吉影-T1水下无人机 - GENEINNO

吉影-T1水下无人机

用户手册 V1.1.02019.06

一、使用说明

安全指引 2

用户手册 2

APP下载 2

官网地址 2

二、产品介绍

包装清单 3

主要部件 3

连接主机 4

连接蓝牙手柄 5

连接充电器 5

三、APP操控

App主界面 6

App相机设置 6

APP操控界面 7

APP系统设置 8

APP照片及视频 9

照片及视频导出到电脑 9

四、故障与排除方法

常见故障 9

排除方法 9

五、附录

产品参数表 10

免责声明 11

产品保修 11

目录

© 2018-2020 吉影创新版权所有

用户手册：

本手册内容和图片均以实物以及最新版本为准，内容如有更新，恕不另行通知，请登录官网 “服

务与支持” 页面获取最新版本。APP更新较快，请参考APP内新手指引教程。

APP下载:

安卓APP下载苹果APP下载

官网地址：

http://www.geneinno.com/

安全指引：

1. 请在开阔水域、水质相对清晰的环境内使用，尽量避免在过多水生植物、过于浑浊或有非常复杂

水下结构物的环境内使用。

2. 确保无线中继器周遭无密集无线电装置或巨大金属物体，正确打开/安装天线，以免影响无线中

继器信号的正常接收。

3. 请使用官方标配充电器充电，电量告警后请及时充电，勿完全耗尽。

4. 结束使用后，请及时用淡水冲洗、擦干，降低海水腐蚀，存放于干燥通风处。

5. 主机在不安装配重块前为正浮力设计；建议淡水不安装配重块，海水可安装配重块，安装位置请

根据主机实际平衡状态调整，以主机能达到最好的平衡状态为准。

6. 无线中继器设计为低等级防水标准，请勿直接放在水中使用或直接用水冲洗。

7. 开始使用/充电前请检查所有水密接插是否有水等液体残留，请擦拭干净后再进行连接；建议先

连接无线中继器，再连接主机，系统即会上电，结束使用时只需要断开缆线和主机的连接即可。

8. 开始使用前请仔细检查电机和螺旋桨表面是否有附着物；切勿在产品工作状态下将手指或或身体

其他部位伸入推进器网罩以内；请在机器关闭状态下清理干净电机和螺旋桨表面附着物并用清水冲

洗后，再开机使用。

9. 16岁及以下青少年需在大人陪同下使用本产品；使用过程中请控制好运动速度，避免运动过快的

碰撞造成划伤或设备损坏。

10. 请勿在本产品上放置重物，勿置于阳光下暴晒，勿放置于非常潮湿/腐蚀性环境中存放。

11. 请将主机和无线中继连接好并连接APP后，按照指示进行指南针校准，并检测视频、数据传输

和操控正常后，再放入水中；应根据使用环境，在APP内设置海水，淡水，以免影响水深数据。

一、使用说明

2


二、产品介绍

吉影T1水下无人机是一款消费级智能水下无人机，搭载A17/A7双核CPU，支持H264/265

4K视频编解码，内置专业级深海星光级4k摄像头，前置3000lm led补光灯，内置专用图像处

理DSP，显著提高各种场景图形处理能力，同时整机采用工业级防水方案，最大下潜深度可

达150m，水下潜行最大速度2m/s，2个大功率水平推进器，4个小功率垂直推进器，采用闭

环控制算法，可以有效实现360度全姿态控制，水下悬停，自平衡，俯拍仰拍等,具有强大的

抗流能力应对各种复杂环境，内置大容量锂电池确保长续航能力。


④ 信号/充电接口

主要部件：

主机

① 摄像头

② 辅助光源

主机正面

主机反面

⑥ 浮力调节块

③ 推进器

③ 推进器

⑤ 排水口⑦外挂接口

无线中继器+缆线

缆线+绕线筒无线中继器

包装清单：

1主机. 2无线中继器. 3 缆线. 4 充电器. 5 配重块. 6 手柄. 7 滤镜(选配). 8 用户手册

3

使用步骤：

1. 设备连接：在岸上干燥环境下，将无线中继器缆线的一端插到无线中继器的插座上，用力拧紧，

