4
© 2007 American Honda Motor Co., Inc. - All Rights Reserved. AII 36617 (0705) 1 of 4 08L02-SJC-1000-91 INSTALLATION INSTRUCTIONS Accessory Application Publications No. Issue Date MAY 2007 2008 RIDGELINE ROOF RACK P/N 08L02-SJC-100 AII 36617 PARTS LIST Right side rail Left side rail 2 Cross bars Right front cover Left front cover TOOLS REQUIRED T-30 Torx bit T-25 Torx bit Hacksaw Tape measure Trim removal tool Long nose plier KTC Trim tool set T/N SOJATP2014 Right center cover NOTE: Wipe off the roof moldings before installing the roof rack. Be extremely careful not to damage the body paint. Illustration of the Roof Rack Installed on the Vehicle INSTALLATION Customer Information: The information in this installation instruction is intended for use only by skilled technicians who have the proper tools, equipment, and training to correctly and safety add equipment to your vehicle. These procedures should not be attempted by “do-it-yourselfers”. Left center cover Right rear cover Left rear cover 12 Torx nuts 8 Torx self-tapping screws Owner’s manual (not in kit)

2008 Ridgeline RoofRack AII36617

  • Upload
    v8lover

  • View
    294

  • Download
    0

Embed Size (px)

DESCRIPTION

How to install a Roof Rack on a 2008 Honda Ridgeline.

Citation preview

Page 1: 2008 Ridgeline RoofRack AII36617

© 2007 American Honda Motor Co., Inc. - All Rights Reserved. AII 36617 (0705) 1 of 408L02-SJC-1000-91

INSTALLATIONINSTRUCTIONS

Accessory Application Publications No.

Issue Date

MAY 2007

2008 RIDGELINEROOF RACKP/N 08L02-SJC-100

AII 36617

PARTS LIST

Right side rail

Left side rail

2 Cross bars

Right front cover

Left front cover

TOOLS REQUIREDT-30 Torx bitT-25 Torx bitHacksawTape measureTrim removal toolLong nose plierKTC Trim tool set

T/N SOJATP2014

Right center cover

NOTE:

• Wipe off the roof moldings before installing the roofrack.

• Be extremely careful not to damage the bodypaint.

Illustration of the Roof Rack Installed on theVehicle

INSTALLATION

Customer Information: The information in thisinstallation instruction is intended for use only byskilled technicians who have the proper tools,equipment, and training to correctly and safety addequipment to your vehicle. These proceduresshould not be attempted by “do-it-yourselfers”.

4514021K

Left center cover

Right rear cover

Left rear cover

12 Torx nuts

8 Torx self-tapping screws

Owner’s manual (not in kit)

Page 2: 2008 Ridgeline RoofRack AII36617

2 of 4 AII 36617 (0705) © 2007 American Honda Motor Co., Inc. - All Rights Reserved.

Cutting the roof molding

1. Using the appropriate trim tool, pry up on the frontof each roof molding.

2. Slide up the end of the roof molding and removethe roof molding.

3. Remove the six clips from the roof channels.

4. Using a hacksaw, cut each roof molding accordingto the dimensions shown.

4513313K

2 ROOFMOLDINGS

END OF THEROOF MOLDING

Slide up.

FRONT

4513331K

FRONT

ROOFMOLDING

230 mm

60 mm(Discard.)

425 mm

90 mm(Discard.)

555 mm

Approx.165 mm(Discard.)

HACKSAW FRONT

4513324K

FRONT

6 CLIPS

LONGNOSEPLIER

REAR CENTER FRONT

4513303K

2 ROOF MOLDINGS

FRONT

KTC TRIM TOOL

Page 3: 2008 Ridgeline RoofRack AII36617

© 2007 American Honda Motor Co., Inc. - All Rights Reserved. AII 36617 (0705) 3 of 4

5. Reinstall the clip in the front molding piece, theninstall it on the rear stud in the front of thechannel.

8. Place the roof rack assembly onto the vehicleroof. Align the roof rack holes with the studs in thevehicle roof. Take care not to damage the bodypaint. Install the roof rack assembly with twelvetorx nuts (T-30).Torque the nuts in the order shown to 10 N·m(7 lb-ft).

4513351K

1112

1

4

5

8

6

7

3

29

10

FRONT

12 STUDS

12 TORXNUTS

9. Install the six roof rack covers.

10. Loosen the cross bar holder screws. Align themarks ( ) on the cross bar holder with the marks( ) on the side rails by moving the cross bars.Tighten the cross bar holder screws.

4014502K

FRONTMOLDINGPIECE

CLIP

REARSTUD

FRONT

To leftchannel

To right channel

4513343K

FRONT

RIGHTSIDERAIL

LEFTSIDERAIL

8 TORXSELF-TAPPINGSCREWS

CROSS BAR

2 CROSS BARS

NARROWEND

FRONT

6. Reinstall all the molding you retained in step 4 inthe roof channels.

Assembling the Roof Rack

7. Install the two cross bars to the cross bar holdersof the left and right side rails with the eight torxself-tapping screws (T-25). Note the direction ofthe cross bar for installation. Turn the narrow endof the cross bar toward the rear.

4514011K

CROSS BARHOLDERSCREW

CROSS BARHOLDER

LEFTFRONTCOVER

SIDE RAIL

CROSS BAR MARKS

LEFTCENTERCOVERLEFT

REARCOVER

RIGHTFRONTCOVER

RIGHTCENTERCOVER

RIGHTREARCOVER

Page 4: 2008 Ridgeline RoofRack AII36617

4 of 4 AII 36617 (0705) © 2007 American Honda Motor Co., Inc. - All Rights Reserved.

11. To reduce wind noise, cut the rubber molding fromeach roof rack and install the pieces of the rubbermolding you just cut between the crossbars.

USE AND CARE

• Check the roof rack cross bar mounting nutsfrequently, and retighten them if necessary.

• Distribute the weight of the cargo evenly, and donot exceed the maximum weight capacity of110 lbs (50 kg).