자동차센서 · 2014. 12. 29. · The gauge is attached to the object by a suitable adhesive,...

E-mail: hogijung@hanyang.ac.krhttp://web.yonsei.ac.kr/hgjung

자동차 센서

내용

• 센싱의 원리

• 자동차용 센서

• MEMS 기술

• 센서 네트워크

Sensor Basics: Potentiometer

The resistance of a given sample will increase with the length, but decrease with greater cross-sectional area.

ℓ’

접촉점의 위치 저항의 변화

http://en.wikipedia.org/wiki/Resistivity

Sensor Basics: Potentiometer

http://en.wikipedia.org/wiki/Potentiometer

If RL is large compared to the other resistances (like the input to an operational amplifier), the output voltage can be approximated by the simpler equation:

계측방법

Sensor Basics: Strain Gauge

Strain is the amount of deformation of a body due to an applied force. More specifically, strain (e) is defined as the fractional change in length, as shown in Figure 1.

Figure 1. Definition of Strain

http://zone.ni.com/devzone/cda/tut/p/id/3642

The gauge is attached to the object by a suitable adhesive, such as cyanoacrylate. As the object is deformed, the foil is deformed, causing its electrical resistance to change. This resistance change, usually measured using a Wheatstone bridge, is related to the strain by the quantity known as the gauge factor.

A typical strain gauge arranges a long, thin conductive strip in a zig-zag pattern of parallel lines such that a small amount of stress in the direction of the orientation of the parallel lines results in a multiplicatively larger strain over the effective length of the conductor—and hence a multiplicatively larger change in resistance—than would be observed with a single straight-line conductive wire.

http://en.wikipedia.org/wiki/Strain_gage

Typical foil strain gauge. The gauge is far more sensitive to strain in the vertical direction than in the horizontal direction.

http://en.wikipedia.org/wiki/Strain_gage

Visualization of the working concept behind the strain gauge on a beam under exaggerated bending.

Sensor Basics: Wheatstone Bridge

http://en.wikipedia.org/wiki/Wheatstone_bridge

It is used to measure an unknown electrical resistance by balancing two legs of a bridge circuit, one leg of which includes the unknown component.

In the figure, Rx is the unknown resistance to be measured; R1, R2 and R3 are resistors of known resistance and the resistance of R2 is adjustable.

If the ratio of the two resistances in the known leg (R2 / R1) is equal to the ratio of the two in the unknown leg (Rx / R3), then the voltage between the two midpoints (B and D) will be zero and no current will flow through the galvanometer Vg.

R2 / R1 = Rx / R3

If R1, R2, and R3 are known, but R2 is not adjustable, the voltage difference across or current flow through the meter can be used to calculate the value of Rx,

Sensor Basics: Piezoresistive effect

The piezoresistive effect describes the changing resistivity of a semiconductor due to applied mechanical stress.

In semiconductors, changes in inter-atomic spacing resulting from strain affects the bandgaps making it easier (or harder depending on the material and strain) for electrons to be raised into the conduction band. This results in a change in resistivity of the semiconductor.

http://en.wikipedia.org/wiki/Piezoresistive_effect

Sensor Basics: Piezoresistive effect

Piezoresistivity is defined by

Piezoresistivity has a much greater effect on resistance than a simple change in geometry and so a semiconductor can be used to create a much more sensitive strain gauge, though they are generally also more sensitive to environmental conditions (esp. temperature).

Sensor Basics: Capacitive Sensors

Capacitive sensors use the electrical property of "capacitance" to make measurements. Capacitance is a property that exists between any two conductive surfaces within some reasonable proximity.

Spacing variation[5]

Spacing variation of parallel plates is often used for motion detection if the spacing change is less than the electrode size. The parallel plate capacitance formula shows that capacitance is inversely related to spacing. This gives a conveniently large value of capacitance at small spacing, but it does often require signal conditioning which can compensate for the parabolic capacitance-motion relationship. This is easily done by measuring impedance rather than capacitance.

Area variation[5]

As these plates slide transversely, capacitance changes linearly with motion. Quite long excursions are possible with good linearity, but the gap needs to be small and well-controlled.

계측방법, Signal Conditioning[5]

An R-C relaxation oscillator such as the venerable 555 or its CMOS update, the 7555, converts capacitance change into a change of frequency or pulse width.The RC oscillator used with a spacing-variation capacitor will produce a frequency output which is linear with spacing, while an area-variation capacitor is linearized by measuring pulse width.

