Upload
happystargr
View
213
Download
0
Embed Size (px)
DESCRIPTION
01. ETE-M Spec
Citation preview
_________________________________________________________________
System
Tactical Exchange
ETE-M
Technical Description
December, 2015
Rev. 1.0
Function
Organization
Name
Phone No.
Signature
Date
Prepared by
Peryphon
Electrical Design
Peryphon
and Engineering
Mechanical Design
Peryphon
and Engineering
Engineering &
Development &
Peryphon
Project Manager
Check, Approved
Peryphon
23 Hamelacha St., entrance B, floor 2, New Industrial Park Rosh-Ha’ayin 48091 Israel Page 1 of 12
TEL: +972-3-9025682 +972-3-9025684 FAX:
www.peryphon-dev.co m X
File name - ETE-M Spec.docx
_________________________________________________________________
Copyright Peryphon Dev Ltd
Proprietary Notice
This document contains classified and confidential information and is owned by Peryphon Dev. It is prohibited to copy, use, or transmit this document and/or any part thereof to any unauthorized persons without the written permission of Peryphon Dev Ltd
Revision History Table
Revision
Date Issued
Description of Change
Source of
Change
1
2
3
4
23 Hamelacha St., entrance B, floor 2, New Industrial Park Rosh-Ha’ayin 48091 Israel Page 2 of 12
TEL: +972-3-9025682 +972-3-9025684 FAX:
www.peryphon-dev.co m X
_________________________________________________________________
TABLE OF CONTENTS
Para. Title of Para. Page
1. ETE-M 5X
1.1 PRODUCT DESCRIPTION 5X
1.2 ELECTRICAL SPECIFICATIONS 7X
1.3 MAIN FEATURES 7X
1.4 CONFIGURATION, SETUP AND TESTING 8X
1.5 CONNECTORS AND INDICATIONS 8X
1.6 MIL-STD COMPLIANT 9X
1.7 PHYSICAL CHARACTERISTICS AND ENVIRONMENTAL CONDITIONS 10X
1.8 INSTALLATION AND CARRY 10X
1.9 LINE DISTRIBUTION FRAME – LDF12 11X
LIST OF FIGURES
Figure Title of Figure Page
Figure 1. ETE-M (for reference only) 5X
Figure 2. ETE-M Connectivity example 6X
23 Hamelacha St., entrance B, floor 2, New Industrial Park Rosh-Ha’ayin 48091 Israel Page 3 of 12
TEL: +972-3-9025682 +972-3-9025684 FAX:
www.peryphon-dev.co m X
_________________________________________________________________
LIST OF ABBREVIATIONS
Abbreviation
Clarification
FXS
Foreign Exchange subscriber
FXO
Foreign Exchange Office
LAN
Local Area Network
WAN
Wide Area Network
23 Hamelacha St., entrance B, floor 2, New Industrial Park Rosh-Ha’ayin 48091 Israel Page 4 of 12
TEL: +972-3-9025682 +972-3-9025684 FAX:
www.peryphon-dev.co m X
_________________________________________________________________
ETE-M
Figure 1. ETE-M (for reference only)
PRODUCT DESCRIPTION
The ETE-M is a compact, heavy duty, military grade PBX that supports 140 extensions total, including 36 FXS subscribers, 4 FXO lines and up to 100 IP phones using external switches. This rugged and waterproof product operates on a 10.8-33VDC power source.
ETE-M subscribers include CB telephones and IP phones. CB telephones are connected via field wire, using standard binding posts on the unit's front panel for fast and secure connection.
The subscribers can make calls from one extension to the other by dialing the required extension number. The product also provides telephony features such as Call Transfer, Call forward, call waiting, three way conferences and hunt groups.
The 1st 12 FXS interface are accessible via binding post pairs on the front panel. The other 24 FXS interfaces are accessible via two line distribution frames (LDF-12) that connect to the ETE-M via two connectors on the ETE front panel.
