(for MAV-555 MULTI ACCESS VIDEO DISK RECORDER) MAVE …(for MAV-555 MULTI ACCESS VIDEO DISK RECORDER) MAVE-D555 (Ver. 1.30) ... 9100 format. Also, when the VTR is used as a player

DIAL PANEL(for MAV-555 MULTI ACCESS VIDEO DISK RECORDER)

MAVE-D555 (Ver. 1.30)

OPERATION MANUAL [Japanese/English]

1st Edition (Revised 1)Serial No. 10001 and Higher

電気製品は、安全のための注意事項を守らないと、火災や人身事故になることがあります。

このオペレーションマニュアルには、事故を防ぐための重要な注意事項と製品の取り扱いかたを示してあります。このオペレーションマニュアルをよくお読みのうえ、製品を安全にお使いください。お読みになったあとは、いつでも見られるところに必ず保管してください。

1 (E)

En

glish

For the customers in the U.S.A.

WARNINGThis equipment has been tested and found to comply withthe limits for a Class A digital device, pursuant to Part 15 ofthe FCC Rules. These limits are designed to providereasonable protection against harmful interference when theequipment is operated in a commercial environment. Thisequipment generates, uses, and can radiate radio frequencyenergy and, if not installed and used in accordance with theinstruction manual, may cause harmful interference to radiocommunications. Operation of this equipment in a residentialarea is likely to cause harmful interference in which case theuser will be required to correct the interference at his ownexpense.

You are cautioned that any changes or modifications notexpressly approved in this manual could void your authorityto operate this equipment.

The shielded interface cable recommended in this manualmust be used with this equipment in order to comply with thelimits for a digital device pursuant to Subpart B of Part 15 ofFCC Rules.

For the customers in EuropeThis product with the CE marking complies with the EMCDirective (89/336/EEC) issued by the Commission of theEuropean Community.Compliance with this directive implies conformity to thefollowing European standards:• EN55103-1: Electromagnetic Interference (Emission)• EN55103-2: Electromagnetic Susceptibility (Immunity)This product is intended for use in the followingElectromagnetic Environment(s):E1 (residential), E2 (commercial and light industrial), E3(urban outdoors) and E4 (controlled EMC environment, ex.TV studio).

Pour les clients européensCe produit portant la marque CE est conforme à la Directivesur la compatibilité électromagnétique (EMC) (89/336/CEE)émise par la Commission de la Communauté européenne.La conformité à cette directive implique la conformité auxnormes européennes suivantes:• EN55103-1: Interférences électromagnétiques (émission)• EN55103-2: Sensibilité électromagnétique (immunité)Ce produit est prévu pour être utilisé dans lesenvironnements électromagnétiques suivants:E1 (résidentiel), E2 (commercial et industrie légère), E3(urbein extérieur) et E4 (environnement EMC contrôlé ex.studio de télévision).

Für Kunden in EuropaDieses Produkt besitzt die CE-Kennzeichnung und erfüllt dieEMV-Direktive (89/336/EEC) der EG-Kommission.Die Erfüllung dieser Direktive bedeutek Konformität für diefolgenden Europäischen Normen:• EN55103-1: Elektromagnetische Interferenz (Emission)• EN55103-2: Elektromagnetische Empfindlichkeit

(Immunität)Dieses Produkt ist für den Einsatz unter folgendenelektromagnetischen Bedingungen ausgelegt:E1 (Wohnbereich), E2 (kommerzieller und in beschränktemMaße industrieller Bereich), E3 (Stadtbereich im Freien) undE4 (kontrollierter EMV-Bereich, z.B. Fernsehstudio).

2 (E) Table of Contents

Table of Contents

Chapter 1 Overview

1-1 MAVE-D555 Overview .................................. 1-11-2 Features .......................................................... 1-11-3 Changes from Version 1.00 ............................ 1-2

1-3-1 Changes from Version 1.00 to 1.10 ........ 1-21-3-2 Changes from Version 1.10 to 1.20 ........ 1-21-3-3 Changes from Version 1.20 to 1.30 ........ 1-2

1-4 Names and Functions of Parts ...................... 1-41-4-1 Console.................................................. 1-41-4-2 Rear View............................................... 1-7

1-5 System Configuration Example ................... 1-8

Chapter 2 Operation

2-1 Edit Point Operations ................................... 2-12-1-1 Setting Edit Data with the Number

Keypad .................................................. 2-12-1-2 Confirming Edit Data (RECALL)......... 2-12-1-3 Changing Edit Data ............................... 2-12-1-4 Jumping to an Edit Point (GO TO) ....... 2-22-1-5 Clearing Edit Data (CLEAR) ................ 2-32-1-6 Edit Totals ............................................. 2-3

2-2 Operations for Each Function ...................... 2-42-2-1 DMC Editing ......................................... 2-42-2-2 Voice Over Editing ................................ 2-52-2-3 Setting an Effect Pattern ........................ 2-52-2-4 Setting Effect Parameters ...................... 2-92-2-5 Using a Track Ball............................... 2-122-2-6 Registering Effects .............................. 2-132-2-7 Inserting Text and Graphics ................. 2-142-2-8 Editing with the Player BUS................ 2-192-2-9 GPI Output ........................................... 2-202-2-10 Audio Channel Mix/Swap Editing ..... 2-212-2-11 Support of EDL Export ...................... 2-23

2-3 Using the Menus .......................................... 2-262-3-1 Operations and Menus ........................ 2-26

2-4 Using the MAVE-D555 with the EditingFader Panel .................................................. 2-292-4-1 Adjusting the Recording Level in

Real Time at the Recording Interval ... 2-29

Appendixes

Specifications .........................................................A-1Menu List ..............................................................A-2Effect Parameter List ...........................................A-4TITLE Key, Downstream Key,and Player BUS Setting Example ........................A-7

Chapter 1 Overview 1-1 (E)

Chapter 1 O

verview

1-1 MAVE-D555 Overview

The MAVE-D555 is a dial panel that connects to theMAVE-F555, an editing panel that is made for usewith the MAV-555 multi-access video disk recorder.By using the MAVE-D555, MAVE-F555 (editingpanel for the MAV-555), and Editing Fader PanelBKNE-1011 in an MAV-555 based editing system, wecan bring you new exciting features of the MAVE-D555 an enhance the features of the other units.

For example, with the MAVE-D555 you can now:• Set the duration and IN and OUT points from the

number keypad.• Select and GO TO selected an IN or OUT point.• View more information with the LCD panel.• Adjust the recording level of the audio during

recording with the audio feed panel.• Use effects during editing.

Notes

• Use of the MAVE-D555 requires an MAV-555 of Ver. 2.32, an MAVE-F555 of Ver. 2.30, and a BKMA-560 ofVer. 1.10.

• For reasons of simplicity, we refer to the MAV-555, MAV-555A, MAV-555SS (SD mode), andMAV-777 as the “MAV-555”.

1-2 Features

Linear editing support function

When using the MAVE-D555 and MAVE-F555 tooperate the MAV-555, you can perform JOG dial,PLAY, STILL, REW, FF, SHUTTLE, JOG, and DMCoperations just as with the earlier BVE series editor.

Nonlinear editing function

Operating the MAV-555 configured with the MAVE-D555 and the MAVE-F555, allows you to continueusing all the features of the BVE editor with theaddition of nonlinear editing which was not featuredon the previous BVE editor.

Detailed LCD panel display

The MAVE-D555 LCD panel allows you to view thestatus of effect settings, use a scratchpad, and confirmeach code with menus for each function duringoperations. The LCD panel also displays the currentversion numbers of the MAVE-D555 and theconnected MAVE-F555.

Direct numeric entry

You can now enter numbers directly from the numberkeypad for IN and OUT point, duration, and time codesettings. You can also use the GO TO key to cue up aswell as enter the settings directly.

Editing fader panel

By connecting the Editing Fader Panel BKNE-1011 tothe MAVE-D555, you can control the recording levelof the recorder during editing.

Editing using effects

By installing an optional BKMA-560/561 board in theMAV-555 and then using the MAVE-D555 configuredwith an MAVE-F555 and BKNE-1011 together andthen employing this system for editing, you can selecteffects from the MAVE-D555 and enter parameters forthe selected effects.

Editing mosaics and other sophisticatedeffects

Using pointing device such as a track ball, you canadjust edit special effects, such as by adjusting theXYZ location of mosaics.

Inserting Text and Graphics

You can insert text and graphics when applying effects(Title key) or into a cut to which effects have alreadybeen applied (Downstream key).

Audio Channel Mix/Swap Editing

You can mix and swap audio channels in the intervalwhere materials are presented during editing.

1-2 (E) Chapter 1 Overview

Chapter 1 O

verview

1-3 Changes from Version 1.00

1-3-1 Changes from Version 1.00 to 1.10

Inserting Text and Graphics (Downstream key)

The DSK (Downstream key) can be used to insert text and graphics into acut to which effects have already been applied.

Audio Channel Mix/Swap Editing

The MAVE-D555 allows mixing and swapping audio channels in theinterval where materials are presented during editing.

Functional Improvements when Using the Editing Fader Panel

• When setting the recording level when the AUDIO key of the MAVE-F555 is lit and a Player port is selected, the fader is enabled. Therefore,before performing a PREVIEW or EXECUTE/REC, the level can beconfirmed.

• When the Editing Fader Panel is enabled (the AUDIO key is lit),information can be superimposed on the monitor for confirmation.


Support of EDL Export from BZMA-E555

When the MAV-555 is used as a recorder during editing and used inparallel with the BZMA-E555 file transfer program (sold separately), it ispossible to output EDL files (.edl) of editing results in the SONY BVE-9100 format. Also, when the VTR is used as a player during editing, it ispossible to enter a tape’s reel name.


Time Tracking Function

When you finish an editing procedure, the recorder and player OUT pointsare automatically moved as the following IN points. Further, if therecorder IN point is modified through a new editing operation, the playerIN point is modified automatically (automatic time tracking). Even if youmodify the player IN point and time tracking is lost, you can manuallyreturn it to its original position (manual time tracking).


Chapter 1 O

verview

REC OFF Function

When editing with a specified OUT point or duration, or editing withoutspecifying an OUT point (OPEN END Edit), pressing the MAVE-F555EXECUTE/REC key resets the OUT point and ends the current recording.

TITLE Function

Version 1.10 only supported DSK (Downstream key). Using the TITLEfunction, it is now possible to insert text and graphics while applyingeffects.

Editing with a BUS Signal

It is possible to edit the external VIDEO signal input to the player BUSfrom the optional BKMA-560 built-in Internal Video, or to the left SPAREterminal on the MAV-555 connector panel (with the MAV-555SS in SDmode or MAV-555A, the DSK IN VIDEO terminal).

Saving and Recalling Cut Point Information

When the MAV-555 is turned off, cut point and other such editinginformation is cleared and cannot be retrieved. However, you can save andrecall the cut point information by pressing the STORE key while holdingthe SHIFT key.

Removing Recorder Port Restrictions

When erforming the following operations, it is now possible to specify theMAV-555 RP port or a VTR as the recorder port.• Adjusting the recording level using the Editing Fader Panel.• Performing audio channel mix or swap editing.

Video Support of Voice Over Editing

Voice over editing can be performed and added at the end of editedmaterial. It is now also possible to add video in the same manner.


