作成承認印 配布許可印
Copyright c 2004 by Nikon Corporation.
All Rights Reserved.
無断転載を禁ず!!
Printed in Japan May 2004
VAA30001-R.3636.A
REPAIR MANUAL
VAA30001
VAA30001-R.3636.A
- E4100 -
SPECIFICATIONS ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・M1-M2
DISASSEMBLING
WARNING ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・D1
Rear cover ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・D2-D3
Discharge Main condenser・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・D4
Front cover ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・D5
Battery cover / Battery terminal・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・D6
Battery holder / Battery terminal / Control release ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・D6
LCD ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・D7
Holder monitor・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・D7
Spring plate A ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・D7
Holder microphone ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・D7
Holder flash ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・D7
CP1-PCB / TB1-PCB / CCD ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・D8
Finder unit ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・D9
Separate Zoom motor unit ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・D10
Disassemble Zoom motor unit・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・D11
Separate Lens-barrel ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・D12
Shutter ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・D13-D14
Straight tube (1st lens frame) / key tube ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・D15
3rd lens unit / Zoom motor unit ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・D16
ASSEMBLY
Barrier unit・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・A1
Straight tube (1st lens frame) / key tube ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・A2
Shutter ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・A3-A4
3rd lens unit ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・A5
Assemble Lens-barrel / CCD base ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・A6-A7
Assemble Zoom motor unit ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・A8-A9
Install Zoom motor unit ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・A10
Finder unit ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・A11
CCD / TB1-PCB / CP1 -PCB ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・A12
Holder flash ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・A13
Holder microphone ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・A13
Spring plate A ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・A13
Holder monitor・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・A13
LCD ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・A13
Arrange wires of Holder flash ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・A14
Arrange wires of Holder microphone ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・A14
Arrange LCD wires ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・A15
CONTENTS
VAA30001-R.3636.A
- E4100 -
Battery cover ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・A16
Control release / Battery holder ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・A16-A17
Front cover ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・A18
Rear cover ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・A19
ADJUSTMENT ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・A20-A27
DISCRIPTION OF CIRCUIT・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・E1-E8
ELECTRICITY
OVERALL WIRING ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・E9
OVERALL BLOCK DIAGRAM ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・E10
ASIC BLOCK DIAGRAM ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・E11
CCD BLOCK DIAGRAM ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・E12
LENS DRIVE BLOCK DIAGRAM ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・E13
POWER BLOCK DIAGRAM・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・E14
SYSTEM BLOCK DIAGRAM・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・E15
PWA CIRCUIT DIAGRAM (STROBE CIRCUIT DIAGRAM) ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・E16
FUSE ARRANGEMENT (CP1 PCB) ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・E17
INSPECTION STANDARD・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・R1-R7
TOOL LIST ・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・・T1-T3
VAA30001-R.3636.A
- M1・ E4100 -
Type E4100 digital camera
Effective pixels 4.0 mega-pixels
CCD 1/2.5-inch high-density CCD; total pixels: 4.23 mega-pixels
Image size (pixels) 2288×1712, 2048×1536, 1600×1200, 1024×768 and 640×480
Lens 3×Zoom Nikkorf = 5.8 to 17.4mm (38 ~ 105mm by conversion with 35mm-format) F2.8 ~ F4.9
Digital zoom Max. 4.0× (35-mm [135] camera-format equivalent: 460 mm)
Auto focus (AF) Contrast AF
Focus range measured from lens
30 cm (1’~∞ ) - ∞ ; macro mode 4 cm/1.6”(W) - ∞
AF area Automatically selected from 5 places when the scene mode with the center/assist function is selected.
Finder Real image type zoom finder, field of viewfinder: Approx. 80%
Monitor 1.6”, 80,000-dot, amorphous silicon TFT LCD monitor
StorageMediaFile system
File format
Internal memory (14.5 MB)/SD memory cardsCompliant with Design rule for Camera File systems (DCF), Exif 2.21, Digital Print-Order Format (DPOF)Compressed: Compliant with JPEGMovies: QuickTime Motion JPEG
Metering 256-segment matrix metering linked to AF area(when frame is displayed in frame-assisted scene mode)
Exposure control Programmed auto, exposure compensation (–2.0 ~ +2.0 EV in steps of 1/3 EV)
Range(ISO equivalent)
W: EV 1 to 17.8T: EV 2.6 to 16.2
Shutter Mechanical and charge-coupled electronic shutter
Shutter Speed 4-1/3000 sec.
ApertureRange
Electronically controlled open-selectable aperture, control steps: 2 (f/2.8 and f/5.6 [W])
Sensitivity Approximately equivalent to ISO 50 (auto gain of two to four times) (up to equivalent of ISO200)
Self-timer Ten-second duration
SPECIFICATIONS
VAA30001-R.3636.A
- M2・ E4100 -
Built-in SpeedlightRange
Sync method
Equipped with automatic pop-upW: 0.4 to 3.4 m (1.3 to 11.2 ft.)T: 0.4 to 2.0 m (1.3 to 6.6 ft.)Automatic sync control
Interface USB
Video output User can choose from NTSC and PAL
I/O terminals DC input terminal, AV output terminal which is also used as USB terminal
Power sources Two rechargeable Nikon EN-MH1 NiMH batteries, One CR-V3 lithium battery,
Two LR6 (AA) alkaline batteries, . Two ZR6 (AA) nickel manganese batteries,
Two FR6/L91 (AA) lithium batteries, EH-62B AC adapter
Number of frames taken in succession
110 frames (alkaline batteries)/260 frames (EN-MH1)/530 frames (CR-V3)
Dimensions(W×H×D)
88×65×38 mm (3.5” × 2.6” × 1.5”)
Weight Approximately 140 g without battery and memory card
Operating environmentTemperatureHumidity
0 - 40°C (32 – 104°F)Under 85% (no dew condensation)
VAA30001-R.3636.A
- D1・ E4100 -
Disassembly
Note : ① Be sure to remove the SD memory card and batteries before disassembly. ② When disassembling, make sure to memorize the processing state of wires,
screws to be fixed and their types, etc. ③ Because electrical parts are easily damaged by static electricity, make sure
that you are well earthed/grounded.