The ETE-M has four FXO lines (also accessible via binding post pairs on the front panel) which allow connection to a subscriber line of another telephony exchange (e.g. a PSTN line drop or any other military PBX). The following figure shows a typical deployment:
23 Hamelacha St., entrance B, floor 2, New Industrial Park Rosh-Ha’ayin 48091 Israel Page 5 of 12
TEL: +972-3-9025682 +972-3-9025684 FAX:
www.peryphon-dev.co m X
_________________________________________________________________
Figure 2. ETE-M Connectivity example
As the ETE-M includes a state of the art VoIP telephony exchange, it also supports up to 5 IP phones that can be connected directly to its local LAN interfaces, or up to 100 IP
Phones via an external IP switch, in addition to the 36 FXS extension and 4 FXO extensions.
The ETE-M can also be connected to a higher and lower echelon PBX via one of its LAN/WAN interfaces, using modern VoIP protocols (SIP/RTP).
23 Hamelacha St., entrance B, floor 2, New Industrial Park Rosh-Ha’ayin 48091 Israel Page 6 of 12
TEL: +972-3-9025682 +972-3-9025684 FAX:
www.peryphon-dev.co m X
_________________________________________________________________
ELECTRICAL SPECIFICATIONS
Power
Power feed 10.8-33VDC (Approx. 80W±20% maximum when all lines are active simultaneously at nominal input voltage of 24VDC)
Subscriber interfaces
36 FXS lines (CB telephone extensions with loop current of 25mA which can support up to 10Km communication link using ETP-1 telephone connected with WD-TT1 tactical wire. It is possible to connect 2 additional ETP-1 phones on the end-side. The cable used to connect each of the additional 2 phones shall be less than 100m in length.
The FXS line can support up to 20Km communication link using one ETP-1 telephone connected with WD-TT1 tactical wire.
It is important to note that while the solution supports 10/20Km enabling the user to establish calls and conversation (with ability to clearly understand the words on both sides of the line), there may be reduced performance over long distances, as a result of the attenuation of the cable (the longer the cable, the more attenuation that is introduced onto the communication line)
4 FXO lines (Foreign Exchange Office)
LAN/WAN interfaces
5 Fast Ethernet (10/100Base-T) LAN ports
1 Fast Ethernet (10/100Base-T) WAN port
Serial console interfaces, including ability to reinitialize the board in case of software malfunction.
MAIN FEATURES
Subscriber to subscriber calls
Hot line / Automatic dialing
Call hold / retrieve
Consultation
Call Transfer
Call forward
Call waiting
Up to 10 simultaneous on-board 3way-conferences initiated by FXS subscribers.
Hunt groups
Flexible dialing plans
23 Hamelacha St., entrance B, floor 2, New Industrial Park Rosh-Ha’ayin 48091 Israel Page 7 of 12
TEL: +972-3-9025682 +972-3-9025684 FAX:
www.peryphon-dev.co m X
_________________________________________________________________
CONFIGURATION, SETUP AND TESTING
Web based configuration for all telephony related features
CLI and SNMP Ver. 2 and Ver. 3
Configuration files
A rich set of build-in testing capabilities
CONNECTORS AND INDICATIONS
Front Panel
The front panel includes the following elements:
Power On/Off toggle Switch
DC Power-in connector
DC Power status indication LED:
Solid on Green: external power source is active.
3 Audiocodes boards Status indication LEDs (Green):
Solid on: board is active and ready
Flashing: board at initialization.
