60l Manual Actualizado

8/18/2019 60l Manual Actualizado

1/115

Model 60L Seamer Illustration, Parts and Instruction Manual

Fourth Edition

Rev: Aug. 2006 Serial No.


2/115


3/115

PNEUMATIC SCALE ANGELUS

IMPORTANT NOTICE TO OUR CUSTOMERS

PARTS LIST - PARTS ORDERING INFORMATIONTo prevent any possible error of ordering an incorrect machine part, it is advisable

that the customer always check the part number of the part to be replaced before placing

a purchase order. On occasion, original machine parts are modified utilizing an existingpart. In this case these parts would be interchangeable. However, in some instancesdesign changes have occurred in which the machine parts requiring replacement are nolonger manufactured and in this situation the customer will be notified as to the correctpart to order.

The equipment list, change parts or attachments included with this manual areidentical to those that were furnished with the original machine according to the serialnumber. This manual has been modified to express the correct components assembledon the machine at the time of shipment. Periodically, parts lists and illustrationsthroughout the manual have been stamped “Not Applicable” and should be understoodthat these components or assemblies were not supplied with the original machine and

should be disregarded. Any changes that may have been made by the customer to the machine or to the can

size change parts would not be covered in this manual the customer must check the partnumber or check with Pneumatic Scale Angelus to obtain the correct part.

SAFETY DEVICES, GENERALYour Seamer is equipped with a variety of safety devices to protect the machine and

machine operator.Depending on the model of your machine, these safety devices may include a Filler

Drive Seamer Safety Clutch. The principal purpose of the Seamer Safety Clutch preventdamage to the Seamer in an emergency or jam situation. The Filler Drive/Seamer

Safety Clutch is not designed to protect a filler or other Seamer driven equipmentagainst damage due to emergency or jam stoppage.

SEAMER SPEEDS AND PROTECTION All Seamers are designed to seam cans at a recommended maximum speed.

Seamer speeds may vary according to product, filler, ends or can characteristics.Recommended maximum Seamer speeds are calculated during the design of theSeamer. Calculations for a maximum production speed include “Under Load” situations.Many components in the Seamer are designed knowing they will be under a load whilerunning cans at high speed. The machine should only be run at maximum speeds whenthere is a sufficient can supply.

Recommendations:Running any Seamer without cans, at high speeds, will cause extensive damage or

abnormal wear and decrease the life of the Seamer. Seamers equipped with Two SpeedMotors or AC Inverters should be Programmed to slow the Seamer to half speed in theabsence of cans. A can line sensor supplied by the customer could then automaticallyincrease the Seamer to normal high speed operation after the normal supply of cans has


4/115


been reached or the supply is enough to maintain a fast mode of operation. Therefore, itis strongly recommended that the customer’s interface include these parameters toprolong life of the Seamer.

WARRANTY:a. Seller warrants that the goods manufactured by it are free from defects of material

and workmanship and are merchantable within the meaning of the CaliforniaUniform Commercial Code.

b. Seller warrants this equipment to be suitable for the purpose required and describedas expressly set forth in this proposal, provided that the equipment has been installedas supplied by Seller, without modification, is operated within the limits of ratedcapacity, generally approved practice and according to Seller’s instructions, andconsists of seaming can components made to the specifications supplied by Buyerand in accordance with generally accepted can industry quality and practice.

c. Where specifications for can size change parts supplied by Seller are establishedfrom sample can components furnished by Buyer, Seller warrants the equipmentto be suitable for the purpose intended only when a minimum of twenty-five samplecans and ends have been supplied by Buyer to enable Seller to test and adjust theequipment prior to shipment and then only where the can components being used byBuyer are identical with samples supplied to Seller for the purpose of establishingspecifications for the manufacture and testing of can size change parts.

d. Where specifications for can size change parts supplied by Seller are establishedfrom data sheets, drawings and/or dimensions of can components furnished byBuyer, Seller warrants the equipment to be suitable for the purpose intended only

where the can components being used by Buyer are identical with the data sheets,drawings and/or dimensions supplied to Seller for the purpose of establishingspecifications for the manufacture of said can size change parts and then onlywhere a minimum of twenty-five sample cans and ends have been supplied byBuyer to enable Seller to test and adjust the equipment prior to shipment.

e. Seller further warrants that the use or sale of the equipment furnished hereunderdoes not infringe any valid claim of any United States patent covering the goods.Seller shall defend and save Buyer harmless against any loss for infringement ofany valid United States patent covering the goods manufactured by Seller.

f. Seller makes no representations or warrants regarding the conformance of theequipment with, and shall not indemnify or hold harmless any person in connectionwith the violation of, any safety or health regulations which may be in force where theequipment will be used. Seller shall not be liable, and Buyer shall hold Sellerharmless, for any damage to person or property caused by or related to the use of the equipment in a manner other that as intended by Seller or by failure to utilize allsafety devices, guards and instruction supplied by Seller.


5/115


g. THE WARRANTY STATED HEREIN IS IN LIEU OF ALL OTHER WARRANTIES,EXPRESS OR IMPLIED, OF FITNESS FOR ANY PARTICULAR PURPOSE OROTHERWISE, OTHER THAN AS SET FORTH ABOVE, and Seller has notauthorized any person to make any other representations or warranties or otherwisesubject Seller to any liability in connection with the sale of Seller’s equipment.

LIABILITY:a. Any part or parts of the equipment sold hereunder manufactured by the Seller

(excepting parts subject to normal wear in use or breakage due to misuse), whichunder normal operating conditions and within twelve months from date of shipmentby Seller proves defective in material or workmanship as determined upon inspectionby the Seller, will be replaced or repaired Ex Works, point of shipment, provided thatBuyer within thirty days after discovering the same, notifies Seller in writing of thedefect and the particulars in connection therewith and establishes that the equipmenthas been properly installed, maintained and operating within limits of rated andgenerally approved usage and in accordance with the Seller’s instructions and that

no alterations or modifications have been made without Seller’s written approval.Components not of Seller’s manufacture are subject to component manufacturer’sstandard guarantee of service which will be made available to the Buyer to the extentavailable to the Seller. In no event shall Seller’s liability under this warranty exceedthe purchase price paid for the equipment.

b. Seller shall have no liability whatsoever to Buyer or others in any event for paymentof incidental or consequential damages, including, but not limited to, damages due toloss of use, loss of production, loss of product or cans, or loss of profit or othereconomic loss as a result of the use and operation of the equipment, including, butnot limited to, defective workmanship or materials or any delay, act, error or omission

of Seller.

MISCELLANEOUS:a. This agreement shall be governed by and interpreted according to the laws of the

State of California as applied to the residents of California entering into contractsto be wholly performed therein, without giving effect to principles of conflicts of laws.Each of the parties hereto submits to the jurisdiction of the state courts of Californiaand the United States federal courts of the Central District of California.

b. The terms hereof including those written within the body of this document shallconstitute the entire Agreement between the Buyer and Seller, and no change or

modification of this Agreement shall be binding on the Seller unless such a changeor modification shall be consented to in writing by an officer of the Seller.

c. If any party to this Agreement brings action to enforce its rights under this Agreement, the prevailing party shall be entitled to recover its costs and expenses,including without limitation, reasonable attorneys’ fees incurred in connection withsuch action.


6/115


7/115

60L SEAMER

ILLUSTRATION AND PARTS LIST INDEX

MACHINE AREA FIG. NO. PAGE NO.

BASE...................................................................................................................................1 ..................... 1

LOWER TURRET...............................................................................................................2 ..................... 5

LOWER CHUCK................................................................................................................3 ..................... 7

UPPER TURRET ................................................................................................................4 ..................... 9

UPPER TURRET (SEAMING SPINDLE)......................................................................... 5 ................... 13

UPPER TURRET (SEAMING LEVER)............................................................................. 6 ................... 15

CAN FEED AND DISCHARGE (CANNERY) .................................................................7 ................... 17

CAN FEED AND DISCHARGE (CAN SHOP)................................................................. 8 ................... 25

CAP FEED........................................................................................................................... 9 ................... 31

CAP FEED (SINGLE SEPARATOR) ..............................................................................10 ................... 35

DRIVE CASE.................................................................................................................... 11 ................... 39

TOOLS AND WRENCHES..............................................................................................12 ................... 45

MARKER (FOR CANNERY ONLY) ..............................................................................13 ................... 47

DRIVE PARTS W/ELECTRIC BRAKE .......................................................................... 14 ................... 51

SUPPLEMENTAL PARTS (CAN SHOP) ....................................................................... 15 ................... 55

SUPPLEMENTAL PARTS (CANNERY)........................................................................16 ................... 57

CHANGE PARTS (CANNERY ATMOSPHERIC).........................................................17 ................... 59

CHANGE PARTS (CAN SHOP)......................................................................................18 ................... 61

CHANGE PARTS (STEAM VACUUM) .........................................................................19 ................... 63

CAN FEED EXTENSION ................................................................................................20 ................... 65

16” WORM CAN FEED EXTENSION (CAN SHOP) .................................................... 21 ................... 71

FILLER DRIVE.................................................................................................................22 ................... 75


8/115


9/115

60L SEAMER

ILLUSTRATION AND PARTS LIST INDEX

MACHINE AREA FIG. NO. PAGE NO.

AUTOMATIC STOP (CANNERY).................................................................................. 23 ................... 77

AUTOMATIC STOP (CAN SHOP) .................................................................................24 ................... 81

FILLER DRIVE IN-MOTION TIMER............................................................................. 25 ................... 85

STEAM VACUUM...........................................................................................................26 ................... 87

MOTOR DRIVE (WOODS VARI-SPEED) .................................................................... 27 ................... 93

MOTOR DRIVE (REEVES VARI-SPEED).....................................................................28 ................... 95

COVER FEED CHUTE W/CONTROL............................................................................ 29 ................... 97

MOTOR DRIVE W/V BELT TYPE 213T TO 256T MOTOR FRAME ......................... 30 ................... 99

MOTOR DRIVE (VARI-SPEED)..................................................................................... 31 ................. 101

SEAMING ROLLS ...........................................................................................................32 ................. 103


10/115


1

60L BASE 60LB001.05

FIG. 1


11/115


Made in USA Copyright 2007 10/17/07 2

60L BASE 60LB001.05

FIG. 1

IND PART NO. QTY PART NAME

1 F0056L616AAAA5 1 INTERM SHAFT CLAMP WASHER

COM 1 .6250-11X1.2500 HX SOC HD CSCR2 26L854 REF SNAP IN BLANK (CANNERY ONLY)

3 F0004L654AAAB9 1 INTERMEDIATE GEAR GUARD

COM 4 .5000-13X.7500 HX HD CSCR

4 F0024L617AAAA3 1 INTERMEDIATE SHAFT RETAINING RING

5 F0057L616AAAA4 1 INTERM SHAFT UPPER WASHER

F0015L600AMAA7 1 INTERMEDIATE DRIVEN GEAR SUB-ASSY W/15L623

6 (F0016L623AAAA5) 1 CAP FEED TURRET DRIVE PINION

COM 2 1.4219X1.7500X2 BUSHING #1 GRV

7 (F0010L647AAAA3) 1 INTERMEDIATE DRIVEN GEAR KEY

COM 1 .1875X.6250 DOWEL PIN

8 (F0015L623AAAA6) 1 INTERMEDIATE DRIVEN GEARCOM 1 8X4 TAPER PIN

9 F0013L653AAAA1 1 INTERMEDIATE GEAR SHAFT COLLAR

COM 1 .3750-16X1 HX SOC SSCR

10 F0004L617AENP1 1 RETAINING RING -NICKEL PLATED 1.3750 SHAFT

11 F0009L644AAAA9 1 INTERMEDIATE GEAR SHAFT

12 F0503L654AAAA7 2 GUARD FOR BASE GEARING

COM 12 .2500-20X.5000 HX HD CSCR13 6L628 REF LOWER TURRET GUARD PIN

14 3L654 REF LOWER TURRET GUARD 3 PIECES

15 20L654 REF BASE COVER PLATE (FOR CAN SHOP ONLY)

