6
RESUME OBJECTIVE_____ __________________________________________________________ To secure an industrial training in your esteemed organization DATE OF BIRTH____________________________________________________________ __ 09 february 1996 NATIONALITY Indian POSTAL ADDRESS Vikashpuri sec-H5 ,NEW DELHI EMAIL ADDRESS [email protected] [email protected] EDUCATIONAL STATUS Presently in the third year of B.Tech (Bachelor of Technology) program at Mechanical Engineering Department, Giani Zail Singh Campus College of Engineering & Technology, Bathinda. Percentage : 73% (at the end of 5 th semester) 1

MOHIT SINGH RESUME

Embed Size (px)

Citation preview

Page 1: MOHIT SINGH RESUME

RESUME

OBJECTIVE_____ __________________________________________________________

To secure an industrial training in your esteemed organization

DATE OF BIRTH______________________________________________________________ 09 february 1996

NATIONALITYIndian

POSTAL ADDRESSVikashpuri sec-H5 ,NEW DELHI

EMAIL [email protected]

[email protected]

EDUCATIONAL STATUSPresently in the third year of B.Tech (Bachelor of Technology) program at Mechanical Engineering Department, Giani Zail Singh Campus College of Engineering & Technology, Bathinda.

Percentage : 73% (at the end of 5th semester)

RESEARCH INTERESTS Automobile areas Air-Conditioning and Refrigeration Heat Transfer and Mass Transfer Design, Simulation and Optimization of Thermal Systems Manufacturing & material science field

1

Page 2: MOHIT SINGH RESUME

SCHOOL EDUCATION

1. Examination: Senior Secondary School Examination (12th grade) School: Kamla Rai College , Gopalganj Passing Year: 2013 PCM %: 70%

2. Examination: Secondary Examination (10th grade) School: High School Ramchandrapur Passing Year: 2011 PCM %: 85%

PROJECTS

1. B.Tech. Project (junior Thesis)

Topic: Design of Cooling Coils for Air Conditioning ApplicationsDuration: July 2015 to November 2015Guide: Dr. Rajesh Gupta, Associate Professor, Department of Mechanical

Engineering,GZSCCET Bathinda.

This project consisting of design, simulation, fabrication and testing of a novel low cost plastic heat exchanger using extremely thin plastic coils of 3 mm diameter for use in chilled water fan coil unit. Objectives of my work are improvement in heat transfer coefficients and reduction in pressure drop, cost and size of the heat exchanger by the use of very small diameter polypropylene tubes. The design part has been completed and simulation and fabrication of the same will be done in the next stage.

Based on theoretical calculations and extensive literature survey, it has been shown that thin diameter and thin walled plastic tubes if used in heat exchangers can provide for compact heat exchangers while providing a better performance as compared to heat exchangers having metallic coils.

2. B.Tech.( major project )

Topic: Design,Analysis,Prototyping and testing of Wet multi plate clutch for a 1.5T three wheeler.Duration: March 2016 onwardsGuide: Professor Dr. Rajesh Gupta , Associate Professor, Department of Mechanical

Engineering, GZSCCET,Bathinda.

Currently working on this project ,we wants to design,analyse,prototype develop and test an improved clutch suitable for 1.5T three wheeler as the clutch suppliers don’t have any clutch above 1.2T in current production.For this, the approach would be to study the friction material of

2

Page 3: MOHIT SINGH RESUME

driven plates,mean radius of clamping force action,pre-loading of clutch and number of driven plates.

SUMMER INTERNSHIP

Industry: Mahindra & Mahindra limited,Rudrapur (U.K)Topic: Automated manual transmission (AMT).Duration: June2015 to july 2015Guide: Mr. A. N. Verma (R & D Department)

AMT is an electro-hydraulic mechanism for automating manual transmission,which derives from Formula 1.It has a hydraulic system and an electronic system. The electronic transmission control unit helps in engaging and disengaging the clutch and gear through an electronic actuator.It also has a sport mode, which enables driver to move to the manual shifting of gear to increase and decrease the gear ratios with plus and minus either through gear knob/joystick or the steering.In INDIA ,AMT is currently available in three cars-Celerio,Alto K10 and TATA Zest.

AREA OF INTERESTS 1.Automobile sector 2.Industrial production3.Design sector

COMPUTER BACKGROUNDProgramming Languages: BASIC C, C++, VISUAL C++Engineering Packages: MS Office, AutoCAD, Pro-Engineer,Solidwork,

MatlabPlatforms: MS Windows

ACADEMIC HONOURS Awarded Certificate of Merit in Math by school in 10th standard for being

in the top .5% students in the country.

EXTRA CURRICULAR ACTIVITIES1.Our team(ALPHA) bagged 1st position in “OFF ROAD BATTLE 2K16” held by Gautam Buddha University,Noida (U.P), it was a National level competition. I was the head of steering department in that team.

2.. Class Representative (3rd year and graduating batch)

3

Page 4: MOHIT SINGH RESUME

I am the class representative of the graduating batch in Mechanical Engineering Department. I was responsible for creating a consensus among the students on crucial academic issues and acting as a liaison between the student body and the department faculty.

3.. Inter college Cricket Player

Represented the team of GZSCCET,Bathinda at inter college level tournaments in cricket

4.Secured 3rd position in the event Automobile quiz competition held by “Punjab Engineering College,Chandigardh” in north zone.

4.Secured 4th position in the event AUTO QUIZ competition held by “BITS PILANI HYDERABAD CAMPUS”.

5.Secured overall 7th positon in the event Automobile Quiz competition held by “IIT Guwahati”

6.Secured 1st position in the cultural event “Solo Dance Competition’’ held at GZSCCET,Bathinda.

POSITION OF RESPONSIBLITY 1.Convener of “Public relation ,Press note & Invitation committee” at Annual Sports meet of University. 2.Co-convener of “Public relation ,Press note & Invitation committee” at Annual Sports meet of college.3.Co-convener of “Public relation ,Press note & Invitation committee” at Department TECHNO-CULTURAL (MAQUINISTA) Fest.4.Member of “Public relation ,Press note & Invitation committee” at College Annual Fest TARANNUM 2016.5.Member of “Post Function Committee” at Department TECHNO-CULTURAL (YANTRIKI 2015) Fest.

STRENGTH 1.Self confident,Hard working and Will Power.2.Innovative owing to good Conceptual,and Analytical Skills.3.Man-Management Skills and ability to work in a team.4.Adaptability,resilient with good Communication and Organizing Skills.5.Keen to get more Knowledge.

AREA OF INTERESTS 1.Automobile sector 2.Industrial production3.Design sector

4