作成承認印 配布許可印

Copyright ｃ 2004 by Nikon Corporation.

All Rights Reserved.

無断転載を禁ず!!

Printed in Japan May 2004

VAA30001-R.3636.A

REPAIR MANUAL

VAA30001

VAA30001-R.3636.A

- E4100 -

SPECIFICATIONS ･･･････････････････････････････････････････････････････････････････Ｍ１－Ｍ２

DISASSEMBLING

WARNING ･･･････････････････････････････････････････････････････････････････････････Ｄ１

Rear cover ･･････････････････････････････････････････････････････････････････････Ｄ２－Ｄ３

Discharge Main condenser････････････････････････････････････････････････････････････････Ｄ４

Front cover ････････････････････････････････････････････････････････････････････････････Ｄ５

Battery cover / Battery terminal････････････････････････････････････････････････････････････Ｄ６

Battery holder / Battery terminal / Control release ･････････････････････････････････････････････Ｄ６

LCD ･････････････････････････････････････････････････････････････････････････････････Ｄ７

Holder monitor･････････････････････････････････････････････････････････････････････････Ｄ７

Spring plate A ･････････････････････････････････････････････････････････････････････････Ｄ７

Holder microphone ･････････････････････････････････････････････････････････････････････Ｄ７

Holder flash ･･･････････････････････････････････････････････････････････････････････････Ｄ７

CP1-PCB / TB1-PCB / CCD ･･････････････････････････････････････････････････････････････Ｄ８

Finder unit ････････････････････････････････････････････････････････････････････････････Ｄ９

Separate Zoom motor unit ･･････････････････････････････････････････････････････････････Ｄ１０

Disassemble Zoom motor unit･･･････････････････････････････････････････････････････････Ｄ１１

Separate Lens-barrel ･･････････････････････････････････････････････････････････････････Ｄ１２

Shutter ･････････････････････････････････････････････････････････････････････Ｄ１３－Ｄ１４

Straight tube (1st lens frame) / key tube ･･･････････････････････････････････････････････････Ｄ１５

3rd lens unit / Zoom motor unit ･･････････････････････････････････････････････････････････Ｄ１６

ASSEMBLY

Barrier unit････････････････････････････････････････････････････････････････････････････Ａ１

Straight tube (1st lens frame) / key tube ･････････････････････････････････････････････････････Ａ２

Shutter ･････････････････････････････････････････････････････････････････････････Ａ３－Ａ４

3rd lens unit ･･･････････････････････････････････････････････････････････････････････････Ａ５

Assemble Lens-barrel / CCD base ････････････････････････････････････････････････････Ａ６－Ａ７

Assemble Zoom motor unit ･････････････････････････････････････････････････････････Ａ８－Ａ９

Install Zoom motor unit ････････････････････････････････････････････････････････････････Ａ１０

Finder unit ･･････････････････････････････････････････････････････････････････････････Ａ１１

CCD / TB1-PCB / CP1 -PCB ･･･････････････････････････････････････････････････････････Ａ１２

Holder flash ･････････････････････････････････････････････････････････････････････････Ａ１３

Holder microphone ･･･････････････････････････････････････････････････････････････････Ａ１３

Spring plate A ･･･････････････････････････････････････････････････････････････････････Ａ１３

Holder monitor･･･････････････････････････････････････････････････････････････････････Ａ１３

LCD ･･･････････････････････････････････････････････････････････････････････････････Ａ１３

Arrange wires of Holder flash ･･･････････････････････････････････････････････････････････Ａ１４

Arrange wires of Holder microphone ･････････････････････････････････････････････････････Ａ１４

Arrange LCD wires ･･･････････････････････････････････････････････････････････････････Ａ１５

CONTENTS

VAA30001-R.3636.A

- E4100 -

Battery cover ････････････････････････････････････････････････････････････････････････Ａ１６

Control release / Battery holder ･･････････････････････････････････････････････････Ａ１６－Ａ１７

Front cover ･･････････････････････････････････････････････････････････････････････････Ａ１８

Rear cover ･･････････････････････････････････････････････････････････････････････････Ａ１９

ADJUSTMENT ･････････････････････････････････････････････････････････････････Ａ２０－Ａ２７

DISCRIPTION OF CIRCUIT･･･････････････････････････････････････････････････････････Ｅ１－Ｅ８

ELECTRICITY

OVERALL WIRING ････････････････････････････････････････････････････････････････････Ｅ９

OVERALL BLOCK DIAGRAM ････････････････････････････････････････････････････････････････Ｅ１０

ASIC BLOCK DIAGRAM ･･･････････････････････････････････････････････････････････････Ｅ１１

CCD BLOCK DIAGRAM ･･･････････････････････････････････････････････････････････････Ｅ１２

LENS DRIVE BLOCK DIAGRAM ･･････････････････････････････････････････････････････Ｅ１３

POWER BLOCK DIAGRAM･････････････････････････････････････････････････････････････Ｅ１４

SYSTEM BLOCK DIAGRAM････････････････････････････････････････････････････････････Ｅ１５

PWA CIRCUIT DIAGRAM (STROBE CIRCUIT DIAGRAM) ･･････････････････････････････････Ｅ１６

FUSE ARRANGEMENT (CP1 PCB) ･････････････････････････････････････････････････････Ｅ１７

　　

INSPECTION STANDARD････････････････････････････････････････････････････････････Ｒ１－Ｒ７

TOOL LIST ････････････････････････････････････････････････････････････････････････Ｔ１－Ｔ３

VAA30001-R.3636.A

- M1･ E4100 -

Type E4100 digital camera

Effective pixels 4.0 mega-pixels

CCD 1/2.5-inch high-density CCD; total pixels: 4.23 mega-pixels

Image size (pixels) 2288×1712, 2048×1536, 1600×1200, 1024×768 and 640×480

Lens 3×Zoom Nikkorf = 5.8 to 17.4mm (38 ~ 105mm by conversion with 35mm-format)　F2.8 ~ F4.9

Digital zoom Max. 4.0× (35-mm [135] camera-format equivalent: 460 mm)

Auto focus (AF) Contrast AF

Focus range measured from lens

30 cm (1’～∞ ) - ∞ ; macro mode 4 cm/1.6”(W) - ∞

AF area Automatically selected from 5 places when the scene mode with the center/assist function is selected.

Finder Real image type zoom finder, field of viewfinder: Approx. 80%

Monitor 1.6”, 80,000-dot, amorphous silicon TFT LCD monitor

StorageMediaFile system

File format

Internal memory (14.5 MB)/SD memory cardsCompliant with Design rule for Camera File systems (DCF), Exif 2.21, Digital Print-Order Format (DPOF)Compressed: Compliant with JPEGMovies: QuickTime Motion JPEG

Metering 256-segment matrix metering linked to AF area(when frame is displayed in frame-assisted scene mode)

Exposure control Programmed auto, exposure compensation (–2.0 ~ +2.0 EV in steps of 1/3 EV)

Range(ISO equivalent)

W: EV 1 to 17.8T: EV 2.6 to 16.2

Shutter Mechanical and charge-coupled electronic shutter

Shutter Speed 4-1/3000 sec.