16 F0010L644AAAA6 1 CAP FEED DRIVE SHAFT17 F0011L644AAAA5 1 CAP FEED TURRET HOLLOW DRIVE SHAFT

COM 1 1.4375X1.6250X2 BUSHING OILITE

18 F0026L617AENP5 1 RETAINING RING -NICKEL PLATED

19 F0014L653AAAA0 1 CAP FEED TURRET HOLLOW SHAFT SPACER

20 F0021L617AAAA6 1 CAP FEED TURRET SHAFT BEARING FLANGE

COM 1 .1250-27 HYDRAULIC FITTING - STR

COM 4 .5000-13X2 HX HD CSCR

21 F0001P615AAAA3 2 OIL SEAL

22 F0013L616AAAA7 1 BALL BEARING

23 F0731L643AAAA5 1 BASE


COM 1 1.1719X1.4375X2.7500 BUSHING #1 GRVCOM 4 .1250-27 HYDRAULIC FITTING - STR

COM 4 .1875TX.1250P MALE CONN

COM 72 .1875 OD TUBING

COM 1 .1250 PIPE PLUG (SLTD)

COM 4 .1250 ELBOW (ST)

COM 8 .3750-16X2.2500 HX SOC HD CSCR

COM 2 .3750X1 DOWEL PIN



12/115


3

60L BASE 60LB001.05

FIG. 1


13/115




COM 1 .1875X.7500 GRV PIN

COM 4 .1250X8.5000 NIPPLE

COM 4 .1250 NPT CPLNG

COM 3 8X4.5000 TAPER PIN

COM 4 .1250TX.2500-28 MALE CONN

COM 4 .1250X.1250 HI-SEAL ELBOW

COM 85 .1250 TUBING

COM 4 .2500-28 HYDRAULIC FITTING STR

(F0924L654AAAA3) 1 LUBE ID PLATE

24 F0011L647AAAB0 1 CAP FEED TURRET GEAR HUB KEY

25 F0004L615AAAA9 1 OIL SEAL

26 F0025L623AAAA4 1 CAP FEED TURRET GEAR HUB

COM 1 .5000-13X1.5000 HX HD CSCR

COM 2 .5000-13X1.2500 SQ HD SCR

27 F0020L616AAAA8 1 BEARING LOCKWASHER #W-11

28 F0021L616AAAA7 1 BEARING LOCKNUT #N-11

29 F0005L617AAAA6 1 RETAINING RING 2.375 SHAFT

30 F0011L616AAAA9 1 BALL BEARING 2.3622X4.3307X.8661

31 F0017L623AAAA4 1 CAP FEED TURRET GEAR

COM 6 .5313X1.2500X.1250 WSR (SAE)

COM 6 .5000-13X1.7500 HX HD CSCR

32 F0012L647AAAA1 1 CAP FEED DRIVE PINION KEY

33 F0020L617AAAA7 1 CAP FEED DRIVE PINION BEARING RETAINER

COM 6 .3750-16X.7500 HX HD CSCR

34 F0021L623AAAA8 1 CAP FEED DRIVE PINION

COM 1 10-24X.7500 HX SOC HD CSCR

COM 1 .5000-13X.7500 HX SOC SSCR

35 F0024L643AAAA1 4 BASE LEG36 34L654 REF BASE TERMINAL PAD COVER (CAN SHOP ONLY)

37 F0072L616AAAA5 1 SWITCH LEVER SHAFT BUSHING

38 F0730L643AAAA7 1 BASE TOP PLATE

39 F0733L643AAAA1 1 BASE TROUGH

COM 13 .2500-20X.5000 HX HD CSCR

COM 13 .2500 WSR (FLT)

PARTS ARE NOT SHOWN

F0108L614AAAA5 1 LUBRICATION BLOCK

COM 2 .2500-20X1.1250 HX HD CSCR


F0024M226AAAA8 1 ANAEROBIC SEALANT LOCTITE 573

F0025M226AAAA5 1 PRIMER LOCTITE 7649

F0176H644AAAA6 1 EXTENSION WORM SHAFT


F0897L654AAAA1 1 GUARD FILLER DRIVE

F0903L654AAAA7 1 LATCH FEED SPROCKET GUARD

COM 4 10-24X.6250 SOC CSCR


14/115


5

60L LOWER TURRET 60LB021.10

FIG. 2


15/115



60L LOWER TURRET 60LB021.10

FIG. 2

IND PART NO. QTY PART NAME1 S0475L644AAAA3 1 LOWER TURRET HOLLOW SHAFT

COM 1 1.8750X2.2500X2 BUSHINGCOM 6 .5000-13X1.2500 HX HD CSCR

2 F0070L617AAAA6 6 LOWER CHUCK SLIDE BEARING - CLAMP

COM 6 .5000-13X1.2500 HX HD CSCR3 F0007H628AAAA0 2 DOWEL PIN .498X.500X1.00LG4 S0078L627AAAA5 1 LOWER TURRET TOP

5 F0150L623AAAA1 1 LOWER CHUCK DRIVE GEAR

6 F0066L617AAAA2 1 BEARING RETAINER

COM 6 .3125-18X.7500 HX SOC HD CSCR

COM 1 .0625-27 PIPE PLUG (SOC HD)

7 F0008H616AAAA3 1 BALL BEARING 2.7559X4.3307X1.4173W

8 F0006L617AAAA5 2 RETAINING RING 2.7500 DIA SHAFT

9 79L627 1 LOWER TURRET BOTTOMCOM 6 .3750-16X2 SOC CSCR

COM 1 .7500 PIPE PLUG (SOC HD)

F0007H628AAAA0 2 DOWEL PIN .498X.500X1.00LG


10 F0012S815AAAA9 1 O-RING .375X.500X.070W

11 F0022L620AAAA0 1 LOWER CHUCK CAM

12 F0067L620AAAA6 1 LOWER CHUCK RETURN CAM

13 F0017L617AAAA2 1 LOWER TURRET BEARING FLANGE


14 F0009L615AAAA4 2 OIL SEAL 3.4386X4.500X.469W

15 F0015L616AAAA5 1 BALL BEARING 2.7559X4.9213X1.5625W

16 F0339L653AAAA6 1 SEAL SLEEVE (SS)17 F0007L615AAAA6 1 OIL SEAL 3.750X4.928X.625W

18 F0008L647AAAB5 2 LOWER TURRET GEAR KEY

19 F0018L623AAAA3 1 LOWER TURRET GEAR - RH 78T 7P 18 DEG 30'


21 F0023L616AAAA5 1 BEARING LOCKNUT N-14

22 F0822L654AAAA1 1 LOWER TURRET GUARD


23 F0006L628AAAA2 4 LOWER TURRET GUARD PIN

24 F0474L644AAAA5 1 VERTICAL DRIVE SHAFT

25 F0026P216AAAA7 1 BALL BEARING (SHIELDED) 214-K

26 F0018L617AAAA1 1 INTERM DRIVE PINION BEARING RETAINER

COM 6 .3750 WSR (INT/SHPF)COM 6 .3750-16X.7500 HX HD CSCR

27 F0148L623AAAA6 1 INTERMEDIATE DRIVE PINION 44T 7P



16/115


7

60L LOWER CHUCK 60LB021.10

FIG. 3


17/115



60L LOWER CHUCK 60LB021.10

FIG. 3

IND PART NO. QTY PART NAME1 7L826 REF LOWER CHUCK PLATE SCREW (CAN SHOP ONLY)

2 L837 REF LOWER CHUCK FLANGE PLATE (CAN SHOP ONLY)3 L837 REF LOWER CHUCK PLATE

4 F0008L826AAAA0 6 LOWER CHUCK SPRING SCREW

5 F0044L627AAAA7 6 LOWER CHUCK SLIDE SHIELD TOP6 371L616 12 SHIM WASHER .002-.005-.010-.030 THK

7 F0071L627AAAA3 6 LOWER CHUCK MANDREL TOP

8 F0041L817AENP4 6 SNAP RING -NICKEL PLATED 2.440 BORE

9 F0116L816AAAA1 6 BALL BEARING 1.3780X2.4409X1.1024 W

10 F0137L815AAAA9 12 O-RING ENCAPSULATED 2.4375X2.6250X.093W

11 F0004P116AAAA4 6 BEARING LOCKWASHER 1.378


12 F0082L627AAAA6 6 LOWER CHUCK SLIDE TOP


13 F0021L816AAAA5 6 LOWER CHUCK SPRING WASHER14 F0009L840AAAA1 6 LOWER CHUCK SPRING 0 TO 450 LB RANGE

15 F0009L826AAAA9 6 LOWER CHUCK BOTTOM MANDREL SCREW

16 F0156L623AAAA5 6 LOWER CHUCK GEAR 22T 8P

17 F0047L627AAAA4 6 LOWER CHUCK MANDREL BOTTOM

COM 6 606 (#9) WOODRUFF KEY

F0056L828AAAA9 6 DOWEL PIN .187 DIA X .250 LG

18 F0004P517AAAA9 6 SNAP RING (BEVELED) 1.850 BORE

19 F0028P516AAAA2 6 BALL BEARING .7874IDX1.8504ODX.8125W

20 F0078L641AAAA8 6 SEAMING ROLL RETAINER

21 F0029L826AAAA5 6 SEAMING ROLL RETAINER SCREW

22 F0069L627AAAA7 6 LOWER CHUCK SLIDE BEARING

COM 18 10-24X.2500 HX SOC SSCR

COM 12 .0937X.3750 COILED PIN

23 F0050L627AAAA8 6 LOWER CHUCK SLIDE BLOCK BOTTOM

COM 6 .3125-18X.7500 HX SOC CSCR (W/NYL)

24 F0073L627AAAA1 6 LOWER CHUCK SLIDE BOTTOM

COM 6 .3125-18X.3750 HX SOC SSCR (H/DG W/NYL)

25 F0015L629AAAA0 6 LOWER CHUCK ROLL PIN


F0136L614AAAA1 6 INDICATOR PORT

COM 6 .1250T TUBE NUT


26 F0601P629AAAB9 6 LOWER CHUCK RETURN CAM ROLL

27 F0032L847AAAA5 6 WOODRUFF KEY

COM 6 .0938X.3750 SPRING PIN28 F0093L816AAAB6 6 WASHER .8906X1.9375X.050T

29 F0003P229AAAA9 6 (A) CAM ROLL-MICROPLATE

30 F0135L614AAAA2 6 GASKET DIVIDER BLOCK

31 F0141L614AAAA8 6 DIVIDER BLOCK

COM 12 8-32X1.5000 HX SOC CSCR


18/115


9

60L UPPER TURRET 60LB021.10

FIG. 4A


19/115




FIG. 4A


1 F0055L623AAAA7 1 SEAMING SPINDLE DRIVE GEAR 69T 8P

COM 1 10-24X.3750 HX SOC HD CSCR2 F0001L647AAAB2 1 SEAMING SPINDLE DRIVE GEAR KEY

3 F0016L616AAAA4 1 BALL BEARING 2.7559X4.9213X1.5625

4 F0006L617AAAA5 1 RETAINING RING 2.7500 DIA SHAFT

5 F0003L615AAAA0 2 OIL SEAL 2.750X3.750X.437W6 F0001L641AAAA0 1 SEAMING TURRET W/257L616 BUSHING

COM 2 .3750X1.5000 DOWEL PIN

COM 6 .6250-11X4 HX SOC HD CSCR

COM 72 .4063X.8125X.1250 WSR


COM 1 .3125X1 GRV PIN


7 F0257L616AAAA2 24 IRON BUSHINGP-1248C-2000 1.250X1.5000X2.0008 F0020L615AAAA9 1 O-RING 5.125X5.375X.139W9 F0034L828AAAA6 2 DOWEL PIN .498X.500X1.00LG

