Upload
corvinno-technology-transfer-center-nonprofit-public-ltd
View
105
Download
1
Embed Size (px)
Citation preview
3.12.1 KTE PCB ellenőrzése CAC-kazettás egység
3., Fő hibakijelzések CH05 (BTEKTE kommunikációs hiba)
Cél KTE PCB ellenőrzése Módszer LED, biztosíték, REACTOR csatlakozási hiba
① REACTOR csatlakozó ② Biztosíték vizsgálata ③ KTE LED világít?
※ A saru terméktől függően ettől eltérhet
0 Ω
※ Cseréld ki a panelt, ha a LED nem világít a feszültség kiadása után.
※ Ha kiégett a biztosító, cseréld ki a panelt
3.12.2 Installációs körülmények hatása a BTE/KTE kommunikációra
Cél Zajforrások feltárása Módszer Hibaforrások keresése
Sodrott kötés: NEM Forrasztott kötés: IGEN
① Kommunikációs vezetékek csatlakoztatása: Összesodrás nem elfogadható. Forrasztással kössük össze a vezetékeket.
② Ér kicsúszik a saruból.
Kommunikációs ér
③ A sodrott, szigszalagozott kötést átszúrja a vezeték és hozzáér egy másik vezetőhöz
④ Átmeneti ellenállás oxidáció miatt megnő: Forraszott kötés szükséges
3., Fő hibakijelzések CH05 (BTEKTE kommunikációs hiba)
3.3.13 CH05(Indoor/Outdoor Device Communication Error) Detection by indoor devices
CH05 (Indoor/Outdoor Device Communication Error)
Resetting power source: Wait for 3 minutes after turning the power of the product off.
Wire connection state
Sub-items for checkingItems for checking
Replacing indoor PCB
Wire tongue termination
Communication cable length
Application of shield lines
Grounding
Items Contents
Purpose Checking for smooth data sending/receiving between indoor/outdoor devices
Condition for Generation Damage and installation of outdoor device PCB
Resetting power source
Outdoor PCB Checking for LED Off
Installation
※ Refer to 3.3.13.1
※ Refer to 3.3.13.2
No power
1.3 Measures for Main Error Codes
3.3.13.1 Checking Method of Outdoor PCB_ SRAC
Purpose Checking whether outdoor PCB is normalItems for checking
Lighting of LED, fuse damage, and reactor connection error
① Check reactor connection state.
② Check fuse state.
※ The shapes of housing may be different by product.
0 Ω
※ Replace outdoor PCB in LED Off state after resetting.
③ Check whether outdoor PCB LED is lighted.
※ Replace outdoor PCB in case of Fuse Off state.
CH05 (Indoor/Outdoor Device Communication Error) 1.3 Measures for Main Error Codes
3.3.13.1 Checking Method of Outdoor PCB_ Cassette
Purpose Checking whether outdoor PCB is normalItems for checking
Lighting of LED, fuse damage, and reactor con-nection error
① Check reactor connection state.
② Check fuse state.
The shapes of housing may be differ-ent by product.
0 Ω
Replace outdoor PCB if LED is turned off after resetting.
③ Check whether outdoor PCB LED is lighted.
Replace outdoor PCB in case of Fuse Off state.
CH05 (Indoor/Outdoor Device Communication Error) 1.3 Measures for Main Error Codes
3.3.13.2 Installation environment interfering with the communication of indoor/outdoor devices
PurposeInstallation environment interfering the com-munication
Items for checking
Check installation error points
NG NG OK
① The communication lines of the indoor /outdoor devices are installed by wire-to-wire method.
: In case of additional connection, connect the wires with soldering as shown below.
② Wire tongue-termination fault.
Com-muni-cation line
Wire-to-WireNetura
③ The cut section of the wire passes the insulation tape and causes a short with another wire.
④ Communication noise by oxidized wire arrange-ment : Soldering is required.
CH05 (Indoor/Outdoor Device Communication Error) 1.3 Measures for Main Error Codes