IM327 QSG M en 00manual.kenwood.com/files/53a3b9961d582.pdf · messages “To Cancel DEMO Press the volume knob” are displayed (approx. 15 seconds). Turn the Control knob and press

KDC-U7049BTKDC-U7049BTLKDC-U6049KDC-U6049LCD-RECEIVERQuick Start GuideAMCD接收机

快捷入门指南

B59-2064-00/00 (MW)© 2010 Kenwood Corporation All Rights Reserved.

IM327_QSG_M_en_00.indd 1IM327_QSG_M_en_00.indd 1 10/12/03 14:4410/12/03 14:44

2 | Quick Start Guide

Contents Before use

2 WARNING

To prevent injury or fire, take the

following precautions:• Stop the car before operating the unit.

• To prevent a short circuit, never put or

leave any metallic objects (such as coins

or metal tools) inside the unit.

¤ CAUTION• Adjust the volume so that you can hear

sounds outside the car. Driving with the

volume too high may cause an accident.

• Wipe off the dirt on the panel with a dry

silicon or soft cloth.

Failure to observe this precaution may

result in damage to the monitor or unit.”

Cleaning the connectorWipe off dirt on the connector of the unit

and panel. Use a cotton swab or cloth.

CondensationWhen the car is air-conditioned, moisture

may collect on the laser lens. This may cause

disc read errors. In this case, remove the disc

and wait for the moisture to evaporate.

Before use .................................................. 2

Preparations .............................................. 4

Basic operations ....................................... 5

Playing music (CD/USB/iPod).............. 6

Listening to the radio ............................ 7

Hands-free phoning ............................... 8

Installation accessories .......................10

Before installation .................................10

Connecting wires to terminals .........12

Installation/Removal of the unit ......14

Installation of the Microphone Unit ..................................................................15

Appendix .................................................15

¤ CAUTION

• Keep battery out of reach of children

and in original package until ready to

use. Dispose of used batteries promptly.

If swallowed contact physician

immediately.

• Do not leave the battery near fire or

under direct sunlight. A fire, explosion

or excessive heat generation may result.

• Do not set the remote control in hot

places such as on the dashboard.

• Danger of explosion if Lithium battery is

incorrectly replaced. Replace only with

the same or equivalent type.


English | 3

Notes• If you experience problems during

installation, consult your Kenwood dealer.

• When you purchase optional accessories,

check with your Kenwood dealer to make

sure that they work with your model and

in your area.

• Characters that conform to ISO 8859-1

can be displayed.

• To display characters in the following

language, additional setting is required.

KDC-U7049BT KDC-U7049BTL

- Chinese

Refer to “Chinese” of <Initial setting>

(page 22) (Instruction Manual).

• KDC-U6049 KDC-U6049L

- Arabic

- Persian

- Thai

Refer to “Language” of <Initial setting>

(page 22) (Instruction Manual).

• The illustrations of the display and the

panel appearing in this manual are

examples used to explain more clearly

how the controls are used. Therefore,

what appears on the display in the

illustrations may differ from what appears

on the display on the actual equipment,

and some of the illustrations on the

display may be inapplicable.

About discs used with this unit• This unit can only play the CDs with

.

• The following discs cannot be used:

- Discs that are not round

- Discs with coloring on the recording

surface or discs that are dirty

- Recordable/Rewritable disc that has

not been finalized (For the finalization

process, refer to your disc writing

software, and your disc recorder

instruction manual.)

- 8 cm (3 inch) disc (Attempt to

insert using an adapter can cause

malfunction.)

Handling discs• Do not touch the recording surface of

the disc.

• Do not stick tape etc. on the disc, or use a

disc with tape stuck on it.

• Do not use any accessories for the disc.

• Do not use any solvents to clean discs.

Use a dry silicon or soft cloth.

• Clean from the center of the disc and

move outward.

• When removing discs from this unit, pull

them out horizontally.

• Remove the rims from the center hole

and disc edge before inserting a disc.

How to reset your unitIf the unit fails to operate properly, press

the Reset button. The unit returns to factory

settings when the Reset button is pressed. Reset button



Preparations

Exit Demonstration ModeTurn off the demonstration mode when you use it for the first time after installation.

Press the Control knob to quit the

demonstration mode when the

messages “To Cancel DEMO Press the

volume knob” are displayed (approx. 15

seconds).

Turn the Control knob and press it

when the “YES” is displayed.

The demonstration mode can also be

canceled in the Function setting mode.

Refer to <Demonstration mode Setting>

(page 22) of Instruction manual

Adjusting the Clock

Press the [DISP] button several times to

display the clock.

Press the [DISP] button for at least 1

second.

Turn the Control knob to adjust the

hour, and then press the Control knob.

Turn the Control knob to adjust the

minute, and then press the Control

knob.

Control knob (Volume knob)Release

[DISP]

Detaching/ Reattaching the

Faceplate

Press the Release button.

¤• Remove the faceplate at once after

pressing the Release button; otherwise it

can fall down due to vibration.

• The faceplate is a precision piece of

equipment and can be damaged by

shocks or jolts.

• Keep the faceplate in its faceplate case

while detached.

• Do not place the faceplate (and the

faceplate case) in areas exposed to direct

sunlight, excessive heat or humidity. Also

avoid places with too much dust or the

possibility of water splashing.


English | 5

Basic operations

Power Turn the power ON by pressing the

[SRC] button.

Press the [SRC] button for at least 1

second to turn the power OFF.

Source selectionPress the [SRC] button each time

switches between sources.

Tuner (“TUNER”) ➜ USB (“USB”) or iPod

(“iPod”) ➜ CD (“CD”) ➜ Auxiliary Input

(“AUX”) ➜ Standby (“STANDBY”) ➜

Tuner...

When an optional accessory is

connected, the source name for each

device appears.

KDC-U6049 KDC-U6049L

Press the [iPod] button to switch the

source to iPod.

The source “iPod” and “CD” can be

selected when each source is ready to

play.

VolumeTurn the Control knob to adjust the

sound volume.

USB terminalUSB device or iPod can be connected.

CA-U1EX or KCA-iP102 (optional

accessories) is recommended to connect

a USB device or iPod.

[DISP] [LOG]

[SRC][ ] [iPod]

KDC-U6049

[ ] [ ]

KDC-U7049BTKDC-U6049LKDC-U7049BTL

Auxiliary input

USB terminalControl knob

Auxiliary inputPortable audio device can be connected

with the stereo mini-plug (3.5 mm ø).

Display selectionEvery time the [DISP] button is pressed,

the display switches among 5 types.

You can switch the information to be

displayed. Refer to <Display settings>

(page 16) of Instruction manual

Display scrollKeep the [DISP] button pressed down

to scroll through the CD or audio file text

display.

Log memory recallPreviously used functions are automatically logged in memory and displayed as the list.

Press the [LOG] button.

Turn the Control knob and press

it when the desired Log memory is

displayed.

To cancel Log memory recall, press

[ ].

Logs can be saved or deleted. Refer to

<Log memory> (page 15) of Instruction

manual.



Playing music (CD/USB/iPod)

Playing discInsert the disc in the Disc slot.

When inserted, the source is switched

automatically and a song starts playing.

Playing USB device/ iPodConnect a USB device or iPod to the USB

terminal.

When connected, the source is switched

automatically and a song starts playing.

Selecting an audio file folderPush the Control knob towards up or

down to select a folder.

Selecting a songPush the Control knob towards right or

left to select a song (track or file).

Fast Forward or Fast Backward of

the SongPress and hold the Control knob

towards right or left to fast-forward or

fast-backward the audio file containing

songs (tracks or files).

Pause and playPress the [ ] button to pause or

resume playing a song (track or file).

Music searchSearching for the song you want to play.

Press the [ ] button.

Search for music.

Operation type OperationMovement between items Turn the Control knob.

Selection of item Press the Control knob.

Return to previous item Press the [ ] button.

To cancel the music search operation of

Audio file or iPod, press the [ ] button

for at least 1 second.

Removing DiscPress the [0] button to eject a disc.

Removing USB devicePress the [SRC] button to switch the

source to the device other than USB, and

then remove the USB device.

Data contained in the USB device may

be damaged when you remove it while it

is used as the active source.

[SRC]

[ ]

[0][ ]

USB Terminal

Control knob Disc slot


English | 7

Listening to the radio

Selecting a tuner sourcePress the [SRC] button to select “TUNER”.

Selecting the bandPush the Control knob towards down to

change the band (FM or AM).

Selecting a stationPush the Control knob leftward and

rightward to select the station you want

to listen to.

The tuning mode can be changed. Refer

to <Seek mode setting> (page 13) of

Instruction manual

Station preset memory

Push the Control knob towards down to


Push the Control knob leftward and

rightward to select the station you want

to memory.

Press the [PRESET] button.

Press the [PRESET] button again to

enter the Mix Station preset mode. In

this mode, FM and AM can be saved

in the same preset layer, which allows

you to recall the desired station without

switching the bands or tuner sources.

Maximum of 6 stations can be preset in

the Mix Station preset mode.

Turn the Control knob to select preset

number (FM: “01” – “18”, AM: “01” – “06”),

and then press the Control knob for at

least 2 seconds.

Recalling the stations in the

memory

Push the Control knob towards down to


Press the [PRESET] button.

Turn the Control knob to select preset

number (FM: “01” – “18”, AM: “01” – “06”),

and then press the Control knob.

[SRC] [PRESET]Control knob



Hands-free phoning

Registering cell-phoneRegister your Bluetooth cell-phone in this unit.


Press the [ ] button for at least 1

second.

The search for a cell-phone starts. It

takes a while (tens of seconds or several

minutes) to complete.

Press the Control knob when the model

name of a cell-phone to use is displayed.

Enter the PIN code of your cell-phone.

Operation type OperationSelect the numbers. Turn the Control knob.

Move to the next digit. Push the Control knob

towards right.

Delete the last digit. Push the Control knob

towards left.

Transmit the PIN code. Press the Control knob.

The connection to your cell-phone starts,

after a while “HF Connect” is displayed,

and then returns to the previous source.

When registration of your cell-phone is

complete, the phone book of the cell-

phone is automatically downloaded

to this unit. (If the phone book has not

been downloaded to this unit, operate

the cell-phone to download it.)


By operating the cell-phone, register

the hands-free unit (pairing). Select

“KCA-BT200” or “KCA-BT300” from the list

of connected units.

Enter the PIN code of this unit from the

cell-phone.

The PIN code of this unit is “0000” by

default.

When registration of your cell-phone is

complete, the phone book of the cell-

phone is automatically downloaded

to this unit. (If the phone book has not

been downloaded to this unit, operate

the cell-phone to download it.)

Error code list

• “Device Full”:

5 Bluetooth devices have already been

registered. No more Bluetooth devices are

registered.

• “PIN Code NG”:

The PIN code is wrong.

• “Connect NG”:

The unit cannot be connected to the

device.

• “Pairing Failed”:

Pairing error.

• “Confirm phone”:

Your cell-phone prompts you to confirm.

[LOG]

[SRC] [iPod]

KDC-U6049

[ ] [ ]


Control knob

Function of KDC-U7049BT, KDC-U7049BTL, KCA-BT200/BT300 (Optional Accessory)


English | 9

Calling a number in the Phone

bookDial the phone number in the phone book of your cell phone. If the phone book has not been downloaded to this unit, operate the cell-phone to download it.




Press the [LOG] button for at least 1

second.

Turn the Control knob and press it

when the “Phone Book” is displayed.

Turn the Control knob to select phone

number.

Push the Control knob towards right

or left to select the name of the called

party.

Operation type OperationSelect the Phone number. Turn the Control knob.

Select the initial. Push the Control knob

towards up or down.

Determine the Phone number. Press the Control knob.




Press the Control knob.

Answering a phone call KDC-U7049BT KDC-U7049BTL



Press the Control knob.

Disconnecting a call KDC-U7049BT KDC-U7049BTL



Press the [SRC] button.



2 WARNING • The unit can only be installed in a car with

a 12V DC power supply, negative ground.

• If you connect the ignition wire (red)

and the battery wire (yellow) to the car

chassis (ground), you may cause a short

circuit, that in turn may start a fire. Always

connect those wires to the power source

running through the fuse box.

¤ CAUTION

• Install this unit in the console of your

vehicle.

• Do not touch the metal part of this unit

during and shortly after the use of the

unit. Metal part such as the heat sink and

enclosure become hot.

• Mounting and wiring this product

requires skills and experience. For safety’s

sake, leave the mounting and wiring work

to professionals.

• If you experience problems during

installation, consult your Kenwood dealer.

Disconnect the battery’s negative terminal

and make all electrical connections before

installing the unit.

• Insulate unconnected wires with vinyl

tape or other similar materials. To prevent

a short circuit, do not remove the caps on

the ends of the unconnected wires or the

terminals.

• Be sure to ground this unit to the car’s

chassis again after installation.

• If the fuse blows, first make sure the wires

are not touching to cause a short circuit,

then replace the old fuse with one with

the same rating.

• When only two speakers are being

connected to the system, connect the

connectors either to both the front

output terminals or to both the rear

output terminals (do not mix front and

rear). For example, if you connect the +

Before installation Installation accessories

1

.....1

2

.....2

3

.....4

4

.....4

5 (KDC-U7049BT, KDC-U7049BTL only)

.....1 (3m)


English | 11

connector of the left speaker to a front

output terminal, do not connect the -

connector to a rear output terminal.

• Connect the speaker wires correctly to the

terminals to which they correspond. The

unit may be damaged or fail to work if

you share the - wires or ground them to

any metal part in the car.

• Do not use your own screws. Use only

the screws provided. If you use the wrong

screws, you could damage the unit.

• If your car’s ignition does not have an ACC

position, connect the ignition wires to a

power source that can be turned on and

off with the ignition key. If you connect

the ignition wire to a power source with

a constant voltage supply, as with battery

wires, the battery may die.

• If the console has a lid, make sure to

install the unit so that the faceplate will

not hit the lid when closing and opening.

• After the unit is installed, check whether

the brake lamps, blinkers, wipers, etc. on

the car are working properly.

• Mount the unit so that the mounting

angle is 30° or less.

• Reception may drop if there are metal

objects near the Bluetooth antenna.

(KDC-U7049BT, KDC-U7049BTL only)

Bluetooth antenna unit

For Good ReceptionTo assure good reception, note the

following:

• Communicate with the cell-phone within

the line-of-sight distance of 10 m (30

ft). The communication range becomes

shorter depending on the surrounding

environment. The communication

range also becomes shorter when there

is an obstacle between this unit and

the cell-phone. The above maximum

communication range (10 m) is not

always assured.

• A broadcast station or walkie-talkie

located nearby can interfere with

communication due to too strong signal.


–+


Connecting wires to terminals

White/Black

Gray/Black

Green/Black

Purple/Black

White

Gray

Green

Purple

To front left speaker

To front right speaker

To rear right speaker

To rear left speaker

To Kenwood disc changer/ External optional

accessory

⁄ To connect these leads, refer to the relevant instruction manuals.

Red (Ignition wire)

Yellow (Battery wire)

Black (Ground wire) · (To car chassis)

Ignition key

switch

Car fuse box (Main fuse)

ACC

Car fuse box

Battery

⁄• Speaker Impedance: 4 – 8 Ω

• USB terminal Maximum Supply current: 500 mA


P.CONT

ILLUMI

REMOTE CONT

REMOTE INPUTSTEERING WHEEL

ANT. CONT

MUTE

LR

LR

English | 13

FM/AM antenna input

Front output

Fuse (10A)

Sub Woofer output

Rear output

Wiring harness

(Accessory1)

If no connections are made, do not let the wire come out from

the tab.

Blue/White

(Power control wire)

Blue (Antenna control wire)

Orange/ White

(Dimmer control wire)

When using the optional power amplifier,

connect to its power control terminal.

To car light control switch

Depending on what antenna you are

using, connect either to the control

terminal of the motor antenna, or to the

power terminal for the booster amplifier of

the film-type or short pole type antenna.

Brown (Mute control wire)

To use the steering wheel remote control feature, an exclusive remote adapter (not supplied) that matches your car is required.

Light Blue/ Yellow

(Steering remote control wire)

Connect to the terminal that is grounded

when either the telephone rings or during

conversation. (KDC-U6049, KDC-U6049L

only)

⁄ To connect the Kenwood navigation system, consult your navigation manual.

Microphone (Accessory5)

(KDC-U7049BT, KDC-U7049BTL only)



Installation/Removal of the unit

Non-Japanese cars

Bend the tabs of the mounting sleeve with a screwdriver or similar utensil and attach it in place.

⁄• Make sure that the unit is installed

securely in place. If the unit is unstable, it

may malfunction (for example, the sound

may skip).

Japanese cars Refer to the section <Removing the hard

rubber frame> and then remove the

hard rubber frame.

Align the holes in the unit (two locations

on each side) with the vehicle mounting

bracket and secure the unit with the

accessory screws.

8 mm MAX.

ø5mm ø5mm

8mm MAX.

T

N T

N

T/N

T: Toyota carsN: Nissan cars

Accessory3...for Nissan carAccessory4...for Toyota car

3 4

Removing the hard rubber frame Engage the catch pins on the removal

tool and remove the two locks on the

upper level.

Lift up and pull the frame forward as

shown in the figure.

CatchLock

Removal tool (Accessory2)

When the upper level is removed,

remove the lower two locations.

⁄• The frame can be removed from the

bottom side in the same manner.

Removing the unit Refer to the section <Removing the hard

rubber frame> and then remove the

hard rubber frame.

Remove the faceplate.

Insert the two removal tools deeply into

the slots on each side, as shown.

Lower the removal tool toward the

bottom, and pull out the unit halfway

while pressing towards the inside.Accessory2

¤• Be careful to avoid injury from the catch

pins on the removal tool.

Pull the unit all the way out with your

hands, being careful not to drop it.


English | 15

Installation of the Microphone Unit

Check the installation position of the

microphone (accessory 5).

Remove oil and other dirt from the

installation surface.

Install the microphone.

Wire the cable up to the unit with it

secured at several positions using tape

or the like.

⁄• Install the microphone as far as possible

from the cell-phone.

Peel the release coated paper of double-face adhesive tape to fix on the place shown above.

Adjust the direction of the microphone to the driver.

Fix a cable with a commercial item of tape.

Accessory5

Appendix

About Audio file• Playable Audio file

AAC-LC (.m4a), MP3 (.mp3), WMA (.wma)

• Playable disc media

CD-R/RW/ROM

• Playable disc file format

ISO 9660 Level 1/2, Joliet, Romeo, Long

file name.

• Playable USB device

USB mass storage class

• Playable USB device file system

FAT16, FAT32

An online manual about

audio files is put on the site,

www.kenwood.com/cs/ce/audiofile/.

iPod/iPhone that can be connected

to this unitMade for

• iPod touch (4th generation)

• iPod touch (3rd generation)

• iPod touch (2nd generation)

• iPod touch (1st generation)

• iPod classic

• iPod with video

• iPod nano (6th generation)



• iPod nano (3rd generation)

• iPod nano (2nd generation)

• iPod nano (1st generation)

• iPhone 4

• iPhone 3GS

• iPhone 3G

• iPhone

For information on the compatibility of

iPod/iPhone software, visit www.kenwood.

com/cs/ce/ipod/.

KDC-U7049BT, KDC-U7049BTL only




English | 17

• “Made for iPod” and “Made for iPhone”

mean that an electronic accessory has been

designed to connect specifically to iPod or

iPhone, respectively, and has been certified

by the developer to meet Apple performance

standards. Apple is not responsible for the

operation of this device or its compliance with

safety and regulatory standards. Please note

that the use of this accessory with iPod or

iPhone may affect wireless performance.

• iPhone, iPod, iPod classic, iPod nano, and iPod

touch are trademarks of Apple Inc., registered

in the U.S. and other countries.

• The “AAC” logo is a trademark of Dolby

Laboratories.

• The Bluetooth word mark and logos are

owned by the Bluetooth SIG, Inc. and any

use of such marks by Kenwood Corporation

is under license. Other trademarks and trade

names are those of their respective owners.

This symbol mark indicates that

Kenwood manufactured this

product so as to decrease harmful

infl uence on the environment.

The marking of products using lasers

(Except for some areas)

CLASS 1

LASER PRODUCT

The label is attached to the chassis/case and says

that the component uses laser beams that have

been classified as Class 1. It means that the unit

is utilizing laser beams that are of a weaker class.

There is no danger of hazardous radiation outside

the unit.


18 | 快捷入门指南

目录使用之前

2 警告为了防止受伤或火灾，请遵守下列注意事项:・操作本机之前，请将汽车停下。・为了防止短路等事故，请勿将金属物品(硬币、工具等)掉落在装置中。

¤ 小心・请将音量调节到能够听到车外声音的程度。如果在驾驶时音量过大，可能导致发生事故。

・请使用干燥的硅布或软布擦拭面板上的灰尘。

不遵守本注意事项可能导致显示器或本机损坏。

清洁连接器请使用棉签或布擦拭本机和面板上的灰尘。

结露使用汽车空调时，湿气可能在激光透镜上结露，造成光盘读取错误。这时，请取出光盘等候湿气蒸发。

使用之前....................................................... 18

准备................................................................. 20

基本操作....................................................... 21

播放音乐.(CD/USB/iPod)........................ 22

收听广播....................................................... 23

免提通话....................................................... 24

安装附件....................................................... 26

安装之前....................................................... 26

将导线与端子连接.................................... 28

本机的安装/拆卸........................................ 30

麦克风的安装.............................................. 31

附录................................................................ 31

¤ 注意

・请将电池放在儿童拿不到的地方，并且在使用之前不要打开原包装。请妥善处理旧电池。万一误吞了电池，请立即与医生取得联系。

・不得使电池靠近明火或放在直射阳光下，否则可能导致火灾、爆炸或产生过热。

・不要将遥控器放在仪表盘等较热的位置。

・如果错误地更换锂电池，可能发生爆炸。仅限使用相同或同等类型的电池更换。

IM327_QSG_M_CHS.indd 18 10/12/03 11:03

中文 | 19

使用之前

说明・安装发生困难时，请与建伍经销商洽谈。・当购买选购附件时，请与建伍经销商洽谈，确认选购附件是否适合您的机型以及能否在您的地区使用。

・可显示符合ISO8859-1的字符。・为了使用下列语言显示字符，需要另行设定。


-中国语

请参照"Chinese"的<初始设定>(第22页)(使用说明书)。


-阿拉伯语

-波斯语

-泰语

请参照"Language"的<初始设定>(第22页)(使用说明书)。

・在本说明书中采用的显示和面板的插图是为了更加明确地举例说明控制的使用方法。因此，在插图中出现的显示可能与实际装置的显示有所不同，并且某些显示的插图可能不适用。

关于本机使用的光盘・本机仅能够播放具备下列标志

的CD。

・下列光盘无法使用: -非圆形光盘

-存储面上附有颜色或脏污的光盘

-未终结的可记录/可重写光盘 (有关终结处理，请参照光盘录制软件或录制设备的使用说明书。)

-8cm(3英寸)光盘(如果试图使用适配器插入将导致故障。)

光盘的使用方法・请不要触摸光盘的存储面。・请不要在光盘上粘贴胶带等，也不要使用贴有胶带的光盘。

・请不要使用光盘附件。・请不要使用溶剂清洁光盘。请使用干燥的硅布或软布擦拭。

・请从光盘的中心向外侧擦拭。・从本机中取出光盘时，请将光盘水平拉出。

・插入光盘之前，请去除光盘中心孔和光盘边缘的毛刺。

本机的复位方法如果本机无法正常工作，请按下复位按钮。按下复位按钮后，本机恢复到出厂设定状态。

复位按钮

IM327_QSG_M_CHS.indd 19 10/12/03 11:03


准备

退出演示模式安装后第一次使用本机时，请取消演示模式。

1 当显示 "To Cancel DEMO Press thevolume knob" (按下音量旋钮取消演示模式) 消息时 (大约15秒钟)，按下控制旋钮取消演示模式。

2 旋转控制旋钮，当显示 "YES" (是) 时按下。演示模式也可以通过功能设定模式取消。请参照使用说明书的 <演示模式设定>(第22页)。

调节时钟

1 数次按下[DISP].按钮显示时钟。2 按下[DISP].按钮1秒钟以上。3 旋转控制旋钮调节小时，然后按下控制旋钮。

4 旋转控制旋钮调节分钟，然后按下控制旋钮。

控制旋钮 (音量旋钮)拆卸按钮

[DISP]

取下/重新安装面板

按下释放按钮。

¤・按下释放按钮后，请立即取下面板。如果面板没有取下，则可能由于震动等落下。

・面板是精密的设备部件，可能由于震动和颠簸而损坏。

・面板拆下后，应保存在面板盒中。・不得将面板 (或面板盒) 暴露在直射的阳光下或者放在温度过高或湿度过高的环境。并且应避免过多的灰尘和可能溅到水。

IM327_QSG_M_CHS.indd 20 10/12/03 11:03

中文 | 21

基本操作

电源按下[SRC].按钮接通电源。按下[SRC].按钮1秒钟以上，电源切断。

选择信号源每次按下 [SRC].按钮，即在信号源之间切换。调谐器("TUNER")➜USB("USB")或iPod("iPod")➜CD("CD")➜辅助输入("AUX")➜待机("STANDBY")➜调谐器...当连接了选购附件时，出现各装置的信号源名称。


按下[iPod].按钮，将信号源切换到iPod。"iPod"和"CD"信号源的播放准备就绪后，才可以选择该信号源。

音量旋转控制旋钮调节音量。

USB端子可连接USB装置或iPod。建议使用CA-U1EX或KCA-iP102(选购附件)连接USB装置或iPod。

[DISP] [LOG]

[SRC][ ] [iPod]

KDC-U6049

[ ] [ ]


辅助输入

USB端子控制旋钮

辅助输入可以使用立体声微型插头(直径3.5mm)连接携带式音响装置。

显示选择每次按下 [DISP]. 按钮，显示即在5种类型之间切换。可以切换显示的信息。请参照使用说明书的<显示设定>(第16页)。

滚动显示向下按住[DISP].按钮，滚动显示CD或音响文件文本。

记录存储的调出以前使用的功能被自动记录在存储器中，并列表显示。

1 按下[LOG].按钮。2 旋转控制旋钮，当显示需要的记录存储时按下。取消记录存储调出时，按下[. .]。记录可保存或删除。请参照使用说明书的<记录存储>(第15页)。

IM327_QSG_M_CHS.indd 21 10/12/03 11:03


播放音乐 (CD/USB/iPod)

播放光盘向光盘槽插入光盘。插入后信号源自动切换，开始播放歌曲。

播放USB装置/iPod将USB装置或iPod与USB端子连接。连接后信号源自动切换，开始播放歌曲。

选择音频文件夹向上或向下按下控制旋钮选择文件夹。

选择歌曲向右或向左按下控制旋钮选择歌曲(音轨或文件)。

歌曲的快进或快退向右或向左按住控制旋钮，快进或快退含歌曲的音频文件(音轨或文件)。

暂停和播放按下[ ].按钮，暂停或恢复播放歌曲(音轨或文件)。

音乐搜索搜索需要播放的歌曲。

1 按下[. .]按钮。2 搜索音乐。操作类型操作

在项目之间移动旋转控制旋钮。

项目选择按下控制旋钮。

返回前一个项目按下[ ]按钮。

取消音频文件或iPod的音乐搜索操作时，按下[. .]按钮1秒钟以上。

取出光盘按下[0]按钮弹出光盘。

拆除USB装置按下[SRC]按钮，将信号源切换到USB以外的装置，然后拆除USB装置。如果在USB装置作为有效信号源使用时拆除，USB装置内的数据可能会损坏。

[SRC]

[ ]

[0][ ]

USB端子

控制旋钮光盘槽

IM327_QSG_M_CHS.indd 22 10/12/03 11:03

中文 | 23

收听广播

选择调谐器信号源按下[SRC]按钮选择"TUNER"(调谐器)。

选择波段向下按下控制旋钮选择波段(FM或AM)。

选择电台向左或向右按下控制旋钮，选择需要收听的电台。可以改变调谐模式。请参照使用说明书的<搜索模式设定>(第13页)。

电台预设存储

1 向下按下控制旋钮选择波段(FM或AM)。

2 向左或向右按下控制旋钮选择需要存储的电台。

3 按下[PRESET]按钮。再次按下 [PRESET] 按钮进入混合电台预设模式。在该模式，FM和AM可保存在相同的预设层级，从而可呼出需要的电台，无须切换波段或调谐器信号源。最多可对混合电台预设模式预设6个电台。

4 旋转控制旋钮选择预设号码(M:"01"-"18",AM:"01"-"06")，然后按下控制旋钮2秒钟以上。

呼出存储的电台

1 向下按下控制旋钮选择波段(FM或AM)。

2 按下[PRESET].按钮。3 旋转控制旋钮选择预设号码(FM: "01"- "18",AM:"01"- "06")，然后按下控制旋钮。

[SRC] [PRESET]控制旋钮

IM327_QSG_M_CHS.indd 23 10/12/03 11:03


免提通话

登录手机向本机登录蓝牙 (Bluetooth) 手机。


1 按下[. .]按钮1秒钟以上。开始搜索手机。需要等候片刻(数十秒至数分钟)。

2 显示了使用的手机型号后，按下控制旋钮。

3 输入手机的PIN代码。操作类型操作

选择号码。旋转控制旋钮。

移动到下一位。向右按下控制旋钮。

删除最后一位。向左按下控制旋钮。

传输PIN代码。按下控制旋钮。

开始与手机连接。显示了 "HFConnect" (免提连接)后，返回到以前的信号源。手机的登录结束时，手机的电话簿自动下载到本机。(如果电话簿没有下载到本机，请操作手机下载。)


1 操作手机，登录免提装置(配对)。从连接的装置列表中选择"KCA-BT200"或"KCA-BT300"。

2 通过手机输入本机的PIN代码。本机的初始PIN代码是"0000"。手机的登录结束时，手机的电话簿自动下载到本机。(如果电话簿没有下载到本机，请操作手机下载。)

错误代码一览表・"DeviceFull": 已经登录了5台蓝牙(Bluetooth)装置。无法再登录蓝牙(Bluetooth)装置。

・"PINCodeNG": PIN代码错误。

・"ConnectNG": 本机无法与该装置连接。

・"PairingFailed": 配对错误。

・"Confirmphone": 手机提示进行确认。

[LOG]

[SRC] [iPod]

KDC-U6049

[ ] [ ]


控制旋钮

KDC-U7049BT,KDC-U7049BTL,KCA-BT200/BT300的功能(选购附件)

IM327_QSG_M_CHS.indd 24 10/12/03 11:03

中文 | 25

免提通话

拨打电话簿中的号码拨打手机电话簿中的电话号码。如果电话簿没有下载到本机，请操作手机下载。

1 KDC-U7049BT KDC-U7049BTL

按下[. .].按钮。


按下[LOG]按钮1秒钟以上。

2 旋转控制旋钮，当显示"PhoneBook"(电话簿)后按下。

3 旋转控制旋钮选择电话号码。向右或向左按下控制旋钮，选择通话对方的姓名。

操作类型操作

选择电话号码。旋转控制旋钮。

选择首字母。向上或者向下按下控制旋钮。

确定电话号码。按下控制旋钮。

4 KDC-U7049BT KDC-U7049BTL

按下[. .].按钮。


按下控制旋钮。

接听电话 KDC-U7049BT KDC-U7049BTL

按下[. .].按钮。


按下控制旋钮。

中断通话 KDC-U7049BT KDC-U7049BTL

按下[. .]按钮。


按下[SRC]按钮。

IM327_QSG_M_CHS.indd 25 10/12/03 11:03


2警告・本机只能安装在使用负极接地12V DC电源的汽车上。

・如果将点火导线(红色)和蓄电池导线(黄色) 与汽车底盘 (接地) 连接，将造成短路，甚至可能发生火灾。应务必将这些导线通过保险丝盒与电源连接。

¤ 注意・请将本机安装在汽车的控制台。・在使用中和使用后的短时间内，不得触摸本机的金属部件。诸如散热器和壳体等金属部件较热。

・安装本产品和连接导线需要一定的技能和经验。为了保证安全，应请专业人员完成安装和连接导线作业。

・如果在安装中出现问题，请与建伍经销商洽谈。在安装本机前，拆除蓄电池负极端子的连接，然后再连接导线。

・使用聚氯乙烯绝缘带或其他类似材料绝缘未连接的导线。为了防止短路事故，请不要拆下附在未连接的导线和端子上的外罩。

・完成安装后，务必再次将本机与汽车底盘连接。

・如果保险丝烧断，请首先检查有无导线接触造成短路，然后使用与旧保险丝相同规格的保险丝更换。

・当系统仅连接两个扬声器时，请将两个扬声器的连接器都仅连接在前侧输出或后侧输出的其中之一 (不得前后混合)。例如，如果将左侧扬声器的+连接器与前侧输出端子连接，则不得将-连接器与后侧输出端子连接。

・请正确地将扬声器导线分别连接相应的扬声器端子上。如果共用负极 (－) 导线或将其与汽车的金属部件连接，可能造成本机损坏或无法正常工作。

・不得使用自备的螺丝。只能使用随机提供的螺丝。如果使用不适当的螺丝，将可能损坏本机。

安装之前安装附件

1

.....1

2

.....2

3

.....4

4

.....4

5(仅限KDC-U7049BT,KDC-U7049BTL)

.....1 (3m)

IM327_QSG_M_CHS.indd 26 10/12/03 11:03

中文 | 27

・如果汽车的点火系统没有ACC位置，请将点火导线连接在可通过点火钥匙接通/切断的电源上。如果将点火导线与诸如蓄电池导线等始终提供电压的电源连接，蓄电池将会耗尽。

・仪表板有盖子时，请务必在安装本机时使得面板的开闭操作不要碰撞盖子。

・安装结束后，请确认汽车制动灯、转向灯和雨刷等是否正常动作。

・本机安装角度不得大于30度。・如果有金属物体靠近蓝牙(Bluetooth)天线，接收可能发生中断。(仅限KDC-U7049BT,KDC-U7049BTL)

蓝牙.(Bluetooth).天线装置..

为了良好的接收为了保证良好接收，请注意下列事项:・与手机的通讯视线距离为10m (30英尺)之内。周围环境可能会使通讯范围缩小。

如果在本机和手机之间存在障碍物，通讯范围也会缩小。上述最大通讯距离(10m)并非保证值。

・由于附近的广播电台或对讲机的信号过强，将会对通讯造成干扰。

安装之前

IM327_QSG_M_CHS.indd 27 10/12/03 11:03

P.CONT

ILLUMI

REMOTE CONT


ANT. CONT

MUTE

–+

LR

LR


将导线与端子连接

白色/黑色

灰色/黑色

绿色/黑色

紫色/黑色

白色

灰色

绿色

紫色

向前置左扬声器

向前置右扬声器

向后置右扬声器

向后置左扬声器

至建伍光盘换片机/外部选购附件

⁄请参照相关的使用说明书连接这些导线。

红色(点火导线)

黄色(蓄电池导线)

黑色(接地线)·(至汽车底盘)

点火开关钥匙

汽车保险丝盒(主保险丝)

ACC

汽车保险丝盒

蓄电池

⁄・扬声器阻抗:4-8Ω・USB端子最大供电电流:500mA

IM327_QSG_M_CHS.indd 28 10/12/03 11:03

P.CONT

ILLUMI

REMOTE CONT


ANT. CONT

MUTE

–+

LR

LR

中文 | 29

将导线与端子连接

FM/AM天线输入

前侧输出

保险丝(10A)

重低音输出

后侧输出

电线束(附件1)

不连接时，请不要使得导线从护套中伸出。

蓝色/白色(电源控制导线)

蓝色(天线控制导线)

橙色/白色(调光器控制导线)

连接另售的功率放大器时，向功率放大器的功率控制端子连接。

至车灯控制开关

根据使用的天线，请与电动天线的控制端子、或薄膜型天线的增幅放大器电源端子或短棒型天线连接。

棕色(静音控制导线)

如果使用方向盘遥控控制功能，需要安装对应该汽车的专用遥控适配器(没有提供)。

淡蓝色/黄色(方向盘遥控控制导线)

与当电话铃响或通话时接地的端子连接。(仅限KDC-U6049,KDC-U6049L)

⁄连接建伍导航系统时，请参照导航系统的使用说明书。

黑色(接地线)·(至汽车底盘)

麦克风(附件5)(仅限KDC-U7049BT,KDC-U7049BTL)

IM327_QSG_M_CHS.indd 29 10/12/03 11:03


本机的安装/拆卸

非日本制造的汽车

使用螺丝刀等折弯安装套管凸耳部位，将其固定。

⁄・请切实固定本机。如本机安装不牢固，会造成跳音等故障。

日本制造的汽车1 请参照 <取下硬橡胶框> 部分，取下硬橡胶框。

2 将汽车安装支架对准本机的孔 (每侧两个位置)，然后使用附件螺丝紧固本机。

8 mm MAX.

ø5mm ø5mm

8mm MAX.

T

N T

N

T/N

T: 丰田牌汽车N: 日产牌汽车

附件3...用于日产牌汽车附件4...用于丰田牌汽车

3 4

取下硬橡胶框1 操作拆卸工具的凸耳，拆除上侧的两个锁扣。按图示要领将框向上抬，再向前拉动。

凸耳锁定装置

拆卸工具(附件2)

2 上侧拆除后，拆除下侧的两处位置。⁄・框架可以按照同样方法从下侧开始拆下。

本机的拆卸方法1 请参照 <取下硬橡胶框> 部分，取下硬橡胶框。

2 取下面板。3 如图所示，将两个拆卸工具深深插入两侧的槽内。

4 将拆卸工具向下降，靠近内侧，将装置拉出到中途。

附件2

¤・请注意不要被拆卸工具的凸耳碰伤。5 用手小心托住本机全部拉出，以免掉落。

IM327_QSG_M_CHS.indd 30 10/12/03 11:03

中文 | 31

麦克风的安装

1 检查麦克风的安装位置(附件5)。2 擦干净安装表面的油污和灰尘等。3 安装麦克风。4 将麦克风导线与本机连接，使用胶带等在数个位置进行固定。

⁄・请将麦克风安装在尽可能远离手机的位置。

揭下双面胶带的保护纸，粘贴在如图所示位置。

调节麦克风的方向朝向驾驶人员。

使用市售的胶带固定导线。

附件5

附录

关于音响文件・可播放的音响文件 AAC-LC(.m4a)、MP3(.mp3)、WMA(.wma)

・可播放的光盘媒体 CD-R/RW/ROM

・可播放的光盘文件格式 ISO9660Level1/2、Joliet、Romeo、长文件名称。

・可播放的USB装置 USB海量存储等级

・可播放的USB装置文件系统 FAT16、FAT32

有关音响文件的在线使用指南可以从www.kenwood.com/cs/ce/audiofile/网站获得。

可与本机连接的iPod/iPhoneMadefor・iPodtouch(4thgeneration)・iPodtouch(3rdgeneration)・iPodtouch(2ndgeneration)・iPodtouch(1stgeneration)・iPodclassic・iPodwithvideo・iPodnano(6thgeneration)・iPodnano(5thgeneration)・iPodnano(4thgeneration)・iPodnano(3rdgeneration)・iPodnano(2ndgeneration)・iPodnano(1stgeneration)・iPhone4・iPhone3GS・iPhone3G・iPhone关于iPod/iPhone软件的兼容性信息，请浏览www.kenwood.com/cs/ce/ipod/。

仅限KDC-U7049BT,KDC-U7049BTL

IM327_QSG_M_CHS.indd 31 10/12/03 11:03

・"MadeforiPod"and"MadeforiPhone"meanthatanelectronicaccessoryhasbeendesignedtoconnectspecificallytoiPodoriPhone,respectively,andhasbeencertifiedbythedevelopertomeetAppleperformancestandards.Appleisnotresponsiblefortheoperationofthisdeviceoritscompliancewithsafetyandregulatorystandards.PleasenotethattheuseofthisaccessorywithiPodoriPhonemayaffectwirelessperformance.

・iPhone,iPod,iPodclassic,iPodnano,andiPodtoucharetrademarksofAppleInc.,registeredintheU.S.andothercountries.

・The“AAC”logoisatrademarkofDolbyLaboratories.

・蓝牙名称标识和徽标由BluetoothSIG，Inc.拥有。建伍公司获得了该标识的使用许可。其他商标和商号分别由其拥有人拥有。

本象征标志表示，建伍公司制造的本产品有利于减少对环境的有害影响。

使用激光的产品标志 (部分地区除外)

CLASS 1 LASER PRODUCT

1类激光产品

贴附在机架或外盒上的标记，是表示该产品使

用了分类为CLASS1激光的标志，表明本装置利

用了最弱级的激光束，并无向装置外辐射的危

险。

产品中有毒有害物质或元素的名称及含量

部件名称

有毒有害物质或元素

铅 (Pb)

汞 (Hg)

镉 (Cd)

六价铬 (Cr(VI))

多溴联苯 (PBB)

多溴二苯醚(PBDE)

安装基板 × ○ ○ × ○ ○

框架 × ○ ○ × ○ ○

机芯（硬盘驱动器、DVD、CD等） × ○ ○ × ○ ○

其他（附件） × ○ ○ × ○ ○

○：表示该有毒有害物质在该部件所有均质材料中的含量均在 SJ/T11363-2006 标准规定的限量

要求以下。

×：表示该有毒有害物质至少在该部件的某一均质材料中的含量超出 SJ/T11363-2006 标准规定

的限量要求。

表示例

该标识中表示的数字为自生产日期开始对环境的保护期限、表示不会因产品

中含有的有毒有害物质或元素的外泄造成环境污染、以及对人体或财产造成

严重损害的年数。

该环境保护期限并不是对于性能、功能的保证期限。

在产品及电池等正常使用结束、进行废弃时，请遵守各地方政府的法律和规

定予以处理。

IM327_QSG_M_CHS.indd 32 10/12/03 11:03

Documents

IM327 QSG M en 00manual.kenwood.com/files/53a3b9961d582.pdf · messages “To Cancel DEMO Press the volume knob” are displayed (approx. 15 seconds). Turn the Control knob and press