View
223
Download
0
Category
Preview:
Citation preview
Se.FaPRODUZIONE DI ARTICOLI IN GOMMA
RUBBER PRODUCTS
1992-201220 years of quality
made in italy
Se.Fa - Produzione di articoli in gomma
ABOUT SE.FA
CHI SIAMODalla formulazione e produzione dei compound allo stampaggio di articoli tecnici in gomma. Se.Fa si è costituita nel corso dei primi anni ‘90. Attraverso le competenze tecnologiche, tecnico-progettuali e produttive presenti, Se.Fa è attualmente in grado di soddisfare clienti di primaria importanza che operano sul mercato sia nazionale che estero, in diversi settori, tra cui quello idraulico, veicolistico e del riscaldamento.
From compounds formulation and production to rubber technical articles moulding.Se.Fa was founded during the early 90s. Our technological, technical-design and production experience makes Se.Fa able to meet the needs of leading companies operating on both the national and international market, in several areas, including the hydraulic, automotive and heating sectors.
Se.Fa dispone di una gamma di prodotti molto completa, realizzata in vari tipi di gomma: NR, SBR, EPDM, Butile, Silicone e Viton che vende direttamente sul mercato nazionale ed estero. I principali prodotti sono: membrane per autoclavi e vasi d’espansione, guarnizioni per caldaie e canne fumarie, antivibranti “automotive”.
Se.Fa has a whole range of products, produced in several types of rubber: NR, SBR, EPDM, Butyl, Silicon and Viton.The main products are: membranes for pressure tanks and expansion vessels, seals for boilers and chimney flues that Se.Fa sells directly to national and foreign markets.
PRODOTTI
PRODUCTS
Se.Fa - Rubber products
Se.Fa’s production area is developed on a surface of more than 3.000 square meters. All Se.Fa’s press machines are very recent and produced according to the best efficiency and safety standards. These machines have a very powerful closing strength and injection capacity (up to 900 tons and a 12,5 lts capacity), with moulding planes up to 1600 mm x 1100 mm.
L’area produttiva di Se.Fa si sviluppa su di una superficie di oltre 3.000 mq. Le nostre presse sono tutte molto recenti e quindi costruite secondo i migliori criteri di efficienza e sicurezza. Sono macchine con forza di chiusura e capacità di iniezione alte (fino a 900 ton e capacità di 12,5 litri) e con piani di stampaggio fino a 1600 mm x 1100 mm.
CICLO PRODUTTIVOIl laboratorio è un luogo fondamentale per il controllo della qualità dei prodotti Se.Fa.I controlli avvengono in un primo momento sulle mescole, con lo scopo di individuare la qualità del materiale e le ottimali condizioni di stampaggio, poi sui prodotti stampati al fine di verificare le caratteristiche fisiche e meccaniche (allungamento, compressione, durezza).In laboratorio vengono anche effettuati dei controlli relativi alla resistenza al calore, al contatto con acqua e altri liquidi, all’allungamento ciclico.
LABORATORIO
The laboratory is an important place to test the quality of Se.Fa products. The controls take place at first on the compounds to identifying the quality of the material and the optimal moulding conditions, then on the final products in order to verify the physical characteristics and mechanical properties (elongation, compression, hardness). In the laboratory are also made controls related to resistance to heat, to contact with water and other fluids, and to cyclic elongation.
LABORATORYPRODUCTION CYCLE
Se.Fa - Produzione di articoli in gomma
CAPACITÀ MEMBRANE MEMBRANES VOLUME
FLANGIAFLANGE mm
LUNGHEZZALENGHT mm
DIAMETRODIAMETER mm
2/3 LT 45/65 135 805/8 LT 45/65 155 1058/12 LT 45/65 200 11512/18 LT 45/65 265 13524 LT(s) 80/110 260 20024 LT (b) 90/120 260 20035/50 LT (s) 80/110 335 21035/50 LT (b) 90/120 335 21040/60 LT 80/110 425 17050/80 LT 80/110 500 22060/80 LT 90/120 665 235100 LT 90/120 785 235
Se.Fa realizza membrane per serbatoi per acqua calda e fredda, per acque sanitarie e per osmosi inversa. Le membrane, che sono il cuore del serbatoio, sono prodotte a sacco e a doppio volume.