Chapter 1 O

verview

REVSOFTBORDEDIT

LASTX

CLEAR

LOCMAN

PATTPRMTR

SOFIN

EOFOUT

STARTTOTAL

SPEEDDUR

T-TRACKF/TC

SCRGO TO

STBOFPLAY

STOPSHTL

EJECTSTILL

STEP-REW

STEP+FF

MENU+

SCR-C0

CTL/TC00

T-SET-

MARKSPEED

JOG DMCSHIFT ALL STOP

987

654

321

RETURNENTER

PQRS TUV WXYZ ! < = >

GHI JKL MNO _ / " @

ABC

, . : ; & # * ?

DEF ( ) [ ]

1 LCD (information display)The LCD displays the following information:• Status for the effect settings. Allows you confirm or

change the settings while viewing the display.• Scratchpad• Time codes for IN and OUT points, DUR (duration),

TOTAL (total duration of the edited material),START (edit start point).

• Menus. Open and view the menus to confirm orchange settings.

• Current version numbers for the MAVE-F555 andMAVE-D555.

2 Effect Editing KeysBORD (Border) ButtonPress this button so that the key lamp lights when youwant to add a border to a wipe pattern. The color andwidth of the border can be adjusted with the BKNE-1011.For details about adjusting the border width and color, seeSection “2-2-4 Setting Effect Parameters” (page 2-9).

SOFT (Softness) ButtonPress this button so that the key lamp lights when youwant to add blur to the border line of a wipe pattern.The BKNE-1011 is used to correct blurring.

REV (Reverse) ButtonPress and light this button to reverse a wipe pattern.For details about reversing wipe patterns, see Section “2-2-3 Setting an Effect Pattern” (page 2-5).

1

2

3

4

5

6

1-4 Names and Functions of Parts

1-4-1 Console

* Keys With 2 or More Functions AssignedSome keys are marked for two functions. Pressing the key executes the function labeled on the second line of the key face.Holding down SHIFT and pressing the key executes the function labeled in small letters on the first line of the key face.When a key lamp is lit, the function indicated on the lower side of the key top is active.


Chapter 1 O

verview

MAN (Manual) keyTo manually perform a wipe or dissolve, press theWIPE or DISS button on the MAVE-F555’s EFFECToperation section, then press this button so that its keylamp lights. Moving the fader lever on the BKNE-1011 enables wipe and dissolve execution.

PRMTR (Parameter) keyPress to open the Effect Pattern Parameter Settingsscreen.

PATT key (SHIFT + PRMTR)Press to open the Effect Pattern NO. Settings screen,and then use the number keypad to enter the numbervalues to set the effect pattern numbers.

LOC (Location) key (SHIFT + MAN)Press to enable control and adjustment using the trackball of the XYZ position of the control effect.

3 Recall GroupIN keyPress to display in the information display area the INpoint data .

OUT keyPress to display OUT point data on the informationdisplay.

TOTAL keyPress to display the total duration of the edited materialin the information display.

DUR keyPress to display in the information display area theduration.

GO TO keyPress to jump to the edit point (IN or OUT point, or thestart edit point) currently shown in the informationdisplay area.

The following keys flash during operation. Press againto toggle them off.

SOF key (SHIFT + IN)Press to start the key flashing, and then use the GO TOkey to jump to the beginning of the file.

EOF key (SHIFT + OUT)Press to start the key flashing, and then use the GO TOkey to jump to the end of the file.

START key (SHIFT + TOTAL)Press to display in the information display area the editstart point .

SPEED key (SHIFT + DUR)Press to display in the information display area thecurrently selected DMC playback speed .

SCR GO TO (SHIFT + GO TO)Press to jump to the edit point currently displayed.

4 Data Edit GroupCLEAR keySelect data to delete, and then press this key to deleteit. To delete all edit data, hold down CLEAR and pressSHIFT.

LAST X keyPress this key to display the previous data entry, andthen press again to display the next entry. Press thiskey to toggle between the previous entry and the entryjust entered. If you make a mistake during edit pointentry, pressing this key allows you to restore theprevious editing point without making another entry .

MARK SPEED keyPress this key during DMC playback to mark the DMCplayback speed during edit. The speed at the time thekey is pressed is registered.

LAST EDIT key (SHIFT + LAST X)Press to recall the value of the last edit point executed.

5 Number keypad and Effect Pattern SelectionGroup

Wipe Pattern keysThe wipe pattern keys (the 9 keys marked with wipepatterns) are used as wipe pattern selection keys whileworking with effects on the MAVE-F555. To select awipe pattern, hold down the SHIFT key and press tolight the key and select the wipe pattern displayed onthe key.

Number keypadPress the PATT key (SHIFT + PRMTR) to enter thepattern number selection mode, and then use thenumber keys to enter values of the effect patterns thatyou want to recall. You can also use the number keysto enter directly IN and OUT points, the durationsettings, etc.

Marked Alphabetic keysUse these keys when you need to enter text to renamea file used on the MAVE-D555.For details about renaming files see “Renaming” (page 2-28).

[+] keyIncrements the entered time code.

[–] keyDecrements the entered time code.

F/TC keyPress the set the Frame or TC with the unit specified inthe scratchpad.


Chapter 1 O

verview

MENU key (SHIFT + [+])Opens the MENU screen.

T-SET key (SHIFT + [–])With the VTR, this functions as CTL, and with theMAV-555 it functions as TM1 PRESET.

T-TRACK key (SHIFT + F/TC)When the player deviates from the time track, press toreturn it to the target time track.

SCR-C key (SHIFT + 0)Clears one character of scratchpad data.

CTL/TC key (SHIFT + 00)Sets the CTL (with a VTR), TM1 or TM2 (with theMAV-555) used as the TC SOURCE for the currentlyselected device.

ENTER keyPress to enable the data entered in the scratchpad.

RETURN key (SHIFT + ENTER)Press to return to the normal edit mode after using thepattern number screen, viewing a menu, or using theparameter settings screen.

6 Control GroupPLAY keyPress to light this key and execute playback at standardspeed.

STILL keyPress to light this key and freeze a frame duringplayback.

REW keyPress to light this key and rewind.

FF keyPress to light this key and fast forward.

SHIFT keyHold down this key and then press another key toexecute the function in the first line of the keymarking.

SHTL keyRotate the search dial to the desired location, and thenexecute playback at the speed selected by the dial(shuttle mode).

JOG keyPress this key to jog the display at the playback speedselected by the rotated position of the search dial.

DMC keyPress and light this key to use the search dial toconduct DMC playback or to control playback speedduring DMC editing.

ALL STOP keyPress to halt all functions at the same time during anyoperation except backgrounding.

STBOF key (SHIFT + PLAY)With the VTR in the STOP mode, press this key toenter the standby mode.

EJECT key (SHIFT + STILL)Ejects a cassette from the VTR (unloads file if a harddisk is the targeted device).

STEP– key (SHIFT + REW)Press this key to step backward from the currentposition by the amount specified in the menu. Thisfunction is not available when a VTR is selected.

STEP+ key (SHIFT + FF)Press this key to step forward from the current positionby the amount specified in the menu. This function isnot available when a VTR is selected.

STOP key (SHIFT + SHTL)Press this key to halt forwarding.

Search dialRotate when you want to search for an editing pointduring playback. Rotate right to search forward androtate left to search backward.

1-4 Names and Functions of Parts


Chapter 1 O

verview

MOUSE/TRACK BALL F555 I/FLCD

CONTRASTAUDIO FADER PANEL

1-4-2 Rear View

1 AUDIO FADER PANEL connectorConnects the Editing Fader Panel BKNE-1011.

2 LCD CONTRASTAdjusts the LCD contrast.

3MOUSE/TRACK BALL connectorConnects a mouse or track ball.

4 F555 I/F connectorConnects the Editing Panel MAVE-F555.

1 2 3 4


Chapter 1 O

verview

CONTROL PANEL PANEL SELECT CHARACTERREAR FRONT 1 2 3 NONE OFF ON80TH

SETUPSELECT

COMPOSITE SDI

VIDEOINPUT REMOTER1

PORT SELECT

R2/P3

P1

P2

INPUTSDI

AES/EBU

ANALOG

CH1

CH1

PRESET

AUDIO INPUT / MONITOR SELECT

CH2 CH3 CH4

MONITOR L

R

METERPANEL

525

REMOTE

MENU

LOCAL

CONTROLPANEL

625 SETUP BANK

TOTAL /REMAIN

PROCESSCONTROL VIDEO

CHROMA

SET UP/BLACK

CHROMA/PHASE

PHONES

1 2 3

SYSTEM HDD

HELP

FULL /TIME

TC/UB TC TYPE

MENU

10

SET

0

CH2

PRESET

CH3

PRESET

CH4

PRESET

VIDEO/MENU

PRESET

REVSOFTBORDEDIT

LASTX

CLEAR

LOCMAN

PATTPRMTR

SOFIN

EOFOUT

STARTTOTAL

SPEEDDUR

T-TRACKF/TC

SCRGO TO

STBOFPLAY

STOPSHTL

EJECTSTILL

STEP-REW

STEP+FF

MENU+

SCR-C0

CTL/TC00

T-SET-

MARKSPEED


987

654

321

RETURNENTER


GHI JKL MNO _ / " @

ABC

, . : ; & # * ?

DEF ( ) [ ]

1

2

3

4

10

1

9

8

7

6

5

4

3

2

1

0

2 3 4 MKNOB

LEVER

INPUTMIX

1 23 4L R

10

9

8

7

6

5

4

3

2

1

0

10

9

8-10

-4-6-10-14

-20

-28

-40

-52-60-∞

7

6

5

4

3

2

1

0

1 2 3 4

MEMORY

CUT DISS WIPE TITLE AUDIO

REDOUNDO

V A1 A2 A3 A4

TRIM

MARKSPLIT

EFFECT

R

STORE +-

P1 P2 BG

PORT/FILE ASSIGN

DELFILE

NEWFILE

FILE

MARK OUTMARK IN

REPLAYPREVIEW

EXECUTE/REC

SHIFT

MAV VTR

RECORDER SEL BACK GROUND

AMIX

1-5 System Configuration Example

In the configuration above, the main feature of the MAV-555 is that it can take over the editing functionspreviously done with the BVE-series editor and conduct nonlinear editing (executing cut jumps, cut insertions,deletion, etc. with materials on the recorder). Such a configuration enables seamless operations when using theMAVE-D555 search dial to find edit points, when selecting effects, or when specifying edit points with theMAVE-F555 keys and allows smooth nonlinear editing.

Notes

• A VTR can be connected only to the REMOTE IN/OUT 1 (VTR) connector on the MAV-555.• Only the D555 I/F1 connector of the MAVE-F555 is enabled.

MAV-555: 2 input/2 output

VTR

BKNE-1011 MAVE-F555 MAVE-D555

MAV-555

R2

RS-422

MONITOR OUT

R1 P1

P2

REMOTESPARE

AUDIO FADER PANELRS-422

D555 I/F 1 F555 I/F

MOUSE/TRACK BALLTO MAV

CONTROLPANEL

LINE INPUT

Chapter 2 Operation 2-1 (E)

Chapter 2 O

peration

T-TRACKF/TC

MENU+

SCR-C0

CTL/TC00

T-SET-

987

654

321

RETURNENTER


GHI JKL MNO _ / " @

ABC

, . : ; & # * ?

DEF ( ) [ ]

2-1 Edit Point Operations

Before you perform any of the operations described below, make sure that the target port has been selected withthe MAVE-F555 PORT/FILE ASSIGN operation.

2-1-1 Setting Edit Data with theNumber Keypad

While using the MAVE-D555, you can use its numberkeypad to set the IN, OUT, and duration settings.

Specifying Edit Data with Number Keys

1 Press the IN, OUT, or DUR key for the data thatyou want to specify.

The pressed key lights and the current MAVE-D555 selections are shown in the informationdisplay area.

