Embed Size (px)
Citation preview
Global Water AP 1. Water Level Measurement Products
AP GLOBAL WATER WEBINAR SERIES 1 2020
Global Water Presenters
2
Jesse RandolphTechnical Support18 years with Global Water
Felipe ZambranoProduct Manager20 years with OI Corporation
3
4
Xylem Analytics/OI Corporation/Global Water Instruments
151 Graham Rd, College Station, TX 77842, United States
College Station Manufacturing Facility
5
WEB CATALOGwww.globalw.com
Webinar 1 Overview
6
Webinars1. Water Level
2. Water Flow &Samplers
3. Water Quality
4. Weather &Data Loggers
Water Level ProductsWL 400 – Submersible Pressure SensorWL16 – Submersible Pressure Sensor & LoggerWL450 – Submersible Pressure SensorDCX22 – Submersible Pressure Sensor (Absolute)WL705 – Ultrasonic Water Level (non-contact)WL900 - Radar Water Level (non-contact)WL500 – Tape Reel Water Level SounderWL650 – Sonic Water Level SounderWA600 – Water Level Alarm Products
7
SUBMERSIBLE PRESSURE SENSORS
Pressure Sensor – Measurement Technology
8
Water Pressure SensorsPhysical diaphragm, which bends as pressure is applied. This resistance is used to modify the output voltage of the sensor.
Relative Pressure SensorAKA Vented, Gauge
Absolute Pressure Sensor
Vented Cable
Submersible Pressure Sensors – Background Information
9
ABSOLUTE PRESSURE SENSORS
• No cable required, ideal for very long cable run requirements
• Compensation for barometric pressure required from additional sensor (Baro Sensor)
• Errors associated with deriving stage compounding accuracies from two sensors
RELATIVE (VENTED) PRESSURE SENSOR
• No compensation for barometric pressure required, not reliant on additional centre
• More accurate, in particular in low pressure (stage) applications
• Water ingress via vented sensor will destroy sensor.
• Global Water Wet-wet water level sensor eliminates vent tube concerns.
10
WL400
Applications
11
Water level, well depth, groundwater level, surface water flow, pipe flow, and water pressure, etc...
NOTE: Polyurethane cable is not recommended for use with hydrocarbons or high concentrations of chlorine. Please look at the our WL450 Water Level Transmitter to meet the requirements of these types of applications.
WL400 – Relative Water Level Sensor
12
KEY SPECIFICATIONS
Analogue Output: 4-20mA Accuracy: ±0.1% constant temp, ±0.2% over (1.37° to 21.1°C) rangeDynamic temperature compensation systemPressure Range: 0-3ft (0.91m), 0-15ft (4.57m), 0-30ft(9.14m), 0-60ft (187.29m), 0-120ft (36.58m), 0-250ft(60.96m), 0-500ft (152.4m)Diameter: 21mmCable Length: 4-20 mA signal can run up to 914m Maximum Cable Length 305mCE CertifiedWL-T Temperature Output Option
Vented Level Sensor – Desiccant Pack and Long Cable Runs
13
Maximum Cable Length 305m
Maximum Cable Length 914m
Sensor to End Cable
3 Core WireDesiccant Pack
WL400 OPTIONS & ACCESSORIES
14
WL-SWO Sewer Flow Option (PN# AG0000)
EZ100 LCD Sensor Display
15
WL16/FL16
Applications
16
Groundwater monitoring, stream and river gauging, lake/pond level analysis, flood level recording, irrigation canals, inflow and infiltration studies, wetland/estuary monitoring, weirs and flumes, wave and tidal analysis, and MUCH MORE...
WL16 – WL400 + Integrated Data Logger
17
KEY SPECIFICATIONSBattery Type: 2 X 9VDC Alkaline (approximately 1 year continuous operation)
Memory: Up to 81,000 Readings
Software & USB Cable INCLUDED
Compatibility: All versions Windows including 10
Four sample modes: 10 times per second, interval, logarithmic, and exception
User programmable start and stop alarms, engineering units, and field calibration setup
SOFTWARE
18
4 STEP CALIBRATION
PROCESS
FL16 – WL16 with Flow Calculation
19
Mannings, Pipe Flow, Weirs and Flumes
20
WL430
Applications
21
Ideal for severe high solids environments such as sewage, lift stations, storm canals, wet wells, slurry tanks, and more.
Handles hydrocarbons and high concentrations of chlorine.
WL430 SEWAGE LIFT STATION WASTEWATER LEVEL SENSOR
22
Output: 4-20 mA
Accuracy: ±0.5% of range
Ranges: 7m & 10m
Cable: 12m Standard
”Steelcage” design gives full protection and allows sensing to sewage levels no matter how much debris/mud/sand or rags build up.
WL430 Typical Installation
23
24
WL450
Applications
25
Ideal for environmental monitoring applications such as test wells, surface water, rivers, lakes, runoff, drainage basins, irrigation canals, and more.
WL450 ALL STAINLESS STEEL WATER LEVEL TRANSMITTERS
26
KEY SPECIFICATIONS
Analogue Output: 4-20mA
Accuracy: ±0.1%
Pressure Range: 0-3ft (0.91m), 0-15ft (4.57m), 0-30ft(9.14m), 0-60ft (187.29m), 0-120ft (36.58m), 0-250ft(60.96m), 0-500ft (152.4m)
Diameter: 21mm
Cable Length: 3000ft *BR100 Boost Regulator required (24V Supply) if cable is over 50 feet
CE Certified
27
DCX-22
Applications
28
Monitoring sites with high vandalism opportunity, groundwater monitoring, stream and river gauging, irrigation canals, inflow and infiltration studies, wetland/estuary monitoring, Weirs and Flumes, and MUCH MORE...
