View
895
Download
81
Category
Preview:
DESCRIPTION
Using Site See for MapInfo
Citation preview
Creating Site Map Files through Sitesee Tool For internal use only
Creating Site Map Files Through SiteSee Tool
Prepared by Tan zhiwei Date 2005-11-23
Reviewed by Date
Reviewed by Date
Granted by Date
Huawei Technologies Co., Ltd.
All rights reserved.
2008-01-21 All rights reserved Page 1 of 11
Creating Site Map Files through Sitesee Tool For internal use only
Table of Contents
1 Adding SiteSee Tool to Mapinfo.........................................................................................4
2 Creating Site Data................................................................................................................6
3 Creating Site Map Files........................................................................................................7
4 Creating Sector Map Files...................................................................................................8
5 Site Map Display..................................................................................................................10
2008-01-21 All rights reserved Page 2 of 11
Creating Site Map Files through Sitesee Tool For internal use only
List of Figures
Figure 1-1 Tool Manager dialog box....................................................................................4
Figure 1-2 Selecting SiteSee tool to be added in the Tool Definition...................................5
Figure 1-3 Tool Manager dialog box settings.......................................................................5
Figure 1-4 Table->WFI SiteSee...........................................................................................6
Figure 3-1 Site data settings................................................................................................7
Figure 3-2 Create Points items............................................................................................8
Figure 3-3 Symbol Style items.............................................................................................8
Figure 4-1 SiteSee settings.................................................................................................9
Figure 5-1 Site map display...............................................................................................10
2008-01-21 All rights reserved Page 3 of 11
Creating Site Map Files through Sitesee Tool For internal use only
The software version used for the operations is Mapinfo7.0 (English version),
and the 7.0 SiteSee tool (Chinese version) is unavailable. The SiteSee tool is not
used in Mapinfo5.0 version.
1 Adding SiteSee Tool to Mapinfo
To add the SiteSee tool to Mapinfo, do as follows:
1) Select Tools -> Tool Manager… in the Mapinfo menu, and then click Add
Tool, as shown in Figure 1-1.
Figure 1-1 Tool Manager dialog box
2) In the pop-up dialog box, do the following operations, as shown in Figure 1-
1:
a) In the Title column, set the tool name.
b) In the Location column, click the button in the right to select the path
where Sitesee.MBX is located.
SiteSee file:
c) Click OK.
2008-01-21 All rights reserved Page 4 of 11
Creating Site Map Files through Sitesee Tool For internal use only
Figure 1-1 Selecting SiteSee tool to be added in the Tool Definition
3) Return to the Tool Manager dialog box, as shown in Figure 1-1. In the
Tools list, there is Sitesee. Tick off the Loaded and Autoload. ”Loaded”
means that you can load the SiteSee tool immediately. ”Autoload” means
the SiteSee tool is loaded automatically when you start the Mapinfo
software.
Figure 1-1 Tool Manager dialog box settings
4) Click OK, as shown in Figure 1-1, and then select Table -> WFI SiteSee.
2008-01-21 All rights reserved Page 5 of 11
Creating Site Map Files through Sitesee Tool For internal use only
Figure 1-1 Table->WFI SiteSee
2 Creating Site Data
Similar to the site data in the following attachment, SiteNum, SectorName,
BSName, Longitude, Latitude, Azimuth, and Width of Wave Petal are mandatory
items.
The attachment is saved as a file in the format of .txt.
In the above-mentioned mandatory items, SiteNum can be BSName or CellID,
which is used to identify uniquely a BTS, but the item should be in the front of the
column.
BSName and SectorName are actually not mandatory items. For the purpose of
labeling a BTS and sector, these items are recommended. SectorName can be
replaced with SectorID.
2008-01-21 All rights reserved Page 6 of 11
Creating Site Map Files through Sitesee Tool For internal use only
3 Creating Site Map Files
To create site map files, do as follows:
1) Select File -> Open, and open the site data file (in .txt format). A dialog box
is displayed, as shown in Figure 1-1. Do the following settings:
a) In the Delimiter column, select Tab.
b) In the File Character Set drop-down list, select No character set
conversation. Other items may not support the Chinese interface.
c) Tick off Use First Line for Column Titles.
d) Click OK.
Figure 1-1 Site data settings
2) Select Table -> Create Points…, as shown in Figure 1-1. Do the following
operations:
a) Click the button in the right of using Symbol. In the pop-up dialog
box, as shown in Figure 1-2, set the site display attributes, including
Font, Symbol, and Color.
b) In the Get X… drop-down list, select Longitude.
c) In the Get Y… drop-down list, select Latitude.
2008-01-21 All rights reserved Page 7 of 11
Creating Site Map Files through Sitesee Tool For internal use only
d) Click OK. The site map files are created. Under the directory where
site data file (in .txt format), there are three site map files in the
format of .TAB, .ID, and .Map.
Figure 1-1 Create Points items
Figure 1-2 Symbol Style items
4 Creating Sector Map Files
To create sector map files, do as follows:
2008-01-21 All rights reserved Page 8 of 11
Creating Site Map Files through Sitesee Tool For internal use only
3) Select File -> Open, and open the site data file (in .txt format). A dialog box
is displayed, as shown in Figure 1-1.
4) Select Table -> WFI SiteSee -> Create Site Boundaries, and then do the
following operations, as shown in Figure 1-1:
a) In the Site Latitude from column, select Latitude.
b) In the Site Longitude from column, select Longitude.
c) In the Site radius from column, set the sector map display radius.
d) Tick off Use Site Sectorization.
e) In the Beamwidth from Column, set the sector map display
beamwidth. Generally, the sector horizontal beamwidth is
recommended.
f) In the Orientation from Column, set the sector display orientation.
Generally, set Azimuth_degree.
g) Click OK.
h) In the pop-up dialog box, type the sector map filename, such as
”Lankabell Sector”. Under the corresponding directory, four files in the
formats of .DAT, .TAB, .ID, and .Map are displayed.
2008-01-21 All rights reserved Page 9 of 11
Creating Site Map Files through Sitesee Tool For internal use only
Figure 1-1 SiteSee settings
5 Site Map Display
Select File -> Open, and open the created Site and Sector map files (in the
format of .TAB).
The site map is displayed, as shown in Figure 1-2.
2008-01-21 All rights reserved Page 10 of 11
Creating Site Map Files through Sitesee Tool For internal use only
Figure 1-2 Site map display
2008-01-21 All rights reserved Page 11 of 11
Recommended