View
3
Download
1
Category
Preview:
DESCRIPTION
Ejemplo Circuito paralelo
Citation preview
1.
Requ=1
1R1
+1R2
+1R3
Requ=1
11500Ω
+1
1800Ω+
12700Ω
=627.91Ω
I=VI
I= 12V627.91Ω
=0.02 A≈20mA
IR x=I∗ReqRx
IR1=0.02A∗627.91Ω1500
=0.008 A ≈8mA
IR2=0.02A∗627.91Ω1800
=0.007 A ≈7mA
IR3=0.02A∗627.91Ω2700
=0.005 A ≈5mA
________________
0.02A ≈20mAPor ser un circuito en paralelo el voltaje q pasa por R1, R2, R3 es el mismo. 12V
Potencia
P= V x I
P= 12V x 0.02= 0.240A ≈ 240 mA
PR1=12v∗0.008 A=0.096W ≈ 96mW
PR2=12v∗0.007 A=0.084W ≈84mW
PR3=12v∗0.005 A=0.060W ≈60mW________________
0.240W ≈ 240 mW
2.
Requ=1
1R1
+1R2
+1R3
+1R4
Requ=1
11500Ω
+1
1800Ω+
12700Ω
+1
150Ω
=121.076Ω
I=VI
I= 12V121.076Ω
=0.099 A ≈99mA
IR x=I∗ReqRx
IR1=0.02A∗121.076Ω
1500=0.008 A≈8mA
IR2=0.02A∗121.076Ω
1800=0.007≈7mA
IR3=0.02A∗121.076Ω
2700=0.004≈ 4mA
IR 4=0.02A∗121.076Ω
150=0.080≈80mA
I T=0.008 A+0.007 A+0.004 A+0.080 A=0.099 A≈99mA
Por ser un circuito en paralelo el voltaje q pasa por R1, R2, R3, R4 es el mismo. 12V
Potencia
P= V x I
P= 12V x 0.099A= 1.19W
PR1=12v∗0.008 A=0.10W
PR2=12v∗0.007 A=0.08W
PR3=12v∗0.004 A=0.05W
PR4=12v∗0.080 A=0.96W______1.19W
3.
Requ=1
1R1
+1R2
+1R3
+1R4
+1R5
Requ=1
11500Ω
+1
1800Ω+
12700Ω
+1
150Ω+1180
=72.386Ω
4.
I=VI
I= 12V72.386Ω
=0.166 A≈166mA
IR x=I∗ReqRx
IR1=0.166A∗72.386Ω1500
=0.008 A≈8mA
IR2=0.166A∗72.386Ω1800
=0.007 ≈7mA
IR3=0.166A∗72.386Ω2700
=0.004≈4mA
IR 4=0.166A∗72.386Ω
150=0.080≈80mA
IR5=0.166A∗72.386Ω
180=0.067≈67mA
______________ 0.166A ≈166mA
Por ser un circuito en paralelo el voltaje q pasa por R1, R2, R3, R4, R5 es el mismo. 12V
Potencia
P= V x I
P= 12V x 0.166A= 1.99W
PR1=12v∗0.008 A=0.10W
PR2=12v∗0.007 A=0.08W
PR3=12v∗0.004 A=0.05W
PR4=12v∗0.080 A=0.96W
PR5=12v∗0.067 A=0.80W_______1.99W
4.
Circuitos Requivalentes Intensidad Potencia1 627.91Ω 0.02A≈20mA 0.240A ≈ 240 mA
2 121.076Ω 0.099A≈99mA 1.19W
3 72.386Ω 0.166A≈166mA 1.99W
5. a. En un circuito en paralelo al aumentar el numero de resistencias su corriente aumenta.
b.
Las corrientes en las en las resistencias se mantuvieron igules al pasar de un circuito a otro.
c.
En cada resistencia cae la misma potencia, pero al aumentar el numero de resistencias la fuente entrega más potencia
Tercera actividad
Siendo X2= 26WX3= 60WX4= 100W
6. Un circuito en paralelo falla cuando se abre una fraccion del circuito, trayendo como consecuencia el no funcionamiento desde el lugar donde se abrio hacia atrás como se muestra en la siguiente figura.
7. Puede correguirse esa falla colocando un puente en ese segmento de circuito abierto
__
Requ=R1 x R2R1+R2
Requ=300Ωx 900Ω300Ω+900Ω
¿225Ω
Requ=100k Ω x 90k Ω100k Ω+90k Ω
=47368.4Ω≈ 47kΩ
Requ=0.05Ωx 0.08Ω0.05Ω+0.08Ω
=0.0308Ω
Requ=3000Ωx1200Ω3000Ω+1200Ω
=857.14Ω
Requ=10000Ωx 9000Ω10000Ω+9000Ω
=4736.84Ω≈ 4.73684kΩ
Requ=3000Ωx1200Ω3000Ω+1200Ω
=857.14Ω
Requ=1200000Ωx1500000Ω1200000Ω+1500000Ω
=666666.67Ω
Requ=0.03Ωx 0.06Ω0.03Ω+0.06Ω
=0.02Ω
Re=300Ω x500Ω300Ω+500Ω
=187.5Ω
Requ=187.5Ωx 800Ω187.5Ω+800Ω
=151.90Ω
Re=0.05Ω x0.16Ω0.05Ω+0.16Ω
=0.038Ω
Requ=0.038Ωx 0.21Ω0.038Ω+0.21Ω
=0.032Ω
Re=30000Ω x50000Ω30000Ω+50000Ω
=18750Ω≈18.75kΩ
Requ=80 kΩx 18750Ω80kΩ+18750Ω
=15189.87Ω≈15.18987 kΩ
Re=3MΩx 5MΩ3MΩ+5MΩ
=1.875MΩ
Req=1.875MΩ x7.5MΩ1.875MΩ+7.5MΩ
=1.452MΩ
Re=2000kΩ x5MΩ2000 kΩ+5MΩ
=1428571.4 MΩ
Re q=1428571.4 x 8000k Ω1428571.4+8000k Ω
=121212119MΩ
Re=0.02Ωx 0.05Ω0.02Ω+0.05Ω
=0.014Ω
Req=0.014Ω x0.04Ω0.014Ω+0.04Ω
=0.010Ω
Recommended