Name: Shanghai Institute of Quality Inspection and Technical … · 2019. 3. 20. · Standard or Method Note Chemistry Metals1 and alloys ... The scope of the accreditation in Chinese

ISO/IEC 17025 认可证书

No. CNAS L0128

The scope of the accreditation in Chinese remains the definitive version.

第 1 页共 177 页

Name: Shanghai Institute of Quality Inspection and Technical Research

Address: No. 918, Wanrong Road, Shanghai, China

Registration No. CNAS L0128

Accreditation Criteria: ISO/IEC 17025 and relevant requirements of CNAS

Effective Date: 2019-01-28 Expiry Date：2024-10-11

SCHEDULE 3 ACCREDITED TESTING SCOPE

Item/Parameter№ Test Object

№ Item/ ParameterStandard or Method Note

Chemistry

Metals and alloys

1 Carbon and low-Alloy steel 1

C、Si、Mn、P、S、Cr、Ni、W、Mo、V、Al、Ti、Cu、Nb、Co、B、As、Sn

Carbon and low-alloy steel - Determination of multi-element contents - Spark discharge atomic emission spectrometric method (routine method) GB/T 4336-2016 9.2

2 Stainless steel 1

C、Si、Mn、P、S、Cr、Ni、Mo、Al、Cu、W、Ti、Nb、V、Co、B、As、Sn、Pb

Stainless steel -Determination of multi-element contents-Spark discharge atomic emission spectrometric method(Routine method) GB/T 11170-2008 8.3

3 Copper and copper alloys 1Pb、Fe、Bi、Sb、As、Sn、Ni、Zn、

Methods for analysis of copper and copper alloys-The atomic emission spectrometry YS/T 482-2005(2012) 8


No. CNAS L0128


第 2 页共 177 页

№ Test ObjectItem/Parameter

Standard or Method Note№ Item/ Parameter

P、S、Mn、Si、Cr、Al、Mg、Co、Cd

4Aluminum and aluminum alloys|

1

Si、Fe、Cu、Mn、Mg、Cr、Ni、Zn、Ti、V、Pb、Sn、Sb、Bi、Ca、Cd

Optical emission spectrometric analysis method of aluminum and aluminum alloys GB/T 7999-2015 7

Machinery

Reinforcing Steel Bar

1 Hot roller rib bar for ferroconcrete Partial ParametersSteel for the reinforcement of concrete—Part 2:Hot rolled ribbed bars GB/T 1499.2-2007

Except for grain size；Chemical composition only 14 mm in diameter

2Hot roller round bar for ferroconcrete

Partial Parameters Steel for the reinforcement of concrete Part 1:Hot rolled plain bars GB/T 1499.1-2008

Chemical composition only 14 mm in diameter

3Cold rolled ribbed steel wires and bars

Partial Parameters Cold rolled ribbed steel wires and bars GB/T 13788-2008

Except for alternating bending & stress relaxation tests;Chem


No. CNAS L0128


第 3 页共 177 页



ical composition only 14 mm in diameter

Machine tool

1Metal-cutting machine tools(Safety)

1 Safety Metal-cutting machine tools-General safe guarding specification GB 15760-2004

1 Electrical General specifications for metal-cutting machine tools GB/T9061-2006 3.54.6.8

2 numerical control systemGeneral specifications for metal-cutting machine tools GB/T9061-2006 3.64.6.9

3 sound measurement General specifications for metal-cutting machine tools GB/T9061-2006 3.94.6.6

4 operating force General specifications for metal-cutting machine tools GB/T9061-2006 3.94.6.4

5 Hardness General specifications for metal-cutting machine tools GB/T9061-2006 3.10

6 casting quality General specifications for metal-cutting machine tools GB/T9061-2006 3.13.3

7 Temperature rise General specifications for metal-cutting machine tools GB/T9061-2006 4.6.2.1

8 empty distance General specifications for metal-cutting machine tools GB/T9061-2006 4.6.4

9 free-load running power General specifications for metal-cutting machine tools GB/T9061-2006 4.6.7

2

Metal-cutting machine tools(Technical parameter)

10 Machine tool load test General specifications for metal-cutting machine tools GB/T9061-2006 4.7


No. CNAS L0128


第 4 页共 177 页



11 vibration test General specifications for metal-cutting machine tools GB/T9061-2006 4.8.4

12 Stiffness test General specifications for metal-cutting machine tools GB/T9061-2006 4.8.5

1

Electrical equipment of industrial machines - Continuity of the protective bonding circuit test

Electrical Safety of machinery—Electrical equipment of machines—Part 1：General requirements GB 5226.1-2008 20.2

Except for :EMC

2 resistance test Electrical Safety of machinery—Electrical equipment of machines—Part 1：General requirements GB 5226.1-2008 20.3Except for :EMC

3

Metal-cutting machine tools(Electrical test)

3 High-voltage test Electrical Safety of machinery—Electrical equipment of machines—Part 1：General requirements GB 5226.1-2008 20.4

4


1

Electrical equipment of industrial machines - Continuity of the protective bonding circuit test

Electrical equipment of industrial machines - Continuity of the protective bonding circuit test specifications GB/T 24342-2009 4

5


1 resistance testElectrical equipment of industrial machines—Insulation resistance test specifications Electrical equipment of industrial machines—Insulation resistance test specifications GB/T 24343-2009 4

6


1 High-voltage test Electrical equipment of industrial machines - High-voltage test specifications GB/T 24344-2009 4

1 flatness Test code for machine tools--Part 1: Geometric accuracy of machines operating under no-load or finishing conditions GB/T 17421.1-1998 5.3 7

Metal-cutting machine tools(Geometric accuracy) 2 parallelism

Test code for machine tools--Part 1: Geometric accuracy of machines operating under no-load or finishing conditions GB/T 17421.1-1998 5.4


No. CNAS L0128


第 5 页共 177 页



3 equidistant Test code for machine tools--Part 1: Geometric accuracy of machines operating under no-load or finishing conditions GB/T 17421.1-1998 5.4.3

4 axiality Test code for machine tools--Part 1: Geometric accuracy of machines operating under no-load or finishing conditions GB/T 17421.1-1998 5.4.4.2

5 contact ratio Test code for machine tools--Part 1: Geometric accuracy of machines operating under no-load or finishing conditions GB/T 17421.1-1998 5.5

6 squareness Test code for machine tools--Part 1: Geometric accuracy of machines operating under no-load or finishing conditions GB/T 17421.1-1998 5.6

7 runout Test code for machine tools--Part 1: Geometric accuracy of machines operating under no-load or finishing conditions GB/T 17421.1-1998 5.6.1

8 cycle run-out Test code for machine tools--Part 1: Geometric accuracy of machines operating under no-load or finishing conditions GB/T 17421.1-1998 5.6.1

9 axial float Test code for machine tools--Part 1: Geometric accuracy of machines operating under no-load or finishing conditions GB/T 17421.1-1998 5.6.2.

10 roundness Test code for machine tools--Part 1: Geometric accuracy of machines operating under no-load or finishing conditions GB/T 17421.1-1998 6.6

11 cylindricity Test code for machine tools--Part 1: Geometric accuracy of machines operating under no-load or finishing conditions GB/T 17421.1-1998 6.7

1 flatness Test code for machine tools--Part 1: Geometric accuracy of machines operating under no-load or finishing conditions ISO 230-1:2012 5.3

2 parallelism Test code for machine tools--Part 1: Geometric accuracy of machines operating under no-load or finishing conditions ISO 230-1:2012 5.4

3 equidistant Test code for machine tools--Part 1: Geometric accuracy of machines operating under no-load or finishing conditions ISO 230-1:2012 5.4.3

4 axiality Test code for machine tools--Part 1: Geometric accuracy of machines operating under no-load or finishing conditions ISO 230-1:2012 5.4.4.2

5 contact ratio Test code for machine tools--Part 1: Geometric accuracy of machines operating under no-load or finishing conditions ISO 230-1:2012 5.5

8

Metal-cutting machine tools(Geometric accuracy)

6 squareness Test code for machine tools--Part 1: Geometric accuracy of machines operating under no-load or finishing conditions ISO 230-1:2012 5.6


No. CNAS L0128


第 6 页共 177 页



7 runout Test code for machine tools--Part 1: Geometric accuracy of machines operating under no-load or finishing conditions ISO 230-1:2012 5.6.1

8 cycle run-out Test code for machine tools--Part 1: Geometric accuracy of machines operating under no-load or finishing conditions ISO 230-1:2012 5.6.1

9 axial float Test code for machine tools--Part 1: Geometric accuracy of machines operating under no-load or finishing conditions ISO 230-1:2012 5.6.2.