ApertureRange

Electronically controlled open-selectable aperture, control steps: 2 (f/2.8 and f/5.6 [W])

Sensitivity Approximately equivalent to ISO 50 (auto gain of two to four times) (up to equivalent of ISO200)

Self-timer Ten-second duration

SPECIFICATIONS

VAA30001-R.3636.A

- M2･ E4100 -

Built-in SpeedlightRange

Sync method

Equipped with automatic pop-upW: 0.4 to 3.4 m (1.3 to 11.2 ft.)T: 0.4 to 2.0 m (1.3 to 6.6 ft.)Automatic sync control

Interface USB

Video output User can choose from NTSC and PAL

I/O terminals DC input terminal, AV output terminal which is also used as USB terminal

Power sources Two rechargeable Nikon EN-MH1 NiMH batteries, One CR-V3 lithium battery,

Two LR6 (AA) alkaline batteries, . Two ZR6 (AA) nickel manganese batteries,

Two FR6/L91 (AA) lithium batteries, EH-62B AC adapter

Number of frames taken in succession

110 frames (alkaline batteries)/260 frames (EN-MH1)/530 frames (CR-V3)

Dimensions(W×H×D)

88×65×38 mm (3.5” × 2.6” × 1.5”)

Weight Approximately 140 g without battery and memory card

Operating environmentTemperatureHumidity

0 - 40°C (32 – 104°F)Under 85% (no dew condensation)

VAA30001-R.3636.A

- D1･ E4100 -

Disassembly

Note : ① Be sure to remove the SD memory card and batteries before disassembly. ② When disassembling, make sure to memorize the processing state of wires,

screws to be fixed and their types, etc. ③ Because electrical parts are easily damaged by static electricity, make sure

that you are well earthed/grounded.

・Lead-free solder is used for this product.・For soldering work, the special solder and soldering iron are required.・Do NOT mix up lead-free solder with traditional solder.・Use the special soldering iron respectively for lead-free solder and lead solder.

They cannot be used in common.

VAA30001-R.3636.A

- D2･ E4100 -

Rear cover

・ Open the cover (① ).

・ Take out 2 screws (② : M1.7× 5).

・ Take out 2 screws (③ : M1.7× 4.5).

・ Take out 2 screws (④ : M1.7× 4).・ Open the SD card cover side of the rear cover and unhook it as pushing its top by your finger. (Fig. 1)

・ Uncover the rear cover by pulling it slowly backwards, and detach the FPC (⑤ ) from the connector. (Fig. 2)

・ The shaft strap (⑥ ) comes off.

①

②

③

④

⑤

⑥

Rear cover

VAA30001-R.3636.A

- D3･ E4100 -

FPC⑤

(Fig 2)

(Fig 1)

Rear cover

SD card cover

Push.

Push.Push.

VAA30001-R.3636.A

- D4･ E4100 -

Discharge Main condenser

2KΩ/5W

VAA30001-R.3636.A

- D5･ E4100 -

Front cover

・ Remove the lead wire (black:① ) and lead wire (red:② ).・ Remove the FPC (③ ).・ Take out 3 screws (④ : M1.7× 4).・ Remove the front cover by pulling it forwards.・ The stand (tripod:⑤ ) comes off.

Front cover

③

①②

⑤

④

⑤

①

②

VAA30001-R.3636.A

- D6･ E4100 -

・ Take out 2 screws (① : M1.7× 2.5), and remove the battery terminal (② ).

・ The battery cap (③ ), battery terminal (④ ) and battery knob (⑤ ) come off.

・ Remove the battery cover shaft (⑥ ) and uncover the battery cover.

Battery cover / Battery terminal

・ Take out 2 screws (⑦ : M1.7× 3), and remove the battery holder.

・ Take out 2 screws (⑧ : M1.7× 2.5).

・ Remove the lead wire (black: ⑨ ) and detach the terminal (⑩ ).

・ Remove the lead wire (red: ⑪ ) and detach the terminal (⑫ ).

・ Take out 2 screws (⑬ : M1.7× 3) and remove the control release.

Battery holder / Battery terminal / Control release

②

④⑤

Front cover

Battery holder

Battery cover

③

①

⑩

⑦

⑧

⑨

Control release

⑪

⑫

⑥

⑬

VAA30001-R.3636.A

- D7･ E4100 -

LCD

・ Remove the FPC (① ).

・ Remove the lead wires (white:② and red:③ ). (Fig. 1)

・ Remove the LCD.

Holder monitor

・ Take out 2 screws (④ : M1.7× 4).

・ Take out the screw (⑤ : M1.7× 2.5).

・ The holder monitor comes off.

Spring plate A

・ Take out the screw (⑥ : M1.7× 3).

・ The spring plate A comes off.

Holder microphone

・ Remove the lead wires (red: ⑦ and black: ⑧ ).

・ Remove the lead wires (white: ⑨ and black ⑩ ).

・ The holder microphone comes off.

Holder flash

・ Take out the screw (⑪ : M1.7× 4).

・ Remove the lead wires (black:⑫ , gray:⑬ and red:⑭ ).

・ The holder flash comes off.

(Fig.1)②　③

⑫⑬⑭

⑦⑧⑨⑩

Spring plate A

⑤

⑥

LCDHolder microphone

Holder flash

④

①

Holder monitor

⑪

②③

VAA30001-R.3636.A

- D8･ E4100 -

CP1-PCB / TB1-PCB / CCD

・ Take out the screw (① : M1.7× 3).・ Remove the FPC (② ).・ Take out 2 screws (③ : M1.7× 6).・ The lens assembly comes off.・ The spacer (④ ), LPF (⑤ ) and spacer (⑥ ) come off.・ Remove the lead wires (gray:⑦ and white:⑧ ).・ Remove the spacer LCD flex (⑨ ).・ Take out the screw (⑩ : M1.7× 3).・ Remove the holder AF (⑪ ).・ TB1-PCB comes off.・ Unsolder the CCD (⑫ ) and disassemble the CCD and CP1-PCB.

⑫⑥

③

①

⑤

④

⑨

⑦⑧

⑪

⑩

②

CP1-PCB

Lens assembly

TB1-PCB

VAA30001-R.3636.A

- D9･ E4100 -

Finder unit

・ Take out 2 screws (① ).

・ Remove the finder unit by lifting it in the direction indicated by the arrow.

①

Lens-barrel

Finder unit

Note : All of the FFD adjustment tools are not prepared yet. The lens-barrel can be

disassembled and assembled. However, each of the 1st, 2nd and 3rd lens group units

(lens) cannot be replaced with a new one.

VAA30001-R.3636.A

- D10 ･ E4100 -

Separate Zoom motor unit.

・ Unsolder the FPC unit.

・ Take out the screw (① : M1.4 × 2.5).

・ Remove the photo interrupter FPC.

・ Take out the screw (② : M1.4 × 4.2).

・ Take out the 2 screws (③ : M1.4 × 3.5).

・ The zoom motor unit comes off.

③

Photo interrupter

Zoom motor unit ①

②

VAA30001-R.3636.A

- D11 ･ E4100 -

① ②③

Hook

④

⑤

⑥

⑦⑧

Gear shaft plate

Motor

⑪

⑨

⑩

⑧

Gear shaft plate

Disassemble Zoom motor unit.

・ Take out the screw (① : M1.4 × 2.5). ・ Take out the screw (② : M1.4 × 4).

・ Unhook and remove the cover ③ .

・ Remove the gears ( ④ and ⑤ ) and remove the

shafts (⑥ and ⑦ ).

・ Take out the screw (⑧ : M1.4 × 2.5).

・ Remove the gear shaft plate.

・ Remove the gear (⑨ ) and remove the shaft (⑩ ).

・ Take out the 2 screws (⑪ : M1.4 × 1.8).

・ The motor comes off.

VAA30001-R.3636.A

- D12 ･ E4100 -

・ Detach the lens barrel by moving it slowly in the direction indicated by the arrow.

The finder gear A and B come off at the same time.

・ Remove the gear shaft.

Separate Lens-barrel

・ Remove the solder of the shutter FPC and take out the screw (①：M1.4× 2).

・ Take out 3 screws (②：M1.4× 3.5).

・ Remove the shutter FPC from the CCD base.

②

②

①

Remove it from the boss. (It is adhered.)

CCD base

Shutter FPC

Gear shaftShutter FPC

Lens-barrel

Finder gear B

Finder gear A

VAA30001-R.3636.A

- D13 ･ E4100 -

・ Remove the barrier joint plate by pulling it in the direction of A.

Shutter

・ Rotate the turning tube in the direction indicated by the arrow, to extend the lens-barrel to the maximum.