・Lead-free solder is used for this product.・For soldering work, the special solder and soldering iron are required.・Do NOT mix up lead-free solder with traditional solder.・Use the special soldering iron respectively for lead-free solder and lead solder.
They cannot be used in common.
VAA30001-R.3636.A
- D2・ E4100 -
Rear cover
・ Open the cover (① ).
・ Take out 2 screws (② : M1.7× 5).
・ Take out 2 screws (③ : M1.7× 4.5).
・ Take out 2 screws (④ : M1.7× 4).・ Open the SD card cover side of the rear cover and unhook it as pushing its top by your finger. (Fig. 1)
・ Uncover the rear cover by pulling it slowly backwards, and detach the FPC (⑤ ) from the connector. (Fig. 2)
・ The shaft strap (⑥ ) comes off.
①
②
③
④
⑤
⑥
Rear cover
VAA30001-R.3636.A
- D3・ E4100 -
FPC⑤
(Fig 2)
(Fig 1)
Rear cover
SD card cover
Push.
Push.Push.
VAA30001-R.3636.A
- D4・ E4100 -
Discharge Main condenser
2KΩ/5W
VAA30001-R.3636.A
- D5・ E4100 -
Front cover
・ Remove the lead wire (black:① ) and lead wire (red:② ).・ Remove the FPC (③ ).・ Take out 3 screws (④ : M1.7× 4).・ Remove the front cover by pulling it forwards.・ The stand (tripod:⑤ ) comes off.
Front cover
③
①②
⑤
④
⑤
①
②
VAA30001-R.3636.A
- D6・ E4100 -
・ Take out 2 screws (① : M1.7× 2.5), and remove the battery terminal (② ).
・ The battery cap (③ ), battery terminal (④ ) and battery knob (⑤ ) come off.
・ Remove the battery cover shaft (⑥ ) and uncover the battery cover.
Battery cover / Battery terminal
・ Take out 2 screws (⑦ : M1.7× 3), and remove the battery holder.
・ Take out 2 screws (⑧ : M1.7× 2.5).
・ Remove the lead wire (black: ⑨ ) and detach the terminal (⑩ ).
・ Remove the lead wire (red: ⑪ ) and detach the terminal (⑫ ).
・ Take out 2 screws (⑬ : M1.7× 3) and remove the control release.
Battery holder / Battery terminal / Control release
②
④⑤
Front cover
Battery holder
Battery cover
③
①
⑩
⑦
⑧
⑨
Control release
⑪
⑫
⑥
⑬
VAA30001-R.3636.A
- D7・ E4100 -
LCD
・ Remove the FPC (① ).
・ Remove the lead wires (white:② and red:③ ). (Fig. 1)
・ Remove the LCD.
Holder monitor
・ Take out 2 screws (④ : M1.7× 4).
・ Take out the screw (⑤ : M1.7× 2.5).
・ The holder monitor comes off.
Spring plate A
・ Take out the screw (⑥ : M1.7× 3).
・ The spring plate A comes off.
Holder microphone
・ Remove the lead wires (red: ⑦ and black: ⑧ ).
・ Remove the lead wires (white: ⑨ and black ⑩ ).
・ The holder microphone comes off.
Holder flash
・ Take out the screw (⑪ : M1.7× 4).
・ Remove the lead wires (black:⑫ , gray:⑬ and red:⑭ ).
・ The holder flash comes off.
(Fig.1)② ③
⑫⑬⑭
⑦⑧⑨⑩
Spring plate A
⑤
⑥
LCDHolder microphone
Holder flash
④
①
Holder monitor
⑪
②③
VAA30001-R.3636.A
- D8・ E4100 -
CP1-PCB / TB1-PCB / CCD
・ Take out the screw (① : M1.7× 3).・ Remove the FPC (② ).・ Take out 2 screws (③ : M1.7× 6).・ The lens assembly comes off.・ The spacer (④ ), LPF (⑤ ) and spacer (⑥ ) come off.・ Remove the lead wires (gray:⑦ and white:⑧ ).・ Remove the spacer LCD flex (⑨ ).・ Take out the screw (⑩ : M1.7× 3).・ Remove the holder AF (⑪ ).・ TB1-PCB comes off.・ Unsolder the CCD (⑫ ) and disassemble the CCD and CP1-PCB.
⑫⑥
③
①
⑤
④
⑨
⑦⑧
⑪
⑩
②
CP1-PCB
Lens assembly
TB1-PCB
VAA30001-R.3636.A
- D9・ E4100 -
Finder unit
・ Take out 2 screws (① ).
・ Remove the finder unit by lifting it in the direction indicated by the arrow.
①
Lens-barrel
Finder unit
Note : All of the FFD adjustment tools are not prepared yet. The lens-barrel can be
disassembled and assembled. However, each of the 1st, 2nd and 3rd lens group units
(lens) cannot be replaced with a new one.