10 roundness Test code for machine tools--Part 1: Geometric accuracy of machines operating under no-load or finishing conditions ISO 230-1:2012 6.6

11 cylindricity Test code for machine tools--Part 1: Geometric accuracy of machines operating under no-load or finishing conditions ISO 230-1:2012 6.7

9

Metal-cutting machine tools(Accuracy of Positioning)

1 positioning accuracy Test code for machine tools-Part 2:Determination of accuracy and repeatability of positioning numerically controlled axes GB/T 17421.2-2016

10


1 positioning accuracy Test code for machine tools-Part 2:Determination of accuracy and repeatability of positioning numerically controlled axes ISO 230-2:2014

11


1 positioning accuracy Statistical examination of exactly working and positioning of machine-tools Fundamentels VDI/DGQ 3441 1977-03

12


1 positioning accuracy Machine tools - Running tests and rigidity tests - General requirements JIS B 6201:1993

13

Metal-cutting machine tools(Circular tests)

1 Circular tests Test code for machine tools-Part4: Circular tests for numerically controlled machine tools GB/T 17421.4-2016


No. CNAS L0128


第 7 页共 177 页



14

Metal-cutting machine tools(Circular tests)

1 Circular tests Test code for machine tools-Part4: Circular tests for numerically controlled machine tools ISO 230-4:2005

15Metal-cutting machine tools(Vibration)

1 vibration Metal-cutting machine tools--Measurement method for vibration GB/T 16768-1997

16 General purpose parallel lathes All parameters Horizontal lathes-Part2:Specifications JB/T 2322.2-2006

17 General purpose parallel lathes All parametersAcceptance conditions for general purpose parallel lathes-Testing of the accuracy GB/T 4020-1997

18

Numerically controlled Instrument lathes

All parameters Numerically controlled instrument lathes-Part2：Specifications JB/T 8326.2-2017

19

Numerically controlled Instrument lathes

All parameters Numerically controlled instrument lathes-Oart1：Accuracy JB/T 8326.1-2017

20

Numerically controlled horizontal turning machines

All parameters Numerically controlled horizontal turning machines and turning centres-Part 1:Specifications JB/T 4368.1-2013(2017)

21


All parametersTest conditions for numerically controlled turning machines and turning centres—Part 1:Geometric test for machines with a horizontal workholding spindle GB/T 16462.1-2007


No. CNAS L0128


第 8 页共 177 页



22


All parameters Safety of machine tools - Small numerically controlled turning machines and turning centres GB 22997-2008

23


All parameters Safety of machine tools - Large numerically controlled turning machines and turning centres GB 22998-2008

24High precision turning machines

All parameters High precision turning machines-Specifications JB/T 7420-1994

25High precision turning machines

All parameters High precision horizontal lathes-Part1：Testing of the accuracy JB/T 8768.1-2011

26Heavy duty horizontal lathes

All parameters Heavy duty horizontal lathes- Part1:Specifications JB/T 3663.1-2006


All parameters CNC heavy duty horizontal lathes-Part2: Specifications JB/T 8325.2-2006


All parameters Test conditions for heavy duty horizontal lathe - Testing of the accuracy GB/T 23569-2009

29 Instrument lathes All parameters Instrument lathes-Part6:Specifications JB/T 4136.6-2017

30 Instrument lathes All parameters Instrument lathes-Part3:Testing of the accuracy JB/T 4136.3-2017


No. CNAS L0128


第 9 页共 177 页



31 Faceplate lathes All parameters Faceplate lathes-Part1: Specifications JB/T 2523.1-2006

32 Faceplate lathes All parameters Faceplate lathes-Part3：Testing of the accuracy JB/T 2523.3-2011

33CNC vertical turning machines

All parameters CNC vertical turning machines-Part 2:Specification JB/T 9934.2-2006

34CNC vertical turning machines

All parametersTest conditions for vertical turning and boring lathes - Testing of the accuracy - Part 1: Single and double column vertical turning and boring lathes GB/T 23582.1-2009

35CNC automatic lathes with sliding head

All parameters CNC sliding headstock automatic lathe -Part 2：Specifications JB/T 10165.2-2015

36CNC automatic lathes with sliding head

All parameters CNC sliding headstock automatic lathe - Part 1：Testing the accuracy JB/T 10165.1-2015

37 Cylindrical grinding All parameters Cylindrical grinding- Part2: Specifications JB/T 7418.2-2015

38 Cylindrical grinding All parametersExternal cylindrical grinding machines-Testing of the Accuracy GB/T 4685-2007

39 Cylindrical grinding All parametersExternal cylindrical grinding machines Part3：High precision machine tools-Testing of the Accuracy JB/T 7418.3-2014

40 Cylindrical grinding All parametersExternal cylindrical grinding machines—Safeguarding specifications GB 24384-2009

41 Crankshaft grinder All parameters Crankshaft grinder-Part 3:Specifications JB/T 2617.3-2017

42

Surface grinding machines with horizontal grinding wheel

All parameters Surface grinding machines with horizontal grinding wheel spindle and reciprocating table-Part 2:Specifications JB/T 3382.2-2014


No. CNAS L0128


第 10 页共 177 页



spindle and reciprocating table

43

Surface grinding machines with horizontal grinding wheel spindle and reciprocating table

All parametersSurface grinding machines with horizontal grinding wheel spindle and reciprocating table—Testing of the accuracy—Part 1:Machines with a table surface length of up to 1600 mm GB/T 4022.1-2007

44

Surface grinding machines with horizontal grinding wheel spindle and reciprocating table

All parameters Surface grinding machines with horizontal grinding wheel spindle and reciprocating table—Safeguarding specifications GB 24385-2009

45

Surface grinding machines with vertical grinding wheel spindle and reciprocating table

All parameters Surface grinding machines with vertical grinding wheel spindle and reciprocating table-Part2: Specifications JB/T 4183.2-2014

46

Surface grinding machines with vertical grinding wheel spindle and reciprocating table

All parameters Surface grinding machines with vertical grinding wheel spindle and reciprocating table-Testing of the accuracy GB/T 6476-2007


No. CNAS L0128


第 11 页共 177 页



47

Optical projection profile grinding machines

All parameters Optical projection profile grinding machines-Part 3:Specifications JB/T 9912.3-2014

48

Surface grinding machines with vertical wheel spindle and rotary table

All parameters Surface grinding machines with vertical wheel spindle and rotary table -Part3:Specifications JB/T 9909.3-2014

49

Surface grinding machines with vertical wheel spindle and rotary table

All parameters Surface grinding machine with vertical spindle and rotary tables-Part2:Testing of the accuracy JB/T 9909.2-2017

50

External cylindrical centreless grinding machines

All parameters External cylindrical centreless grinding machines-Part 2:Specifications JB/T 9905.2-2014

51

External cylindrical centreless grinding machines

All parameters External cylindrical centreless grinding machines—Testing of the accuracy GB/T 4681-2007

