Upload
didik-rachmadi
View
642
Download
7
Embed Size (px)
Citation preview
LAPORAN PEMERIKSAAN RIG Rig : DRILLCO # 1, (2000 HP)
PENDAHULUAN :
Pemeriksaan kelengkapan rig dilaksanakan pada : Rig ID DRILLCO # 11Pemilik Rig Lokasi : Batu Ampar , Batam IslandTanggal Premeriksaan : 26 s/d28 Mei 2010
Maksud dan Tujuan ;Standar Inspeksi perlengkapan Rig dipersiapkan dengan maksud dan tujuan sebagai berikut :1. Sebagai standard baku dalam evaluasi kelengkapan perlengkapan Rig yang ditawarkan dalam dokumen lelang oleh peserta lelang.2. Sebagai standar baku dalam inspeksi perlengkapan Rig untuk menyesuaikan perlengkapan yang ditawarkan dalam dokumen penawaran dengan kondisi perlengkapan pada saat inspeksi
Rig DRILLCO # 1, dengan deskripsi sbb : Service / Type Drilling / Land Rig Classification / std manufacture Cantilever / API 4F Manufacture Tahun Pembuatan Height Mast (derrick) Mast serial number Static hook load capacity 1.000.000 lbs (545 ton) Rated Power 2.000 HP Substructure model IDECO – HFM-147-1000 Combined load capacity 1.600.000 lbs
1.0 GENERAL DESCRIPTION OF EQUIPMENT
1.1 MINIMUM REQUIREMENTS EBE :
Land Rig, SCR Type/Mechanical, New Rig / one (1) year used, Up to 16,000 ft with 5” DP, Give dates when available, Estimate time from award to ready to spud.
CONTRACTOR’S OFFER : Drillco-1, 2000 HP Land Rig with VFD and Top Drive, ZYZJ Petroleum Equipment Company, China , 2008 Built new rig , 20,000 Ft with 5” DP. Immediately Available, In Indonesia, 45 Days
1.2 Main Rig Features :
Main Rig FeaturesMINIMUM REQUIREMENTS
CONTRACTOR’S OFFER
Mast G.N.C. 1,000,000 lbs 1,000,000 lbs
Substructure G.N.C. 1,300,000 lbs 1,421,980 lbs
Drawworks power Min 2,000 H.P. 2000 HP
Rotary Table 37.5 inches 37.5 in
Mud Pumps3 X 1600 H.P. or equiv.
3 X 1600 HP
Rig Power System Electric SCR /MechanicalVariable Frequency Drive
(VFD)
BOP Equipment 29-1/2 inch, 500 psi Diverter Eqpt
29-1/2”, 500 psi Diverter system
21-1/4", 2,000 psi BOP's 20 ¾”, 3000 psi
13-5/8", 10,000 psi BOP's 13 5/8”, 10000 psi
Liquid Mud - Active/Reserve
Storage Capacity Min. 2700 bbls 2773 /2232 bbl
Drill Water Storage Capacity 1200 bbls 1006 bbl
Potable Water Storage Capacity 325 bbls 400 bbls
Diesel Fuel Storage Capacity 700 bbls 730 bbls
No. of Truck loads for all
equipment and camp 146
1.3 Transportation Equipment ( See Note )
1.4 Camp and Office Facilities (see Notes )
2.0 DETAILED DESCRIPTION OF EQUIPMENT
2.1 MAST
ITEM DESCRIPTION OF EQUIPMENT MINIMUM REQUIREMENTS CONTRACTOR’S OFFER
2.1 MAST
Make and Type Should be self-elevating, drawing required Yes
Clear Height 147 ft is preferred 149 Ft
Base Width 30 ft 32.8 Ft
Gross Nominal Capacity 1,100,000 lbs 1,010,000 lbs
Hook Load with 12 lines 880,000 lbs 1,010,000 lbs
Hook Load with 10 lines 841,666 lbs
Hook Load with 8 lines 673,333 lbs
Max. windload - No setback 100 mph 107 mph
Max. windload - With setback 84 mph 80.5 mph
Crown Block Capacity 500 ton 500 Ton
Number of sheaves 6 sheave cluster + fast line6 Sheaves +1 fast
line
Size of sheave grooves 1 - 3/8" 1 ½””
Racking Board Make, Type, and Capacity
For 14,400 ft 5” DP & 6-1/2” DC stands
ZYZJ, 17,000 Ft (5” DP, 6 ½” DC)
Number of Standpipes 1 Dual Stand Pipe, H
Type Manifold
Standpipe size 5" 5” OD, 4” ID
Standpipe Pressure Minimum 5000 psi 5000 psi
ITEM DESCRIPTION OF EQUIPMENT MINIMUM REQUIREMENTS CONTRACTOR’S OFFER
Rating
Number/Size of Standpipe valves 2 x 5"; 2 x 2" 2 X 5”, 2 X 2”
Pressure Rating of Standpipe valves 10,000 psi 10,000 psi
2.2 SUBSTRUCTURE
ITEM DESCRIPTION OF EQUIPMENT MINIMUM
REQUIREMENTS CONTRACTOR’S OFFER
2.2 SUBSTRUCTURE
Make and TypeShould be self-
elevating, drawing required
ZYZJ , DZ 450/10.5-S, Swing up Style, self elevating.
Floor Height 30 ft 34.5 Ft
Clear Height 23 ft 29.5 Ft
Length 45 ft 41.5 Ft
Width 37 ft 42.64 Ft
Gross Nominal Capacity 1,100,000 lbs 1,494,500 lbs
Casing Capacity 800,000 lbs 900,000 lbs
Simultaneous Setback Capacity 600,000 lbs 594,500 lbs
2.3 DRAW WORKS
ITEM DESCRIPTION OF EQUIPMENT MINIMUM
REQUIREMENTS CONTRACTOR’S OFFER
2.3 DRAW WORKS
Make and TypeACR/SCR/Electrical/
Mechanical JC 70DB/VFD AC Electric
Drawworks
Length overall 25 ft 29.44 Ft
Width overall 10 ft 9 inch 10 Ft
Weight 72,000 lbs 115,522 lbs
HP Rating 2,000 BHP 2000 BHP
Hoisting Drum Size 30" x 56" 30 3/8" X 56 3/4"
Brake Rim Size 54" x 10" 63” X 3” Disc Brake DBS-75
Number of Hoisting gears 4 Step less speed regulator
No/Make/Type/Rating of DC Traction Motors
2/ / /1000 BHP at 1000
rpm
2 / YJ13X5/6 / 800 KW at 741 rpm AC motors (VFD
controlled)
No/Make/Type of Catheads
2/ / / 3/China/Hydraulic Cathead
Make/Type of Electric Brake Eaton 436WCB
Electric Brake rating 95,000 ft-lb at 50 rpm 98,333 ft.lb
Sandline Drum size
12" x 50"
Independent slick line unit available for taking survey, however, if required, will
provide independent sand line unit for swabbing operations.
Sandline Drum Capacity
Independent Sandline, 16” OD
Amount/Size of sandline
23,000 ft x 1/2" dia. IWRC cable. 23,000’ x 5/16” Braided Wire
Brake Rim size 16” Brake Rim
2.4 DRILLING LINE
ITEM DESCRIPTION OF EQUIPMENT MINIMUM
REQUIREMENTS CONTRACTOR’S OFFER
2.4 DRILLING LINE
Make and Type /1-3/8"/6 x 19 IPS Cable IWRC 1 ½”/ 6 X 19S IWR API 9B
Length on drum 10,000 ft 10,000 Ft
2.5 ROTARY TABLE/TOP DRIVE (BOTH REQUIRED)
ITEM DESCRIPTION OF EQUIPMENT MINIMUM
REQUIREMENTS CONTRACTOR’S OFFER
2.5ROTARY TABLE/TOP DRIVE (BOTH REQUIRED)
Must be independently
driven and powered
capable of switching to top drive operation.
Make and Type of Rotary Table ZYZJ, ZP-375
Size/Minimum opening 37-1/2 inches 37 ½”
Static Load 500 tons 645 Ton
Maximum Torque 23.,870 Ft –lbs
Maximum speed 300 rpm
Number of Transmission speeds 2 Step less transmission
Make/Type/Rating of DC Traction Motor YJ 31D/720KW/AC Motor
AccessoriesMaster Bushing and 1,2 and 3 insert bowls. Yes as specified
Make and Type of Top Drive
Tesco / Varco TDS - 9S or equiv. BPM/TDS-500, DQ 70BSC
Hoist capacity 500 ton total, API-8C, PSL-1, SR-1 500T as per API -8C
350 ton topsub, 350 T top sub
Drilling capacity 273 ton API 273 ton API
Water course 5000 psi CWP 5000 psi CWP
Speed range 0-225 rpm cont. 0-220 rpm
Torque Max 32,500 ft. lb. 55,300 Ft-lb
Horse-Power 700 max. cont. 800 KW
Static Locking brake 35000 ft. lb. 36,900 Ft-lb
Electric Motors 2 x 350 HP 2 X 400 KW
2.6 TRAVELING BLOCK/HOOK
ITEM DESCRIPTION OF EQUIPMENT MINIMUM
REQUIREMENTS CONTRACTOR’S OFFER
2.6
TRAVELING BLOCK/HOOK
Make and Type ZYZJ, YC450
Capacity 400 tons 450 T
Number of sheaves 6 6
ITEM DESCRIPTION OF EQUIPMENT MINIMUM
REQUIREMENTS CONTRACTOR’S OFFER
Sheave Groove Size 1-3/8" 1 ½”
Hook Make and Type DG-450 to API 8A
Hook Capacity 400 tons 450 T
2.7 SWIVEL
ITEM DESCRIPTION OF EQUIPMENT MINIMUM
REQUIREMENTS CONTRACTOR’S OFFER
2.7 SWIVEL
Make and Type SL 450 to API 8A
Capacity 500 tons 450 T
Spare swivel 1 ea 1 ea
2.8 ROTARY HOSE
ITEM DESCRIPTION OF EQUIPMENT MINIMUM
REQUIREMENTS CONTRACTOR’S OFFER
2.8 ROTARY HOSE
Make and Type Made in China Rotary Hose
Size/Pressure Rating 3" ID/10,000 psi WP 3” ID/5000 psi WP
Length 75 ft 75 Ft
Other features Safety clamps & Yes
ITEM DESCRIPTION OF EQUIPMENT MINIMUM
REQUIREMENTS CONTRACTOR’S OFFER
chains
Spare 2 spare 2 spare
2.9 KELLIES
ITEM DESCRIPTION OF EQUIPMENT MINIMUM REQUIREMENTS CONTRACTOR’S OFFER
2.9 KELLIES
Large Drill Pipe String
Make and Type Made in China Hex
Kelly
Size 5-1/4" Hex 5 ¼” Hex
Length 40 Ft
Pressure rating 10,000 psi 10,000 psi
Make & Type of Kelly Bushing
Varco 27 HDP or equiv. China Pin Type
Make & Type of Saver Sub China 4-1/2” IF Box x
Pin
Make/Type/Press. Rating of Upper Kelly Cock
/ /10,000 psi
China 10,000 psi full open ball type
Make/Type/Press. Rating of Lower Kelly Cock
/ /10,000 psi
China 10,000 psi full open ball type
Spare 1 spare 2 spare
Small Drill Pipe String
Make and Type
Size 3-1/2" Hex 4-1/4” Hex
Length 40’
Pressure rating 10,000 psi 10,000 psi
ITEM DESCRIPTION OF EQUIPMENT MINIMUM REQUIREMENTS CONTRACTOR’S OFFER
Make & Type of Kelly Bushing
Varco 27 HDP or equiv. China Pin Type
Make & Type of Saver Sub China 3-1/2” IF Box x
Pin
Make/Type/Press. Rating of Upper Kelly Cock
/ /10,000 psi
China 10,000 psi full open ball type
Make/Type/Press. Rating of Lower Kelly Cock
/ /10,000 psi
China 10,000 psi full open ball type
Spare 1 spare 2 spare
2.10 KELLY SPINNER
ITEM DESCRIPTION OF EQUIPMENT MINIMUM REQUIREMENTS CONTRACTOR’S OFFER
2.10 KELLY SPINNER
Make and Type Varco Model 6600 or equiv. Integrated with Swivel
Maximum Torque Stall torque 1200 ft-lbs
Quantity 1
2.11 BOP EQUIPMENT
ITEM DESCRIPTION OF EQUIPMENT MINIMUM REQUIREMENTS CONTRACTOR’S OFFER
2.11 BOP EQUIPMENTA complete set of
stackup drawings should be provided, with all dimensions marked.
Complete with BOP Stack drawing
a Diverter Equipment
Make/Type/Size/Press. rating of Annular 29-1/2", 500 psi
Annular BOP/29-1/2”/500 psi
Make/Type/Size/Press. rating of Div. Spool 29-1/2", 500 psi
Diverter spool/29-1/2”/500 psi
Size/Press. rating/Conn. of side-outlets
10"; 12" preferred/ANSI 900 or ANSI 600
10”/ANSI Class 600
Make/Type/Size/Press. rating of valves
10"; 12" preferred/ ANSI 900 or ANSI 600
Ball valve/10”/ANSI Class 600
Control System for valves
Air or hydraulic. Should be linked to annular for automatic operation
Hydraulic control system
No/Length/Size/Conn of Diverter Lines
10"; 12" preferred. 240 ft with flange connections
240’/10”/Flange type conn
b Low Pressure BOP
Make/Type/Size/Press. rating of Annular 21-1/4", 2,000 psi
Rongsheng, 20-3/4", 3,000 psi
Make/Type/Size/Press. rating of Upper rams 21-1/4", 2,000 psi
Rongsheng, Double ram BOP
20-3/4", 3,000 psi
Make/Type/Size/Press. rating of Lower rams 21-1/4", 2,000 psi
Rongsheng, Double ram BOP
20-3/4", 3,000 psi
Number of sets of blind and/orshear
1 set 1 set
ITEM DESCRIPTION OF EQUIPMENT MINIMUM REQUIREMENTS CONTRACTOR’S OFFER
rams
Number of sets and sizes of pipe rams 1 set 5" pipe rams 2 set 5" pipe rams
1 set 13-3/8" casing rams1 set 13-3/8" casing
rams
Number and sizes of Kill Line inlets 3,000 psi 10,000 psi
Number and sizes of Choke Line outlets 3,000 psi 10,000 psi
Kill Line valves 3,000 psi 10,000 psi
Choke Line valves 3,000 psi 10,000 psi
HCR Actuated Valves 3,000 psi 10,000 psi
Mud Cross To conform to above20-3/4”, 3000 psi
with 4-1/16”, 5000 psi Outlet
Adaptor Spools Bidders to list all available types
21-1/4" 2000 psi X 20-3/4" 3,000 psi
4 1/16" 5000 psi X 4 1/16" 10,000 psi
Spacer Spools Bidders to list all available spools 9 Meter Spacer spool
c High Pressure BOP
To be trimmed to H2S sour service. All rubber
goods and annular elements to be new and
suitable for service
Make/Type/Size/Press of Annular 13-5/8", 10,000 psi
Rongsheng/13-5/8, 5,000 psi
Make/Type/Size/Press of Upper rams
13-5/8", 10,000 psi Rongsheng/Double/13-5/8”, 10,000 psi
Make/Type/Size/Press of Upper
13-5/8", 10,000 psi
ITEM DESCRIPTION OF EQUIPMENT MINIMUM REQUIREMENTS CONTRACTOR’S OFFER
Middle rams
Make/Type/Size/Press of Lower Middle rams 13-5/8", 10,000 psi Not Available
Make/Type/Size/Press of Lower rams 13-5/8", 10,000 psi
Rongsheng/Single/13-5/8”, 10,000 psi
Number of sets of blind and/orshear rams 1 set blind, 1 set shear
2 Set Shear-Blind Ram for 5” DP
Number of sets and sizes of pipe rams 1 set 3-1/2" pipe rams 2 set 3-1/2" pipe rams
1 set 5-1/2" casing rams2 set 5-1/2" casing
rams
2 sets 5" pipe rams 4 Sets 5” Pipe rams
1 set 7" casing rams 2 set 7" casing rams
1 set 9-5/8" casing rams2 set 9-5/8" casing
rams
VBR rams 2 sets 4-1/2" - 9-5/8" Not Available
Number and sizes of Kill Line inlets 10,000 psi 1, 4 1/16”, 10,000 psi
Number and sizes of Choke Line outlets 10,000 psi 1, 4 1/16”, 10,000 psi
Kill Line valves 10,000 psi Yes, 10,000 psi
Choke Line valves 10,000 psi Yes, 10,000 psi
Mud Cross To conform to above 13-5/8”, 10,000 psi
Adaptor Spools Bidders to list all available types Yes, as specified
Sufficient to install BOPs on all Company supplied
wellhead Sections
all Sufficient DSAF available for installation
of company supplied well head sections
Spacer Spools Bidders to list all available spools
2, 13 5/8”, 10,000 psi, length 0.8m to 1.5 m
ITEM DESCRIPTION OF EQUIPMENT MINIMUM REQUIREMENTS CONTRACTOR’S OFFER
20 ¾”, length 0.8m to 1.5m
d Kill and Choke Lines
To conform to BOP requirements
Type/Size/Press. rating of Kill Line
2", 10,000 psi Colflexip hose, H2S service
3-1/16” x 10,000 psi H2S Services
Type/Size/Press.rating of check-valve 1 ea, 2-1/16" x 10,000 psi
1 ea, 3-1/16” x 10,000 psi
Type/Size/Press. rating of Choke Line 3-1/16” x 10,000 psi
e Choke Manifold YG/Y103-78/70
Size and Pressure rating
3-1/16", 10,000 psi, sour service
4 1/16”, 10,000 psi, Sour service
No/Size/Press. rating/Make/Type Man. Choke 1 ea - 3-1/16", 10,000 psi
Yes, 4 1/16”, 10,000 psi
No/Size/Press. rating/Make/Type Adj. Choke 1 ea, 3-1/16", 10,000 psi 4-1/16” x 10,000 psi
Size/Press. Rating/Make/Type/Hydraulic Choke 2 ea , 3-1/16", 10,000 psi
Yes, 4 1/16”, 10,000 psi
Make/Type of Choke Control Panel Swaco or equiv./hydraulic Equivalent
No/Size/Press. rating/Make/Type valves
Diagram to be provided 10 ea, 3-1/16", 10,000 psi
flanged gate-valves 10 ea, 4-1/16”, 10,000 psi flanged gate valves
No/Press. rating/Make/Type Pressure gauges
1 on manifold, 1 on Control Panel
2 ea/10,000 psi/Placed on Manifold and Control
Panel
No/Press. rating/Make/Type
2 2 ea/10,000 psi
ITEM DESCRIPTION OF EQUIPMENT MINIMUM REQUIREMENTS CONTRACTOR’S OFFER
Press. Transmitters
f Accumulator Unit In skid-mounted building Skid Mounted
Make and Type Suitable for BOP requirements
FKQ1280-7, Dongsu Machinery
manufacturing co.ltd
Capacity of reservoir tank
Suitable Volume to meet API requirements 200 Gallons
No/Size of Accumulator Bottles
Required API Number and Volume
20 Bottles, 11 Gallons each
Master Control Set 7 stations. 8 stations
No/Type of pressure gauges Analog Pressure Gauge
No/Make/Type of air driven charge pumps 3 ea/ /
2, Dongsu Machinery manufacturing co.ltd,
Pneumatic
No/Make/Type of electric driven charge pumps 2 ea/ /15 HP
1, Dongsu Machinery manufacturing co.ltd,
Electric
No/Type of Remote Control Stations 1 ea/
2 stations, 1) Drill floor, 2) Tool pusher’s office
No/Type/Length of control hoses 150 ft 150 ft
No/Size of control line suitcases 3 ea x 30 ft long. 3 ea x 30 ft long
Alarm System Alarm System
Emergency Air Compressor 2 ea, Driven by 2 cyl
diesels
Compressor lined up with battery operated
engine
2.12. MISCELLANEOUS WELL CONTROL EQPT
ITEM DESCRIPTION OF EQUIPMENT MINIMUM REQUIREMENTS CONTRACTOR’S OFFER
2.12MISCELLANEOUS WELL CONTROL EQPT
a Inside BOP
Make & Type China, Float Type
No/Size/Conns 1 ea for 5" & 3-1/2" DP2 Ea for 4 ½” & 3 ½”
DP
Working Pressure 10,000 psi 10,000 psi
B Drop In Subs 2 ea for 5" DP & 3-1/2 DP 2 ea for 5” DP & 3-
1/2” DP
Working Pressure 10,000 psi 10,000 psi
Requirements:
Wireline retrievable Capable of passing through full open
kelly cocksWireline retrievable
C Stabbing Valves
ITEM DESCRIPTION OF EQUIPMENT MINIMUM REQUIREMENTS CONTRACTOR’S OFFER
Make & Type Full opening Full opening
No/Size/Conns3 ea for 5" & 3-1/2" DP
3 ea for 5” & 3-1/2” DP one for sour
services
Working Pressure 10,000 psi 10,000 psi
D Flare Line
Length 300 ft 300’
Size 3-1/2”
Pressure rating 5,000 psi
Connections 3-1/2” EUE
e Casing Cup Testers 1 ea 13-3/8" Cameron 'F' 1, 13-3/8”, China
1 ea 9-7/8" Cameron 'F' 1, 9-7/8”, China
1 ea 9-5/8" Cameron 'F' 1, 9-5/8”, China
1 ea 7" Cameron 'F' 1, 7”, China
2.13 MUD PUMPS
ITEM DESCRIPTION OF EQUIPMENT MINIMUM REQUIREMENTS CONTRACTOR’S OFFER
2.13 MUD PUMPSAll mud pumps to be
equipped
for service.
Combined output –
1300 gpm @ 2500 psi
a Pump No 1 ZYZS Model ZY1-
1600
Make and Type Triplex only Triplex
Rated HP 1600 HP 1600 HP
Maximum Working 5000 psi 5000 psi
ITEM DESCRIPTION OF EQUIPMENT MINIMUM REQUIREMENTS CONTRACTOR’S OFFER
Pressure
Maximum SPM 120 SPM
Stroke Length 12”
Liner sizes available Bidders to list stock to be supplied 7”, 6-1/2”, and 6”
Suction manifold 1 ea 1 ea
Spare Suction and discharge modules 1 of each 1 ea
No/Type/Rating of DC Traction motors
2 ea/ /1,300 HP at 1000 rpm
2 ea /AC VFD Motors/ 720KW
Make/Type/Press of Pulsation Dampener Hydril/K-20/5000 psi K-20, 5,000 psi
Make/Type of Suction Damper Suction Strainer
Make/Type/Size of Centrifugal charge pump
/ /5" x 6"
China / Centrifugal 5” x 6”
Make/Type/Size of charge pump electric motor
/ /60 HP
Electric Motor 60 HP
Length/Size/WP of Vibrator Hose 12 ft/ 4" /5000 psi WP
14.5’ / 4” / 5,000 psi
b Pump No 2
Make and Type Triplex only Triplex
Rated HP 1600 HP 1600 HP
Maximum Working Pressure 5000 psi 5000 psi
Maximum SPM 120 spm
Stroke Length 12”
Liner sizes available Bidders to list stock to be 7”,6-1/2”, and 6”
ITEM DESCRIPTION OF EQUIPMENT MINIMUM REQUIREMENTS CONTRACTOR’S OFFER
supplied
Suction Manifold 1 ea 1 ea
Spare suction and discharge modules 1 of each 1 ea
No/Type/Rating of DC Traction motors
2 ea/ /1,300 HP at 1000 rpm
2 ea /AC VFD Motors/ 720KW
Make/Type/Press of Pulsation Dampener Hydril/K-20/5000 psi K-20, 5000 psi
Make/Type of Suction Damper Suction Stal rainer
Make/Type/Size of Centrifugal charge pump
/ /5" x 6"
China / Centrifugal 5” x 6”
Make/Type/Size of charge pump electric motor
/ /60 HP
Electric Motor 60 HP
Length/Size/WP of Vibrator Hose 12 ft/ 4" /5000 psi WP
14.5’ / 4” / 5,000 psi
c Pump No 3
Make and Type Triplex only Triplex
Rated HP 1600 HP 1600 HP
Maximum Working Pressure 5000 psi 5000 psi
Maximum SPM 120 SPM
Stroke Length 12”
Liner sizes available Bidders to list stock to be supplied 7”, 6-1/2”, and 6”
Suction Manifold 1 ea 1 ea
Spare suction and discharge modules 1 of each 1 ea
No/Type/Rating of DC Traction motors
2 ea/ /1,300 HP at 100 rpm
2 ea /AC VFD Motors/ 720KW
ITEM DESCRIPTION OF EQUIPMENT MINIMUM REQUIREMENTS CONTRACTOR’S OFFER
Make/Type/Press of Pulsation Dampener Hydril/K-20/5000 psi K-20, 5,000 psi
Make/Type of Suction Damper Suction Strainer
Make/Type/Size of Centrifugal charge pump
/ /5" x 6"
China / Centrifugal 5” x 6”
Make/Type/Size of charge pump electric motor
/ /60 HP
Electric Motor 60 HP
Length/Size/WP of Vibrator Hose 12 ft/ 4" /5000 psi WP
14.5’ / 4” / 5,000 psi
d Pump No 4
Make and Type Triplex only
Rated HP 1300 HP
Maximum Working Pressure 5000 psi
Maximum SPM
Stroke Length
Liner sizes available Bidders to list stock to be supplied
Suction Manifold 1 ea
Spare suction and discharge modules 1 of each
No/Type/Rating of DC Traction motors
2 ea/ /1,300 HP at 100 rpm
Make/Type/Press of Pulsation Dampener Hydril/K-20/5000 psi
Make/Type of Suction Damper
Make/Type/Size of Centrifugal charge pump / /5" x 6"
ITEM DESCRIPTION OF EQUIPMENT MINIMUM REQUIREMENTS CONTRACTOR’S OFFER
Make/Type/Size of charge pump electric motor
/ /60 HP
Length/Size/WP of Vibrator Hose
12 ft/ 4" /5000 psi WP
2.14 MUD TANKS
ITEM DESCRIPTION OF EQUIPMENT MINIMUM REQUIREMENTS CONTRACTOR’S OFFER
2.14 MUD TANKS All mud tanks to have roofs
and be suitable for oil
base and water base fluids. All
equipment to be suitable for
All mud tanks have roofs and suitable for oil base and
water base fluids. All equipment suitable for high temperature service. Tanks are equipped with agitators suitable for use with 18.0
ppg mud
ITEM DESCRIPTION OF EQUIPMENT MINIMUM REQUIREMENTS CONTRACTOR’S OFFER
high temperature
service. Tanks are to be
equipped with agitators
suitable for use with 18.0
ppg mud
a Degassing and Solids Control Tank(s)
Drawing(s) to be provided Drawings provided
Number of tanks required 1 1
LengthTank(s) to have
sufficient capacity 10.6 m
Width and be properly designed for 3.3 m
Heightefficient
degassing and solids control. 3.2 m
Capacity ± 330 bbls 340 bbls
No. of compartments 6 6
Equipment installed Shale Shakers and Sand Trap 1
Mud Laboratory 1
Degassing and solids control
pits 1 Ea
Drilling Degasser Vacuum Degasser/HZCQ-240
Mud Coolers
Portable Mud Cooler/Water and Air Cooling system/500
GPM
Desander, Desilter
Integrated with Derrick Mud Cleaner
Mud Cleaner(s)Mud Cleaner/Derrick FLC
2000
Charging pumps, 2 unit Charging pumps, suction
ITEM DESCRIPTION OF EQUIPMENT MINIMUM REQUIREMENTS CONTRACTOR’S OFFER
suction & &
discharge & transfer lines discharge & transfer lines
Dump and
equalization valves Dump and equalization valves
Mud trough, utilities Mud trough, utilities
Stairs, walkways, handrails etc. Stairs, walkways, handrails etc.
bMixing, Storage, and Suction Tank(s)
Drawing(s) to be provided Drawings provided
Number of tanks 3 3
Length
Active system (a & b) to have a min. cap. of
1500 bbls and be properly
designed for well circulation and the isolation,
mixing, transfer and storage of different fluids.
Active volume of a & b is 2232.88 bbl, length - 10.6 m
Width 3.3 m
Height 3.2 m
Capacity 350 bbls
No. of compartments 1
Equipment installed Agitators, Mudguns,
pumps, Mixing hoppers, mixing
and transfer lines, Mud
Trough Dump and equalization valves Utilities (power, water
and diesel lines), Stairs, walkways,
Yes, as specified
ITEM DESCRIPTION OF EQUIPMENT MINIMUM REQUIREMENTS CONTRACTOR’S OFFER
handrails etc.
c Reserve Mud Tanks Drawing(s) to be provided Drawings provided
Number of tanks 3 3
Length Reserve system to have a min. 10.6 m
Width cap. of 1200 bbls and be properly 3.3 m
Height designed for the isolation, mixing, 3.2 m
Capacitytransfer and storage of different 3 X 350 bbls
No. of compartments fluids
Equipment installed
Agitators, Mudguns,
pumps, Mixing hoppers, mixing
and transfer lines, Mud
Trough Dump and equalization valves Utilities (power, water
and diesel lines) Stairs, walkways,
handrails etc. Yes, as specified
Agitators
Suitable for use with 18.0 ppg drilling mud
Agitators to be capable of being
electrically isolated in SCR
room 15 nos
Dump LineTo come off
flowline direct to waste pit Yes
d Trip Tank Drawing to be provided Drawings provided
Length Trip tank is to be Independent Trip Tank
ITEM DESCRIPTION OF EQUIPMENT MINIMUM REQUIREMENTS CONTRACTOR’S OFFER
stand alone, not part of an active
tank
Width 3,3 M
Height 3,2 M
Capacity
± 40 bbl with dimensions such
that tank indicates clearly
small volume changes 60 bbls
2.15 SOLIDS CONTROL SYSTEM
ITEM DESCRIPTION OF EQUIPMENT MINIMUM REQUIREMENTS CONTRACTOR’S OFFER
2.15 SOLIDS CONTROL SYSTEM
A very good solids control system is
required. This will be a high priority for the
Third Party Rig Inspector. All eqpt to be
fit for service
All equipment fit for services
A Shale Shakers
Number/Make/Type The main shakers must be Linear Motion Type
3 / Flo-Line cleaner 2000-3 panel
(Derrick)/ Linear Motion type
Arrangement The preference is for at least 3 Linear Motion
3 Linear motion Shaker
Shakers in parallel Parallel position
Drawing to be provided Drawing provided
Specifications Bidders to specify for each Shale Shaker:
Derrik Flo-line2000-3 panel Shale shaker
ITEM DESCRIPTION OF EQUIPMENT MINIMUM REQUIREMENTS CONTRACTOR’S OFFER
Dimensions 2m X 1.1m X 1.7m
Weight 3450 Kg
Screen Area PMD Pyramid Screens
Drive Power 2.5 HP
G Force / Adjustable or not?Adjustable 2 Super G
vibrating motor
Drive Angle / Adjustable or not? Adjustable
Deck Angle / Adjustable or not? Adjustable
Screen sizes to be made available
A range of screen sizes from 20 mesh to 220 mesh
should be available.Sizes up to 250 mesh
screens
Bidders to list stock
B Desander(s)
Number 1 ea 1 Ea
Make and Type
Flo-Line cleaner 2000-3 panel
(Derrick)
Capacity 1200 gpm at 80 ft of head 1500 GPM max
Number/Size of cones 3 / 10” cones
Centrifugal Pump/Impeller size 6" x 8" 6” x 8”
Electric Motor size 75 HP 75 HP
C Desilter(s)
Number 2 ea 1 Ea
Make and Type
Flo-Line cleaner 2000-3 panel
(Derrick)
Capacity 2 x 400 gpm 1280 GPM Max
Number/Size of cones Specify 16 / 4” cones
Centrifugal 6" x 8"/ 6” x 8”
ITEM DESCRIPTION OF EQUIPMENT MINIMUM REQUIREMENTS CONTRACTOR’S OFFER
Pump/Impeller size
Electric Motor size 75 HP 75 HP
d Mudcleaner(s)
Number 1 ea 1 Ea
Make and Type Derrick/ Vibrating
Capacity 1280 GPM
Number/Size of cones 12/ 4” x 16
Centrifugal Pump/Impeller size 6" x 8"/ 6” x 8”
Electric Motor size 75 HP 75 HP
Screen sizes to be made available 100 - 250 mesh 100 Mesh 250
e Centrifuge(s)
2 ea suitable centrifuge installation are
required. This will consist of a high speed
unit and a barite recovery unit.
Contractor to provide this equipment. Contractor must
undertake to make necessary modifications
to install the equipment.
Number 1 Ea (Low speed & high speed)
Make and TypeLW500x1000-N,
LWG450x1260-N, China
SpecificationsMotor power 37 K, Drum speed 1700 rpm for LS, 2000-
3000 for HS
2.16 DEGASSING & COOLING SYSTEM
ITEM DESCRIPTION OF EQUIPMENT MINIMUM REQUIREMENTS CONTRACTOR’S OFFER
2.16 DEGASSING & COOLING SYSTEM
All eqpt to be suitable for high
All equipment suitable
temperature service.
for high temperature
service
a Poor Boy Mud Gas Separator
Contractor must demonstrate 'fit for purpose' design.
Yes, as specified
Drawing required Drawing provided
Diameter 48" 48”
Minimum Mud Seal 15 ft 15 Ft
Material steel steel
Working Pressure 50 psi 230 Psi
Pressure gaugePress. gauge to be provided for view by choke operator Yes, as specified
Location
Certification Yes, Certified
ITEM DESCRIPTION OF EQUIPMENT MINIMUM REQUIREMENTS CONTRACTOR’S OFFER
b Drilling Degasser
Make/Type
HZCQ240, Vacuum Degasser
Power Source Motor Power 15 KW
SpecificationsBidder to supply complete
set of
specifications
280-350 mmHg vacuum, 2.23 KW
vacuum motor power
c Mud Cooler
Contractor to supply. Contractor must undertake
to make necessary modifications to install the
equipment
Portable Mud Cooler/Water and Air Cooling system/500
GPM
2.17 ELECTRICAL SYSTEM
ITEM DESCRIPTION OF EQUIPMENT MINIMUM REQUIREMENTS CONTRACTOR’S OFFER
2.17ELECTRICAL SYSTEM
aMain AC Generators
maximum load on top drive, maximum mud
pump power and lifting off bottom
No/Make/Type 4 / Mitsubishi / MOG
ITEM DESCRIPTION OF EQUIPMENT MINIMUM REQUIREMENTS CONTRACTOR’S OFFER
1200
Rating - KW / RPM / V / Hz / Phases
1040 KW / 1500 rpm / 600V / 50 Hz / 3
Phase
Safety EquipmentComplete with safety
equipment
bDiesel Engine Units for AC Generators
Must provide sufficient power for the
anticipated Scope of Work.
No/Make/Type2 / SV-400GF / VOLVO
TAD1641GE
Rating - HP / BHP / RPM 536 HP / 1500 rpm
Safety Equipment Safety Shut Down Switches, Yes, as specified
Flame arrestor mufflers, air
start Battery Start
c SCR Unit
Rig fitted with Variable Frequency
Drive (VFD)
Make/Type
Siemens / AC-VFD-PLC
No. of AC feeders 4 4
No/Rating of SCR Converters 5/2000 Amps Not Required
No. of AC transformers 2
2 Main Transformer (in built)
ITEM DESCRIPTION OF EQUIPMENT MINIMUM REQUIREMENTS CONTRACTOR’S OFFER
Location Independent, temperature Independent VFD Unit
controlled, skid-mounted
facilitySkid mounthed can
run
capable of running three (3) mud pumps together
3 Mud Pump Together , 1040 KW, 1500 rpm,
600 V
d Prime Movers VFD
No/Make/Type of DC Traction Motors
9 set AC Drilling Motor, rated power 800 kW / 741 RPM, rate torque 10,303 Nm, 2ea for 3 mud
pumps, 2 ea for drawworks and 1 for
rotary table.
eEmergency AC Generator(s)
No/Make/Type
1/ C15 / Caterpillar / Emergency
Rating - KW / RPM / V / Hz / Phases
320 KW / 1500 rpm / 400 V / 50 Hz / 3
Phase
Safety Equipment
Complete with safety equipment
fDiesel Engine Unit for Emergency Gen.
No/Make/Type 1/ C15 / Caterpillar
ITEM DESCRIPTION OF EQUIPMENT MINIMUM REQUIREMENTS CONTRACTOR’S OFFER
Rating - HP / BHP / RPM 500 HP/ 1500 RPM
Safety Equipment
Safety Equipment Installed
gUPS / Battery Emergency Power System
Above engine is battery start
Make/Type
Rating
Usage
h Rig Lighting
Make/Type of main Explosion Proof Lights
The Rig is equipped with 220 V lighting
system at all specified locations
Numbers/locations Mast
Rig floor Rig floor
Substructure Substructure
Accumulator Unit Accumulator Unit
Choke Manifold Choke Manifold
Mud Pump Area Mud Pump Area
Solids Control System Solids Control System
Active Mud System Active Mud System
ITEM DESCRIPTION OF EQUIPMENT MINIMUM REQUIREMENTS CONTRACTOR’S OFFER
Reserve Mud System Reserve Mud System
AC Generator House AC Generator House
SCR House VFD House
Rig Utilities House Rig Utilities House
Fuel and Water Tanks Fuel and Water Tanks
Catwalk/Pipe racks Catwalk/Pipe racks
Movable units Movable units
Other – Detail
Around the rig site area
Make/Type of Emergency Lights (UPS / Batt)
China/Emergency light
Numbers/Locations - Detail
Emergency lights available at various
locations
2.18 COMPRESSED AIR SYSTEM
ITEM DESCRIPTION OF EQUIPMENT MINIMUM REQUIREMENTS CONTRACTOR’S OFFER
2.18COMPRESSED AIR SYSTEM
No/Make/Type of Air Compressors
2 x LS-12-50-HH / Screw Compressor
Capacity/W.P. 197.8 CFM / 155 psi
Make/Type/Rating of Prime Movers
Sular/ 50 HP, 380 volt, 50 Hz TEFC motors, air cooled oil and
after cooler
No/Make/Type of Air Dryers 1 / SCR-240 / 145 psi / 212 CFM
Location of compressed air outlets
Compressor House/ connected with battery operated engine
2.19 FUEL SYSTEM (See Notes)
2.20 WATER SYSTEM (See Notes)
2.21 LIFTING FACILITIES
ITEM DESCRIPTION OF EQUIPMENT MINIMUM REQUIREMENTS CONTRACTOR’S OFFER
2.21 LIFTING FACILITIES
aBOP Handling Equipment
Make/Type of BOP Hoists
2 Ea/ China / FY-40Y (combined capacity 40 T)
ITEM DESCRIPTION OF EQUIPMENT MINIMUM REQUIREMENTS CONTRACTOR’S OFFER
Make/Type of BOP Cradles
Integrated part of substructure
b Air Hoists
No/Make/Type/Capacity of Rig floor Air Hoists
2 / China / XJFH-5/35 / 11250 lb
No/Make/Type/Capacity of Catwalk Air Hoists 1 / China / same as above
No/Make/Type/Capacity of other Air Hoists
1/ china/ QJL-0,5X12 Rated speed 12M/ min
c Slings
Sufficient sets of certified slings for use during rigging
up/down and general material
handling operations.
Sufficient sets of certified slings for use during rigging
up/down and general material handling operations
No/Size/Length/Rating
Equipped with all size & capacity of sling for rigging up/ down and lifting general
material
List and describe
2.22 PIPE/TOOL HANDLING FACILITIES
ITEM DESCRIPTION OF EQUIPMENT CONTRACTOR’S OFFER
2.22PIPE/TOOL HANDLING FACILITIES
a Ramp V door ramp, 2m wide
Length 11.2M
Width 2M
Weight 1.1T
b Catwalk 1, 2 sections, 2 m wide
Length 13M
Width 2M
Height 1M
Weight 1.3T
c Pipe Racks
Number and Type 10 ea, triangle type 16 ea / triangle type
d Sub Racks
ITEM DESCRIPTION OF EQUIPMENT CONTRACTOR’S OFFER
Number and Type
e Tool Boxes
Number and Type
All tool boxes for all equipments and for general
tools available
2.23 REPAIR/MAINTENANCE FACILITIES (See Notes)
2.24 MISCELLANEOUS RIG EQUIPMENT (See Notes)
2.25 INSTRUMENTATION
ITEM DESCRIPTION OF EQUIPMENT MINIMUM REQUIREMENTS CONTRACTOR’S OFFER
2.25INSTRUMENTATION
aDriller's Console Display
Make/Type of Weight Indicator
Yes, China / Digital type
Make/Type of Rotary RPM meter
Yes, China / Digital type
Make/Type of Rotary Torque meter
Yes, China / Digital type
Make/Type of Top Drive Torque
Yes, China / Digital type
Make/Type of Top Drive RPM indicator
Yes, China / Digital type
ITEM DESCRIPTION OF EQUIPMENT MINIMUM REQUIREMENTS CONTRACTOR’S OFFER
Make/Type of Pump Pressure indicator
Yes, China / Digital type
Make/Type of Pump Stroke counter
Yes, China / Digital type
Make/Type of Pump Stroke totaliser
Yes, China / Digital type
Make/Type of Pit Level indicator
Yes, China / Digital type
Make/Type of Mud Flow indicator
Yes, China / Digital type
Make/Type of Tong Torque indicator
Yes, China / Digital type
bDrilling Operations Recorder
Digital Recording System
Make/Type
Yes, China / SZJ type
Location Driller’s console
Drilling Parameters recorder Hook Load Hook Load
Rotary RPM Rotary RPM
Rotary Torque Rotary Torque
Pump Pressure Pump Pressure
Pump Stroke Counters
Pump Stroke Counters
Top Drive Torque Top Drive Torque
ITEM DESCRIPTION OF EQUIPMENT MINIMUM REQUIREMENTS CONTRACTOR’S OFFER
Top Drive RPM Top Drive RPM
cDirectional Survey Equipment
No/Make/Type of Recorders
1 complete set of Totco Equipment
1 / Electronic / LHE3000
No/Make/Type of Angle units
1 / Electronic / LHE3000
No/Make/Type of Clocks Electronic
No/Make/Type of Survey Barrels Battery operated
No/Make/Type of Overshots
Wireline retrievable
No/Make/Type of Chart Reader Digital
Tool Box Yes, as specified
Make/Type of Measuring Line Unit
Model / CJ6000(F)/ Hydraulic
Size/Amount/Strength of line
2.5mm / 1 / 4077 KN
Prime Mover 7,5 KW
d Miscellaneous
DescribeAll pumps, compressors,
engines, Yes, as specified
generators, solids control
equipt,
ITEM DESCRIPTION OF EQUIPMENT MINIMUM REQUIREMENTS CONTRACTOR’S OFFER
degassing equipt, and other
machines should have their
own
instruments as per
manufacturers
recommendations and as
required for safe operation
eSpecial Requirement
2 ea Digital Pressure Gauges for Well
2 ea Digital Pressure 10,000
psi
Control Purposes (0,-10,000
psi)
2.26 DRILL STRING(S)
ITEM DESCRIPTION OF EQUIPMENT MINIMUM REQUIREMENTS CONTRACTOR’S OFFER
2.26 DRILL STRING(S)
a Drill Pipe 1
Length 14,228 ft 14,228 ft
Pipe Body O.D. 5 inch 5”
Range 2 Range 2
Weight 19.5 ppf 19.5 ppf
Class S-135 S-135
Connection 4-1/2" IF 4-1/2 IF
Tool Joint O.D.
Type of Hardbanding Smooth, fine Yes, as specified
Type of Internal Coating None Plastic coating
ConditionNew or premium with
thread protectorsBrand New c/w
Thread protectors
Date of last inspection
API Minimum requirements Brand New
ITEM DESCRIPTION OF EQUIPMENT MINIMUM REQUIREMENTS CONTRACTOR’S OFFER
b Drill Pipe 2
Length 5,000 ft 5,000 ft
Pipe Body O.D. 3-1/2 inch 3-1/2”
Range 2 Range 2
Weight 13.3 ppf 13.3 ppf
Class S-135 S-135
Connection 3-1/2" IF 3-1/2” IF
Tool Joint O.D.
Type of Hardbanding Smooth, fine Yes, as specifed
Type of Internal Coating None Plastic coating
ConditionNew or premium with
thread protectors Brand New
Date of last inspection Brand New
c Drill Pipe 3
Length 16,000 ft
Pipe Body O.D. 5”
Range Range 2
Weight 19.5 ppf
Class G-105
Connection 4-1/2 IF
ITEM DESCRIPTION OF EQUIPMENT MINIMUM REQUIREMENTS CONTRACTOR’S OFFER
Tool Joint O.D.
Type of Hardbanding Yes, as specifed
Type of Internal Coating Plastic coating
Condition
Brand New c/w Thread protectors
Date of last inspection Brand New
d Drill Pipe 4
Length 6500 ft
Pipe Body O.D. 4”
Range Range 2
Weight 15.7 ppf
Class G-105
Connection 3-1/2” IF
Tool Joint O.D.
Type of Hardbanding Yes, as specifed
Type of Internal Coating Plastic coating
Condition
Brand New c/w Thread protectors
Date of last inspection Brand New
ITEM DESCRIPTION OF EQUIPMENT MINIMUM REQUIREMENTS CONTRACTOR’S OFFER
eDrill Pipe Pup Joints
Drill Pipe #1 - Number
At least 2 pup joints for each drill pipe should be
supplied. New or premium with thread
2 each 5” pup joints
Lengths 5’, 10’ and 15’
Type of
hardbanding Smooth, fine protectors Yes, as specified
Drill Pipe #2 - Number
2 each 3-1/2” pup joints
Lengths 5’, 10’ and 15’
Type of hardbanding Smooth, fine Yes, as specified
Drill Pipe #3 - Number
2 each 5” pup joints
Lengths 5’, 10’ and 15’
Type of hardbanding Smooth, fine Yes, as specified
Drill Pipe #4 - Number
2 each 4” pup joints
Lengths 5’, 10’ and 15’
Type of hardbanding Smooth, fine Yes, as specified
eHeavy Weight Drill Pipe 1
Number of joints 36 36
ITEM DESCRIPTION OF EQUIPMENT MINIMUM REQUIREMENTS CONTRACTOR’S OFFER
Pipe Body O.D. 5 inch 5”
Range 2 Range 2
Weight 50 ppf
Class
Connection 4 ½” IF
Tool Joint O.D.
Type of Hardbanding Smooth, fine Smooth, Fine
Type of Internal Coating None Plastic lining
ConditionNew or premium with
thread protectors Thread protectors
Date of last inspection New, Jan 2009
fHeavy Weight Drill Pipe 2
Number of joints 20 20
Pipe Body O.D. 3-1/2 inch 4-1/2”
Range 2 2
Weight 40.69 ppf
Class Brand New
Connection NC 46
Tool Joint O.D. 6-1/4”
ITEM DESCRIPTION OF EQUIPMENT MINIMUM REQUIREMENTS CONTRACTOR’S OFFER
Type of Hardbanding Smooth, fine Smooth, Fine
Type of Internal Coating None Plastic lining
ConditionNew or premium with
thread protectors Brand New
Date of last inspection New, Jan 2009
g Drill Collars 1
Number of joints 4 6
Drill Collar O.D. 9 inch 9 ½”
Drill Collar I.D. 3 inch 3”
Weight, lb/ft 217 ppf
Connection 7-5/8" reg. 7 5/8” Reg
Spiral or Plain Spiral
Elevator and Slip Recess or not
With elevator and slip recess
ConditionNew or Premium condition
with thread protectors Brand New
Date of last inspection Brand New
h Drill Collars 2
Number of joints 24 24
Drill Collar O.D. 8 inch 8”
ITEM DESCRIPTION OF EQUIPMENT MINIMUM REQUIREMENTS CONTRACTOR’S OFFER
Drill Collar I.D. 2-13/16 inch 2-13/16”
Weight, lb/ft 150 ppf
Connection 6-5/8" Reg. 6 5/8” Reg
Spiral or Plain Spiral Spiral
Elevator and Slip Recess or not Yes Yes
ConditionNew or Premium condition
with thread protectors Brand New
Date of last inspection Brand New
i Drill Collars 3
Number of joints 30 30
Drill Collar O.D. 6-1/2 inch 6 ½”
Drill Collar I.D. 2-13/16 inch 2-13/16”
Weight, lb/ft 92 ppf
Connection 4-1/2" IF NC 46
Spiral or Plain Spiral Spiral
Elevator and Slip Recess or not Yes Yes
ConditionNew or Premium condition
with thread protectors Brand New
Date of last inspection Brand New
ITEM DESCRIPTION OF EQUIPMENT MINIMUM REQUIREMENTS CONTRACTOR’S OFFER
j Drill Collars 4
Number of joints 20 24
Drill Collar O.D. 4-3/4 inch 4 ¾”
Drill Collar I.D. 2-1/4 inch 2-1/4”
Weight, lb/ft 47 ppf
Connection 3-1/2" IF 3 ½” IF
Spiral or Plain Spiral Spiral
Elevator and Slip Recess or not Yes Yes
ConditionNew or Premium condition
with thread protectors Brand New
Date of last inspection Brand New
k Drill Collars 5
Number of joints
Drill Collar O.D.
Drill Collar I.D.
Weight, lb/ft
Connection
Spiral or Plain
Elevator and Slip Recess or not
Condition
ITEM DESCRIPTION OF EQUIPMENT MINIMUM REQUIREMENTS CONTRACTOR’S OFFER
Date of last inspection
lPony Drill Collars
Number/Size/Length/Conn
2 / 9 ½”” / 10 ft / 7 5/8” Reg
Condition Brand New
Number/Size/Length/Conn
2 / 8” / 10 ft / 6 5/8” Reg
Condition Brand New
Number/Size/Length/Conn
2 / 6 ½” / 10 ft / NC 46
Condition Brand New
mNon-Magnetic Drill Collars
Number/Size/Length/Conn
Condition
Number/Size/Length/Conn
Condition
nBit Subs/Drilling Subs
As a minimum Contractor must provide:
(a) 2 ea of all required bit
subs bored for float Yes, as specified
(b) 2 ea of all crossover Yes, as specified
ITEM DESCRIPTION OF EQUIPMENT MINIMUM REQUIREMENTS CONTRACTOR’S OFFER
subs to be able to run all drill string items and
fishing tools
All subs should be of sufficient length to not be
unduly stressed when drilling.
Yes, as specified
Bidders should provide a complete list of all subs to
be provided, with full dimensions.
Yes, as specified
oDrill Pipe Float Valves
Make/Model/Size for 12-1/4", 17-1/2" & 18-1/2" bits
Bakerline Model F, 5F-6R
China, Float Valve Model F for 12-
1/4” and 17-1/2” Bit
Make/Model/Size for 9-5/8" to 8-1/2" bits
Bakerline Model F, 4R China, Float Valve Model F for 8-1/2”
Bit
Make/Model/Size for 6" to 6-1/4" bits
Bakerline Model F, 2F-3R
China, Float Valve Model F for 6-1/4”
Bit
p Totco Baffle Plates
Make/Model/Size for 18-1/2" bits 2 ea
China / 2 ea
Make/Model/Size for 17-1/2" bits 2 ea
China / 2 ea
Make/Model/Size 2 ea China / 2 ea
ITEM DESCRIPTION OF EQUIPMENT MINIMUM REQUIREMENTS CONTRACTOR’S OFFER
for 12-1/4" bits
Make/Model/Size for 8-1/2" bits 2 ea
China / 2 ea
q Stabilizers
26" String Stabilizers 1 ea, Welded Type
3 ea 26" String Stabilizers
26" Nearbit Stabilizers
2 ea 26" Nearbit Stabilizers
17-1/2" String Stabilizers 2 ea, IBS Type
6 ea 17-1/2" String Stabilizers
17-1/2" Nearbit Stabilizers 1 ea, IBS Type
2 ea 17-1/2" Nearbit Stabilizers
12-1/4" String Stabilizers 2 ea, IBS Type
6 ea 12-1/4" String Stabilizers
12-1/4" Nearbit Stabilizers 1 ea, IBS Type
2 ea 12-1/4" Nearbit Stabilizers
8-1/2" String Stabilizers 3 ea, IBS Type
6 ea 8-1/2" String Stabilizers
8-1/2" Nearbit Stabilizers 1 ea, IBS Type
2 ea 8-1/2" Nearbit Stabilizers
6" String Stabilizers 3 ea, IBS Type
6 ea 6" String Stabilizers
6" Nearbit Stabilizers 1 ea, IBS Type
2 ea 6" Nearbit Stabilizers
r Drilling Jars
8" Drilling Jars 1 ea 8” Drilling jar
ITEM DESCRIPTION OF EQUIPMENT MINIMUM REQUIREMENTS CONTRACTOR’S OFFER
6-3/4" Drilling Jars
1 ea 6 ½” Drilling jar
4-3/4" Drilling Jars
1 ea 4 ¾” Drilling jar
2.27 OTHER DRILLING TOOLS
ITEM DESCRIPTION OF EQUIPMENT MINIMUM REQUIREMENTS CONTRACTOR’S OFFER
2.27OTHER DRILLING TOOLS
a Hole Openers
36" Hole-Opener Not required.
26" Hole-Opener1 ea Grant or equiv.
c/w 2 sets milled tooth cutters
1 ea 26” Hole opener c/w 2 sets
milled tooth cutters
17-1/2" Hole-Opener 1 ea Grant or equiv. c/w 2 sets milled
1 ea 17-1/2” Hole opener c/w 2 sets
ITEM DESCRIPTION OF EQUIPMENT MINIMUM REQUIREMENTS CONTRACTOR’S OFFER
tooth cuttersmilled tooth
cutters
b Underreamers
26" Underreamer Not required.
c Roller Reamer
Roller Reamer for 8-1/2" hole
Roller Reamer 1 ea for size 28”,
22”, 17-1/2”, 16”, 12-1/4”, 8-1/2”,
and 6-1/8”
d Shock Subs
8" Shock Subs 1 jt 8" Shock Subs
6-1/2" Shock Subs
1 jt 6-1/2" Shock Subs
e Casing Scrapers
For 9-5/8" casing (weight as per program)
1 ea Bowen or equiv.
1 ea China 9-5/8” casing scrapper
For 7" casing (weight as per program)
1 ea Bowen or equiv.
1 ea China 7” casing scrapper
2.28 FISHING TOOLS
ITEM DESCRIPTION OF EQUIPMENT MINIMUM REQUIREMENTS CONTRACTOR’S OFFER
2.28
FISHING TOOLS
a Overshots
China / Overshot 10-5/8" OD
China / Overshot 8-3/8" OD
China / Overshot 5-3/4" OD
All overshot complete with
basket and spiral grapples
Make/Size/Type to catch 9" Drill Collars
Bowen/11-3/4"/150F.S. or equiv.
Grapples (basket & spiral)
A range. Bidders to list
Make/Size/Type to catch 8" Drill Collars
Bowen/9-5/8"/150F.S. or equiv.
Grapples (basket & spiral)
A range. Bidders to list
Make/Size/Type for 5" & 6-3/4" DP & DC's
Bowen/8-1/8"/150F.S. or equiv.
Grapples (basket & spiral)
A range. Bidders to list
Make/Size/Type for 3-1/2" DP & 4-3/4" DC's
Bowen/5-3/4"/150F.S. or equiv.
Grapples (basket & spiral)
A range. Bidders to list
Oversize Lip Guides Bidders to list
b Spears
Make/Size/Type for Bowen
China / 2 3/8” & 2 7/8” Tubing and 5 ½”, 7”,9 5/8” and
13 3/8” Casing
c Taper Taps
Make/Size/Type for 2- 1 ea Bowen or China / 2 ea / 3 ¼”
ITEM DESCRIPTION OF EQUIPMENT MINIMUM REQUIREMENTS CONTRACTOR’S OFFER
7/8",
3-1/2" & 5" DPequiv. to 4 ¼” and 1 ¾”
to 3 1/3”
d Safety Joints
Make/Size/Type for 8" Drill Collars
1 ea Bowen or equiv.
1 ea, China safety joint for 8” DC
Make/Size/Type for 6-3/4" Drill Collars
1 ea Bowen or equiv.
1 ea, China safety joint for 6-3/4” DC
e Fishing Bumper Subs
Make/Size/Type for 8" Drill Collars
1 ea Bowen or equiv.
1 ea Fishing bumper sub for 8”
DC
Make/Size/Type for 6-3/4" Drill Collars
1 ea Bowen or equiv.
1 ea Fishing bumper sub for 6-
3/4” DC
Make/Size/Type for 4-3/4" Drill Collars
1 ea Bowen or equiv.
1 ea Fishing bumper sub for 4-
3/4” DC
f Fishing Jars
Make/Size/Type for 8" Drill Collars
1 ea Bowen type Z or equiv.
1 ea Fishing jar for 8” DC
Make/Size/Type for 6-3/4" Drill Collars
1 ea Bowen type Z or equiv.
1 ea Fishing jar for 6-3/4” DC
Make/Size/Type for 4-3/4" Drill Collars
1 ea Bowen type Z or equiv.
1 ea Fishing jar for 4-3/4” DC
g Junk Subs
Make/Size/Type for 12- 1 ea Bowen or 1 ea Junk sub for
ITEM DESCRIPTION OF EQUIPMENT MINIMUM REQUIREMENTS CONTRACTOR’S OFFER
1/4" hole equiv. 12-1/2” hole
Make/Size/Type for 8-1/2" hole
1 ea Bowen or equiv.
1 ea Junk sub for 8-1/2” hole
Make/Size/Type for 6" hole
1 ea Bowen or equiv.
1 ea Junk sub for 6” hole
hReverse Circulation Junk Baskets
Make/Size/Type for 11-3/4" to 12-1/4" hole
1 ea Bowen or equiv.
1 ea Reserve Circulating Junk Basket 11" OD
Make/Size/Type for 8-1/2" to 9-1/2" hole
1 ea Bowen or equiv.
1 ea Reserve Circulating Junk 7-
7/8" OD
i Fishing Magnets
Make/Size/Type for 12-1/4" hole
1 ea Bowen or equiv.
1 ea Fishing Magnet c/w Flush,
11 1/2" OD
Make/Size/Type for 8-1/2" hole
1 ea Bowen or equiv.
1 ea Fishing Magnet c/w Flush,
8" OD
k Junk Mills
Make/Size/Type for 17-1/2" hole
1 ea Bowen or equiv.
1 ea Junk mill for 17-1/2” hole
Make/Size/Type for 12-1/4" hole
1 ea Bowen or equiv.
1 ea Junk mill for 12-1/4” hole
Make/Size/Type for 8-1/2" 1 ea Bowen or 1 ea Junk mill for
ITEM DESCRIPTION OF EQUIPMENT MINIMUM REQUIREMENTS CONTRACTOR’S OFFER
hole equiv. 8-1/2” hole
2.29 DRILL STRING HANDLING TOOLS
ITEM DESCRIPTION OF EQUIPMENT MINIMUM REQUIREMENTS CONTRACTOR’S OFFER
2.29DRILL STRING HANDLING TOOLS
aBit Breakers and Ring Gauges
26" Bit Breaker & Ring Gauge
1 ea1 ea 26" Bit
Breaker & Ring Gauge
18-1/2" Bit Breaker & Ring Gauge
1 ea1 ea 18-1/2" Bit Breaker & Ring
Gauge
17-1/2" Bit Breaker & Ring Gauge
1 ea1 ea 17-1/2" Bit Breaker & Ring
Gauge
12-1/4" Bit Breaker & Ring Gauge
1 ea1 ea 12-1/4" Bit Breaker & Ring
Gauge
8-1/2" Bit Breaker & Ring Gauge
1 ea1 ea 8-1/2" Bit Breaker & Ring
Gauge
6" Bit Breaker & Ring Gauge
1 ea1 ea 6" Bit Breaker
& Ring Gauge
ITEM DESCRIPTION OF EQUIPMENT MINIMUM REQUIREMENTS CONTRACTOR’S OFFER
b Drill Collar Lift Subs
Lift Subs for 9" Drill Collars 2 ea
3 ea lifting sub for 9” DC
Lift Subs for 8" Drill Collars 5 ea
5 ea lifting sub for 8” DC
Lift Subs for 6-3/4" Drill Collars 5 ea
5 ea lifting sub for 6-3/4” DC
Lift Subs for 4-3/4" Drill Collars 3 ea
5 ea lifting sub for 4-3/4” DC
c Safety Clamps
Make/Type/Size for 9" Drill Collars
1 Varco or equiv.1 ea China Safety Clamp for 9” DC
Make/Type/Size for 8" Drill Collars
1 Varco or equiv.1 ea China Safety Clamp for 8” DC
Make/Type/Size for 6-3/4" Drill Collars
1 Varco or equiv.1 ea China Safety Clamp for 6-3/4”
DC
Make/Type/Size for 4-3/4" Drill Collars
1 Varco or equiv.1 ea China Safety Clamp for 4-3/4”
DC
d Elevators
Centre Latch Elevators for: 8"/6-3/4"/4-3/4" DC's
1 ea
2 set China center latch elevator
available for each size DC
Centre Latch Elevators for: 5"/3-1/2" DP (250 tons)
2 ea 2 set China center latch elevator
available for each
ITEM DESCRIPTION OF EQUIPMENT MINIMUM REQUIREMENTS CONTRACTOR’S OFFER
size DP
Centre Latch Type Elevators for: 3-1/2" & 2-7/8" tubing
1 ea
1 set China center latch elevator
available for each size tubing
Make/Type/Size
e Rotary Slips
Make/Type/Size fo r: 9"/8"/6-1/2"/4-3/4" DC
1 ea, Varco or equiv.
1 set China rotary slip available for
each size DC
Make/Type/Size for: 5"/3-1/2" DP
2 ea, Varco or equiv.
1 set China rotary slip available for
each size DP
Make/Type/Size for: 3-1/2" & 2-7/8" TBG
1 ea, Varco or equiv.
1 set China rotary slip available for each size Tubing
Make/Type/Size Power Slips for 5"/3-1/2" DP
1 ea, Varco or equiv.
1 set China power slip available for
each size DP
f Rotary Tongs
Tongs with jaw assemblies for 20" casing
1 set, Web Wilson or equiv.
1 set 3-3/8” to 13-3/8” available
Tongs with jaw assemblies for 3-1/2 - 5",
1 set, BJ Model DB or equiv. 1 set available
5"-6-3/4", 6-5/8"-9", 9"-10-3/4", 11-3/4"-13-3/8".
Make/Type/Size China / LW 13.374
ITEM DESCRIPTION OF EQUIPMENT MINIMUM REQUIREMENTS CONTRACTOR’S OFFER
Hydraulic Tongs
Heavy Duty Tongs for 3-1/2" & 2-7/8" TBG
2 sets, Petol or equiv.
2 set Heavy Duty Tongs
Make/Type/Size3-1/2" & 2-7/8"
Tubing
Tongs c/w 2 jaw assys for 3-1/2" & 2-7/8" TBG
1 set, BJ Model C or equiv.
1 set manual tong
Make/Type/Size
3-1/2" & 2-7/8" Tubing
g Drill Pipe Spinner
Drill Pipe Spinning Wrench for 5" & 3-1/2" DP
1 ea, Varco or equiv.
China, Hydraulic Drill Pipe Spinner
Make/Type/Size
h Tubing Power Tongs
Power Tong with jaws for 3-1/2" & 2-7/8" tbg 1 ea, Eckel or equiv.
1 ea Power tubing tong
Make/Type/Size
3-1/2" & 2-7/8" Tubing
2.30 CASING HANDLING TOOLS
ITEM DESCRIPTION OF EQUIPMENT MINIMUM REQUIREMENTS CONTRACTOR’S OFFER
2.30CASING HANDLING TOOLS
a Elevators
Side Door Elevator, 150 ton for 20",16", 13-3/8",
1 ea
China, 2 ea Side Door Elevator for 20”, 13-3/8”, 9-
5/8”, and 7” casing
9-5/8", 7" casing. Make/Type/Size
Single Joint Elevator for 20", 16",13-3/8", 9-5/8", and
1 ea
China, 2 ea Single joint elevator for 20”, 13-3/8”, 9-
5/8”, and 7” casing
7" casing c/w swivel and suspension cable
Make/Type/Size
b Rotary Slips
Casing Slips for 20"/16",13-3/8"/9-5/8"/7" and 4-1/2" casing
1 ea, Varco or equiv.
China, Casing Slip for 20”, 13-3/8”, 9-
5/8”, and 7” casing
Make/Type/Size
c Rotary Tongs
Tongs with extended jaws to run 20" casing
1 set Web Wilson or equiv.
China, Rotary Tong w/ jaws
ITEM DESCRIPTION OF EQUIPMENT MINIMUM REQUIREMENTS CONTRACTOR’S OFFER
except 20” casing
Make/Type/Size
dCasing Handling Spiders & Elevators
Air operated, slip type, 500 ton Spider/Elev. Combination c/w slip inserts for 20",13-3/8",9-5/8" and 7" casing. To be complete with guide plates for all casings and adaptor plate for rotary table if required.
1 set, BJ or Varco or equiv.
China, Air operated, Slip
Type 350 ton with slip insert for 20”, 13-3/8”, 9-5/8”, and 7” Casing
Make/Type/Size
e Elevator Links
132" Weldless 500 ton Links 1 set
1 set 132’ – 350 Ton Link
Make/Type/Size
98" Weldless 500 ton Links 1 set
1 set 142’ – 500 Ton Link
Make/Type/Size
98" weldless 350 ton links 2 sets
2 set 98” – 350 Ton Link
Make/type/Size
f Power Tongs
Power Tongs c/w jaws to run 20",13-3/8",9-5/8",7”
1 ea, Weatherford Model 1600 or
China, Power Tong w/ jaws from 4-
ITEM DESCRIPTION OF EQUIPMENT MINIMUM REQUIREMENTS CONTRACTOR’S OFFER
casing equiv. 1/2” to 13-3/8”
7"/4-1/2" casing. Make/Type/Size
China, Casing Power Tong /
Model TQ340-35Y
Hydraulic Power Pack to run csg & tbg tongs
1 ea, Weatherford 60 HP or equiv.
China, Hydraulic Power Pack
Make/Type/Size
g Bushings and Bowls
Make/TypeAll required
Bushings and Bowls to run all
All Bushing and bowls to run all
drill string
Insert bowls 20", 13-5/8" Drill String
components and casing sizes
Insert bowls 20", 13-5/8"
Insert bowls 10-3/4" - 9-5/8"
Insert bowls 10-3/4" - 9-5/8"
Insert bowls 9-5/8" or less
Insert bowls 9-5/8" or less
Casing Bushing Casing Bushing
Bit breaker adapter
Bit breaker adapter
hCirculating Heads / Cementing Eqpt
C-plate for inner string cementing on 20" csg
1 ea1 ea C-plate 20”
Casing
13-3/8" BTC Circulating Head
Cementing Service Company to Supply
ITEM DESCRIPTION OF EQUIPMENT MINIMUM REQUIREMENTS CONTRACTOR’S OFFER
9-5/8" Premium Circulating Head
Cementing Service Company to Supply
7" Premium Circulating Head
Cementing Service Company to Supply
5" & 3-1/2" DP Circulation Head
1 ea1 ea 5” and 3-1/2”
DP circulating head
Side Entry Circulating Sub
1 ea 2" x 4-1/2"IF pin x box
1 ea Side entry circulating sub
with conn 4-1/2” IF pin x box
Chicksans (1502 unions only) 60 ft x 2"
1 set Chicksan loop 1502 60’ x 2”
2.31 TRANSPORTATION EQUIPMENT (See Notes)
2.32 CAMP AND OFFICE FACILITIES (See Notes )
2.33 SAFETY & FIRE PREVENTION EQUIPMENT
2.33SAFETY & FIRE PREVENTION EQUIPMENT
aHazardous Area Classification
Describe and supply drawings
Bidders to describe how the Drilling Unit
complies with a recognized
Hazardous Area Classification
System.
Drawings are to be supplied together with equipment
features.
Drawings provided
bEngine Safety Systems
Describe
Engines should have overspeed
shutdown devices, spark arrest
mufflers, and other emergency systems.
Yes, available
cGas Detectors/Monitors
List and describe No/Make/Type/Location
Basic Gas Detection Equipment is
required.Yes, available
The system should
comprise the following:
(a) A fixed system with monitors to
detect combustible gases and H2S.
4 Gas detectors, located at bell nipple, shale
shaker and mud tank
(b) Portable detectors for
combustible gases
Yes, available
and H2S.
d Fire Extinguishers
List and describe the Numbers/Makes/Sizes/
Contractor to supply sufficient fire
Classes/Locations of all fire extinguishers.
extinguishers of an appropriate
class/size for both the rig and camp. All units are to be
regularly inspected and tagged.
10 x 12” fire extinguisher located at all
important places in rig site and camp office
eSling & Lifting Equipment Certification.
List and describe Make/Type/Size/Rating of
Contractor is to supply sufficient sets of approved
slings
Sufficient certified slings are available
all Contractor's slings. State the certifying authority and date of certification.
f Safety Lines & Belts
Safety Lines and belts are to be
available and used as per IADC and
good oilfield practice.
Yes, as specified
List and describe
g Personal Safety Equipment
Contractor is to ensure that
hardhats, safety boots, gloves,
safety glasses and
All PPE equipments as per
IADC safety practice provided
other personal protective
equipment are available and used
as per IADC and good oilfield
practice.
List and describe
h Breathing Apparatus5 ea 15 min BA
Escape Sets
List and describe SCBA equipment.
Company will supply additional H2S
Safety Equipment
10 ea 5 minutes respirator
15 ea 30 minutes respirator
List & describe breathing air compressor equipment.
MCGH/ Sh Breathing Air
Compressor Unit
i Warning Signs
Appropriate warning signs are required both at the rig and
camp.
List and describe Safety Sign : Mandatory :
Wear rubber glove, Ear protection must be worn, head protection must be worn, Eye protection must be worn, foot protection must be worn, wear goggles, use dust masker.
Safe Condition : Muster Station, Emergency shower, exit road.
Prohibition : No smoking, No jewellery,
Warning : Danger Highly Flammable, Harzadous area, Danger High voltage, Toxic H2S Gas
jPermit to Work System
Describe Contractor is to have and use a permit to work
system
Work Permits : Hot Permit Cold Permit Confine space
entry permit Electrical
Permit Pressure Permit Explosive/
Radioactive Permit
k Safety Policy
Describe
Safety Policy : Smoking police Drug and
Alcohol policy Right to work
safelyHSE and training
policy
l Safety Manual
Supply copy
Safety procedure manual
2.34 ADDITIONAL EQUIPMENT
ITEM DESCRIPTION OF EQUIPMENT MINIMUM REQUIREMENTS CONTRACTOR’S OFFER
2.34ADDITIONAL EQUIPMENT
This space is provided for the inclusion of additional rig equipment.
Top drive complete with
independent VFD and Hydraulic
Unit, Capacity 500 Ton, Manufactured
by BPM