APV-4RH, DPV-4RH

8/8/2019 APV-4RH, DPV-4RH

1/13

Video DoorPhoneM od el No. DPV-4RH/ APV-4RH


2/13

- 1 -

Introduction

WARNING

To prevent f ire or shock hazard, do not

ex pose the unit to ra in or m oisture.

INFORMATION

This equipment generates and uses radio frequencyenergy and if not installed and used properly; that is,

in strict accordance with the manufacturers

instructions, may cause interference to radio and

television reception. It has been type tested and

found to comply with the limitations for a Class B

computing device in accordance with the

specifications in Subpart J of Part 15 of the FCC

Rules, which are designed to provide reasonable

protection against such interference in a residentialinstallation. However, there is no guarantee that

interference will not occur in a particular installation.

If this equipment does cause interference to radio or

television reception, which can be determined by

turning the equipment off and on, the user is

encouraged to try to correct the interference by one

or more of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and

receiver.

- Connect the equipment to an outlet of a circuit

different from that to which the receiver is

connected.

- Consult the dealer or on experienced radio/ TV

technicion for help.

This symbol is intended to alert the

user to the presence of uninsulated

dangerous vo l tage within the

products enclosure that may be of

sufficient magnitude to constitute a

risk of electric shock to persons.

This symbol is intended to alert the

user to the presence of important

operating and maintenance

(servicing) instructions in the

literature accompanying the unit.

CAU TIO N : TO REDUCE THE RISK O F ELECTRIC

SHOCK, DO NOT REMOVE COVER (OR BACK). NO

USER-SERVICEABLE PARTS INSIDE. REFER

SERVICING TO Q UA LIFIED SERVICE PERSON N EL.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

TO PREVEN T ELECTRIC SHO CK, DO N OT

USE TH IS PO LA RIZ ED A C PLUG W ITH

AN EXTEN SION CORD, RECEPTACLE OR

O TH ER OUTLET, UN LESS THE BLADES

CAN BE FULLY IN SERTED TO PREVEN T

BLADE EXPOSURE.


3/13

- 2 -

Imp or tan t Saf ety Instructions

1. R e a d I n s t r u c t i o n s - All the safety and

operating instructions should be read before theproduct is operated.

2. Retain Instruction s - The safety and operatinginstructions should be retained for futurereference.

3. Heed War nings - All warnings on the productand in the operating instructions should beadhered to.

4. Fol low Instructions - All operating and useinstructions should be followed.

5. C l e a n i n g - Unplug this product from the walloutlet before cleaning. Do not use liquid cleanersor aerosol. Use a damp cloth for cleaning.

6. A t t a c h m e n t s - Do not use attachments not

recommended by the product manufacturer, asthey may cause hazards.

7. W a t er a n d M o ist u r e - Do not use thisproduct near water - for example, near a bathtub, wash bowl, kitchen sink, laundry tub, in awet basement, near a swimming pool, and thelike.

8. Accessories - Do not place this product on anunstable cart, stand, tripod bracket, or table. Theproduct may fail, causing serious injury to a childor adult, and serious damage to the product. Useonly with a cart, stand, tripod, bracket, or tablerecommended by the manufacturer, or sold withthe product. Any mounting of the product shouldfollow the manufacturers instructions, and shoulduse a mounting accessory recommended by the

manufacturer.

9. A prod uct and cart

combination should bemoved with care. Quickstops, excessive force, anduneven surfaces maycause the product andcart combination to overturn.

10. V e n t i l a t i o n - Slots and openings in thecabinet are provided for ventilation and toensure reliable operation of the product.They protect it from overheating, and theseopenings must not be blocked or covered. Theopenings should never be blocked by placing theproduct on a bed, sofa, rug, or other similarsurface. This product should not be placed in abuilt-in installation such as a bookcase or rackunless proper ventilation is provided, or themanufacturers instructions have been adhered to.

11. Pow er Sou r ces - This product should beoperated only from the type of power sourceindicated on the marking label. If you are notsure of the type of power supply in your home,consult your product dealer or local powercompany. For products intended for operationfrom battery power or other sources, refer to theoperating instructions.

12. Grounding or Polarizat ion - This productmay be equipped with a polarized alternating-current line plug (a plug having one blade widerthan the other). This plug will fit into the poweroutlet only one way. This is a safety feature. Ifyou are unable to insert the plug fully into theoutlet, try reversing the plug. If the plug stillcannot be inserted, contact your electrician toreplace your obsolete outlet. Do not defeat the

safety purpose of the polarized plug.


4/13

- 3 -

Imp or tan t Saf ety Instructions

13. Pow er -Car d Pro tect i on - Power-supply

cords should be routed so that they are not likelyto be walked on or pinched by items placedupon or against them paying particular attentionto cords at plugs, convenience receptacles, andthe point where they exit from the product.