52 Grinder for bearing race All parameters Grinder for bearing race- Part3: Specifications JB/T 4071.3-2007

53 Grinder for bearing race All parametersGrinding machines for bearing ring-Part 1: Outer surface grinding machines-Testing of the accuracy JB/T 4071.1-2007

54 Grinder for bearing race All parametersGrinding machines for bearing ring-Part 2: Inner surface grinding machines-Testing of the accuracy JB/T 4071.2-2007


No. CNAS L0128


第 12 页共 177 页



55

Superfinishing machine for groove of bearing inner rings and superfinishing machine for groove of bearing outer rings

All parametersSuperfinishing machine for groove of bearing inner rings and superfinishing machine for groove of bearing outer rings-Part 2:Specifications JB/T 9921.2-2007

56

Superfinishing machine for groove of bearing inner rings and superfinishing machine for groove of bearing outer rings

All parametersSuperfinishing machine for groove of bearing inner rings and superfinishing machine for groove of bearing outer rings-Part1:Testing of the accuracy JB/T 9921.1-2017

57Double disc surface grinding machines

All parameters Double disc surface grinding machines -Part2: Specifications JB/T 9907.2-2014

58Double disc surface grinding machines

All parameters Double disc surface grinding machines --Part 3: Double disc surface grinding machines with vertical spindle --Testing of the accuracy JB/T 9907.3-2014

59CNC bed-type milling machines

All parameters CNC bed-type milling machines-Specifications JB/T 8329-2008

60 CNC bed-type All parameters Test conditions for CNC copying bed-type milling machines-Testing of the


No. CNAS L0128


第 13 页共 177 页



milling machines

accuracy-Part 1:Milling machines with horizontal spindle GB/T 20958.1-2007

61CNC bed-type milling machines

All parameters Test conditions for CNC copying bed-type milling machines-Testing of the accuracy-Part 2:Milling machines with vertical spindle GB/T 20958.2-2007

62

Milling machines with table of variable height

All parameters Milling machines with table of variable height- Part2: Technical conditions JB/T 2800.2-2006

63


All parameters Test conditions for milling machines with table of variable height–Testing of the accuracy-Part2:Machines with horizontal spindle GB/T 3933.2 -2002

64


All parameters Test conditions for milling machines with table of variable height–Testing of the accuracy-Part3:Machines with vertical spindle GB/T 3933.3 -2002

65

Numerically controlled vertical milling machines with table of variable height

All parameters Numerically controlled vertical milling machines with table of variable height-Specifications JB/T 9928.2-1999

66

Numerically controlled vertical milling machines with table of variable height

All parametersTest conditions for CNC milling machines with table of variable height - Testing of accuracy - Part 2: Machines with vertical spindle GB/T 21948.2-2008

67 milling All parameters Test conditions for manually controlled milling machines with table of fixed


No. CNAS L0128


第 14 页共 177 页



machines with table of fixed height

height-Testing of the accuracy –Part1:Machines with horizontal spindle GB/T 3932.1-2006

68

milling machines with table of fixed height

All parametersTest conditions for manually controlled milling machines with table of fixed height-Testing of the accuracy –Part2:Machines with horizontal spindle GB/T 3932.2-2006

69 Machining centres All parameters Machining centres-Safeguarding specification GB 18568-2001

70 Machining centres All parameters Machining centers-Specifications JB/T 8801-2017

71 Machining centres All parametersTest conditions for machining centres —Part1:Geometric tests for machines with horizontal spindle and with accessory heads(horizontal Z axis) GB/T 18400.1-2010

72 Machining centres All parametersTest conditions for machining centers Part2: Geometric test for machines with vertical spindle JB/T 8771.2-1998（2009）

73 Machining centres All parametersTest conditions of machining centres-Part 4: Accuracy and repeatability of positioning of linear and rotary axes GB/T 18400.4-2010

74 Machining centres All parametersTest conditions of machining centres Part 5: Tests for accuracy and repeatability of positioning of work-holding pallets GB/T 18400.5-2010

75 Machining centres All parametersTest conditions of machining centres Part7：Accuracy of finished test piece GB/T 18400.7-2010

76Precision machining centres

All parameters Precision machining centres-Specifications GB/T 21012-2007


All parametersTest conditions for precision machining centres-Part 1: Geometric tests for machines with horizontal spindle and with accessory heads(horizontal Z axis) GB/T 20957.1-2007


No. CNAS L0128


第 15 页共 177 页




All parametersTest conditions for precision machining centres-Part 2: Geometric tests for machines with vertical spindle or universal heads with vertical primary rotary axis(vertical Z axis) GB/T 20957.2-2007


All parameters Test conditions of precision machining centres-Part 4: Accuracy and repeatability of positioning of linear and rotary axes GB/T 20957.4-2007


All parameters Test conditions of precision machining centres-Part 5: Tests for accuracy and repeatability of positioning of work-holding pallets GB/T 20957.5-2007


All parameters Test conditions of precision machining centres-Part 7: Accuracy of a finished test piece GB/T 20957.7-2007

82Drilling machining centres

All parameters Drilling machining centres-Part 2: Specifications JB/T 8648.2-2008

83Drilling machining centres

All parameters Drilling machining centres-Part 1:Testing of the accuracy JB/T 8648.1-2008（2017）

84CNC vertical drilling machines

All parameters CNC vertical drilling machines-Part 2:Specifications JB/T 8357.2-2008（2017）

85CNC vertical drilling machines

All parameters CNC vertical drilling machines-Part 1:Testing of the accuracy JB/T 8357.1-2008

86 Radial drilling machine All parameters Radial drilling machine-Part2:Specifications JB/T 6335.2-2006

87 Radial drilling machine All parameters Radial drilling machines-Testing of the accuracy GB/T 4017-1997

88 NC jig boring machines All parameters NC jig boring machines-Specifications JB/T 7416-2007


No. CNAS L0128


第 16 页共 177 页



89 NC jig boring machines All parameters NC jig boring machines-Accuracy GB/T 14660-1993

90 NC jig boring machines All parameters NC portal-type boring and milling machines-Specification JB/T 6600-2006

91 NC jig boring machines All parametersMachine tools—Test conditions for bridge-type milling machines—Testing of the accuracy—Part 1:Fixed bridge(portal-type) machines GB/T 19362.1-2003

92 NC jig boring machines All parametersMachine tools—Test conditions for bridge-type milling machines—Testing of the accuracy—Part 1:Fixed bridge(portal-type) machines ISO 8636-1：2000

93

Boring and milling machines with horizontal

All parameters Boring and milling machines with horizontal spindle-Part4: Specification JB/T 4241.4-2006

94


All parametersTest conditions for boring and milling machines with horizontal spindle-Testing of the accuracy - Part 1:Machines with fixed column and movable table GB/T 5289.1-2008

95


All parametersTest conditions for boring and milling machines with horizontal spindle-Testing of the accuracy-Part4 :Planer type machines with movable column JB/T 4373-1999

96 Cylinder honing machine All parameters Cylinder honing machine JT/T 125-2007

97 Shaping machines All parameters Shaping machines- Part3: SpecificationsJB/T 3362.3-2006 JB/T 3362.3-2006

98

Slideways grinding machines with two columns

All parameters Slideways grinding machines with two columns-Part 2: Specifications JB/T 10578.2-2014

99 Slideways grinding All parametersSlideways grinding machines with two columns-Testing of the accuracy GB/T 5288-2007


No. CNAS L0128


第 17 页共 177 页



machines with two columns

100

Slideways grinding machines with two columns

All parameters Slideways grinding machines with two columns-Testing of the accuracy ISO 4703:2001

101 Gear hobbing machines All parameters Gear hobbing machines-Part 2:Specifications JB/T 6344.2-2013

102 Gear hobbing machines All parameters Gear hobbing machines- Testing of the accuracy GB/T 8064-1998

103 Gear hobbing machines All parameters Gear hobbing machines- Testing of the accuracy ISO 6545:1992

104 Horizontal band sawing machine All parametersHorizontal band sawing machine-Part 2:Testing of the accuracy JB/T 4318.2-2013