Turning tube

Ａ①

②

Barrier joint plate

【Side view】

ＡＡ

Barrier joint plate

VAA30001-R.3636.A

- D14 ･ E4100 -

・ Take out 2 screws (①：M1.4× 3.5) to separate the 2nd lens frame from the shutter.

・ Rotate the turning tube to the full up position, to reduce the lens-barrel size.

・ Remove the shutter unit by lifting it in the direction of the arrow.

①

Shutter

2nd lens frame

Turning tube

Shutter unit

Note : The 2nd lens group unit (frame) cannot be replaced with a new one.

VAA30001-R.3636.A

- D15 ･ E4100 -

Note : The 1st lens group unit (frame) cannot be replaced with a new one.

・ Remove the turning tube unit from the lens-barrel cover.

・ Remove the straight tube (1st lens frame) by pulling it backwards.

・ Remove the key tube backwards. (It is a little difficult to remove the key tube because it is fixed with hooks.)

Note : The key tube can be easily damaged. Perform its removal carefully.

Straight tube (1st lens frame) / key tube

Barrier unit

・ Remove the name plate.

・ Remove the barrier by turning it slightly in the direction indicated by the arrow.

・ Detach the spring to remove the barrier ring.

Turning tube unit

Lens-barrel cover

Barrier ring

Name plate

Barrier

Spring

Hook

Hook

Straight tube (1st lens frame)

Key tube

Turning tube

VAA30001-R.3636.A

- D16 ･ E4100 -

Note : The 3rd lens group unit (frame) cannot be replaced with a new one.

・ Remove the 3rd lens spring.

・ Turn the focus motor shaft counterclockwise with a flathead screw driver, and remove the 3rd lens unit and

turning stopper.

3rd lens unit / Zoom motor unit

Focus motor3rd lens unit

Turning stopper

3rd lens spring

VAA30001-R.3636.A

- A1･ E4100 -

AssemblyBarrier unit

・ Attach the barrier ring to the straight tube (1st lens frame), and hook the spring.

・ Attach the barrier by turning it slightly in the direction indicated by the arrow.

・ Attach the name plate.

Barrier ring

Name plate

Barrier

Spring

Straight tube (1st lens frame)

VAA30001-R.3636.A

- A2･ E4100 -

Finished unit

・ Align Section A with Section B and push in the key tube by turning counterclockwise.

・ Turn the key tube clockwise until it contacts with the stopper.

・ Align Section D of the 1st lens frame with Section C of the turning tube and assemble them.

Straight tube (1st lens frame) / key tube

Section A

Section B

Turning tube

Light-shielding ring

Key tube

Section A

Section D

Section C

Straight tube (1st lens frame)

Key tube

Lens-barrel cover

Turning tube unit

・ Assemble the turning tube unit into the lens-barrel cover.

VAA30001-R.3636.A

- A3･ E4100 -

Shutter

・ Assemble the shutter unit into the turning tube by following the above direction of the arrow.

・ Assemble the shutter and 2nd lens frame with 2 screws (①：M1.4× 3.5).

①

Shutter

2nd lens frame

Lens-barrel cover

Shutter unit

VAA30001-R.3636.A

- A4･ E4100 -

・ Attach the barrier joint plate by pressing slightly in the direction of A arrow.

【Side view】

・ Rotate the turning tube in the direction indicated by the arrow, to extend the lens-barrel to the maximum.

Barrier joint plate

Turning tube

・ Rotate the turning tube in the direction indicted by the arrow, to reduce the lens-barrel size.

Ａ①

②

Barrier joint plate

ＡＡ

Barrier joint plate

VAA30001-R.3636.A

- A5･ E4100 -

3rd lens unit

・ Hook the 3rd lens spring.

・ Apply the Screw lock (colorless) on both hooking ends of the 3rd lens spring.

・ While turning the focus motor shaft clockwise with a flathead screwdriver, assemble the 3rd lens unit and the

turning stopper into the CCD base.

・ Turn the focus motor shaft further until the 3rd lens unit slightly touches the bottom, then give it about one turn

counterclockwise.

Adhesive: Screw lock

(Colorless)

HH201002

Focus motor3rd lens unit

Turning stopper

3rd lens spring

VAA30001-R.3636.A

- A6･ E4100 -

・ Attach the gear A to the CCD base.

・ Attach the finder gear B to the CCD base.

・ Pass the shutter FPC through the hole of the CCD base, and assemble the lens-barrel.

・ Set the finder gear C and insert the gear shaft.

・ Apply the cemedine 575 on the tip of the gear shaft from the rear surface of the CCD base.

・ Apply the cemedine 575 on the tip of the gear shaft.

Assemble Lens-barrel / CCD base

Finder gear CAdhesive:

Cemedine 575　　

J67017

Tip of gear shaft

CCD base

Adhesive:

Cemedine 575　　

J67017

Gear A(This surface must be at the lens-barrel side.)

Shutter FPC

Lens-barrel

CCD base

Finder gear C

Finder gear B(This surface must be at the lens-barrel side.)

VAA30001-R.3636.A

- A7･ E4100 -

・ Tighten the 3 screws (① : M1.4 × 3.5).

・ Tighten the screw (② : M1.4 × 2).

・ Fit the shutter FPC into the boss of the CCD base and apply the cemedine 575.

・ Solder the shutter FPC.

①

①

Fit the shutter FPC to the boss.

②

Solder it.

Shutter FPC.

CCD base

Adhesive:

Cemedine 575　　

J67017

VAA30001-R.3636.A

- A8･ E4100 -

・ Attach the motor to the cover (① ).

Note : Let the character-stamped surface of the motor face in a correct direction before attaching. (Fig. 1)

・ Tighten the 2 screws (② : M1.4 × 1.8).

・ Insert the shaft ③ and set the gear ④ .

・ Set the gear shaft plate.

・ Tighten the screw (⑤ : M1.4 × 2.5).

・ Insert the shafts (⑥ and ⑦ ) and set the gear ⑧ . Then, set the gear ⑨ .

Assemble Zoom motor unit.

・ Set the cover ⑩ .

・ Tighten the screw (⑪ : M1.4 × 4).

⑨

⑧

⑥

⑦

Gear shaft plate

⑩

⑥ ⑦

Be careful for the length.

Motor

②

④

③

⑤

Gear shaft plate

①

Let the gear face upward and set it.

④

(Fig.1)

※ Character-stamped surface

VAA30001-R.3636.A

- A9･ E4100 -

・ Tighten the screw (⑫ : M1.4 × 2.5).

⑪

⑫

VAA30001-R.3636.A

- A10 ･ E4100 -

・ Attach the zoom motor unit to the CCD base with the lens barrel at the W-end.

・ Tighten the screw (① : M1.4 × 4.2).

・ Tighten the 2 screws (② : M1.4 × 3.5).

・ Set the photo interrupter and tighten the screw (③ : M1.4 × 2.5). (Fig. 1)

Install Zoom motor unit.

・ Solder the FPC.

Photo interrupter

③

①

Zoom motor unit②

VAA30001-R.3636.A

- A11 ･ E4100 -

Finder unit

・ Set the finder unit to W-end manually.

・ Enter the protrusion of the finder unit into the hole of the lens-barrel as shown by ( ), and assemble them by

pushing in the direction of the arrow.

・ Tighten 2 screws (①：M1.4× 3.5).

①

Lens-barrel

Finder unit

VAA30001-R.3636.A

- A12 ･ E4100 -

CCD / TB1-PCB / CP1-PCB

・ Arrange the shield tape (① ), spacer (② ), and lens mount (③ ). Assemble the CCD (④ ) and solder the

CP1-PCB.

・ Solder the lead wires (gray:⑤ and white:⑥ ).

・ Assemble the spacer (⑦ ), LPF(⑧ ), and spacer (⑨ ) into the lens assembly.

・ Attach the CP1-PCB to the lens assembly, and tighten the 2 screws (⑩ : M1.7× 6).

・ Connect the FPC (⑪ ).

・ Tighten the screw (⑫ : M1.7× 3).