Off: board not active
12 Binding posts pairs for FXS subscribers
4 Binding posts pairs for FXO lines
2 Connectors towards external line distribution frames, 12 (FXS) lines each
LAN1 connector, including:
LAN1 of Board-1 (4 wires)
WAN of Board-1 (4 wires)
Serial console of Board-1 (3 wires, TX, RX, GND)
LAN2 connector, including:
LAN1 of Board-2 (4 wires)
LAN2 of Board-2 (4 wires)
Serial console of Board-2 (3 wires, TX, RX, GND)
LAN3 connector, including:
LAN2 of Board-1 (4 wires)
LAN3 of Board-1 (4 wires)
Serial console of Board-3 (3 wires, TX, RX, GND)
Ground Screw
23 Hamelacha St., entrance B, floor 2, New Industrial Park Rosh-Ha’ayin 48091 Israel Page 8 of 12
TEL: +972-3-9025682 +972-3-9025684 FAX:
www.peryphon-dev.co m X
_________________________________________________________________
Rear Panels
Sealing screw / pressure equalizing nozzle (Breather)
MIL-STD COMPLIANT
Power supply according to Mil-STD-1275B
Temperature:
– High temperature / storage: MIL-STD-810F, Method 501.4 Procedure I, 71°C
– High temperature / operation: MIL-STD-810F, Method 501.4 Procedure II, 55°C
– Low temperature / storage: MIL-STD-810F, Method 502.4 Procedure I, -30°C
– Low temperature / operation: MIL-STD-810F, Method 502.4 Procedure II, -15°C
Vibration:
– Wheeled vehicle: MIL-STD 810F, Method 514.5 Procedure I, figure 514.5C-3.
– Tracked vehicle: MIL-STD 810E, Method 514.4, Procedure I, category 8, Table 514.4-AIII.
Transit drop: MIL-STD 810F, Method 516.5 Procedure IV, H=122Cm, 6 drops in transportation case on ground
Bench Handling: MIL-STD-810F, Method 516.5, Procedure VI
Functional shock: MIL-STD-810F, Method 516.5, Procedure I, 11mSec. 20g
Bounce (Loose Cargo): MIL-STD-810F, Method 514.5, Procedure II
Humidity: MIL-STD-810F, Method 507.4, 30°C to +60°C up to 95%RH,
Salt Fog: MIL-STD-810F, Method 509.4
Altitude: MIL-STD-810F, Method 500.4, Procedure I Non-operating 40,000 feet and Procedure II operating 15,000 feet
Sand & Dust: MIL-STD-810F, Method 510.4, Procedure I (Blowing Dust)
Fungus: MIL-STD-810F, Method 508.5
Rain: MIL-STD-810F, Method 506.4, Procedure I - Rain and Blowing Rain
Solar Radiation: MIL-STD-810F, Method 505.4, Procedure I
Lightning protection: per IEC 61000-4-5
23 Hamelacha St., entrance B, floor 2, New Industrial Park Rosh-Ha’ayin 48091 Israel Page 9 of 12
TEL: +972-3-9025682 +972-3-9025684 FAX:
www.peryphon-dev.co m X
_________________________________________________________________
EMI/RFI: MIL-STD 461F:
– Bonding - 2.5mΩ
– CE102 - Conducted Emission, Power Leads 10KHz-10MHz
– CS101 - Conducted Susceptibility, Power Leads 30Hz-150KHz
– CS114 - Conducted Susceptibility, Bulk Cable Injection, 10 KHz - 200 MHz
– CS115 - Conducted Susceptibility, Bulk Cable Injection, Impulse Excitation
– CS116 - Conducted Susceptibility, Damped Sinusoidal Transients, Cables and Power Leads, 10 KHz-100 MHz
– RE102 - Radiated Emission, Electric Field; Army ground; Figure RE102-4 - 2 MHz-18 GHz
– RS103 - Radiated Susceptibility, Electric Field, 2 MHz-18 GHz 20V/m
MIL-STD-1275B:
– Steady state voltage – 23-33VDC
– Voltage surge – 100V
– Voltage spike imported into device – spike 250V
PHYSICAL CHARACTERISTICS AND ENVIRONMENTAL CONDITIONS
Weight: less than 13.7 Kg
Width: 420 mm (not including 19" brackets)
Height: 180 mm (including bottom spacers)
Depth: 384 mm (including Binding Posts and front handles)
Color & Paint Definitions:
OLIVE DRAB EPOXY PAINTING
PAINT P513.1 PER MIL-F-14072D(ER)
FINAL PAINT FILM PER MIL-C-22750F
CHIP COLOR #24084 PER FED-STD-595B (Dark Green)
DRY FILM THICKNESS TO BE 25-40 Micron
Operation temp.: -15 ºC to +55 ºC.