另一端插到主机的插座上，同样用力拧紧，即已完成系统的连接，并自动上电开机。

2. APP连接：设备正常连接启动后(大概1分钟左右)，主机LED会每隔几秒钟开始闪烁，如果每次

闪烁2次，说明主机已准备好，这时可以用手机，平板，PC等设备搜索名称为GENEINNO_XXXX

的WIFI热点，连接此热点，默认密码为：88886666，手机,平板打开APP则会自动连接设备，进

入控制界面

3. 使用：将主机放入水中，即可自由操控水下无人机上浮，下潜。无线中继器具有低等级防水标

准，建议放在岸上或船上并固定好，以免主机被拉下水后回收困难。


①③

主机

无线中继器

②

④

⑤

客户端：

移动设备：安卓或IOS系统

连接主机

充电器：

① 插头

② 电源适配器

③ 充电接口

4

连接蓝牙手柄

a. 开机：把左侧开关拨动到on，按住Home键(约2秒)至LED1和LED2闪烁，手柄开机；

b. 手柄连接：手柄进入连接模式后，打开APP首页右侧菜单-蓝牙手柄，点击搜索蓝牙手柄，

可搜到手柄地址及名称(GENEINNO-XXXX)，点击连接。连接成功后手柄LED1/2会常亮；

c. 关机：把左侧开关拨动到off，手柄关机。开机之后3分钟未连接蓝牙设备，手柄自动关机；

手柄蓝牙连接后5分钟无任何操作，手柄自动关机；

d. 蓝牙手柄充电：

蓝牙手柄右遥杆往下拉，LED1/2由常亮变为熄灭时，手柄处于电量低状态需充电，充电时

LED1/2常亮，LED3/4闪烁，LED3/4常亮时，手柄充电完成


连接充电器

1. 您可以在操作界面上看到主机上的电量信息，在无线中继器上看到电量指示灯信息；低电量的

时候请及时充电，采用标配的充电器及插头，对主机进行充电，充电时间约3小时，无线中继器充

电时间约2小时，充电时充电器上的指示灯亮红色，充满后亮绿色。

2. 充电时需在岸上干燥的地方进行，请勿让充电接头接触到水。

主机

①

无线中继器

充电器

②

①主机充电：将充电器插头和主机插座连接拧紧即可

②无线中继器充电：将充电器插头和无线中继插座连接拧紧即可

X：减档 Y：加档

L：刻录L2：拍照

上浮下潜

方向操控：前进后退左转右转

A：确认 B：退出

R：减LED亮度R2：加LED亮度

5

三. App操控


App：主界面示意图

：机型

：菜单键（里面有APP升级、固件升级、蓝牙手柄、关于和帮助选项）

：机器图片

：当前设备连接状态及操控界面入口

：设备页

：论坛页面入口

：水底之城入口

：相册入口

1 2

3

4

5 6 7 8

[1]

[2]

[3]

[4]

[5]

[6]

[7]

[8]

App相机设置(在APP操控界面内)相机设置由拍照设置和刻录设置两部分组成。如图：

拍照设置分为以下三个设置项1. 单拍模式2. 连拍模式3. 直播流分辨率：直播流分辨率需重启生效

拍照设置刻录设置

刻录设置分为以下四个设置项1. 分辨率：可设置4K或者1080P2. 编码格式：可设置视频编码为H264/H264

视频保存默认为MP4格式3. 文件长度：可设置视频分段长度4. 水印开关：可设置照片和视频中水印信息开启

与关闭

6

App主界面

：返回首页

：3D姿态以及指南针

：灯开关及显示

：定深开关

：定向开关

：操控轮盘（前进/后退/左转弯/右转弯）

：自动平衡图标

：蓝牙手柄图标

：主机运行时间

：水深数据显示

：水温数据显示

：主机信号延时

：电池电量信息显示

：设置菜单入口

：拍照/刻录切换开关

：快门

：相机设置按钮

：姿态操控轮盘（上浮/下潜/抬头/低头）

：机器俯仰角度状态显示以及清零按钮

：档位开关及显示

：机械手图标及控制开关

App操控界面


App：操控界面示意图

5

6

7 8 9 10

1

2

3

4

11 12 13 14

15

16

1719

20

21

[21]

