034
+0.034
+0.034
+0.030
+0.030
+0.034
+0.034
+0.045
+0.045
+0.045
+0.040
+0.040
+0.040
+0.040
+0.040
+0.040
+0.040
+0.040
+0.060
+0.060
+0.060
+0.054
+0.054
+0.054
+0.054
+0.054
+0.054
+0.054
+0.054
+0.054
+0.078
+0.078
6 8 10 12 15 16 20 25 30 35 40 50
5681010101212141415161618182020222225252528283030303232
※The I.D. tolerance after press fitting is for reference only.
Motiondirection
Mating shaft Bushing
φdφD
1.6( )
h7
Housing
H7
chamfer
6.3( )
Part No.
Specify Part No. by required I.D., O.D., and Length.
(e.g.) I.D. is 25mm, O.D. is 37mm, and length is 20mm.
30B - 253720
L
Length L Tolerance 0-0.2 I.D. tolerance
after press
fitting (reference)
+0.058
+0.058
+0.068
+0.068
+0.068
+0.068
+0.068
+0.068
+0.068
+0.068
+0.068
+0.068
+0.068
+0.068
+0.068
+0.088
+0.088
+0.088
+0.088
+0.088
+0.088
+0.088
+0.088
+0.088
+0.088
+0.088
+0.088
+0.112
+0.112
+0.012
+0.012
+0.012
+0.012
+0.023
+0.023
+0.018
+0.013
+0.013
+0.013
+0.013
+0.013
+0.013
+0.013
+0.013
+0.027
+0.027
+0.027
+0.021
+0.021
+0.021
+0.021
+0.021
+0.021
+0.021
+0.021
+0.021
+0.039
+0.039
+0.040
+0.040
+0.046
+0.046
+0.046
+0.046
+0.041
+0.041
+0.041
+0.041
+0.041
+0.041
+0.041
+0.041
+0.041
+0.055
+0.055
+0.055
+0.055
+0.055
+0.055
+0.055
+0.055
+0.055
+0.055
+0.055
+0.055
+0.073
+0.073
●Use Oiles 300 in lubrication oil or with
periodic lubrication.
050805061005
050806061006081206101406101606
050808061008081208101408101608101808121808
061010081210101410101610101810121810122010142010142210
081212101412101612101812121812122012142012142212
081215101415101615101815121815122015142015142215152215162215162515182515182815202815
121816
152216162216
202816
253316
101420101620101820121820122020142020142220152220162220162520182520182820202820203020223020223220253320253520253720
303820304020
121825122025142025142225152225162225162525182525182825202825203025223025223225253325253525
283825284025303825304025304225
162230162530182530182830202830203030223030223230253330253530253730
303830304030304230324230324530
162235
202835203035
253535
304035
202840203040223040223240253340253540253740283840284040303840304040304240324240324540
253350253550
303850304050
The dimensional tolerances are the values measured at +25℃.
263
Sele
ctio
n G
uide
Prod
uct
Info
rmat
ion
Plas
tic B
earin
gM
ulti-
laye
r Bea
ring
Met
allic
Bea
ring
Air
Bear
ings
Tech
nica
l In
form
atio
nSl
ide
Shift
erCo
rpor
ate
Profi
le
184-271_金属系ヘ�アリンク�.indd 263 19/10/17 19:45
a: Chamfering
φd ~22C0.3
100C1
~95C0.5 (mm)
I.D. O.D.
φd Tolerance φD Tolerance
45485055556060657075758080858590909595100100105110115115120120125
+0.078
+0.078
+0.078
+0.070
+0.070
+0.070
+0.070
+0.070
+0.102
+0.102
+0.102
+0.102
+0.102
+0.092
+0.092
+0.092
+0.092
+0.092
+0.092
+0.092
+0.136
+0.136
+0.136
+0.136
+0.136
+0.136
+0.136
+0.123
30
354530354830405030405530
40
354540354840405040405540455540456040506040506540
50
354550354850405050405550455550456050506050506550557050557550607550608050
60
506060506560557060557560607560608060658060658560708560709060759060759560809560
8010060
80
607580608080658080658580708580709080759080759580809580
8010080851008085105809011080901158095115809512080
1001208010012580
100
809510080100100851001008510510090110100901151009511510095120100
100120100100125100
120
100120120100125120
3535404045455050555560606565707075758080858590909595100100
Length L Length L0-0.2
0-0.4
1~2
20°
φdφD
L
a
Chamfering for the bush length of5 and 6mm are C0.3
※C0.5 for 30B-10012080
a
a
※The I.D. tolerance after press fitting is for reference only.
