View
6.441
Download
0
Category
Preview:
Citation preview
Say YES/NO to PLASTIC
EtymologyThe word plastic is derived from
the Greek (plastikos) meaning capable of being shaped or moulded, from (plastos) meaning moulded. It refers to their malleability, or plasticity during manufacture, that allows them to be cast, pressed, or extruded into a variety of shapes — such as films, fibres, plates, tubes, bottles, boxes, and much more.
Introduction What is Plastic?
Plastic are materials formed by long chains of carbon and hydrogen called polymers, formed by units called monomers. The most important characteristic of plastic is the capacity of deformation.
Origin of PlasticMost of the plastics are made up from
these three raw materials:
• Non – Renewable• Natural ResourcePetroleum
• Non – Renewable• Natural ResourceCoal
• Non – Renewable• Natural ResourceCellulose
Plastics
Production of Plastics
Plastics are made from fossil fuels.Fossil fuels contains hydrocarbons, which provide small building blocks called monomer.These hydrocarbons monomers are link together to form long carbon chains called polymers.The process of forming long molecules is called polymerization.The polymerization form viscous, sticky substances known as resins, which are used to make plastic products.These joined molecules form a plastic resin known as polythene.
Properties of Plastic Plastics are strong , light weight, flexible
and durable. Plastics can be easily moulded into a
variety of shapes and sizes. Plastics have excellent mechanical
strength (tensile properties, tear resistance, and impact resistance).
Plastics are relatively cheaper than compared to metals like steel, tin etc.
Plastics are reusable and recyclable. Plastics have long use age life.
Positive Aspects of Plastic
Plastics are good electricity and heat insulators.
Plastics do not corrode or decay.Plastics are cheap and
dispensable.Plastics are resistant to
chemicals, water or grease.
Categories of plastic
World Status – Plastic production and
disposalPlastic production
100 million tonnes/year
Annual increase of Production = 9%
Plastic waste disposal
25 million tonnes/year
Plastics in municipal solid
waste = 11.8% By weight
Classification of Plastic
Groups of Plastic
ThermoplasticsThermoplastics can
be repeatedly softened by heating
and hardened by cooling.
E.g. Polythene.
ThermosettingThermosetting plastics harden
permanently after being heated once.
e.g. Bakelite.
Sources of Plastic Waste
Agriculture7%
Transport8%
Furniture/Houseware8%
Electrical and Electronics8%
Building and Construction
23%
Packaging35%
Footwear1%
Medical2%
Mechanical Engineering2%
Toys/Sports3%
Other3%
Percentage of Plastic used in different fields
Plastic Pollution in India 80% of thermoplastics, and 20% of
thermo set plastic wastes are generated in India.
The use of plastics in India is 3kg per person per year.
The total consumption of plastic in India is about 4 million tonnes and the waste generated is about 2 million tonnes.
About 20% of solid municipal wastes are plastics in India.
Negative impacts of plastic on Land
Plastic pollution on land is both physical and chemical.
Plastic reduces soil fertility by forming the part of manure for years.
Plastic spoil environmental aesthetics and hygiene.
Plastics in soil can lessen the growth of plants and trees by blocking the absorption of minerals, water and other nutrients.
Management Options Disposing of plastic waste is trickier than
dealing with other traditional landfill material. Not only does plastic take thousands of years to break down, it can leach dangerous poison into the environment. Plastic is not going away, but how plastic waste is managed is becoming more sophisticated. Managing plastic waste starts at home with the consumer, but ultimately depends on governments around the world as well.
Life cycle stages of plastic
Manufacture Of plastics Use of plastics Disposal of
plastics
Toxic By products/
waste
Leaching of chemicals&
Enter human Food chain
recycling
Land fills
incinerationdistribution End of life
Negative impacts of plastics in air
Industries emit large amounts of carbon monoxide, dioxin and hydrogen cyanide.
These gaseous pollutants contaminate air and causes respiratory diseases, nervous system disorders and immune suppression in human beings.
Negative impacts of plastics on fresh water
Plastics wastes dumped in water courses contaminate and poisons freshwater life.
On leaching in water, plastic can easily enter the human food chain and harm human health.
Plastic debrises clog the sewage drains and create stagnant water which will be an ideal habitat for mosquitoes and other parasites.
