MD-Instruction Manual for Remote Control-Router UPNP Supported

Visionari Limited Liability Company Visionari Copyright(1.5)2010Version

http://www.mydepots.com

1

Manual for Remote View & Control-Router UPNP Supported

H.264 Network

Embedded DVR

INSTRUCTION MANUAL FOR REMOTE VIEW&CONTROL

---------------- Router UPNP Supported----------------



2


Content

Zone A: Setting on DVR interface

Step 1: Plug network line into DVR’s LAN…………………………………………………P3

Step 2~4: Coming into DVR’s network setting interface………..……………………….P3~4

Step 4-1: Setting for 【TYPE】…………………………………………………………….P4

Step 4-1-1~4-1-2: Getting clues for 【IP Addr】&【AUTO DHCP】…………………..P5

Step 4-2: Setting for 【MEDIA PORT】&【WEB PORT】………………………………..P5

Step 4-3: Finding out【DNS】IP………………………………………………………..…..P6

Step 4-4: Restarting DVR system after setting………………………………………………P6

Zone B: Setting on your router

Step 4-5~4-6: Setting on your router…………….. …………………………………………P7

Step 4-7: Checking 【UPNP】status……………………………………………………..…P7

Step 4-8: Methods to Visit DVR…………………….. …………………………………..….P8

Zone C: Setting on remote view interface

Step 4-8-1~4-8-3: How to visit DVR through WAN IP…………………...………….…P8~9

Step 4-9~4-9-4: How to set【DDNS】on DVR interface……………………………….P9~10

Step 4-9-5~4-9-15: How to register for【DDNS】……………………………………. P11~15

Step 4-9-16: Filling 【DDNS】registered clues on DVR interface……………….….……P16

Step 4-9-17~4-9-18: How to visit DVR through 【DDNS】………………………… P16~17

Step 4-9-19: Final scene when Realizing remote view ………………………….…….. P17

Step 5: Setting on remote view interface………………………………………………. P18

Step 6~6-1: Setting visiting password on remote view interface……………….......P18

Attention here: all data below is cited from writer’s local network situation (system fault

parameter is exception), please adjust according to your actual environment.



3


Zone A: Setting on DVR interface

Step 1: Plug network cable line into LAN, assure the light is on, indicating network is normal.

Figure (1)

Figure 1

Step 2：Coming into DVR’s main menu, select 【ADVANCE】，Press【Enter】

Figure 2

Step 3：select 【NETWORK】, Press【Enter】

Figure 3



4


Step 4: You’ll find interface as below and you need fill them accordingly.

Figure 4

Step 4-1:

【TYPE】: Here’re 3 options, you need firstly check whether your router support “UPNP”, if yes,

please select it and follow next steps(if not, please get reference from another manual under

【STATIC】mode)

Figure 4-1



5


Step 4-1-1: when set 【TYPE】as 【DHCP】, at the same time you need set 【UPNP】

as 【OPEN】, in this way, immediately, DVR system will automatically obtain 【IP Addr】

and 【AUTO DHCP】like below,Attention here:

【IP Addr】: Refers to DVR IP address

【AUTO DHCP】: Refers to DNS IP address

Figure 4-1-1

Step 4-1-2: After short while, you’ll find interface result as below:

Figure 4-1-2

Step 4-2:

【MEDIA PORT】: It’s for video transmission via IE, please keep it as default.

【WEB PORT:】: It means “set up the port of IE browser via HTTP”，please input any port

number(But please don’t use system default port 00080, it’s a must to change another), provided

that it’s a 5-digit number and not used by any other device in your wireless environment, i. e, here

assumed we set it as 【09001】.



6


Step 4-3:

【DNS】: you need fill local DNS IP exactly, first input your router’s IP in IE’s address bar, and

land your router’s managing interface, then find 【WAN】, maybe you’ll find two clues for it,

whichever you choose to fill into DVR’s interface, it’s ok!

Figure 4-3

Step 4-4: Writer selects DNS1 to fill, then finish inputting completely. But it’s always

necessary to remember to click 【APPLY】, then 【EXIT】, at this time, DVR system will

restart, if not, please restart manually.

Figure 4-4



7


Zone B: Setting on your router

Step 4-5: Set for your router(Memo: please operate accordingly as your used), input your

router’s IP in Browser’s address bar, and land your router’s managing interface, then find

【UPNP】

Figure 4-5

Step 4-6: To select 【UPNP Service】as Enable,

Figure 4-6

Step 4-7: Check UPNP’s status

Equally, land your router’s managing interface, inspect setting list for UPNP, check whether

DVR’s web port, media port, even mobile port are automatically added here or not.

Figure 4-7



8


Step 4-8: Visiting DVR through WAN IP or DDNS IP

Attention here:

Since WAN IP always change out of your care, so we strongly suggest you visit DVR

through DDNS, of course, it’s precondition is that Step 7 is normal, which indicates

your dvr network is without problem.

Zone C: Setting on remote view interface

Step 4-8-1: Visiting DVR through WAN IP, you need inputting address as：

【http://】+【Your router’s WAN’s IP address】+【:】+【web port】(Must input completely)

Maybe you would ask how to get my router’s WAN IP? Still you need get on your router’s

managing interface like below(Attention: it’s just writer’s router’s IP interface, please check yours

accordingly)

Figure 4-8-1

Step 4-8-2: as you could see how writer operated address correctly.

Figure 4-8-2



9


Step 4-8-3: Of course, for first visiting, system will ask you to install ActiveX, please follow.

Figure 4-8-3

Step 4-9: Visiting DVR through DDNS: which means you could also visiting your DVR

though Dynamic Domain Name Server. But similarly, you need finish corresponding setting.

Go to this interface, and click 【DDNS SETTINGS】.

Figure 4-9

Step 4-9-1: select 【DDNS】as 【ON】

Figure 4-9-1



10


4-9-2：Now you’ll see figure 4-9-2, here’re 3 options for 【SERVICE】

Figure 4-9-2

Step 4-9-3：【SERVICE】: here we recommend to select 【dyndns】

Figure 4-9-3

4-9-4：【HOST NAME】&【USER NAME】 & 【PASSWORD】: you have to get them

through registration on www.dyndns.com, The following steps present you how to catch

clues for the three.

http://www.dyndns.com/



11


4-9-5：Visit website” www.dyndns.com”, and click【Account】

Figure 4-9-5

4-9-6：Click【Create Account】

Figure 4-9-6




12


4-9-7：Fill in application information, like username(“vvmedvr1023” assumed by writer here)

Figure 4-9-7

4-9-8: Now you’ll find interface as below, which reminds you to get useful information from

your email-box.

Figure 4-9-8



13


4-9-9: In your email box, you’ll find an email with topic “Your DynDNS.com Account

Information” from “DynDNS.com Support”, you need click the address.

Figure 4-9-9

4-9-10: Now revisit ” www.dyndns.com”, input username “vvmedvr1023 “& password to

login in.

Figure 4-9-10




14


4-9-11: Click 【Add Host Services】to register “host name”

Figure 4-9-11

4-9-12: Now fill in username you want to use, select correct suffix as”dyndns.org” , and click

“Use auto detected IP…..”, finally, click 【Add To Cart】

Figure 4-9-12



15


4-9-13: Click 【Next】(Memo: don’t worry, your cart contains free services only. You will not

be demanded for credit card information).

Figure 4-9-13

Step 4-9-14: Click 【Activate Services】

Figure 4-9-14

Step 4-9-15: you’ll see interface as below, indicating your services is successfully activated

Figure 4-9-15



16


Step 4-9-16：Ok now back to DVR’s setting interface for 【DDNS】, fill in blank, then press

【APPLY】, and 【EXIT】, DVR will restart, in other words, DVR must restart. You can see writer

filling example from below:

Figure 4-9-16

Step 4-9-17：Till Now, we can try to visit DVR for remote viewing through DDNS, here please

pay most attention on the address inputting，you need input address as:

【http://】+ 【DDNS’s HOSTNAME】+【:】+【web port】, Take writer’s case as example, the

address will be http://vvmedvr123.dyndns.org:9001

Well, still when firstly visit on net, you have to install the ActiveX, please follow:

Figure 4-9-17



17


Step 4-9-18: Fill login information.

【PASSWORD】: For the 1st visit, it’s not necessary to fill(actually you can’t fill), just keep it still

as blank.

【NETWORK】: Select【INTERNET】, click【Login】

Figure 4-9-18

Step 4-9-19：Till now you can see any channel view from DVR’s side like below:（channels you

can see depend on q’ty of dvr’s channel）, here we just take 4-ch dvr as example. You also can

click 【SETUP】to come into control interface.

Figure 4-9-19



18


Step 5: Now click 【SETUP】to set remote control details as your idea.

Figure 5

Step 6: For example, you could also set password, click 【SETTING】, you’ll see:

Figure 6

Among which,

【IE PASSWORD ENABLE】: You must click it as on

【ADMIN PASSWORD】: means you have right to watch & set.

【USER PASSWORD】: means viewers can only watch, have no right to set.

Attention Please:

>>6-1: Only you do set password, visiting interface will ask you to input it. Otherwise you never

need input password.

>>6-2: Remember Only you do set password not only on viewing interface(Figure 6), but also

correspondingly on DVR’s interface(see figure 6-1), the passwords truly work.

.

Figure 6-1

Eventually, you finish

whole process to

realize “ Remote

View” , go to enjoy

now!!

Documents

MD-Instruction Manual for Remote Control-Router UPNP Supported