-or-

Press the START key (SHIFT + TOTAL) orSPEED key (SHIFT + DUR) for the data that youwant to specify.

The pressed key flashes and the current MAVE-D555 selections are shown in the informationdisplay area.

2 Press the number keys to enter the numeric values.

The entries are displayed in the informationdisplay area.

3 After the last entry, press the ENTER key.

The new entries are stored.

2-1-2 Confirming Edit Data (RECALL)Press the appropriate key of the Recall group whenyou need to confirm specified edit data. The dataspecified for the pressed key is displayed on the screenin the information display area.

Data to Confirm Key to Press

IN point data IN key

OUT point data OUT key

Total edits TOTAL key

Duration DUR key

Edit start points (START time) START key(SHIFT+TOTAL)

DMC playback speed settings SPEED key (SHIFT+DUR)

2-1-3 Changing Edit Data

When you need to change edit data, you can eitherclear the currently specified time code and set anotherone, or increase or reduce the current time code.

Changing the Time Code Displayed in theScratchpad

1 In the information display area, display the timecode that you want to change.

2 Use the number keys to enter a new time code intothe scratchpad.

3 Press the ENTER key to execute.

2

3

LOCMAN

PATTPRMTR

SOFIN

EOFOUT

STARTTOTAL

SPEEDDUR

SCRGO TO

STBOFPLAY

STOPSHTL

EJECTSTILL

STEP-REW

STEP+FF


T-TRACKF/TC

MENU+

SCR-C0

CTL/TC00

T-SET-

987

654

321

RETURNENTER


GHI JKL MNO _ / " @

ABC

, . : ; & # * ?

DEF ( ) [ ]

1 2

3

LOCMAN

PATTPRMTR

SOFIN

EOFOUT

STARTTOTAL

SPEEDDUR

SCRGO TO

Recall Group

2-2 (E) Chapter 2 Operation

Chapter 2 O

peration

Incrementing and Decrementing theCurrent Time Code

1 Press the key (IN, OUT, DUR) for the data thatyou want to change.

The pressed key lights and the current setting isshown in the information display area.

2 Press a number key to enter the amount of change.

For example, to reduce the current setting by 1second, press the minus key [–] on the keypad andthen press 1 then 00.

3 When you are finished, press the ENTER key.

The amount of change is reflected in the newsetting.

2-1-4 Jumping to an Edit Point(GO TO)

You can jump (cue up) to a desired edit point (IN,OUT point) or other point in a specified material.

Jumping to an Edit Point

1 Press a key in the Recall group to jump to thedesired point.

The data for the pressed key is shown in theinformation display area.

Jump Point Key to Press



Edit start point (START time) START key(SHIFT+TOTAL)

Start of file SOF key (SHIFT+IN)

End of file EOF key (SHIFT+OUT)

2 Press the GO TO key.

The jump is executed to the point selected in Step1. A still frame of the jump point is displayed onthe screen.

Note

If a jump destination is not specified in Step 1, thejump is executed to the first IN point after the GO TOkey is pressed.

Jumping to a Desired Point

1 Use the number keys on the keypad to enter thenumber of the time data for the desired jump point.

The entered number is displayed in the scratchpad.

2 Press the SCR GO TO key (SHIFT + GO TO).

The jump executes to the point specified in Step 1.

LOCMAN

PATTPRMTR

SOFIN

EOFOUT

STARTTOTAL

SPEEDDUR

T-TRACKF/TC

SCRGO TO

MENU+

SCR-C0

CTL/TC00

T-SET-

987

654

321

RETURNENTER


GHI JKL MNO _ / " @

ABC

, . : ; & # * ?

DEF ( ) [ ]

1 2

3

LOCMAN

PATTPRMTR

SOFIN

EOFOUT

STARTTOTAL

SPEEDDUR

SCRGO TO

STBOFPLAY

STOPSHTL

EJECTSTILL

STEP-REW

STEP+FF


1

2

LOCMAN

PATTPRMTR

SOFIN

EOFOUT

STARTTOTAL

SPEEDDUR

SCRGO TO

STBOFPLAY

STOPSHTL

EJECTSTILL

STEP-REW

STEP+FF


T-TRACKF/TC

MENU+

SCR-C0

CTL/TC00

T-SET-

987

654

321

RETURNENTER


GHI JKL MNO _ / " @

ABC

, . : ; & # * ?

DEF ( ) [ ]

1

2

2-1 Edit Point Operations


Chapter 2 O

peration

2-1-5 Clearing Edit Data (CLEAR)

When new data is specified it automatically replacesthe previous data, but if you want to delete datawithout replacing it with new data follow theprocedure below.

Clearing Data

1 Press the key in the Recall group with the data thatyou want to clear.

The data of the pressed key is displayed in theinformation display area.

Data to Delete Key to Press



Duration DUR key

DMC playback speed setting SPEED key (SHIFT+DUR)

2 Press the CLEAR key.

The specified data is cleared.

Clearing all Data

To clear all data, hold down the SHIFT key and thenpress the CLEAR key.

2-1-6 Edit Totals

An editing session may require repeated editing ofmany parts of successive materials. After editing onthe MAV-555, you can automatically calculate thetotal duration of material edited during the previoussession and display the total in the information displayarea.

Changing the Edit Start Time

With no other special settings on the MAV-555, thetime code setting specified for “SHOW TC” on theMAV-555 Expansion Menu item 321: LINEAR EDITNEW FILE is used as the starting point for calculatingthe duration of the edited material. Follow theprocedure below to change the edit starting point.

1 In the Recall group press START (SHIFT +TOTAL).

The current selected start point is displayed in theinformation area display of the MAVE-D555.

2 Use the number keys to enter the starting point.

3 Press the ENTER key.

The value for the starting point specified in Step 2is saved.

Confirming the Total Edited Duration

To confirm the duration of the edited material from thestarting point to the present time, press the TOTALkey. The total is displayed in the information displayarea of the MAVE-D555.

LOCMAN

PATTPRMTR

SOFIN

EOFOUT

STARTTOTAL

SPEEDDUR

SCRGO TO

STBOFPLAY

STOPSHTL

EJECTSTILL

STEP-REW

STEP+FF


EDITLAST

XCLEAR MARK

SPEED

T-TRACKF/TC

MENU+

SCR-C0

CTL/TC00

T-SET-

987

654

321

RETURNENTER


GHI JKL MNO _ / " @

ABC

, . : ; & # * ?

DEF ( ) [ ]

1

2

LOCMAN

PATTPRMTR

SOFIN

EOFOUT

STARTTOTAL

SPEEDDUR

SCRGO TO

STBOFPLAY

STOPSHTL

EJECTSTILL

STEP-REW

STEP+FF


T-TRACKF/TC

MENU+

SCR-C0

CTL/TC00

T-SET-

987

654

321

RETURNENTER


GHI JKL MNO _ / " @

ABC

, . : ; & # * ?

DEF ( ) [ ]12

3


Chapter 2 O

peration

2-2 Operations for Each Function

Notes

• After the DMC playback speed is set once, the speedspecified for DMC playback is used on the specifiedplayer for subsequent editing sessions. In order toplayback at standard playback speed, erase the DMCplayback speed settings by following the proceduredescribed in “Deleting the DMC Playback Setting”(page 2-5).

• After verifying the speed setting with the SPEED key(SHIFT + DUR) on the RECALL group, you canchange the setting with the numeric keys.

Controlling Playback Speed During Editing

Use the search dial to vary the speed continuouslyduring an editing session using DMC playback.

2-2-1 DMC Editing

You can perform DMC editing when using the MAV-555 or a player that is equipped with the DT function. Inorder to perfrom DMC editing, you must specify beforehand the DMC playback speed on the Player. The specifiedspeed becomes the initial DMC playback for editing. Advancing to the IN points during editing is performed at theinitial speed specified for DMC playback.

Specifying the DMC Playback Speed

1 Use the FILE/PORT ASSIGN operation on theMAVE-F555 to select the Player port.

The pressed key lights.

2 On the MAVE-D555 press the DMC key.

3 Rotate the search dial to the desired playbackspeed setting.

4 On the MAVE-D555 press the MARK SPEEDkey.

The key lights and the speed specified in Step 3 isselected as the DMC playback speed.

REVSOFTBORDEDIT

LASTX

CLEAR

LOCMAN

PATTPRMTR

SOFIN

EOFOUT

STARTTOTAL

SPEEDDUR

T-TRACKF/TC

SCRGO TO

STBOFPLAY

STOPSHTL

EJECTSTILL

STEP-REW

STEP+FF

MENU+

SCR-C0

CTL/TC00

T-SET-

MARKSPEED


987

654

321

RETURNENTER


GHI JKL MNO _ / " @

ABC

, . : ; & # * ?

DEF ( ) [ ]

1 2 3 4

MEMORY


REDOUNDO

V A1 A2 A3 A4

TRIM

MARKSPLIT

EFFECT

R

STORE +-

P1 P2 BG

PORT/FILE ASSIGN

DELFILE

NEWFILE

FILE

MARK OUTMARK IN

REPLAYPREVIEW

EXECUTE/REC

SHIFT

MAV VTR


AMIX

MAVE-F555 MAVE-D555

1

2

4

3


Chapter 2 O

peration

1 After passing the IN point, rotate the search dial tocontrol the speed.

Confirming the DMC Playback Speed

Press the SPEED key (SHIFT + DUR) in the Recallgroup. The selected speed is shown as a percent in theinformation display area.

Deleting the DMC Playback Setting

1 Press the CLEAR key. The pressed key lights.

2 Press the MARK SPEED key.

The DMC mode is canceled and the specifiedDMC playback speed is erased.

2-2-2 Voice Over Editing

A voice over edit with audio can be added to the end ofan edited material. It is also possible to add video inthe same manner. Before you can perform this voiceover editing, it must be set up with the MAVE-D555 inthe normal mode or the pre-read mode.

Connection Example

1 Hold down the SHIFT key and press the AUDIOkey on the MAVE-F555’s EFFECT operationsection.

The AUDIO key flashes and the unit enters thevoice over mode.

When adding video, press the MAVE-F555channel specification V key until it lights.

2 On the Recorder specify the interval where youwant to add the voice over edit.

3 Press the EXECUTE/REC key to execute.

Note

To return to the normal edit mode, press and holddown the SHIFT and press the AUDIO key on theMAVE-555’s EFFECT operation section.

2-2-3 Setting an Effect Pattern

This section describes how to specify an effect patternduring editing operations. Please keep in mind thefollowing important points regarding editing withspecial effects:• Special effects can be used during editing only when

editing with the MAVE-F555 in the OVERWRITEmode.

• To return to the normal editing mode from the effectpattern selection mode, press the RETURN key(SHIFT + ENTER).

• AUDIO is normal set for “Fade”.For more details about the effect patterns that can be used,refer to the BKMA-560 operation manual.

Editing using special effects with the MAVE-D555 isdifferent from previous A/B Roll Editing. Editing canbe executed by selecting only one port for the Player.Editing can be performed with an image resemblingthat of the previous Pre-Read editing method.