Chocked drains cause flooding during monsoons.
Negative impacts o plastics on marine life
Discarded Plastic usually ends up within marine sources. The Pacific Ocean has one of the largest dumping ground for plastics, unknown numbers of sea birds marine mammals and fish ingest plastics which causes a variety of negative health effects and leading to their deaths.
Effects of plastics on marine life includes entanglement and ingestion of plastics debris by marine vertebrates.
Plastic is mistaken for food and is eaten up by birds, turtles, seals, and whales. This may choke them, or impede digestion and causing starvation.
Negative impacts of plastic on human health
Toxic chemicals contained in plastics cause neurological problems, cancer, birth defects, hormonal changes gastric ulcer, thyroid problems and cardiovascular disease.
The endocrine disrupting chemicals (EDCs) in plastics have been contributing to obesity and diabetes.
The plastic bottles may leach cancer – causing chemicals such as phthalates (a component makes plastic pliable) and Bis – phenol A ( a component harden plastic).
Plastic Pollutiono Plastic is one of the few new chemical
materials which pose environmental problem.
o Plastic in the environment is regarded to be more an aesthetic nuisance than a hazard, since the material is biologically quite inert.
o Plastic is cheap, it gets discarded easily, and, its persistence in the environment can do great harm.
Conversion of Plastic Waste into Liquid Fuel
Methods to convert waste plastics into hydrocarbon fuel have been in development for decades. But the associated costs to commercialize the technologies were prohibitive in previous years when crude oil was relatively inexpensive.
As costs for crude oil have risen, concerns about energy security and the environment are renewing efforts in plastics-to fuel recycling processes. Scientists hope the technologies will soon provide the nation with cheaper, alternative fuels that can help reduce foreign oil dependency.
Recycling of PlasticsPlastic recycling is the process
of recovering scrap or waste plastic and reprocessing the material into useful products, sometimes completely different in form from their original state. For instance, this could mean melting down soft drink bottles and then casting them as plastic chairs and tables. Typically a plastic is not recycled into the same type of plastic, and products made from recycled plastics are often not recyclable.
Biodegradable PlasticsBioplastics are a form of plastics derived from
renewable biomass sources, such as vegetable fats and oils , corn starch or micro biota .Common plastics, such as fossil-fuel plastics, are derived from petroleum. These plastics rely more on scarce fossil fuels and produce more greenhouse gas. Some, but not all, bioplastics are designed to biodegrade. Bioplastics which are designed to biodegrade can break down in either anaerobic or aerobic environments, depending on how they are manufactured. There is a variety of bioplastics being made; they can be composed of starches, cellulose, or other biopolymers. Some common applications of bioplastics are packaging materials, dining utensils, food packaging, and insulation.
Plasma Pyrolysis Technology (PPT)
Plasma pyrolysis or plasma gasification is a waste treatment technology that gasifies matter in an oxygen-starved environment to decompose waste material into its basic molecular structure. It uses high electrical energy and high temperature created by an electrical arc gasifies and does not combust the waste as incinerators do. This arc breaks down waste primarily into elemental gas and solid waste (slag), in a device called a plasma converter.
Prevention Strategies
REFUSE –refuse plastic carry bags at the grocer’s shop. Use
natural fibre bags.
REDUCE – Choose
products with
minimum plastic
packaging.
REUSE – Reuse non
– toxic containers and goods.
RECYCLE – Recycling is not a
sustainable solution.
- Can be a last option.
4 – R for Plastics
Share what you’ve learned Lead by example Ask your friends and family to join
you Speak to city council Write letters to government officials Get your school involved.
Conclusion Plastic Waste Management has assumed great
significance in view of the urbanisation activities.
Various strategies are being devised to mitigate the impact of plastic waste in India.
Some significant challenges still exist from both technological factors and from economic or social behaviour issues relating to the collection of recyclable wastes, and substitution for virgin material.
Some words that might motivate all of us
Mahatma Gandhi – “You must be the change if you wish to
see in the world”. Time for a new ethic :
Save yourself and you save the environment.
THANK YOUEfforts by :Ms. Bhavna AroraDisha and Niharika Parinita and Chahat 8th A
Recommended