105 Horizontal band sawing machine All parameters Horizontal band sawing machine-Part 3: Specifications JB/T 4318.3-2013

106 Vertical band sawing machine All parametersVertical band sawing machine -Part3：Ordinnary type vertical band sawing machine -Specifications JB/T 9930.3-2015

107 Vertical band sawing machine All parametersVertical band sawing machine -Part2：Ordinnary type vertical band sawing machine -Testing of the accuracy JB/T 9930.2-2015

108 Roll grinding machines All parametersRoll grinding machines-Part 2:Grinding wheel moving style roll grinding machines Specifications JB/T 6340.2-2007

109 Roll grinding machines All parametersRoll grinding machine-Part 3:Grinding machine with wheelhead moving style-Testing of the accuracy JB/T 6340.3-2008

110Metalforming machinery-Safety

Safety Metalforming machinery-Safety requirements GB 17120-2012

111Metalforming machinery (performance)

1 Hardness General specifications for metalforming machine JB/T 1829-2014 3.9


No. CNAS L0128


第 18 页共 177 页



2 operating force General specifications for metalforming machine JB/T 1829-2014 3.2

3 sound General specifications for metalforming machine JB/T 1829-2014 3.4

4 rigidity General specifications for metalforming machine JB/T 1829-2014 3.9

5 Temperature rise General specifications for metalforming machine JB/T 1829-2014 4.9

6 Cleanliness General specifications for metalforming machine JB/T 1829-2014 3.13

7 Electrical General specifications for metalforming machine JB/T 1829-2014 4.13

8 Load test General specifications for metalforming machine JB/T 1829-2014 4.16

1 straightness Test code of accuracy for metalforming machine GB/T 10923-2009 5.3

2 flatness Test code of accuracy for metalforming machine GB/T 10923-2009 5.4

3 parallelism Test code of accuracy for metalforming machine GB/T 10923-2009 5.4.3,5.4.4.2

4 equidistant Test code of accuracy for metalforming machine GB/T 10923-2009 5.5

5 axiality Test code of accuracy for metalforming machine GB/T 10923-2009 5.6

6 contact ratio Test code of accuracy for metalforming machine GB/T 10923-2009 5.6.1

7 squareness Test code of accuracy for metalforming machine GB/T 10923-2009 5.6.1

8 runout Test code of accuracy for metalforming machine GB/T 10923-2009 5.6.2

112Metalforming machinery (accuracy )

9 cycle run-out Test code of accuracy for metalforming machine GB/T 10923-2009 6.6


No. CNAS L0128


第 19 页共 177 页



10 axial float Test code of accuracy for metalforming machine GB/T 10923-2009 6.7

11 roundness Test code of accuracy for metalforming machine GB/T 10923-2009 5.2.3

12 cylindricity Test code of accuracy for metalforming machine GB/T 10923-2009

13 Position accuracy Test code of accuracy for metalforming machine GB/T 10923-2009

113Metalforming machinery (sound )

1 sound Metal forming machinery -sound measurement method of sound pressure levels GB/T 23281-2009

114Metalforming machinery (sound )

1 sound Metal forming machinery - sound measurement method of sound power levels GB/T 23282-2009

115 Open press All parameters Open press-Part 1:Specifications JB/T 6580.1-2014

116 Open press All parameters Mechanical press-Safety requirements GB 27607-2011

117 Open press All parameters Mechanical press–Safety EN 692:2005+A1:2009

118 Open press All parameters Open front mechanical power presses-Testing of the accuracy GB/T 23280-2009

119 Open press All parameters Open double-point press: accuracy JB/T 5199-1991

120 Open press All parameters Open multi working position press: accuracy JB/T 9961-2015

121Bench mechanical power presses

All parameters Bench mechanical power presses-Part1:Specification JB／T 5247.1-2011

122 Bench mechanical All parametersBench mechanical power presses-Part3:Testing of the accuracy JB／T 5247.3-2011


No. CNAS L0128


第 20 页共 177 页



power presses

123Straight-side mechanical power press

All parameters Straight-side mechanical power press-Part 2：Technical requirements JB/T 1647.2-2012(2017)


All parameters Straight-sided four-point mechanical power press-Testing of the accuracy JB/T 5200-2012


All parameters Straight sided single or two-point mechanical power presses-Testing of the accuracy GB/T 10924-2009

126Closed cold extrusion presses

All parameters Closed cold extrusion presses-Specifications JB/T 2936.2-1999

127

High speed precision straight side press

All parameters High speed precision straight side press-Technical requirements JB/T 10168-2015

128Bottom driven double-acting drawing presses

All parameters Bottom driven double-acting drawing presses-Part2:Specifications JB/T 8348.2-2014

129Bottom driven double-acting drawing presses

All parameters Bottom driven double-acting drawing presses-Part 1:Testing of the accuracy JB/T 8348.1-2014

130 Press brakes All parameters Press brakes-Part1:Specifications JB/T 2257.1-2014

131 Press brakes All parameters Hydraulic press brakes-Safety requirements GB 28243-2012

132 Press brakes All parameters Plate and edge bending machines-sound limit JB 9976-1999(2009)


No. CNAS L0128


第 21 页共 177 页



133 Press brakes All parameters Press brakes-Testing of the accuracy GB/T 14349-2011

134 Plate shear All parameters Plate shear-Specifications JB/T 5197.2-2015

135 Plate shear All parameters Shears-Safety requirements GB 28240-2012

136 Plate shear All parameters Bar shearing machines, crocodile shearing machines and plate shearing machines-sound limit JB 9969-1999(2009)

137 Plate shear All parameters Plate shear-Testing of the accuracy GB/T 14404-2011

138high pressure metal diecasting units

All parameters Safety requirements for high pressure metal diecasting units GB 20906-2007

139high pressure metal diecasting units

All parameters Safety of machinery-Safety requirements for pressure metal diecasting units EN 869：2006

140 Hot-chamber die casting machine All parametersHot-chamber diecasting machine -Part 3：Technical requirements JB/T 6309.3-2015

141 Hot-chamber die casting machine All parametersHot-chamber diecasting machine -Part 2：Testing of the accuracy JB/T 6309.2-2015

142CNC pipe bending machines

All parameters CNC pipe bending machines-Specifications JB/T 5761.1-1999


All parameters Pipe bending machines-Specifications JB/T 2671.2-1998


All parameters Tube bending machines-Part 3:Testing of the accuracy JB/T 2671.3-2010

145 Three-roll plate bending All parameters Three-roll plate bending machines-Part2:Specifications JB/T 3185.2-2014


No. CNAS L0128


第 22 页共 177 页



machines

146Three-roll plate bending machines

All parameters Three-roll plate bending machines-Part3:Testing of the accuracy JB/T 3185.3-2014

147 Hydraulic presses All parameters Hydraulic presses-Safety requirements GB 28241-2012

148 Hydraulic presses All parameters Machine Tools- Safety-Hydraulic Presses EN 693：2001

149 Hydraulic presses All parameters Hydraulic presses-Specifications JB/T 3818-2014

150Woodworking machines (Safety )

1 safety Woodworking machines-Safety code GB 12557-2000 GB 12557-2010

1 electrical Woodworking machines-General specifications GB/T 14384-2010Except for :dust density

2 hardness Woodworking machines-General specifications GB/T 14384-2010Except for :dust density

3 temperature Woodworking machines-General specifications GB/T 14384-2010Except for :dust density

4 Rotational speed difference Woodworking machines-General specifications GB/T 14384-2010Except for :dust density

5 Feed difference Woodworking machines-General specifications GB/T 14384-2010Except for :dust density

151Woodworking machines (performance)