・ Place the lead wires in position as shown below, and attach TB1-PCB.

・ Attach the holder AF(⑬ ).

・ Tighten the screw (⑭ : M1.7× 3).

・ Attach the spacer LCD flex (⑮ ).

⑤⑥ ⑨

⑬

④③

②

①

⑮

⑦

⑪

⑫

⑩⑭

⑧

CP1-PCB

TB1-PCB

Lens assembly

Direction for assembling LPF (⑧ )

Lens unit-side

CCD-side

⑤

⑥

TB1-PCB

VAA30001-R.3636.A

- A13 ･ E4100 -

Holder flash

・ Solder the lead wires (red:① , gray:② , and white:③ ). (Fig. 1)

・ Place the lead wires in position as shown below. Attach the holder flash and tighten the screw (④ :M1.7× 4).

(Fig. 2)

Holder microphone

・ Arrange the lead wires (black: ⑤ , red: ⑥ , white: ⑦ and black: ⑧ ) as shown below and solder them.

(Fig. 3・ Fig. 4)

・ Attach the holder microphone.

Spring plate A

・ Attach the spring plate A.

・ Tighten the screw (⑨ : M1.7× 3).

Holder monitor

・ Attach the holder monitor and tighten 2 screws (⑩ : M1.7× 4).

・ Tighten the screw (⑪ : M1.7× 2.5).

LCD

・ Attach the FPC (⑫ ).

・ Attach the LCD.

・ Solder the lead wires (red:⑬ and white:⑭ ). (Fig. 5)

①②③

⑨

⑤⑥⑦⑧

④

⑪

⑩

⑫

⑬⑭

LCD

Spring plate A

Holder microphone

Holder flash

Holder monitor

VAA30001-R.3636.A

- A14 ･ E4100 -

(Fig 3)

(Fig 4)

(Fig 2)

②

①

③

(Fig 1)

②①

③

Arrange wires of Holder microphone

Arrange wires of Holder flash

Holder microphone

For speaker:

Lead wire (red:⑥ )

Lead wire (black:⑤ )

For microphone:

Lead wire (white:⑦ )

Lead wire (black:⑧ )

VAA30001-R.3636.A

- A15 ･ E4100 -

(Fig 5)

⑭ ⑬

Arrange LCD wires

VAA30001-R.3636.A

- A16 ･ E4100 -

Battery cover

Control release / Battery holder

・ Mount the battery cover knob (① ), battery terminal (② ), battery cap (③ ) and battery terminal (④ ) on the

battery cover, and tighten 2 screws (⑤ : M1.7× 2.5).

・ Attach the battery cover and front cover with the battery cover shaft (⑥ ).

・ Attach the control release, and tighten 2 screws (⑦ :M1.7× 3).

・ Attach the terminal (⑧ ) on the battery holder, and tighten the screw (⑨ :M1.7× 2.5).

・ Solder the terminal (⑧ ) and lead wire (red:⑩ ). (Fig. 1・Fig. 2)

・ Attach the terminal (⑪ ) on the battery holder, and tighten the screw (⑨ :M1.7× 2.5).

・ Solder the terminal (⑪ ) and lead wire (black:⑫ ). (Fig. 1・Fig. 2)

・ Attach the battery holder on the front cover, and tighten the screw (⑬ :M1.7× 3).

⑨

⑧

⑩

⑪

⑬

⑫

⑤

④

②

①

③

⑥

⑦

Battery holder

Battery cover

Control release

Front cover

VAA30001-R.3636.A

- A17 ･ E4100 -

(Fig 1)

(Fig 2)

⑩

⑫

⑧

⑪

Arrange lead wires (red:⑩ and black:⑫ )

VAA30001-R.3636.A

- A18 ･ E4100 -

⑥

Front cover

・ Attach the front cover on the body by following the below direction.

・ Attach the stand (tripod:① ).

・ Connect the FPC (② ).

・ Solder the lead wires (black:③ and red:④ ).

・ Tighten 3 screws (⑤ :M1.7× 4).

・ Attach the shaft strap (⑥ ).

③④

①②

⑤

⑤

Front cover

Body

③

④

VAA30001-R.3636.A

- A19 ･ E4100 -

②

rear cover

④

①

③

・ Connect the FPC (① ).

・ Attach the rear cover.

・ Tighten 3 screws (② :M1.7× 4).

・ Tighten 2 screws (③ :M1.7× 4.5).

・ Tighten 2 screws (④ :M1.7× 5).

Rear cover

・ Check if the hole of the rear cover and the USB terminal are aligned.

VAA30001-R.3636.A

- A20 ･ E4100 -

ADJUSTMENT1. Equipment

　　IBM compatible PC/AT • AC adapter EH-62B • USB cable ( UC-E6)

2. Servicing tools

　　• Pattern box • Color meter • Luminance meter • Siemens star chart • Calibration software (J65066)

　　•Adjustment collimator (J63090) or Adjustment firmware

3. Adjustment items and order

1. Lens adjustment

2. AWB adjustment

3. CCD white dot defect compensation

4. CCD black dot defect compensation

5. USB storage information registration

Note) If replacing the lens, CCD, optical filter, CP-1 board, it is necessary to perform the above 1-5

adjustments again. 2-4 adjustments should be made in the above order.

4. Setup

1) System requirements

• Windows® 98 or Me, 2000, XP

• IBM-compatible PC/AT with Pentium or higher processor

• CD-ROM drive

• 3.5-inch 2HD diskette drive

• USB port

• 40 MB or more RAM

• Hard disk drive with 15 MB or more memory space

• VGA or SVGA monitor with 256 or more color display

2) Installing calibration software

• Insert the calibration software installation diskette into the diskette drive.

• Open Explorer.

• Copy "DscCaDI_140" folder of the floppy disk drive in any folder on the hard disk.

VAA30001-R.3636.A

- A21 ･ E4100 -

5. Installing USB driver

If the USB driver is necessary, install Nikon View via CD-ROM packed with the camera.

6. Pattern box

Before using the pattern box, turn its power on to carry out "Aging" approx. 30 minutes: the color temperature

should be 3100 ± 20K by the adjustment with the color meter, and the luminance should be 900 ± 20cd/m2 by the

adjustment with the luminance meter. When using the pattern box and for a while after its power turns off, the

lamp and its surroundings are subject to high temperatures, so care should be taken when handling.

• Procedure for correcting Pattern Box

Note: Be sure to perform the aging correction.

1) Measure the measuring point (center of diffusion plate) with the Color Meter (J63081).

2) Adjust the pattern box so that the color temperature should be 3100±20K by using "VR for adjustment of the

color temperature".

3) Measure the center of the diffusion plate with the Luminance Meter BM-3000 (J63068).

4) Adjust the pattern box so that the luminance should be 900±20cd/m2 by using "Knob for luminance adjustment".

5) Repeat from 1) to 4) So that the color temperature should be 3100±20k and luminance should be 900±20cd/m2.

7. Adjustments required when parts are replaced

Adjustment is necessary. × Adjustment is not necessary.

Lens Adj. AWB CCDDefects

USB Firmwareup

Initial image data

Lens Unit × × ×

Optical filter × × ×

CCD × × ×

CP-1

Power switch

VR for adjustment of the color temperature

Knob for luminanceadjustment

Iris unit

Diffusion plate

Area to be measured

VAA30001-R.3636.A

- A22 ･ E4100 -

8. Connecting the camera to the computer

1) Insert the camera connector of USB cable in the notch of the camera’s USB port.

2) Connect the cable to the USB port on PC.

USBポートへ

USBケーブル

ACアダプター

To USB port

USB Cable

AC Adapter

9. Calibration software

・ Turn on the power switch of the camera.

・When the calibration software starts, the following is displayed on the PC monitor.

VAA30001-R.3636.A

- A23 ･ E4100 -

10. Lens adjustment

※ For the lens adjustment, choose either the infinity adjustment with the collimator or the 1.5-m adjustment with

the adjustment firmware. (However, in case of 1.5-m adjustment, the focus may not be sharp at infinity.)