VAA30001-R.3636.A
- D10 ・ E4100 -
Separate Zoom motor unit.
・ Unsolder the FPC unit.
・ Take out the screw (① : M1.4 × 2.5).
・ Remove the photo interrupter FPC.
・ Take out the screw (② : M1.4 × 4.2).
・ Take out the 2 screws (③ : M1.4 × 3.5).
・ The zoom motor unit comes off.
③
Photo interrupter
Zoom motor unit ①
②
VAA30001-R.3636.A
- D11 ・ E4100 -
① ②③
Hook
④
⑤
⑥
⑦⑧
Gear shaft plate
Motor
⑪
⑨
⑩
⑧
Gear shaft plate
Disassemble Zoom motor unit.
・ Take out the screw (① : M1.4 × 2.5). ・ Take out the screw (② : M1.4 × 4).
・ Unhook and remove the cover ③ .
・ Remove the gears ( ④ and ⑤ ) and remove the
shafts (⑥ and ⑦ ).
・ Take out the screw (⑧ : M1.4 × 2.5).
・ Remove the gear shaft plate.
・ Remove the gear (⑨ ) and remove the shaft (⑩ ).
・ Take out the 2 screws (⑪ : M1.4 × 1.8).
・ The motor comes off.
VAA30001-R.3636.A
- D12 ・ E4100 -
・ Detach the lens barrel by moving it slowly in the direction indicated by the arrow.
The finder gear A and B come off at the same time.
・ Remove the gear shaft.
Separate Lens-barrel
・ Remove the solder of the shutter FPC and take out the screw (①:M1.4× 2).
・ Take out 3 screws (②:M1.4× 3.5).
・ Remove the shutter FPC from the CCD base.
②
②
①
Remove it from the boss. (It is adhered.)
CCD base
Shutter FPC
Gear shaftShutter FPC
Lens-barrel
Finder gear B
Finder gear A
VAA30001-R.3636.A
- D13 ・ E4100 -
・ Remove the barrier joint plate by pulling it in the direction of A.
Shutter
・ Rotate the turning tube in the direction indicated by the arrow, to extend the lens-barrel to the maximum.
Turning tube
A①
②
Barrier joint plate
【Side view】
AA
Barrier joint plate
VAA30001-R.3636.A
- D14 ・ E4100 -
・ Take out 2 screws (①:M1.4× 3.5) to separate the 2nd lens frame from the shutter.
・ Rotate the turning tube to the full up position, to reduce the lens-barrel size.
・ Remove the shutter unit by lifting it in the direction of the arrow.
①
Shutter
2nd lens frame
Turning tube
Shutter unit
Note : The 2nd lens group unit (frame) cannot be replaced with a new one.
VAA30001-R.3636.A
- D15 ・ E4100 -
Note : The 1st lens group unit (frame) cannot be replaced with a new one.
・ Remove the turning tube unit from the lens-barrel cover.
・ Remove the straight tube (1st lens frame) by pulling it backwards.
・ Remove the key tube backwards. (It is a little difficult to remove the key tube because it is fixed with hooks.)
Note : The key tube can be easily damaged. Perform its removal carefully.
Straight tube (1st lens frame) / key tube
Barrier unit
・ Remove the name plate.
・ Remove the barrier by turning it slightly in the direction indicated by the arrow.
・ Detach the spring to remove the barrier ring.
Turning tube unit
Lens-barrel cover
Barrier ring
Name plate
Barrier
Spring
Hook
Hook
Straight tube (1st lens frame)
Key tube
Turning tube
VAA30001-R.3636.A
- D16 ・ E4100 -
Note : The 3rd lens group unit (frame) cannot be replaced with a new one.
・ Remove the 3rd lens spring.
・ Turn the focus motor shaft counterclockwise with a flathead screw driver, and remove the 3rd lens unit and
turning stopper.
3rd lens unit / Zoom motor unit
Focus motor3rd lens unit
Turning stopper
3rd lens spring
VAA30001-R.3636.A
- A1・ E4100 -
AssemblyBarrier unit
・ Attach the barrier ring to the straight tube (1st lens frame), and hook the spring.
・ Attach the barrier by turning it slightly in the direction indicated by the arrow.
・ Attach the name plate.
Barrier ring
Name plate
Barrier
Spring
Straight tube (1st lens frame)
VAA30001-R.3636.A
- A2・ E4100 -
Finished unit
・ Align Section A with Section B and push in the key tube by turning counterclockwise.
・ Turn the key tube clockwise until it contacts with the stopper.
・ Align Section D of the 1st lens frame with Section C of the turning tube and assemble them.
Straight tube (1st lens frame) / key tube
Section A
Section B
Turning tube
Light-shielding ring
Key tube
Section A
Section D
Section C
Straight tube (1st lens frame)
Key tube
Lens-barrel cover
Turning tube unit
・ Assemble the turning tube unit into the lens-barrel cover.
VAA30001-R.3636.A
- A3・ E4100 -
Shutter
・ Assemble the shutter unit into the turning tube by following the above direction of the arrow.
・ Assemble the shutter and 2nd lens frame with 2 screws (①:M1.4× 3.5).
①
Shutter
2nd lens frame
Lens-barrel cover
Shutter unit
VAA30001-R.3636.A
- A4・ E4100 -
・ Attach the barrier joint plate by pressing slightly in the direction of A arrow.
【Side view】
・ Rotate the turning tube in the direction indicated by the arrow, to extend the lens-barrel to the maximum.
Barrier joint plate
Turning tube
・ Rotate the turning tube in the direction indicted by the arrow, to reduce the lens-barrel size.
