-1-

Contents

1. Introduction 2

2. Battery Precautions 3

3. Getting Started 4

4. Installation Operation 5

5. Cable Connection 6

6.True Wireless Operation 6

7. NFC Connection 8

8. Button Function 9 10. LED Display Status 1011. Battery Charging 1012. Product Care 11

Please read the following safety warnings and precautions before using your device.

-2-

SpecificationsNanobeat True Wireless BluetoothOutput Power: 12W x 2 S/N: >85dBFrequency range: 50Hz-20KHzPower supply: Lithium battery or USB cableAudio source: iPhone, iPad, Smartphone, Notebook, MP3, MP4, etc Function spec: Bluetooth, Microphone, Line-inSize: ø55mm H73mm

Rechargeable battery with charging option from USB cable Operating rang up to 10 meters

1. Introduction Thank you for purchasing Nanobeat True Wireless stereo, a pair of portable music players, speakers and amplifiers. It can turn any hard surface such as a wooden desk or glass table into big a speaker. This device can be easily connected with smartphone, tablet PC and other devices via Bluetooth or audio cable during your travel and daily life.

-3-

2. Battery Precautions The device can be powered by a built-in rechargeable lithium battery. Please charge the battery for at least 8 hours before your first use of device.To avoid damage to your device, please.

If the device is not used for a long period of time, the battery may be out of power. Please charge the battery.Rechargeable batteries are only to be charged under adult supervision.Use only the supplied micro USB cable to recharge the battery. Improper charging may damage the battery and the device. There are no serviceable parts inside.Should a battery leak, the device may become damaged. Clean the battery compartment immediately, avoiding contact with your skin. Keep the battery out of reach of children. If swallowed, consult a physician immediately.Avoid storing the battery in extremely hot or cold environment. A device with a hot or cold battery may not work temporarily, even when the battery is fully charged.Do not dispose batteries in a fire as they may explode. Batteries may also explode if damaged. Please dispose them according to local regulation. Do not dispose them as household waste.

-4-

3. Getting Started

General controls

LED Microphone

USB port Switch

Volume up NextPlay/Pause/Make/Answer/End a call

Previous Volume

-5-

Down

-6-

4. Installation Operation Rubber stand

Remove the protective tape at the bottom of the device to reveal the rubber stand.Note:1. Don’t throw away the protective tape, please stick it on when using a mounting socket or when you do not use it.2. Clean dust on the pad by wet cloth.

Flat and hard surface

-7-

5. Cable ConnectionPower &Audio Input & Cable

for audio input from computer and power

for audio input from cellphone

6. True Wireless Operation Pairing Nanobeat True Wireless to your smartphone (smartphone should be away from your speaker within 10 meters)

A. Single speaker connection instruction：1. Slide “ON/OFF/BT” switch to BT, you will hear the power-on

indicating sound and quick beeps. Press and hold until you hear two ticks, then your speaker is ready for paring.

2. Select “Search” or “Discover” devices.

3. Select “True Wireless Stereo” and pair with it, you will hear an indicating sound that means a successful pairing with your phone

4. If requested type the password 0000.5. Press the enter key.

-8-

B. A pair of speakers connection instruction：1. For the first time, slide “ON/OFF/BT” to “BT” of both speakers, you

will hear the power-on indicating sounds and three quick beeps respectively.

2. Press the two speakers’ button and hold at the same time until you hear three ticks, the speakers will be in pairing mode for each other (The connection will be done around 20 seconds).

3. Choose either of the two speakers, press button and hold until you hear two ticks, then the speaker is ready for pairing with other Bluetooth device (smartphone, tablet PC ect.).

4. Select “True Wireless Stereo” and pair with it, please follow up section A.

C. The two speakers paired before：1. Turn on the two speakers by sliding the “ON/OFF/BT” to “BT”

respectively, and the two speakers will be automatically connected with an indicating sound.

2. Set the Bluetooth on your smartphone, click the previous pairing,record “True Wireless Stereo”, you will hear an indicating tone around 5 seconds and your phone shows the device is connected around.

Notice:1. The one connected with your smartphone is the master for the left

channel, the other is the slave for the right channel. Only the master speaker can redial the call (subject to the last number in call history) by press and hold around 3 seconds.

-9-

2. If your smartphone shows the device is connected, but no sound when you play music or you can’t dial a phone number when you long press , turn the smartphone Bluetooth off and turn on again, press “True Wireless Stereo” record, reconnecting by hand hearing a sound indicating connection succeeded, then play music or dial the call.

7. NFC Connection NFC: Near Field Communication, is a set of standards for smartphone and this speaker to establish Bluetooth radio communication with each other by touching them together or bringing them into close proximity, usually no more than a few centimeters.Please activate the NFC function

(subjects to tablets own setting) of your Bluetooth device. Choose either of the two speakers, press button and hold until you hear two ticks, bring your Bluetooth device close to speaker, as above picture.Your Bluetooth device will ask you whether you need to pair the speaker. confirm by “Yes” or “OK”, then the pairing process is completed.

-10-

8. Button Function

Play music from your phone

Adjusting sound volumeLong press V-/ or /V+

Playing music from phoneTo start playback, press

To pause playback, press again to resume.

To skip to previous or next song, press V-/ or /V+.

Make a callLong press when you make a call from your mobile phone, the call will (subject to phone settings) automatically transfer to your Nanobeat .

Answer / End a callPress to answer a call, after calling, press again to end a call

-11-

9. LED Display Status

LED Display Light indication

Green Light

Flash slowly In Pairing mode

Stay solid PairedFlash quickly Low battery

Red Light

Stay solid Charging in progressOFF Fully charged

10. Battery Charging

The device has a built-in rechargeable lithium battery. This can be charged by connection to the USB port of your computer. After charging, the device can be used without power connection. Charge the device again when you see the red light blinking quickly.

-12-

11. Product Care

Your device is designed to be light, compact and durable. As an electron- ic device, it must be treated carefully. Putting unnecessary pressure on it or striking the device against other objects can cause damage. To avoid damage to your device, please,

Do not drop, crush, or apply excessive force to the device.Do not expose your device to moisture, extreme or prolonged heat, cold, humidity, or other adverse conditions. Avoid storing it in damp, humid or wet places. It is not waterproof.Do not operate or store unit at places with frequent static electricity or electrical noise (eg. speaker, TV set).Clean the unit with a soft cloth or damp chamois leather, Never use solvents.The unit can only be opened by qualified personnel.This device contains magnets. Keep magnetic field sensitive products such as credit cards and video screen away from this device to avoid damage or malfunction.