10-1. Infinity adjustment

[Preparations]

• Turn the power switch of the adjustment collimator (C-DSC) J63090 to on.

• Turn the power switch of the camera to on.

• Siemens star chart

• POWER switch of camera: ON

[Conditions]

• Set the adjustment collimator and the camera (front surface of lens) at the nearest distance between them.

[How to]

• Double-click on "DscCa1Di140".

• Set the siemens star chart so that it comes center of the screen by checking through the viewfinder.

• Click "Focus", then "Yes".

• Lens adjustment value will appear on the screen.

Judgment standard: xd0 = 0±50 , xd7 = 0±50 , xd13 = 0±50, xd19 = 0±50

• Click "OK".

Result of adjustment

カメラ

調整用コリメータ（ジーメンスターチャート内蔵）

Adjustment collimator

(Siemens star chart built-in)

Camera

"Yes"

VAA30001-R.3636.A

- A24 ･ E4100 -

10-2. 1.5-m Adjustment

　※ Before performing the 1.5-m adjustment in this machine, write the adjustment firmware on the camera. After

adjustment, be sure to write the product firmware.

Procedure for setting Adjustment firmware

1) Save the adjustment firmware and the product firmware in any folder.

2) Start up "DscCa1Di140" and click on "Firmware" button on the main menu to write the adjustment firmware.

(If the camera is activated after completing writing the adjustment firmware, "SERVICE" is indicated in red

letters on LCD panel.)

3) Follow the instructions of the below [How-to].

4) Start "DscCaDi140" and click "Firmware" on the main menu to write the product firmware.

[Preparations]

• Set the Siemens star chart.

• Turn the power switch of the camera to on.

[Conditions]

• The siemens star chart should be A3-size or larger (Copy and enlarge A4-size siemens chart included in the

service manual for the usage.)

• Illumination over the object should be 400 lux ± 10%

• Set the siemens star chart and the camera (front surface of lens) at 150 cm ± 3 cm distance between them.

[How-to]

• Double click on "DscCa1Di140".

• Set the siemens star chart so that it comes center of the screen by checking through the viewfinder.

• Click "Focus" then "Yes".

• Lens adjustment values will appear on the screen.

Judgment standard: xd0=0 ± 50, xd7 = 0 ± 50, xd13= 0 ± 50 xd19 = 0 ± 50

• Click "OK".

Result of adjustment

カメラ150cm±3cm

ジーメンススターチャート

Siemens star chart

Camera

"Yes"

VAA30001-R.3636.A

- A25 ･ E4100 -

11. AWB adjustment

[Preparations]

　• Pattern Box(Color temperature: 3100±20K, Luminance: 900±20cd/m2)

[Conditions]

• Set the pattern box and camera (lens front) at "0cm" distance between them.

Note) Do not allow outside light to enter in.

[How to]

• Double-click on "DscCa1Di140".

• Click "AWB", then "Yes".

• AWB adjustment values will appear on the screen.

Judgment standard: CHECK=128±2, 128±2, 130±30

• Click "OK".

カメラ

バターンボックス

Camera

Pattern Box

"Yes"

Result of adjustment

VAA30001-R.3636.A

- A26 ･ E4100 -

12. CCD white dot defect compensation [Conditions]

• With the lens shutter being closed, read the defect of CCD pixels. Then, make the correction data and rewrite the data by the following procedure.

Correct the upper level of defective 1300 pixels from the brightest number of CCD pixels..

[How to]• Double-click on "DscCa1Di140".• Select "CCD Defect" from Test menu of Calibration Software and click the "OK". Refer to FIG-1.• After adjustment, the adjustment value will appear on the screen. Refer to FIG-2.

13. CCD black dot defect compensation [Conditions]

• Fix the camera so that only the white part of the pattern box should be displayed on the screen. (Do not allow outside light to enter in as much as possible.)• With the lens shutter being opend, read the defect (black dots) of CCD pixels. Then, make the correction data and rewrite the data by the following procedure.

Correct the upper level of defective 30 pixels (black dots in bright place) of CCD pixels.

[How to] • Double-click on "DscCa1Di140".

• Select "CCD Black" from Test menu of Calibration Software and click "OK". Refer to FIG-1.• After adjustment, the adjustment value will appear on the screen. Refer to FIG-3.

カメラ

バターンボックスPattern Box

Camera

(FIG-2)

CCD Defect

CCD Black

(FIG-1)

(FIG-3)

VAA30001-R.3636.A

- A27 ･ E4100 -

14. USB storage information registration

USB storage data is important when the camera is connected to a computer via a USB connection.

If there are any errors in the USB storage data, or if it has not been saved, the USB specifications will not be

satisfied, so always check and save the USB storage data.

[How to]

• Connect the camera to a computer.

• Double-click on the "DscCa1Di140".

• Click on the "Get" button in the USB storage window and check the USB storage data.

VID: NIKON

PID: NIKON DSC E4100

Serial:

Rev. : 1.00

• Check the “Serial” in the above USB storage data. If the displayed value is different from the serial number

printed on the base of the camera, enter the number on the base of the camera, and click the "Set" button.

• Check VID and Rev. entries in the USB storage data. If any of them are different from the values in 3. above,

enter the details of 3. and click the "Set" button.

VAA30001-R.3636.A

- E1･ E4100 -

ø

ø

ø

ø

øøøøø

VAA30001-R.3636.A

- E2･ E4100 -

VAA30001-R.3636.A

- E3･ E4100 -

VAA30001-R.3636.A

- E4･ E4100 -

VAA30001-R.3636.A

- E5･ E4100 -

VAA30001-R.3636.A

- E6･ E4100 -

VAA30001-R.3636.A

- E7･ E4100 -

VAA30001-R.3636.A

- E8･ E4100 -

VAA30001-R.3636.A

- E9･ E4100 -

総合結線図

OVERALL WIRING

VSS

NCNC VCOM

GPCK

STBYB

GSRT

STH

RIT

STBYB

VGL

VC1

VC2

GRES

VDD

VGH

NC CP POL

VSH

D00

D03

D04

D01

D02

VRH

VRL

VBC

VDD

VSS

STB

D05

CLK

WHITE

JW505 LED_C

JW504 LED_A

GRAY

JW601 LED_A

JW602 LED_C

CARD/WP

DATA1

DATA0

DATA2

CARD

COMM

AND

DATA3

CLOC

KVSS

VSS

VDD

WP

ZAV_JACK

USB_VDDUSB D(-)

GNDUSB D(+)

AUDIO_OUT

GNDVIDEO_OUT

W1400 XAN (RED)

JW502 BAT-(BLACK)

JW501 BAT+ (RED)

W1600 TRG (GRAY)

FOCUS_ST(B)FOCUS_ST(A)

FOCUS_ST(-A)

Z_PULSE_PI1

SH1

ZOOM_DC1ZOOM_DC2

ZOOM_LEDZ_PULSE_PI2

PIV

FOCUS_LEDFOCUS_PI

PIVZOOM_PI

FOCUS_ST(-B)

Z_PULSE_LED

SP- (RED)

SP+ (BLACK)

W1500 XKT(BLACK)

DP1DP2

SH2

SCAN

IN0E

SCAN

IN1E

SCAN

OUT4

SCAN

IN2E

PW_LED

AL3.2V

NC

MIC (WHITE)

GND (BLACK)

SCAN

OUT2

SCAN

OUT3

SCAN

IN0C

SCAN

OUT0

SCAN

IN3C

SCAN

IN2C

SCAN

OUT1

SCAN

IN1C

SCAN

OUT3

SCAN

IN2D

SCAN

IN3D

SCAN

IN4C

SCAN

IN4D

SCAN

IN1

SCAN

IN3

SCAN

IN3

SCAN

IN4

SCAN

IN2

SCAN

IN2

AF.LE

D(G)

SB.LE

D(R)