10 F0334L641AAAA8 1 UPPER TURRET DRIVE HUB

COM 6 .5000-13X1.7500 HX HD CSCR


COM 2 10-24X.6250 SOC CSCR11 F0001P254AAAA9 2 HEX SOCKET SET SCREW (SS)12 F0003L647AAAA2 1 SEAMING TURRET DRIVE HUB KEY

13 F0010L608AAAK8 1 SEAMING CHUCK BELL HUB

COM 6 .3750-16X1.2500 HX HD CSCR


COM 6 .3750-16X.7500 HX SOC HD CSCR14 F0050L608AAAC7 1 SEAMING STAR HUB

COM 6 .3750-16X1.7500 HX HD CSCR




ITEM# 15~25, 28~38, SEE NEXT PAGE

26 F0060L616AAAA9 12 HARDENED STEEL BALL .3125 DIA

27 F0017L640AAAA3 12 SEAMING LEVER TAKE-UP SPRING39 68L654 REF NUMBERS 1 THRU 6


20/115


11


FIG. 4B


21/115




FIG. 4B


15 F0006L640AAAA6 1 SEAMING CAM SPRING

16 F0007L626AAAA3 1 SEAMING CAM SPRING SCREW17 F0030L628AAAA2 1 SEAMING CAM ECCENTRIC PIN

COM 1 .2500X1.5000 GRV PIN

18 F0129L616AAAA8 1 SEAMING CAM ECCENTRIC BUSHING

19 F0130L616AAAA5 1 SEAMING CAM ECCENTRIC BEARING

COM 2 .3750-16X1.5000 SOC HD CSCR

COM 2 .4063X.8125X.0625 WSR


20 F0004L647AAAA1 1 SEAMING CAM KEY

21 F0022L653AAAA0 1 OILER BRUSH COLLAR


22 F0003L614AAAA1 1 KNOCKOUT ROD OILER BRUSH

23 F0002L620AAAA4 1 SEAMING CAM SECTION -2ND OPERATIONCOM 1 .3750-16X.7500 HX SOC SSCR

COM 1 .3125X.1250 PLUG

24 F0001L620AAAA5 1 SEAMING CAM -1ST OPERATION

COM 1 .1875X1.5000 COTTER PIN


25 F0011L620AAAA3 1 KNOCKOUT CAM


COM 2 .4063X.8125X.0625 WSR

28 F0015L641AAAA4 1 SEAMING CAM HUB


29 F0017L626AAAA1 2 CAP CENTERING CAM HOLLOW SCREW

COM 2 .3750-16X3 HX HD CSCRCOM 2 .6250-11 HX NUT (JAM)

30 F0016L641AAAA3 1 CAP CENTERING CAM HOLDER


COM 2 .4063X.8125X.0625 WSR

31 F0018L626AAAA0 1 SEAMING CAM PIVOT PIN SCREW

COM 1 .2500-28 HYD LUBE FIT 90 DEG

COM 1 .5000 WSR (LOCK)

32 F0004L628AAAA4 1 SEAMING CAM PIVOT PIN

COM 1 .1250X.5000 GRV PIN

33 F0010L620AAAA4 1 CAP CENTERING CAM

34 F0005L653AAAA1 1 SEAMING CAM SPACER

35 F0012L617AAAA7 1 SEAMING TURRET UPPER BEARING RETAINERCOM 6 .3750-16X1.2500 HX HD CSCR

36 F0014L616AAAA6 1 BALL BEARING 2.7559X4.9213X.9449




22/115


13


FIG. 5 SEAMING SPINDLE


23/115




FIG. 5 SEAMING SPINDLE


1 F0001L640AAAA1 6 KNOCKOUT ROD SPRING

2 F0002L653AAAA4 12 KNOCKOUT ROD COLLAR3 F0102L616AAAA9 6 BALL BEARING 1.5748X2.6772X1.181W4 F0345L644AAAA2 6 SEAMING SPINDLE SHAFT & GEAR 22T 8P

COM 24 .3750-16X1.2500 HX HD CSCR

COM 6 6X2 TAPER PIN

5 F0283L616AAAA0 6 SEAMING SPINDLE LOWER BEARING WASHER

6 F0006L616AAAA6 6 DOUBLE ROW ROLL BEARING

7 F0284L616AAAA9 6 SEAMING SPINDLE SLEEVE WASHER

8 F0052L816AAAA7 18 SEAMING SPINDLE SHIM .003 THK

F0052L816AAAB5 18 SEAMING SPINDLE SHIM .005 THK

F0052L816AAAC3 12 SEAMING SPINDLE SHIM .010 THK

9 F0211L653AAAA1 6 SEAMING SPINDLE SEAL SLEEVE

10 F0002L615AAAA1 6 OIL SEAL 2X2.75X.5011 F0011L617AAAA8 6 SEAMING SPINDLE LOWER BEARING RETAINER

12 F0008L616AAAA4 6 BALL BEARING .700X1.8504X.820

13 F0031L617AAAA4 6 SEAMING SPINDLE UPPER BEARING RETAINER


COM 12 .2500-20X.5000 HX HD CSCR

14 F0002L616AAAA0 6 BALL THRUST BEARING .625X1.125X.343

15 F0035L617AAAA0 6 RETAINING RING


24/115


15


FIG. 6 SEAMING LEVER


25/115




FIG. 6 SEAMING LEVER


1 F0002L641AAAA9 6 SEAMING CAM LEVER -1ST OPERATION

2 F0002L617AENP3 12 RETAINING RING -NICKEL PLATED .750 SHAFT3 F0023L640AAAA5 6 SEAMING CAM LEVER SPRING

4 F0001L629AAAA6 6 SEAMING CAM ROLL PIN -1ST OPER


5 F0003L644AAAC1 12 SEAMING LEVER SHAFT

COM 12 .3125-18X.5000 HX HD CSCR (W/NYL)

COM 12 .3438X.8750X.0625 WSR

COM 12 .8125X1.8750X.1250 WSR

6 F0059L616AAAA2 12 FLEXLOC NUT 3/4-16 NF

7 F0003L641AAAA8 6 SEAMING CAM LEVER -2ND OPERATION

8 F0003L629AAAA4 12 SEAMING CAM ROLL

9 F0001L626AAAA9 12 SEAMING ADJUSTMENT SCREW

10 F0004L641AAAA7 12 SEAMING ADJUSTMENT LEVERCOM 12 .3750-16X1.2500 HX SOC HD CSCR


11 F0029L616AAAA9 12 SEAMING LEVER SHAFT WASHER

12 F0015L617AAAA4 12 SEAMING LEVER SHAFT RING

13 F0002L629AAAA5 6 SEAMING CAM ROLL PIN - 2ND OPERATION


14 F0152L616AAAA8 12 SEAMING LEVER SHAFT LOWER WASHER .094+.010 THK

15 F0083L641AAAA1 12 SEAMING ROLL LEVER W/65L614 SMG LEVER PLUG


COM 12 .4375X.1250 PLUG


F0065L614AAAA6 12 SEAMING LEVER PLUG16 F0044L626AAAA8 12 SEAMING ROLL LEVER SET SCREW

17 F0081L641AAAA3 12 SEAMING ROLL PIN

18 F0212L616AAAA6 12 SEAMING ROLL UPPER SEAL/SHIELD

19 F0028L615AAAA1 12 OIL SEAL 1.974 X 2.265 X .185

20 F0078L641AAAA8 12 SEAMING ROLL RETAINER

21 F0029L826AAAA5 12 SEAMING ROLL RETAINER SCREW

22 F0198L616AAAA4 12 SEAMING ROLL BOTTOM CLOSURE

23 F0048L617AAAA5 12 SNAP RING 1.750 BORE SS


26/115


17

60L CAN FEED AND DISCHARGE 60LB004.06

FIG. 7A CANNERY


27/115




FIG. 7A CANNERY


1 F0078P290AAAA3 1 WASHER .5313IDX1.6875X.3750

COM 1 .5000-13X1.5000 HX HD CSCR2 F0004L624AAAA8 1 FEED DRIVE SPROCKET HUB

COM 3 .5000 WSR

COM 3 .5000-13X1.5000 HX HD CSCR3 F0003L624AAAA9 1 FEED DRIVE SPROCKET 48T .75P4 F0177L616AAAA9 1 THRUST WASHER 1.4375

5 F0015L647AAAA8 2 FEED DRIVE SPROCKET SHAFT KEY

6 F0128L644AAAB3 1 FEED DRIVE SPROCKET SHAFT


COM 1 .5000-13X1.2500 HX HD CSCR7 F0645L643AAAA0 1 FEED DRIVE CASE

COM 2 1.1875X1.4375X2.5000 BUSHING #1 GRV

COM 1 .5000-13X2.5000 HX SOC HD CSCRCOM 2 .5000-13X1.7500 HX HD CSCR


COM 2 .5000-14 NPT PIPE PLUG (HX SOC)

COM 2 .1250-27 65 DEG HYDRAULIC FITTING



COM 2 .3750X1.5000 DOWEL PIN8 F0022P216AAAA1 2 THRUST WASHER9 F0006L623AAAA7 1 FEED DRIVE SPIRAL GEAR 36T 6P

COM 1 6X2.5000 TAPER PIN10 F0154L616AAAA6 1 SEALMASTER BEARING

11 F0040L615AAAA5 1 FEED DRIVE CASE GASKET12 F0126L654AAAA4 1 FEED DRIVE CASE SIDE COVER W/58L614 OIL GAUGE



13 (F0058L614AAAA5) 1 OIL GAUGE .6250

14 F0006L654AAAA9 1 FEED DRIVE CASE TOP COVER

COM 4 .2500-20X.5000 RD HD MSCR15 F0030L616AAAA6 2 FLEXLOC NUT

16 F0014L647AAAA9 2 FEED DRIVE SHAFT KEY

COM 2 .1250X.5000 DOWEL PIN17 F0005L623AAAA8 1 FEED DRIVE SPIRAL PINION 12T 6P18 F0050L616AAAA1 1 DRIVE SPIRAL PINION WASHER

19 F0012L615AAAA9 1 O-RING 1.1875X1.4375X.1250W20 F0015L653AAAB7 1 SAFETY CLUTCH SHAFT COLLAR


COM 1 .3750-16X.3750 HX SOC SSCR21 F0020L623AAAA9 1 FEED DRIVE PINION 26T 7P RH


22 F0003L697AAAA1 1 SAFETY CLUTCH DRIVEN HUB

COM 4 M10X1.5X25 HX SOC HD CSCR



28/115


19


FIG. 7A CANNERY


29/115



23 F0048L616AAAA6 2 STEEL BALL (HARDENED) .62 D

24 F0002L697AAAA2 1 SAFETY CLUTCH DRIVE PLATE

25 F0001L697AAAA3 1 SAFETY CLUTCH DRIVE HUB

COM 2 .3750X.7500 DOWEL PIN (HRD)26 F0008L640AAAA4 3 SAFETY CLUTCH SPRING27 F0012L644AAAA4 1 FEED DRIVE SHAFT VERTICAL

COM 1 .1250X.5000 GRV PIN28 F0049L616AAAA5 1 SAFETY CLUTCH SPRING WASHER

29 F0736L654AAAA6 1 FEED DRIVE GUARD W/47L616 CLUTCH DISC BALL30 F0047L616AAAA7 1 CLUTCH DISC BALL .5000 DIA31 F0061L628AAAA4 1 PIN FEED DRIVE GUARD

32 F0026L854AAAA3 1 CLOSURE/SNAP-IN BLANK .7500


30/115


21


FIG. 7B CANNERY


31/115




FIG. 7B CANNERY


1 F0001L645AAAB4 1 DISCHARGE STAR HUB 202/204 X 214/506

COM 8 .3750-16X.7500 HX SOC HD CSCRCOM 1 .3750-16X1.2500 HX SOC HD CSCR

2 F0014L644AAAA2 1 DISCHARGE SHAFT

COM 1 1210 WOODRUFF KEY3 F0254L616AAAB3 2 EXTENSION TABLE SHIM

COM 2 10-24X.5000 FLT HD MSCR4 F0006L643AAAA3 1 DISCHARGE BRACKET

COM 1 .2500-28 45 DEG HYD FIT

COM 1 1.4375X1.7500X2.5000 BUSHING #1 GRV5 F0004L617AENP1 2 RETAINING RING -NICKEL PLATED 1.3750 SHAFT

6 F0043L853AAAA3 1 DISCHARGE INTERMEDIATE SHAFT COLLAR1.4375


7 F0177L616AAAA9 1 THRUST WASHER 1.43758 F0022P216AAAA1 1 THRUST WASHER9 F0019L623AAAA2 1 DISCHARGE GEAR 52T 7P


10 F0021L653AAAA1 1 SET COLLAR .6250 SHAFT


11 F0024L644AAAA0 1 DISCHARGE RAIL SHAFT12 F0013L640AAAA7 1 DISCHARGE RAIL SPRING13 F0016L626AAAA2 1 DISCHARGE RAIL SPRING SCREW