A①
②
Barrier joint plate
AA
Barrier joint plate
VAA30001-R.3636.A
- A5・ E4100 -
3rd lens unit
・ Hook the 3rd lens spring.
・ Apply the Screw lock (colorless) on both hooking ends of the 3rd lens spring.
・ While turning the focus motor shaft clockwise with a flathead screwdriver, assemble the 3rd lens unit and the
turning stopper into the CCD base.
・ Turn the focus motor shaft further until the 3rd lens unit slightly touches the bottom, then give it about one turn
counterclockwise.
Adhesive: Screw lock
(Colorless)
HH201002
Focus motor3rd lens unit
Turning stopper
3rd lens spring
VAA30001-R.3636.A
- A6・ E4100 -
・ Attach the gear A to the CCD base.
・ Attach the finder gear B to the CCD base.
・ Pass the shutter FPC through the hole of the CCD base, and assemble the lens-barrel.
・ Set the finder gear C and insert the gear shaft.
・ Apply the cemedine 575 on the tip of the gear shaft from the rear surface of the CCD base.
・ Apply the cemedine 575 on the tip of the gear shaft.
Assemble Lens-barrel / CCD base
Finder gear CAdhesive:
Cemedine 575
J67017
Tip of gear shaft
CCD base
Adhesive:
Cemedine 575
J67017
Gear A(This surface must be at the lens-barrel side.)
Shutter FPC
Lens-barrel
CCD base
Finder gear C
Finder gear B(This surface must be at the lens-barrel side.)
VAA30001-R.3636.A
- A7・ E4100 -
・ Tighten the 3 screws (① : M1.4 × 3.5).
・ Tighten the screw (② : M1.4 × 2).
・ Fit the shutter FPC into the boss of the CCD base and apply the cemedine 575.
・ Solder the shutter FPC.
①
①
Fit the shutter FPC to the boss.
②
Solder it.
Shutter FPC.
CCD base
Adhesive:
Cemedine 575
J67017
VAA30001-R.3636.A
- A8・ E4100 -
・ Attach the motor to the cover (① ).
Note : Let the character-stamped surface of the motor face in a correct direction before attaching. (Fig. 1)
・ Tighten the 2 screws (② : M1.4 × 1.8).
・ Insert the shaft ③ and set the gear ④ .
・ Set the gear shaft plate.
・ Tighten the screw (⑤ : M1.4 × 2.5).
・ Insert the shafts (⑥ and ⑦ ) and set the gear ⑧ . Then, set the gear ⑨ .
Assemble Zoom motor unit.
・ Set the cover ⑩ .
・ Tighten the screw (⑪ : M1.4 × 4).
⑨
⑧
⑥
⑦
Gear shaft plate
⑩
⑥ ⑦
Be careful for the length.
Motor
②
④
③
⑤
Gear shaft plate
①
Let the gear face upward and set it.
④
(Fig.1)
※ Character-stamped surface
VAA30001-R.3636.A
- A9・ E4100 -
・ Tighten the screw (⑫ : M1.4 × 2.5).
⑪
⑫
VAA30001-R.3636.A
- A10 ・ E4100 -
・ Attach the zoom motor unit to the CCD base with the lens barrel at the W-end.
・ Tighten the screw (① : M1.4 × 4.2).
・ Tighten the 2 screws (② : M1.4 × 3.5).
・ Set the photo interrupter and tighten the screw (③ : M1.4 × 2.5). (Fig. 1)
Install Zoom motor unit.
・ Solder the FPC.
Photo interrupter
③
①
Zoom motor unit②
VAA30001-R.3636.A
- A11 ・ E4100 -
Finder unit
・ Set the finder unit to W-end manually.
・ Enter the protrusion of the finder unit into the hole of the lens-barrel as shown by ( ), and assemble them by
pushing in the direction of the arrow.
・ Tighten 2 screws (①:M1.4× 3.5).
①
Lens-barrel
Finder unit
VAA30001-R.3636.A
- A12 ・ E4100 -
CCD / TB1-PCB / CP1-PCB
・ Arrange the shield tape (① ), spacer (② ), and lens mount (③ ). Assemble the CCD (④ ) and solder the
CP1-PCB.
・ Solder the lead wires (gray:⑤ and white:⑥ ).
・ Assemble the spacer (⑦ ), LPF(⑧ ), and spacer (⑨ ) into the lens assembly.
・ Attach the CP1-PCB to the lens assembly, and tighten the 2 screws (⑩ : M1.7× 6).
・ Connect the FPC (⑪ ).
・ Tighten the screw (⑫ : M1.7× 3).
・ Place the lead wires in position as shown below, and attach TB1-PCB.
・ Attach the holder AF(⑬ ).
・ Tighten the screw (⑭ : M1.7× 3).
・ Attach the spacer LCD flex (⑮ ).
⑤⑥ ⑨
⑬
④③
②
①
⑮
⑦
⑪
⑫
⑩⑭
⑧
CP1-PCB
TB1-PCB
Lens assembly
Direction for assembling LPF (⑧ )
Lens unit-side
CCD-side
⑤
⑥
TB1-PCB
VAA30001-R.3636.A
- A13 ・ E4100 -
Holder flash
・ Solder the lead wires (red:① , gray:② , and white:③ ). (Fig. 1)
・ Place the lead wires in position as shown below. Attach the holder flash and tighten the screw (④ :M1.7× 4).
(Fig. 2)
Holder microphone
・ Arrange the lead wires (black: ⑤ , red: ⑥ , white: ⑦ and black: ⑧ ) as shown below and solder them.