Previous A/B Roll EditingIN

IN

IN

OUT

OUT

OUT

IN OUT

PLAYER 1

PLAYER 2

RECORDER(Material BeforeEdit)

RECORDER(Material After Edit)

Effect Editing with MAVE-D555

IN OUT

IN

IN OUT

PLAYER

RECORDER(Material BeforeEdit)

RECORDER(Material After Edit)

VIDEO IN COMPOSITE

IN ——— R1 ——— OUT

IN ——— R2 ——— OUT

R1 R2 SYSTEM

REFERENCE

IN OUT

VIDEO OUT COMPOSITE

A ——— P1 ——— B

A ——— P2 ——— B

TIME CODE IN

A ——— P3 ——— B

AUDIO IN (AES/EBU)

CH1/2 —— R1 —— CH3/4

CH1/2 —— R2 —— CH3/4

VS BUS

IN OUT

REMOTE PARALLEL I/O (50P) ETHER CONTROL PANEL MONITOR OUT

P1 P2 P3

TIME CODE OUT

SERIAL V/A IN

—— R1 ——

SERIAL V/A(SUPER)

ANALOGCOMPOSITE

(SUPER)

—— R2 ——

SPARE

OPTION

AUDIO OUT (AES/EBU)

A —— P1 —— B

A —— P2 —— B

A —— P3 —— B

SERIAL V/A OUT REMOTE AUDIO I/F

A —— P1 —— B IN1(R1)

A —— P2 —— B

A —— P3 —— B

IN2(P1)

IN3(R2/P3)

IN4(P2)

IN/OUT1(VTR) IN/OUT2(VTR) SPARE

Digital oranalogaudio input.

Audio Mixer

Digital or analog audiooutput.

Audio Source


Chapter 2 O

peration

Selecting a Wipe Pattern from a Design and Executing it

7 On the MAVE-D555 hold down the SHIFT key,and then press the key for the wipe pattern that youwant to select. The pressed key lights.

The pattern registered for the pressed key isselected and the transition time of the selectedpattern is displayed in the information display areaof the MAVE-D555.

8 Use the number keys to enter the duration time inthe scratchpad, and then press the ENTER key.

The maximum value that can be set for thetransition time is 998 frames.

9 On the MAVE-F555 press the EXECUTE/RECkey to execute the edit.

MAVE-F555 MAVE-D555

REVSOFTBORDEDIT

LASTX

CLEAR

LOCMAN

PATTPRMTR

SOFIN

EOFOUT

STARTTOTAL

SPEEDDUR

T-TRACKF/TC

SCRGO TO

STBOFPLAY

STOPSHTL

EJECTSTILL

STEP-REW

STEP+FF

MENU+

SCR-C0

CTL/TC00

T-SET-

MARKSPEED


987

654

321

RETURNENTER


GHI JKL MNO _ / " @

ABC

, . : ; & # * ?

DEF ( ) [ ]

1 2 3 4

MEMORY


REDOUNDO

V A1 A2 A3 A4

TRIM

MARKSPLIT

EFFECT

R

STORE +-

P1 P2 BG

PORT/FILE ASSIGN

DELFILE

NEWFILE

FILE

MARK OUTMARK IN

REPLAYPREVIEW

EXECUTE/REC

SHIFT

MAV VTR


AMIX

1 Press the MAVE-F555 [ ] key to enter theOVERWRITE mode.

2 Use the FILE/PORT ASSIGN operation on theMAVE-F555 to select the Player.

3 Select the IN and OUT points for the intervalwhere you want to place the effect result.

4 Use the FILE/PORT ASSIGN operation on theMAVE-F555 to select the Recorder.

5 Rotate the search dial on the MAVE-D555 toselect the IN point where the result of the effectwill start.

6 In the EFFECT operation section on the MAVE-F555, press the WIPE key.

The pressed key lights.

1

3, 5

9

2, 4

67

8

3, 5



Chapter 2 O

peration

Notes

• During editing with selected effect patterns of picturein a picture and other animation systems, the portionbefore the transition time from the OUT point alsotakes time.

• During editing with a specified mosaic effect pattern,the Player interval specifications in Step 2 and Step 3are not required. Effect patterns that do not requirespecification of the Player interval are listed below.

Effect Pattern Pattern Number

Mosaic 1001,1011,1015,1016,1017,1018

Still Mirror 1020,1021,1022,1023,1024,1025,1026,1027

Y&C Modify 1030,1033,1040,1043,1046,1050,1055,1056,1057,1058

Strobe, Cinema 1065,1066,1067

Multi Screen 1240,1241

Real Paint 1280,1281,1282,1283

Stained Glass 1285,1286,1287,1288

Executing in the Direction Opposite Wipe

1 Execute the procedure for “Selecting a WipePattern from a Design and Executing it” as far asStep 8 (page 2-6).

2 Press the REV button in the MAVE-D555operation section. The pressed button lights.


Editing with the Dissolve Effect


2 Press the DISS key in the MAVE-F555 EFFECToperation section. The pressed key lights.

3 Use the number keys to enter the duration into thescratchpad and press the ENTER key.



Chapter 2 O

peration

Setting the Number for an Effect Pattern

4 On the MAVE-D555 after pressing the RETURNkey (SHIFT + ENTER) to enter the effect modeand then returning to the normal mode, thetransition time is shown in the information displayarea of the MAVE-D555.

5 Use the number keypad to enter the transition timein the scratchpad, and then press the ENTER key.


MAVE-F555 MAVE-D555


2 On the MAVE-D555 press the PATT key (SHIFT+ PRMTR) to enter the pattern number selectionmode. The PATT key flashes.

On the monitor the EE image is output, and theBKNE-1011 transition lever is enabled.

3 Use the number keypad to enter the effect numberin the scratchpad, and then press the ENTER key.

If an enabled pattern number is entered, thatpattern number is reflected. If an disabled patternnumber is entered, the number the largest numberclose to the entered number is reflected.

You can also set the number by using the minus [–]and [+] keys on the MAVE-F555.

6

REVSOFTBORDEDIT

LASTX

CLEAR

LOCMAN

PATTPRMTR

SOFIN

EOFOUT

STARTTOTAL

SPEEDDUR

T-TRACKF/TC

SCRGO TO

STBOFPLAY

STOPSHTL

EJECTSTILL

STEP-REW

STEP+FF

MENU+

SCR-C0

CTL/TC00

T-SET-

MARKSPEED


987

654

321

RETURNENTER


GHI JKL MNO _ / " @

ABC

, . : ; & # * ?

DEF ( ) [ ]

1 2 3 4

MEMORY


REDOUNDO

V A1 A2 A3 A4

TRIM

MARKSPLIT

EFFECT

R

STORE +-

P1 P2 BG

PORT/FILE ASSIGN

DELFILE

NEWFILE

FILE

MARK OUTMARK IN

REPLAYPREVIEW

EXECUTE/REC

SHIFT

MAV VTR


AMIX

3

2 3, 5

4



Chapter 2 O

peration

2-2-4 Setting Effect Parameters

Note

In order to set an effect pattern, the Editing FaderPanel BKNE-1011 is required.For details about the Editing Fader Panel, see section “2-4Using the MAVE-D555 with the Editing Fader Panel” (page2-29).

Before you select an effect pattern in order to blur thepattern at the edges, or to add a border to the edges,you should first select the pattern and then display it onthe screen.

MAVE-D555 BKNE-1011

REVSOFTBORDEDIT

LASTX

CLEAR

LOCMAN

PATTPRMTR

SOFIN

EOFOUT

STARTTOTAL

SPEEDDUR

T-TRACKF/TC

SCRGO TO

STBOFPLAY

STOPSHTL

EJECTSTILL

STEP-REW

STEP+FF

MENU+

SCR-C0

CTL/TC00

T-SET-

MARKSPEED


987

654

321

RETURNENTER


GHI JKL MNO _ / " @

ABC

, . : ; & # * ?

DEF ( ) [ ]

1

2

3

4

10

1

9

8

7

6

5

4

3

2

1

0

2 3 4 MKNOB

LEVER

INPUTMIX

1 23 4L R

10

9

8

7

6

5

4

3

2

1

0

10

9

8-10

-4-6-10-14

-20

-28

-40

-52-60-∞

7

6

5

4

3

2

1

0

2

3

Displaying the Borders on the Screen

1 Referring the previous sections, “Selecting a WipePattern from a Design and Executing it”, (page 2-6), and “Setting the Number for an Effect Pattern”(page 2-8), assign an edit point to the effect andselect the effect pattern.

2 On the MAVE-D555 press the PRMTR key. Thekey lights and the machine enters the parametersetting mode.

3 Use the transition lever on the BKNE-1011 tomanually display the border of the effect pattern onthe screen.

Enabling Soft Edge and Border Edge

In order to enable the soft edge and border edgefeatures, in the MAVE-D555 Effect Group, press theSOFT button to enable the soft border, or press theBORD button to enable the border edge.The pressed button lights.


Chapter 2 O

peration

Specifying an Effect Parameter

1 Press the PRMTR key.

The menu opens in the information display area onthe screen.

2 Use the number keys to enter the number of themenu.

To advance to the next menu page, press the [+]key or the [–] key on the MAVE-F555.

1 Patt Adj 2 EDGE

3 BDR MAT 4 INT V

The following items are displayed on the menu:(Page 1)1: Patt Adj 2: EDGE3: BDR MAT 4: INT V

(Page 2)5: Light 6: Super BG7: DSK 8: DSK MAT

(Page 3)9: TITLE +: LUM-: CRK

3 Select the desired item. The machine enters theparameter mode.

The parameters order 1 to 4 from the leftcorrespond to settings 1 to 4 on the knob of theBKNE-1011. Use the knob of the BKNE-1011 toset the parameter selections for the MAVE-D555.

Note

To clear a selected parameter, after entering theparameter setting mode in Step 3, press the CLEARkey on the MAVE-D555. The corresponding key foreach parameter flashes on the MAVE-D555 numberkeypad. Press the number for the registered pattern thatyou want to clear. After you press the key, the factorydefault setting for the key is restored.

REVSOFTBORDEDIT

LASTX

CLEAR

LOCMAN

PATTPRMTR

SOFIN

EOFOUT

STARTTOTAL

SPEEDDUR

T-TRACKF/TC

SCRGO TO

STBOFPLAY

STOPSHTL

EJECTSTILL

STEP-REW

STEP+FF

MENU+

SCR-C0

CTL/TC00

T-SET-

MARKSPEED


987

654

321

RETURNENTER


GHI JKL MNO _ / " @

ABC

, . : ; & # * ?

DEF ( ) [ ]

1

2

3

4

10

1

9

8

7

6

5

4

3

2

1

0

2 3 4 MKNOB

LEVER

INPUTMIX

1 23 4L R

10

9

8

7

6

5

4

3

2

1

0

10

9

8-10

-4-6-10-14

-20

-28

-40

-52-60-∞

7

6

5

4

3

2

1

0

MAVE-D555 BKNE-1011

12

3



Chapter 2 O

peration

Conducting Manual Transition

3 Execute the edit.

The transition part of the effect is enabled byoperation of the transition lever on the BKNE-1011. Use the lever to select the desired transition.

However, the AUDIO transition is the transitiontime entered in the scratchpad.

1 Select the effect pattern.

2 Press the MAN key.

The key lights and the machine enters the manualtransition enabled status.

To release the machine from this status, on theMAVE-F555 press the CUT key, the DISS key, orthe WIPE key.

REVSOFTBORDEDIT

LASTX

CLEAR

LOCMAN

PATTPRMTR

SOFIN

EOFOUT

STARTTOTAL

SPEEDDUR

T-TRACKF/TC

SCRGO TO

STBOFPLAY

STOPSHTL

EJECTSTILL

STEP-REW

STEP+FF

MENU+

SCR-C0

CTL/TC00

T-SET-

MARKSPEED


987

654

321

RETURNENTER


GHI JKL MNO _ / " @

ABC

, . : ; & # * ?