[1]

[2]

[3]

[4]

[5]

[6]

[7]

[8]

[9]

[10]

[11]

[12]

[13]

[14]

[15]

[16]

[17]

[18]

[19]

[20]

18

7

App系统设置


1. 相册：打开进入远程ROV相册和本地相册

2. 自动平衡：开启与关闭自动平衡功能

3. 指南针校正：开启指南针校正4. 环境切换：切换机器使用环境

（该项设置只对水深精度有影响）

5. 切换左右手：切换左右手操控模式

6. 单位设置：设置单位为公制或者英制

7. 电池信息：电池一些基本参数信息显示

8. 新手引导：新手引导说明

9. 固件版本：当前机器固件版本显示

10.存储情况：当前机器内部存储卡的状态显示

11.恢复出厂设置：恢复机器所有设置项为出厂设置

8


App照片：分为远程ROV目录和本地目录，长按选中照片进行保存、删除和全选。如图：

APP照片及视频

照片及视频导出到电脑1. PC端Windows (Win 10以外系统)

首先使用一台笔记本电脑连接设备WIFI，然后在开始-运行里面输入\\192.168.8.8，即可打开设备文件系统，Photos即照片存放文件夹，Videos即视频存放文件夹，打开选中便可进行复制、剪切、删除或者从电脑copy文件等操作。

Win10打开浏览器，输入网址http://192.168.8.8/media进入文件管理页面， photos存储照片，

video存储视频，打开对应文件夹，右键选中文件，选择“链接另存为”进行下载操作。

MacMac连接到无线中继器WIFI热点，然后打开Mac上的Finder应用，打开应用后按键盘上的

command+K 组合键，在服务器地址中输入smb://192.168.8.8，等待连接成功后进行操作。

2. Android移动端首先使用平板或者手机连接设备，连接成功后进入照片视频页面，选择远程ROV目录，打开并长按

选中您想下载的照片或者视频进行下载操作，您保存的文件在平板或者手机DCIM/ROV目录下。

四、故障与排除方法

1.缆线连接后无法搜索到GENEINNO WIFI热点：

• 检查缆线是否插紧接触好；

• 检查无线中继器电量指示灯，是否无线中继器电量不足。

2.连接到了GENEINNO WIFI热点，但是无法看到实时画面、无法操控：

• 检查主机是否闪灯，如闪烁3、4或5次，主机内部故障，请联系售后客服；

• 灯不闪烁，请确认是否主机电量不足了，尝试充电后再次使用；充电后还是无法使用，请联系

售后客服。

3. 马达异物卡死故障：

• 请先断电，手动清除障碍物后，再通电重新开机。

获取更多信息请打开APP帮助信息。

9

http://192.168.8.8/media

五、附录

主机

重量 4.4kg

尺寸 390×347×165 mm

最大深度 150m（淡水）

最快速度 2m/s

运动自由度前进/后退, 上浮/下潜, 左转/右转, 俯拍/仰拍

推进器数量 6

摄像

影像传感器 1/2.5 inches SONY CMOS

录像分辨率 4K

录像格式 MP4(H264/H265)

图片格式 JPEG

FOV 160°

灯光强度 1500流明×2

存储空间 32G

缆线

拉力 50KG

长度 100m/150m

直径 4.5mm

传感器

IMU 6 axis gyro & accelerometer+3 axis Compass

深度传感器 +/- 0.2m

温度传感器 +/-0.5℃

电池

化学元素 Lithium

容量10.8V/9000mAh/97.2Wh（主机）

10.8V/3200mAh/34.56Wh(无线中继器)