AL3.2V

SCAN

IN0D

SCAN

IN1D

SPEAKER

-4

-2

-3

-6

-5

GNDGND

GND

GNDGND

-1 GND

TB1

CP1

LED

USB

LCD PANEL SD

&VIDEO

FLASH

LENS

REFLECTOR

MIC

RELEASEUNIT

BACK SWUNIT

CN110

CN171

CN143

CN951

CN301

CN302

181716151413121110987654321 333231302928272625242322212019 121110987654321

8

7

6

5

4

3

2

1

19

18

17

16

15

14

13

12

11

10

9

8

7

6

5

4

3

2

1

7654321 242322212019181716151413121110987654321

BATTERY

(DMA)(CAA)(SYA)(PWA)

W1-67400/SX795-JNK

MODEL: E4100OVERALL WIRING

VAA30001-R.3636.A

- E10 ･ E4100 -

総合ブロック図

OVERALL BLOCK DIAGRAM

SDRAM

IC103SD(0:31)128Mbit

16MbitFLASH(NOR)

FLASH(NAND)128Mbit

IC121

D(0:15)

FD(0:7)

A(1:20)

CKIN1CKIN2

FSC4

IC111CLOCK GENERATOR

28.63636MHzX1101

CN143SD CARD

IC181AUDIODRIVER

FD(0:4)

IC172AMP

LCD MONITOR

LCDLBRT

LCDVCO

MD

PADYOU

T

LCDPOL

LCDD

(0:5)

LCDCLK

LCDTIM

INGPULSEX8

IC152VIDEO AMP

VOUT

CN110USB/VIDEO

4MHzX3001 X3002

32.768KHz

MRSTZTESTPLLEN

CLKSEL0

SCK

SDISDOSREQ

CN301

IC3018bit Micro Processor

LENS DRIVERIC951

CN951 LENS

3

PICTL

ZMIN1,2

ZPULSE1,2

ZRESET

LENS BLOCK

FIN(1:4)SIN1,2

IIN1,2

Z3001BACKUP

AD(0:9)

ADCK

TGVD,TG

HD

CCDC

K

CCDSD

CCDEN

XV(1:6)

SUBG

T

XSG(1A,2A

,1B,2B

,3)

XSUB

CCD BLOCK

IC101ASIC

4M PixelIC903

V. Driver

IC901IC902

CCDCDS/AGC/AD-C

H. Driver

USBD+

PADAOU

TASICAIN

AUDIO

CONTRO

LSIGN

ALSX5

USBD-

Ni-MH

CP1

LCD BACKLIGHT

DC/DCCONVERTER

ELECTRONICFLASH

VDDREGULATOR

IC302

LENSDC/DC

CONVERTER

IC955

CN302BACK SW UNIT

RELEASE UNIT

MODEL: E4100BLOCK DIAGRAM: OVERALL

BL ON

MIC

SPEAKERAUDIO OUT

IC106D-FF

PWA BLOCK

SYA BLOCK

VAA30001-R.3636.A

- E11 ･ E4100 -

ASIC ブロック図ASIC BLOCK DIAGRAM

DIGITALCLAMP

SIGNALPROCESSOR

AF,AE,AWB

SRAM SRAM

D/ACOMPOSITEVIDEO

NTSC/PAL

ENCODERSRAM

BUS BUS

DIGITALI/F

A/D

D/A

TGCLKGENPLL

SDRAMCONTROLLER

JPEGCONTROLLER

CCD98MHz4fsc

36MHz

72MHz

ARM

UART

USB

SD

PWM

SIOIC301MICROPROCESSOR

EXT PORT(LENS DRIVER)

PIO

BUS I/F

FLASH(NOR)

SDRAM

CCDBLOCK

IC101 ASIC

RGB6bit DATA

CCDDRIVER

AUDIODRIVER

SD CARD

USBCONNECTOR

MODEL: E4100BLOCK DIAGRAM: ASIC

FLASH(NAND)

VAA30001-R.3636.A

- E12 ･ E4100 -

CCDブロック図CCD BLOCK DIAGRAM

LENS

CCD

EF

XV2XV3

XV5

XSG1A

XV6

+12V(A)-8.0V(A)

MN39483PJJ

VDD

VPT

H1

RG

H2

VOUT

O_LPF

IC901

IC903

CH1,C

H2,C

H3,C

H4,C

H5

IV1,IV2,IV3,IV4,IV5,IV6

ISUB

Q9001

XV1

XSG2A

SUB

V.DRIVER

AN20101A

XSG1B

XSG3

SUBGT

IC902

CDS,A/D

C

AD9948KC

PZRL

D2~

D11

31

32

33

AD0

AD9

ADCK

CCDCK

CCDSD

CCDEN

VCC

IC904REG

.TK11130C

S

3.0V+3.45V(A)

VDD3

TOCP1(D

MA)

IC101

ASIC

10

13

17

18

11

1~8

15

19

1,2,21,23,24

20,22,25,26,27,28

3

25

92-4.7-13

27

14,15,21

8

+12V(A)

+3.45V(A)

-8.0V(A)

6,184,5

24, 37, 6

TGVD

TGHD

34, 35

17,22

H.DRIVER

14SUBC

16 HL

XV4

XSUB

XSG2B

V1,V2,V3A,V3B,V4,V5A,V5B,V6

BLOCKDIAG

RAM

:CCD

MODEL:E4100

9-16

VAA30001-R.3636.A

- E13 ･ E4100 -

レンズ駆動ブロック図

LENS DRIVE BLOCK DIAGRAM

IR/SH DRIVER

IN9

IN10

IN11

IN12

OUT9

OUT10

OUT11

OUT12

UNREG

5

6

ZM.MOUT6

OUT5 ZOOM_DC1

ZOOM_DC2IN6

IN5

ZOOM DRIVER

LB8649WIC951

FOCUS DRIVER

IN1

IN2

IN3

IN4 FOCUS_ST(-B)

FOCUS_ST(B)

FOCUS_ST(-A)

FOCUS_ST(A)OUT1

OUT2

OUT3

OUT4

FC.M

17

19

18

16

ZPLUSE1

ZPLUSE2

PICTRL(IC301 23pin)

VDD3

FOCUS_PI

CN951UNIT LENS

SIN1(IC106 12pin)

SIN2(IC106 15pin)

ZPULSE1(IC301 16pin)

ZMIN1(IC301 47pin)

ZMIN2(IC301 46pin)

FIN1(IC106 2pin)

FIN2(IC106 5pin)

FIN3(IC106 6pin)

FIN4(IC106 9pin)

FPIOUT(IC101 231pin)

DP2

DP1

SH2

SH1 4

3

2

1 IR.MIIN1

(IC106 16pin)IIN2

(IC106 19pin)

9

8

14

ZOOM_PI

11

Q9509

IC955L9551D9551C9554

SW REG.BOOST4.35V

ZRESET(IC301 58pin)

Q9501

Q9502ZPULSE2

(IC301 59pin)

PIV12, 15

10

10

7

13

SH.M

5

6

1

2

3

4

9

10

11

12

27

26

37

36

35

34

33

31

30

28

MODEL: E4100BLOCK DIAGRAM: LENS

VAA30001-R.3636.A

- E14 ･ E4100 -

POWER ブロック図POWER BLOCK DIAGRAM

IC501

SWITC

HING

CONTROL

FA7709R

T5001,Q5001

CONVERTO

RTRANS

IC955

STEPUP

CIRCUIT

Q9551,L9551

L5009,Q5003

STEPUP

CIRCUIT

L5004,Q5002

STEPDOWN

CIRCUIT

L5011,Q5009

STEPDOWN

CIRCUIT

+12.0V(A)

-8V(A)

+3.45V(A)

LED_A

VDD3

BOOST4.35V

OUT1

OUT6

OUT2

OUT3

L5007,Q5010

STEPUP

CIRCUIT

OUT4

L5008,Q5013

STEPUP

CIRCUIT

CURRENT

DETEC

TOR

CIRCUIT

IC502REG

.