DEF ( ) [ ]

1

2

3

4

10

1

9

8

7

6

5

4

3

2

1

0

2 3 4 MKNOB

LEVER

INPUTMIX

1 23 4L R

10

9

8

7

6

5

4

3

2

1

0

10

9

8-10

-4-6-10-14

-20

-28

-40

-52-60-∞

7

6

5

4

3

2

1

0

MAVE-D555 BKNE-1011

2

3


Chapter 2 O

peration

2-2-5 Using a Track Ball

A track ball can be attached to the MAVE-D555 and used to control mosaics and other effect patterns for whichXYZ coordinates can be adjusted. However, pointing device such as a mouse with a wheel is required in order toadjust the Z coordinate.

5 Execute the edit.

During PREVIEW, you can use a pointing devicesuch as a track ball to change the position and sizeof the pattern. The changes are recorded duringPREVIEW.

Notes

• To switch off the “LOC” display at Step 3, press theLOC key (SHIFT + MAN).

• When the effect pattern moves off-screen uponadjusting the XYZ coordinates, you can return it toscreen center by pressing the CLEAR key on theMAVE-D555. When the key lamp lights, left-clickthe pointing device such as a track ball.

1 On the MAVE-D555 press the PATT key (SHIFT+ PRMTR).

The PATT key flashes and the machine enters thepattern number selection mode.

2 Select the effect pattern for XY (or XYZ)adjustment.

3 On the MAVE-D555 press the LOC key (SHIFT +MAN).

“LOC” is displayed in the information display areaand the XYZ coordinates can now be controlled.

4 On the MAVE-D555 press the RETURN key(SHIFT + ENTER) to return to the normal mode.

REVSOFTBORDEDIT

LASTX

CLEAR

LOCMAN

PATTPRMTR

SOFIN

EOFOUT

STARTTOTAL

SPEEDDUR

T-TRACKF/TC

SCRGO TO

STBOFPLAY

STOPSHTL

EJECTSTILL

STEP-REW

STEP+FF

MENU+

SCR-C0

CTL/TC00

T-SET-

MARKSPEED


987

654

321

RETURNENTER


GHI JKL MNO _ / " @

ABC

, . : ; & # * ?

DEF ( ) [ ]

1 2 3 4

MEMORY


REDOUNDO

V A1 A2 A3 A4

TRIM

MARKSPLIT

EFFECT

R

STORE +-

P1 P2 BG

PORT/FILE ASSIGN

DELFILE

NEWFILE

FILE

MARK OUTMARK IN

REPLAYPREVIEW

EXECUTE/REC

SHIFT

MAV VTR


AMIX

MAVE-F555 MAVE-D555

5

3 1

4



Chapter 2 O

peration

2-2-6 Registering Effects

Frequently used effects (effect patterns, transition times, and other parameter settings) can be saved on the MAVE-F555. Follow the procedure below to register effects with the MEMORY key on the MAVE-F555.

4 In the FILE/PORT ASSIGN group of the MAVE-F555, hold down the STORE key, and then pressany MEMORY key from 1 to 4.

The effect selected in Steps 2 and 3 is stored underthe MEMORY key that you press.

Notes

• Effects stored on the MAV-555 are shared in all ofthe MAV-555 setup menu banks. Effects cannot beregistered individually for separate banks.

• Registered effects are cancelled if the MAV-555 isleft unused for an extended period of time after powerit off.

1 On the MAVE-D555 press the PRMTR key or thePATT key (SHIFT + PRMTR).

2 Follow the procedure described in section “2-2-3Setting an Effect Pattern” (page 2-5) to select theeffect that you want to register.

3 Follow the procedure described in “Specifying anEffect Parameter” (page 2-10) to specify thepattern.At the same time, set the transition time.

MAVE-F555 MAVE-D555

REVSOFTBORDEDIT

LASTX

CLEAR

LOCMAN

PATTPRMTR

SOFIN

EOFOUT

STARTTOTAL

SPEEDDUR

T-TRACKF/TC

SCRGO TO

STBOFPLAY

STOPSHTL

EJECTSTILL

STEP-REW

STEP+FF

MENU+

SCR-C0

CTL/TC00

T-SET-

MARKSPEED


987

654

321

RETURNENTER


GHI JKL MNO _ / " @

ABC

, . : ; & # * ?

DEF ( ) [ ]

1 2 3 4

MEMORY


REDOUNDO

V A1 A2 A3 A4

TRIM

MARKSPLIT

EFFECT

R

STORE +-

P1 P2 BG

PORT/FILE ASSIGN

DELFILE

NEWFILE

FILE

MARK OUTMARK IN

REPLAYPREVIEW

EXECUTE/REC

SHIFT

MAV VTR


AMIX

14


Chapter 2 O

peration

Recalling Registered Effects

1 On the MAVE-D555 press the PRMTR key orPATT key (SHIFT + PRMTR).

2 Press one of MAVE-F555 MEMORY keys 1 to 4,depending on the effect to be recalled.

The current effect is replaced with the effectrecalled with the MEMORY key, and all the otherparameters (transition time, etc.) are also enabled.

MAVE-F555 MAVE-D555


2-2-7 Inserting Text and Graphics

Title Key

parameter settings menu 9: TITLE, “SRC”(SOURCE) setting.

• It is necessary to set the KEY signal type in effectparameter settings menu 9: TITLE, “KEY” setting.

• The BKMA-560 Option Board must be installed inthe MAV-555.

• Editing can be done only on the recorder port.• Editing can be done only in the OVERWRITE

mode.• This procedure cannot be performed with the

MAV-777.

You can insert text and graphics while applyingeffects.

Notes

• You can either input the external video signal tothe left SPARE terminal on the MAV-555connector panel (when using the MAV-555A or theMAV-555SS in SD mode, use the DSK IN VIDEOterminal), or make the internal MAV-555 player aKEY signal. You can make this setting in effect

REVSOFTBORDEDIT

LASTX

CLEAR

LOCMAN

PATTPRMTR

SOFIN

EOFOUT

STARTTOTAL

SPEEDDUR

T-TRACKF/TC

SCRGO TO

STBOFPLAY

STOPSHTL

EJECTSTILL

STEP-REW

STEP+FF

MENU+

SCR-C0

CTL/TC00

T-SET-

MARKSPEED


987

654

321

RETURNENTER


GHI JKL MNO _ / " @

ABC

, . : ; & # * ?

DEF ( ) [ ]

1 2 3 4

MEMORY


REDOUNDO

V A1 A2 A3 A4

TRIM

MARKSPLIT

EFFECT

R

STORE +-

P1 P2 BG

PORT/FILE ASSIGN

DELFILE

NEWFILE

FILE

MARK OUTMARK IN

REPLAYPREVIEW

EXECUTE/REC

SHIFT

MAV VTR


AMIX

21


Chapter 2 O

peration


2 Use the FILE/PORT ASSIGN operation on theMAVE-F555 to select the Player.

3 Select the interval (IN and OUT points) where youwant to insert text or graphics in the editedmaterial.


5 Using the MAVE-D555 search dial, search for thepoint where you want to begin inserting text andgraphics, and then specify the IN point.

6 Select the effect pattern and transition time to usewhen inserting text and graphics.A transition is used at the IN and OUT pointswhere text and graphics are inserted.

7 Press the TITLE key in the EFFECT operationsection on the MAVE-F555.The pressed key lights.

8 Press the REPLAY/PREVIEW key on the MAVE-F555, if desired, to preview.

9 Press the EXECUTE/REC key on the MAVE-F555to execute editing.The input signal is inserted and editing is finished.When the TITLE key is lit and you want to finishthis operation without inserting text or graphics,press the TITLE key again to turn it off.

MAVE-F555 MAVE-D555

2, 4

1

REVSOFTBORDEDIT

LASTX

CLEAR

LOCMAN

PATTPRMTR

SOFIN

EOFOUT

STARTTOTAL

SPEEDDUR

T-TRACKF/TC

SCRGO TO

STBOFPLAY

STOPSHTL

EJECTSTILL

STEP-REW

STEP+FF

MENU+

SCR-C0

CTL/TC00

T-SET-

MARKSPEED


987

654

321

RETURNENTER


GHI JKL MNO _ / " @

ABC

, . : ; & # * ?

DEF ( ) [ ]

1 2 3 4

MEMORY


REDOUNDO

V A1 A2 A3 A4

TRIM

MARKSPLIT

EFFECT

R

STORE +-

P1 P2 BG

PORT/FILE ASSIGN

DELFILE

NEWFILE

FILE

MARK OUTMARK IN

REPLAYPREVIEW

EXECUTE/REC

SHIFT

MAV VTRA

MIX


9

7

8

6

5


Chapter 2 O

peration

Necessary Effect Parameter Settings

To be able to specify the source for text and graphicsthat you want to insert, it is necessary to make thefollowing settings in the screen that appears afterpressing the MAVE-D555 PRMTR key.

• KEY signal settings(1) In effect parameter settings menu 9: TITLE, set

“KEY” to “LUM” (Luminance key) or “CRK”(Chroma key).

(2) In effect parameter settings menu 9: TITLE,“SRC”, set the source of the KEY signalspecified in (1) to “K-IN” (external video KEYsignal) or to “SELF” (the KEY signal itself).If you selected “CRK” in (1) above, you canonly select “SELF”.

(3) If necessary, in effect parmeter settings menu 9:TITLE, set “MASK” (KEY signal mask ON/OFF) and “INV” (masked area turnover ON/OFF), etc. Also, in effect parameter menu +:“LUM” (Luminance key) or -: “CRK” (Chromakey) set “Clip” (clip adjustment), “Gain” (gainadjustment), “INV” (luminance turnover ON/OFF), and “DNST” (image density).

Note

If “KEY” is set to “CRK”, it is also necessaryto adjust the “Hue” and “Ang” of the color tocut.

• FILL signal settings(1) In effect parameter settings menu 9: TITLE, set

“KEY” to “LUM” (Luminance key) or “CRK”(Chroma key).

(2)Depending on the setting in (1), perform thefollowing settings.- If “KEY” is set to “LUM”, in menu +: LUM,

set “FILL” to “VID” (player internal BUSsignal) or to “BDRM” (border MATT).

- If “KEY” is set to “CRK”, in menu -: CRK,set “FILL” to “VID” (player internal BUSsignal) or to “BDRM” (border MATT).

Setting Examples

If the Luminance key and Fill signals are input to therecorder from an external source, and inserted as titleinformation, make the following settings.

Menu Content9: TITLE “KEY” = “LUM”

“SRC” = “K-IN”+: LUM “FILL” = “VID”

See Section “2-2-8 Editing with the Player BUS” (page2-19), and set MEMORY key 2: AUX for the BUS.For details about parameter settings, see “TITLE Key,Downstream Key, and Player BUS Setting Example” (pageA-7).



Chapter 2 O

peration



3 Select the interval (IN and OUT points) where youwant to insert text or graphics in the editedmaterial.

4 Press the TITLE key while pressing the SHIFT keyin the EFFECT operation section on the MAVE-F555.

The pressed key blinks and “DSK” issuperimposed on the display.

T R 0 1 : 0 0 D S K

Downstream Key (DSK)

The DSK (Downstream key) can be used to insert textand graphics into cuts to which effects have beenapplied and editing is finished.

Notes


• The DSK KEY signal must be applied to the right-side SPARE terminal on the MAV-555 connector

panel. (With the MAV-555SS in SD mode or theMAV-555A, the DSK IN KEY terminal.) The DSKVIDEO signal may be applied to the left-side MAV-555 SPARE terminal (with the MAV-555SS in SDmode or the MAV-555A, the DSK IN VIDEOterminal), but editing is possible even if it is not. Inthis case, the “FILL” in the Effect Parameters menuitem 7: DSK must to be set to DSKM.

• Editing can be done only on the recorder port.• Editing can be done only in the OVERWRITE mode.• This procedure cannot be performed with the MAV-

777.

MAVE-F555 MAVE-D555

REVSOFTBORDEDIT

LASTX

CLEAR

LOCMAN

PATTPRMTR

SOFIN

EOFOUT

STARTTOTAL

SPEEDDUR

T-TRACKF/TC

SCRGO TO

STBOFPLAY

STOPSHTL

EJECTSTILL

STEP-REW

STEP+FF

MENU+

SCR-C0

CTL/TC00

T-SET-

MARKSPEED


987

654

321

RETURNENTER


GHI JKL MNO _ / " @

ABC

, . : ; & # * ?

DEF ( ) [ ]

1 2 3 4

MEMORY


REDOUNDO

V A1 A2 A3 A4

TRIM

MARKSPLIT

EFFECT

R

STORE +-

P1 P2 BG

PORT/FILE ASSIGN

DELFILE

NEWFILE

FILE

MARK OUTMARK IN

REPLAYPREVIEW

EXECUTE/REC

SHIFT

MAV VTRA

MIX


4

1

6

52

7


Chapter 2 O

peration

5 Use the keypad keys to enter the transition time onthe scratchpad, and press the ENTER key.


7 Press the EXECUTE/REC key on the MAVE-F555to execute editing.The input signal is inserted and editing is finished.When the TITLE key is blinking and you want tofinish this operation without inserting text orgraphics, press the TITLE key again while pressingthe SHIFT key.

Notes• When text and graphics are inserted into an interval

where a cut point exists, any existing information atthat point is cleared as the new information isinserted. We therefore recommend inserting afterediting is finished.

• After pressing the PRMTR key to select a parameter,press the TITLE key while pressing the SHIFT key sothat adjustment can be made while monitoring theactual parameter. Pressing the TITLE key whilepressing the SHIFT key again reverts to the formerstate.

• When pressing the TITLE key while pressing theSHIFT key to set a downstream key, you can pressthe MAN key on this unit (so that it is lit) to enablemanual downstream key switching during the intervalmentioned in step 3. The downstream key switcheson and off each time you press the TITLE key whilepressing the SHIFT key.

Necessary Effect Parameter Settings

To be able to specify the source for text and graphicsthat you want to insert, it is necessary to make thefollowing settings when pressing the MAVE-D555PRMTR key.

• KEY signal settings(1) In effect parameter settings menu 7: DSK, set

“INV” “ON” or “OFF” to activate or deactivatethe KEY signal turnover.

(2) If a FILL signal is not input to the MAV-555,set “FILL” to “DSKM”.

(3) If necessary, adjust “DNST” (DSK density).

• FILL signal settings(1) In effect parameter settings menu 7: DSK, set

“FILL” to “V-IN” (external VTR signal) or“DSKM” (BKMA-560 built-in Internal Videosignal).

(2) If necessary, when “DSKM” is set adjust colorsin effect parameter settings menu 8: DSK MAT.For details about parameter settings, see “TITLEKey, Downstream Key, and Player BUS SettingExample” (page A-7).



Chapter 2 O

peration

2-2-8 Editing with the Player BUS



3 Using the MAVE-D555 search dial, search for editpoints, and then specify the IN and OUT points.

4 Select the effect pattern and transition time.(It is also possible to perform cut editing.)

MAVE-F555 MAVE-D555

REVSOFTBORDEDIT

LASTX

CLEAR

LOCMAN

PATTPRMTR

SOFIN

EOFOUT

STARTTOTAL

SPEEDDUR

T-TRACKF/TC

SCRGO TO

STBOFPLAY

STOPSHTL

EJECTSTILL

STEP-REW

STEP+FF

MENU+

SCR-C0

CTL/TC00

T-SET-

MARKSPEED


987

654

321

RETURNENTER


GHI JKL MNO _ / " @

ABC

, . : ; & # * ?

DEF ( ) [ ]

1 2 3 4

MEMORY


REDOUNDO

V A1 A2 A3 A4

TRIM

MARKSPLIT

EFFECT

R

STORE +-

P1 P2 BG

PORT/FILE ASSIGN

DELFILE

NEWFILE

FILE

MARK OUTMARK IN

REPLAYPREVIEW

EXECUTE/REC

SHIFT

MAV VTRA

MIX


1

2

7

5

6

4

3

Section “TITLE Key” (page 2-14) describes how toedit and apply effects when the MAV-555 internalplayer port is assigned to the BUS signal. This sectiondescribes how to change and edit the external VIDEOsignal input to the player BUS from the optionalBKMA-560 built-in Internal Video, or to the leftSPARE terminal on the MAV-555 connector panel(with the MAV-555A or MAV-555SS in SD mode, the

DSK IN VIDEO terminal).

Notes


• The preset audio of the MAVE-F555 channels ismuted.

• This operation is not possible with the MAV-777.

5 In the MAVE-F555 EFFECT operation section,press the MEMORY key while pressing the key(CUT, DISS, WIPE) corresponding to the effectpattern that you selected in Step 4.The BUS signal is selected.

• MEMORY key 1: The MAV-555 internal playeror external VTR is selected (P1, R, P2, or BG).

• MEMORY key 2: The signal input at the DSK INVIDEO terminal of the MAV-555SS in SD modeor the MAV-555A (with the MAV-555, the leftSPARE terminal) is selected (AUX).

• MEMORY key 3: The optional BKMA-560 built-in Internal Video signal is selected (MATT).


Chapter 2 O

peration


7 Press the EXECUTE/REC key on the MAVE-F555to execute editing.The input signal is inserted and editing is finished.

NoteDetailed information about the recorder and playerports is summarized and superimposed on the display.It is also possible to confirm the direction of the BUSsignal.For details about parameter settings, see “TITLE Key,Downstream Key, and Player BUS Setting Example” (pageA-7).

Display Example

D I S T R 0 1 : 0 0S

U n d

R [ R : M A V R P ]

P [ P : M A V P 11 ]

I N V 1 2 3 40 0 : 1 0 : 0 1 : 0 0O U T 0 0 : 1 0 : 0 3 : 0 0D U 0 0 : 0 0 : 0 2 : 0 0R

I N 0 0 : 0 0 : 0 1 : 0 0O U T 0 0 : 0 0 : 0 3 : 0 0D U 0 0 : 0 0 : 0 2 : 0 0

C m te

R

oE d i E t r F u l lynt

R M A T T

p e do l

Display example for eachMEMORY key• When MEMORY key 1 is selectedR t P1 (or R, P2, BG)

• When MEMORY key 2 is selectedR t AUX

• When MEMORY key 3 is selectedR t MATT

2-2-9 GPI Output

320

BI

MAVE-F555 CONTROL

SUB MENU

GPI EP1 TIME(F)

GPI EP2 TIME(F)

Item number Display indication Settings Description

Sets control of MAVE-F555 when it is connected.

Performs offset control for the IN point of the GPI output. (GPI OUTPUTCONFIGURATION item (menu 224)).

-90 .. 00 .. +90

Notes: •When the player is an external VTR or when performing DMCediting, the PREROLL TIME + GPI EPx TIME must be set so that itexceeds 2 seconds plus 2 frames.

• When trimming, the GPI EPx TIME must be set so that it exceeds-28 frames (in 525 mode. -23 frames in 625 mode). In other editingsituations, PREROLL TIME + GPI EPx TIME must be set so that itexceeds 2 frames.

It is possible to use GPI (General Purpose Interface) output to control an external device, such as the audio signalfrom a CD player.Select “EP1” or “EP2” on the MAV-555 Expansion Menu item 224: GPI OUTPUT CONFIGURATION. Further,you must select “config” on the Expansion Menu item 225: GPI CONFIG MODE.



Chapter 2 O

peration

The MAVE-D555 allows mixing and swapping audiochannels in the interval where materials are presentedduring editing.

2-2-10 Audio Channel Mix/Swap Editing

Note

These features are available only when using theplayer port of the MAV-555.

You can perform GPI output with the menu above within ± 90 frames of the recorder IN point. It is not possible toperform GPI output for other intervals.

GPI output

IN OUT

Recorder

−90 frames +90 frames

−30 frames

Pre-roll time

REVSOFTBORDEDIT

LASTX

CLEAR

LOCMAN

PATTPRMTR

SOFIN

EOFOUT

STARTTOTAL

SPEEDDUR

T-TRACKF/TC

SCRGO TO

STBOFPLAY

STOPSHTL

EJECTSTILL

STEP-REW

STEP+FF

MENU+

SCR-C0

CTL/TC00

T-SET-

MARKSPEED


987

654

321

RETURNENTER


GHI JKL MNO _ / " @

ABC

, . : ; & # * ?

DEF ( ) [ ]

1 2 3 4

MEMORY


REDOUNDO

V A1 A2 A3 A4

TRIM

MARKSPLIT

EFFECT

R

STORE +-

P1 P2 BG

PORT/FILE ASSIGN

DELFILE

NEWFILE

FILE

MARK OUTMARK IN

REPLAYPREVIEW

EXECUTE/REC

SHIFT

MAV VTR


AMIX

4

MAVE-F555 MAVE-D555

1

6

8

5

2

34, 5 4, 5

2, 5

*When the GPI EP1 (or EP2) time is -30 frames


Chapter 2 O

peration

Setting Examples• These settings edit (swap) CH1 and CH3 on the

player port of the MAV-555.

Existing Value Setting Value1: MAV Player CH1 OUT 1 → 32: MAV Player CH2 OUT 2 → 23: MAV Player CH3 OUT 3 → 14: MAV Player CH4 OUT 4 → 4

• These settings edit (mix) CH1 and CH2 from theplayer port of the MAV-555.

Existing Value Setting Value1: MAV Player CH1 OUT 1 → 122: MAV Player CH2 OUT 2 → 123: MAV Player CH3 OUT 3 → 34: MAV Player CH4 OUT 4 → 4

Notes

• When mixing audio, the mixing method should beset from the MAV-555 Expansion menu item 820:AUDIO OUTPUT MIXING.

• Details of the Mix/Swap Edit can be confirmedfrom the information superimposed on the displaywhen the TYPE is set to full in the MAV-555Expansion menu item 323: LINEAR EDITMESSAGE.

0 1 : 0 0 A - F A D E R A A 0 0 : 0 4

P ] M I X + + 3 4V 1 2 3 4: 0 1 : 0 0

: 0 3 : 0 0*The “+” symbol signifies that the audio is mixed.

• When editing by using both the Mix/Swap Edit andthe Editing Fader Panel, each fader in the fader panelbecomes effective to the original channel set beforethe Mix/Swap Edit.

Category No. Name Remarks

2: Audio 1 MAV PlayerCH1 OUT

Specifies the recordingchannel(s) for the MAV-555player port audio outputchannel 1. 1

2 MAV PlayerCH2 OUT


3 MAV PlayerCH3 OUT


4 MAV PlayerCH4 OUT

Specifies the recordingchannel(s) for the MAV-555Player port audio outputchannel 4. 4

1 Press the A MIX key on the MAVE-F555 asindicated above so that it lights.The channels specified in the 2: Audio menu areoutput at the MAV-555 player port. When the AMIX key on the MAVE-F555 is not lit, mix/swapediting is not available.

2 On the MAVE-D555 press the MENU key (SHIFT+ [+]). The menu category display opens.

3 Press the “2 (AUDIO)” key on the keypad fromthe menu on the next page to select the category.The menu for the selected category opens.