I.D. tolerance
after press
fitting (reference)
+0.073
+0.073
+0.073
+0.073
+0.073
+0.073
+0.073
+0.073
+0.098
+0.098
+0.098
+0.098
+0.098
+0.098
+0.098
+0.098
+0.098
+0.098
+0.098
+0.098
+0.134
+0.134
+0.134
+0.134
+0.134
+0.134
+0.134
+0.134
+0.112
+0.112
+0.112
+0.112
+0.112
+0.112
+0.112
+0.112
+0.144
+0.144
+0.144
+0.144
+0.144
+0.144
+0.144
+0.144
+0.144
+0.144
+0.144
+0.144
+0.188
+0.188
+0.188
+0.188
+0.188
+0.188
+0.188
+0.188
+0.059
+0.059
+0.059
+0.073
+0.073
+0.073
+0.073
+0.073
+0.073
+0.073
+0.073
+0.073
+0.073
+0.089
+0.089
+0.089
+0.089
+0.089
+0.089
+0.089
+0.089
+0.089
+0.089
+0.089
+0.089
+0.089
+0.089
+0.108
+0.039
+0.039
+0.039
+0.031
+0.031
+0.031
+0.031
+0.031
+0.056
+0.056
+0.056
+0.056
+0.056
+0.046
+0.046
+0.046
+0.046
+0.046
+0.046
+0.046
+0.082
+0.082
+0.082
+0.082
+0.082
+0.082
+0.082
+0.069
+0.034
+0.034
+0.034
+0.041
+0.041
+0.041
+0.041
+0.041
+0.041
+0.041
+0.041
+0.041
+0.041
+0.051
+0.051
+0.051
+0.051
+0.051
+0.051
+0.051
+0.051
+0.051
+0.051
+0.051
+0.051
+0.051
+0.051
+0.063
※
264
Selection Guide
ProductInform
ationPlastic Bearing
Multi-layer Bearing
Metallic Bearing
Air Bearings
Technical Inform
ationSlide Shifter
Corporate Profi le
184-271_金属系ヘ�アリンク�.indd 264 19/10/17 19:45
30F Oiles 300 Flange Bushings
a b c: Chamfering (mm)φd ~22
C0.5~60C1.5
~50C1
φd ~22R0.3
~60R1
~50R0.5
φd ~22C0.3
~60C0.5
I.D. O.D. Flange
φd ToleranceφD ToleranceφF t Tolerance 5
568101214151618202225283032354045505560
81012161820212225283035384042455055607075
1.52 23 33333.54 45 55555557.57.5
111420232527282933384045485052606570758590
+0.040
+0.040
+0.046
+0.046
+0.041
+0.041
+0.041
+0.041
+0.041
+0.055
+0.055
+0.055
+0.055
+0.055
+0.073
+0.073
+0.073
+0.073
+0.073
+0.098
+0.098
+0.058
+0.058
+0.068
+0.068
+0.068
+0.068
+0.068
+0.068
+0.068
+0.088
+0.088
+0.088
+0.088
+0.088
+0.112
+0.112
+0.112
+0.112
+0.112
+0.144
+0.144
8 10 12 15 20 25 30 40 50 60 80
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
-0.3
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Tolerance
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Part No.
Specify Part No. by required I.D. and length.
(e.g.) I.D. is 30mm and length is 40mm.
30F - 3040
+0.030
+0.030
+0.034
+0.045
+0.045
+0.040
+0.040
+0.040
+0.040
+0.060
+0.060
+0.054
+0.054
+0.054
+0.078
+0.078
+0.078
+0.070
+0.070
+0.102
+0.102
Length L Tolerance 0-0.3
Motiondirection
Mating shaft Flange bushing
L
6.3( )
chamfer
Housing
H7
t
1.6( )
h7 φF
φdφD
b
c
a
I.D. toleranceafter press
fitting(reference)
Chamfering for the bush length of 5 and 6mm are C0.3
φdφDφF
CC
Lt
a c
b1~2
20°
+0.019
+0.019
+0.023
+0.023
+0.023
+0.028
+0.028
+0.028
+0.028
+0.028
+0.028
+0.034
+0.034
+0.034
+0.034
+0.034
+0.034
+0.041
+0.041
+0.041
+0.041
+0.012
+0.012
+0.012
+0.023
+0.018
+0.013
+0.013
+0.013
+0.013
+0.027
+0.027
+0.021
+0.021
+0.021
+0.039
+0.039
+0.039
+0.031
+0.031
+0.056
+0.056
●Use Oiles 300 in lubrication oil or with
periodic lubrication.