Storage temp: -30 ºC to +71 ºC.
INSTALLATION AND CARRY
Two spring based recessed handles for two man carry
No special installation is needed.
Table top, or installation in a 19" rack in a 5U space, using a pair of brackets
23 Hamelacha St., entrance B, floor 2, New Industrial Park Rosh-Ha’ayin 48091 Israel
TEL: +972-3-9025682 +972-3-9025684 FAX: www.peryphon-dev.co m X
Page 10 of 12
_________________________________________________________________
LINE DISTRIBUTION FRAME – LDF12
Introduction
The Line Distribution Frame (seen on Figure 1) is a heavy duty; military grade unit connected to ETE-M, up to 2 boxes can be connected to each ETE-M, to supports additional subscribers, twelve subscribers per each box.
The subscribers are connected using standard binding posts located on the unit's top panel, for fast and secure connection.
Physical Characteristics and Environmental Conditions
Weight: Less than 2.2 Kg
Width: 167 mm
Height: 55 mm (not including binding posts)
Depth: 224 mm (not including connector and GND screw)
Color & Paint Definitions:
OLIVE DRAB EPOXY PAINTING
PAINT P513.1 PER MIL-F-14072D(ER)
FINAL PAINT FILM PER MIL-C-22750F
CHIP COLOR #24084 PER FED-STD-595B (Dark Green)
DRY FILM THICKNESS TO BE 25-40 Micron
Operation temp.: -15 ºC to +55 ºC.
Storage temp.: -30 ºC to +71 ºC.
MIL-STD Compliant
Temperature:
– High temperature / storage: MIL-STD-810F, Method 501.4 Procedure I, 71°C
– High temperature / operation: MIL-STD-810F, Method 501.4 Procedure II, 55°C
– Low temperature / storage: MIL-STD-810F, Method 502.4 Procedure I, -30°C
– Low temperature / operation: MIL-STD-810F, Method 502.4 Procedure II, -15°C
Vibration:
– Wheeled vehicle: MIL-STD 810F, Method 514.5 Procedure I, figure 514.5C-3
– Tracked vehicle: MIL-STD 810E, Method 514.4, Procedure I, category 8, Table 514.4-AIII
Transit drop: MIL-STD 810F, Method 516.5 Procedure IV, H=122Cm, 6 drops in transportation case on ground
Bench Handling: MIL-STD-810F, Method 516.5, Procedure VI
Functional shock: MIL-STD-810F, Method 516.5, Procedure I, 11mSec. 20g
23 Hamelacha St., entrance B, floor 2, New Industrial Park Rosh-Ha’ayin 48091 Israel
TEL: +972-3-9025682 +972-3-9025684 FAX: www.peryphon-dev.co m X
Page 11 of 12
_________________________________________________________________
Bounce (Loose Cargo): MIL-STD-810F, Method 514.5, Procedure II
Humidity: MIL-STD-810F, Method 507.4, 30°C to +60°C up to 95%RH
Salt Fog: MIL-STD-810F, Method 509.4
Altitude: MIL-STD-810F, Method 500.4, Procedure I Non-operating 40,000 feet and Procedure II operating 15,000 feet for 1 hour
Sand & Dust: MIL-STD-810F, Method 510.4, Procedure I (Blowing Dust)
Fungus: MIL-STD-810F, Method 508.5
Immersion: MIL-STD-810F, Method 512.4, Procedure I
Solar Radiation: MIL-STD-810F, Method 505.4, Procedure I
Installation
The Line Distribution Frame can be installed on a surface using 6 screws
23 Hamelacha St., entrance B, floor 2, New Industrial Park Rosh-Ha’ayin 48091 Israel
TEL: +972-3-9025682 +972-3-9025684 FAX: www.peryphon-
dev.co m X
Page 12 of 12