MEMBRANE PER AUTOCLAVI E VASI D’ESPANSIONE
MEMBRANES FOR PRESSURE TANKS AND EXPANSION VESSELS Se.Fa produces membranes for cold and hot watertanks, for sanitary water and reverse osmosis. The membranes, which are the heart of the tank, are produced in bag shape and in double volume.
CAPACITÀ MEMBRANEMEMBRANES VOLUME
FLANGIAFLANGE mm
LUNGHEZZALENGHT mm
DIAMETRODIAMETER mm
80/100 LT 80/110 630 120/140100/150 LT 80/110 730 180/270150/200 LT (s) 80/110 810 240/270150/200 LT (b) 150/200 810 240/270200/300 LT 150/200 1000 230/380500/750 LT 150/200 1350 280/440750/1000 LT 150/200 1800 340/4701000/1500 LT 200/260 2100 420/500
La forma a doppio volume consente alla membrana di ottimizzare il suo funzionamento all’interno del serbatoio.
Double volume shape allows membranes to optimize its job inside the tank.
MEMBRANA A SACCO - BAG MEMBRANES
MEMBRANA DOPPIO VOLUMEDOUBLE VOLUME MEMBRANES
1000/1500 LT
500/750 LT
200/300 LT
100/150 LT
Se.Fa - Rubber products
MEMBRANA DI GRANDI DIMENSIONI BIG SIZE MEMBRANES
Membrane per serbatoi da 2000 lt – 3000 lt – 5000 lt
La membrana può esser prodotta con misure specifiche alla necessità del serbatoio:
- 1 o 2 flange (diam. 80, diam. 150, diam. 250)
- 3 diversi tipi di flangia (small, medium, big)
- lunghezza variabile da 1,75 mt a 3,0 mt
Membranes for 2000 lt – 3000 lt – 5000 lt tanks
The membrane can be produced with specific measures to the needs of the tank:
- 1 or 2 flanges (diam. 80, diam. 150, diam. 250)
- 3 different flange type (small, medium, big)
- variable length from 1,75 mts to 3,0 mts87
5
1750-3000
FLANGE DM:SMALL 150/200 mmMEDIUM 200/260 mmBIG 260/315 mm
---
*
*
Se.Fa - Produzione di articoli in gomma
ALTRI ARTICOLI TECNICI - OTHER TECHNICAL ARTICLES
Elementi isolanti per quadri e interruttori elettrici Insulators for switchgear and electrical switches
Boccole antivibranti per barre stabilizzatrici di autoveicoliAnti–vibration bushings for vehicles stabilizer bars
Membrane per vasi d’espansione per riscaldamento e anti colpo d’arieteMembranes for heating expansion vessels and anti-hammer water tanks
QUALE ARTICOLO TI PIACEREBBE TROVARE QUI?WHICH ARTICLE WOULD YOU LIKE TO FIND HERE?
?Scrivi alla nostra e-mail
Write to our e-mail
info@sefasrl.com
Se.Fa - Rubber products
GUARNIZIONI PER CAMINI GASKETS FOR CHIMNEY
I nostri prodotti per il settore riscaldamento sono:
- Guarnizioni per caldaie murali- Guardnizioni per tubi di aspirazione e canne fumarie (resistenza a fiamma e agenti chimici)
I prodotti realizzati da Se.Fa trovano impiego nel delicato settore della evacuazione dei fumi prodotti dalla combustione del gas nelle caldaie.La gamma di prodotti di Se.Fa prevede: guarnizioni di tenuta tubo/tubo o tubo/curva; manicotti per fascette di raccordo; rosoni coprimuro.Le guarnizioni sono prodotte in Silicone e EPDM (caldaie a condensazione) secondo quanto stabilito dalle più recenti normative e quindi offrono le migliori garanzie di resistenza e di tenuta nel tempo ad alte temperature (fino a 200°C).La gamma di guarnizioni è completa e può essere applicata a tubi con diametri da 60 a 350 mm.