运行时长 4 小时（主机）/6小时（无线中继器）

充电时长 3 小时（主机）/3小时（无线中继器）

App操作

系统平台 IOS 9.0以上和 Android 5.0以上


产品参数表

10

免责声明


1. 用户任何不按照说明书指示的不当行为或强行拆卸产品的行为，或由非机器故障原因导致的产

品损坏或无法正常工作，本公司将不承担售后退换货义务，同时由此产生的维修、零件更换和运

输费用将由用户承担。

2. 请严格按照使用说明书指示使用本产品，任何违反使用说明书指示的使用行为导致用户身体的

伤害、疾病或财产等方面的损失，本公司不承担相关责任及费用。

3. 用户在本产品上自行安装或附加的不属于本公司发售的设备、第三方配件或结构，并造成产品

的损坏，本公司将不负责其售后维修及保养；同时由于附加零部件导致的产品损坏或故障，本公

司将不承担售后退换货义务，而由此产生的维修、零件更换和运输费用将由用户承担。

4. 未经官方许可，在军事管理水域、禁止进入/拍摄水域或敏感水域内使用本产品而造成的任何损

失，本公司不承担相关责任。

5. 本公司通过其他官方途径声明不涵盖的在使用本产品过程中造成的损失，同样不属于本公司的

责任范围，本公司不承担相关责任。

产品保修

1. 产品在使用中出现故障，请尽快查看说明书内故障与排除方法，或直接和我公司售后服务取得

联系、咨询，以免延误您对产品的使用和维修期限。

2. 本产品自客户购买之日起实行整机跟踪服务，保修一年，在保修期内，因设备本身不良引起

的故障，本公司负责免费修理。设备外壳划伤或撞击导致破损等用户使用造成的，以及自行拆开

维修等，将不享受免费维修。

3. 超过保修年限的，维修时收取维修费。（修理费+元器件费）

4. 售后服务请登录公司网站查看售后流程：

网址: www.geneinno.com

或通过电子邮件联系本公司售后支持：

邮箱: [email protected]

反映售后问题前，请获取贴于机器底部的产品ID号码，并提供给售后支持人员。

欢迎您对我们的产品质量和售后服务提出宝贵意见。

11


mailto:[email protected]

深圳市吉影科技有限公司www.geneinno.com

官方媒体

Facebook YouTube

微信微博

Geneinno T1

USER MANUAL V1.1.0

2019.06

I. Users tips

Safety Instructions 2

Manual 2

APP Download 2

II. Product

Packing list 3

Main parts 3

Connect the system 4

Connect Bluetooth controller 5

Charge 5

III. APP operation

App main interface 6

App camera settings 6

App operation interface 7

APP system settings 8

App photos and videos 9

Export photos and videos to computer 9

IV. Brief Troubleshooting 9

V. Appendixes

Product parameter list 10

Disclaimer 11

Product warranty 11

CONTENT

Copyright © 2018-2020 GENEINNO All Rights Reserved.

User Manual：

The contents and pictures of this manual are subject to the actual version and the

latest version. The content is subject to change without prior notice. Please visit the

official website “Download” page for the latest version. The APP updates frequently,

please refer to the tutorial for beginners in the APP

APP Download:

Android IOS

Safety Instructions：

1. Please use in the open water with clear water quality. Try to avoid using in the

environment with too many aquatic plants, too cloudy or very complex underwater

structures.

2. Ensure that there are no high-power radio devices or large metal objects around the

wireless relay. Open/install the antenna correctly to avoid affecting the normal reception of

wireless signals.

3. Please use the official standard charger to charge the battery. When there is low-battery

warning, please charge it in time, and do not run out battery.

4. After use, please rinse in fresh water and dry in time, to reduce seawater corrosion. Store

in a dry and ventilated place.

5. The drone is designed with positive buoyance. It is recommended not to install the

balancing weight in fresh water, but to install it in seawater. The installation position should

be adjusted according to the actual balance state of the drone, whichever is the best

balance that the drone can achieve.

6. Wireless relay is designed for low grade waterproofing standards, do not use it directly in

water.