COM 1 .3750-16 HX NUT14 F0382L616AAAA3 2 SHIM-DISCHARGE BRACKET .003 THK

F0382L616AAAB1 2 SHIM-DISCHARGE BRACKET .005 THK

F0382L616AAAC9 1 SHIM-DISCHARGE BRACKET .010 THK15 F0003L646AAAA3 1 DISCHARGE RAIL STOP LEVER


COM 1 .2500-20 HX NUT


COM 2 .3750-16 HX NUT

COM 1 .3750-16X1.5000 HX HD CSCR

COM 1 .3750-16X2.7500 HX HD CSCR

16 F0003L669AAAA5 1 FEED CHAIN GUIDE RAIL


17 F0004L669AAAA4 1 FEED CHAIN WEAR STRIP

COM 5 10-24X.6250 FIL HD MSCR

18 F0001L669AAAA7 1 FEED CHAIN COVER RAILCOM 1 .3750-16X.7500 HX HD CSCR

COM 1 .3750-16X2.2500 HX HD CSCR

COM 1 .3750-16 LOCKSCREW DRILL BUSHING


19 F0007L669AAAA1 1 FEED TABLE WEAR PLATE

COM 1 .2500-20X.7500 FLT HD MSCR

20 F0089L653AAAA0 1 FEED CHAIN WEAR STRIP SPACER 2ND

21 F0088L653AAAA1 1 FEED CHAIN WEAR STRIP SPACER


32/115


23


FIG. 7B CANNERY


33/115



22 F0005L643AAAA4 1 FEED TABLE

COM 2 .5000-13X2.5000 HX HD CSCR

COM 2 .3750-16 HX NUT

COM 2 .3750-16X1.2500 HX HD CSCR

COM 2 .6250-11X1.7500 HX HD CSCR

COM 1 .6250X.8125X1.1875 BUSHING #5 GRV

COM 3 .6250-11X2.5000 HX HD CSCR

COM 3 .5000-13X1.7500 HX HD CSCR


COM 2 10-24X1.5000 HX SOC HD CSCR


23 F0024L654AAAA7 1 FEED DRIVE SPROCKET SHIELD

COM 2 .2500-20X.5000 RD HD MSCR

24 F0006L669AAAA2 1 FEED CHAIN RETURN HOLD DOWN

25 F0201L669AAAA5 1 FEED CHAIN RETURN SUPPORT

COM 2 .2500-20 HX NUT



26 F0202L669AAAA4 1 FEED CHAIN SUPPORT SECTION


COM 4 .2500-20 HX NUT


27 F0203L669AAAA3 2 FEED CHAIN SUPPORT BRACKET


34/115


25


FIG. 8A CAN SHOP


35/115




FIG. 8A CAN SHOP


1 F0020L669AAAA4 1 FEED TABLE WEAR PLATE

COM 6 .2500-20X.6250 FLT HD MSCR2 F0001L645AAAB4 1 DISCHARGE STAR HUB 202/204 X 214/506



3 F0014L644AAAA2 1 DISCHARGE SHAFT

COM 1 1210 WOODRUFF KEY

4 F0006L643AAAA3 1 DISCHARGE BRACKET

COM 1 .2500-28 45 DEG HYD FIT



6 F0004P253AAAB5 2 PLAIN COLLAR 1.438 X 2.2500 X .750


7 F0177L616AAAA9 1 THRUST WASHER 1.43758 F0022P216AAAA1 6 THRUST WASHER

9 F0019L623AAAA2 1 DISCHARGE GEAR 52T 7P


10 F0019L669AAAA7 1 FEED STAR CLAMP RING


11 F0018L669AAAA8 1 FEED DISC

COM 10 .2500-20X.6250 FLT HD MSCR

12 F0032L623AAAA5 1 FEED DISC GEAR 115T 8P


13 F0028L644AAAA6 1 FEED DISC SHAFT


COM 1 .1250-27 65 DEG HYDRAULIC FITTING14 F0024L647AAAA7 1 FEED DISC PINION KEY

15 F0031L623AAAA6 1 FEED DISC PINION 23T 8P


16 F0021L643AAAA4 1 FEED TABLE



COM 18 .1875 OD TUBING




COM 1 .6250X.8125X1.1875 BUSHING #5 GRV

COM 2 10-24X1.5000 HX SOC HD CSCRCOM 3 .1875X.5000 DOWEL PIN





COM 2 .6250-11X1.7500 HX HD CSCR




36/115


27


FIG. 8A CAN SHOP


37/115




18 F0003L646AAAA3 1 DISCHARGE RAIL STOP LEVER


COM 1 .2500-20 HX NUT


COM 2 .3750-16 HX NUT

COM 1 .3750-16X1.5000 HX HD CSCR

COM 1 .3750-16X2.7500 HX HD CSCR

19 F0013L640AAAA7 1 DISCHARGE RAIL SPRING

20 F0016L626AAAA2 1 DISCHARGE RAIL SPRING SCREW

COM 1 .3750-16 HX NUT

21 F0024L644AAAA0 1 DISCHARGE RAIL SHAFT

22 F0013L682AAAA6 REF CAP TRIP ROD

23 F0007P582AAAA6 REF CAP TRIP ROD BALL JOINT 90° ROD THRU

24 F0079L644AAAA4 1 CAN FEED SHAFT UPPER

25 F0031L697AAAA7 1 SAFETY CLUTCH DRIVEN HUB #6X2.2500 TAPER PIN


26 F0048L616AAAA6 2 STEEL BALL (HARDENED) .62 D

27 F0002L697AAAA2 1 SAFETY CLUTCH DRIVE PLATE28 F0014L647AAAA9 1 FEED DRIVE SHAFT KEY


29 F0030L697AAAA8 1 SAFETY CLUTCH DRIVE HUB

COM 2 .3750X.7500 DOWEL PIN (HRD)

30 F0008L640AAAA4 3 SAFETY CLUTCH SPRING

31 F0018L628AAAA8 REF CAP TRIP LEVER PIN

32 F0011L682AAAA8 REF CAP TRIP FINGER

33 F0012L682AAAA7 REF CAP TRIP LEVER

34 F0009L653AAAA7 REF COLLAR .5000 SHAFT

35 F0025L626AAAA1 1 CAN FEED HOLD DOWN STUD

36 F0136L669AAAA5 1 CAN FEED HOLD DOWN


COM 2 .2500-20 HX NUT


37 F0135L669AAAA6 1 CAN FEED HOLD DOWN BRACKET

38 F0028L653AAAA4 1 SET COLLAR - STEEL .7500

39 F0116L616AAAA3 1 SAFETY CLUTCH SPRING WASHER

40 F0005P253AAAB4 2 COLLAR 1.187


41 F0080L644AAAA1 1 CAN FEED SHAFT LOWER

42 F0023L647AAAA8 1 FEED DRIVE PINION KEY


43 F0030L623AAAA7 1 FEED DRIVE PINION 26T 7P


ITEMS 22, 23, 31, 32, 33, 34

NOT USED WITH SINGLE ROLL SEPARATOR


38/115


29


FIG. 8B CAN SHOP


39/115




FIG. 8B CAN SHOP


1 F0014P154AAAA5 1 KNOB

2 F0621L654AAAA4 3 CAN FEED GUARD SUPPORT BRACKETCOM 3 .5000X.1500 BUMPON TAPE - BLACK

3 F0622L654AAAA3 2 CAN FEED SUPPORT BRACKET

COM 2 .3750-16X.7500 HX HD CSCR

COM 2 .3750 WSR (SHD)

4 F0623L654AAAA2 1 CAN FEED GUARD SUPPORT BRACKET

COM 1 .3750-16X.5000 HX HD CSCR

COM 1 .4063X.8125X.0625 WSR

COM 2 .5000X.1500 BUMPON TAPE - BLACK

5 F0618L654AAAA9 1 CAN FEED & DISCHARGE GUARD -TOP


COM 2 .4060X1X.0625 WSR

COM 14 10-24X.6250 HX HD CSCRCOM 14 10 WSR

COM 14 10-24 HX NUT

COM 3 .2500-20X.7500 HX HD CSCR

COM 3 .2570X.5000X.0938 WSR

COM 1 .5000X.1500 BUMPON TAPE - BLACK

COM 1 .7500X.3750 HEMI (BUMPON) GREY

6 F0620L654AAAA5 1 CAN FEED & DISCHARGE GUARD -SIDE

COM 2 .2500-20X.6250 HX HD CSCR

COM 2 .2570X.5000X.0938 WSR

7 F0619L654AAAA8 1 CAN FEED &DISCHARGE GUARD -FRONT

COM 2 .2500-20X.7500 HX HD CSCR

COM 2 .2500 WSR


40/115


31

60L CAP FEED 60LB005.14

FIG. 9


41/115




FIG. 9


1 F0006L615AAAA7 1 OIL SEAL 3.750X4.723X.468W

2 F0008L617AENP7 1 RETAINING RING -NICKEL PLATED 3.344 SHAFT3 F0017L616AAAA3 1 BALL BEARING 3.3465X5.1181X.8661W


5 F0023L617AAAA4 1 CAP FEED TURRET BEARING RETAINER

6 F0013L647AAAA0 1 CAP FEED TURRET HOLLOW SHAFT KEY

7 F0021L644AAAA3 1 CAP FEED TURRET HOLLOW DRIVEN SHAFT


8 F0019L647AAAA4 1 CAP FEED HOLLOW DRIVE SHAFT KEY


9 F0001L670AAAB2 1 CAP FEED TURRET HUB

COM 2 .3750X1.2500 DOWEL PIN


COM 16 .3750-16X.7500 HX SOC HD CSCR10 F0322L653AAAA7 1 RAIL HOLDER

COM 1 .3750-16X.7500 HX HD CSCR


11 F0014L656AAAA7 1 CAP FEED DRAG MAGNET HOLDER

COM 1 .3750-16X1 HX SOC HD CSCR (W/NYL)12 F0014L633AAAA5 1 CAP FEED DRAG MAGNET

13 F0024L626AAAA2 1 CAP FEED DRAG MAGNET SCREW

14 21L654 REF CAP FEED BRACKET GUARD (CAN SHOP ONLY)

15 104L654 REF CAP FEED BRACKET SPLASH STRIP (CANNERY ONLY)

16 787L654 REF CAP FEED BRACKET GUARD – BOTTOM (CANNERY ONLY)

COM 3 HEX HD CAPSCREW .2500-20X1.0 SS

COM 3 STD WASHER .2500 SSCOM 1 JIFFY CLAMP #125

796L654 REF CAN FEED BRACKET GUARD – BOTTOM (CAN SHOP ONLY)

COM 2 HEX HD CAPSCREW .2500-20X1.0 SS

COM 2 STD WASHER .2500 SS

COM 1 JIFFY CLAMP #125

17 F0117L616AAAA2 1 CAP FEED BRACKET SUPPORT SHIM .020 THK

F0117L616AAAB0 1 CAP FEED BRACKET SUPPORT SHIM .010 THK

18 F0016L643AAAA1 1 CAP FEED BRACKET SUPPORT

19 F0005L617AAAA6 1 RETAINING RING 2.375 SHAFT

20 F0012L616AAAA8 1 BALL BEARING 2.3622X1.3307X.8661W

21 F0020L647AAAB9 1 SEPARATOR DRIVE GEAR KEY

22 F0003L623AAAA0 1 MARKER DRIVE MITER GEAR 32T 8P23 F0022L623AAAA7 1 SEPARATOR DRIVE GEAR 39T 12P



24 F0016L653AAAA8 1 CAP FEED BRACKET STEADY SPACER

25 F0692L643AAAA2 1 CAP FEED BRACKET


COM 5 .3750-16X2 SOC CSCR



42/115


33


FIG. 9


43/115



COM 2 .3750-16X1.2500 HX HD CSCR


COM 2 .3750-16X2.2500 HX HD CSCR

COM 2 .3125X.2500 PLUG



26 F0018L656AAAA3 1 CAP PUSHER SAFETY STRIPPER

PARTS ARE NOT SHOWN

F0018L833AAAC5 1 SEALING FITTING .5000"