IC503

REG

ULLATO

R

OUT5

LCDAN

LCDCA

CNT4

9

CNT1

6

CNT2CNT3

CNT6

ON/OFF

78

1131

1617

18

19

CNT5

10

1520

34

MODEL:E4100

BLOCKDIAG

RAM

:POWER

VRVR501

Q5024

PON

AFLEDAN

PAON2

VDD1.7

+15V(L)

+5V(L)

PAON

LCDON3

LCDON

BLON

TODMA(MAIN)

TODMA(MAIN)

TODMA(MAIN)

TOLCD

BACKLIGHT

TOTB1

Q5011

Q5022

Q5014

VAA30001-R.3636.A

- E15 ･ E4100 -

SYSTEM ブロック図SYSTEM BLOCK DIAGRAM

BACKUP CTL

565554

44

3130

43

4647

5916

10

7

8

11

226339

42

511921

35

2 6 32

17

29

37

9

13

56781 2 3 4

38

6257

481

41

334

45

36

50

58

X3001

X300232KHZ

4MHZ

SCAN OUT0

18

SB_LED (R)AF_LED (G)

ZM IN1ZM IN2

ZPULSE2ZPULSE1

XIN

XOUTXCOUT

XCIN

VMONITCHG ON

IC3018bit MICROPROCESSOR

SCAN IN0SCAN IN1SCAN IN2

SCAN OUT1

SCAN OUT2

PLLENBEEP

LCD ON2

PA_ONP ON

LCD ONSELF LED

VMONITCHG

BOOST4.35V

SREQ

P ONPA ON

SPORTSNIGHTVIEW

OK

SCENE LANDSCAPEPORTRAIT

SET UP

PW_ON

LCD ON

PW_LED

1stSI

RESET

BAT OFF

64 BATTERYLI

IC302BATTERYBACKUP

BAT

OFF

AL3.2V

UNREG VDD

RESET

ALWAYS3.2V

IC304RESET IC

4 3

1 2

OUT

VDD

VSS

BACK UP

SO

AUTO

SCAN IN3SCAN IN4

2nd

MOVIE

AV REF ONAVREF

SW3.2V

Q3001

TELE MENUDEL SCAN OUT3

VDDVDD

WIDE

TEST

PW_TEST

PLAY

RIGHTLEFT UP DOWN

CN301CN302

CN301CN302

-

AVJACK SCAN OUT4

SCK

24

34

BLON

MODEL: E4100BLOCK DIAGRAM: SYSTEM CONTROL

BL_ON

ASIC TEST28

60MAIN RESET

CARD

ZRESET

5212

1523

CLKSEL0COMREQ

USB CONNECTPICTL

ZM IN1ZM IN2

ZPULSE2ZPULSE1

TO DMA(MAIN)

TO DMA (MAIN)

PLLENBEEP

LCD ON2

14LCD ON3 LCD ON3SREQSDOSDISCK

ZTESTMRSTZCARD

ZRESET

CLKSEL0COMREQUSB_CNT

PICTL

Z3001

Q3002

Boost4.35V

49SELF LEDPA ON249PA ON2

UNREG

TO DMA (LENS)

VAA30001-R.3636.A

- E16 ･ E4100 -

PWA 回路図 (ストロボ回路図 )PWA CIRCUIT DIAGRAM(STROBE CIRCUIT DIAGRAM)

WT

GR

BAT+JW501

W1400

W1600

W1500

(K)

(K) (400V

)

BAT-JW502

JW504LED_A

IN5+

IN4-

IN5-

IN6-

FB5

FB4

FB6

IN3-

VREGIN2-

IN1-

FB2

FB1

FB3

VCC

CPST

CTST

VBAT

CT

RT

VREF CP

JW505LED_C

PGND

2

CNT4

CNT3

CNT2

PVCC

SEL3

CNT6

CNT5

CNT1

OUT6

OUT2

OUT4

OUT3

OUT0

OUT1

OUT5

CS5

CS6

SEL2

CS1

CS2

ON/OFF

GND

CS4

CS3

PGND

1

2125

1608

2.0A 32V

1608

2.0A 32V

1608

2125

2125

D

2012

POS-CA

P2.0A 32V1608

1608

G

S

1608

H=0.9

5

2016

2016

3216

2125

3216

3216

1608

1608

2.5A 32V1608

D63CB

D52LC

S D

G

D

S

G

1608

1608

D52LC

16081608

3216

3216

1608

32163225

3216

3216

POS-CA

P

3216

CH1 <FOR ANALOG>

<FOR DIGITAL 3.25V>

<FOR DIGITAL POWER SUPPLY>

CH2

CH6

POS-CA

P

<FOR LCD 15.0V>

<FOR DIGITAL 1.7V>

CH4

CH3

CH5 <FOR BACK RIGHT>

RED

2125

XKT

XAN

TRG

RED

H=1.2OM/ORLL57Z

H=1.2OM/ORSO08X1SANZ

OM/ORLIV006HZH=5

H=3

GRAY

BLACK

H=1.7

OM/ORTR01Z

OM/ORD

D58Z

NEW

H=1.9

OM/ORZL17B0120GZH=4.8

OM/ORDD30HVZ

OM/ORTR15Z

OM/ORDD44Z

OM/ORTR02Z

BLACK

FB

H=1.2

H=2

POS-CA

P

OM/ORTR16Z

OM/ORTR25Z

EXT

GND

H=1.3

VDDCE

OM/ORZL51B2350GZH=3.0

H=2

NPVOUT

3.4V

VCONTVIN

REG

IN OFF

GND

H=1.8

H=1.8

(EMD2)

