Upload
rheins2000
View
166
Download
14
Embed Size (px)
DESCRIPTION
Basic ASD Engineering calculations for simple analysis of steel connections
Citation preview
BASIC ENGINEERING CALCULATIONS (ASD)
FLEXURE DESIGN
FLEXURE–the available flexural strength, Mn/Ω must be greater than Required Strength, Ma
Ma ≤ Mn/Ω
Ω = Safety Factor for given loading type (or limit state) --- Ωb = 1.67 for Bending
ELASTIC FLEXUREf = Mc/I = Mmax/S
Sreqd = Mmax/fMn = MCR = SXfy
PLASTIC FLEXUREf = M/A
Mn = Mp = ZXfy
SLENDERNESS PARAMETERSFLB, λ = bf/2tf (FLANGE LOCAL BUCKLING)WLB, λ = h/tw (WEB LOCAL BUCKLING)LTB, λ = Lb/ry (LATERAL-TORSIONAL BUCKLING)Ma = Beam Bending Moment (Maximum Service Load Moment)MCR = Elastic Moment (the second-highest nominal Flexural Strength – when λ = λR) = FCRS = 0.7FySx
Mn = Nominal Moment Capacity (Nominal Flexural Strength – Must be divided by Ω for ASD Capacity)MP = Plastic Moment (the highest possible nominal Flexural Strength – for braced & compact members) = FYZMy = Yield Momentλ = Width-Thickness Ratio (dividing line is λP --- if λ < λP, the section is compact and MP can be used)∆ = DeflectionL, l = SpanI = Moment of InertiaLb = Unbraced Length (Lb≤Lp for a properly braced member)SX = Elastic Section Modulus about the x-axis = I/c
Rectangle: S = bd2/6Solid Round: S = πd3/32Tube: S = [bodo
3-bIdI3]/6d
ZX = Plastic Section Modulus about the x-axis Rectangle: Z = bd2/4Solid Round: Z = d3/6Tube: Z = [do
3-dI3]/6
E = Modulus of Elasticity =29,000 ksi for common steelsFy = Yield Stress of Steel (36ksi for A36 Steels)FCR =- Elastic Critical Buckling Stress (determined by equations)IX = Moment of Inertia about x-axisCb = Lateral-Torsional Buckling Modification FactorLb = Unbraced LengthJ = Torsional Constant
COMMON ENGINEERING EQUATIONS
Plastic Moment Capacity, MP = FyZx, so Mp/Ω = FyZx/1.67 = 0.6FyZx
Elastic Moment Capacity, Mr = FySx, so Mr/Ω = FySx/1.67 = 0.6FySx
Shear Strength, Vn = 0.6FyAw so Vn/Ω = 0.6FyAw/1.50 = 0.4FyAw
SIMPLE BEAM, UNIFORM LOAD (FROM 13TH EDITION TABLE 3-23)
VMAX = wl/2 MMAX = wl2/2∆ = 5wl4/384EI
SIMPLE BEAM, CONCENTRATED LOAD AT CENTER (FROM 13TH EDITION TABLE 3-23)
VMAX = P/2 MMAX = Pl/4∆ = Pl3/48EI
SIMPLE BEAM, CONCENTRATED LOAD (FROM 13TH EDITION TABLE 3-23)
WELD STRENGTH
ALLOWABLE STRENGTH– for ASD, the allowable strength, Rn/Ω must be greater than the Required Strength, Ra
Ra≤ Rn/Ω
Ω = Safety Factor for given loading type (or limit state)
WELDSThe allowable strength of welds shall be the lower value of:
1) Base Material Strength (Rn = FBMABM)2) Weld Metal Strength (Rn = FWAW)
FW = Nominal Strength of the Weld Metal per Unit Area (ksi) = 0.60FEXX
FBM = Nominal Strength of the Base Metal per Unit Area (ksi) = 0.60Fu
AW = Effective Area of the Weld (in2)ABM = Effective Area of the Base Metal (in2)
FEXX = ultimate strength of welding electrode,(ksi) = Fu (weld metal)(cos 45°)(1/16”)Fu = ultimate strength of base metal
Using ASD Table J2.5 (16.1-99), for allowable strength of welds in shear (the most conservative case of all weld loading), FBM or FW = 0.60 FEXX
Rn/Ω = 0.60FEXX/2.00 = 0.30FEXX = 0.30 (FyEXX)(sin 45°)(1/16”) = (0.30)(70ksi)(0.707)(1/16”)Note: (sin 45°)(1/16”) = effective throat for 1/16” leg of weld = WORST CASE
Rn/Ω =0.928k/in of weld leg for longitudinally loaded fillet (worst case)
Rn/Ω =1.392k/in of weld leg for transversely loaded fillet(increased loading angle strength = 1+0.5sin 1.5 Ѳ) = 1.5 for Ѳ = 90°
BOLT STRENGTH
ALLOWABLE STRENGTH(ASD) - allowable strength, rn/Ω must be greater than the Required Strength, Ra
ra≤ rn/Ω
BOLTS IN SIMPLE BEARING CONNECTIONSThe allowable sheara strength, rn of BOLTS in simple bearing connections is as follows:
rn = FnvAb* (# of shear planes) with Ω = 2.00
Fnv = Nominal Shear strength of fastener (ASD Table J3.2) = 0.50Fu (threads excluded) = 0.40Fu (threads included)
Ab = Area of bolt (unthreaded body area only)
Fnv values for common bolts: Using ASD Table J3.2 (16.1-104),A325X bolts (threads excluded) = 60 ksiA325N bolts (threads included) = 48 ksiA307 bolts = 24 ksiA36 Threaded Rod = 14.4 ksi
So, for a ¾” A325 bolt in simple bearing, threads included,rn = FnvAb = (48 ksi) (π (.375”)2) = (48)(0.44178) = 21.21k
rn/Ω = 21.21/2 = 10.6k
rn/Ω =10.6k/BOLT (A325N)(SINGLE SHEAR)rn/Ω =13.3k/BOLT (A325X)(SINGLE SHEAR)rn/Ω =5.30k/BOLT (A307)(SINGLE SHEAR)
(SEE ASD TABLE 7-1)
for a ¾” A36 Threaded Rod in double shear, threads included,rn = FnvAb = 0.40FuAb = (0.4)(36 ksi) (π (.375”)2) = (14.4)(0.44178) = 6.36k
rn/Ω = 6.36/2 = 3.18k
rn/Ω =3.18k/A36 THREADED ROD (SINGLE SHEAR, THREADS INCLUDED)
BOLTS IN SLIP-CRITICAL CONNECTIONS
rn = µDnhscTbNs with Ω = 1.5 (designed at serviceability limit state) Ω = 1.76 (designed at required strength level)
rn/Ω =6.28k/BOLT (A325SC, CLASS A)(SINGLE SHEAR – SSH, SERVICIABILITY)rn/Ω =5.38/BOLT (A325SC, CLASS A)(SINGLE SHEAR – SSH, STRENGTH LIMIT)
(SEE ASD TABLE 7-3)
WEDGE ANCHOR DESIGN
AVAILABLE STRENGTH– for ASD, the available strength, Rn/Ω must be greater than the Required Strength, Ra
Ra≤ Rn/Ω
Ω = Safety Factor for given loading type (or limit state) = 4