7. Please check if any residual liquid such as water in all water-proof connectors. Please

clean them before connection/charging. It is recommended to connecte to the wireless

relay first, and then to the drone. The system will be powered on after connection, and will

be powered off when not connected.

8. Please carefully check if any debris on the surface of motor and propeller before use; Do

not put fingers or other body parts into the propeller when the drone is on. Please clean

the debris on the surface of motor and propeller when powered off and rinse it with water

before start.

9. Teenagers aged 16 and under should be accompanied by adults to use this product;

Please control the speed of movement during use to avoid scratches or equipment damage.

10. Do not place heavy objects on this product. Do not expose it directly under the sun, or

store it in very humid/corrosive place.

11. For operation, please connect the drone and wireless relay and connect to APP first, run

compass calibration, and check video/data transmission and control status before putting

the drone into the water. Seawater and fresh water should be set in the APP according to

the operating environment to avoid inaccuracy of depth data.

I. User tips

Copyright © 2018-2020 GENEINNO All Rights Reserved. 2

II. Product

Overview：

Geneinno T1 is a consumer level underwater intelligent drone, equipped with A17/A7

dual-core CPU, supporting H264/265 format, 4K video encoding and decoding.

Equipped with professional deep-sea starlight level 4k camera, front 3000lm led light,

and built-in special image processing DSP,

At the same time, the whole machine adopts industrial-grade waterproof scheme,

with a maximum diving depth of 150m.The maximum speed is 2m/s, 2 high-power

horizontal thrusters and 4 low-power vertical thrusters. The closed-loop control

algorithm can effectively realize 360 degree full-attitude control, underwater

hovering and self-balance.

④signal/charging port

Main parts:

Head

① Camera

② Light

Top

Bottom

⑥ Buoyancy control block

③Thruster

③ Thruster

⑤Drainage port

⑦ Extension port

Wireless relay:

Cable & Winder Wireless relay


Packing list：

1. Geneinno T1 Drone, wireless relay, cable & winder; 2. Charger; 3. Balancing weight; 4.

The bluetooth handle; 5. Filter (user’s choice); 6. User Manual

Drone:

3

Usage:

1. Connect device: Insert one end of the wireless relay cable into the socket of the wireless

relay and tighten it with force. Insert the other end into the socket of the drone and

tighten it with equal force, then complete the connection and power on.

2. App connect: when the drone gets to work (about 1 minute after connection), the LED

light on, the drone will flash twice every several seconds, it means the machine is ready to

connect to your phone, pad and PC devices, search the Wi-Fi hotspot named

GENEINNO_XXXX, connect your device to it, the default passwords is 88886666, then get

to the app control interface.

3. Operation: Put Geneinno T1 into the water, you can freely control it to rise and dive.

Wireless relay has low grade waterproofing standard. It is recommended to be placed on

shore or on board and fixed to avoid the difficulty of recovery after being dragged into the

water by the drone.

Android and IOS

Connect the system

Charger

① Plug

② Adapter

③ Charging port

①③

Drone

wireless relay

②

④

⑤


Connect Bluetooth controller

1. Connecting：

A: Start up: push the left switch to on, press the Home button (about 2 seconds) to LED1 and

LED2 to blink, and start the handle.

B: Handle connection: after starting up, the working lamp flashes and the handle enters the

connection mode. Open the right menu of APP homepage - bluetooth handle,

Click to search the bluetooth handle, and you will find the handle address and name (geneinno-

xxxx). Click to connect. Led1/2 handle will always be on after successful connection.

C. Power off: push the left switch to off and turn off the handle. 3 minutes after starting up,

the bluetooth device is not connected, and the handle is off automatically. There is no operation

for 5 minutes after the bluetooth connection of the handle, and the handle is off automatically

D. Bluetooth handle connection status confirmation:

After successful connection of bluetooth handle, open GeneROV APP and enter the full-screen

control interface of APP. The handle icon will appear in the status bar at the top of APP

Charge

1. The machine battery info will be seen at APP operation interface, battery signal light info will

be seen at wireless relay; Please charge the drone when battery is low using standard charger

and plug; charge the drone for 3 hours, wireless relay for 2 hours; signal lights on charger is red

when it’s charging, turn into green when fully charged.