4 Use the keypad keys on the MAVE-D555, or the“+” and “–” keys on the MAVE-F555 to select themenu number, then press the ENTER key.

5 Use the channel selection keys on the MAVE-F555 (A1 to A4 keys) and the “+” or “–” key tospecify the channels to output to each of theAUDIO CH1 to CH4 of the recorder at the MAV-555 player port. After specifying the channels,press the RETURN key (SHIFT key + ENTERkey) on the MAVE-D555 to exit menu.

6 Select the recorder port.

7 Select the interval (IN and OUT points) for editingspecified by the menu.

8 Press the EXECUTE/REC key on the MAVE-F555 to execute editing.

DisplayExample



Chapter 2 O

peration

2-2-11 Support of EDL Export

When the MAV-555 is used as a recorder during editing and used in parallel with the BZMA-E555 file transferprogram, it is possible to output EDL files (.edl) of editing results in the SONY BVE-9100 format. Also, when theVTR is used as a player during editing, it is possible to enter a tape’s reel name.

Notes

• The sequence in which entries appear in the exported EDL file does not match that in which editing operationsare performed using the MAVE-F555/D555. Since the MAVE-F555/D555 supports nonlinear editing (which wasnot possible with previous editors), the editing sequence cannot be output as is in the Sony BVE-9100 format.The EDL files exported using this function can be used with devices such as those of the BVE-series Editor onlyto replicate current editing results.

• This function can only export EDL files. Movement between pages in exported EDL files or data changes withthe MAVE-F555/D555 for the purpose of re-editing is not possible.

• Exporting EDL files is only possible when the MAV-555 is used as a recorder. When using the VTR as arecorder EDL files cannot be exported.

• When performing the following editing operations, the exportation of EDL files cannot be performed correctly.The sections edited as described below are exported as BLACK/MUTING.– When animation-type effects are used– When TITLE (DSK) are inserted

• When performing the following editing operations, the effect information is not output and transformed into cuts.– When performing DMC editing with effects– When performing manual effects– When adjusting the recording level of the edit interval together with the Editing Fader Panel BKNE-1011– When performing audio channel mix/swap editing


Chapter 2 O

peration

Setting a Reel Name

You can enter a tape’s reel name when using the BZMA-E555 to export EDL files and the VTR is used as a playerduring editing.

REVSOFTBORDEDIT

LASTX

CLEAR

LOCMAN

PATTPRMTR

SOFIN

EOFOUT

STARTTOTAL

SPEEDDUR

T-TRACKF/TC

SCRGO TO

STBOFPLAY

STOPSHTL

EJECTSTILL

STEP-REW

STEP+FF

MENU+

SCR-C0

CTL/TC00

T-SET-

MARKSPEED


987

654

321

RETURNENTER


GHI JKL MNO _ / " @

ABC

, . : ; & # * ?

DEF ( ) [ ]

1 2 3 4

MEMORY


REDOUNDO

V A1 A2 A3 A4

TRIM

MARKSPLIT

EFFECT

R

STORE +-

P1 P2 BG

PORT/FILE ASSIGN

DELFILE

NEWFILE

FILE

MARK OUTMARK IN

REPLAYPREVIEW

EXECUTE/REC

SHIFT

MAV VTR


AMIX

1 On the MAVE-D555 press the MENU key (SHIFT

+ [+]).

The menu categories are displayed.

2 Press the “4” key (REEL) on the keypad.

The unit enters the reel name setting mode andgoes on standby so you can enter a reel name.

3 Use the keys on the keypad to enter a new reelname.• Press the MARK SPEED key to switch between

the alphabetic and numeric entry modes on thekeypad.

• To move the cursor left or right, press the [?b] or[B?] key on the MAVE-F555.

• Press the CLEAR key to delete single characters.• Press SHIFT + CLEAR to delete an entire entry.

4 To register the new reel name, press the ENTER

key.

After setting a reel name, when you use theBZMA-E555 to export EDL files, the name isoutput.

5 To return to the category display, press theRETURN key (SHIFT + ENTER).

6 To quit menu operation, at the category displaypress the RETURN key (SHIFT + ENTER) again.

1

4

3

5, 63

2

MAVE-F555 MAVE-D555



Chapter 2 O

peration

Notes

• The length of a reel name is limited to 6 characters inlength.

• It is only necessary to set a reel name when using theVTR as a player during editing. When editing MAV-555 files, reel names are set automatically, and a reelname/file name correspondence list is inserted at thebeginning of the comment of exported EDL files.

• The EDL information is cleared if it not saved beforethe MAV-555 is turned off.


Chapter 2 O

peration

2-3 Using the Menus

This section describes the menus that are provided on the MAVE-D555 in order to set up operation settings.For more details about menu items, see the Menu List at the end of this manual.

2-3-1 Operations and Menus

The MAVE-D555 menu is divided into three categories: 1: Main, 2: Rename, and 3: Version. When you use amenu, first you select the category and then select the next menu from within the selected category.

Using the Menu Settings

You can perform the settings for each menu with the Main selection within the menu categories.

1 On the MAVE-D555 press the MENU key (SHIFT+ [+]).

The menu category display opens.

2 Press the “1” key on the keypad for “Main” toselect that category.

The menu for the selected category opens.

3 Enter the menu number using the numeric keys onthe MAVE-D555 or the [+] or [–] keys on theMAVE-F555, then press the ENTER key.

The menu data is displayed for the menu selectedby the number you entered.

4 To change a data setting, on the MAVE-F555 pressthe minus key [–] or plus key [+].

REVSOFTBORDEDIT

LASTX

CLEAR

LOCMAN

PATTPRMTR

SOFIN

EOFOUT

STARTTOTAL

SPEEDDUR

T-TRACKF/TC

SCRGO TO

STBOFPLAY

STOPSHTL

EJECTSTILL

STEP-REW

STEP+FF

MENU+

SCR-C0

CTL/TC00

T-SET-

MARKSPEED


987

654

321

RETURNENTER


GHI JKL MNO _ / " @

ABC

, . : ; & # * ?

DEF ( ) [ ]

1 2 3 4

MEMORY


REDOUNDO

V A1 A2 A3 A4

TRIM

MARKSPLIT

EFFECT

R

STORE +-

P1 P2 BG

PORT/FILE ASSIGN

DELFILE

NEWFILE

FILE

MARK OUTMARK IN

REPLAYPREVIEW

EXECUTE/REC

SHIFT

MAV VTR


AMIX

MAVE-F555 MAVE-D555

1

3, 4

2

5, 6, 7

3


Chapter 2 O

peration

5 To return to the menu name display, press theRETURN key (SHIFT + ENTER).

6 To return to the category display, press theRETURN key (SHIFT + ENTER) again.

7 To quit the menu operation, at the category displaypress the RETURN key (SHIFT + ENTER) again.

Confirming the Version Numbers for theMAVE-D555 and the MAVE-F555

Follow this procedure to confirm the current versionnumbers of the MAVE-D555 and the MAVE-F555.

1 On the MAVE-D555 press the MENU key (SHIFT+ [+]).


2 Press the “3” (Version) on the keypad.

The software version numbers of the MAVE-D555and the MAVE-555 are displayed in theinformation display area of the MAVE-D555.


4 To quit the menu operation, at the category displaypress the RETURN key (SHIFT + ENTER) keyagain.

LOCMAN

PATTPRMTR

SOFIN

EOFOUT

STARTTOTAL

SPEEDDUR

SCRGO TO

STBOFPLAY

STOPSHTL

EJECTSTILL

STEP-REW

STEP+FF


T-TRACKF/TC

MENU+

SCR-C0

CTL/TC00

T-SET-

987

654

321

RETURNENTER


GHI JKL MNO _ / " @

ABC

, . : ; & # * ?

DEF ( ) [ ]

1

23, 4


Chapter 2 O

peration

Renaming

File names cannot be renamed independently with the MAVE-F555. In order to rename files, the MAVE-D555must be connected to the MAVE-F555.

1 Using the MAVE-F555, select the port on which thefile whose name you want to change is loaded as thetarget port.

2 On the MAVE-D555 press the MENU key (SHIFT +[+]).


3 Press the “2” key (RENAME) on the keypad.

The unit enters the rename mode and standby status soyou can enter a file name.

4 Use the keys on the keypad to enter a new file name.• Press the MARK SPEED key to switch between the

alphabetic and numeric entry modes on the keypad.• To move the cursor left or right, press the [?b] or [B?]

key on the MAVE-F555.• Press the CLEAR key to delete single characters.• Press SHIFT + CLEAR to delete an entire entry.

5 To register the new file name, press the ENTERkey.


7 To quit menu operation, at the category displaypress the RETURN key (SHIFT + ENTER) again.

Note

The length of a file name is limited to 23 characters inlength.

REVSOFTBORDEDIT

LASTX

CLEAR

LOCMAN

PATTPRMTR

SOFIN

EOFOUT

STARTTOTAL

SPEEDDUR

T-TRACKF/TC

SCRGO TO

STBOFPLAY

STOPSHTL

EJECTSTILL

STEP-REW

STEP+FF

MENU+

SCR-C0

CTL/TC00

T-SET-

MARKSPEED


987

654

321

RETURNENTER


GHI JKL MNO _ / " @

ABC

, . : ; & # * ?

DEF ( ) [ ]

1 2 3 4

MEMORY


REDOUNDO

V A1 A2 A3 A4

TRIM

MARKSPLIT

EFFECT

R

STORE +-

P1 P2 BG

PORT/FILE ASSIGN

DELFILE

NEWFILE

FILE

MARK OUTMARK IN

REPLAYPREVIEW

EXECUTE/REC

SHIFT

MAV VTR


AMIX

MAVE-F555 MAVE-D555

4

6, 7

35

2

1

4

2-3 Using the Menus


Chapter 2 O

peration

2-4 Using the MAVE-D555 with the Editing Fader Panel

By connecting the Editing Fader Panel BKNE-1011 tothe MAVE-D555, you can control the recording levelduring editing and set effect parameters.

The functions of the controls of the Editing FaderPanel connected to the MAVE-D555 are describedbelow.

Track Fader and Master FaderControl the recording level during editing of the porttargeted for operation by selection with the MAVE-F555.

Volume Knobs (4)Set the effect parameters to match the display of theMAVE-D555 LCD.

Transition LeverOperate as a manual fader during manual transition.

Level MeterNot displayed (no used)

For details about effect parameters settings and manualtransition operations, see section “2-2-4 Setting EffectParameters” (page 2-9)

2-4-1 Adjusting the Recording Levelin Real Time at the Recording Interval

1 Before executing the edit, on the MAVE-F555press and light the AUDIO key of the EFFECToperation section.

2 During the PREVIEW, operate the fader and adjustthe recording level.

3 To execute the edit, press EXECUTE/REC as youwould normally.• While the AUDIO key is lit, the edit interval of

the PREVIEW is recorded. When the EXECUTE/REC key is pressed, the edit is executed for thetime used by the recorded material. However, ifyou want to change the level of the recordedrecording level, you can press SHIFT +EXECUTE/REC to once again record the editinterval.

• If you adjustment of the audio level is notrequired, press the AUDIO key to switch it offand the recording procedure described above willnot be executed.

• During edit execution the recording level isnormally adjusted via the R Port.

• When setting the recording level, when theAUDIO key of the MAVE-F555 is lit and aplayer port is selected, the fader is enabled.Therefore before performing a PREVIEW orEXECUTE/REC, the level can be confirmed.

• When the Editing Fader Panel is enabled (theAUDIO key is lit), information can besuperimposed on the monitor for confirmation.