6 operating force Woodworking machines-General specifications GB/T 14384-2010 Except for


No. CNAS L0128


第 23 页共 177 页



:dust density

7 sound Woodworking machines-General specifications GB/T 14384-2010Except for :dust density

8 no-load power Woodworking machines-General specifications GB/T 14384-2010Except for :dust density

9 Load test Woodworking machines-General specifications GB/T 14384-2010Except for :dust density

10 Vibration Woodworking machines-General specifications GB/T 14384-2010Except for :dust density

11 Rigidity Woodworking machines-General specifications GB/T 14384-2010Except for :dust density

152Woodworking machines(sound )

1 sound Woodworking machines- Measurement method of sound pressure level JB/T 9953-1999

1 straightness Acceptance code of accuracy for woodworking machines JB/T 4171-1999

2 flatness Acceptance code of accuracy for woodworking machines JB/T 4171-1999

3 parallelism Acceptance code of accuracy for woodworking machines JB/T 4171-1999

4 equidistant Acceptance code of accuracy for woodworking machines JB/T 4171-1999

153Woodworking machines(accuracy)

5 axiality Acceptance code of accuracy for woodworking machines JB/T 4171-1999


No. CNAS L0128


第 24 页共 177 页



6 contact ratio Acceptance code of accuracy for woodworking machines JB/T 4171-1999

7 squareness Acceptance code of accuracy for woodworking machines JB/T 4171-1999

8 runout Acceptance code of accuracy for woodworking machines JB/T 4171-1999

9 cycle run-out Acceptance code of accuracy for woodworking machines JB/T 4171-1999

10 repeatability of positioning accuracy Acceptance code of accuracy for woodworking machines JB/T 4171-1999

11 positioning accuracy Acceptance code of accuracy for woodworking machines JB/T 4171-1999

154Electro-discharge machines

All parameters Electro-discharge machines-Technical requirements for safeguarding GB 13567-1998

155

Wire electrical-discharge machines (Reciprocating traveling type)

All parameters Wire electrical-discharge machines (Reciprocating traveling type)-Technical requirements JB/T 10082-2010

156

Wire electrical-discharge machines (Reciprocating traveling type)

All parameters NC reciprocating traveling type wire electrical-discharge machines -Testing of the accuracy GB/T 7926-2015

157

Wire electrical-discharge machines (Unidirectional travelling type)

partial parameters Wire electrical-discharge machines (Unidirectional travelling type)-Technical requirements JB/T 5544-2012Except for :EMC


No. CNAS L0128


第 25 页共 177 页



158


All parameters Wire electrical-discharge machines (Unidirectional traveling type)-Testing of the accuracy GB/T 19361-2003

159


All parameters Wire electrical-discharge machines (Unidirectional traveling type)-Testing of the accuracy ISO 14137：2000

160Sinking electro-discharge machines

partial parameters Sinking electro-discharge machines-Technical requirements JB/T 4105-2010Except for :EMC

161Sinking electro-discharge machines

All parametersDie sinking electro-discharge machines(EDM)-Testing of the accuracy-Part 1:Single column machines(cross slide type and fixed table type) GB/T 5291.1-2001

162

Mechanical vibration-Balance quality requirements for rotors in a constant(rigid) state

All parametersMechanical vibration-Balance quality requirements for rotors in a constant(rigid) state-Part 1:Specification and verification of balance tolerances GB/T 9239.1-2006

Accredited only for :testing rotor under 500kg (including 500kg)

163 balancing machines Description verification and evaluation of balancing machines GB/T 4201-2006 6

164 Industrial robots-Safety 1 safetyRobot for industrial environments-Safety requirements-Part 1:Robot GB 11291.1-2011

165 Industrial robots-Safety 1 safetyRobots and robotic devices-Safety requirements for industrial robots -Part 1: Robots ISO 10218-1:2011


No. CNAS L0128


第 26 页共 177 页



166 Industrial robots-Safety 1 safety Industrial robots-Safety implementation specification GB/T 20867-2007

167Industrial robots-performance

1 performance Industrial robots-Performance criteria and related test methods GB/T 12642-2013


1 performance Manipulating industrial robots -- Performance criteria and related test methods ISO 9283:1998


1 performance Industrial robot-Detailed implementation specification for performance and related test GB/T 20868-2007


1 performance Industrial robot-Product acceptance implementation specification JB/T 10825-2008

Except for :power adaptability, electromagnetic compatibility, environmental and climatic adaptability, vibration resistance, transportability


1 performance Industrial robot-Acceptance rules JB/T 8896-1999Except for :power adaptabilit


No. CNAS L0128


第 27 页共 177 页



y, electromagnetic compatibility, environmental and climatic adaptability, vibration resistance, transportability

172General specifications of spot

partial parameters General specifications of spot-Welding robots GB/T 14283-2008


173 laser processing robots partial parameters General specifications of laser processing robots GB/T 20722-2006Except for :power


No. CNAS L0128


第 28 页共 177 页



adaptability, electromagnetic compatibility, environmental and climatic adaptability, vibration resistance, transportability

174 arc welding robot partial parameters General specifications of arc welding robots GB/T 20723-2006



No. CNAS L0128


第 29 页共 177 页



175 assembly robots partial parameters General specifications of assembly robots GB/T 26154-2010


176 assembly robots partial parameters General specifications of assembly robots JB/T 5064-1991 5.6，6.7

Except for :power adaptability, electromagnetic compatibility, environmental and climatic adaptability, vibration resistance, transportab


No. CNAS L0128


第 30 页共 177 页



ility

177 transport robots partial parameters General specifications of transport robots JB/T 5063-2014


178 painting robot partial parameters General specifications of spray-painting robot JB/T 9182-2014

Except for :power adaptability, electromagnetic compatibility, environmental and climatic adaptability, vibration


No. CNAS L0128


第 31 页共 177 页



resistance, transportability

179

Flexible manufacturing system of off-line programming robots

partial parameters Flexible manufacturing system of off-line programming robots-Part 1:General requirements GB/T 26153.1-2010


180

Flexible manufacturing system of off-line programming robots

partial parameters Flexible manufacturing system of off-line programming robots-Part 2:Belt grinding manufacturing system GB/T 26153.2-2010

Except for :power adaptability, electromagnetic compatibility, environmental and climatic adaptabilit


No. CNAS L0128


第 32 页共 177 页



y, vibration resistance, transportability

General machinery and equipment

1 Thickness Specification for minimal thickness of the shell of valves GB/T 26640-2011 3、4PN≤40MPa

2 Shell Test Industrial valves-Pressure testing GB/T 13927-2008 5 PN≤40MPa

3 Back seat Test Industrial valves-Pressure testing GB/T 13927-2008 5 PN≤40MPa

4 seat Test Industrial valves-Pressure testing GB/T 13927-2008 5 PN≤40MPa

5 Shell Test Valve inspection and testing GB/T 26480-2011 5.3 PN≤40MPa

6 Back seat Test Valve inspection and testing GB/T 26480-2011 5.3 PN≤40MPa

7 Low pressure seat Test Valve inspection and testing GB/T 26480-2011 5.3PN≤40MPa

8 High pressure seat Test Valve inspection and testing GB/T 26480-2011 5.3PN≤40MPa

9High pressure test of double block and bleed

Valve inspection and testing GB/T 26480-2011 5.3 PN≤40MPa

10 Mark content Industrial valves-marking GB/T 12220-2015 3

11 Mark method Industrial valves-marking GB/T 12220-2015 4

1 Valve

12 Shell Test General requierments for industrial steel valves GB/T 12224-2015 7 PN≤40MP


No. CNAS L0128


第 33 页共 177 页



a

13 seat Test General requierments for industrial steel valves GB/T 12224-2015 7 PN≤40MPa