(Fig. 3・ Fig. 4)
・ Attach the holder microphone.
Spring plate A
・ Attach the spring plate A.
・ Tighten the screw (⑨ : M1.7× 3).
Holder monitor
・ Attach the holder monitor and tighten 2 screws (⑩ : M1.7× 4).
・ Tighten the screw (⑪ : M1.7× 2.5).
LCD
・ Attach the FPC (⑫ ).
・ Attach the LCD.
・ Solder the lead wires (red:⑬ and white:⑭ ). (Fig. 5)
①②③
⑨
⑤⑥⑦⑧
④
⑪
⑩
⑫
⑬⑭
LCD
Spring plate A
Holder microphone
Holder flash
Holder monitor
VAA30001-R.3636.A
- A14 ・ E4100 -
(Fig 3)
(Fig 4)
(Fig 2)
②
①
③
(Fig 1)
②①
③
Arrange wires of Holder microphone
Arrange wires of Holder flash
Holder microphone
For speaker:
Lead wire (red:⑥ )
Lead wire (black:⑤ )
For microphone:
Lead wire (white:⑦ )
Lead wire (black:⑧ )
VAA30001-R.3636.A
- A15 ・ E4100 -
(Fig 5)
⑭ ⑬
Arrange LCD wires
VAA30001-R.3636.A
- A16 ・ E4100 -
Battery cover
Control release / Battery holder
・ Mount the battery cover knob (① ), battery terminal (② ), battery cap (③ ) and battery terminal (④ ) on the
battery cover, and tighten 2 screws (⑤ : M1.7× 2.5).
・ Attach the battery cover and front cover with the battery cover shaft (⑥ ).
・ Attach the control release, and tighten 2 screws (⑦ :M1.7× 3).
・ Attach the terminal (⑧ ) on the battery holder, and tighten the screw (⑨ :M1.7× 2.5).
・ Solder the terminal (⑧ ) and lead wire (red:⑩ ). (Fig. 1・Fig. 2)
・ Attach the terminal (⑪ ) on the battery holder, and tighten the screw (⑨ :M1.7× 2.5).
・ Solder the terminal (⑪ ) and lead wire (black:⑫ ). (Fig. 1・Fig. 2)
・ Attach the battery holder on the front cover, and tighten the screw (⑬ :M1.7× 3).
⑨
⑧
⑩
⑪
⑬
⑫
⑤
④
②
①
③
⑥
⑦
Battery holder
Battery cover
Control release
Front cover
VAA30001-R.3636.A
- A17 ・ E4100 -
(Fig 1)
(Fig 2)
⑩
⑫
⑧
⑪
Arrange lead wires (red:⑩ and black:⑫ )
VAA30001-R.3636.A
- A18 ・ E4100 -
⑥
Front cover
・ Attach the front cover on the body by following the below direction.
・ Attach the stand (tripod:① ).
・ Connect the FPC (② ).
・ Solder the lead wires (black:③ and red:④ ).
・ Tighten 3 screws (⑤ :M1.7× 4).
・ Attach the shaft strap (⑥ ).
③④
①②
⑤
⑤
Front cover
Body
③
④
VAA30001-R.3636.A
- A19 ・ E4100 -
②
rear cover
④
①
③
・ Connect the FPC (① ).
・ Attach the rear cover.
・ Tighten 3 screws (② :M1.7× 4).
・ Tighten 2 screws (③ :M1.7× 4.5).
・ Tighten 2 screws (④ :M1.7× 5).
Rear cover
・ Check if the hole of the rear cover and the USB terminal are aligned.
VAA30001-R.3636.A
- A20 ・ E4100 -
ADJUSTMENT1. Equipment
IBM compatible PC/AT • AC adapter EH-62B • USB cable ( UC-E6)
2. Servicing tools
• Pattern box • Color meter • Luminance meter • Siemens star chart • Calibration software (J65066)
•Adjustment collimator (J63090) or Adjustment firmware
3. Adjustment items and order
1. Lens adjustment
2. AWB adjustment
3. CCD white dot defect compensation
4. CCD black dot defect compensation
5. USB storage information registration
Note) If replacing the lens, CCD, optical filter, CP-1 board, it is necessary to perform the above 1-5
adjustments again. 2-4 adjustments should be made in the above order.
4. Setup
1) System requirements
• Windows® 98 or Me, 2000, XP
• IBM-compatible PC/AT with Pentium or higher processor
• CD-ROM drive
• 3.5-inch 2HD diskette drive
• USB port
• 40 MB or more RAM
• Hard disk drive with 15 MB or more memory space
• VGA or SVGA monitor with 256 or more color display
2) Installing calibration software
• Insert the calibration software installation diskette into the diskette drive.
• Open Explorer.
• Copy "DscCaDI_140" folder of the floppy disk drive in any folder on the hard disk.
VAA30001-R.3636.A
- A21 ・ E4100 -
5. Installing USB driver
If the USB driver is necessary, install Nikon View via CD-ROM packed with the camera.
6. Pattern box
Before using the pattern box, turn its power on to carry out "Aging" approx. 30 minutes: the color temperature
should be 3100 ± 20K by the adjustment with the color meter, and the luminance should be 900 ± 20cd/m2 by the
adjustment with the luminance meter. When using the pattern box and for a while after its power turns off, the
lamp and its surroundings are subject to high temperatures, so care should be taken when handling.
• Procedure for correcting Pattern Box
Note: Be sure to perform the aging correction.
1) Measure the measuring point (center of diffusion plate) with the Color Meter (J63081).