F0901L833AAAO8 36 CABLE -3 COND 18AWG OLFLEX


44/115


35


FIG. 10A SINGLE SEPARATOR


45/115




FIG. 10A SINGLE SEPARATOR

IND PART NO. QTY PART NAME1 F0774L654AAAA9 1 SINGLE SEPARATOR GUARD

COM 1 .3750-16X.5000 HX HD CSCRCOM 1 M10.5X30X2.5 WSR (FLT)2 L656 REF GUIDE HOLDER3 F0672L643AAAA6 1 SEPARATOR SPINDLE HOUSING

COM 1 M10X1.5X50 HX HD CSCRCOM 1 M10X1.5 HX NUTCOM 1 .2500-32 UNEF GRAVITY FEED "L" OIL CUP

4 F0305L639AAAA7 1 AIR CYLINDER 20MM BOREX5MM STROKECOM 2 10-24X1.7500 HX SOC HD CSCR

5 F0054L682AAAA6 1 ROD ENDCOM 1 M5X.8X20 HX SOC SSCR

6 F0350L616AAAA8 3 BUSHING 10MM X 12MM X 7MM7 F0671L643AAAB5 1 SEPARATOR BRACKET

COM 2 .3750-24X1.2500 HX HD CSCR

COM 1 .2500-20X.5000 HX SOC HD CSCRCOM 2 .3125-18X1.2500 HX HD CSCRCOM 2 .4063X.8125X.0625 WSRCOM 2 .2500X1 SPRING PINCOM 1 .2500 WSR (FLT)COM 2 .3125 WSR

8 F0346L616AAAA5 2 NEEDLE BEARING 20MM X 26MM X 20MM9 F0043L615AAAA2 1 OIL SEAL 20MM X 26MM X 4MM

10 F0168L656AAAA1 1 SEPARATOR SPINDLE11 F0819L654AAAA6 1 REAR GUARD

COM 1 .6250X.0600 TUBINGCOM 18 .0625 FLEXIBLE TRIM FLEXIBLE TRIMCOM 1 .4063X.8125X.0625 WSRCOM 1 .3750-16X1.2500 HX HD CSCR

12 F0307L639AAAA5 2 MALE HOSE CONNECTOR .25X10-3213 F0094L624AAAA9 1 CHAIN LINK #50 SS14 F0286L653AAAA1 1 SPACER 10MM X 19MM X 27MM

COM 1 10-24X.2500 HX SOC SSCR15 F0045L682AAAA8 1 LEVER LINK

COM 2 10-24X1 HX SOC HD CSCR16 F0306L639AAAA6 2 MALE HOSE CONNECTOR .25X.125NPT

F0147S839AAAA9 1 AIR MUFFLER 1/8 NPT17 F0003S433AAAA2 1 SOCKET DIN MICRO HS-2

F0308L639AAAA4 1 PNEUMATIC VALVE 24VCOM 2 6-32X1 HX SOC HD CSCR

F0126L814AAAB3 2 MALE ELBOW 90DEG, 1/8 NPT X 1/4 T18 F0064L628AAAA1 1 NC NC FINGER PIVOT PIN

COM 1 M10 WSR (FLT)

19 F0001L482AAAA2 1 NC NC FINGERCOM 1 M8X1.25X25 HX SOC HD CSCRCOM 1 M8 WSR (FLT)

20 F0033H614AAAA4 120 TUBING .2500 OD


46/115


37


FIG. 10B SINGLE SEPARATOR


47/115




FIG. 10B SINGLE SEPARATOR


1 F0460L644AAAA1 1 DRIVE SHAFT

COM 1 .2500-28 HYDRAULIC FITTING STR2 F0283L653AAAA4 1 SHAFT COLLAR

COM 1 10 WSR (FLT)

COM 1 10-24X1 HX HD CSCR3 F0109L630AAAA4 1 DRIVE PULLEY P28T-5M-15

COM 1 10-24X.7500 HX SOC HD CSCR4 F0107L630AAAA6 1 TIMING BELT 475-5M-155 F0041L615AAAA4 2 AXIAL SEAL .625 D6 F0063L617AAAA5 1 BEARING HOLDER UPPER W/38L647 & 39L647 RING

F0038L647AAAA1 1 TOLERANCE RING

F0039L647AAAA0 1 TOLERANCE RING7 F0345L616AAAA6 2 BALL BEARING 17MM X 40MM X 12MM8 F0042L615AAAA3 3 AXIAL SEAL V-38

9 F0290L653AAAA5 1 NC NC FLAGCOM 1 8-32X1 HX SOC HD CSCR

COM 1 8-32 SQ NUT10 F0145L623AAAA9 1 GEAR HUB W/23L623 SEPARATOR DRIVEN GEAR

COM 1 .3125-18X.3750 HX SOC SSCR11 F0062L617AAAA6 1 BEARING HOLDER LOWER W/38L647 & 39L647 RING



12 F0033L417AAAA4 1 RETAINING RING

13 F0284L653AAAA3 3 SPACER 10MM X 16MM X 12MM14 F0044L615AAAA1 1 OIL SEAL 16MM X 24MM X 3MM15 F0344L616AAAA7 2 BALL BEARING 10MM X 22MM X 6MM16 F0110L630AAAA1 1 IDLER PULLEY 28T-5M-15


17 F0776L654AAAA7 1 GUARD POST

COM 1 .3750-16 HX NUT (JAM)

18 F0675L643AAAA3 1 BRACKET

COM 2 M10X1.5X70 HX SOC HD CSCR

19 F0285L653AAAA2 1 SPACER 10MM X 16MM X 48MM20 F0085L626AAAA8 1 SET SCREW MODIFIED .375-16 X 1.0 LG


COM 1 .1875 ROPE WICK21 F0086L626AAAA7 1 HEX HEAD SCREW MODIFIED .5-13 X 9.88 LG

COM 1 M12 WSR (FLT)22 F0108L630AAAA5 1 SEPARATOR PULLEY P28T-5M-15

COM 2 .2500-28X.3750 HX SOC SSCR (CUP/PT)23 F0348L616AAAA3 1 SHAFT WASHER 20MM X 35MM X 2MM24 F0347L616AAAA4 1 NEEDLE THRUST BEARING 20MM X 35MM X 2MM25 F0349L616AAAA2 1 HOUSING WASHER 21MM X 35MM X 2.75MM26 F0023L623AAAA6 1 SEPARATOR DRIVEN GEAR

COM 3 .4063X.8125X.1250 WSR

COM 3 .3750-16X1.7500 HX HD CSCR


48/115


39

60L DRIVE CASE 60LB007.08

FIG. 11A


49/115




FIG. 11A


1 F0011L653AAAA3 1 HANDWHEEL

2 F0017L644AAAA9 1 HANDWHEEL SHAFTCOM 1 6X2 TAPER PIN


3 F0005P253AAAB4 1 COLLAR 1.187

COM 1 .3750-16X.3750 HX SOC SSCR4 F0008L615AAAA5 1 OIL SEAL 1.187X1.69X.375W5 F0056L614AAAA7 1 DRIVE CASE SIGHT GLASS6 F0007L643AAAA2 1 DRIVE CASE



COM 1 .7500 PIPE PLUG (SOC HD)7 F0015L626AAAA3 REF MOTOR BASE SCREW BLOCK

8 F0014L654AAAB7 1 MOTOR BASE GUIDE COVER PLATE8 COM 2 .2500-20X.5000 HX HD CSCR9 F0012L643AAAA5 2 MOTOR BASE GUIDE


COM 8 .3750-16X1 HX SOC HD CSCR10 F0001L617AENP4 1 RETAINING RING - NICKEL PLATED

11 F0012L653AAAA2 1 CRANK HANDLE12 F0014L626AAAA4 1 MOTOR BASE SCREW

COM 1 .1875X1 SPRING PIN13 F0236L616AAAA8 1 MOTOR BASE SCREW BEARING .752X1.7005X.610

14 F0198L653AAAA8 2 COLLAR .7500X1X.3125

COM 2 .1875X1 SPRING PIN

15 F0000L654AAAA5 1 SERIAL NUMBER PLATE BLANK16 F0012H654AAAA0 1 SAFETY NAMEPLATE - CAUTION (ENGLISH)

COM 4 6X.3750 DR SCR (TYPE PK "U")17 F0009L623AAAA4 3 ELEVATOR WORM GEAR 30T 10P18 F0010L643AAAA7 1 DRIVE CASE CAP FEED SUPPORT


COM 1 .8750X1.1250X.7500 BUSHING


COM 1 .5000-14 NPT PIPE PLUG (HX SOC)


COM 1 .6250-11X2.5000 HX SOC HD CSCR19 F0008L623AAAA5 3 ELEVATOR WORM 2THD 10P

20 F0013L643AAAA4 2 ELEVATOR WORM BEARING BRACKETCOM 4 .3750-16X1.5000 HX SOC HD CSCR

21 F0018L644AAAA8 1 ELEVATOR WORM SHAFT - LONG

COM 3 608 (#13) WOODRUFF KEY22 F0002L617AENP3 7 RETAINING RING -NICKEL PLATED .750 SHAFT23 F0007L623AAAA6 2 ELEVATOR MITER GEAR 20T 10P


24 F0019L644AAAA7 1 ELEVATOR WORM SHAFT -SHORT

COM 1 608 (#13) WOODRUFF KEY


50/115


41


FIG. 11A


51/115



25 F0014L643AAAA3 1 ELEVATOR MITER GEAR BEARING BRACKET

COM 2 .3750-16X1.5000 HX HD CSCR

26 F0021L647AAAA0 1 ELEVATOR WORM SHAFT KEY

COM 1 .0938X.3125 SPRING PIN

27 F0656L643AAAA6 2 DRIVE CASE SUPPORT (DOOR)

COM 8 .3750 WSR (SHD)





COM 2 .8750X1.1250X.7500 BUSHING28 F0003L616AAAA9 3 BALL THRUST BEARING .875X1.890X.593W29 F0075L616AAAA2 3 ELEVATOR SCREW WASHER30 F0003L617AAAB1 3 RETAINING RING SS .8750 SHAFT31 F0011L623AAAA0 1 HANDWHEEL PINION 18T 8P32 F0012L626AAAB4 3 ELEVATOR SCREW


33 F0016L644AAAA0 3 DRIVE CASE SUPPORT SHAFT W/69L626 INSERT


COM 6 .5000-13X1.2500 HX HD CSCR

COM 6 .5000 WSR (LOCK)

F0069L626AAAA8 3 THREAD INSERT34 F0013L617AENP0 3 RETAINING RING -NICKEL PLATED 2.500 SHAFT D SS

35 F0558L643AAAA5 3 DRIVE CASE SUPPORT SHAFT CLAMP

COM 6 .5000-13X1.2500 HX HD CSCR

COM 6 .5000 WSR

COM 6 .5000 WSR (INT/SHPF)


52/115


43


FIG. 11B DOOR UNIT


53/115




FIG. 11B DOOR UNIT


1 L654 1 DOOR #3 (CAN SHOP)

2 F0009L626AAAA1 1 DOOR LATCH SCREW3 F0010L640AAAA0 1 DOOR LATCH SPRING

4 F0015L628AAAA1 1 DOOR LATCH PIN

5 F0059L628AAAA8 1 DOOR HINGE PIN UPPER

6 F0060L628AAAA5 1 DOOR HINGE PIN LOWER

1 F0738L654AAAA4 1 DOOR #3 (CANNERY)

2 F0009L626AAAA1 1 DOOR LATCH SCREW

3 F0010L640AAAA0 1 DOOR LATCH SPRING




7 L654 1 DOOR #1 (CAN SHOP)

2 F0009L626AAAA1 1 DOOR LATCH SCREW3 F0010L640AAAA0 1 DOOR LATCH SPRING




7 F0737L654AAAA5 1 DOOR #1 (CANNERY)

2 F0009L626AAAA1 1 DOOR LATCH SCREW





8 F0734L654AAAA8 1 DOOR #2 (CANNERY & CAN SHOP)

2 F0009L626AAAA1 2 DOOR LATCH SCREW5 F0058L628AAAA9 2 DOOR HINGE UPPER




9 F0236L653AAAA2 2 SEAMING DOOR COLLAR

COM 4 NYLON SHOULDER WASHER .3750


54/115


45

60L TOOLS AND WRENCHES 60LB010.03

FIG. 12


55/115



60L TOOLS AND WRENCHES 60LB010.03

FIG. 12

IND PART NO. QTY PART NAME1 F0042P216AAAA7 1 WIRE GAUGE HANDLE 1ST OPER .075"