14. Protective Attachment Plug - The productis equipped with on attachment plug havingoverload protection. This is a safety feature. Seeinstruction Manual for replacement of, orresetting the protective device. If replacement ofthe plug is required, be sure the servicetechnician has uses a replacement plug specifiedby the manufacturer that has the same overloadprotection as the original plug.

15. O u t d o o r A n t en n a Gr o u n d i n g - If anoutside antenna or cable system is connected tothe product, be sure the antenna or cable system

is grounded so as to provide some protectionagainst voltage surges and built-up staticcharges. Article 810 of the National ElectricalCode, ANSI/ NFPA 70, provides informationwith regard to proper grounding of the mastand supporting structure, grounding of the lead-in wire to an antenna discharge unit, size ofgrounding conductors, location of antenna-discharge unit, connection to grounding

electrodes, and requirements for the groundingelectrode (Refer to the figure on page 5 ).

16. L i g h t n i n g - For added protection of thisproduct during a lightning storm, or when it isleft unattended and unused for long periods oftime, unplug it from the wall outlet anddisconnect the antenna or cable system. This willprevent damage to the product due to lightning

and power-line surges.

17. Pow er Lines - An outside antenna system

should not be located in the vicinity of overheadpower lines or other electric light or powercircuits, or where it can fall into such powerlines or circuits.

When installing on outside antenna system,extreme care should be taken to keep fromtouching such power lines or circuits as contactwith them might be fatal.

18. Ove r lo ad in g - Do not overload wall outlets,extension cords, or integral conveniencereceptacles, as this can result in a risk of fire orelectric shock.

19. Objec t and L iqu id Ent ry - Never pushobjects of any kind into this product throughopenings as they may touch dangerous voltagepoints or short-out parts that could result in a

fire or electric shock. Never spill liquid of anykind on the product.

20. S e r v i c i n g - Do not attempt to service thisproduct yourself as opening or removing coversmy expose you to dangerous voltage or otherhazards. Refer all servicing to qualified servicepersonnel.

21. Damage Requiring Service - Unplug thisproduct from the wall outlet and refer servicingto qualified service personnel under thefollowing conditions.

A. When the power-supply cord or plug isdamaged.

B. If liquid has been spilled, or objects havefallen into the product.

C. If the product has been exposed to rain orwater.


5/13

- 4 -

D. If the product does not operate normally by

following the operating instructions. Adjustonly those controls that are covered by theoperating instructions, as an improperadjustment of other controls may result indamage and will often require extensivework by a qualified technician to restore theproduct to its normal operation.

E. If the product has been dropped or damagedin any way.

F. When the product exhibits a distinct changein performance - this indicates a need orservice.

22. Replacement Parts - When replacementparts are required, be sure the servicetechnician has used replacement parts specifiedby the manufacturer or have the samecharacteristics as the original part.Unauthorized substitutions may result in fire,electric shock or other hazards.

23. Safety Check - Upon completion of any

service or repairs to this product, ask the servicetechnician to perform safety checks to determinethat the product is in proper operatingcondition.

24. Wal l or Cei l ing Mount ing - The productshould be mounted to a wall or ceiling only asrecommended by the manufacturer.

25. Heat - The product should be situated away

from heat sources such as radiators, heatresistors, or other products (including amplifiers)that produce heat.

Imp or tant Saf ety Instructions


6/13

- 5 -

Table of Contents

Introduction ............................................................................................................................ 1

Important Safety Instructions ..................................................................................................... 2

Table of Contents .................................................................................................................... 5

1. Features ............................................................................................................................5

2. Parts Checklist and Functions................................................................................................6

3. Installation Instructions.........................................................................................................7

4. Operation ..........................................................................................................................8

5. Wiring ...............................................................................................................................9

6. Parts List...........................................................................................................................107. Installation Precaution........................................................................................................10

8. Specifications....................................................................................................................11

1.Features

This product was designed with circuitry that allows trouble-free, long-lasting operation and a clean

picture. It is easily mountable on the wall without any modifications to the wall itself.

Easy installa tionIt is a wall-mountable design for easy installation.

Clear picture

This product utilizes a flat CRT tube to provide you with a clear picture.

Crisp picture

This product incorporates the latest technology to provide a crisp picture.


7/13

- 6 -

2 . Part s Check list an d Fun ctions

1 Monitor Screen 4 Flat B/ W CRT

2 Microphone Sends voice to the camera.

3 Bell volume control Controls the volume of the ringtone.

4 Power switch Controls the power to the unit.

5 Brightness control Controls the brightness of the screen.

6 APV-4RH(Guardroom) Allows communication with the guardroom.

DPV-4RH(Open) Opens the front gate if so equipped.