14 Performance requirement General requirement for: pressure reducing valves GB/T 12244-2006 6

15 Performance requirementMethods of performance test for pressure reducing valves GB/T 12245-2006 6

16 Face-to-face dimensionMetal valves-Face to face,end to end,center to face and ceter to end dimensions GB/T 12221-2005 4

17 Surface quality evalution Valves cast steel visual quality reqrirements JB/T 7927-2014(2017) 3,4,5

18 Shell Test Valve Inspection and Testing API STD 598-2016 6 PN≤40MPa

19 High pressure seat Test Valve Inspection and Testing API STD 598-2016 6PN≤40MPa

20 Low pressure seat Test Valve Inspection and Testing API STD 598-2016 6PN≤40MPa

21 Back seat Test Valve Inspection and Testing API STD 598-2016 6 PN≤40MPa

22 Pressure test Specification for Pipeline and Piping Valves API SPEC 6D CHINESE-2014 9 PN≤40MPa

23flow coefficient and flow resistance coefficient

Valves-Test method of flow coefficient and flow resistance coefficient GB/T 30832-2014 4,5,6,7

PN≤40MPa

2 Flanged iron gate valves All ParametersGeneral purpose industrial valves--Flanged iron gate valves GB/T 12232-2005

PN≤40MPa

3Casting iron globe valves and lift check valves

All Parameters General purpose industrial valves--Casting iron globe valves and lift check valves GB/T 12233-2006PN≤40MPa


No. CNAS L0128


第 34 页共 177 页



4

Bolted bonnet steel gate valves for petroleum and natural gas industries

All Parameters Bolted bonnet steel gate valves for petroleum and natural gas industries GB/T 12234-2007PN≤40MPa

5Steel globe valves and lift check valve

All Parameters Steel globe valves and lift check valve for petroleum,petrochemical and allied industries GB/T 12235-2007PN≤40MPa

6 Steel swing check valve All ParametersSteel swing check valve for petroleum,petrochemical and allied industries GB/T 12236-2008

PN≤40MPa

7

Steel ball valves for petroleum,petrochemical and allied industries

All Parameters Steel ball valves for petroleum,petrochemical and allied industries GB/T 12237-2007PN≤40MPa

8

Flanged and wafer resilient seal butterfly valves

All Parameters Flanged and wafer resilient seal butterfly valves GB/T 12238-2008 PN≤40MPa

9

Diaphragm valves made of metallic materials

All Parameters Industrial valves--Diaphragm valves made of metallic materials GB/T 12239-2008PN≤40MPa

10 Cast iron swing check valves All Parameters Cast iron swing check valves GB/T13932-2016PN≤40MPa

11 Iron plug valves All Parameters Iron plug valves GB/T 12240-2008 PN≤40MPa

12Cast iron and copper alloy ball valves

All Parameters Cast iron and copper alloy ball valves GB/T 8464-2008 PN≤40MPa


No. CNAS L0128


第 35 页共 177 页



13 pipeline valves All Parameters Specification of pipeline valves GB/T 19672-2005 PN≤40MPa

14 Wafer type check valve All Parameters Wafer type check valve JB/T 8937-2010(2017)PN≤40MPa

15 Blow-down valves All Parameters JB/T 6900-1993(2009)PN≤40MPa

16 Hydraulic control valve All Parameters Hydraulic control valve CJ/T 219-2017PN≤40MPa

17 Pilot-operated reducing valves All Parameters Pilot operated pressure reducing valves GB/T 12246-2006PN≤40MPa

18

Resilient-seated gate valves for water supply and drainage service

All Parameters Resilient-seated gate valves for water supply and drainage service CJ/T 216-2013PN≤40MPa

19 Metallic sealing butterfly valve All Parameters Metallic sealing butterfly valve JB/T 8527-2015(2017)PN≤40MPa

20Butterfly valves for water supply and drainage

Part of Parameters Butterfly valves for water supply and drainage CJ/T 261-2015

PN≤40MPa，Except for: sanitation、non-destructive testing

21 Tee strainers for fluids for pipes All Parameters Tee strainers for fluids for pipes GB/T 14382-2008PN≤40MPa

22 Flexible rubber joint All Parameters Flexible rubber joint CJ/T 208-2005PN≤40MPa

23 grooved couplings All Parameters grooved couplings CJ/T 156-2001PN≤40MPa


No. CNAS L0128


第 36 页共 177 页



24

Double check valve backflow prevention assembly

All Parameters Double check valve backflow prevention assembly CJ/T160-2010 PN≤40MPa

25 metallic bellows expansion joints All Parameters General specification of metallic bellows expansion joints GB/T 12777-2008PN≤40MPa

26 Eccentric semi-ball valve Part of Parameters Eccentric semi-ball valve CJ/T 283-2017

PN≤40MPa，Except for: sanitation

27 Eccentric semi-ball valve Part of Parameters Eccentric semi-ball valve GB/T 26146-2010

PN≤40MPa，Except for: non-destructive testing

28 Steel plug valves Part of Parameters Steel plug valvesGB/T 22130-2008 GB/T 22130-2008

PN≤40MPa，Except for: Fire resistance test

29 Metal-seated ball valve Part of Parameters Metal-seated ball valve GB/T 21385-2008

PN≤40MPa，Except for: Fire resistance test

30 Non-slam nozzle check valve Part of Parameters Non-slam nozzle check valve CJ/T 255-2007



No. CNAS L0128


第 37 页共 177 页



31

Resilient-seated gate valves for water supply service

Part of Parameters Resilient-seated gate valves for water supply service GB/T 24924-2010


32 Parallel plane disc gate valves All Parameters Parallel plane disc gate valves GB/T 23300-2009PN≤40MPa

33 Air inbreathe-release valve All ParametersCompound quick air inbreathe-release valve for water supply pipeline CJ/T 217-2013

PN≤40MPa

34 slow closure type check valve All ParametersGeneral specification of slow closure type check valve for water supply and sewerage CJ/T 154-2001

PN≤40MPa

35 Flange All Parameters Pipeline valves, technical delivery conditions JB/T 74-2015(2017) PN≤40MPa

36 Compact steel valves All Parameters Compact steel valves JB/T 7746-2006PN≤40MPa

37 Axial flow check valve All Parameters Axial flow check valve GB/T 21387-2008PN≤40MPa

38

Liner fluoroplatics for flanged and wafer steel butterfly valve

All Parameters Liner fluoroplatics for flanged and wafer steel butterfly valve GB/T 26144-2010PN≤40MPa

39 Drain valve All Parameters Drain valve GB/T 26145-2010 PN≤40MPa

40Pilot control pressure reducing valve

All Parameters Pilot control pressure reducing valve CJ/T 262-2016 PN≤40MPa

41Piping compensatory couplings

Part of Parameters Piping compensatory couplings GB/T 12465-2017

PN≤40MPa，Except for :sanitation


No. CNAS L0128


第 38 页共 177 页



and Fire resistance test

42 corrugated metal hose assemblies Part of Parameters General specification for corrugated metal hose assemblies GB/T 14525-2010

PN≤40MPa，Except for : non-destructive testing

43

Automatic sprink system:Convention valve

All Parameters Automatic sprink system-Part 6:Convention valve GB 5135.6-2018 PN≤40MPa

44 Valves for power station Part of Parameters Valves for power station NB/T 47044-2014

PN≤40MPa，Except for: High temperature，non-destructive testing

45 Hydraulic control valve All Parameters Hydraulic control valve JB/T 10674-2006PN≤40MPa

46 Metal-sealed unfurled valve All Parameters Metal-sealed unfurled valve JB/T 10673-2006PN≤40MPa

47 Bellows sealing steel globe valve Part of Parameters Bellows sealing steel globe valve JB/T 11150—2011

PN≤40MPa，Except for: non-destructive testing

48 Steel gate, globe and check valve Part of ParametersSteel gate, globe and check valve for the petroleum and natural gas industries(for sizes DN100 and smaller) GB/T 28776—2012