F0042P216AAAA7 1 WIRE GAUGE HANDLE 2ND OPER .045"2 F0080L616AAAA5 1 CAP GUIDE RAIL WRENCH

3 F0081L616AAAA4 1 TURRET CLAMP WRENCH

4 F0082L616AAAA3 1 KNOCKOUT ROD BEARING PULLER

5 F0083L616AAAA2 1 LOWER CHUCK SPRING WRENCH

6 F0088L616AAAA7 1 LOWER CHUCK LOCK NUT WRENCH

7 F0091L616AAAA2 1 TURRET AND COLUMN CLAMP WRENCH

8 F0093L616AAAA0 1 GREASE GUN (HYDRAULIC FITTINGS)

9 F0362L616AAAA4 12 SHIM WASHER .003

F0362L616AAAB2 6 SHIM WASHER .005

F0362L616AAAC0 6 SHIM WASHER .010

10 F0052L816AAAA7 6 SHIM WASHER .003

F0052L816AAAB5 6 SHIM WASHER .005F1049L833AAAA8 1 DI-ELECTRIC GREASE COMPOUND 3.3OZ CONTAINER (NOT SHOWN)


56/115


47

60L MARKER 60LB012

FIG. 13 FOR CANNERY ONLY


57/115



60L MARKER 60LB012


IND PART NO. QTY PART NAME1 F0002L654AAAA3 1 MARKER DRIVE GUARD

COM 2 HEX HD CAPSCREW .3750-16X12 F0020L628AAAA4 1 HEX HD HINGE PIN HANDLE

3 F0032P616AAAA5 2 SET COLLAR 1” SHAFT

4 F0003L628AAAA5 2 MARKER HINGE PIN

5 F0174L616AAAA2 4 OILITE SLEEVE BUSHING 1X1.1875X.5000

6 F0203L653AAAA1 3 BEARING SPACER

7 F0035L615AAAA2 6 OIL SEAL 1.750X2.375X.375

8 F0272L616AAAA3 6 TAPERED ROLLER BEARING CONE

9 F0273L616AAAA2 6 TAPERED ROLLER BEARING CUP

10 F0201L653AAAA3 3 MARKER BEARING SPACER

11 F0274L616AAAA1 6 SHIM .001 THK

F0274L616AABA0 12 SHIM .002 THK

F0274L616AACA9 18 SHIM .005 THK12 F0036L815AAAA9 3 O-RING 1.2500X1.4375X.0938

13 F0204L653AAAA0 3 BEARING SPACER

14 F0024L623AAAA5 3 MARKER GEAR 39T 12P

15 F0045L616AAAA9 2 MARKER SHAFT WASHER .65X2X.31

16 F0031L616AAAA5 3 FLEXLOC NUT .6250-11 SS

17 F0278L654AAAA0 1 MARKER GEAR GUARD

18 F0024L628AAAA0 1 MARKER HINGE PIN RETAINER

19 F0019L640AAAA1 3 RETAINER SPRING

20 F0106L686AAAA0 1 MARKER BRACKET W/BUSHING

COM 2 GROOVE PIN .2500X1”

COM 1 HEX HD CAPSCREW .3750-16X1.2500

COM 4 HYDRAULIC FITTING .1250COM 3 MALE ELBOW .1875X.1250P BRS

COM 1 TUBING .1875 COPPER 20” LG

21 F0012P586AAAA5 1 MARKER BRAKE STUD

22 F0011P586AAAA6 1 MARKER BRAKE SHOE

COM 1 BRAKE LINING 1X.1875 WOVEN

COM 2 TUBULAR BRASS RIVET .1563X.5000

23 F0002P540AAAA2 1 BRAKE SPRING


COM 1 HEX SOC SET SCREW .2500-20X.3750

25 F0070L626AAAA5 6 HEX SOC SET SCREW .3750-24X.6875

26 F0082L686AAAA8 1 MARKER HANDWHEEL/BRAKE DRUM

COM 1 SPRING PIN .1875X.6250 SSCOM 1 CAPLUG 1.0625-12 PLASTIC

27 F0005L647AAAA0 1 KEY

28 F0004L623AAAA9 1 MARKER DRIVEN MITER GEAR 32T 8P

29 F0022P216AAAA1 1 THRUST WASHER 1.4678X2.4687X.1875

30 F0001L686AAAA6 1 MARKER DRIVE BEARING

31 F0006L644AAAA2 1 MARKER DRIVE SHAFT

32 F0042L686AAAA7 1 MARKER COUPLING

33 F0026L653AAAA6 1 MARKER COUPLING SLEEVE


58/115


49

60L MARKER 60LB012



59/115



COM 1 HEX HD CAPSCREW SLEEVE .2500-20X1.5000 SS

34 F0327L644AAAA4 1 MARKER DRIVEN SHAFT

COM 2 HEX SOC SET SCREW 10-24X.2500 SS

35 F0044L686AAAA5 1 MARKER LOWER SPINDLE ADJUSTMENT SCREW

36 F0028L686AAAA5 1 MARKER LOWER SPINDLE STUD

COM 1 HEX SOC SET SCREW 10-24X.2500

COM 1 PLUG .1250X.1250 BRS37 F0085L686AAAA5 1 MARKER UPPER SPINDLE DOWEL

38 F0026L686AAAA7 2 MARKER BLOCK

COM 4 LONG-LOK HEX SOC CAPSCREW .3750-16X1 SS

39 F0029L686AAAA4 2 MARKER TYPEHOLDER RETAINER

40 F0067L616AAAA2 2 TYPEHOLDER RETAINER BALL .2500 D SS

41 F0103L686AAAA3 2 MARKER SPINDLE (FOR ATMOSPHERIC)

COM 2 HEX SOC SET SCREW 10-24X.3750 SS

105L686 REF TYPEHOLDER SPINDLE

(STEAM VACUUM OR UNDER COVER GASSING)