7 Priority Call Allows only the households voice to be heard

8 Monitor/ Talk Displays the screen and initiates communication9 LED light Power on: Yellow, Signal from camera or guardroom : Red

During a conversation : Red

10 Speaker Voice from the camera or guardroom is delivered

11 Door release connection socket Connects to the camera

12 Individual(DPV models), guardroom(APV models) connection socket

13 Power cord insertion trenches

Monitor(DPV-4RH)

Camera(DRC-403N)

1 Front Panel

2 Camera protection window

3 CCD camera lens

4 Infrared LED : Allows for good visibility even when the lighting

conditions are less than adequate

5 Speaker Sound from the monitor is delivered

6 Page button pages the monitor to initiate communication

7 Screw hole cover

8 Camera Pivoting Lever Allows the camera lens to pivot about for theoptimum angle

9 Monitor connection socket


8/13

- 7 -

3. Installation Instructions

Monitor Installation

Cam era Installation

Install atio n Location

Avoid installing the camera where it is

exposed to direct sunlight

The visitors image may not be clearly

visible if there are surrounding lighting

sources behind the visitor in which case,

separate lighting may be necessary.

Install atio n LocationAvoid installation in the following type ofenvironments :

In direct sunlightHigh temperature, humidity areasAreas where the unit is exposed to toxicchemicalsAreas where a strong magnetic field is present

Areas where appliances such as a heater orair conditioner is present

Monitor m ounting heightThe mounting height should be

approximately 5ft(145cm) off theground


9/13

- 8 -

4. Operat ion

Call duration and monitor display time :

When only the screen is displayed with no dialog : 30 sec.

When dialog takes place : 1min. 30 sec.

The maximum duration for a dialog between the monitor and

the guardroom station is 5 minutes at a time.

Note : The lamp will turnyellow once the callhas ended

1 . Visitor Call

2 . Dialog w ith the guard room (APV-4RH)

a chime sounds

end the call

Visitorpressescall buttonon camera

the visitorsimage

appears onthe monitor

the talk button ispressed on the

monitor forconversation

Monitor of theguardroom

guardroom Call

dialog begins

A visitor callsfrom the front

gate

the dooropens

3 . Door release f unction(DPV-4RH)

the outside image will be

visible on the screen for30 seconds at a time.

4 . To view the outside from the indoor m onitor

to end the call

end the dialog withthe guardroom

call from the

front gate

Dialog with theguardroom

the screen

image becomes

larger dialog with the visitor

the dialog with thevisitor ends

call from theguardroom

Dialog witha visitor

a continuousbeep

will be heard

the screenturns off

dialog with theguardroom begins

dialog is initiated


10/13

- 9 -

5. Wir ing

Wiring precautions

1. If high voltage cables are present in the vicinity, use a coaxial cable with metal outer casing.

2. If any external wiring is exposed, it may cause a short and become a cause of malfunction or fire.

3. When connecting the monitor and camera, make sure that the monitor power is off.(Turn on thepower after plugging the AC power cord into the outlet)


11/13

- 10 -

6. Parts list

7. Precau tion du ring instal la t ions

DPV-4RHOR APV-4RH) 1

Wall-mountable bracket 1Owners manual, main unit 1wall-mounting screws 4connector(4P) 1connector(2P) 1camera(optional equipment) 1

Monitor(DPV-4RH)

*Do not install where excess dust or humidity is present

* Connect the wires to the proper socket

* Attach the equipment securely

* Do not install the unit where it is exposed to constant sunlight or rain

* Be careful not to scratch the door camera lens cover

(APV-4RH)


12/13

- 11 -

8. Specifications

Connection method 4 wires in polarityVoltage requirements AC 100V~240V, 50/ 60HzPower consumption Standby mode : 2.5W, during operation : 15WMonitor screen 4 B/ W flat CRT monitorCommunication method Simultaneous typeCall tone Electronic chime/ melodic tone(guardroom)Calling distance 50m (0.65)Operating temperature 0~ +40(32 ~ 104)

Dimensions(mm) 211(W) X 226(H) X 52(D)

Mo del : DPV-4RH/ APV-4RH

Connection method 4 wires in polarityVoltage requirements DC 12V(supplied from the monitor)Imaging Device 1/ 3 B/ W CCDViewing Angle Horizontal : 68, Vertical : 55

Adjustability Up : 29, Down : 26

Minimum illumination 0.1 Lux (50cm in front of the camera)Operating temperature -10 ~ +50 (14 ~ 122)Dimensions(mm) 125(W) X 182(H) X 46(D)

M od el : DRC-40 3N


13/13

513-11, Sangdaewon-dong, Jungwon-gu,

Seongnam-si, Gyeonggi-do, Korea

Intl Business Dept. :

Tel.; +82-31-7393-540~550

Fax.; +82-31-745-2133

Web site : www.commax.com.kr

Documents

APV-4RH, DPV-4RH