0505 05080608 0610
08101010121014101510
081210121212141215121612
0815101512151415151516151815201522152515
102012201420152016201820202022202520
122514251525162518252025222525252825
1530163018302030223025302830303032303530
204022402540
30403240354040404540
4050455050505550
506055606060 6080
※The I.D. tolerance after press fitting is for reference only.
+0.034
+0.034
+0.041
+0.041
+0.041
+0.049
+0.049
+0.049
+0.049
+0.049
+0.049
+0.059
+0.059
+0.059
+0.059
+0.059
+0.059
+0.073
+0.073
+0.073
+0.073
The dimensional tolerances are the values measured at +25℃.
265
Sele
ctio
n G
uide
Prod
uct
Info
rmat
ion
Plas
tic B
earin
gM
ulti-
laye
r Bea
ring
Met
allic
Bea
ring
Air
Bear
ings
Tech
nica
l In
form
atio
nSl
ide
Shift
erCo
rpor
ate
Profi
le
184-271_金属系ヘ�アリンク�.indd 265 19/10/17 19:45
30W Oiles 300 Washers
Countersink type No hole type
●Use Oiles 300 in lubrication oil or with periodic
lubrication.
●Part no. with N at the end is no-hole type.
I.D. O.D. Thickness Mounting hole
φd Tolerance φD T Tolerance
10.212.213.214.216.218.220.225.230.235.240.245.250.3
304040405050505560708090100
3333335555778
+0.1
+0.1
+0.1
+0.1
+0.1
+0.1
+0.1
+0.1
+0.1
+0.1
+0.1
+0.1
+0.1
+0.2
+0.2
+0.2
+0.2
+0.2
+0.2
+0.2
+0.2
+0.2
+0.2
+0.2
+0.2
+0.3
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
-0.1
0
0
0
0
0
0
0
0
0
0
0
0
0
No.of holes
Countersinkscrew sizeP.C.D
no attach hole
no attach hole
no attach hole
no attach hole
no attach hole
Part No.
30W-1003N30W-1203N30W-1303N30W-1403N30W-1603N30W-180330W-200530W-250530W-300530W-350530W-400730W-450730W-5008
22222224
M3M5M5M5M5M6M6M6
3535404550607075
P.C.D
T
φdφD
C0.5~1
C0.5~1
φd
P.C.D
φD
T
C0.5~1
C0.5~1
C0.5
C0.5
C0.5
C0.5
φdφD
T
Part No.
Specify Part No. by required I.D. and thickness.
(e.g.) I.D. is 18.2mm and thickness is 3mm.
30W - 1803
266
Selection Guide
ProductInform
ationPlastic Bearing
Multi-layer Bearing
Metallic Bearing
Air Bearings
Technical Inform
ationSlide Shifter
Corporate Profi le
184-271_金属系ヘ�アリンク�.indd 266 19/10/17 19:45
30M Oiles 300 Bar Stock
Diameter Length
Part No. φD Tolerance ToleranceL
150200200200200200200200200200200200200200200200200200250250250
1521232527313335374043454750556065708090100
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
+1.0
+1.0
+1.0
+1.0
+1.0
+1.0
+1.0
+1.0
+1.0
+1.0
+1.0
+1.0
+1.0
+1.0
+1.0
+1.0
+1.0
+1.0
+1.0
+1.0
+1.0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
+3.0
+3.0
+3.0
+3.0
+3.0
+3.0
+3.0
+3.0
+3.0
+3.0
+3.0
+3.0
+3.0
+3.0
+3.0
+3.0
+3.0
+3.0
+3.0
+3.0
+3.0
●Length and diameter shown here are rough
finished dimensions.
●Oil impregnation is necessary by referring to
the oil impregnation method, page 260 when
you machined the plate.30M-1530M-2130M-2330M-2530M-2730M-3130M-3330M-3530M-3730M-4030M-4330M-4530M-4730M-5030M-5530M-6030M-6530M-7030M-8030M-9030M-100
L
φD
Part No.
Specify Part No. by required diameter.
(e.g.) Diameter is 40mm.