2) Adjust the pattern box so that the color temperature should be 3100±20K by using "VR for adjustment of the
color temperature".
3) Measure the center of the diffusion plate with the Luminance Meter BM-3000 (J63068).
4) Adjust the pattern box so that the luminance should be 900±20cd/m2 by using "Knob for luminance adjustment".
5) Repeat from 1) to 4) So that the color temperature should be 3100±20k and luminance should be 900±20cd/m2.
7. Adjustments required when parts are replaced
Adjustment is necessary. × Adjustment is not necessary.
Lens Adj. AWB CCDDefects
USB Firmwareup
Initial image data
Lens Unit × × ×
Optical filter × × ×
CCD × × ×
CP-1
Power switch
VR for adjustment of the color temperature
Knob for luminanceadjustment
Iris unit
Diffusion plate
Area to be measured
VAA30001-R.3636.A
- A22 ・ E4100 -
8. Connecting the camera to the computer
1) Insert the camera connector of USB cable in the notch of the camera’s USB port.
2) Connect the cable to the USB port on PC.
USBポートへ
USBケーブル
ACアダプター
To USB port
USB Cable
AC Adapter
9. Calibration software
・ Turn on the power switch of the camera.
・When the calibration software starts, the following is displayed on the PC monitor.
VAA30001-R.3636.A
- A23 ・ E4100 -
10. Lens adjustment
※ For the lens adjustment, choose either the infinity adjustment with the collimator or the 1.5-m adjustment with
the adjustment firmware. (However, in case of 1.5-m adjustment, the focus may not be sharp at infinity.)
10-1. Infinity adjustment
[Preparations]
• Turn the power switch of the adjustment collimator (C-DSC) J63090 to on.
• Turn the power switch of the camera to on.
• Siemens star chart
• POWER switch of camera: ON
[Conditions]
• Set the adjustment collimator and the camera (front surface of lens) at the nearest distance between them.
[How to]
• Double-click on "DscCa1Di140".
• Set the siemens star chart so that it comes center of the screen by checking through the viewfinder.
• Click "Focus", then "Yes".
• Lens adjustment value will appear on the screen.
Judgment standard: xd0 = 0±50 , xd7 = 0±50 , xd13 = 0±50, xd19 = 0±50
• Click "OK".
Result of adjustment
カメラ
調整用コリメータ(ジーメンスターチャート内蔵)
Adjustment collimator
(Siemens star chart built-in)
Camera
"Yes"
VAA30001-R.3636.A
- A24 ・ E4100 -
10-2. 1.5-m Adjustment
※ Before performing the 1.5-m adjustment in this machine, write the adjustment firmware on the camera. After
adjustment, be sure to write the product firmware.
Procedure for setting Adjustment firmware
1) Save the adjustment firmware and the product firmware in any folder.
2) Start up "DscCa1Di140" and click on "Firmware" button on the main menu to write the adjustment firmware.
(If the camera is activated after completing writing the adjustment firmware, "SERVICE" is indicated in red
letters on LCD panel.)
3) Follow the instructions of the below [How-to].
4) Start "DscCaDi140" and click "Firmware" on the main menu to write the product firmware.
[Preparations]
• Set the Siemens star chart.
• Turn the power switch of the camera to on.
[Conditions]
• The siemens star chart should be A3-size or larger (Copy and enlarge A4-size siemens chart included in the
service manual for the usage.)
• Illumination over the object should be 400 lux ± 10%
• Set the siemens star chart and the camera (front surface of lens) at 150 cm ± 3 cm distance between them.
[How-to]
• Double click on "DscCa1Di140".
• Set the siemens star chart so that it comes center of the screen by checking through the viewfinder.
• Click "Focus" then "Yes".
• Lens adjustment values will appear on the screen.
Judgment standard: xd0=0 ± 50, xd7 = 0 ± 50, xd13= 0 ± 50 xd19 = 0 ± 50
• Click "OK".
Result of adjustment
カメラ150cm±3cm
ジーメンススターチャート
Siemens star chart
Camera
"Yes"
VAA30001-R.3636.A
- A25 ・ E4100 -
11. AWB adjustment
[Preparations]
• Pattern Box(Color temperature: 3100±20K, Luminance: 900±20cd/m2)
[Conditions]
• Set the pattern box and camera (lens front) at "0cm" distance between them.
Note) Do not allow outside light to enter in.
[How to]
• Double-click on "DscCa1Di140".
• Click "AWB", then "Yes".
• AWB adjustment values will appear on the screen.
Judgment standard: CHECK=128±2, 128±2, 130±30
• Click "OK".
カメラ
バターンボックス
Camera
Pattern Box
"Yes"
Result of adjustment
VAA30001-R.3636.A
- A26 ・ E4100 -
12. CCD white dot defect compensation [Conditions]
• With the lens shutter being closed, read the defect of CCD pixels. Then, make the correction data and rewrite the data by the following procedure.
Correct the upper level of defective 1300 pixels from the brightest number of CCD pixels..
[How to]• Double-click on "DscCa1Di140".• Select "CCD Defect" from Test menu of Calibration Software and click the "OK". Refer to FIG-1.• After adjustment, the adjustment value will appear on the screen. Refer to FIG-2.
13. CCD black dot defect compensation [Conditions]
• Fix the camera so that only the white part of the pattern box should be displayed on the screen. (Do not allow outside light to enter in as much as possible.)• With the lens shutter being opend, read the defect (black dots) of CCD pixels. Then, make the correction data and rewrite the data by the following procedure.