COM REF HEX SOCKET SET SCREW 10-24X.3750 SS


60/115


51

60L DRIVE PARTS 60LB013.07

FIG. 14 W/ELECTRIC BRAKE


61/115





IND PART NO. QTY PART NAME1 F0325L653AAAA4 1 HANDWHEEL COLLAR

COM 1 TAPER PIN #6 X 22 F0008P926AAAA0 1 HANDWHEEL LATCH SCREW

3 F0720L643AAAA8 1 HANDWHEEL BRACKET

COM 1 HEX HD CAPSCREW .3750-16X1

COM 1 WASHER .4063X.8125X.1250

COM 1 HEX NUT .3750-16

COM 1 HEX SOC HD CAPSCREW 10-32X1

COM 2 HEX NUT 10-32

COM 2 WASHER #10

4 F0015P953AAAA7 1 HANDWHEEL LATCH BLOCK

COM 1 DOWEL PIN .2500X1.5000

5 F0663L833AAAJ7 1 LIMIT SWITCH 9’ CABLE

6 F0016P953AAAA6 1 HANDWHEEL LATCH HANDLE7 F0011L630AAAA1 1 CLUTCH HANDLE BALL

8 F0867L654AAAA7 1 DRIVE CASE COVER

COM 1 HEX SOC PIPE PLUG .5000-14 NPT


9 F0027L623AAAA2 1 DRIVE GEAR CLAMP RING

COM 6 HEX SOC HD CAPSCREW .3750-16X1.5000

10 F0041L814AAAB1 1 AIR VENT


12 F0034L416AAAA4 1 BEARING LOCKWASHER 30MM

13 F0001L623AAAB0 1 DRIVE BEVEL PINION 16T 5.500P W/GEAR

14 F0017L647AAAA6 1 KEY

15 F0009L617AAAA2 1 RETAINING RING 3.544 BORE16 F0010L616AAAA0 1 BALL BEARING 1.5748X3.5433X1.43

17 F0055L616AAAA6 1 DRIVE PINION WASHER

F0311L616AABA5 1 SHIM .003 THK

F0311L616AACA4 1 SHIM .005 THK

F0311L616AADA3 1 SHIM .010 THK

18 F0002L623AAAB0 1 DRIVEN BEVEL GEAR 48T 5.500P W/PINION

19 F0312L616AABA4 1 SHIM .003 THK

F0312L616AACA3 1 SHIM .005 THK

F0312L616AADA2 1 SHIM .010 THK

20 F0022L617AAAA5 1 DRIVE GEAR BEARING FLANGE


22 F0006L617AAAA5 1 RETAINING RING 2.750023 F0018L647AAAA5 1 KEY

24 F0026L623AAAA3 1 DRIVE GEAR HUB

25 F0716L643AAAA4 1 DRIVE BRACKET

COM 1 HEX NUT .3750-16


COM 3 HEX SOC HD CAPSCREW .6250-11X1.5000

COM 1 HEX HD CAPSCREW .6250-18X.6250

26 F0029L615AAAA0 1 O-RING 4.50X4.750X.125


62/115


53




63/115



27 F0001L615AAAA2 1 OIL SEAL 1.875X3X.50

28 F0010L623AAAA1 1 HANDWHEEL GEAR 45T 8P


30 F0022H617AAAA4 1 SNAP RING-BEVELED 1.772

31 F0002H615AAAA0 1 OIL SEAL 1.6875X2.839X.469

32 F0717L643AAAA3 1 BRACKET ELECTRIC BRAKE

COM 4 HEX SOC HD CAPSCREW .3750-16X133 F0043L433AAAB0 1 ELECTRIC BRAKE

34 F0027L647AAAA4 1 KEY .3750 SQ X 1.2500

35 F0016L647AAAA7 1 KEY .3750 SQ X 3.375

36 F0496L644AAAA9 1 DRIVE SHAFT


64/115


55

60L SUPPLEMENTAL PARTS 60LB019.02

FIG. 15 CAN SHOP


65/115




FIG. 15 CAN SHOP

IND PART NO. QTY PART NAME1 F0002L617AENP3 6 RETAINING RING .750 SHAFT

2 F0137L644AAAA4 6 KNOCKOUT ROD END BOTTOM3 F0030L644AAAA2 6 KNOCKOUT ROD END

4 F0044L628AAAA6 6 KNOCKOUT ROD PIN

5 F0015L640AAAA5 6 KNOCKOUT ROD CUSHION SPRING

6 F0500L644AAAA2 6 KNOCKOUT ROD

7 F0025L841AAAA0 6 KNOCKOUT PAD

8 F0372L616AAAA2 6 RETAINING WASHER

9 F0063L826AAAA2 6 HEX SOCKET FLAT HD CAP SCREW

10 F0007L826AAAA1 6 LOWER CHUCK PLATE SCREW

11 F0371L616AAAE7 6 SHIM WASHER .105 THK


66/115


57


FIG. 16 CANNERY


67/115




FIG. 16 CANNERY

IND PART NO. QTY PART NAME1 F0002L617AENP3 6 RETAINING RING .750 SHART

2 F0137L644AAAA4 6 KNOCKOUT ROD END BUTTON3 F0030L644AAAA2 6 KNOCKOUT ROD END

4 F0044L628AAAA6 6 KNOCKOUT ROD PIN

5 F0015L640AAAA5 6 KNOCKOUT ROD CUSHION SPRING

6 F0427L644AAAA3 6 KNOCKOUT ROD

7 F0025L841AAAA0 6 KNOCKOUT PAD

8 F0372L616AAAA2 6 RETAINING WASHER

9 F0063L826AAAA2 6 HEX SOCKET FLAT HD CAP SCREW


68/115


59

60L CHANGE PARTS 60LC

FIG. 17 CANNERY ATMOSPHERIC


69/115



60L CHANGE PARTS 60LC

FIG. 17 CANNERY ATMOSPHERIC


L608 10 SEAMING & DISCHARGE STAR LINER

L636 6 SEAMING CHUCKL639 1 CAP GUIDE RAIL-OUTER

L642 1 SEAMING CHUCK BELL

L642 6 CHUCK BELL COVER GUIDE

L645 1 DISCHARGE UPPER RAIL

L633 8 CAP PUSH BOOSTER MAGNET

L659 8 CAP PUSHER

L669 1 COVER TRIP GUARD RAIL

L670 8 CAP FEED TURRET LINER

L672 1 CAP GUIDE INNER

L672 1 CAP GUIDE RAIL INNER

L672 1 CAP GUIDE SECTION OUTER

L683 1 CAN FEED & DISCHARGE RAILL684 1 CAN FEED INLET RAIL

L856 1 SEPARATOR DISC/KNIFE

L656 1 DISCHARGE RAIL SHAFT BRACKET

L685 1 CAP MAGAZINE


70/115


61

60L CHANGE PARTS 60LMC

FIG. 18 CAN SHOP


71/115



60L CHANGE PARTS 60LMC

FIG. 18 CAN SHOP



L636 6 SEAMING CHUCKL637 6 LOWER CHUCK FLANGED PLATE

L626 18 CONE POINT SET SCREW CAN SHOP

L642 1 SEAMING CHUCK BELL



L659 8 CAP PUSHER

L670 8 CAP FEED TURRET LINER


L672 1 CAP GUIDE RAIL OUTER


L683 1 CAN FEED OUTER RAIL

L683 1 CAN FEED UPPER RAILL683 1 CAN FEED & DISCHARGE RAIL

L653 1 CAN FEED UPPER RAIL SPACER


L690 1 CAN FEED STAR


L690 1 TIMING WORM

L685 1 CAP MAGAZINE


72/115


63

60L CHANGE PARTS 60LSC

FIG. 19 STEAM VACUUM


73/115



60L CHANGE PARTS 60LSC

FIG. 19 STEAM VACUUM



L636 6 SEAMING CHUCKL642 1 SEAMING CHUCK BELL



L656 1 CAP GUIDE DRAG WIRE


L659 8 CAP PUSHER

L670 1 CAP FEED TURRET

L670 1 CAP FEED TURRET PLATE


L639 1 CAP GUIDE RAIL OUTER


L672 1 CAP GUIDE INNERL683 1 CAN FEED & DISCHARGE RAIL

L684 1 CAN FEED INLET RAIL


L670 8 CAP FEED TURRET INSERT - LONG

L670 8 CAP FEED TURRET INSERT- SHORT

L669 1 COVER TRIP GUIDE RAIL


74/115


65

60L CAN FEED EXTENSION 60LD001

FIG. 20 CANNERY


75/115




FIG. 20 CANNERY


1 F0016L669AAAA0 1 TAKE-UP CHAIN SUPPORT

COM 4 .2500-20X.5000 FLT HD MSCRCOM 2 .2500-20X.7500 FLT HD MSCR



2 F0022L644AAAA2 1 TAKE-UP SPROCKET SHAFT


3 F0005L624AAAA7 1 FEED TAKE-UP SPROCKET 24T .7500P

4 F0019L643AAAA8 1 TAKE-UP BRACKET

COM 1 .6250-11X6.000 SQ HD SSCR (F/THRD)

5 F0018L643AAAA9 1 TAKE-UP SPROCKET BRACKET


COM 1 .1250X4 BLACK NIPPLE

COM 2 .6250-11X1.7500 HX HD CSCRCOM 2 .6250 WSR


COM 1 .1250-27 PIPE CPLNG

6 F0005P253AAAB4 1 COLLAR 1.187


7 F0016P681AAAA5 1 FEED TABLE ELEVATOR SHAFT BRACKET


8 F0023L644AAAA1 1 CAN FEED EXTENTION TABLE SUPPORT SHAFT

COM 1 6X2 TAPER PIN

9 F0014P681AAAA7 1 FEED TABLE ELEVATOR PEDESTAL


10 F0018L654AAAA5 1 CAN FEED EXTENSION TAKE-UP GUARDCOM 2 .3750-16X2 HX HD CSCR

11 F0002L624AAAA0 30 CAN FEED CHAIN FINGER .7500P

COM 60 .0625X.3750 COTTER PIN

F0002L624AAAD4 60 PIN

F0002L624AAAE1 60 COTTER PIN12 F0001L624AAAA1 30 CAN FEED CHAIN SECTION .7500P 5.2500 LG13 F0015L669AAAA1 1 CAN FEED EXTENSION CAN GUIDE

COM 2 .5000-13X2.5000 HX HD CSCR

COM 2 .5313X1.2500X.1250 WSR (SAE)14 F0009L669AAAA9 1 CAN FEED EXTENSION GUIDE CHAIN RAIL


15 F0061L669AAAA4 1 FEED CHAIN WEAR STRIP -FILLER ENDCOM 3 10-24X.6250 FLT HD MSCR

16 F0011L669AAAA5 1 FEED TABLE WEAR PLATE -FILLER END

COM 3 .2500-20X.6250 FLT HD MSCR17 F0014L669AAAA2 1 FEED TABLE FILLER STRIP -NARROW18 F0017L669AAAA9 1 FEED CHAIN COVER RAIL -FILLER END

COM 3 .3750-16X2.2500 HX HD CSCR19 F0013L669AAAA3 1 FEED TABLE FILLER STRIP -WIDE

20 F0060L669AAAA5 1 FEED CHAIN WEAR STRIP -SEAMER END


76/115


67


FIG. 20 CANNERY


77/115



COM 6 10-24X.6250 FLT HD MSCR21 F0012L669AAAA4 1 FEED TABLE WEAR PLATE -SEAMER END

COM 5 .2500-20X.6250 FLT HD MSCR22 F0008L669AAAA0 1 FEED CHAIN COVER RAIL -SEAMER END

COM 5 .3750-16X2.2500 HX HD CSCR23 F0017L643AAAA0 1 CAN FEED EXTENSION TABLE 48-.5000"

COM 7 .5000-13 HX NUT

COM 7 .5000 WSR

COM 7 .5000-13X2 FLT HD MSCR

24 F0002L614AAAA2 1 CHAIN LUBRICATOR

(F0002L614AAAB0) 1 GRAVITY FEED OILER

COM 1 .2500 NPT PIPE LOCK NUT

COM 1 .2500 PIPE (CONT THRD)

COM 2 .2500 ELBOW (90 DEG)

COM 1 .1250 WIRE CORED WICKING


COM 1 .2500X1.5000 NPT PIPE (END UNTHR'D)

COM 1 .2500X2.5000 NPT PIPE (UNTHR'D)

25 F0017L654AAAA6 1 FEED CHAIN RETURN GUARD

COM 3 .2500-20X.5000 RD HD MSCR

COM 1 .2500-20X.7500 RD HD MSCR

COM 1 .2500-20 HX NUT


78/115


69


FIG. 20 CANNERY


79/115




FIG. 20 CANNERY

48.50 LG

TABLE

60.50 LG

TABLE

72.50 LG

TABLE

90.50 LG

TABLE

IND CHANGE PARTSDESCRIPTION

QTY PARTS NO. QTY PARTS NO. QTY PARTS NO. QTY PARTS NO.

23 FEED TABLE 1 17L643 1 27L643 1 40L643 1 81L643

25FEED CHAIN RETURN

GUARD1 17L654 1 27L654 1 37L654 1 71L654

16FEED TABLE WEAR

PLATE FILLER END1 11L669 1 28L669 1 28L669 1 28L669

FEED TABLE WEAR

PLATE INSERT 12"1 71L669

FEED TABLE WEAR

PLATE INSERT 30"1 190L669

18FEED CHAIN COVER

RAIL FILLER END1 17L669 1 31L669 1 17L669 1 69L669

FEED CHAIN COVER

RAIL MIDDLE 24"1 69L669

FEED CHAIN COVER

RAIL MIDDLE 36"1 185L669

15FEED CHAIN WEAR

STRIP FILLER END1 61L669 1 62L669 1 61L669 1 186L669

FEED CHAIN WEAR

STRIP MIDDLE 24"1 70L669 1 70L669

14FEED CHAIN GUIDE

RAIL FILLER END

1 9L669 1 26L669 1 66L669 1 187L669

19FEED TABLE FILLER

STRIP, WIDE1 13L669 1 29L669 1 67L669 1 188L669

17FEED TABLE FILLER

STRIP, NARROW1 14L669 1 30L669 1 68L669 1 189L669

1TAKE-UP CHAIN

SUPPORT1 16L669 1 32L669 1 73L669 1 199L669

TAKE-UP CHAIN

SUPPORT BRACKET1 422L669 1 422L669


80/115


71

60L 16” WORM CAN FEED EXTENSION 60LD128.03

FIG. 21 CAN SHOP


81/115




FIG. 21 CAN SHOP

IND PART NO. QTY PART NAME1 F0166L653AAAA6 1 SPACER .4062X1X.1875

2 F0272L654AAAA6 1 WORM GUARDCOM 3 .3750-16X.5000 HX HD CSCR3 F0107L644AAAA0 1 WORM SHAFT -SHORT4 (F0051P416AAAA3) 3 SLEEVE BUSHING .6250X.7500X1.5000 BRZ5 F0250L616AAAA9 3 WORM BEARING BLOCK6 F0163L653AAAA9 3 SPACER7 F0162L653AAAA0 3 WORM BEARING BLOCK SPACER8 F0518L643AAAA4 2 HOLDDOWN BAR SUPPORT

COM 4 .2500 WSR (FLT)COM 2 .2500-20X.7500 HX HD CSCRCOM 2 .2500-20X2.2500 HX HD CSCR

9 F0213L653AAAA9 2 SPACER10 F0517L643AAAA5 2 HOLDDOWN SUPPORT BRACKET


11 L690 1 TIMING WORMS12 F0301L671AAAA0 1 HOLD DOWN BAR13 F0248L653AAAA8 2 SPACER .2813X.6250X.750014 F0001L633AAAA0 1 SOLENOID 115V15 F0040P454AAAA0 1 CAN STOP HOUSING COVER

COM 4 .2500-20X.5000 HX HD CSCR16 F0017L628AAAA9 1 SOLENOID LINK PIN17 F0003P446AAAA6 1 CAN STOP SOLENOID LEVER

COM 1 .1875X1 DOWEL PIN18 F0010P440AAAA3 1 CAN STOP FINGER SPRING19 F0009L653AAAA7 2 CAP FEED SET COLLAR .5000 SHAFT20 F0049L646AAAA9 1 CAN STOP FINGER SHAFT


21 F0006P440AAAA9 1 SOLENOID LEVER SPRING22 F0033P416AAAA6 2 RULON INSERT BEARING .5000 X .6250 X .500023 F0015L633AAAA4 1 MICRO SWITCH24 F0001P446AAAA8 1 CAN FEED STOP HOUSING

COM 1 .1875X.7500 DOWEL PINCOM 2 .3750-16X1 HX HD CSCRCOM 1 .2500-20 HX NUT (JAM)COM 1 .2500-20X.3750 HX SOC HD CSCRCOM 1 .1875X.1250 PLUGCOM 1 .2500-20 HX NUT (JAM)COM 4 8-32X.2500 RD HD MSCRCOM 4 .3750 PLUG

25 F0901L833AAAO8 36 CABLE -3COND 18AWG OLFLEX

26 F0060L833AAAA6 1 SEALING O-RING W/RETAINER .5000"27 F0096L654AAAA0 1 BACKING PLATE BRACKET28 F0067L671AAAA4 1 WORM CAN FEED PLATE

COM 1 .3750-16X.6250 HX HD CSCRCOM 3 .5000-13X1.7500 HX HD CSCRCOM 3 .3750-16X1.5000 HX HD CSCRCOM 2 .5000-13X1.7500 HX SOC FLT HD MSCRCOM 5 .5000-13 HX NUTCOM 3 .4063X.8125X.0625 WSR