2. Be sure, that there are no water in the plugs,before you start charging.

①

Drone

Charger

②Wireless relay

Charge① How to charge the machine: tighten the plug between charger and the drone

②How to charge wireless relay: tighten the plug between charger and wireless relay

X：increase gearY：reduce gear

L：Record L2：Shot

Dive up/downDirection controlStick:

up/down left/right

A：ConfirmB：Quit

R：reduce LED lightnessR2：increase LED lightness


III. APP operation

APP main interface

：Product type

：Menu (APP update, hardware update, Bluetooth controller, about and help options)

：Product picture

：Current connection status and entrance of operation interface

：Device

：Forum

：Underwater City

：Album

1 2

3

4

5 6 7 8[1]

[2]

[3]

[4]

[5]

[6]

[7]

[8]

App camera settings (in APP operation interface)

Camera settings are composed of photo settings and recording settings, as shown below：

Photo settings are composed of three parts:1. Single-shot mode2. Burst-shot mode3. Live stream resolution: activate after reboot

Photo settings Recording settings

Recording settings are composed of four parts:1. Resolution：4K / 1080P2. Video Format：H265/H264,

Video will be saved as MP43. File time length: range from 0-30min,

unsegmented division when time length is 04. Watermark switchers: add depth, temperature,

time and other info on photo/video


：Return to main interface

：3D real-time posture and attitude

：LED switch and lumen adjust

：Depth lock

：Direction lock

：Motion control wheel（Forward/Backward/Left/Right）

：Auto balance

：Bluetooth controller

：Running time

：Depth

：Water temperature

：Live-stream delay

：Battery

：System settings

：Shot/Record switch

：Shot/Record

：Camera settings

：Attitude control wheel（Up/Down/Tilt up/Tilt down）

：Tilt status & angle

：Speed gear

：Underwater gripper

APP operation interface

APP Operation Interface

5

6

7 8 9 10

1

2

3

4

11 12 13 14

15

16

1719

20

21

[21]

[1]

[2]

[3]

[4]

[5]

[6]

[7]

[8]

[9]

[10]

[11]

[12]

[13]

[14]

[15]

[16]

[17]

[18]

[19]

[20]

18


APP system settings


1. Album ： enter the remotealbum and local album

2. Auto balance ： turn on/offauto balance

3. Compass calibration ： startcompass calibration

4. Environment setting ： theoption for fresh/salt water,select salt water or fresh water,which has effect on depthaccuracy only

5. Left/right hand switch ：change left/right hand mode

6. Unit setting：set unit to theMetric/British System

7. Battery info ： display ofbattery information

8. User guide ：APP user guide

for starters

9. Firmware version ： firmwareversion display

10.Storage ： display of storagestatus in the machine

11.Restore to factory setting ：restore machine to factorysetting

8

App photos: divide into remote ROV directory and local directory, save, delete andselect all the selected photos by long press

App photos and videos

Export photos and videos to the computer1. PCWindows(Win 10 excluded):

First, use a laptop to connect to the device WIFI, and then enter \\192.168.8.8 in thestart-run to open the device file system, Photos is the photo storage folder, Videos is thevideo storage folder, and when opened, you can copy, cut, delete or copy files from thecomputer.Win10

First, use a laptop to connect to the device WIFI, then open a browser, enterhttp://192.168.8.8/media to enter the device file system. Photos are in the photo storagefolder, Videos are in the video storage folder. Right click on the file and click ‘Saveas’to download the selected files.Mac

The Mac connects to Geneinno T1 WIFI, and then open the Finder application on theMac. After opening the application, press the command+K key on the keyboard and enterSMB:// 192.168.8.8 in the server address, then enter the storage folders to download files.

2. AndroidFirst, use the tablet or mobile phone to connect the device. After successful connection,

enter the photo video page, select the remote ROV directory, open and select the photo

or video you want to open for download.