PN≤40MPa，Except


No. CNAS L0128


第 39 页共 177 页



for the petroleum and natural gas industries(for sizes DN100 and smaller)

for: High temperature

49 Bellows sealing steel gate valve All Parameters Bellows sealing steel gate valve JB/T 11487-2013(2017)PN≤40MPa

50Slow closure butterfly check valve

All Parameters Slow closure butterfly check valve CJ/T 282-2016 PN≤40MPa

51

Pneumatic industrial process control valves

All Parameters Pneumatic industrial process control valves GB/T 4213-2008 PN≤40MPa

All Parameters Rotodynamic pumps—Hydraulic performance acceptance tests—Grades 1 、2 and 3 GB/T 3216-2016

Accredited only for:Flow0-800m3/hHead≤250mPower≤150kW

1 Flow Rotodynamic pumps—Hydraulic performance acceptance tests—Grades 1 、2 and 3 GB/T 3216-2016 4.4

2 Head Rotodynamic pumps—Hydraulic performance acceptance tests—Grades 1 、2 and 3 GB/T 3216-2016 4.4

52 pump

3 Pump efficiency Rotodynamic pumps—Hydraulic performance acceptance tests—Grades 1 、2 and 3 GB/T 3216-2016 4.4


No. CNAS L0128


第 40 页共 177 页



4 Power Rotodynamic pumps—Hydraulic performance acceptance tests—Grades 1 、2 and 3 GB/T 3216-2016 4.4

5 The spirit eclipse experimentsRotodynamic pumps—Hydraulic performance acceptance tests—Grades 1 、2 and 3 GB/T 3216-2016 5.8

Part of items Submersible pumps GB/T 12785-2014

Accredited only for:Flow0-140m3/hHead≤100mPower≤150kWExcept for ：Test of axial force

1

The electrical engineering settles the son rounds a measurement for to the machine hull insulating electric resistance( measure the cold only)

Submersible pumps GB/T 12785-2014 6

53 Submersible pumps

2

The electrical engineering settles the son rounds a measurement for under the actual and cold direct current electric resistance



No. CNAS L0128


第 41 页共 177 页



3 Bearing the electric voltage experiments Submersible pumps GB/T 12785-2014 14

4

The biggest grain passes the measurement of the ability


5The sum settles the head of the flow bottom


6The sum settles the pump efficiency of the flow bottom


7 The temperature rises to experiment Submersible pumps GB/T 12785-2014 9

8The electrical engineering blocks up to turn to experiment


9

The electric motor gets empty to carry the characteristic measurement


10

The electrical engineering is biggest to turn the measurement


11

The electrical engineering least turns the measurement



No. CNAS L0128


第 42 页共 177 页



12

Pump within the scope of 0.7-1.3 times sums settle the discharge the measurement of the stalk power

Submersible pumps GB/T 12785-2014 10.3.1

13

The measurement of the electrical engineering noise voice


14The measurement of the electrical engineering vibration


15The hot insulates the measurement of the electric resistance

Submersible pumps GB/T 12785-2014 10.3.2

16The full circle pounds at to bear the electric voltage experiments

Submersible pumps GB/T 12785-2014 14.3

All Parameters Tesing methods for screw pumps JB/T 8091-2014


1 running experiment Tesing methods for screw pumps JB/T 8091-2014 4.1

54 screw pumps

2 valve experiment Tesing methods for screw pumps JB/T 8091-2014 4.1


No. CNAS L0128


第 43 页共 177 页



3 performance experiment Tesing methods for screw pumps JB/T 8091-2014 4.1

4 NPSH experiment Tesing methods for screw pumps JB/T 8091-2014 4.1

5 vibration experiment Tesing methods for screw pumps JB/T 8091-2014 4.1

6 noise experiment Tesing methods for screw pumps JB/T 8091-2014 4.1

7 other experiment Tesing methods for screw pumps JB/T 8091-2014 4.1

1 vibration Methods of measuring and evaluating vibration of pumps GB/T 29531-2013 6 55 pump

2 noise Methods of measuring and evaluating noise of pumps GB/T 29529-2013 10

56 centrifugal pumps All Parameters Technical specifications centrifugal pumps-class II GB/T 5656-2008


57 centrifugal pumps All Parameters Technical specifications centrifugal pumps-class III GB/T 5657-2013



No. CNAS L0128


第 44 页共 177 页



58Water submersible motor-pumps

All Parameters Water submersible motor-pumps GB/T 24674-2009


59 Submersible motor-pumps All Parameters Submersible motor-pumps GB/T 25409-2010


60 Diving screw pump All Parameters Diving screw pump JB/T 8645-2011（2017）


61Submersible pumps for deep well

All Parameters Submersible pumps for deep well GB/T 2816-2014

Accredited only for:Flow0-140m3/hHead≤100mPower≤150


No. CNAS L0128


第 45 页共 177 页



kW

62 Long shaft deep well pump All Parameters Long shaft deep well pump GB/T 2816-2014


63Single rank single suction acentric pump

All Parameters Technical specifications centrifugal pumps-class II GB/T 5656-2008


64Plastic centrifugal pumps

All Parameters Plastic centrifugal pumps JB/T 8688-2013（2017）


65 Magnetic force acentric pump All Parameters Technical specifications centrifugal pumps-class II GB/T 5656-2008

Accredited only for:Flow0-800m3/hHead≤250


No. CNAS L0128


第 46 页共 177 页



mPower≤150kW

66 Shield acentric pump All Parameters Technical specifications centrifugal pumps-class II GB/T 5656-2008


67 Hot-water acentric pump All Parameters Technical specifications centrifugal pumps-class I GB/T 16907-2014


68Centrifugal pumps for petrochemical

All Parameters Centrifugal pumps for petroleum petrochemical and natural gas industries GB/T 3215-2007


69 Multi- rank acentric pump All Parameters Technical specifications centrifugal pumps-class I GB/T 16907-2014

Accredited only for:Flow0-800m3/h


No. CNAS L0128


第 47 页共 177 页



Head≤250mPower≤150kW

70 Multi- rank acentric pump All Parameters High pressure boiler feed water pump technology conditions JB/T 8059-2008


71Inline type centrifugal pumps

All Parameters Inline type centrifugal pumps JB/T 6878-2006


72centrifugal pump for fresh water

All Parameters Limited values of energy efficiency and evaluating values of energy conservation of centrifugal pump for fresh water GB 19762-2007


73Miniature centrifugal pump

All Parameters Miniature centrifugal pump JB/T 5415-2013（2017）Accredited only for:Flow0-


No. CNAS L0128


第 48 页共 177 页



800m3/hHead≤250mPower≤150kW

74

The light small single grade centrifugal pump

All Parameters The light small single grade centrifugal pump JB/T 6663-2007


75Irrigation and drainage pumps and pump units

All Parameters agriculture and forestry machinery safety technical requirements tractors and 8 parts: irrigation and drainage pumps and pump units GB 10395.8-2006


76

Compact silent inline deepwell pump water booster equipment for non-negative

All Parameters Compact silent inline deepwell pump water booster equipment for non-negative CJ/T 440-2013

Except for ：Health performance、electromagnetic performance


No. CNAS L0128


第 49 页共 177 页



77

Water supply equipment of low voice additive pipe pressure

All Parameters Water supply equipment of low voice additive pipe pressure CJ/T 444-2014

Except for： Health performance、electromagnetic performance

78

Non-negative pressure water supply equipment for water supply network booster pump station in cities and towns

All Parameters Non-negative pressure water supply equipment for water supply network booster pump station in cities and towns CJ/T 415-2013