Correct the upper level of defective 30 pixels (black dots in bright place) of CCD pixels.
[How to] • Double-click on "DscCa1Di140".
• Select "CCD Black" from Test menu of Calibration Software and click "OK". Refer to FIG-1.• After adjustment, the adjustment value will appear on the screen. Refer to FIG-3.
カメラ
バターンボックスPattern Box
Camera
(FIG-2)
CCD Defect
CCD Black
(FIG-1)
(FIG-3)
VAA30001-R.3636.A
- A27 ・ E4100 -
14. USB storage information registration
USB storage data is important when the camera is connected to a computer via a USB connection.
If there are any errors in the USB storage data, or if it has not been saved, the USB specifications will not be
satisfied, so always check and save the USB storage data.
[How to]
• Connect the camera to a computer.
• Double-click on the "DscCa1Di140".
• Click on the "Get" button in the USB storage window and check the USB storage data.
VID: NIKON
PID: NIKON DSC E4100
Serial:
Rev. : 1.00
• Check the “Serial” in the above USB storage data. If the displayed value is different from the serial number
printed on the base of the camera, enter the number on the base of the camera, and click the "Set" button.
• Check VID and Rev. entries in the USB storage data. If any of them are different from the values in 3. above,
enter the details of 3. and click the "Set" button.
VAA30001-R.3636.A
- E1・ E4100 -
ø
ø
ø
ø
øøøøø
VAA30001-R.3636.A
- E2・ E4100 -
VAA30001-R.3636.A
- E3・ E4100 -
VAA30001-R.3636.A
- E4・ E4100 -
VAA30001-R.3636.A
- E5・ E4100 -
VAA30001-R.3636.A
- E6・ E4100 -
VAA30001-R.3636.A
- E7・ E4100 -
VAA30001-R.3636.A
- E8・ E4100 -
VAA30001-R.3636.A
- E9・ E4100 -
総合結線図
OVERALL WIRING
VSS
NCNC VCOM
GPCK
STBYB
GSRT
STH
RIT
STBYB
VGL
VC1
VC2
GRES
VDD
VGH
NC CP POL
VSH
D00
D03
D04
D01
D02
VRH
VRL
VBC
VDD
VSS
STB
D05
CLK
WHITE
JW505 LED_C
JW504 LED_A
GRAY
JW601 LED_A
JW602 LED_C
CARD/WP
DATA1
DATA0
DATA2
CARD
COMM
AND
DATA3
CLOC
KVSS
VSS
VDD
WP
ZAV_JACK
USB_VDDUSB D(-)
GNDUSB D(+)
AUDIO_OUT
GNDVIDEO_OUT
W1400 XAN (RED)
JW502 BAT-(BLACK)
JW501 BAT+ (RED)
W1600 TRG (GRAY)
FOCUS_ST(B)FOCUS_ST(A)
FOCUS_ST(-A)
Z_PULSE_PI1
SH1
ZOOM_DC1ZOOM_DC2
ZOOM_LEDZ_PULSE_PI2
PIV
FOCUS_LEDFOCUS_PI
PIVZOOM_PI
FOCUS_ST(-B)
Z_PULSE_LED
SP- (RED)
SP+ (BLACK)
W1500 XKT(BLACK)
DP1DP2
SH2
SCAN
IN0E
SCAN
IN1E
SCAN
OUT4
SCAN
IN2E
PW_LED
AL3.2V
NC
MIC (WHITE)
GND (BLACK)
SCAN
OUT2
SCAN
OUT3
SCAN
IN0C
SCAN
OUT0
SCAN
IN3C
SCAN
IN2C
SCAN
OUT1
SCAN
IN1C
SCAN
OUT3
SCAN
IN2D
SCAN
IN3D
SCAN
IN4C
SCAN
IN4D
SCAN
IN1
SCAN
IN3
SCAN
IN3
SCAN
IN4
SCAN
IN2
SCAN
IN2
AF.LE
D(G)
SB.LE
D(R)
AL3.2V
SCAN
IN0D
SCAN
IN1D
SPEAKER
-4
-2
-3
-6
-5
GNDGND
GND
GNDGND
-1 GND
TB1
CP1
LED
USB
LCD PANEL SD
&VIDEO
FLASH
LENS
REFLECTOR
MIC
RELEASEUNIT
BACK SWUNIT
CN110
CN171
CN143
CN951
CN301
CN302
181716151413121110987654321 333231302928272625242322212019 121110987654321
8
7
6
5
4
3
2
1
19
18
17
16
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
7654321 242322212019181716151413121110987654321
BATTERY
(DMA)(CAA)(SYA)(PWA)
W1-67400/SX795-JNK
MODEL: E4100OVERALL WIRING
VAA30001-R.3636.A
