Embed Size (px)
Citation preview
FlexCore Bollard | Page 1 of 5
mccue.comMcCue CorporationPeabody, Massachusetts, USA
+1 (800) 800 [email protected]
McCue UK & EuropeMilton Keynes, United Kingdom
+44 (0)1908 365 [email protected]
McCue Asia 迈客(厦门)有限公司
Xiamen, Fujian, China+86-592-2200790
FlexCore Bollard
? Questions
INSTALLATION INSTRUCTIONS
Tools Required
Components
Optional
Shell Epoxy /ResinFixings (3) Locking
Pin (2)Core
Assembly
FlexCore 6 FlexCore 4
19mm, 3/4"
22mm, 7/8"
FC 4
FC 6
FC 4FC 6
FlexCore Bollard | Page 2 of 5
1
2
Flex Core Installation
SHELL INNER KIT 1/2" FIXINGS LOCKING PIN EPOXY/RESIN
1. PLACE BOLLARD AND MARK HOLES
EPOXY GUN
3.5”89mm
NOTE PINORIENTATION
DIRECTION OF IMPACTS
TOP VIEW TOP VIEW
PENCILMARKS
2. DRILL HOLES
3. DRILL HOLES 4. FILL HOLES W/ EPOXY
EPOXY3/4
OF HOLE
FlexCore 4
Fixing Depth116mm (41/2in)
Fixing Diameter 13mm (1/2in)
Hole Diameter 19mm (3/4in)
Fixing Height80mm (31/8in)
FlexCore 6
Fixing Depth119mm (45/8in)
Hole Depth143mm (55/8in)
Fixing Diameter 16mm (5/8in)
Hole Diameter 22mm (7/8in)
Fixing Height84mm (33/8in)
FlexCore Bollard | Page 3 of 5
5. INSTALL FITTING INTO HOLES
7. PLACE FLEXCORE OVER FITTINGS(NOTE PIN ORIENTATION)
6. WIPE EXCESS EPOXY AWAY
8. WAIT FOR EPOXY TO CURE
5. INSTALL FITTING INTO HOLES
7. PLACE FLEXCORE OVER FITTINGS(NOTE PIN ORIENTATION)
6. WIPE EXCESS EPOXY AWAY
8. WAIT FOR EPOXY TO CURE
2. DRILL HOLES
3. DRILL HOLES 4. FILL HOLES W/ EPOXY
EPOXY3/4
OF HOLE
FlexCore 4
Fixing Depth116mm (41/2in)
Fixing Diameter 13mm (1/2in)
Hole Diameter 19mm (3/4in)
Fixing Height80mm (31/8in)
FlexCore 6
Fixing Depth119mm (45/8in)
Hole Depth143mm (55/8in)
Fixing Diameter 16mm (5/8in)
Hole Diameter 22mm (7/8in)
Fixing Height84mm (33/8in)
2. DRILL HOLES
3. DRILL HOLES 4. FILL HOLES W/ EPOXY
EPOXY3/4
OF HOLE
FlexCore 4
Fixing Depth116mm (41/2in)
Fixing Diameter 13mm (1/2in)
Hole Diameter 19mm (3/4in)
Fixing Height80mm (31/8in)
FlexCore 6
Fixing Depth119mm (45/8in)
Hole Depth143mm (55/8in)
Fixing Diameter 16mm (5/8in)
Hole Diameter 22mm (7/8in)
Fixing Height84mm (33/8in)
3 4
5 6
FlexCore Bollard | Page 4 of 5
10. INSTALL SHELL 11.
SHELL
9. WE RECOMMEND TIGHTENING NUTS WITH AN IMPACT DRIVER (HEAVY DUTY DRILL WITH A SOCKET WRENCH ATTACHMENT).
NUT
7 8
9
5. INSTALL FITTING INTO HOLES
7. PLACE FLEXCORE OVER FITTINGS(NOTE PIN ORIENTATION)
6. WIPE EXCESS EPOXY AWAY
8. WAIT FOR EPOXY TO CURE
Read Epoxy instructions for recommended drying times.
FlexCore Bollard | Page 5 of 5
10. INSTALL SHELL 11.
SHELL
9. WE RECOMMEND TIGHTENING NUTS WITH AN IMPACT DRIVER (HEAVY DUTY DRILL WITH A SOCKET WRENCH ATTACHMENT).
NUT
10. INSTALL SHELL 11.
SHELL
9. WE RECOMMEND TIGHTENING NUTS WITH AN IMPACT DRIVER (HEAVY DUTY DRILL WITH A SOCKET WRENCH ATTACHMENT).
NUT
10 11
Installation instructions are provided for guidance only. The seller assumes no liability regarding improper installation or misapplication of its products. It is the installer’s responsibility to check for proper installation and, if in doubt, contact McCue Customer Care for assistance. ©2014 McCue Corporation. AUG2014
12. OPTIONAL! POUND IN PIN TO LOCK SHELL DOWN
33”838mm
PIN
Optional OpcionalFakultativ Optionnel 可选
