Upload
others
View
1
Download
0
Embed Size (px)
Citation preview
WASSERBEHANDLUNG PHYSIKALISCH/ CHEMISCHE VERFAHREN
63
DAS DIDAKTISCHE BEGLEITMATERIAL
MESS- UND REGELUNGSTECHNIK
SCHALTSCHRANK MIT BEDIENELEMENTEN
KONTINUIERLICHER UND PRAXISNAHER PROZESS
Das gut strukturierte didaktische Begleitmaterial stellt die Grundlagen dar und führt Schritt für Schritt durch die Versuche. Die Materialien werden als Papierdruck in einem Ordner und zusätzlich auch als PDF-Dateien auf einer CD geliefert.
Updates Wenn es Neuerungen und Ergänzungen bei CE 586 gibt – insbesondere bei dem didaktischen Begleit-material – werden Sie als Kunde von GUNT darüber informiert.
Einsatz moderner Mess- und Regelungs- technik
Durchflussmesser
Leitfähigkeitsaufnehmer
Temperaturaufnehmer
Regelung des pH-Wertes im Fällungsbehälter
Bedienelemente für alle Haupt- komponenten
Übersichtliche Anordnung der Bedienelemente
Digitale Anzeige von Messwerten
Digitaler Regler für pH-Wert
Ein großflächiges, deutliches Prozessschema auf dem Schalt-schrank ermöglicht die einfache Zuordnung aller Komponenten.
CE 586 FÄLLUNG UND FLOCKUNG
Fällungsbehälter Flockungsbecken Lamellenklärer
Dosierpumpen
Exakte Chemikalienzugabe durch Verwendung industrieller Dosierpumpen
Didaktisches Begleitmaterial für CE 586
1 2 3E N E R G Y & E N V I R O N M E N T
CE 586 PRECIPITATION AND FLOCCULATION
3 Unit description
33
All
right
s re
serv
ed, G
.U.N
.T. G
erät
ebau
, Bar
sbüt
tel,
Ger
man
y 03
/201
0
– Plug the supply unit connector into the con-
necting socket on the switch cabinet (item
56 in Fig. 3.11, Page 23).
• Connect the unit to the mains electricity supply.
• Make sure that the valves on the unit are
closed, except for valves V3 and V9.
Valve V3 is shown in Fig. 3.24. Valves V3 and
V4 are closed by turning the hand wheel clock-
wise. They are opened by turning the hand
wheel anticlockwise.
• Fill the raw water tank (B1) with water.
• Fill tanks B6, B7 and B8 with water.
• Set the main switch (item 57 in Fig. 3.11,
Page 23) to "1".
• Start the raw water pump (P1). If necessary,
add more water to the raw water tank (B1).
• Start pumps P2 to P4. If necessary, add more
water to tanks B6 to B8.
• Fill the trainer until treated water flows into the
treated water tank (B4).
• Start the sludge pump (P5).
• Continue operating the unit until the treated
water tank (B4) is full.
• Repair any leaks that occur.
• Stop pumps P1 to P5.
• Drain the entire unit.
• Remove the pH value sensors, observing the
instructions in Chapter 3.4.3, Page 28ff.
• Remove the conductivity sensors, observing
the instructions in Chapter 3.4.4, Page 31.
Fig. 3.22 Hose line for raw water, on
supply unit
Fig. 3.23 Hose line for raw water, on
trainer
Fig. 3.24 Valves V3 and V4V3
V4
gleitmaterial für CE 586
33
,
y,
ore
the
eated
ving the
ff.
observing
ge 31.
E N E R G Y & E N V I R O N M E N T
CE 586 PRECIPITATION AND FLOCCULATION
3 Unit description
21
All
right
s re
serv
ed, G
.U.N
.T. G
erät
ebau
, Bar
sbüt
tel,
Ger
man
y 03
/201
0
3.3.3 Lamella separator
Suspension refers to a mixture of substances
made up of a liquid containing finely distributed
solids. After passing through the precipitation and floccu-
lation steps, the raw water has been converted
into a suspension. This suspension passes into
the lamella separator (11).Fig. 3.8 shows the layout of the lamella separa-
tor (11), Fig. 3.9 its function.The lamella separator (11) separates the sus-
pension into treated water and sludge. The
treated water flows freely through the outlet into
the treated water tank (26). The sludge contains
the solids formed. Separation occurs because of
sedimentation of the specific heavier solids.
Thus, the solids sink downwards in the lamella
separator. Therefore, the sludge extraction is
located at the bottom and the outlet at the top. The height of the outlet determines the level in the
lamella separator.The lamella separator contains individual
lamellae, which take the form of inclined panels.
They increase the effective sedimentation area.
The lamellae fill the entire width of the lamella
separator and are combined into a lamella bun-
dle. The flow in the lamella separator is deter-
mined by the lamella bundle.Fig. 3.10, Page 22 shows the lamella bundle. It
is designed to be removable. This allows the
lamella bundle to be cleaned at the end of the
experiment.
Fig. 3.8 Lamella separator (11), layout
Fig. 3.9 Lamella separator (11), function
Lamella bundleLamella
Sludge extraction
Inle
t
Out
let
Sludge
Sus
pens
ion
Tre
ated
wat
er
Fällung und Flockung ist ein physikalisch/chemi-sches Verfahren der Wasserbehandlung. Ein wichtiges Anwendungsgebiet dieses Verfahrens ist die Entfernung von gelösten Metallen. Dies ist oft bei der Trinkwasseraufbereitung und bei der Behandlung kontami-nierter Grundwässer erforderlich.
Mit CE 586 kann dieses Verfahren sehr praxisnah unterrichtet werden.
Praxisnahe Ausbildung im Bereich der Wasserbehandlungikalisch/chemi-handlung. Ein
ses Verfahrens etallen. Dies ist g i-
n .
g im Bereich der Wasserbehandlung
E
Q
E
Q
T
F
Fällung gelöster Stoffe
VersorgungseinheitVersuchsstand
Bildung von Flocken durch Koagulation und Flocculation
Ein Mitarbeiter der British University in Egypt (Kairo) erklärt die Funktionsweise von CE 586.
Abtrennung der Flockendurch Sedimentation
1 2 3
Einen interessanten Videofilm zu CE 586 finden Sie als DVD auf Seite 77.
Department of Civil Engineering