H=2OM/ORLL57Z

OM/ORTR25Z

OM/ORLL47ZH=3 2SA2018

DTC114E

POS-CA

P

H=1.2

H=1

OM/ORIC48FJT1Z

H=2.0OM/ORLL84Z

H=2OM/ORLL57Z

2SA1774VOUT

2SA1774

VIN

GND

DTC144E

POS-CA

P

OM/ORLL84ZH=2.0

DTC144E

DTC144E

2SA1774

LCD_AN

LCD_CA

FLASH REFLECTOR

DS

G

3

290V

BC

E

BCE

DB320C

EDK3

16BJ475K

D-T

DB320C

EDK3

16BJ225K

D-T

L5015 F5003

F5004

D9551L9551

T5402

D5404

D5408

R5426

R5418

D5405

C5410

Q5409

R5425

R5423

R5424

C5409

R5422

C5411

R5408

R5406C5403

R5432

D5402D5403

R5419

R5409

C5420

C5404

C5401

T5401

C5406

Q5407

R5414

Q5410 Q5411

R5429

R5433

R5430R5431R5413

R5420

R5417

Q5401

Q5405

R5401

Q5402

D5407

C5407

C5413

RB504

L5014

C9551

R9554

R9553

R9552

C9554

R9551

Q9552

R5117

C9553C9

552

Q9551

IC955

L5016

T5001

D5010

C5023

F5001

C5064

Q5001

L5002

L5001

RB502

R5022

R5025

C5035

IC503

C5037

R5024

C5033

R5112

Q5018

R5113

C5031

C5032

C5034

C5036

R5023

D5001

RB505

R5097

C5079

C5001

C5002

C5020

IC501

C5019

C5018

C5021

C5013

C5016

R5011

C5017

VR501

D5013

F5002 L5009

L5004

RB506

RB501

R5099

C5043

D5005

D5004

D5008

RB503

R5026

Q5023Q5020

R5074

C5038

C5075

Q5024

R5072

R5071

C5078

R5084

Q5002

R5035

R5034R5

033

Q5003

C5014

C5008

C5009

C5010

C5011

C5006

C5012

C5022

L5007

C5080

L5011

C5048

R5114

D5006

R5042

C5053

C5047

C5052

Q5010

Q5009

C5068

R5054

Q5011

R5053

C5069

C5070

Q5014IC502

R5052

R5051

R5044

R5045

R5043

L5008

R5055

R5063

R5068

R5062

C5061

Q5022

R5091

R5090

R5067

D5007

C5062

R5061

Q5013

F47K2R0D3LTND

F47K2R0D3LTND

SD833-04SC10;M

CMC0

1MA

2SD1

9

470K

;1/16J

56;1/16J

S6A37

0.047;350H

CY25BAJ-8F

100K

;1/8J-X

33;1/16J

220;1

/16J

0.033;F

220K

;1/8J-X

0.01;630H

120;1/16J

100;1/16J0.068;B

3.9K;1/1

6D

F1P8RR264M-400

82K;1/1

6D

1.2K;1/1

6J

4700P;B

1000P;B

47;6.3-V

0.01;B

3LN01S

1K;1/16J

2SA1745 DTC144EM

6.2K;1/1

6D

100K

;1/16J

4.7K;1/16J100K

;1/16J

10K;1/1

6J

10K;1/1

6D

10M;1/8

F-X

DTC123JE

CPH5504

1K;1/16J

DTC114EM

DAN2

22

6800P;B

6800P;B

1M

10;6.3B

560K

;1/16D

130K

;1/16D

15K;1/1

6D33;8-V

390K

;1/16D

DTC144EM

0;1/16Z

330P

;B10;6.3B

FDC633N

XC9104D095MP

10;M

MA2S

D19

33;10

-V

F47K2R0D3LTND

1;B

CPH3413

47;K

100;K

18

2.2K;1/1

6J

13K;1/1

6D

0.1;B

TK11134CS

1;B

150K

;1/16D

1;B

100K

;1/16J

2SA1774(R)

82K;1/16J

2.2;16

B

10;B

10;10

B

2200P;B 0;1

/16Z

HN2D01JE

1M

910;1/16J

0.01;B

0.01;B

1000P;B

0.1;B

2200P;B

6800P;B

4700P;B

150P;CH

1;B

9.1K;1/16D

0.47;B

3.3K

MA2SD19

F47K2R5D3LTND

4.7;M

10;M

47K

750

11;1/16D

33;8-V

MA2Z720

MA22D1

5

SD833-04SC

75

470;1

/16D

EMH10EMD2

56K;1/1

6J

2200P;B

47;6.3-V

EMF21

2.2K;1/1

6J100K

;1/16J

2200P;B

0;1/16

Z

CPH3313

5.36K

;1/16D

12K;1/1

6D

0;1/16

Z

CPH3409

FA7709R-H1

6800P;B

0.033;B

0.1;B

0.1;B

0.022;B

0.033;B0.1;B

6.8;M

1;B

1;B

10;M

33;8-V

47K;1/16J

MA22D1

5

56K;1/1

6J

4700P;B

2200P;B

4.7;B

MCH5809

MCH3319

1;B

150K

;1/16D

EMF18

1K;1/16J

1;16B

1;B

EMF18XC6202P502MR

22K;1/1

6J100K

;1/16J

11.8K

;1/16D

16.9K

;1/16D

0;1/16

Z

6.8;M

10.7K

;1/16D

45.3;1/1

6D

33K;1/1

6J

10K;1/16D

2.2;B

EMF18

22K;1/1

6J

100K

;1/16J

100K

;1/16J

MAZS

1600ML

4700P;B

1K;1/16J

MCH5809

16V

6.3V

16V

16V

6.3V

6.3V

6.3V

6.3V16

V

6.3V

1AV4L26B3450G

1AV4L17B0160N

1AV4L17B0200G

1AV4L26B3450G

TFDC633N----K

QXC9104D095MP

1AV4L2FM100MG

1AV4L51B6070G 1AV4L2FB470KG

1AV4L2FB101KG

QTK11134CS--J

CK1C

105K

GWBN

G

1AV4L2JQ6R8MG

CK1C

475K

SVBN

G

TMCH3319----P

1AV4L2JQ6R8MG

CK1C

225K

SVBN

G

BOOST4.35V

UNREG

VMONIT

TRIG

STOP

RDY

CHG

PAON

+3.45V(A)

-8.0V(A)

+12V(A)

AFLED_AN

AFLED_CA

SELFLED

VDD3

PAON2

+5V(L)

LCDON

+15V(L)

PON

VDD1.7

LCDON3

BLON

1

2

1

8765

4 3 2 1

3

2

13

254

2 1

543

6 5 4

321

54

3 2 1

1

5

4 3

2

13

2

6

5

7

8

4

5

43

2

1

1

2

3

4

5

404142434445464748

32

33

34

35

36

373839654

3 2 16 5 4

321

3

2

1 6

5

4

6

7

8

9

10

11

12

13 14 15 16 17 18 19 20 21 22 23 24

25

26

27

28

29

30

31

5 4

321

3

2

1 6

5

4 2

3

2

1 6

5

4

1

3

2

1 6

5

4

3

5 4

321

SW REG.

SWITCHING CONTROL

REG.

TO TB1

TO DMA(MAIN)

TO DMA(LENS)

TO DMA(MAIN)

TO LCD BACK LIGHT

TO DMA(MAIN)

!

P1-67400/SX795-JNK

PWA

!

!

!

CIRCUIT DIAGRAM: CP1(PWA)

MODEL: E4100

WHITE

RED

VAA30001-R.3636.A

- E17 ･ E4100 -

FUSE ARRANGEMENT (CP1 PCB)

F5001F5004F5002

F5003

Fuse Function Phenomenon when it has blown out singly

Rating

　F5001 Used to protect the unit when the DC/DC converter circuit malfunctions.

The power of the camera is not turned on.

２．０A　３２V

　F5002 Used to protect the unit when the DC/DC converter circuit malfunctions.

The power of the camera is not turned on.

２．５A　３２V

　F5003 Used to protect the unit when the lens system DC/DC converter circuit malfunctions.

The power of the camera is not turned on.

２．０A　３２V

　F5004 Used to protect the unit when the speed light charging circuit malfunctions.

The condenser is not charged.

２．０A　３２V

VAA30001-R.3636.A

- E4100 -

The contents of inspection standards and tools for E4100

[1] Inspection standards ................................................................................................................................. R1 to R7

[2] Tools ......................................................................................................................................................... T1 to T3

VAA30001-R.3636.A

- T1･ E4100 -

［２］ 工具一覧表　　Tool List

※：新規工具

※：New tool

工具番号

Tool No.

J63080

J63080A

J63081

J63068

名　　称

Name

パターンボックス　LV-1450DC

Pattern Box LV-1450DC

交換用ハロゲンランプ (LV-1450DC用 )

Spare Harogen Lamp (For LV-1450DC)

カラーメータ (ミノルタカラーメータⅢ F)

Color Meter(Minolta Color meterⅢ F)

輝度計 BM-3000

Luminance Meter BM-3000

備　考

Remarks

共通 (E4300, E3500,

E3100, E2100, E5400,

E3700, E3200, E2200,

E8700, E4100)

Common(E4300, E3500,

E3100, E2100, E5400,

E3700, E3200, E2200,

E8700, E4100)

LV-1450DC

Exclusive

共通

Common

共通

Common

POWER

BM-3000

VAA30001-R.3636.A

- T2･ E4100 -

※：新規工具

※：New tool

工具番号

Tool No.

J65066

J63090

サービスマニュアル添付

Attached in

Service Manual

名　　称

Name

キャリブレーションソフト

Calibration Software

コリメータ (C-DSC)

Collimator (C-DSC)

ジーメンスチャート

Siemens chart

備　考

Remarks

共通 (E995,E775,E885

E5000, E2500, E4500

E5700, E4300, E3500

E3100, E2100, E5400

E3700, E3200, E2200

E8700, E4100)

Common(E995,E775,E885

E5000, E2500, E4500

E5700, E4300, E3500

E3100, E2100, E5400

E3700, E3200, E2200

E8700, E4100)

共通

Common

共通

Common

※

VAA30001-R.3636.A

- T3･ E4100 -

ジーメンススターチャート