Upload
others
View
1
Download
0
Embed Size (px)
Citation preview
LEDi® ORiGiNALREF : 93000011REF : 93000024
MODE D’EMPLOi - page 3
USER GUiDE - page 9
MDE-LEDI-ORIGINAL-1101V3.0
2 MDE-LEDI-ORIGINAL-1101V3.0
ATTENTION ! Avant de commencer l’installation de votre matériel, lisez attentive-ment la section suivante qui décrit les consignes de sécurité à respecter au cours de l’installation.
L’installation électrique sur laquelle le matériel est raccordé doit être réalisée conformément à la norme NF C 15-100 .
Cet appareil ne comporte pas d’interrupteur d’alimentation primaire : un dispositif de coupure (disjoncteur ou interrupteur sectionneur), rapidement accessible, doit être incorporé dans l’installation de câblage. Ce dispositif doit supporter les va-leurs de tension et courant nominales indiquées sur l’appareil.
En Europe : dans le cadre de la protection des individus et de l'environnement, il vous incombe de vous débarrasser de cet équipement dans un site de collecte prévu à cet effet (séparément des ordures ménagères). Pour de plus amples informations, contactez votre revendeur, votre site de collecte ou les autorités locales compétentes.
Toute modification ou ouverture du produit sans l’accord du SAV entraîne la perte de la garantie.
Toute opération de maintenance doit être effectuée hors-tension.
Gorgy Timing décline toute responsabilité en cas d’accidents ou de dommages provoqués par une mauvaise utilisation du produit.
Les produits GORGY TiMiNG sont conformes aux normes : CE, EN 60950, EN 55022, EN 50024.
CONSiGNES DE SéCURiTé iMPORTANTES
SOMMAiRE
MDE-LEDI-ORIGINAL-1101V3.0 3
SOMMAiRE
1. PRiNCiPE DE MONTAGE ............................................................................................. 41.1. FIXATION MURALE ............................................................................................................ 41.2. FIXATION ENCASTRABLE ................................................................................................. 4
2. CARACTéRiSTiQUES GéNéRALES ........................................................................... 5
3. iNFORMATiONS ........................................................................................................... 5
4. BRANChEMENTS ......................................................................................................... 65.1. Configuration avancée ......................................................................................................... 65.2. Configuration date / heure .................................................................................................... 7
5. CONFiGURATiON ViA L’hORLOGE (BOUTONS) ....................................................... 6
6. REDéMARRAGE ........................................................................................................... 7
4 MDE-LEDI-ORIGINAL-1101V3.0
2. CARACTéRiSTiQUES GéNéRALES1. PRiNCiPE DE MONTAGE
1.1. FiXATiON MURALE
1.2. FiXATiON ENCASTRABLE
Préparation du support : ► Réaliser une ouverture aux dimensions de l’horloge. ► Placer la plaque support et la fixer à l’aide de chevilles et vis Ø 3 mm (Chevilles et vis
non fournies). ► Placer l'horloge dans le logement. Celle-ci sera maintenue automatiquement par magnétisme.
150 mm 7 mm
15 m
m
14 m
m
ø7
5°
85 m
m
270 mm
270
mm
Câble d'alimentation
62 m
m
86 m
m
ACCROCHAGE DE L'HORLOGE AVEC VERROUILLAGE
1
2
Verrouillage par déplacement de l'horloge vers la droite
250 mm
250
mm
260
mm
Trou de fixation 260 mm= =
Alimentation
Horloge
Vis Ø 3mm
Support encastrable
Ouverture murale
mini 65mm
MDE-LEDI-ORIGINAL-1101V3.0 5
2. CARACTéRiSTiQUES GéNéRALES
► Affichage numérique heure, minute, 7 segments à diodes électroluminescentes. ► Inclinaison des chiffres : 10°. ► Alimentation : 230VAC/50-60Hz ► Sauvegarde par pile Lithium incorporée. ► LED bi-couleurs blanche et bleue. REF : 93000011
ou ► LED tri-couleurs rouge/verte/jaune. REF : 93000024 ► Dimensions : 270x270x62 mm (LxHxP) ► Poids : 1.7 kg ► Hauteur des chiffres : Heure/minute : 50 mm ► Vague des secondes : 60 points ► Version autonome :
Base de temps à quartz TCXO incorporé 32Khz. ► Gamme LEDi® : Boîtier standard – Fixation murale et encastrable
3. iNFORMATiONS
En cas de coupure secteur l’affichage s’éteint mais l’heure est sauvegardée grâce à sa pile interne.
OFF
ON
-
+
PROG
► Tous les réglages s’effectuent au moyen des 3 touches ‘+’, ‘-’ et ‘PROG’ situées à l’arrière du produit.
► Un défilement rapide s’effectue par une pression conti-nue sur les boutons poussoirs.
► Pour sortir d’un menu, il suffit de rester appuyé 2 secondes sur le bouton ‘PROG’. La sortie du menu est automatique en cas d’inactivité de plus de 70 secondes.
► La luminosité de l’afficheur est réglable, hors menu, grâce à un appui sur les boutons ‘+’ et ‘-’.
► Offset : permet d’indiquer le fuseau horaire par rapport à l’heure UTC (Universal Time Coordinated).
► DST (Daylight Saving Time) : permet de renseigner la politique de changement d’heure (été / hiver)
6 MDE-LEDI-ORIGINAL-1101V3.0
☛ Fixer l’horloge sur son support avant de la raccorder sur le secteur.
► Raccorder l’horloge au secteur.
► Mettre l’horloge en fonctionnement en basculant le commutateur situé au dos de l’hor-loge sur la position ON (position basse).
☛ Seul l’affichage central de l’horloge est représenté sur les synoptiques suivants. Le symbole ▼ indique que le digit clignote.
5.1. CONFiGURATiON AVANCéE
exemple : pour la France, il faut renseigner : ► Signe de l’offset : dt + ► Valeur de l’offset : 100 ► Réglage du DST : EU (Europe)
5. CONFiGURATiON ViA L’hORLOGE (BOUTONS)
Signe de l'offset
PROG 4 sec.
PROG
Valeur de l'offset
PROG
Réglage du DST
+ / -
+ / -
+ / -
OFF : Pas d'heure d'étéEU : EuropeUS : Amérique du nordAU : Australie
Affichage date - heure
Affichage date - heure
Réglage synchronisation+ / -
PROG
PROG
Réglage format de l'heure+ / - 12hh : Mode 12 heures24HH : Mode 24 heures
ASCII : ON ↔ OFF
PROG
Ce réglage n'a aucun effetsur ce produit
000 : Offset de 0 heure 0 minute030 : Offset de 30 minutes100 : Offset de 1 heure130 : Offset de 1 heure 30 minutes...
4. BRANChEMENTS
MDE-LEDI-ORIGINAL-1101V3.0 7
5.2. ConfIgUrATIon DATE / HEUrE
► Reset : Appuyer sur le bouton "RESET" situé en face arrière du produit. Cette opération va remettre l’horloge dans sa configuration usine. Tous les paramètres seront reinitialisés.
Configuration matériel :Adresse - Version logiciel
Réglage de l'année
Réglage du mois
PROG
PROG
PROG
PROG
Réglage du jour
PROG
Réglage des heures
PROG
Réglage des minutes
PROG
Réglage couleur digits
PROG
Réglage couleur vague
PROG
+ / -
+ / -
+ / -
+ / -
+ / -
+ / -
+ / -
d1 : Blancd2 : Blanc/bleud3 : Bleu
v1 : Blancv2 : Blanc/bleuv3 : Bleu
d1 : Rouged2 : Jauned3 : Vert
v1 : Rougev2 : Jaunev3 : Vert
Affichage date - heure
Affichage date - heure
Temps d'alternance pourl'affichage de la date
Temps d'affichage de l'heure (en seconde)Mettre 0 pour ne pas afficher
Configuration matériel :Adresse - Version logiciel
PROG
PROG
Affichage date - heure
Temps d'alternance pourl'affichage de l’heure
Temps d'affichage de l'heure (en seconde)Mettre 0 pour ne pas afficher
ATTENTIONProgrammez à l’heure UTC/GMTPour la France, -2 heures en été
et -1 heure en hiver.
REF : 93000011
ou
REF : 93000024
6. REDéMARRAGE
8 MDE-LEDI-ORIGINAL-1101V3.0
RADIO TIMING®, LEDI®, LEDICA®, HANDI® sont des marques déposées GORGY TIMING.Numéro de déclaration d’activité de prestataire de formation : 82 38 04877 38GORGY TIMING RC 74 B 38 - Toutes modifications d'ordre technique ou esthétique peuvent être apportées sans préavis.
SUPPORT TECHNIQUE
DEPUIS LA FRANCE SUR UN POSTE FIXE :
GORGY TiMiNG SAS Quartier Beauregard
38350 La Mure d'isère (Grenoble France) Phone: +33 4 76 30 48 20 Fax: +33 4 76 30 85 33
email: [email protected] - www.gorgy-timing.com
9MDE-LEDI-ORIGINAL-1101V3.0
USER GUiDE
LEDi® ORiGiNALREF : 93000011REF : 93000024
EN
GLI
SH
10 MDE-LEDI-ORIGINAL-1101V3.0
WARNING! Read the section that follows very carefully before installing your equipment. It gives the safety instructions to follow during installation.
The electrical installation to which the equipment is connected must comply with the NF C 15-100 standard.
This device does not have a primary power switch. A power protection system (cir-cuit-breaker or disconnecting switch), easy to access must be built into the wiring installation. This device must support the nominal voltage and current values spe-cified on the clock.
In Europe: to comply with European regulations on the protection of persons and the environment, you must dispose of this equipment in a collection site provided for this purpose (separately from household waste). Contact your reseller, collec-tion site or the competent lcoal authorities for more information.
Modifying or opening the product without the consent of the Customer servicedepartment will void the warranty.
All maintenance operation shall be conducted with power shut off, including sys-tems connected on relay outputs if any.
Gorgy Timing disclaims all responsibility in case of accident or damage caused by an improper use of the product.
gorgY TIMIng products are compliant with the following standards: CE, En 60950, EN 55022, EN 50024
iMPORTANT SAFETY iNSTRUCTiONS
11MDE-LEDI-ORIGINAL-1101V3.0
1. ASSEMBLY PRiNCiPLE .............................................................................................. 121.1. Wall mounting ..................................................................................................................... 121.2. Flush mounting .................................................................................................................. 12
2. GENERAL ChARACTERiSTiCS ................................................................................. 13
3. iNFORMATiON ............................................................................................................ 13
4. CONNECTiONS ........................................................................................................... 14
5. CONFiGURATiON ViA ThE CLOCK (BUTTONS) ...................................................... 145.1. Advanced settings ............................................................................................................. 145.2. Setting the date and time .................................................................................................... 15
6. REBOOT ...................................................................................................................... 15
EN
GLI
SH
12 MDE-LEDI-ORIGINAL-1101V3.0
2. GENERAL ChARACTERiSTiCS1. ASSEMBLY PRiNCiPLE
1.1. WALL MOUNTiNG
1.2. FLUSh MOUNTiNG
Preparing the wall mounting structure ► Prepare an opening based on your clock dimensions. ► Position the bracket plate and secure it with Ø 3 mm screws (not supplied). ► Insert the clock in the slot. It will be held in place automatically by magnetisation.
150 mm 7 mm
15 m
m
14 m
m
ø7
5°
85 m
m
270 mm
270
mm
Power cable
62 m
m
86 m
m
HANGING OF THE CLOCK WITH LOCKING SYSTEM
1
2
Lock done by movingthe clock to the right
250 mm
250
mm
260
mm
Mounting hole 260 mm= =
Alimentation
Clock
Screw Ø 3mm
Support built
Clock wallopening
mini 65mm
13MDE-LEDI-ORIGINAL-1101V3.0
2. GENERAL ChARACTERiSTiCS
► Digital display for hour, minute, 7 electroluminescent diode segments. ► Tilt of figures: 10°. ► Power supply: 230 VAC / 50-60 Hz ► Data saved with a built-in Lithium battery ► Bi-color LED blue/white. REF : 93000011
or ► Tri-colour LED red/green/yellow. REF : 93000024 ► Dimension: 270x270x62mm (L x H x D) ► Weight: 1.7KG ► Digits height: Hour/Minute 50mm ► Wave of seconds: 60 dots ► Standalone version:
Time base with built-in 32Khz TCXO quartz ► LEDi® range: Standard case – Wall mounting or flush mounting
3. iNFORMATiON
In the event of a mains power outage, the display is switched off, although the time is saved thanks to its internal battery.
OFF
ON
-
+
PROG
► All settings are made using the 3 buttons ‘+’, ‘-’ and ‘Prog’ at the back of the product.
► You can scroll quickly by holding down the pushbuttons.
► To exit a menu, just hold down the ‘Prog’, button
► or leave the buttons inactive for more than 70 seconds.
► You can adjust the display brightness, without going to the menu, by pressing the buttons ‘+’ and ‘-’.
► Offset : enable to indicate the time zone relative to UTC (Universal Time Coordinated).
► DST (Daylight Saving Time) : enable to inform the change (summer/winter).
EN
GLI
SH
14 MDE-LEDI-ORIGINAL-1101V3.0
☛ Fix the clock on its bracket before connecting it to mains power.
► Connect the clock to mains.
► Start the clock running, by tipping the switch located on the back of the clock, to “ON” (low position).
☛ Only the central display is shown on the following synoptic. ▼ Symbol means that the digit is flashing.
5.1. ADVANCED SETTiNGS
example: For France, you shall put: ► Sign of the offset: dt + ► Offset value: 100 ► DST setting: EU (Europe)
5. CONFiGURATiON ViA ThE CLOCK (BUTTONS)
Offset sign
PROG 4 sec.
PROG
Offset value
PROG
Setting of DST
+ / -
+ / -
+ / -
OFF : No DSTEU : EuropeUS : North AmericaAU : Australia
Date - time display
Date - time display
Synchronisation setting + / -
PROG
PROG
Setting of time format+ / - 12hh : 12 hour mode 24HH : 24 hour mode
ASCII : ON ↔ OFF
PROG
This setting has no effecton this product
000 : Offset of 0 hours 0 minutes030 : Offset of 30 minutes100 : Offset of 1 hour130 : Offset of 1 hour 30 minutes...
4. CONNECTiONS
15MDE-LEDI-ORIGINAL-1101V3.0
5.2. SETTiNG ThE DATE AND TiME
► Reset : Press the "RESET" button on the rear panel of the product. This operation will reset the clock in its factory configuration. All parameters are reinitialized.
Configuration matériel :Adresse - Version logiciel
Set year
Set month
PROG
PROG
PROG
PROG
Set day
PROG
Set month
PROG
Set minutes
PROG
Set digit color
PROG
Set wave color
PROG
+ / -
+ / -
+ / -
+ / -
+ / -
+ / -
+ / -
d1 : Whited2 : White/Blued3 : Blue
v1 : Whitev2 : White/Bluev3 : Blue
Affichage date - heure
Date - time display
Time for alternatingthe time display
Time display of the time (in seconds) Set to 0 to not display
Hardware configuration:Address - Software version
PROG
PROG
Date - time display
Time for alternatingthe time display
Time display of the time (in seconds) Set to 0 to not display
d1 : Redd2 : Yellowd3 : Green
v1 : Redv2 : Yellowv3 : Green
WARNINGProgram time in UTC/GMT:
For France, -2 hours in summer, -1 hour in winter.
REF : 93000011
or
REF : 93000024
6. REBOOT
EN
GLI
SH
16 MDE-LEDI-ORIGINAL-1101V3.0
GORGY TiMiNG SAS Quartier Beauregard
38350 La Mure d'isère (Grenoble France) Phone: +33 4 76 30 48 20 Fax: +33 4 76 30 85 33
email: [email protected] - www.gorgy-timing.com
RADIO TIMING®, LEDI®, LEDICA®, HANDI® are trademarks by GORGY TIMING.Number of statement for training provider activity : 82 38 04877 38Gorgy Timing RC74B38 - Any technical, aesthetic, color modifications can be made without notice.
TECHNICAL SUPPORT +33 476 30 48 20