Se.Fa’s products for heating are:
- Boilers Seals- Chimney Seals (high temperature and chemical agents resisteance)
The Se.Fa products are used in the sensitive sector of smoke evacuation produced by the combustion of gas in boilers.Se.Fa’s range of products includes: seals pipe/pipe or pipe/bends; sleeves for connecting clamps; wall covering plates.The seals are produced in Silicon and EPDM (condensation boilers) according to the most recent standards, therefore they offer better resistance guarantees and better long-life to high temperatures over time (up to 200°C).Our range of gaskets is complete and can be applied to pipes with diameters from 60 to 350 mm.
Se.Fa - Produzione di articoli in gomma
La forma delle guarnizioni consente, per la presenza di 2 o 3 labbra, grande facilità in fase di innesto dei tubi e massima garanzia di tenuta dei fumi.Le guarnizioni Se.Fa sono prodotte secondo quanto stabilito dalla normativa EN 14241-1:2005 in termini di resistenza alle temperature ed alla condensa acida.Il rispetto di questa norma è garanzia fondamentale per la corretta evacuazione dei fumi di combustione delle caldaie.I materiali usati permettono un impiego in diversi campi di applicazione e a diverse condizioni:
1. EPDM con elevate caratteristiche meccaniche, buona resistenza a temperatura fino a 120°C2. Silicone con moderata resistenza ad acidi e a temperature fino a 250°C3. Fluoroelastomero (Viton) con elevata resistenza ad acidi aggressivi e a temperature molto elevate fino a 350°C
The gasket shape allows , thanks to their 2 or 3 lips, great ease during engagement of the tubes and maximum guarantee sealing of the fumes. The gaskets are produced by Se.Fa as defined in EN 14241-1:2005 regulation in terms of temperature resistance and acid condensation.Compliance with this regulation is the fundamental guarantee for the proper discharge of boilers flue gases.The materials used allow to employ gaskets in various application fields and different conditions:
1. EPDM with high mechanical characteristics, good resistance to temperature up to 120 ° C2. Silicone with moderate resistance to acids and temperatures up to 250 ° C3. Fluoroelastomer (Viton) with high resistance to aggressive acids and high temperatures up to 350 ° C
Se.Fa - Rubber products
DESCRIZIONEDESCRIPTION
MATERIALECOMPOUNDS
COLORICOLORS
DIAMETRI DIAMETERS
GUARNIZIONE SPALLA 9 - 3 LABBRAGASKET HEIGHT 9 - 3 LIPS
EPDM/SILICONEEPDM/SILICON
Blue, rosso, neroBlue, red, black
60 – 80 – 100 – 110 – 120 – 125 – 130 – 140 – 150 – 160 – 180 – 200 – 220 – 230 – 250 – 300 – 350
GUARNIZIONE SPALLA 12 - 3 LABBRAGASKET HEIGHT 12 - 3 LIPS
8EPDM/SILICONEEPDM/SILICON
Blue, rosso, neroBlue, red, black
80 – 100 – 110 – 120 – 130 – 140 – 150 – 160 – 180 – 200 – 220 – 230 – 250 – 300 – 350
GUARNIZIONE SPALLA 10 - 2 LABBRAGASKET HEIGHT 10 - 2 LIPS
EPDM/SILICONEEPDM/SILICON
Blue, rosso, neroBlue, red, black
80 – 100 – 110 – 120 – 130 – 140 – 150 – 160 – 180 – 200 – 220 – 230 – 250 – 300 – 350
GUARNIZIONE SPALLA 12 - 2 LABBRAGASKET HEIGHT 12 - 2 LIPS
EPDM/SILICONEEPDM/SILICON
Blue, rosso, neroBlue, red, black
80 – 100 – 110 – 120 – 130 – 140 – 150 – 160 – 180 – 200 – 220 – 230 – 250 – 300 – 350
ROSONE COPRIMUROWALL COVERING PLATE