29 F0285L644AAAA4 1 WORM SHAFT -LONG


82/115


73


FIG. 21 CAN SHOP


83/115



30 F0362L654AAAA7 1 BACKING PLATE COVERCOM 1 .3750-16X.5000 HX HD CSCR

31 F0034L624AAAA2 1 WORM DRIVEN SPROCKET 15T .500032 F0019L624AAAA1 1 IDLER SPROCKET .5000P 18T33 F0286L644AAAA3 1 WORM DRIVE SHAFT

COM 1 .1250 NPTF HYDRAULIC FIT34 F0357L654AAAA4 1 CHAIN GUARD

COM 2 .3750-16X2.2500 HX HD CSCRCOM 2 .4063X.8125X.0625 WSR

35 F0165L653AAAA7 2 SPACER36 F0032L624AAAA4 1 ROLLER CHAIN .5000P37 F0033L624AAAA3 1 WORM DRIVE SPROCKET38 F0029L617AAAA8 1 RETAINING RING 2" SHAFT39 F0356L654AAAA5 1 CHAIN GUARD BACK W/68L826

(F0068L826AAAA7) 2 SELF-CLINCHING NUTCOM 2 .3750-16X.6250 FLT HD MSCR

40 F0136L616AAAA9 1 DRIVE SHAFT BEARING BLOCKCOM 2 1X1.2500X2 BUSHINGCOM 2 .2500X1 DOWEL PINCOM 2 .3750-16X3 HX HD CSCR

41 F0096L616AAAA7 1 THRUST WASHER 1"ID X 2"OD X .1250T42 F0068L623AAAA2 1 PINION 24T 10P

COM 1 5X2 TAPER PIN43 F0002P446AAAA7 1 CAN STOP FINGER

COM 1 .2500-20X1 HX HD CSCR44 F0137L616AAAA8 2 THRUST WASHER .640X1.125X.12545 F0164L653AAAA8 2 SPACER .4375X1X.468846 F0042L653AAAA6 2 TRANSFER RAIL SPACER OUTER .4375X1X.8125 LG47 F0302L669AAAA3 2 CAN FEED EXTENSION RAIL

COM 4 .3750-16X4 HX HD CSCRCOM 4 .3750-16 HX NUTCOM 8 .4063X.8125X.0625 WSR

48 F0080L653AAAA9 2 EXTENSION RAIL SPACER .4375X1X1 LG

49 F0067L623AAAA3 1 BEVEL GEAR 120T 10PCOM 5 .3750-16X1.2500 HX HD CSCR

50 F0045P616AAAB8 1 SPACER FOR INLET RAIL EXTENSION51 F0068L671AAAA3 1 WEAR STRIP

COM 1 .2500-20 HX NUTCOM 3 .2500-20X.7500 FLT HD MSCR

52 F0839L669AAAA5 1 WORM EXTENSION RAILCOM 2 .3750-16X3.5000 HX HD CSCRCOM 2 .3750-16 HX NUTCOM 2 .4063X.8125X.0625 WSR

53 F0011L853AAAA1 4 SPACER .4062X1X1.12554 F0134S833AAAB8 2 CORD CONNECTOR .5000 STR.125-.375 RANGE55 F0018L833AAAC5 1 SEALING FITTING .5000"

F0028L614AAAA2 4 TUBE FITTING (NOT SHOWN)F0030L614AAAA8 4 TUBE FITTING .125T STRAIGHT (NOT SHOWN)F0032L614AAAA6 81 NYLON TUBING .1250XLG (NOT SHOWN)F0108L614AAAA5 1 LUBRICATION BLOCK (NOT SHOWN)


84/115


75

60L FILLER DRIVE 60LD004.01

FIG. 22


85/115



60L FILLER DRIVE 60LD004.01

FIG. 22

IND PART NO. QTY PART NAME1 F0022P216AAAA1 1 THRUST WASHER

2 F0022L647AAAA9 1 FILLER DRIVE KEY .375 X.375 X 1.88 LG3 F0036L616AAAA0 3 CLUTCH BALL BUSHING .627X.875X.3754 F0005L697AAAA9 1 FILLER DRIVE CLUTCH SPRING HUB PLATE5 F0314L616AAAA3 1 FILLER DRIVE CLUTCH HUB BUSHING6 F0004L697AAAA0 1 FILLER DRIVE CLUTCH SPRING HUB

COM 1 10-24X.5000 HX SOC HD CSCRCOM 1 .3750-16X.7500 HX SOC SSCRCOM 1 709 (17) WOODRUFF KEYCOM 1 .1250X.5000 GRV PIN

7 F0007L697AAAA7 1 FILLER DRIVE CLUTCH HOUSING8 F0008L697AAAA6 1 FILLER DRIVE CLUTCH HOUSING PLATE9 F0009L697AAAA5 1 FILLER DRIVE CLUTCH BALL HUB

COM 1 10-24X.5000 HX SOC HD CSCRCOM 1 .3750-16X.7500 HX SOC SSCR

10 F0048L616AAAA6 3 STEEL BALL (HARDENED) .62 D11 F0022L647AAAA9 1 FILLER DRIVE KEY .375 X.375 X 1.88 LG12 F0055L628AAAA2 3 FILLER DRIVE CLUTCH HUB PIN13 F0022L647AAAA9 1 FILLER DRIVE KEY .375 X.375 X 1.88 LG14 F0028L623AAAA1 1 FILLER DRIVE GEAR

COM 6 .5000-13X1.5000 HX SOC HD CSCR15 F0014L640AAAA6 5 FILLER DRIVE CLUTCH SPRING16 F0006L697AAAA8 1 FILLER DRIVE CLUTCH SPRING RETAINER

COM 1 .3750-16X.8750 HX SOC HD CSCRCOM 1 .2500-28 45 DEG HYD FIT

17 F0029L623AAAA0 1 FILLER DRIVE PINIONCOM 1 .3750-16X.7500 HX SOC SSCRCOM 1 10-24X.5000 HX SOC HD CSCR

COM 1 .3125X2.5000 SPRING PIN18 F0022P216AAAA1 1 THRUST WASHER19 F0026L644AAAA8 1 FILLER DRIVE SHAFT20 F0020L643AAAA5 1 FILLER DRIVE BRACKET

COM 2 1.4375X1.7500X2 BUSHING #1 GRVCOM 1 1.4375X1.7500X3 BUSHING #1 GRVCOM 2 .5000-13X3.500 HX HD CSCRCOM 4 .5000-13X1.7500 HX HD CSCRCOM 2 .1250-27 65 DEG HYDRAULIC FITTINGCOM 1 .1875X1.2500 GRV PINCOM 2 .1875TX.1250P MALE ELBOWCOM 36 .1875 OD TUBINGCOM 2 .1875TX.1250P MALE CONN

21 F0051L626AAAA8 2 LOWER CHUCK SPRING ADJUSTMENT SCREW22 F0025L644AAAA9 1 FILLER INTERMEDIATE DRIVE SHAFT23 F0022P216AAAA1 1 THRUST WASHER24 F0018L653AAAA6 1 FILLER DRIVE SHAFT COLLAR

COM 1 .3750-16X.7500 HX SOC SSCR25 F0549L654AAAA3 1 GUARD FOR BASE GEARING

COM 6 .2500-20X.5000 HX HD CSCR


86/115


77

60L AUTOMATIC STOP 60LD006.04

FIG. 23A CANNERY


87/115




FIG. 23A CANNERY


CLUTCH RELEASE UNIT1 F0001L633AAAA0 1 SOLENOID 115V2 F0089L833AAAA3 1 SINGLE CONDUCTOR #16 STRDD THHN3 F0018L633AAAC5 1 SEALTITE FLEXIBLE .5000"4 F0004L646AAAA2 1 CLUTCH LINK ROD COLLAR5 F0007L646AAAA9 1 SOLENOID LINK6 F0017L628AAAA9 2 SOLENOID LINK PIN7 F0006L646AAAA0 1 SOLENOID TRIP8 F0022L633AAAA5 REF SEALTITE FITTING .50X90 DEG9 F0012L640AAAA8 1 SOLENOID TRIP SPRING

10 F0004L640AAAA8 1 SPRING11 F0002L646AAAA4 1 CLUTCH LINK

12 F0009L626AAAA1 1 DOOR LATCH SCREW (SS)13 F0005L646AAAA1 1 CLUTCH LINK LATCH14 F0009L640AAAA3 1 CLUTCH LINK SPRING

CONTROL BOX UNIT (REF ONLY)15 F0005L633AAAA6 1 CONTROL BOX SWITCH PLATE16 F0195L833AAAA4 1 SELECTOR SWITCH -3POS -STD BLK KNOB17 F0061L633AAAA7 1 SELECTOR PUSH BUTTON START JOB18 F0211L833AAAA4 1 PUSH BUTTON OPERATOR -MUSHROOM

F0133L833AAAA9 5 CONTACT BLOCK

F0150L833AAAF6 1 LEGEND PLATE -STOP

F0150L833AAAJ7 1 LEGEND PLATE -HAND OFF AUTOF0150L833AAAG4 1 LEGEND PLATE -START JOG

TERMINAL BOX & CAN FEED CONVEYOR UNIT

19 F0016L646AAAA8 1 TERMINAL BOX GASKET

20 F0014L646AAAA0 1 SWITCH SPRING LEVER


22 F0015L633AAAA4 1 MICRO SWITCH

23 F0004L633AAAA7 1 TERMINAL BLOCK

24 F0006L633AAAA5 REF CORD GRIP .5000 STR

25 F0007L633AAAA4 66 FLEXIBLE CORD SO #14-2 TYPE 2X LG


27 F0013L646AAAA1 1 SWITCH LEVER28 F0018L633AAAA1 66 SEALTITE FLEXIBLE CONDUIT .5000" X LG___

29 F0019L633AAAA0 2 SEALTITE FITTING .5000 STR

30 F0015L646AAAA9 1 TERMINAL BOX


88/115


79


FIG. 23B CANNERY


89/115




FIG. 23B CANNERY


CAN DISCHARGE UNIT (REF ONLY)1 F0107L633AAAA3 1 LIMIT SWITCH


LOW CAP STACK UNIT

10 F0008L633AAAA3 1 LIMIT SWITCH

11 F0010L646AAAA4 1 SWITCH ARM

12 F0022L633AAAA5 2 SEALTITE FITTING .50X90 DEG

13 F0009L646AAAA7 1 SWITCH BRACKET

14 F0018L633AAAA1 240 SEALTITE FLEXIBLE CONDUIT .5000" X LG___

15 F0089L833AAAA3 2 SINGLE CONDUCTOR #16 STRDD THHN

FILLER DRIVE UNIT16 F0015L633AAAA4 1 MICRO SWITCH

17 F0017L646AAAA7 1 FILLER DRIVE BRACKET SWITCH BOX

18 F0018L646AAAA6 1 SWITCH BOX GASKET


20 F0013L646AAAA1 1 SWITCH LEVER

21 F0040L644AAAA0 1 SWITCH LEVEL SHAFT


23 F0014L646AAAA0 1 SWITCH SPRING LEVER

24 F0006L633AAAA5 REF CORD GRIP .5000 STR


PARTS ARE NOT SHOWNF0134S833AAAC6 CORD CONNECTOR .310-.560 RANGE STR .5000


90/115


81


FIG. 24A CAN SHOP


91/115




FIG. 24A CAN SHOP


CLUTCH RELEASE UNIT1 F0001L633AAAA0 1 SOLENOID 115V2 F0089L833AAAA3 2 SINGLE CONDUCTOR #16 STRDD THHN3 F0018L633AAAA1 39 SEALTITE FLEXIBLE CONDUIT .5000" X LG___4 F0004L646AAAA2 1 CLUTCH LINK ROD COLLAR5 F0007L646AAAA9 1 SOLENOID LINK6 F0017L628AAAA9 2 SOLENOID LINK PIN7 F0006L646AAAA0 1 SOLENOID TRIP8 F0022L633AAAA5 2 SEALTITE FITTING .50X90 DEG9 F0012L640AAAA8 1 SOLENOID TRIP SPRING

10 F0004L640AAAA8 1 SPRING11 F0002L646AAAA4 1 CLUTCH LINK

12 F0009L626AAAA1 1 DOOR LATCH SCREW (SS)13 F0005L646AAAA1 1 CLUTCH

Documents

60l Manual Actualizado