79 Vertical mixed flow pumps All Parameters Vertical mixed flow pumps JB/T 10812-2007


80

Non-negative pressure water supply equipment

All Parameters Non-negative pressure water supply equipment CJ/T 265-2016

Except for ：Health performance、


No. CNAS L0128


第 50 页共 177 页



electromagnetic performance

81

Non-negative pressure water supply equipment of integration and intelligence

All Parameters Non-negative pressure water supply equipment of integration and intelligence CJ/T 381-2011


82Additive pipe pressure water supply devices

All Parameters Additive pipe pressure water supply devices CJ/T 254-2014


83

Oil seperating and upgrading integrative equipment

All Parameters Oil seperating and upgrading integrative equipment CJ/T 410-2012

Except for ：

material、water quality performance


No. CNAS L0128


第 51 页共 177 页



84

Non-negative pipe system pressure-increasing water supply equipment

All Parameters Non-negative pipe system pressure-increasing water supply equipment GB/T 26003-2010


85

Technical conditions of sewage-elevating device

All Parameters Technical conditions of sewage-elevating device CJ/T 380-2011

Except for： material performance

86

Tank type non-negative pressure water supply devices

All Parameters Tank type non-negative pressure water supply devices CJ/T 302-2008


87

Grease-water separator for restaurant wastewater

All Parameters Grease-water separator for restaurant wastewater CJ/T 295-2015

Except for： material、water quality performance


No. CNAS L0128


第 52 页共 177 页



88

Steady pressure compensation type non-negative pressure water supply devices

All Parameters Steady pressure compensation type non-negative pressure water supply devices CJ/T 303-2008


89

Variable-frequency governed speed water supply equipment with microcomputer control

All Parameters Variable-frequency governed speed water supply equipment with microcomputer control CJ/T 352-2010

Except for ：Health performance、electromagnetic performance

90 Submersible pumps All ParametersSpecifications for water pump’s small power asynchronous motorsl JB/T 4376-2013(2017)


91 centrifugal pump All Parameters NPSH for centrifugal,mixed flow and axial flow pumps GB/T 13006-2013

Accredited only for:Flow0-800m3/hHead≤250


No. CNAS L0128


第 53 页共 177 页



mPower≤150kW

92 Submersible pumps All Parameters Submersible motor for deep well GB/T 2818-2014


93 centrifugal pump All Parameters Centrifugal pump—Effeciency GB/T 13007-2011


94

Small-size multistage centrifugal pump-Types and basic parameters

All Parameters Small-size multistage centrifugal pump-Types and basic parameters JB/T 6435-2013(2017)


95Waste submersible motor-pumps

1energy efficiency and energy efficiency grades

Minimum allowable values of energy efficiency and energy efficiency grades for waste submersible motor-pumps GB 32031-2015 5


No. CNAS L0128


第 54 页共 177 页



96 Submersible motor-pumps 1energy efficiency and energy efficiency grades

Minimum allowable values of energy efficiency and energy efficiency grades for small-size submersible motor-pumps GB 32029-2015 5

97Submersible pumps for deep well

1energy efficiency and energy efficiency grades

Minimum allowable values of energy efficiency and energy efficiency grades for submersible pumps for deep well GB 32030-2015 5

98 submersible sewage pump All Parameters submersible sewage pump CJ/T 472—2015


All Parameters Safety requirements of displacement air compressor GB 22207-2008

1 temperature control Safety requirements of displacement air compressor GB 22207-2008 4.4

2 oil temperature Safety requirements of displacement air compressor GB 22207-2008 4.4.1.2

3 pressure control Safety requirements of displacement air compressor GB 22207-2008 4.5

4 safety valve sensitivity Safety requirements of displacement air compressor GB 22207-2008 4.5.3.1

5 protective equipment Safety requirements of displacement air compressor GB 22207-2008 4.9

6 pressure vessel Safety requirements of displacement air compressor GB 22207-2008 4.10

99 volume Air compressor

7 electric Safety requirements of displacement air compressor GB 22207-2008 4.14


No. CNAS L0128


第 55 页共 177 页



8 nameplate、sign Safety requirements of displacement air compressor GB 22207-2008 5.2、5.3

All Parameters Displacement compressor-Acceptance tests GB/T 3853-2017

1 suction pressure Displacement compressor-Acceptance tests GB/T 3853-2017 5.2

2 exhaust pressure Displacement compressor-Acceptance tests GB/T 3853-2017 5.2

3 suction temperature Displacement compressor-Acceptance tests GB/T 3853-2017 5.3

4 exhaust pressure Displacement compressor-Acceptance tests GB/T 3853-2017 5.3

5 flow Displacement compressor-Acceptance tests GB/T 3853-2017 5.6

only for air compressor drive by altermating current

6 power Displacement compressor-Acceptance tests GB/T 3853-2017 5.7

7 specific power Displacement compressor-Acceptance tests GB/T 3853-2017 6.9

8 input specific power Displacement compressor-Acceptance tests GB/T 3853-2017 6.9

9 atmospheric pressure Displacement compressor-Acceptance tests GB/T 3853-2017 5.2

10 humidity Displacement compressor-Acceptance tests GB/T 3853-2017 5.4

11 speed Displacement compressor-Acceptance tests GB/T 3853-2017 5.5


12 ambient temperature Displacement compressor-Acceptance tests GB/T 3853-2017 5.3


No. CNAS L0128


第 56 页共 177 页



All Parameters Methods of flow measurement for displacement compressor GB/T 15487-2015

1 volume flow Methods of flow measurement for displacement compressor GB/T 15487-2015 8

only for air compressor drive by altermating current

2 nozzle temperature Methods of flow measurement for displacement compressor GB/T 15487-2015 8.3.2


3 nozzle pressure differenceMethods of flow measurement for displacement compressor GB/T 15487-2015 8.3.1

All Parameters Determinatian of sound level for noise emitted by displacement compressors GB/T 4980-2003 102 volume Air compressor 1 sound power level Determinatian of sound level for noise emitted by displacement compressors GB/T 4980-2003 5.2

All Parameters Measurement and evaluation of mechanical vibration of displacement compressor GB/T 7777-2003 103 volume Air compressor 1 vibration intensity Measurement and evaluation of mechanical vibration of displacement compressor GB/T 7777-2003 5

104 volume Air compressor All ParametersMinimum allowable values of energy efficiency and energy efficiency grades for displacement air compressors GB 19153-2009

105

Oil injected single screw air compressor for general use

All Parameters Oil injected single screw air compressor for general use GB/T 26967-2011

106

Stationary Reciprocating piston air compressor

All Parameters Stationary Reciprocating piston air compressor for general use GB/T 13279-2015


No. CNAS L0128


第 57 页共 177 页



107Reciprocating piston minitype air compressor

All Parameters Reciprocating piston minitype air compressor GB/T 13928-2015

108

Oil-free reciprocating piston air compressor

All Parameters Oil-free reciprocating piston air compressor JB/T 8933-2008

109

Direct drive portable reciprocating pistion air compessor

All Parameters Direct drive portable reciprocating pistion air compessor JB/T 8934-2014

110

Oil injected screw air compressor for general use

All Parameters Oil injected screw air compressor for general use JB/T 6430-2014

111

Conversion frequency oil-flooded screw air compressor

All Parameters Conversion frequency oil-flooded screw air compressor for general use JB/T 10972-2010

112 dry screw air compressor All Parameters Specifications for general use dry screw air compressor JB/T 10598-2006

113water injected single screw air compressor

All Parameters water injected single screw air compressor for general use JB/T 11882-2014

114Oil flooded sliding vane air compressor

All Parameters Oil flooded sliding vane air compressor for general use JB/T 4253-2013

115 refrigeration compressed air All Parameters refrigeration compressed air dryers for general use JB/T 10526-2005


No. CNAS L0128


第 58 页共 177 页

Documents

Name: Shanghai Institute of Quality Inspection and Technical … · 2019. 3. 20. · Standard or Method Note Chemistry Metals1 and alloys ... The scope of the accreditation in Chinese