EPDM Bianco, grigio/White, grey 60 – 80 – 100 – 110 – 125
ROSONE COPRIMUROWALL COVERING PLATE
SILICONE/SILICON Bianco, nero/White, black 60 – 80 – 100 – 110 – 125
MANICOTTO PER FASCETTESLEEVE FOR CONNECTING CLAMPS
EPDM Bianco/White 80/80 – 94/100 – 100/100
TIPOLOGIE GUARNIZIONI – ROSONI – MANICOTTITYPES OF SEALS – PLATES – SLEEVES
Se.Fa - Produzione di articoli in gomma
CERTIFICAZIONI CERTIFICATIONSSe.Fa ha attribuito grande importanza all’ottenimento di certificazioni sia del sistema di qualità aziendale, sia della qualità del prodotto.Alcuni tra i principali prodotti Se.Fa sono particolarmente sensibili nei confronti della salute e sicurezza della collettività: le membrane per autoclavi possono essere impiegate per la distribuzione di acque ad uso potabile, mentre le guarnizioni per camini e canne fumarie sono un elemento fondamentale per la corretta evacuazione dei fumi di combustione delle caldaie.Se.Fa dispone di diversi attestati, tra cui i principali sono:
• Certificato del Sistema di Qualità ai sensi della norma UNI EN ISO 9001:2008 (TUV –Sud)
• Certificato di conformità delle guarnizioni per camini e canne fumarie ai sensi della norma EN 14241-1:2005 E (IMQ)
• Certificato della produzione di membrane per autoclavi e vasi d’espansione ai sensi della norma DIN4807-3 (TUV-Sud)
• Certificati di idoneità delle membrane per autoclavi e vasi d’espansione al contatto con acqua per uso potabile ai sensi delle seguenti norme:
• Decreto ministeriale nr 174 del 06/04/2001• ACS - Francia “Attestation de conformité sanitaire” • ( CARSO)• NSF - FDA (NSF International)• WRAS – British Standard 6920-1:2000• KTW (TZW)• PAH
• PSB
Se.Fa has conferred a great importance in gaining certifications on both company’s quality policy and products’ quality.Some of main Se.Fa products are particularly notable towards common health and safety: membranes for pressure tanks can be used to distribute drinkable water, while seals for chimneys and chimney flues are a key element for the proper evacuation of flue gas from boilers.Se.Fa obtained several certificates, issued by major international institutions, amongst them:
• Quality Company System Certificate according to UNI EN ISO 9001:2008 regulation (TUV –Sud)
• Conformity Certificate of seals for Chimney and Chimney Flues according to EN 14241-1:2005 E regulation (IMQ)
• Membranes Production Certificate for rubber tanks and expansion vessels according to DIN4807-3 regulation (TUV-Sud)
• Suitability Certificate for membranes for rubber tanks and expansion vessels to the contact witn drinkable water according to the following regulations:
• Ministerial Decree nr 174 dd 06/04/2001• ACS - Francia “Attestation de conformité sanitaire” • ( CARSO)• NSF - FDA (NSF International)• WRAS – British Standard 6920-1:2000• KTW (TZW)• PAH• PSB
Se.Fa - Rubber products
Se.Fa - Produzione di articoli in gomma
TURKEYSEFA KAUÇUK SANAYİ VE TİC. LTD. ŞTİ.Körfez Mah. Hikmet Erenkaya Sit. A Blok No. 11/2 İzmit / KOCAELİ
Tel. +90 262 3354438Fax +90 262 33544390sefakaucuk1@sefasrl.com www.sefasrl.com
ITALIASe.Fa SrlVia del Lavoro, 948124 - Sant’Alberto (RA) Ravenna
Tel. +39 0544 528784Fax +39 0544 528840 info@sefasrl.com www.sefasrl.com
Se.FaProduzione di articoli in gomma Rubber products Ravenna
İzmit
Recommended