30M - 40
267
Sele
ctio
n G
uide
Prod
uct
Info
rmat
ion
Plas
tic B
earin
gM
ulti-
laye
r Bea
ring
Met
allic
Bea
ring
Air
Bear
ings
Tech
nica
l In
form
atio
nSl
ide
Shift
erCo
rpor
ate
Profi
le
184-271_金属系ヘ�アリンク�.indd 267 19/10/17 19:45
30S Oiles 300 Bushing Material
〈Thick wall〉
Part No.
919696101106111121126132142137147142152147157152162
7474797984899499103103108108113113118118123123
I.D. O.D. Length
φd φD L
I.D. O.D. Length
Part No. φd φD L
110120130140
200250250250
30S-6011030S-6512030S-7013030S-80140
60657080
Tolerance Tolerance Tolerance
I.D. O.D. Length
Part No. φd φD L
293134343739394444494954595964646969
100100150150150200200200200200200200200200200200200200
414346495351565661616671717681868691
-1.0
-1.0
-1.0
-1.0
-1.0
-1.0
-1.0
-1.0
-1.0
-1.0
-1.0
-1.0
-1.0
-1.0
-1.0
-1.0
-1.0
-1.0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Tolerance
-1.0
-1.0
-1.0
-1.0
-1.0
-1.0
-1.0
-1.0
-1.0
-1.0
-1.0
-1.0
-1.0
-1.0
-1.0
-1.0
-1.0
-1.0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Tolerance
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
+3.0
+3.0
+3.0
+3.0
+3.0
+3.0
+3.0
+3.0
+3.0
+3.0
+3.0
+3.0
+3.0
+3.0
+3.0
+3.0
+3.0
+3.0
Tolerance
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
+1.0
+1.0
+1.0
+1.0
+1.0
+1.0
+1.0
+1.0
+1.0
+1.0
+1.0
+1.0
+1.0
+1.0
+1.0
+1.0
+1.0
+1.0
Tolerance
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
+1.0
+1.0
+1.0
+1.0
+1.0
+1.0
+1.0
+1.0
+1.0
+1.0
+1.0
+1.0
+1.0
+1.0
+1.0
+1.0
+1.0
+1.0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
+3.0
+3.0
+3.0
+3.0
+3.0
+3.0
+3.0
+3.0
+3.0
+3.0
+3.0
+3.0
+3.0
+3.0
+3.0
+3.0
+3.0
+3.0
Tolerance Tolerance
30S-357030S-407530S-458030S-509030S-55100
3540455055
70758090100
I.D. O.D. Length
Part No. φd φD L
-1.0
-1.0
-1.0
-1.0
-1.0
0
0
0
0
0
Tolerance
0
0
0
0
0
0
0
0
0
0
+1.0
+1.0
+1.0
+1.0
+1.0
+3.0
+3.0
+3.0
+3.0
+3.0
Tolerance Tolerance
●Length and diameter shown here are rough finished dimensions.
●Oil impregnation is necessary by referring to the oil impregnation method, page 260 when you machined the plate.
●Length and diameter shown here are rough finished dimensions.
●Oil impregnation is necessary by referring to the oil impregnation method, page 260 when you machined the plate.
-1.0
-1.0
-1.0
-1.0
0
0
0
0
0
0
0
0
+1.0
+1.0
+1.0
+1.0
0
0
0
0
+3.0
+3.0
+3.0
+3.0
30S-749130S-749630S-799630S-7910130S-8410630S-8911130S-9412130S-9912630S-10313230S-10314230S-10813730S-10814730S-11314230S-11315230S-11814730S-11815730S-12315230S-123162
30S-294130S-314330S-344630S-344930S-375330S-395130S-395630S-445630S-446130S-496130S-496630S-547130S-597130S-597630S-648130S-648630S-698630S-6991
L
φdφD
Part No.
Specify Part No. by required I.D. and O.D.
(e.g.) I.D. is 69mm and O.D. is 86mm.
30S - 6986
200200200200200200200200250250250250250250250250250250
200200200200200
268
Selection Guide
ProductInform
ationPlastic Bearing
Multi-layer Bearing
Metallic Bearing
Air Bearings
Technical Inform
ationSlide Shifter
Corporate Profi le
184-271_金属系ヘ�アリンク�.indd 268 19/10/17 19:45
Oiles 600 Wear-resistant copper alloy bearings
Feature●Demonstrates wear resistance and seizure resistance in lubricated conditions.●Reduces the frequency of lubrication.●Demonstrates especially high running-in characteristics.●Materials for machining are available.
