Jehnert 75151 EBA Engl Web

Embed Size (px)

Citation preview

  • 8/18/2019 Jehnert 75151 EBA Engl Web

    1/16

    Sound Sound D E S I G N 

    JEHNERT

       A   U

       D   I

       A

       4   C

      a   b  r   i  o

    Montageanleitung

       M  o  n   t  a  g  e  a  n   l .   A  r   t .   7

       5   1   5   1   /   F   H   0   7 .   0

       3

    Artikel-Nr.  75151

    Jehnert Sound DesignEntwicklung undProduktion von

    Car-Audio-Systemen

    Heinrich-Hertz-Str. 1170794 Filderstadt

    Tel.: 0711-77 97 87- 87Fax: 0711-77 78 921

    e-mail: [email protected]

    installation instruction

         c     o     n     v     e     r       t        i        b        l     e

    prod. code

    Production of 

    Car-Audio-Systems

    Porsche Str. 1570794 Filderstadt

    Tel. 00 49 71 58 / 9 56 99-0Fax 00 49 71 58 / 9 56 99-10

    e-mail: [email protected]

  • 8/18/2019 Jehnert 75151 EBA Engl Web

    2/16

      Packliste ..............................................................................

    1. Demontage der Türverkleidung...............................................

    2. Montage des Hochtöners .......................................................

    3. Paneelanpassung ..................................................................

    4. Bearbeiten der Türverkleidung / Montage der Türpaneele..........

    5. Frequenzweichenmontage + Lautsprecherleitungen .................

    6. Dämmung der Türverkleidung / Fahrzeugtüren ........................

    7. Montage der Türverkleidung ..................................................

    8. Lautsprecheranschluss ..........................................................

      Lautsprecheranschluss - Schaltbild ........................................

    9. Montage der Lautsprecher-Abdeckblenden .............................

      Technische Informationen .....................................................

      Service / Fehlersuche............................................................

      Garantie .............................................................................

      Packliste ..............................................................................

    1. Demontage der Türverkleidung...............................................

    2. Montage des Hochtöners .......................................................

    3. Paneelanpassung ..................................................................

    4. Bearbeiten der Türverkleidung / Montage der Türpaneele..........

    5. Frequenzweichenmontage + Lautsprecherleitungen .................

    6. Dämmung der Türverkleidung / Fahrzeugtüren ........................

    7. Montage der Türverkleidung ..................................................

    8. Lautsprecheranschluss ..........................................................

      Lautsprecheranschluss - Schaltbild ........................................

    9. Montage der Lautsprecher-Abdeckblenden .............................

      Technische Informationen .....................................................

      Service / Fehlersuche............................................................

      Garantie .............................................................................

    Seite

    2

    3

    4

    5

    6

    7

    8

    9

    10

    11

    12

    13

    14

    15

      75151 - Audi A 4 Cabrio - 1 - © JEHNERT SOUND DESIGN

    I n h a l t s v e r z e i c h n i s  

    Besonders wichtige Hinweise enthalten folgende Markierung:

    Bitte folgen Sie den Anweisungen der Montageanleitung“Schritt f ür Schritt”

    und prüfen Sie den Packungsinhalt

      Packing list .......................................................................... 2

    1. Disassembly of the door lining .............................................. 3

    2. Installation midrange and tweeter in the dashboard ................ 4

    3. Panel alignment ................................................................... 5

    4. Handling of doorlining / Installation door panel ..................... 6

     

    page

     

    Crossover circuit - Speaker connection ..................................

    Insulation of the door lining / car doors .................................

    Installation of the door lining onto the car doors ....................

    Crossover circuit - Speaker connection ..................................

    Lodspeaker wiring diagram ..................................................

    Installation of the speaker-grills ............................................

    Technical Information ..........................................................

    Service / fault diagnoses .......................................................

    Guarantee ..........................................................................

    Particularly important notes contain the following remarks:

    Please follow the installation instructions“step by step”

    and check the package contents

    Speaker connection ...............................................................

    C o n t e n t s  

     

  • 8/18/2019 Jehnert 75151 EBA Engl Web

    3/16

    Verpackungseinheit    Checkliste

    Türpaneele, bezogen (rechts / links) 2

    Abdeck-Blenden, bezogen (rechts / links) 4

    Hochtöner 26 mm 2

    Mitteltöner 100 mm Q ( jewei ls mit 2 Blechschrauben am Paneel mont iert) 2

    Tieftöner 160 mm ( jewei ls mit 2 Blechschrauben am Paneel mont iert) 8

    Frequenzweichen (rechts / links) 2

    serieller Kabelsatz f ür Tieftöner (rechts / links)   je 1

    Kleinteile-Beutel: 

    Schrauben-Senkkopf, M 4 x 20 4

    Schrauben-Senkkopf, M 4 x 30 6

    6-Ktn.Mutter M 4 22

    Unterlagscheiben Ø 20mm 22

    Unterlagscheiben Ø 20mm als Distanzhilfe f ür Klettverschlüsse   4

    Blechschrauben, schwarz 3,9x13(f. Tieftöner)  8

    Klettband   à 2,5 cm (Reserve)   4

    Kleinteile-bereits montiert: 

    Klettverschlüsse + Klettband 16

    Schrauben-Senkkopf, M 4 x 20 2 Schrauben-Senkkopf, M 4 x 30 2

    Schrauben-Senkkopf, M 4 x 40 2

    Schrauben-Senkkopf, M 4 x 50 4

    Blechschrauben, schwarz 3,9 x 13 (f ür Tieftöner) 8

    Blechschrauben, schwarz 3,5 x 13 (4xMT+16xKlet tv. ) 20

    Die Ware wurde sorgf ältig verpackt und auf ihre Vollständigkeit geprüft. Bei Fehlmengen, Schäden oder Mängelbeachten Sie bitte unsere Garantieleistungen auf der Rückseite dieser Montageanleitung.

    Kleinteile-Beutel: 

    Packliste Art. 75151

     75151 - Audi A 4 Cabrio - 2 - © JEHNERT SOUND DESIGN

    Packing unit Check list  

    door panel, covered (right / left)   2

    Speaker grill, covered (right / left) 2

    Tweeter 26 mm (with perforated sheet metal,6.Ktn.Screw M4x8,Washer ø 12mm) 2

    Midrange 100 mm Q (each mounted on the panel with 4 Sheet metal-screws) 2

    Woofer 160 mm (each mounted on the panel with 2 Sheet metal-screws) 8

    Crossover (right / left) 2

    standard cables for subwoofer (right / left)   2

     

    Packing unit Check list  

    door panel, covered (right / left)   2

    Speaker grill, covered (right / left) 2

    Tweeter 26 mm (with perforated sheet metal,6.Ktn.Screw M4x8,Washer ø 12mm) 2

    Midrange 100 mm Q (each mounted on the panel with 4 Sheet metal-screws) 2

    Woofer 160 mm (each mounted on the panel with 2 Sheet metal-screws) 8

    Crossover (right / left) 2

    standard cables for subwoofer (right / left)   2

     

    (with perforated sheet metal, hex nut M4, washer Ø 12 mm)

    4165

    4

     

    ardware bag: 

     

    ardware bag: 

     Hexagon head screws, M 4 x 30Hexagon head screws, M 4 x 3020

     

    Hexagon head screws, M 4 x 30Hexagon head screws, M 4 x 30

    Hex nut M 4Hex nut M 4

    Washer Ø 20mm (incl. 4x as spacer for Velcro fastener)  Washer Ø 20mm (incl. 4x as spacer for Velcro fastener)   26

     

    Sheet metal screws, black 3,9x13 (f. woofer)   16

    Velcro strip à 2,5 cm (reserve) 4

     

    Sheet metal screws, black 3,9x13 (f. woofer)   16

    Velcro strip à 2,5 cm (reserve) 4

     

    8

     

    The product was carefully packed and checked for its completeness. If you find anything missing, damaged or

    defective, please notice our guarantee services on the back of these assembly instructions.

     

    The product was carefully packed and checked for its completeness. If you find anything missing, damaged or

    defective, please notice our guarantee services on the back of these assembly instructions.

     

  • 8/18/2019 Jehnert 75151 EBA Engl Web

    4/16

    1.5. Torx-Schraube (D) unter der Abdeckung der Schalterleiste/Fahrerseite

      bzw. Fensterheberschalter/Beifahrerseite entfernen.

    1.6. Schraube (E) am unteren Türverkleidungsrand entfernen.

    1.7. Türverkleidung vorsichtig nach vorne abnehmen und nach oben wegziehen.

    1.8. Türentriegelungsbowdenzug aushängen.

    1.9. Elektrischen Anschluß f ür Schaltleiste abstecken.

    1.10. Original-Lautsprecheranschluss abstecken und werkseitiger Tieftöner demontieren.

    1.11. Werkseitiges Kartenfach und Original-Lautsprecher entfernen:  Befestigungsnieten gebm. Abb. auf der Türverkleidungs-Rückseite abhebeln und  komplette Einheit abnehmen.

    Abb.: Türverkleidungsrückseite- Demontage werkseitiges Kartenfach

    1 . Demontage der T ü rverkleidung 

      75151 - Audi A 4 Cabrio - 3 - © JEHNERT SOUND DESIGN

    B

    A

    1.1. Fensterscheibe komplett herunterlassen.

    1.3. Darunterliegende 4 Schrauben (B1+2: Torxschr. / B3+4: Kreuzkopfschr.) entfernen.

    D

    1.2. Demontage der Holzleiste   (am Fixpunkt A beginnend!)

    • Seitenkanten (Abb. A+B) mit  einem Keil vorsichtig nach vorne  abdrücken.

    • in Richtung Türschloss schieben  und abziehen.

    1.4. Die Abdeckung der Schalter-

      leiste/Fahrerseite und Fenster-  heberschalter/Beifahrerseite  durch die Öffnung unterhalb  des Türgriffes herausdrücken.

    E

    D

    C1   C2

    C3   C4

    Roll down window completely.1.1.

    Remove the Bowden pull wire of the door latch lever.1.8.

    Disconnect the original loudspeaker plugs and dismount the original speaker.1.10.

    1. Disassembly of the door lining 

    Disassambly of the wooden ledge(start on xing point A!)• Carefully squeeze away the side

    edges ( see g. A+B) with a key.• Move it in direction of the

    door lock and lift it off.

    1.2.

    Disassambly of the wooden ledge(start on xing point A!)• Carefully squeeze away the side

    edges ( see g. A+B) with a key.• Move it in direction of the

    door lock and lift it off.

    1.4.

    Remove the 4 screws (B1+2 torx screw, B3+4 crosshead screw).1.3.

    Remove the torx screw (D) under the grill of the switch board / driver’s side,

    respectively the switch for the window lifter / co-driver’s side.

    1.5.

    Remove the screw (E) on the lower edge of the door card.1.6.

    Carefully take the door card forward away and pull it upward away.1.7.

    Unplug the switch board.1.9.

    Remove the original tray and the original speakers: pry out the rivets on the

    backside of the door card and take away the whole unit (see g.).

    1.11.

    g.: disassembly original tray – backside of the door card

  • 8/18/2019 Jehnert 75151 EBA Engl Web

    5/16

    2.1. Plastikrahmen des Hochton-Gitters mit einem Keil ausklipsen und

      abnehmen.

    2.2. Werkseitiger Hochtöner entfernen und Lautsprecher-Anschluß abstecken.

    2.3. JEHNERT-Hochtöner mit Lautsprecherkabel (1,5 - 4mm ) verkabeln  Kabellänge: bis zur Frequenzweiche  Montage unterhalb des Armaturenbrettes

    2.4. Das Langlochblech am Hochtöner mittels Unterlagscheibe und 6Ktn.  Schraube befestigen.

    2.5. Hochtöner mit dem Langlochblech in die werkseitige Einbauöffnungeinsetzen, Lautsprecherkabel zum Frequenzweichen-Montageort f ühren,

      Langlochblech befestigen..

    Akustische Empfehlung:   Hochtöner angewinkelt zum Innen-Rückspiegel justieren.  (Nicht zur Fahrer - oder Beifahrerseite!)

      75151 - Audi A 4 Cabrio - 4 - © JEHNERT SOUND DESIGN

    2 . Montage des Hocht ö ners im Armaturenbrett 

    � Acoustic recommendation:Adjust the tweeter in an angular position to the inner reviewmirror --> not in direction of the driver‘s or co-driver‘s side!

    Dismount the original speaker grill and the tweeter in the originalmount of the dashboard. Unplug the cable (original tweeter and cable

    will not be used any more).

    2.1.

    Adapt the JEHNERT-tweeter cable with the speaker cable (1,5 - 4 qmm),length of cable up to where the crossover is installed under the dash-board.

    2.2.

    2. Tweeter installation in the dashboard 

    Afx the perforated sheet with washer and hexagon screw on thetweeter.

    2.3.

    Insert the tweeter with perforated sheet in the original place, lead thespeaker cable to the mounting position of the crossover and afx theperforated sheet.

    2.4.

  • 8/18/2019 Jehnert 75151 EBA Engl Web

    6/16

  • 8/18/2019 Jehnert 75151 EBA Engl Web

    7/16

    1. Zur Positionierung der Befestigungspunkte 1-11 das passgenau ausgerichtete  Paneel als Schablone verwenden:

    • Markierung Befestigungspunkt 1-6_ bereits im Paneel montiert: 

      durch Aufdrü

    cken des Paneels auf der Tü

    rververkleidung - Abdruck sichtbar•  Markierung der Befestigungspunkte 7-11:   mit einem dünnen Vorstecher auf der Türverkleidung markieren.

    2. Die Lautsprecheröffnungen auf der Türverkleidung anzeichnen.

    3. Paneel wieder abnehmen. Die angezeichneten Lautsprecheröffnungen  auf der Türverkleidung mit einer Stichsäge ausschneiden.

    4. Für die einzusetzenden Schrauben die Bohrungen gemäß Markierungen  mit einem 6mm-Bohrer vornehmen.

    5. Mitgelieferte M4-Schrauben eindrehen. Türpaneel mit der Türver-  kleidung durch leichtes Festschrauben aller 11x M4-Schrauben fixieren.  Alle Schrauben mit den Unterlagscheiben und Muttern sichern.

    6. Nochmals Passgenauigkeit überprüfen und Schrauben festziehen:

    Alle Schnittkanten des Paneels m ü ssen umlaufend ohne Spalt 

    auf der T ü rverkleidung anliegen.

    4. Bearbeitung der T ü rverkleidung / Montage der T ü rpaneele 

      75151 - Audi A 4 Cabrio - 6 - © JEHNERT SOUND DESIGN

           

    M 4  x 3 0 

    m o n t ie r t 

    M 4  x 5 0 

    m o n ti er t M 4  x 50 

    m o n ti e r t 

    M 4  x 5 0 

    m on t i e r t 

    M 4  x 4 0 

    m on t i e r t 

    M 4  x 2 0 

    m o n t ie r t 

    1   2   3  4   5

    7910   8

    M 4  x  2 0 M 4  x  2 0  M 4  x  3 0 

    M 4  x  3 0 

       

    6

    M 4  x  3 0 

    11

    1. use the precisely aligned panel as template in order to mark fastening points 1- 1

    • marking of fixing points 1-3_ premounted in the panel: Press the panel to the door lining makes the screw points visible

    • marking of fixing points  4-11: 

      use a thin awl to set the marks on the door-lining

    2. draw the speakers’ cut-outs onto the door-lining.

    3. remove the panel again.  cut out holes for loudspeakers along the marking with a compass saw (see fig.)

     

    4. Handling of door lining / Panel installation - Fastening 

     

     

    1-6,

    7-11:

     

    4. use a 6mm drill for the screws according to the marks set before

    5. Screw in the screws supplied with. Affix the door build to the door-lining.  Screw all 8 x screws only hand-tight .  Secure all screws with the washers and nuts.

    6. check again for precise fitting and tighten screws.check all screw connections:  In order to avoid damages to the car door, check

      the length of the staybolts on the backside of the door lining once again and  possibly shorten them.

    All cutting edges of the panel must fit to the door lining snugly all around without gap 

     

     

    screws only hand-tight . 

  • 8/18/2019 Jehnert 75151 EBA Engl Web

    8/16

    5. Lautsprecherleitungen 

     Lautsprecherkabel in die Fahrzeugt ü ren f ü hren: 

     5.1 Regenschutzfolie vorsichtig entfernen (s.Abb. Seite 8)

     5.2 Dämmung der Fahrzeugtüren - Maßnahmen Vibrationsgeräusche (s.S.8)

     5.3 Lautsprecherkabel verlegen:

      1 x Lautsprecherkabel (1,5 - 4 mm2) in die Fahrzeugtüre f ühren

     5.4 Regenschutzfolie wieder passgenau anbringen

      75151 - Audi A 4 Cabrio - 7 - © JEHNERT SOUND DESIGN

     

    5.2. Installation of loudspeaker cables 

    5.1. carefully remove the moisture protection foil

    5.2. insulation of the door lining - Important tips against vibration-noise (s.page.8)

    5.3. install cables:

      Lead 1 speaker cable (1,5 - 2,5 m 2) from amplifier into the door.

    5.4. reinstall the moisture protection foil

    5. Loudspeaker cables

    75151

  • 8/18/2019 Jehnert 75151 EBA Engl Web

    9/16

      75153 - Audi A 4 models from 2001 - 8 - © JEHNERT SOUND DESIGN

    6. insulation of the door lining 

    Important tip: 

      the use of 2x16mm mid-woofer /side may cause vibrations which lead to  annoying rattle noises in the car door

    some helpful tips: •  use our self-adhesive insulation fleece (art.no.: 27000) or a foam material for  the backside of the door lining (see fig. above) or

    •  stabilize the backside of the door lining by means of a special material

    (Glass Fibre Filler or stiffening material)i mportant: keep the cut-outs for the door-airbags and speakers open 

    •  affix the *backside of the inner door metal with self-adhesive asphalt mats (see fig. * )

    •  by knocking on the car door, vibrations caused by mechanic parts (e.g. Bowden pull wire etc. )  and wiring harness may be found out. Cover these parts with foamed material, felt or  something like that

    •  cut off overlapping cable tie (rattle noise)

    •  adhere felt or foamed material under the original wiring harness

    !

    Important: 

    No insulation material behind - loudspeaker - door latch lever - (fig. A): drill a hole for the   installation clip 

    fig.: backside of the door lining – insulation with our article no.: 27000

    moisture protection foil 

    front side of inner door metal 

    * door metal outside   = back side of the   inner door metal 

    attention  –  danger !! 

    No insulation behind the side-airbags (fig. B) 

  • 8/18/2019 Jehnert 75151 EBA Engl Web

    10/16

    7. Montage der T ü rverkleidung 

    7.1. Türverkleidung oben in die Türschachtleiste einhängen

    7.2. In umgekehrter Reihenfolge wie auf Seite 3 beschrieben wieder befestigen.

    7.3. Regenschutzfolie f ür die Tieftöner u-f örmig einschneiden und seitliche

    Schnittkanten zur Vermeidung von Vibrationsgeräuschen der Folie

      stabilisieren (z.B. mit Packband)

      75151 - Audi A 4 Cabrio - 9 - © JEHNERT SOUND DESIGN

       

    7. Installation of the door lining onto car door 

    7.1. Put in the door lining in the sealing above.

    7.2. Fit the door lining in contrary order (described on page 3).

    7.3. Cut (like a U) the moisture protection foil and stabilize

    the edges of the foil against vibrations.

      (for example with packing tape)

     

  • 8/18/2019 Jehnert 75151 EBA Engl Web

    11/16

      8. Frequenzweichenmontage und Lautsprecheranschluss 

      5.1.1 Frequenzweichen vorverkabeln - vgl. Abb. Seite 11.  5.2.1 Gehäuse entfernen und hinter dem Steg des Türpaneels zwischen  Türverkleidung und Türpaneel einschieben und sicheren Sitz

      befestigen.

      Tief- und Mitteltöner einsetzen und alle Lautsprecher mit der

      Frequenzweiche verkabeln (Paralell-Schaltung):

    Hinweis:  Bevor alle Tieftöner an die Frequenzweiche angeschlossen werden,  sollte die Polarität aller Tieftöner an einer 9 Volt-Batterie

    überprüft werden:

      Pol des FW-Eingang an von 9 V Batterie

      Pol des FW-Eingang an von 9 V Batterie

    Alle Tieft ö ner m ü ssen bei dieser Ü berpr ü fung gleichm äß ig ausschwingen! 

      Ein verpolter Tieft ö ner kann die gesamte Basswiedergabe   aufheben! 

      8. Frequenzweichenmontage und Lautsprecheranschluss 

      5.1.1 Frequenzweichen vorverkabeln - vgl. Abb. Seite 11.  5.2.1 Gehäuse entfernen und hinter dem Steg des Türpaneels zwischen  Türverkleidung und Türpaneel einschieben und sicheren Sitz

      befestigen.

      Tief- und Mitteltöner einsetzen und alle Lautsprecher mit der

      Frequenzweiche verkabeln (Paralell-Schaltung):

    Hinweis:  Bevor alle Tieftöner an die Frequenzweiche angeschlossen werden,  sollte die Polarität aller Tieftöner an einer 9 Volt-Batterie

    überprüft werden:

      Pol des FW-Eingang an von 9 V Batterie

      Pol des FW-Eingang an von 9 V Batterie

    Alle Tieft ö ner m ü ssen bei dieser Ü berpr ü fung gleichm äß ig ausschwingen! 

      Ein verpolter Tieft ö ner kann die gesamte Basswiedergabe   aufheben! 

      75151 - Audi A 4 Cabrio - 10 - © JEHNERT SOUND DESIGN

    ✚ ✚

    Nachdem alle Tieftöner an die Frequenzweiche angeschlossensind, sollte die Polarität aller Tieftöner an einer 9-Volt-Batterieüberprüft werden (an Weicheneingangskabel auf Endstufenseite).

      8. Crossover circuit - Speaker connection 

      8.1. precable crossovers - see fig. page 11.

      8.2. install crossover – without housing; covered with foamed material-  in the hollow space between in the door-lining above the two front woofers and

      the original tweeter mount – see fig.).  Check precise fit.

      8.3. Insert subwoofer and midrange and connect all loudspeakers  with the included standart cables for subwoofer to the crossover circuit:

      parallel wiring see diagram on page 11.

    Notice:  You should check the polarity of all subwoofers  before connecting them to the crossover circuit

      with a 9 volt battery:

      pole of the crossover circuit input to of a 9 Volt battery

      pole of the crossover circuit input to of a 9 Volt battery

    All subwoofers must move uniformly! 

    Wrong polarity of a subwoofer can totally 

      equalize the bass sound! 

      8. Crossover circuit - Speaker connection 

      8.1. precable crossovers - see fig. page 11.

      8.2. install crossover – without housing; covered with foamed material-  in the hollow space between in the door-lining above the two front woofers and

      the original tweeter mount – see fig.).  Check precise fit.

      8.3. Insert subwoofer and midrange and connect all loudspeakers  with the included standart cables for subwoofer to the crossover circuit:

      parallel wiring see diagram on page 11.

    Notice:  You should check the polarity of all subwoofers  before connecting them to the crossover circuit

      with a 9 volt battery:

      pole of the crossover circuit input to of a 9 Volt battery

      pole of the crossover circuit input to of a 9 Volt battery

    All subwoofers must move uniformly! 

    Wrong polarity of a subwoofer can totally 

      equalize the bass sound! 

     

    ✚ ✚

    You should check the polarity of all woofers after havingconnected them to the crossover circuit with a 9 volt battery(input cable on the side of the amplier

    install crossover – without housing, covered with foamed material –in the hollow space between doorboard and doorlining (see g.)and ensure precise t.

  • 8/18/2019 Jehnert 75151 EBA Engl Web

    12/16

  • 8/18/2019 Jehnert 75151 EBA Engl Web

    13/16

    Abnehmen der Abdeckblenden: 

    Die Abdeckblenden können durch vorsichtiges Lösen der Klettverschlüsse jederzeit abgenommen werden.

    VORSICHT: 

    Bitte jede Art von » gewaltsamem Reißen  « an den Blenden

      vermeiden (Bruchgefahr !)

      75151 - Audi A 4 Cabrio - 12 - © JEHNERT SOUND DESIGN

      Die Klettverschlüsse sind ab Werk bereits komplett auf den Abdeckblenden

      montiert.

    WICHTIG : 

      Die Klettverschl ü sse haften sehr stark! 

      Die Abdeckblenden deshalb erst nach kompletter Montage der T ü rpaneele 

      und Soundsystem fest aufdr ü cken ! 

      Tipp: 

      ... wenn sich die Abdeckblende an manchen Stellen nicht auf dem   Paneel festdr ü cken l äß t ...

      Ursache: Die besondere Formgebung der Türpaneele an dieser Stelle

      und die daraus resultierende unterschiedliche Materialstärken

      der Abdeckblenden.

    Lösung: Mit einer M 4-Unterlagscheibe ø 20mm (3) unter dem

      Klett-Teller wird dieser Abstand einfach und schnell ausgeglichen:

    9. Montage der Abdeckblenden : 

    Abdeckblende

    2 selbstklebendes Klettband

    1 Klett-Druckverschluss

    3 Unterlagscheibe M4 ø 20 als Distanzhilfe

    TürpaneelRemoving the grills: The Velcro fasteners stick together very strongly!The grills can be removed anytime by carefully lifting them off.Please, avoid any way of forceful yanking at the grills.

    It could break!

    9.3.

    9.2. Our Tip:   If the panel cannot be pressed on completely at some points. . .

      Cause: the special form at these points and the result ing differences inmaterial cross section of the grill.

      Solution: the distance can be levelled out with spacers 3 under theVelcro disc.

    (Spacers included with the screw kit)

      9.1. Precisely align and carefully press grill into the Velcro fasteners.

      The Velcro fastener makes a crackling sound   when it is closed correctly.

     

    9. Installation of the speaker ’  s grill: 

      grill

    2 self-adhesive Velcro-strip

    1 Velcro fastener

    3 Washer M4 ø 20 as spacer

    doorpanel

  • 8/18/2019 Jehnert 75151 EBA Engl Web

    14/16

      75151 - Audi A 4 Cabrio - 13 - © JEHNERT SOUND DESIGN

    T e c h n i s c h e I n f o r m a t i o n 

    Fahrzeugausstattung: elektrische Fensterheber

    Modell/ Modelljahr: A4 Cabrio

    Dämmung der Türen: empfohlen

    Einstell-Hinweis: Um den optimalen Raumklang zu erzielen,sollten am Radiogerät sämtliche Einstellungen

      (Bass, Höhen, Loudness usw.) auf Null bzw.  neutral eingestellt werden

    empfohleneVerstärkerleistung: ab 2x 200 - 360 Watt sinus / 4 Ohm

    Blechschneidearbeiten: entfallen

    Lautsprecherausschnitte/ 4 x 144mm (max.Außenmaß Tieftöner 165 mm)pro Seite (max.Einbautiefe Tieftöner 65 mm)

    Euro-Norm-Korb passend 

    1 x 92mm (max.Außenmaß Mitteltöner 100 mm)  (max.Einbautiefe Mitteltöner 55 mm)

    Sound-System: 3-Wege  4 x 160 mm Tieftöner / Seite

      1 x 100 mm Mitteltöner / Seite  1 x 26 mm Hochtöner / Seite

      fahrzeugspezifische Frequenzweiche  Belastbarkeit Dauer / Musik: 2 x 300/500Watt

    Übertragungsbereich: 49-22.000 Hz

      Impedanz: 4 Ohm

    Einbauzeit: Einbauprofi: 3-4 Stunden

    Änderungen, die dem technischen Fortschritt dienen, bleiben vorbehalten.

     

    T e c h n i c a l i n f o r m a t i o n  

    Equipment: electric window control

    Model/ year : coupé / roadster

    Insulation: Insulation not necessary

    Note about setting: To obtain optimal stereoscopic sound, all settingson the radio (bass, treble, loudness etc) should be

      set to zero or neutral.

    Recommendedamplifier power : from 2x 200 - 360 Watt RMS / 4 Ohm

    Metal cutwork : not necessary

    Cut-outs for loudspeaker/ 4 x 144mm (max.outer dimensions subwoofer 165 mm)each side (max.installation depth subwoofer 65 mm)

    DIN-Euro-Norm-standard basket ø 6“ -  panel modification necessary

      1 x 92mm (max.outer dimensions midrange 100 mm)  (max.installation depth midrange 60 mm)

    Sound-System: 3-ways  4 x 160 mm subwoofer/ side

      1 x 100 mm midrange / side  1 x 26 mm tweeter / side  car-customized crossover network

      max.continuous Watt/RMS: 2 x 300/500Watt  car specific frequency range: 49-22.000 Hz

      Total impedance: 4 Ohm

    Time for Installation car hifi-specialist: 3 hours

    We reserve the right to make technical changes, as well as development.

    55 mm)

    is recommended

    A4 Convertible

  • 8/18/2019 Jehnert 75151 EBA Engl Web

    15/16

    Steffen KretzschmarSattlerei / Produktionsablauf 

    Durchwahl: - 69

      75151 - Audi A 4 Cabrio - 14 - © JEHNERT SOUND DESIGN

    Technische Fragen: Info-Hotline: 0711 - 77 97 87 - 87 

    Wir danken f ür Ihre Unterstützung !

    Mirko SchwarzProduktentwicklung / Qualität

    Durchwahl: - 67

    Wir helfen Ihnen gerne weiter!

    Sehr geehrter Kunde,

    Wir haben uns sehr bemüht unsere neuen Montageanleitungen ausf ührlicher und“Schritt f ür Schritt” zu erklären.

    Ihre Tipps und Anregungen helfen uns künftige Unklarheiten oder Fehlinter-pretationen weiter auszuschließen.

    Teilen Sie uns deshalb mit, was Ihnen nicht gef ällt oder was wir noch ändern sollten.

    Marc SitterVersand / Service

    Durchwahl: - 68

    Marc SitterVersand / Service

    Durchwahl: - 68

    Die folgenden Hinweise sollen Ihnen dabei helfen, Fehler oder Störungen selbst zubeheben. Wenn folgende Abhilfemaßnahmen nicht greifen, rufen Sie uns bitte an:

    Was kann es sein ... mögliche Ursache / Lösung

    wenn’s nicht richtig klingt  Tieftöner verpolt ( Seite 10)

      Frequenzweichen falsch angeschlossen ( Seite 11)

      Türverkleidung und Regenschutzfolie  nicht ausgeschnitten ( Seite 7+9)

      Verstärker zu wenig Leistung ( Seite 13)

      Verstärker-Anschluss

    wenn’s nicht richtig passt  Fixpunkte Türpaneelanpassung ( Seite 6)

      Montage der Paneele auf die TV ( Seite 7)

    Abdeckungen nicht haften  Hinweise Seite 12 beachten!

    Vibrationsgeräusche  Dämmung s. Hinweise Seite 8

    Selbsthilfe und Fehlersuche

           

           

           

           

           

           

           

           

     

    Die folgenden Hinweise sollen Ihnen dabei helfen, Fehler oder Störungen selbst zubeheben. Wenn folgende Abhilfemaßnahmen nicht greifen, rufen Sie uns bitte an:

    Was kann es sein ... mögliche Ursache / Lösung

    wenn’s nicht richtig klingt  Tieftöner verpolt ( Seite 10)

      Frequenzweichen falsch angeschlossen ( Seite 11)

      Türverkleidung und Regenschutzfolie  nicht ausgeschnitten ( Seite 7+9)

      Verstärker zu wenig Leistung ( Seite 13)

      Verstärker-Anschluss

    wenn’s nicht richtig passt  Fixpunkte Türpaneelanpassung ( Seite 6)

      Montage der Paneele auf die TV ( Seite 7)

    Abdeckungen nicht haften  Hinweise Seite 12 beachten!

    Vibrationsgeräusche  Dämmung s. Hinweise Seite 8

    Selbsthilfe und Fehlersuche

           

           

           

           

           

           

           

           

    Technische Fragen: Info-Hotline 0 71 58 / 9 56 99-0Technical questions: Hotline 00 49 71 58 / 9 56 99-0

     

    The following notes serve to help troubleshoot and eliminate faults or malfunctionson your own. If the following measures are not effective, please call us.

    What can it be if ... possible cause/ solution

    ..it doesn’t sound right.   wrong polarity on the subwoofers ( page 10)  crosover circuit attached wrong ( page 11)

      Doorlining and moisture protection foil  not cut out ( page 5+10)

      amplifier doesn’t have enough power( page 13)

      amplifier connection

    ...it doesn’t fit correctly. door panel customization ( page 8)

      installation of the panels on the door lining (page 9)

    .....grills do not hold.  observe notes on page 12!

    vibrations   insulation, see notes on page 7

    Self-help and fault diagnosis

           

           

           

           

           

           

           

    6)

    7)

    8

    7 + 9) 

    It is our pleasure to help you!

     

  • 8/18/2019 Jehnert 75151 EBA Engl Web

    16/16

    G u a r a n t e e 

      2001/by.AJ/FH - 15 -

    We grant a manufacturers guarantee of 2 years starting from the date of purchaseof the door panels or sound system from the dealer.

    Within this guarantee period to our choice we either repair or replace free of charge all defects due to material or workmanship.

    Exempt from this guarantee are damages due to improper use, wear and tear ordamages which have to be led back on wear or interventions by third parties.The guarantee does not cover subsequent damages or such defects that onlyinsignificantly impair the value or the usability of the panels/sound system.The guarantee does not cover damages due to external influences.

      Panels with additional or wrong assembly drill holes cannot be returned.  These are damages to the panel which cannot be repaired again.