頁 １／２

類別 ＴＭＢ４技 術 資 料

作 成 部 門

番号 Ｔ６１７－０9 流通交通機器事業部 設計部

取 扱 要 領 資 料承 認 検 印 担 当

佐藤

型 式 GFB－800型

製品名 小型紙幣計算機

資料名 取扱説明書

ＧＬＯＲＹ0901 000048:2001-07-01

頁 ２／２

改 正 履 歴

版 数 年 月 日 主 な 内 容 担 当

初版 2001- 8- 9 宝達

０１ 2001- 9-21P8最下部文章修正

佐藤

０２ 2001-10-19シリ－ズ機追加により全面改訂

佐藤

０３ 2002- 2-14GFB941追加により改訂

矢野

０４ 2002- 5-31GFB830A仕様変更に伴い変更

矢野

０５ 2002-6-24・GFB836仕様変更に伴い変更(P14、P17）・誤記訂正(P23)accesory削除 矢野

０６ 2003-01-10GFB841追加により変更(P13、P17）

佐藤

０７ 2003-07-07CEマーキング規格改正による適合宣言書の変更

矢野

０８ 2005-10-26CEマーキング規格改正による適合宣言書の変更

矢野

０９ 2006-06-05CEマーキング規格改正による適合宣言書の変更

矢野

１０ - -

１１ - -

１２ - -

１３ - -

１４ - -

１５ - -

１６ - -

１７ - -

類別 ＴＭＢ４ 番号 T617-09ＧＬＯＲＹ0901 000048:2001-07-01

GFB-800・900 series

OPERATING INSTRUCTIONSGLORYBANK NOTE COUNTING MACHINE

FOREWORDCongratulations on your selection of a GLORY Bank NoteCounting Machine. This manual has been compiled to providecomplete instructions for operating the machine.Before starting, please read the instructions thoroughly tofamiliarize yourself with all of its functions and operations of themachine and keep this manual nearby for quick reference.

The GFB-800･900 series are designed for counting bank notes.Unauthorized modification of the GFB-800･900 series withoutGLORY's permission will result in the invalidation of allguarantees.

The information contained in this manual is subject to changewithout notes.The contents of this manual may not be reproduced in any formwithout the explicit permission of GLORY.

Notes in Using Machine

⇒　To make the most use of this machine

→Avoid operation under direct sunlight.

→Don't press the operation-keys with a pointedtip of pencil or anything pointed.

→Don't make multi wiring from one socket.

⇒　To make this machine with safety

→Three-pole plug which can be grounded to thebuilding ground should be used for power supply.

＊Use the power cable attached to the machine asaccessories.

→Unplug the machine before it is moved.

→Don't place tools, fingers, hair, loose clothing, etc.near any moving part.

→Don't open the Hopper during machine operation.When the Hopper is to be opened, make sure thatthe machine is first turned off.

→Don't spill drink etc. on the machine.

→For maintenance, use specified parts;don't make improper maintenance.

WARNING:This equipment has been tested and found to comply with the limits for a Class Adigital device, pursuant to part 15 of the FCC Rules. These limits are designed toprovide reasonable protection against harmful interference when the equipment isoperated in a commercial environment. This equipment generates, uses, and canradiate radio frequency energy and, if not installed and used in accordance with theinstruction manual, may cause harmful interference to radio communication.Operation of this equipment in a residential area is likely to cause harmful interferencein which case the user will be required to correct the interference at his own expense.

★　Specification subject to change without notice.★　We shall be free from any balance for the injury or right of a third paty

caused by using the date contained herein.★　Reproduction for the purpose of profit-making without permission shall be

forbidden.

WARNING:This is Class A product. In a domestic environment this product may cause radiointerface in which case the user may be required to take adequate measure.

If your line voltage is 220 to 240V, use one of the following types of cable. (For 220V to 240V)

PlugConfiguration Plug Type Line Voltage

Selector SettingReferenceStandards Power Cord

EURO240V10-15A

200-240V CEE(7),ⅡⅣⅦIEC 83IEC 127

Type SVT or＜HAR＞No. 18/3AWG300V, 10A

UK240V6A

200-240V BS 1363IEC 83IEC 127

Type SVT or＜HAR＞No. 18/3AWG300V, 10A

Australian240V10A

200-240V AS C112IEC 127 Type SVT or＜HAR＞

No. 18/3AWG300V, 10A

NorthAmerican240V15A

200-240V ANSI C73-20NEMA 6-45-PIEC 83UL 198.6

UL ListedType SVTNo. 18/3AWG300V, 10A

Switzerland240V6A

200-240V SEVIEC 127

Type SVT or＜HAR＞No. 18/3AWG300V, 10A

If your line voltage is 100 to 120V, use one of the following types of cable. (For 100V to 120V)

PlugConfiguration Plug Type Line Voltage

Selector SettingReferenceStandards Power Cord

NorthAmerican125V10A

100-120V ANSI C73.11NEMA 5-15-PIEC 83

UL ListedType SVT or SJTNo. 18 or 16/3AWG or＜HAR＞300V, 10A or 13A

CONTENTS

NAME AND BRIEF DESCRIPTION OFMAIN PARTS

Appearance ………………………1Operation panel and display ………………3

HOW TO OPERATE MACHINE

Counting Bank Notes …………5Different denomination detection function ………9Counterfeit note detection function ………11

TROUBLE SHOOTING

PRECAUTIONS FOR HANDLINGOF MACHINE

DAILY CLEANING OF THEMACHINE

SPECIFICATIONS

ACCESSORIES

　　　　　　　　　　　　　　24

　　　　　　　　　　　　　　23

　　　　　　　　　　　　　　 18

　　　　　　　　　　　　　　24

　　　　　　　　　　　　　　22

2

3

4

7

6

51

NAME AND BRIEF DESCRIPTION OF MAIN PARTSAppearance

1

1

②

③

④

⑤⑥

①

⑦

Appearance

2

①　HOPPER　　Notes to be counted are placed in the Hopper.

②　AUXILIARY HOPPER PLATES　　Guide plates for leading the notes into the

feeding mechanism.

③　HANDLE　　Used for carrying the machine.

④　PAPER THICKNESS ADJUSTMENT SCREWUsed to make the machine count notessmoothly regardless of paper thickness thatmay vary with denominations.(Gate adjustment of this machine has beenmade at the factory.)

⑤　STACKER　　Counted notes are stacked in the Stacker.

⑥　POWER SWITCH　　Main power on/off switch.

⑦ CONNECTING PORT FOR I/F CONNECTOR (option)Used to connect a Communication Line.(connected with an optional RS-232C,Customer Display.)

Operation panel and display

3

⑨ ⑧⑩

⑪

⑫⑬

⑭⑮⑯

⑰

⑱

Operation panel and display

4

⑧　RESTART KEY　　Used to start counting operation in the following

cases.a. To resume counting after an error is cleared.b. To clear the displayed counted number.c. To start counting when the AUTO/MNL key is

set to MNL.

⑨　TEN-KEY PAD　　This is set of numerical keys (0-9); used to input

optional batch sizes.

⑩　BATCH KEY　　Everytime this key is pressed, one of the preset　　batch amounts “10”, “20”, “25”, “50”, “100” and“(infinity)” will be displayed and selected byrotation on the Batch Number Display.

⑪　CLEAR KEY　　Pressing this key clears the displayed Batch Size.

⑫　COUNTING NUMBER DISPLAY　　The number of counted notes is displayed here.

⑬　BATCH NUMBER DISPLAY　The optioned number of notes to be batched is

displayed here.

⑭　DOUBLE NOTE DETECTION LEVEL KEY　This key changes the threshold for double note

detection according to the degree of stain/printingdarkness of notes to be counted.

⑮　ADD KEY　By this key, the machine is set so that each counted

number of notes in a bundle successively set in theHopper can be added up. (add function)

⑯　DD KEY　By pressing this key, the size of the first counted

note is memorized and in case a smaller or largersize note is detected, the machine will stop.

⑰　COUNTING SPEED CHANGE KEY　Counting speed is selected from the four rates.　(1800, 1500, 1000, 500 notes/min.)

⑱　AUTO/MANUAL KEY　Start of counting operation can be set either to Auto

start or to Manual start.

・ CF KEY(except for GFB800/900)By pressing this key, the machine will stop in case acounterfeit note is detected. (CF stop function)

HOW TO OPERATE MACHINECounting Bank Notes

5

1.　Switch on the machine.

＊“0” will be displayed on the Counted Number Display and“100” will be displayed on the Batch Display.

2.　Check the double note detection level and set it if necessary.

＊ By pressing the Double Note Detection Level Key, set aproper threshold for double note detection according to thedegree of stain/printing darkness of notes to be counted.

＊ Every press of this key will change the position of the Level-lamp.

For notes which are stained or printed dark, set the Level-lamp to the position “ 　　”. For notes which are newor printed light, set the lamp to the position “ 　　 ”.

＊ When the lamp of the machine is set to the AUTO position, aproper threshold is set automatically.

Note:When dirty notes are mixed, do not use the AUTO position asthere is a possibility that the detection function does not workcorrectly.Please set notes at the center of the Hopper. If they arelaterally shifted to the right or left greatly, there is a possibilitythat correct detection cannot be assured.

2

Counting Bank Notes

6

3.　Check the Addition Lamp and activate the ADD function.

＊　To add counted numbers one after another, press theADD Key to activate the ADD function making theaddition Lamp lit.

4.　Set the optional batch number.

＊　Set the batch number by pressing the BATCH Key.Every time this key is pressed, one of the preset values“10”, “20”, “25”, “50”, “100” or “(infinity)” will be displayedby rotation on the Batch Number Display. Countingoperation will stop when the counting number reachesthe set batch number.

＊　In case a“infinity”is selected on the Batch NumberDisplay, the machine will count up all notes placed in theHopper without interruption.

＊　Any optional batch number (1－999) other than thepreset values can be set by pressing the Ten Keys Pad.

Counting Bank Notes

7

5.　Set the Counting speed.

＊ Set the Counting speed by pressing the SPEED Key. Everytime this key is pressed, one of the preset rates “500”,“1000”, “1500” or “1800” notes/min will be displayed byrotation on the Counting Number Display.

Counting Bank Notes

8

6.　Set a bundle of bank notes to be counted in theHopper.

＊　For the method to set notes, refer to Chapter 4“Precautions for handling of machine/How to setbank notes” (page 22).

＊　Set notes to be counted in the Hopper and themachine will start counting automatically.

＊　If a batch number has been set, the machine willstop when the batch number is reached. After thebatched notes are removed from the Stacker, thenext counting operation will start automatically.

⇒　For reference

■ How to change batch number for each batch countingThe procedure stated left is for the case when theAUTO Lamp is lit.In case the AUTO lamp is not lit, press the RESTARTKEY each time to start counting. This method issuitable when batch number is changed for eachbatch counting.

■What is the “ADD function”When counting operation for a bundle of notesplaced in the Hopper is finished, the countingoperation for the next bundle of notes will bestarted from “0” on the Counting Number Display.When counting operation is started in the ADDfunction, the counted numbers for succeedingbundles of notes will be added and displayed.

Different Denomination Detection Function

9

⇒　Through this function the size of the first counted note is memorized and if a note whose size is different from thememorized value is detected, the machine will stop. (While the GFB800 series machines detect size differencewidthwise, the GFB900 series detect size difference both widthwise and lengthwise.)

Setting of DD detection function

1.　Press the DD key to set to the “DD detection function”☆DD Lamp will be lit.

NOTE:Difference between note sizes of different denominations isdetected by checking the width of each note to be counted.The machine is set up so that it can detect notes of differentdenomination when the size difference is 5mm or more.

2.　When the machine stops after detecting a differentdenomination note, remove the detected notefrom the Stacker and press the RESTART KEY toresume counting.

Clearing memory of a denomination

■In case the Addition Lamp is not lit !Remove the notes from the Stacker. The memorizedvalue will be cleared when the number on theCounting Number Display becomes “0”.

　　

■In case the Addition Lamp is lit !Remove the notes from the Hopper and Stacker,and press the RESTART KEY; memory will becleared with the indication on the CountingNumber Display at“0”.

Different Denomination Detection Function

10

NOTE:

①Notes of other denominations are detected by difference in size between various denominations bychecking the width of each note to be counted. The machine is set at the time of shipment from factoryso that it can detect the size difference 5 mm or more.This limit of 5 mm can be reduced to 3 mm, if necessary, by contacting a Glory representative for thismodification.

②One/two is subtracted from the counted number when “dd” / “dd2” is displayed on the Batch NumberDisplay respectively. It is also possible to set a mode to subtract nothing from the displayed number.

③If this function is activated while the counting speed 1800 notes/min is selected, the counting speed willbe automatically changed to 1500 notes/min.

Counterfeit note detection function

11

⇒　This function makes the machine stop when it detects a suspicious note.

Activating the CF (counterfeit note) detection function

1.　Press the CF key to activate the counterfeit note detection function.Then “CF SET” is displayed on the display.

Pressing the detection method selection key on the ten-key pad while“CF SET” is displayed makes the corresponding detection methodeffective and the corresponding LED light up.

2.　When the machine stops through this function, remove the detectednote from the Stacker and recount all the other notes in the Stacker.

3．Deactivating the functionPressing the detection method selection key on the ten-key pad againwhile “CF SET” is displayed makes the corresponding detectionmethod ineffective and the corresponding LED go out.Pressing the CF key again while “CF SET” is displayed makes all thedetection methods ineffective.

NOTECheck the removed suspected note. If it is found to be a genuine note, return it to the stacker and pressthe REATART KEY to continue counting.

Counterfeit note detection function

12

Notes: The following are applicable to all the counterfeit note detection function modes (AUTO, US and EU) in thesubsequent pages.

①If the counterfeit note detection function at the speed 1500 notes/min or 500 notes/min is notsatisfactory, count notes at the speed 1000 notes/min.

②If the counterfeit note detection function is activated while the counting speed 1800 notes/min isselected, the counting speed will be automatically changed to 1500 notes/min.

Counterfeit note detection function (CF AUTO MODE)

13

⇒　This function automatically sets the detection method by investigating thecharacteristics of the first counted note. The subsequent notes from thesecond note will be checked by this detection method.When notes to be counted have different characteristics, it is not necessaryto change the setting.(Applicable only to GFB-830, 832, 841,850, 932, 937, 941, 946, 955 and 956)Activating the CF AUTO detection mode1.　Press the CF key to activate the counterfeit note detection function.

Then “CF SET” is displayed on the display.Pressing the AUTO key while “CF SET” is displayed activates thecounterfeit note detection AUTO mode and the corresponding LED willblink.Once the first note is counted and its characteristics are known, the LEDshowing the detection method will light up.

2.　When the machine stops after detecting a suspicious note, remove thedetected note from the Stacker and recount all the other notes in theStacker.

3. Deactivating the functionPressing the detection method selection key on the ten-key pad againwhile “CF SET” is displayed makes the corresponding detectionmethod ineffective.Pressing the CF key again while “CF SET” is displayed makes all thedetection methods ineffective.

NOTECheck the removed suspected note. If it is found to be a genuine note, returnit to the stacker and press the REATART KEY to continue counting.

14

Counterfeit note detection function (CF US 100 MODE)

⇒　This function makes the machine stop when it detects a suspicious US $100 note.(Applicable only to GFB-830, 832, 836 and 850)

Activating the CF US $100 detection mode

1.　Press the CF key to activate the counterfeit note detection function.Then “CF SET” is displayed on the display.

Pressing the “1” key on the ten-key pad while “CF SET” is displayedmakes “US SET” appear on the counted number display and the CFLED automatically light up. (A dot will appear at the lower left corneron the batch number display.)

2.　When the machine stops after detecting a suspicious note, remove thedetected note from the Stacker and recount all the other notes in theStacker.

3. Deactivating the modePressing the “1” key on the ten-key pad again while “CF SET” is displayedmakes the mode ineffective.Pressing the CF key again while “CF SET” is displayed makes all thedetection methods ineffective.

NOTEIf this mode is used for counting notes other than the US $100 notes,erroneous detection may occur. Please use this mode only for the US$100 notes.

15

Counterfeit note detection function (CF US 100 MODE)

⇒　This function makes the machine stop when it detects a suspicious US $100 note.(Applicable only to GFB-830A)

1. Activating the CF US $100 detection mode

Press the CF+ key to activate the counterfeit note detection function.Then “US SET” is displayed on the display and the CF LEDautomatically light up. (A dot will appear at the lower left corner on thebatch number display.)

2.　When the machine stops after detecting a suspicious note, remove thedetected note from the Stacker and recount all the other notes in theStacker.

3. Deactivating the modePressing the “CF+” key again makes the mode ineffective.

NOTEIf this mode is used for counting notes other than the US $100 notes,erroneous detection may occur. Please use this mode only for the US$100 notes.

Counterfeit note detection function (CF US MODE)

16

⇒　This function makes the machine stop when it detects a suspicious USdollar note.(Applicable only to GFB-932, 937, 955 and 956)

Activating the CF US notes detection mode

1.　Press the CF key to activate the counterfeit note detection function.Then “CF SET” is displayed on the display.

Pressing the “1” key on the ten-key pad while “CF SET” is displayedmakes “US SET” appear on the counted number display and the CFLED automatically light up. (A dot will appear at the lower left corner onthe batch number display.)

2. When the machine stops after detecting a suspicious note, remove thedetected note from the Stacker and recount all the other notes in theStacker.

3. Deactivating the modePressing the “1” key on the ten-key pad again while “CF SET” is displayedmakes the mode ineffective.Pressing the CF key again while “CF SET” is displayed makes all thedetection methods ineffective.

NOTEIf this mode is used for counting notes other than the US dollar notes,erroneous detection may occur. Please use this mode only for the USdollar notes.

Counterfeit note detection function (CF EU MODE)

17

⇒　This function makes the machine stop when it detects a suspicious Euro note.(Applicable only to GFB-832, 836, 841,932, 937, 941, 946, 955 and 956)

Activating the CF Euro notes detection mode

1.　 Press the CF key to activate the counterfeit note detection function.Then “CF SET” is displayed on the display.Pressing the “2” key on the ten-key pad while “CF SET” is displayedmakes “EU SET” appear on the counted number display and the CFLED automatically light up. (A dot will appear at the lower left corner onthe batch number display.)

2.　 When the machine stops after detecting a suspicious note, remove thedetected note from the Stacker and recount all the other notes in theStacker.

3. Deactivating the modePressing the “2” key on the ten-key pad again while “CF SET” isdisplayed makes the mode ineffective.Pressing the CF key again while “CF SET” is displayed makes all thedetection methods ineffective.

NOTE･If this mode is used for counting notes other than the Euro notes, erroneousdetection may occur. Please use this mode only for the Euro notes.･If this mode is used by 500 notes/min, erroneous detection may occur.Please use this mode only by 1000 or 1500 notes/min.

TROUBLE SHOOTING

18

⇒　When an error occurs, its corresponding error code is displayed on the Batch Number Display. Find thecause of error by the displayed error code and remove the cause according to the following procedure.

Errorcode Type of error Cause of error Procedure for removing the cause of error

1.　Remove notes from in the Hopper and/or Stacker.

2.　Open the upper part of the Hopper and remove thejammed note(s).

3.　Set all the removed notes into the Hopper again.

4.　Restart counting operation by pressing the　　RESTART key.

Jam A note is jammedin the machine.

CAUTION:Before the Hopper is opened, besure to switch off the machine

(EJ)

3

19

(CL1～CL5)

(EC)

Errorcode Type of error Cause of error Procedure for removing the cause of error

Check all the notes on the Hopper, then set themagain. Press the RESTART key to start countingoperation.

Double notedetection(Ed)

Abnormal note is mixedin the bundle of notesto be counted.Half note

detectionChained notedetectionBatch overstopIncorrectsetting ofnotesSensorcleaning

Set the bundle of notes correctly.Improper setting of notesin Hopper, or no notes areset in Hopper

Switch off the machine and refer to the displayed errorcode, then clean the parts indicated by the error code,as shown in the photo on page 23 with the brush.

Auto start sensor is dirty.

Note is in theStacker

Remove the note(s) left in the Stacker.Note(s) is remains inthe Stacker.

Sensorcleaning

Sensor(s) is dirty.

Abnormality

Switch off the machine once, then switch on it again.Abnormality occurs inthe unit.(Er1～Er8)

(Hp)

(EH)

(Eo)

(St)

Switch off the machine and refer to the displayed errorcode, then clean the parts indicated by the error code,as shown in the photo on page 23 with the brush.

20

⇒　CAUTIONIn case that many “dd errors” or “dd2 errors” happens, remove all notes from the Hopper and Stacker, andmake sure the condition of notes (holes, tear, folds, etc.) then align and set notes again.Refer to the Chapter 4“Precautions for Handling of Machine”

Errorcode

Procedure for removing the cause of error

Check the last note in the Stacker.DD note(s)detection

Different size notesare mixed.

Detectionimpossible

Check all notes in the Stacker, and then set themagain.

Abnormal notes aremixed.

Abnormal notes aremixed.

Type of error Cause of error

(dd)

(En1～En2)

(dd2)

DD note(s)detection

Different size notesare mixed.

Abnormal notes aremixed.

Check all notes in the Stacker, and then setthem again.

Check all notes in the Stacker, and then setthem again.

Check the last two notes in the Stacker.

21

Errorcode

Procedure for removing the cause of error

Check the last note in the Stacker.Suspiciousnote(s)detection

Suspicious note isdetected.

ExternalLights Error

External Lights are toobright.

Type of error Cause of error

(CF)

(EF1～EF2)

(CF2)

Abnormal notes areMixed.

Use the machine in a less bright environmentto avoid direct sunlight.

Check the last two notes in the Stacker.

PRECAUTIONS FOR HANDLING OF MACHINEHow to Set Bank Notes

22

4

⇒ Precautions related to proper setting ofbank notes to be counted

→Damp and/or badly stained notes should beavoided.

→Check that no foreign matter (piece of paper,paper clip, dust, etc.) is mixed in with bundleof notes.

→Folded or curled notes should be straightenedbefore they are set on the Hopper.

→For brick notes (bundle of new notes whichare stucked to each other by ink), bendand flex the stack before it is set on theHopper.

⇒　How to align the notes to be counted.

→Align the long and short edges of the notesby lightly tapping the stack; insufficientalignment may cause an operation error.

Damp and/orstained note

Curled note Folded note

Stack of notes mixedwith clip or piece ofpaper or rubber hand

○ ×

Piece of paperClip

Rubber hand

DAILY CLEANING OF THE MACHINE

23

⇒　Sensors are used for the counting system of this machine.As these sensors are of optical construction, the system may cause miscounting should dust, dirt, etc.stick to the sensors.Clean the sensors shown on the photo below with an brush when counting operation is finished.

⇒　Piece of paper, dust and/or trash etc. accumulated in the Hopper and/or stacker may be taken into themachine; this may cause a malfunction of the machine. Clean the Hopper and Stacker in the same way asabove.

Auto start sensor

Repeat sensorCounting sensor

　　CAUTION　　☆Clean the machine after turning off the power switch.　　☆Do not use chemicals for cleaning the machine.

5

IR sensor (GFB900 Series only)

SPECIFICATIONS

ACCESSORIES

24

●　Dimensions

●　Weight

●　Size of countable note

●　Counting speed

●　Feed system

●　Hopper capacity

●　Stacker capacity

●　Counting number display

●　Batch number display

●　Power source

●　Power consumption

● Buzzer(Except GFB-800 810 820)

275mm(W)×235mm(H)×230mm(D)

Approx. 5.5kg

Widthwise :50mm～85mmLengthwise:110mm～185mmThickness: 0.06mm～0.12mm

1800, 1500, 1000, 500 notes/min. (Four step system)

Roller friction system

300 sheets

200 sheets

Four digits LED (large type)

Three digits LED (small type)

AC100～240V 50/60Hz

1.2A(100～127V), 0.6A(220～240V)

Give an alarm when different denomination andcounterfeit note is detected

6

●　Power cord………………………1 pc.

● Operating instructions …………1 pc.

7