Self-contained water level dataloggers work well for many users because the depth of deployment is not dependent on the length of the cable.
For example, if you need to drop the water level datalogger over the side of a bridge, or off a high dock, or down a deep well hole where the static water level is many feet below surface, the water level datalogger's 15' sensor range is great but you might have to have 200 feet of cable to get to the water level measurement point.
DCX-22 SELF CONTAINED WATER LEVEL DATALOGGERS
29
KEY SPECIFICATIONS
Battery Life: 10 years @ 1 measurement/hour
Level Accuracy: ±0.1%
Baro Accuracy: 1 mbar
Memory: 16,000 or 28,000 data points
Diameter: 22mm
CE Certified
NON-CONTACT WATER LEVEL MEASUREMENT
30
31
WL705
Applications
32
The unique 3ft range ultrasonic water level sensor is ideal for measuring flow in small flumes and weirs.
The 12ft and 48ft ultrasonic water level sensor ranges are best for measuring river, lake and tank levels and for measuring open channel flow in larger flumes.
WL705 ULTRASONIC WATER LEVEL SENSOR
33
KEY SPECIFICATIONS
Output: 4-20 mA
Ranges: 0.33 to 3ft (0.1-0.91m); 0.33 to 12ft (3.66m); and 1 to 48ft (14.63)
Accuracy: Better than 0.5% of range
Cable Length: Up to 500ft
Dimensions: (103.2 L x 26.7 Dia mm), (121 L x 60 Dia mm)
CE Certified
34
WL900
Applications
35
Ideal where application conditions are in need of non-contact liquid level measurement, but ultrasonic level transmitter measurement is not acceptable.
For example, reflective liquids that have a foaming surface, vapors, or dusty conditions beyond ultrasonic transmitter capabilities.
WL900 RADAR LEVEL TRANSMITTERS
36
KEY SPECIFICATIONS
Output: 4-20 mA
Ranges: 10 inch to 50 ft (0.254 to 15.2 m)Accuracy: ±0.25% of range
Cable Length: Up to 500ft
Dimensions: (10cm dia. x 45.7cm long)
Push-button calibration system
CE Certified
37
WL500
Applications
38
The WL500 Well Level Sounder is a portable instrument used to accurately measure water levels in monitoring wells and bore holes.
When the water level sounder's probe assembly makes contact with the surface of the water, a bright LED glows and a beeper sounds on the reel.
WL500 WATER LEVEL SOUNDER
39
• Audio alert beeper and LED indicate contact with the water.
• Ranges: 15m, 30m, 50m, 60m, 100m, 120m, 150m, up to 925 m
5/8" (1.59cm) Field Replaceable Sensor Optional 3/8" (1cm) Sensor (non-field replaceable)
40
WL550
Applications
41
WL550 Oil Water Interface Meter can be used in numerous applications including measuring oil and water levels in monitoring wells, detecting tank leakage and obtaining accurate measurements of water levels.
The oil water interface probes use infra-red refraction to detect hydrocarbons and conductivity to detect water.
When the WL550 Oil Water Interface Meter is lowered down a well and contacts the product layer, a solid tone and green light alarm is activated on the reel. When the probe detects water, the tone begins to oscillate and the light changes to red.
WL550 OIL WATER INTERFACE METERS
42
• Audio alert beeper and LED indicate contact with the water.
• Ranges: 15m, 30m, 50m, 60m, 100m, 120m, 150m, up to 925m.
• WL550 Oil Water Interface Meter tapes are chemically resistant to all chemicals found in environmental monitoring.
Rugged Aluminum Bearing
5/8" (1.59cm) Field Replaceable Sensor Only
43
WL650
Applications
44
The WL650 Sonic Water Level Meter allows to measure crooked wells, wells with cascading water, partially cased rock wells, wells with submersible pumps, capped or uncapped wells, wells with pipes and wires inside.
As long as the obstructions take up no more than half of the bore area the meter will not suffer any loss of accuracy. The sonic water level meter should only be used on wells under 10 inches in diameter as the accuracy decreases with larger diameter wells.
WL650 SONIC WATER LEVEL METER
45
• Audio alert beeper and LED indicate contact with the water.
• Measurement range: Normal (3-152 m), Deep (61-366 m)
• Resolution: 30mm
• Measurement accuracy: +/- 0.2% of reading
46
High Water Alarm Systems
Applications
47
The WA400 Water Level Alarm is a reliable high or low water level alarm with a weather resistant PVC enclosure for outdoor applications. Includes a bright flashing strobe light and loud sounder for alarm notification
WA400 – High Water Alarm
48
• On alarm triggers strobe light and sounder
• DC or AC powered versions
• Integrates easily with GWI switches
WA150 Tilt Float Switch
WA600Water Level Alarm Sensor
WA100 Liquid Level Float Switch
WA400 Water Level Alarm
49
Webinars1. Water Level
2. Water Flow & Samplers
3. Water Quality
4. Weather & Data Loggers
Reminder - Webinar 4Data logger and telemetry options for water level
sensors
Reminder - Webinar 2Water Flow & Samplers
May 2020
Questions?Justin Stockley
Xylem AP Surface Water Manager
OR
Felipe Zambrano
Global Water Product Manager
OR
Jesse Randolph
Global Water Technical Support
Contact us:
