Ged 2296

Stainless steel wire rod for drawing application

Grades Standard C Si Mn Ni Cr Mo Cu S P Co Al Ti Nb Rm max. Uses

UGI 4005SiUGIPERM® 12FM -

Min - 1.2 - - 11 - - 0.15 - - - - -510

Ferritic with improved magnetic properties for electroinjectorsMax 0.015 2 1 0.5 13 0.6 - 0.2 0.04 - - - -

UGI 4016UGI 430

EN 1.4016AISI 430SUS 430

Min - - - - 16 - - - - - - - -560 Controlled sulphur

grade 430Max 0.05 0.7 1 0.5 17 0.5 0.5 0.03 0.04 - - - -

UGI 4016LUGI 430L

EN 1.4016AISI 430SUS 430

Min - - - - 16 - - - - - - - -- Low carbon grade 430

Max 0.03 0.5 0.6 0.3 17 0.5 0.3 0.015 - - - - -

UGI 4104 EN 1.4104Min 0.1 - 1 - 15.5 0.2 - 0.25 - - - - -

600 Heat treatable gradeMax 0.15 0.7 1.5 0.5 17.5 0.5 - 0.35 0.04 - - - -

UGI 4105UGI 430F

EN 1.4105AISI 430FSUS 430F

Min 0.05 - 0.3 - 16 0.2 - 0.25 - - - - -560

Higher machinability but lower corrosion resis-tance than UGI 4016Max 0.08 0.7 0.8 0.5 17 0.5 - 0.35 0.04 - - - -

UGI 4106 1.4106XM34

Min - 1.25 - - 17.5 1.5 - 0.25 - - - - --

ferritic grade with improved magnetic properties for solenoid valve coresMax 0.03 1.6 0.7 0.5 18 2 - 0.3 0.04 - - - -

UGI 4113UGI 434

(1.4113)AISI 434

Min - - - - 16 0.8 - - - - - - -- -

Max 0.05 1 1 0.5 17 1.25 - 0.03 0.04 - - - -

UGI 4114UGI 182

EN 1.4114AISI XM 34

Min 0.05 - - - 17.5 1.5 - 0.15 - - - - --

Higher corrosion resistance than UGI 4104Max 0.08 1 0.5 0.5 18.5 2.5 - 0.25 0.04 - - - -

UGI 4511 EN 1.4511Min - - - - 16 - - - - - - - 12xC et 7(C+N)

470 Exhaust line hooks and partsMax 0.02 0.5 0.6 0.3 17 0.5 0.2 0.015 0.03 - - - 0,3

UGI 4601UGI 409CB

EN 1.4601ER 409Cb

Min - 0.3 0.3 0.2 11 - - - - - - - 10 x C- Exhaust line hooks

and partsMax 0.03 0.7 0.8 0.5 12 0.5 0.5 0.01 0.025 - - - 0,6

UGI 4742 EN 1.4742Min - 0.7 - - 17 - - - - - 0.7 - -

550 -Max 0.05 1.4 1 - 18 - - 0.015 0.04 - 1.2 - -

UGI 4763UGI 446 AISI 446

Min - - - - 23 - - - - - - - -600 Glass seal, steel wool

Max 0.06 0.7 1 0.5 24 0.5 0.5 0.03 0.03 - - - -

Ferritic

Grades Standard C Si Mn Ni Cr Mo Cu S P Co Ti N Nb Rm max. Uses

UGI 4362 EN 1.4362UNS S32304

Min - - - 3.5 22 0.1 0.1 - - - - 0.1 -- -

Max 0.03 1 2 5.5 23 0.6 0.6 0.01 0.035 - - 0.15 -

UGI 4460EN 1.4460AISI 329UNS S32900

Min - - - 4.5 25 1.3 - - - - - -- -

Max 0.05 1 2 6.5 28 2 - - 0.03 - - 0.2 -

UGI 4462UGI 45N

EN 1.4462UNS S31803

Min - - 1 5 22 2.5 - - - - - 0.14 --

High mechanical properties and excellent corrosion resistance. Off-shore applications (pins, bolts, etc.). Propeller shafts, petrochemical industry (PRE=33)Max 0.03 0.75 2 6 23 3.5 - 0.01 0.035 - - 0.2 -

UGI 4507UGI 52N+

EN 1.4507UNS S32550

Min - - - 6 24.5 3.3 1.2 - - - - 0.2 --

High mechanical properties and excellent corrosion resistance. Off-shore applications (pins, bolts, etc.). Propeller shafts, petrochemical industry (PRE=40)Max 0.03 0.7 1.5 7 26 4 2 0.01 0.035 - - 0.25 -

Duplex

Grades Standard C Si Mn Ni Cr Mo Cu S P Co Ti N Rm max. Uses

UGI 244CU -Min - - 3 3.5 16.2 - 1 - - - - 0.1

- -Max 0.07 0.5 4.5 4.5 17.5 0.5 2.5 0.015 0.04 - - 0.15

UGI 304HEN 1.4301AISI 304HSUS 304

Min 0.04 - - 8.5 18 - - 0.015 - - - -- Less hardenable grade than

UGI 4301-1Max 0.07 1 1.5 9.5 19 0.5 0.75 0.03 0.04 - - -

UGI 4301-1UGI 304-1

EN 1.4301AISI 304SUS 304

Min - - - 8 18 - - 0.015 - - - -- Min. Ni content

(AISI and EN standards)Max 0.07 1 1.5 9 19 0.5 0.75 0.03 0.04 - - -

UGI 4301-2UGI 304-2

EN 1.4301AISI 304SUS 304

Min - - - 8.5 18 - - 0.015 - - - -- Less hardenable grade than

UGI 4301-1Max 0.07 1 1.5 9.5 19 0.5 0.75 0.03 0.04 - - -

UGI 4301FGUGI 304FG

EN 1.4301AISI 304SUS 304FB

Min - - 1 9 18 - - 0.015 - - - -- Excellent forgeability

Max 0.05 1 2 10 19 0.5 0.75 0.03 0.04 - - -

UGI 4305UGI 303

EN 1.4305AISI 303SUS 303

Min - - 1.5 8.2 17 - - 0.25 - - - -- -

Max 0.07 0.75 2 9.2 18 0.5 0.75 0.35 0.04 - - -

UGI 4305HDUGI 303HD

N 1.4306AISI 304LSUS 304L

Min 0.04 - 1.5 8.5 17 - - 0.15 - - - -- Appropriate for severe

deformationsMax 0.07 0.75 2 9.5 18 0.5 0.75 0.25 0.04 - - -

UGI 4306EN 1.4306AISI 304LSUS 304L

Min - - 1 10 18 - - 0.015 - - - -- 304L high nickel content

Max 0.03 0.7 1.5 11 19 0.3 0.6 0.03 0.04 - - -

UGI 4307-1UGI 304L-1

EN 1.4307AISI 304LSUS 304L

Min - - - 8 18 - - 0.015 - - - -- Basic grade, low nickel content

Max 0.03 1 1.5 9 19 0.5 0.75 0.03 0.04 - - -

UGI 4307-2UGI 304L-2


Min - - - 9 18 - - 0.015 - - - -- Less hardenable grade than

UGI 4307-1Max 0.03 1 1.5 10 19 0.5 0.75 0.03 0.04 - - -

UGI 4307FGUGI 304LFG

EN 1.4307AISI 304LSUS 304LFB

Min - - - 9 18 - - 0.015 - - - -- Excellent forgeability

Max 0.03 1 1.5 10 19 0.5 0.75 0.03 0.04 - - -

UGI 4311 EN 1.4311AISI 304LN

Min - - - 8.5 18 - - - - - - 0.15- 304L with nitrogen content

Max 0.03 0.75 2 9 20 - - 0.03 0.045 - - 0.2

UGI 4401UGI 316

EN 1.4401AISI 316SUS 316

Min - - - 10 16.5 2 - 0.015 - - - -- Basic grade 316

Max 0.07 1 2 11 17.5 2.5 0.7 0.03 0.04 - - -

UGI 4401FGUGI 316FG

EN 1.4401AISI 316SUS 316 / 316FB

Min - - - 10.5 16.5 2 - 0.015 - - - -- Excellent forgeability

Max 0.06 1 2 11.5 17.5 2.5 0.7 0.03 0.04 - - -

UGI 4404UGI 316L

EN 1.4404AISI 316L

Min - - - 10 16.5 2 - 0.015 - - - -- Very good integranular corrosion

resistanceMax 0.03 1 2 11 17.5 2.5 0.7 0.03 0.04 - -

UGI 4404FGUGI 316LFG

EN 1.4404AISI 316L

Min - - - 11 16.5 2 - 0.015 - - - -- Better forgeability

Max 0.03 1 2 12 17.5 2.5 0.7 0.03 0.04 - - -

UGI 4406UGI 316LN

EN 1.4406AISI 316LN

Min - - - 10 16.5 2 - - - - - 0.12- 316L with nitrogen content

Max 0.03 0.75 2 11 18 2.5 - 0.01 0.04 - - 0.15

UGI 4435UGI 316LMo


Min - - - 12.5 17 2.5 - 0.01 - - - --

More Cr-Ni-Mo alloy than UGI 4404, increased corrosion resistance (pharmaceutical, medical, chemistry, etc.) Max 0.03 1 2 13.5 18 3 0.5 0.025 0.04 - - -

UGI 4436UGI 316Mo

EN 1.4436AISI 316SUS 316

Min - - - 11 16.5 2.5 - 0.01 - - - -- Very good integranular corrosion

resistanceMax 0.05 1 2 12 17.5 3 0.7 0.025 0.04 - - -

UGI 4539UGI 904L

EN 1.4539AISI 904L

Min - - - 24 19 4 1.2 - - - - -- Very high acid resistance

Max 0.02 0.7 2 25 20 5 2 0.01 0.03 - - 0.6

UGI 4541EN 1.4541SUS 321UNS S32100

Min - - - 9 17 - - 0.015 - - 5 X C --

Better corrosion resistance (particularly integranular)and better resistance to high T° than UGI 4307-2Max 0.06 1 2 10 18 0.5 0.5 0.03 0.04 - 0.6 -

UGI 4567UGI 304CU

EN 1.4567AISI 304CUSUS XM7

Min - - - 8.5 17 - 3 0.015 - - - --

Addition of copper, high cold deformability. Corrosion resistance similar to 4401.Max 0.03 0.7 1.5 9.5 18 0.5 3.5 0.03 0.04 - - -

UGI 4570UGI 303UX

EN 1.4570SUS 303Cu

Min 0.04 - 1.5 8 17 - 1.5 0.25 - - - -650 Better for drilling than

UGI 4305Max 0.08 0.75 2 9 18 0.5 1.8 0.35 0.04 - - -

UGI 4571 EN 1.4571SUS 316Ti

Min - - - 10.5 16.5 - - 0.015 - - 5 X C -- Very good corrosion resistance

(chemical industry)Max 0.03 1 2 11.5 17.5 2.5 0.5 0.03 0.04 - 0.6 -

UGI 4571FG EN 1.4571SUS 316Ti

Min - - - 11 16.5 2 - 0.015 - - 5 X C -610 Better forgeability than

UGI 4571Max 0.03 1 2 12 17.5 2.5 0.5 0.03 0.04 - 0.6 -

UGI 4597UGI 204CU

EN 1.4597UNS S20430

Min - - 7 1.25 16 - 2.5 - - - - -- Manganese and low nickel grade

Max 0.07 1 8 2.25 17.3 0.5 3.5 0.015 0.04 - - -

UGI 4828 EN 1.4828Min 0.13 1.5 - 11 19 - - - - - - -

- Heat resistantMax 0.17 2.5 2 12 20 - - 0.03 0.04 - - -

UGI 4841UGI 314

EN 1.4841AISI 314

Min - 2 - 19 24 - - - - - - -- High oxidation resistance

Max 0.08 2.5 2 21 26 - - 0.015 0.04 - - -

UGI 4845UGI 310

EN 1.4845AISI 310SUS 310

Min 0.05 - - 19 24 - - - - - - -- High oxidation resistance

Max 0.1 0.75 2 21 26 - - 0.015 0.04 - - -

Austenitic

Grades Standard C Si Mn Ni Cr Mo Cu S P Co Ti N Rm max. Uses

UGI 4000UGI 410L

EN 1.4000AISI 410SSUS 410

Min - - - - 12.5 - - - - - - - 560-

Max 0.03 0.5 1 0.6 13.5 0.5 0.5 0.015 0.03 - - - -

UGI 4005UGI 416

EN 1.4005AISI 416SUS 416

Min 0.09 - 0.7 - 12 - - 0.15 - - - - -Basic grade for the European market

Max 0.12 1 1.2 0.5 13 0.4 0.5 0.3 0.04 - - - -

UGI 4005AUGI 416A

EN 1.4005AISI 416SUS 416

Min 0.09 - 0.7 - 12 - - 0.25 - - - - - Better machinability than UGI 4005but lower corrosion resistance.Max 0.12 1 1.2 0.5 13 0.4 0.5 0.35 0.04 - - - -

UGI 4006UGI 410

EN 1.4006AISI 410SUS 410

Min 0.09 - - - 12 - - - - - - - -Basic grade

Max 0.12 0.7 1 0.5 13 0.5 0.5 0.03 0.03 - - - -

UGI 4006HUGIE 410H

EN 1.4006SUS 410

Min 0.12 - - - 13 - - 0.015 - - - - 560High carbon 4006 grade

Max 0.15 0.7 1 0.6 13.5 0.5 - 0.03 0.03 - - - -

UGI 4021UGI 420A

EN 1.4021AISI 420SUS 420J1

Min 0.18 - - - 12 - - 0.015 - - - - -Pump shafts, pistons, valves

Max 0.22 0.7 1 0.75 13 0.5 - 0.03 0.03 - - - -

UGI 4024 EN 1.4024SUS 410

Min 0.12 - - - 13 - - 0.015 - - - - 685High carbon 4006 grade

Max 0.15 0.7 1 0.6 13.5 0.5 - 0.03 0.03 - - - -

UGI 4028UGI 420B

EN 1.4028AISI 420SUS 420J2

Min 0.28 - - - 12 - - 0.015 - - - - - Higher mechanical properties than UGI 4021Max 0.32 0.7 1 0.75 13 0.5 - 0.03 0.03 - - - -

UGI 4029UGI 420F

EN 1.4029AISI 420FSUS 420F

Min 0.26 - 0.7 - 12 - - 0.15 - - - - - Higher mechanical properties than UGI 4005A.Max 0.31 1 1.3 0.5 13 0.4 - 0.25 0.04 - - - -

UGI 4031UGI 420C

EN 1.4031AISI 420

Min 0.36 - - - 12.5 - - 0.015 - - - - - Higher hardness but lower corrosion resistance than UGI 4028Max 0.42 0.7 1 0.75 13.5 0.5 - 0.03 0.03 - - - -

UGI 4034UGI 420D

EN 1.4034AISI 420

Min 0.43 - - - 12.5 - - 0.015 - - - - -Pins, needles, fuel-injection nozzles

Max 0.47 0.7 1 0.75 13.5 0.5 - 0.03 0.04 - - - -

UGI 4035EN 1.4035AISI 420FSUS 420F

Min 0.43 - 0.5 - 13 - - 0.18 - - - - -European grade (4034+S)

Max 0.48 1 1 0.5 14 0.2 - 0.26 0.04 - - - -

UGI 4057UGI 431

EN 1.4057AISI 431SUS 431

Min 0.17 - - 1.5 15.5 - - - - - - - - Excellent forgeability. Oil industry aeronautical industrySteel for moduls with good corrosion resistanceMax 0.2 0.8 1 2 16.5 0.5 - 0.03 0.035 - - - -

UGI 4057AUGI 431S

EN 1.4057AISI 431SUS 431

Min 0.14 - - 2 15 - - 0.015 - - - - 960 Better forgeability and machinability than UGI 4057Max 0.17 0.8 1 2.5 17 0.3 - 0.03 0.03 - - - -

UGI 4057FGUGI 431FG

EN 1.4057AISI 431SUS 431

Min 0.17 - - 2 15.5 - - - - - - - -Better forgeability than UGI 4057

Max 0.2 0.8 1 2.5 16.5 0.5 - 0.02 0.035 - - - -

UGI 4116N -Min 0.45 - - - 14.5 0.5 - - - - 0.1 0.08 - Substitution grade fpr 440C with

better corrosion resistanceMax 0.48 0.8 1 1 15 0.8 - 0.015 0.04 - 0.15 0.1 -

UGI 4122 EN 1.4122Min 0.35 - - - 15.5 0.9 - - - - - - -

-Max 0.43 0.8 1 1 16.5 1.2 - 0.02 0.03 - - - -

UGI 4313 EN 1.4313Min - - 0.5 3.5 12 0.5 - - - - - - - Excellent corrosion resistance in

aggressive environments, combined with high mechanical properties (recommended for cryogenics)Max 0.05 0.6 1 4 13 0.7 - 0.015 0.03 - - - -

UGI 4418UGI 165M EN 1.4418

Min - - 0.5 4 15 0.8 - 0.015 - - - - - Structural hardening steel. Very high mechanical properties and excellent corrosion resistance. Pump shafts, propeller shafts. Parts for the aeronautical industry.

Max 0.06 0.6 1 5 16 1.1 - 0.03 0.03 - - - -

UGI 4542UGI 630

EN 1.4542AISI 630UNS S17400SUS 630

Min - - - 4 15 - 3 0.01 - 5 X C - - --

Max 0.06 0.6 1 5 16.5 0.5 4 0.025 0.03 0.45 - - -

FLUGINOX 4922 EN 1.4922

Min 0.18 - - 0.4 11 0.8 - - - - 0.25 - 800-

Max 0.22 0.5 1 0.7 12 1.1 0.3 0.015 0.02 - 0.35 - -

FLUGINOX 4923 EN 1.4923

Min 0.18 - - 0.4 11 0.8 - - - - 0.25 - 800-

Max 0.22 0.5 1 0.7 12 1.1 0.3 0.015 0.02 - 0.35 - -

Martensitic

Ugitech SAFranceAvenue Paul GirodCS9010073403 UGINE Cedex www.ugitech.com

Non

con

tract

ual d

ocum

ent

Villi® - www.imprimerie-villiere.com

BrandLite – Wirerod_Etirage_EN/

03-2014–D2296EN

Documents

Ged 2296