Relief angle
Rake angle
Nose radius (mm)
Speed (m/min)
Cut depth (mm)
Feed (mm/rev)
carbide tool(JIS)
5~10゜
2~5゜
0.40~0.80
100~200
0.05~0.30
0.08~0.30
Lathe turning
Cu
ttin
g t
ool
Con
dit
ion
I.D.
class 7 to 8
O.D.
class 6 to 7
Length
class 8 to 9
Machining accuracy (bushing)
Classes here are in JIS standard.
This product demonstrates satisfactory performance at the slide surface roughness of Rz6.3 to 12.5μm.※The values shown above are typical values, not the standard values.
Ser vice rangeLubrication condition
Service temperature range ℃Allowable max. pressure P N/mm2{kgf/cm2}
Allowable max. velocity V m/s{m/min}
Allowable max. PV value N/mm2・m/s{kgf/cm2・m/min}
periodic lubrication
1.65{99}
1.65{1,010}
-40~+150
15{153}
oil lubrication
5.00{300}
3.25{1,990}
Density
Tensile strength
Impact strength
Hardness
Modulus of longitudinal elasticity
Co-efficient of linear expansion
Thermal conductivity
JIS Z 2241
JIS Z 2242
JIS Z 2243
8.5
150{15}
10{1}
60
83,000{8,500}
1.8
71.1{0.17}
Mechanical proper tiesg/cm3
N/mm2{kgf/mm2}
J/cm2{kgfm/cm2}
HBW
N/mm2{kgf/mm2}
×10-5 ℃-1
W/m℃{cal/sec℃cm}
269
Sele
ctio
n G
uide
Prod
uct
Info
rmat
ion
Plas
tic B
earin
gM
ulti-
laye
r Bea
ring
Met
allic
Bea
ring
Air
Bear
ings
Tech
nica
l In
form
atio
nSl
ide
Shift
erCo
rpor
ate
Profi
le
184-271_金属系ヘ�アリンク�.indd 269 19/10/17 19:45
36M Oiles 600 Bar Stock
36S Oiles 600 Bushing Material
● Length and diameter shown here are rough
finished dimensions.
● Need to be oil-impregnated before use.
●Inner and outer diameter and Length shown
here are rough finished dimensions.
●Need to be oil-impregnated before use.
Part No.L
16212631364146515661
202202202202202202202202202202
36M-1636M-2136M-2636M-3136M-3636M-4136M-4636M-5136M-5636M-61
0
0
0
0
0
0
0
0
0
0
+1.0
+1.0
+1.0
+1.0
+1.0
+1.0
+1.0
+1.0
+1.0
+1.0
Tolerance
0
0
0
0
0
0
0
0
0
0
+0.5
+0.5
+0.5
+0.5
+0.5
+0.5
+0.5
+0.5
+0.5
+0.5
Tolerance
Diameter Length
φD
Part No.I.D. O.D. Length
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Tolerance
0
0
0
0
0
0
0
0
0
0
0
0
0
0
ToleranceTolerance
36S-193136S-193636S-243636S-294136S-294636S-344636S-345136S-395136S-396636S-445636S-496136S-497136S-598136S-6986
φd φD L
1919242929343439394449495969
3136364146465151665661718186
202202202202202202202202202202202202202202
+1.0
+1.0
+1.0
+1.0
+1.0
+1.0
+1.0
+1.0
+1.0
+1.0
+1.0
+1.0
+1.0
+1.0
+0.5
+0.5
+0.5
+0.5
+0.5
+0.5
+0.5
+0.5
+0.5
+0.5
+0.5
+0.5
+0.5
+0.5
-0.5
-0.5
-0.5
-0.5
-0.5
-0.5
-0.5
-0.5
-0.5
-0.5
-0.5
-0.5
-0.5
-0.5
0
0
0
0
0
0
0
0
0
0
0
0
0
0
L
φD
L
φdφD
Specify Part No. by required diameter.
(e.g.) Diameter is 36mm.
Part No.36M - 36
Specify Part No. by required I.D. and O.D.
(e.g.) I.D. is 34mm and O.D. is 51mm.
Part No.36S - 3451
270
Selection Guide
ProductInform
ationPlastic Bearing
Multi-layer Bearing
Metallic Bearing
Air Bearings
Technical Inform
ationSlide Shifter
Corporate Profi le
184-271_金属系ヘ�アリンク�.indd 270 19/10/17 19:45