Sensor Basics: LVDT

LVDT (Linear Variable Differential Transformer)

A type of electrical transformer used for measuring linear displacement.

An LVDT Displacement Transducer comprises 3 coils; a primary and two secondaries.

http://www.rdpe.com/ex/hiw-lvdt.htm

Sensor Basics: Hall Effect

For a simple metal where there is only one type of charge carrier (electrons) the Hall voltage VH is given by

where I is the current across the plate length, B is the magnetic flux density, d is the depth of the plate, e is the electron charge, and n is the charge carrier density of the carrier electrons.

Hall probes are often used as magnetometers, i.e. to measure magnetic fields.

http://en.wikipedia.org/wiki/Hall_effect

Physics Animation Model The Hall-Effecthttp://www.youtube.com/watch?v=_ATDraCQtpQ

http://en.wikipedia.org/wiki/Hall_effect_sensor

A Hall effect sensor is a transducer that varies its output voltage in response to changes in magnetic field. Hall sensors are used for proximity switching, positioning, speed detection, and current sensing applications.

Sensor Basics: Piezoelectric Effect

Piezoelectricity is the charge which accumulates in certain solid materials (notably crystals, certain ceramics, and biological matter such as bone, DNA and various proteins) in response to applied mechanical strain.

http://en.wikipedia.org/wiki/Piezoelectric_sensor

A piezoelectric disk generates a voltage when deformed (change in shape is greatly exaggerated)

Sensor Basics: Piezoelectric Effect

Even though piezoelectric sensors are electromechanical systems that react to compression, the sensing elements show almost zero deflection.

Additionally, piezoelectric technology is insensitive to electromagnetic fields and radiation, enabling measurements under harsh conditions.

One disadvantage of piezoelectric sensors is that they cannot be used for truly static measurements.

http://en.wikipedia.org/wiki/Piezoelectric_sensor

Sensor Basics: Thermoelectric Effect

The thermoelectric effect is the direct conversion of temperature differences to electric voltage and vice versa. A thermoelectric device creates a voltage when there is a different temperature on each side.

At atomic scale (specifically, charge carriers), an applied temperature gradient causes charged carriers in the material, whether they are electrons or electron holes, to diffuse from the hot side to the cold side, similar to a classical gas that expands when heated; hence, the thermally induced current.

http://en.wikipedia.org/wiki/Seebeck_effect#Seebeck_effect

Sensor Basics: Thermoelectric Effect

The Seebeck effect is the conversion of temperature differences directly into electricity.

The effect is that a voltage, the thermoelectric EMF, is created in the presence of a temperature difference between two different metals or semiconductors. This causes a continuous current in the conductors if they form a complete loop. The voltage created is of the order of several microvolts per kelvin difference. One such combination, copper-constantan, has a Seebeck coefficient of 41 microvolts per kelvin at room temperature.

http://en.wikipedia.org/wiki/Seebeck_effect#Seebeck_effect

SA and SB are the Seebeck coefficients (also called thermoelectric power or thermopower) of the metals A and B as a function of temperature, and T1 and T2 are the temperatures of the two junctions.

The Seebeck effect is commonly used in a device called a thermocouple.

In physics, the Coriolis effect is an apparent deflection of moving objects when they are viewed from a rotating reference frame. In a reference frame with clockwise rotation, the deflection is to the left of the motion of the object; in one with anti-clockwise rotation, the deflection is to the right.

The vector formula for the magnitude and direction of the Coriolis acceleration is

where (here and below) ac is the acceleration of the particle in the rotating system, v is the velocity of the particle in the rotating system, and Ω is the angular velocity vector which has magnitude equal to the rotation rate ω and is directed along the axis of rotation of the rotating reference frame, and the ×symbol represents the cross product operator.

Sensor Basics: Coriolis Effect

http://en.wikipedia.org/wiki/Coriolis_effect

Sensor Basics: Coriolis Effect

coriolis effect (2-11)

http://www.youtube.com/watch?v=mcPs_OdQOYU

Foucault's pendulum - 2http://www.youtube.com/watc

h?v=wlhHWYKswik

자동차 센서의 요구사양 및 대응책 [6]

High Reliability Rugged, well-proven technology

Low manufacturing costs Efficient mass production

Severe operating condition Highly resistant packaging

Low volume Miniaturisation techniques

High accuracy Local fault compensation

자동차 센서: 종류

자동차 센서: 시장전망

MEMS (Micro Electro Mechanical System)

소형 경량화

기계식: 25mm MEMS: 소자 2~3mm, package 8~9mm [3]

MEMS: Capacitive Sensor

Parallel Plate Capacitor

http://www.eecs.berkeley.edu/~boser/pdf/

Transverse Comb

Parallel multiplates can to increase the sensor capacitance in a small volume.

http://www.capsense.com/capsense-wp.pdf

Transverse Comb

Signal Conditioning 통합

ADXL 50 Layout

http://www.eecs.berkeley.edu/~boser/pdf/overview.pdf

MEMS [3]

압력센서

실리콘 다이어프램(diaphragm)형 압력센서는 외부 압력에 의한 다이어프램의 휨 정도 계측

MEMS [3]

압력센서

장점 단점

1) 정전용량형

(capacitive)

온도 계수 낮고,

전력 손실이 적음

소자 면적이 넓고,

복잡한 신호처리부 필요

2) 압저항형

(piezo-resistive)

선형성 우수,

신호처리 용이

감도 낮으며,

온도 의존성 높음

MEMS [3]

압력센서

MEMS [3]

가속도 센서

MEMS [3]

가속도 센서

장점 단점

1) 기계식

구조가 복잡하고

크고 무거우며

양산이 힘들어

2) 실리콘

기계적 성질이 우수하여

기존에 확립된 반도체 집적 회로 공정 기술을이용함으로써

신뢰성과 양산성을 향상시킬 수 있으며

소자의 소형화, 경량화 및 저가격화가 가능

MEMS [3]

가속도 센서

MEMS [3]

각속도 센서 (Yaw-rate Sensor)

• 코리올리 효과 (Coriolis effect) 이용

The ADXRS gyros take advantage of this effect by using a resonating mass analogous to the person moving out and in on a rotating platform. The mass is micromachined from polysilicon and is tethered to a polysilicon frame so that it can resonate only along one direction.

http://www.analog.com/library/analogdialogue/archives/37-03/gyro.html

Figure 3 shows that when the resonating mass moves toward the outer edge of the rotation, it is accelerated to the right and exerts on the frame a reaction force to the left. When it moves toward the center of the rotation, it exerts a force to the right, as indicated by the orange arrows.

To measure the Coriolis acceleration, the frame containing the resonating mass is tethered to the substrate by springs at 90° relative to the resonating motion, as shown in Figure 4. This figure also shows the Coriolis sense fingers that are used to capacitively sense displacement of the frame in response to the force exerted by the mass, as described further on.

Figure 4. Schematic of the gyro’s mechanical structure.

Figure 5. The frame and resonating mass are displaced laterally in response to the Coriolis effect. The displacement is determined from the change in capacitance between the Coriolis sense fingers on the frame and those attached to the substrate.

Figure 6. Photograph of mechanical sensor. The ADXRS gyros include two structures to enable differential sensing in order to reject environmental shock and vibration.

Figure 7. Photograph of ADXRS gyro die, highlighting the integration of the mechanical rate sensor and the signal conditioning electronics.

센서 네트워크 기술 [4]

센서 네트워크

• 특정 지역에 소형의 노드를 설치하여 주변 정보 또는 특정 목적의 정보를 획득하고

베이스 스테이션에서 이 정보를 수집하여 이를 활용하기 위한 서비스 네트워크

• 상호간의 정보 전달보다는 자동화된 원격정보의 수집을 목적으로 하는 점에서 기존

네트워크와 구별

• USN (Ubiquitous Sensor Network): 여러 개의 센서 네트워크 필드(field)가 게이트

웨이(gateway)를 통해 외부 네트워크와 연결되어 있는 구조

자동차 센서 네트워크

• 자동차 전자장치의 증가 복잡한 배선, 무게 증가 연비 저하, 고장 발생 비율

증가

• 이러한 문제를 개선하기 위하여 수많은 배선들을 몇 가닥의 통신 라인으로 대체하

여 대량의 정보를 고속으로 처리할 수 있도록

자동차 센서 네트워크

산소센서: Catalytic Converter (촉매 변환 장치)

A three-way catalytic converter has three simultaneous tasks:

http://en.wikipedia.org/wiki/Catalytic_Converter

Metal-core converter

Ceramic-core converter http://www.bladeyourride.com/how-to-take-care-of-your-catalytic-converter/

산소센서

이론 공연비 (Optimum air fuel ratio)

14.7:1

http://www.originlab.com/index.aspx?go=Solutions/CaseStudies&pid=227

산소센서

http://ecohho.wordpress.com/what-is-hho/hydrogen-fuel-on-demand/unleash-the-true-power-of-water/understanding-an-efie/understanding-an-o2-oxygen-sensor/

산소센서

배기가스대책 시스템에서는 산소와 삼원촉매를 이용하여 NOX, HC, CO 등의 유해배

기가스를 사람에게 해가 없는 N, H2O, CO2로 변화시키므로 유해배출가스를 감소시키

려면 이론 공연비의 과부족이 없어야 한다.

삼원촉매를 이용하여 NOX를 환원하면 질소(N)와 산소(O2)로 분해되고, HC와 CO는

산화되어 물과 CO2로 변화하는데,

이론 공연비보다 희박하면 산소가 많아져 NOX가 환원되지 않고,

이론 공연비보다 농후하면 산소가 부족하여 HC와 CO가 산화되지 않으므로

공연비를 항상 이론 공연비인 14.7:1부근으로 제어하기 위해 센서가 산소 센서이다.

양민복, 미래형 자동차, 인터비젼

산소센서

Zirconia sensor 기전력

Titania sensor 가변저항

http://en.wikipedia.org/wiki/Oxygen_sensor

산소센서

Zirconia sensor

The zirconium dioxide, or zirconia, lambda sensor is based on a solid-state electrochemical fuel cell called the Nernst cell. Its two electrodes provide an output voltage corresponding to the quantity of oxygen in the exhaust relative to that in the atmosphere.

http://www.vcoa.org/700-900-faq/EngineSensors.html

산소센서

Titania sensor

A less common type of narrow-band lambda sensor has a ceramic element made of titanium dioxide (titania). This type does not generate its own voltage, but changes its electrical resistance in response to the oxygen concentration.

http://blog.naver.com/PostView.nhn?blogId=autokyw&logNo=70044118012

공기량 센서 (Airflow Sensor)

http://en.wikipedia.org/wiki/Mass_flow_sensor

• Vane meter sensor (VAF sensor)

• Hot wire sensor (MAF)

• “Coldwire" sensor

• Kármán vortex sensor

http://www.aa1car.com/library/vaf_sensors.htm

Vane meter sensor (VAF sensor)

Hot wire sensor (MAF)

The theory of operation of the hot wire mass airflow sensor is similar to that of the hot wire anemometer (which determines air velocity).

This is achieved by heating a wire with an electric current that is suspended in the engine’s air stream, like a toaster wire.

The wire's electrical resistance increases as the wire’s temperature increases, which limits electrical current flowing through the circuit. When air flows past the wire, the wire cools, decreasing its resistance, which in turn allows more current to flow through the circuit. As more current flows, the wire’s temperature increases until the resistance reaches equilibrium again.

The amount of current required to maintain the wire’s temperature is directly proportional to the mass of air flowing past the wire.The integrated electronic circuit converts the measurement of current into a voltage signal which is sent to the ECU.

Kármán vortex sensor

A Kármán vortex sensor works by setting up a laminar air stream. The air stream is disrupted by a vertical bow in the sensor. This causes a wake in the air stream and subsequently the wake will collapse repeatedly and cause Kármán vortexes. The frequency of the resulting air pressure oscillation is proportional to the air velocity.

These vortexes can either be read directly as a pressure pulse against a sensor, or they can be made to collide with a mirror which will then interrupt or transmit a reflected light beam to generate the pulses in response to the vortexes. The first type can only be used in pull thru air (prior to a turbo- or supercharger), while the second type could theoretically be used push or pull thru air (before or after a forced induction application like the previously mentioned super- or turbocharger). Instead of outputting a constant voltage modified by a resistance factor, this type of MAF outputs a frequency which must then be interpreted by the ECU.

광학식 이산화탄소 농도 센서

NDIR 방식 이산화탄소 가스센서 [1]

• 이산화탄소가 4.26um 대역의 파장을 흡수하는 성질 이용

http://v2010.raesystems.com/~raedocs/App_Tech_Notes/Tech_Notes/TN-169_NDIR_CO2_Theory.pdf

광학식 이산화탄소 농도 센서

NDIR 방식 이산화탄소 가스센서 [1]

• NDIR (Non-Dispersive Infrared)

참고자료

1. 조남규, “자동차의 전자화 추세 및 소요센서 전망,” Auto Journal 2008.06, pp. 36-42.

2. 김시동, 김병우, “자동차 환경센서 기술 동향,” Auto Journal 2008.06, pp. 22-28.

3. 권재홍, 조우성, 김정훈, 김영훈, 주병권, “MEMS 기술을 적용한 자동차 응용 센서기술 및 동향,” 주간기술동향 통권 1284호 2007.2.21, pp. 21-36.

4. 심영일, “새롭게 발전하는 자동차 센서 네트워크기술,” Machinery Industry, 2008.3, pp. 66-73, 온라인 자료 http://www.koami.or.kr/webzin/2k803/8.pdf.

5. L. K. Baxter, “Capacitive Sensors,” 온라인 자료 http://www.capsense.com/capsense-wp.pdf

6. 임시형, “Automotive Sensors and Measurements,” 섀시 전기전자제어, 2010년 자동차 전

문기술교육 자료, ㈜엔지비, 2010년.

자동차센서 · 2014. 12. 29. · The gauge is attached to the object by a suitable adhesive,...

Documents

Double Object Constructions ― Against the Small …ousar.lib.okayama-u.ac.jp/files/public/5/55784/...Double Object Constructions -Against the Small Clause Analysis- Masahiro Kawakami

Questioning the art object 2: Sol LeWitt

Modern Algebra and the Object/Operation - Ircamrecherche.ircam.fr/equipes/repmus/moreno/AndreattaIowaAtonal.pdf · Modern Algebra and the Object/Operation duality in music Moreno

Scattering of kinks of the sinh-deformed model · PDF fileScattering of kinks of the sinh-deformed ’4 model Dionisio Bazeia,a Ekaterina Belendryasova,b Vakhid A. Gani,b;c;1 aDepartamento

Collective modes of excitation in deformed neutron-rich nuclei

Lesson 5: The JavaScript Document Object Model (DOM) · Dot notation b. The with statement c. The write() method d. ... Which property is associated with the document object? a. name

Rotation - physics.unsw.edu.aujw/1131/rotationnotes.pdf · I ≡ Mk2 defines the radius of gyration k k is the radius of a hoop with the same I as the object in question object I

On Gaussian Fluctuations for Deformed Wigner Matrices · X n √ n + 1 nα/2 ... 1.4 CLT • 2.Deformed Wigner Matrices 2.1 Average Spectral Distribution 2.2 The Largest Eigenvalue

The Object of the investigation is a syndrome of “professional burnout” during the teacing

The Sierpinski Object in the Scott Realizability Toposooste110/realizability/s... · 2020. 7. 28. · in this topos is the exponential N, where Nis the natural numbers object. We

Sp - pdfMachine from Broadgun Software, ... · (b)Field force : Force which acts on an object at a distance by the interaction of the object with the field produced by other object

Title Deformed free probability of Voiculescu (Infinite ... · Title Deformed free probability of Voiculescu (Infinite Dimensional Analysis and Quantum Probability Theory) Author(s)

The Ninth Visual Object Tracking VOT2021 Challenge Results

Learning the Relative Pronoun (Object)

SPL/T - The object social network

The Design and Implementation of Object-Constraint Programming

pepa.holla.cz · 2016. 8. 14. · the principles of object-oriented javascript zakas nicholas c. zakas javascriptjavascript object-orientedobject-oriented the principles ofthe principles

CIHA2012 The Challenge of the Object - GBV · The Challenge of the Object ... Anthropology in Vancouver Maureen Murphy 401 ... Impossibility of a Lasting Context for a Work,

Sequential granite emplacement: a structural study of the late … · 2017-08-28 · During the Variscan orogeny, the rocks of both units were metamorphosed and deformed, and the

Verma modules for the Virasoro algebra · Representation Theory Future Research Ultimate goal: do the above for more complicated q-deformed Heisenberg-Virasoro algebra. Main problem: