-
8/17/2019 Msds Sbr Binder
1/3
860 S 19th Street, Richmond, CA 94804 Phone: 510-525-3070
Fax: 510-5 25-4705
Web: www.mtixtl.co m
Ver sion 1 2013-02-07
MATER IAL SAFETY DATA SHEET (MSDS)
SBR Binder for Li-Ion Anode
I. Company and Product Identification
Company: MTI Corporation
860 S. 19th Street, Richmond
CA 94804
Telephone: 510-525-3070
Fax: 510-525-4705
Product: Styrene-Butadiene Rubber (SBR) binder for Li-ion
Battery Anode
Chemical Name: Styr ene-Butadiene Rubber
(SBR)
II. Ingredients / Identity Inf or mation
Major components: Styr ene-Butadiene Rubber (SBR)
III. Physical Pr o per ties
Appearance: Milky white liquid with light blue gloss.
Solidity: 50 +/- 2%
PH: 6-7
Viscosity (NDJ-5S, 25oC): 100~350 mPa. S
Vitrification temperature: -18oC
Storage Temperature: 0~38oC
Odor: Slight typical rubber product odor
Specific Gravity: 1.3-1.6
-
8/17/2019 Msds Sbr Binder
2/3
860 S 19th Street, Richmond, CA 94804 Phone: 510-525-3070
Fax: 510-5 25-4705
Web: www.mtixtl.co m
Ver sion 1 2013-02-07
- 2 -
Boiling Point: N/A Melting
Point: N/A
Decom position Temperature: >250 °C
Va por Pressure: N/A
Percent Volatile: N/A
Solubility in Water: Insoluble
IV. Fire and Explosion Hazard Data
Flash Point: > 300 °C
Lower Ex plosion Limit: N/AUpper
Ex plosion Limit: N/A
Fir e Hazard: Flamma ble /
Com busti ble under high heat and
f lame.
Can generate toxic and com busti ble fumes, -
car bon
monoxide, chlor inated and hydrocarbon
compounds, and
soot.
Fir e Fighting Procedures: Use
full protective equi pment and
SCBA, f ilter masks,
etc. Extinguishing Media:
High ex pansion foam, water fog and
spr ay.
V. Health Hazards
Contact: May cause sk in
irr itation. For prolonged handling, use
protective gloves
and clothing. Wash hands with mild soap after
handling.
Avoid contact with eyes. If the eyes are
irr itated f lush with water for
ten
minutes. O btain medical attention.
Avoid ingestion. If ingested seek
medical attention.
Inhalation: Excessive inhalation can cause
headache, nausea, irr itation. Handle the
product in minimum quantity and work
in well-ventilated ar ea.
VI. Reactivity and Sta bility
Sta bility: Product
is non-r eactive with ali phatic
hydrocarbons and non-polarchemicals.
Do not use in contact with strong acids and
alk aline solutions.
R eactivity: Sta ble under
normal wor k ing and storage
condition. Normally store below
35 °C in coo l, dry location.
VII. Waste Disposal
Disposal must be in accordance
with Feder al, State and
Local R egulations.
Bury waste in approved landfill site.
Do not inciner ate.
-
8/17/2019 Msds Sbr Binder
3/3
860 S 19th Street, Richmond, CA 94804 Phone: 510-525-3070
Fax: 510-5 25-4705
Web: www.mtixtl.co m
Ver sion 1 2013-02-07
- 3 -
VIII. Protective Equi pment
Ventilation: Local and
gener al ventilation is necessary to keep
air
concentr ation below level of
concer n.
Gloves: Leather , Rubber,
R ubber ized Textile Eye Protection:
Chemical Wor k er s’ Goggles
R espir ator y Protection:
NIOSH/MSHA approved r espir ator
a ppro pr iate for ex posur eof
concer n.
Other Equi pment:
A ppro pr iate safety footwear, and
a ppro pr iate clothing to
minimize sk in contact.
IX. Storage and Tr anspor tation
Package product in paper, plastic
f ilm, or box in order to minimize surface
ex posur e.Store in cool, dry,
ventilated ar ea.
X. Inf or mation
With a ppro pr iate commercial pr actices,
the cloth inser t SBR rubber product is safe
to
handle and in storage. For further
inf ormation on the mater ial or
this MSDS contact the
Technical Dir ector at MTI Corporation.