IV. Brief Troubleshooting1. Cannot search for GENEINNO WIFI hotspot after cable connection:

• Check if the cable is connection is tight.

• Check the buoy battery indicator, if the buoy battery is low.

2. Connected to the GENEINNO WIFI hotspot, but can't see the real-time video stream,

and can't control:

• Check if Geneinno T1 LED flashes, such as flashing 3, 4 or 5 times, indicating the

internal malfunction of the machine, please contact after-sales customer service.

• When LED light does not flash, please confirm if the battery is low or not, try to use it

again after charging; if it still could not be used after charging, please contact after-sales

customer service.

3. Motor obstruction

• Please power off first, manually remove the obstacles, and then turn on the power

again. For more information, please open the APP for help information.


http://192.168.8.8/media

V. Appendix

Drone

Weight 9.7Ibs (4.4kg)

Dimension 15.35×13.66×6.5 inch

390×347×165 mm

Depth 492.15ft (150m)

Speed 6.6ft/s (2m/s)

Degrees of Freedom Forward/back, rise/fall, turn left/right

Thruster 6

Camera

Image Sensor 1/2.5 inches SONY CMOS

Video Resolution 4K

Video Format MP4(H264/H265)

Photo Fomat JPEG

FOV 160°

Lumen 1500lm×2

Micro SD 32G

Tether

Strength 500N(50KG)

Length 164ft/328.08ft/492ft (50m/100m/150m)

Diameter 4.5mm/0.18 inch

Sensors

IMU 6 axis gyro & accelerometer+3 axis Compass

Depth Sensor +/- 0.2m

Temp. Sensor +/-0.5℃

Battery

Chemical Lithium

Capacity10.8V/9000mAh/97.2Wh (drone)

10.8V/3200mAh/34.56Wh (wireless relay)

Run time 4 hours(drone)/6 hours(wireless relay)

Charge time 3 hours(drone)/3 hours(wireless relay)

App

Platform IOS 9.0 and Android 5.0

Product parameter list


Product warranty

1. If the product fails during operation, please go through the trouble shooting of the

user manual, or contact and consult with our service team as soon as possible to avoid

delay in your use and maintenance period.

2. This product is subject to the whole machine tracking service from the date of

purchase by the customer. The warranty is one year. During the warranty period, the

company is responsible for free repair due to the failure caused by the equipment itself.

If the equipment is scratched or impacted, resulting in damage, which is caused by the

user, or self-disassemble and etc., will not enjoy free maintenance by the company.

3. If the warranty period is exceeded, the maintenance fee will be charged for the repair

to the customer. (repair cost + component fee)

4. For after-sales service, please visit our official website for online instructions:

Website: www.geneinno.com

or you could email us directly to our after-sale support:

Email: [email protected]

Please get the product ID number attached on the bottom of the drone and provide it

to the after-sales support staff before your after-sales service. You are most welcome to

give us valuable advice on our product quality and after-sale service.


Disclaimer

1. The company shall not be liable for the after-sale return and replacement of the

product for any damage or failure caused by forced disassembly or non-machine

operational malfunction, and the maintenance, parts replacement and transportation

expenses incurred will be borne by the user.

2. Please use this product strictly following the instructions of the user manual. Any

violations of the instructions result in injury, disease or property loss of the user, will

not be borne by the company.

3. The company will not be responsible for after-sales maintenance of the non-standard

equipment, third-party parts or structures installed or attached by users on the

products which are not sold by the company. The company will not assume the

obligation of product return or replacement after sales due to damage or failure of

additional parts, and the maintenance, parts replacement and transportation expenses

incurred will be borne by the user.

4. Without official permission, the company shall not be liable for any loss caused by

the use of this product in waters under military administration, waters prohibited from

entering/photographing or sensitive waters.

5. Other losses that are not covered by the company, which stated officially, will not be

borne by the company.

11


mailto:[email protected]

Shenzhen Geneinno Technology Companywww.geneinno.com

Official Media

Facebook YouTube

Wechat Weibo

Documents

吉影-T1水下无人机 - GENEINNO