C U T A - F A D E R

1

2

3

4

10

1

9

8

7

6

5

4

3

2

1

0

2 3 4 MKNOB

LEVER

INPUTMIX

1 23 4L R

10

9

8

7

6

5

4

3

2

1

0

10

9

8-10

-4-6-10-14

-20

-28

-40

-52-60-∞

7

6

5

4

3

2

1

0

Track Fader

Transition Lever

Level Meter

Master Fader

VolumeKnob

Appendixes A-1 (E)

Appendixes

Specifications

General

Power supply voltage 12 V DCPower consumption Max. 12 WOperating temperature +5°C to +40°C (41°F to 104°F)Storage temperature –20°C to +60°C (– 4°F to 140°F)Humidity 20% to 90%Mass 1.9 kg (1 lb 3 oz)External dimensions 148 × 102 × 307 mm (57/8 x 41/8 x 121/8 in.)

(width × height × depth, excluding projections)

Remote Connection

MOUSE/TRACK BALLMini DIN 6-pin receptacle × 1

AUDIO FADER PANELD-Sub 25-pin receptacle × 1

F555 I/F Mini DIN 8-pin receptacle × 1

Supplied Accessories

Operation Manual (this manual) × 1Installation Manual × 1MAVE-F555 connection cable × 1MAVE-F555 connection collar × 1MAVE-F555 fasteners (B3 × 6) × 4

Due to changes during product development, these specifications and the external appearance of the unit aresubject to change without prior notice.

A-2 (E) Appendixes

Appendixes

Menu List

The table below lists the menu options. Please note that the settings enclosed in are the default settings.

Category No. Name Content1: Main 1 DIAL DIRECT CONTROL When this item is on, without presssing the SHTL, JOG, or DMC key,

you can enter the dynamic motion control mode by turning the searchdial and control the playback speed. ONOFF

2 JOG DIAL MODE Selects whether to use the BVE-600 or BVE-9100 speed and anglesettings of the search dial when used in the DMC mode. BVE-600BVE-9100

3 JOG DIAL RESPONSE Sets the speed dial’s sensitivity to rotation when used in the jog mode(the amount of playback for one turn). HIGHLOW

4 BUZZER MODE Sets whether the buzzer sounds at the end of the edit session.ON OFF

5 STEP Sets the STEP increment.1field 2field4field10field1sec2sec3sec5sec

6 CONTROL PORT Determines how the control port is connected when the MONITOR portis changed. SeparatelySame as MonitorPort

7 V.O. VIDEO INPUT Specifies the input video signal when performing voice-over editing. SDIAnalogComposite

8 EDL AUTO SAVE Automatically saves cut point information of a saved file when it isedited. OFFMEMORY 1MEMORY 2MEMORY 3MEMORY 4

2: Audio 1 MAV Player CH1 OUT Specifies the recording channel(s) for the MAV-555 player port audiooutput channel 1. 1*CH1 to CH4 can be set independently.

2 MAV Player CH2 OUT Specifies the recording channel(s) for the MAV-555 player port audiooutput channel 2. 2*CH1 to CH4 can be set independently.

3 MAV Player CH3 OUT Specifies the recording channel(s) for the MAV-555 player port audiooutput channel 3. 3*CH1 to CH4 can be set independently.

Appendixes A-3 (E)

Appendixes

Category No. Name Content2: Audio 4 MAV Player CH4 OUT Specifies the recording channel(s) for the MAV-555 player port audio

output channel 4. 4*CH1 to CH4 can be set independently.

5 VOICE OVER MODE Specifies the mode when performing voice-over editing. NormalPre-Read

6 VOICE OVER INPUT Specifies the input audio signal when performing voice-over editing. SDIAES/EBUANALOG(You can select ANALOG when the BKMA-511 is installed in the MAV-555 or the BKMA-513 is installed in the MAV-555A.)

3: Rename – – Allows you to change the file name of a material.For more details about this operation, see “Renaming” (page 2-28).

4: Reel – – When exporting EDL files and using the VTR as a player, set a tape’sreel name.For more details about this operation, see “Setting a Reel Name” (page2-24).

5: Version – – Displays the current version number of the software:F555 Vx.xx (x.xx = current number)D555 Vx.xx (x.xx = current number)

Notes

• When 1: Main and 2: Audio category menu data is displayed, pressing the MAVE-D555 [CLEAR] key restoresthe settings of the selected menu to their default values. However, it is not possible to restore all the defaultsettings globally.

• During voice-over editing, the setting of menu 6: VOICE OVER INPUT in category 2: Audio takes precedenceover the MAV-555 R1 port audio input signal setting.

A-4 (E) Appendixes

Appendixes

Effect Parameter List

Category Name ContentDisplay Details

1: Patt Adj. – – Allows making effect pattern settings, such as the level of detail ofmosaics.

2: EDGE BORD Border Adjusts the width of borders.

0 to 100SOFT Softness Adjusts the softness.

0 to 100

CROP Crop Activates or deactivates the cropping function.

OFFAuto

Manual

* When using Auto, effect patterns are automatically adjusted.

L Left When CROP is set to Manual, sets the area to crop.R Right Left :-400 to 400

Top Top Right :-400 to 400

Btm Bottom Top :-300 to 300

Bottom :-300 to 3003: BDR MAT LUM Luminance Adjusts the border colors (luminance, saturation, and hue).

SAT Saturation Luminance :0 to 100

HUE Hue Saturation :0 to 100

Hue :359 to 0

4: INT V LUM Luminance Adjusts the optional BKMA-560 built-in Internal Video signal colors

SAT Saturation (luminance, saturation, and hue).HUE Hue Luminance :0 to 100

Saturation :0 to 100

Hue :359 to 0

TYPE Type Selects the optional BKMA-560 built-in Internal Video signal type.Matt

Color Bar

Grid

PTN Pattern Selects the pattern for Matt or Grid.1 to 52

5: Light Ctrl Control Activates or deactivates lighting.

OFF

ONTYPE Type Selects the lighting type.

Spot

Line

PlaneWID Width Selects the lighting width.

Wide

Medium

NarrowINTS Intensity Selects the lighting intensity.

High

Medium

Low

Appendixes A-5 (E)

Appendixes


6:Super BG BUS BUS Selects the Super BG BUS.

FG (Foreground)

BG (Background)

Internal VideoExternal

*Super BG switches from foreground to background during transitionsimilarly to a pattern 1900. For example, if Super BG is set to InternalVideo, the transition sequence is background --> Internal Video -->foreground.

7:DSK INV Invert Activates or deactivates DSK KEY signal turnover.

OFFON

FILL Fill Selects Fill signals.

V-IN :Use the external VTR Fill signal input at the left SPARE

terminal of the MAV-555 connector panel (with the MAV- 555SS in SD mode or the MAV-555A, the DSK IN VIDEO

terminal of the connector panel).

DSKM :Uses the built-in SG meant for DSK Fill as a Fill signal. Color

adjustment is performed from 8: DSK MAT.DNST Density Adjusts the DSK density.

0 to 100

8:DSK MAT LUM Luminance When FILL of item 7: DSK is set to DSKM, adjusts the DSK Matt

SAT Saturation colors.HUE Hue Luminance :0 to 100

Saturation : 0 to 100

Hue : 359 to 0

9:TITLE KEY KEY Selects the KEY signal type.LUM :Luminance key

CRK :Chroma key

SRC SOURCE Selects the KEY signal source. When KEY in item 9: KEY is set toCRK, you can only select SELF.K-IN :Use the external VIDEO signal input at the right SPARE

terminal of the MAV-555 connector panel (with the MAV-555SS in SD mode or the MAV-555A, the DSK IN KEYterminal of the connector panel).

SELF :Uses the signal from the MAV-555 internal player.

MASK MASK Activates or deactivates the KEY signal mask.

ONOFF

L Left Sets the masked area borders.

R Right Left :-400 to 400

Top Top Right :-400 to 400Btm Bottom Top :-300 to 300

Bottom :-300 to 300

INV Invert Activates or deactivates the masked area turnover.

ONOFF

A-6 (E) Appendixes

Appendixes


+:LUM Clip Clip Adjusts the Luminance key clip.

0 to 100

Gain Gain Adjusts the Luminance key gain.0 to 100

INV Invert Activates of deactivates the Luminance key turnover.

OFF

ONFILL Fill Selects the Fill signal when using the Luminance key.

VID :Player BUS

BDRM :Border MATT

DNST Density Adjusts the density of the inserted image when using the Luminancekey.

0 to 100

-: CRK Clip Clip Adjusts the Chroma key clip.

0 to 100Gain Gain Adjusts the Chroma key gain.

359 to 0

Hue Hue Adjusts the Chroma key hue.

359 to 0Ang Angle Adjusts the range of the Chorma key hue.

0 to 100

FILL Fill Selects the Fill signal when using the Chroma key.VID :Player BUS

BDRM :Border MATT

DNST Density Adjusts the density of the inserted image when using the Chroma key.

0 to 100

Effect Parameter List

Appendixes A-7 (E)

Appendixes

TITLE Key, Downstream Key, and Player BUS Setting Example

Player

Recorder

DSK Key

+: LUM-: CRKFILL

DSK MATT

[CUT]/[DISS]/[WIPE] key+

MEMORY key [1]/[2]/[3]

Key

DSK IN KEY

Fill

9: TITLE KEY

RP port

P2 port

BG port

VTR

EF MATT (INTV)

DSK IN VIDEO

7: DSK FILL

9: TITLESRC

SELF

K-IN

BDRM

VIDEO

LUM

DSKM

V-IN

DSK

TITLE

BDR MATT

CRK

[1]

[3] MATT

[2] AUX

* When EF editing, Player P2 only

(With MAV-555, right SPARE terminal)

(With MAV-555, left SPARE terminal)

DSK Fill

INPUT OUTPUT

* With CRK, can only select SELF

Printed on recycled paper

The material contained in this manual consists ofinformation that is the property of Sony Corporation and isintended solely for use by the purchasers of the equipmentdescribed in this manual.Sony Corporation expressly prohibits the duplication of anyportion of this manual or the use thereof for any purposeother than the operation or maintenance of the equipmentdescribed in this manual without the express writtenpermission of Sony Corporation.

Le matériel contenu dans ce manuel consiste eninformations qui sont la propriété de Sony Corporation etsont destinées exclusivement à l’usage des acquéreurs del’équipement décrit dans ce manuel.Sony Corporation interdit formellement la copie de quelquepartie que ce soit de ce manuel ou son emploi pour toutautre but que des opérations ou entretiens de l’équipementà moins d’une permission écrite de Sony Corporation.

Das in dieser Anleitung enthaltene Material besteht ausInformationen, die Eigentum der Sony Corporation sind,und ausschließlich zum Gebrauch durch den Käufer der indieser Anleitung beschriebenen Ausrüstung bestimmt sind.Die Sony Corporation untersagt ausdrücklich dieVervielfältigung jeglicher Teile dieser Anleitung oder denGebrauch derselben für irgendeinen anderen Zweck als dieBedienung oder Wartung der in dieser Anleitungbeschriebenen Ausrüstung ohne ausdrückliche schriftlicheErlaubnis der Sony Corporation.

Sony CorporationB & P Company

http://www.sony.net/

Printed in Japan

2002. 07.13

2001

MAVE-D555 (SY, 和,英)

3-205-546-02(1)

Documents

(for MAV-555 MULTI ACCESS VIDEO DISK RECORDER) MAVE …(for MAV-555 MULTI ACCESS VIDEO DISK RECORDER) MAVE-D555 (Ver. 1.30) ... 9100 format. Also, when the VTR is used as a player