- E10 ・ E4100 -
総合ブロック図
OVERALL BLOCK DIAGRAM
SDRAM
IC103SD(0:31)128Mbit
16MbitFLASH(NOR)
FLASH(NAND)128Mbit
IC121
D(0:15)
FD(0:7)
A(1:20)
CKIN1CKIN2
FSC4
IC111CLOCK GENERATOR
28.63636MHzX1101
CN143SD CARD
IC181AUDIODRIVER
FD(0:4)
IC172AMP
LCD MONITOR
LCDLBRT
LCDVCO
MD
PADYOU
T
LCDPOL
LCDD
(0:5)
LCDCLK
LCDTIM
INGPULSEX8
IC152VIDEO AMP
VOUT
CN110USB/VIDEO
4MHzX3001 X3002
32.768KHz
MRSTZTESTPLLEN
CLKSEL0
SCK
SDISDOSREQ
CN301
IC3018bit Micro Processor
LENS DRIVERIC951
CN951 LENS
3
PICTL
ZMIN1,2
ZPULSE1,2
ZRESET
LENS BLOCK
FIN(1:4)SIN1,2
IIN1,2
Z3001BACKUP
AD(0:9)
ADCK
TGVD,TG
HD
CCDC
K
CCDSD
CCDEN
XV(1:6)
SUBG
T
XSG(1A,2A
,1B,2B
,3)
XSUB
CCD BLOCK
IC101ASIC
4M PixelIC903
V. Driver
IC901IC902
CCDCDS/AGC/AD-C
H. Driver
USBD+
PADAOU
TASICAIN
AUDIO
CONTRO
LSIGN
ALSX5
USBD-
Ni-MH
CP1
LCD BACKLIGHT
DC/DCCONVERTER
ELECTRONICFLASH
VDDREGULATOR
IC302
LENSDC/DC
CONVERTER
IC955
CN302BACK SW UNIT
RELEASE UNIT
MODEL: E4100BLOCK DIAGRAM: OVERALL
BL ON
MIC
SPEAKERAUDIO OUT
IC106D-FF
PWA BLOCK
SYA BLOCK
VAA30001-R.3636.A
- E11 ・ E4100 -
ASIC ブロック図ASIC BLOCK DIAGRAM
DIGITALCLAMP
SIGNALPROCESSOR
AF,AE,AWB
SRAM SRAM
D/ACOMPOSITEVIDEO
NTSC/PAL
ENCODERSRAM
BUS BUS
DIGITALI/F
A/D
D/A
TGCLKGENPLL
SDRAMCONTROLLER
JPEGCONTROLLER
CCD98MHz4fsc
36MHz
72MHz
ARM
UART
USB
SD
PWM
SIOIC301MICROPROCESSOR
EXT PORT(LENS DRIVER)
PIO
BUS I/F
FLASH(NOR)
SDRAM
CCDBLOCK
IC101 ASIC
RGB6bit DATA
CCDDRIVER
AUDIODRIVER
SD CARD
USBCONNECTOR
MODEL: E4100BLOCK DIAGRAM: ASIC
FLASH(NAND)
VAA30001-R.3636.A
- E12 ・ E4100 -
CCDブロック図CCD BLOCK DIAGRAM
LENS
CCD
EF
XV2XV3
XV5
XSG1A
XV6
+12V(A)-8.0V(A)
MN39483PJJ
VDD
VPT
H1
RG
H2
VOUT
O_LPF
IC901
IC903
CH1,C
H2,C
H3,C
H4,C
H5
IV1,IV2,IV3,IV4,IV5,IV6
ISUB
Q9001
XV1
XSG2A
SUB
V.DRIVER
AN20101A
XSG1B
XSG3
SUBGT
IC902
CDS,A/D
C
AD9948KC
PZRL
D2~
D11
31
32
33
AD0
AD9
ADCK
CCDCK
CCDSD
CCDEN
VCC
IC904REG
.TK11130C
S
3.0V+3.45V(A)
VDD3
TOCP1(D
MA)
IC101
ASIC
10
13
17
18
11
1~8
15
19
1,2,21,23,24
20,22,25,26,27,28
3
25
92-4.7-13
27
14,15,21
8
+12V(A)
+3.45V(A)
-8.0V(A)
6,184,5
24, 37, 6
TGVD
TGHD
34, 35
17,22
H.DRIVER
14SUBC
16 HL
XV4
XSUB
XSG2B
V1,V2,V3A,V3B,V4,V5A,V5B,V6
BLOCKDIAG
RAM
:CCD
MODEL:E4100
9-16
VAA30001-R.3636.A
- E13 ・ E4100 -
レンズ駆動ブロック図
LENS DRIVE BLOCK DIAGRAM
IR/SH DRIVER
IN9
IN10
IN11
IN12
OUT9
OUT10
OUT11
OUT12
UNREG
5
6
ZM.MOUT6
OUT5 ZOOM_DC1
ZOOM_DC2IN6
IN5
ZOOM DRIVER
LB8649WIC951
FOCUS DRIVER
IN1
IN2
IN3
IN4 FOCUS_ST(-B)
FOCUS_ST(B)
FOCUS_ST(-A)
FOCUS_ST(A)OUT1
OUT2
OUT3
OUT4
FC.M
17
19
18
16
ZPLUSE1
ZPLUSE2
PICTRL(IC301 23pin)
VDD3
FOCUS_PI
CN951UNIT LENS
SIN1(IC106 12pin)
SIN2(IC106 15pin)
ZPULSE1(IC301 16pin)
ZMIN1(IC301 47pin)
ZMIN2(IC301 46pin)
FIN1(IC106 2pin)
FIN2(IC106 5pin)
FIN3(IC106 6pin)
FIN4(IC106 9pin)
FPIOUT(IC101 231pin)
DP2
DP1
SH2
SH1 4
3
2
1 IR.MIIN1
(IC106 16pin)IIN2
(IC106 19pin)
9
8
14
ZOOM_PI
11
Q9509
IC955L9551D9551C9554
SW REG.BOOST4.35V
ZRESET(IC301 58pin)
Q9501
Q9502ZPULSE2
(IC301 59pin)
PIV12, 15
10
10
7
13
SH.M
5
6
1
2
3
4
9
10
11
12
27
26
37
36
35
34
33
31
30
28
MODEL: E4100BLOCK DIAGRAM: LENS
VAA30001-R.3636.A
- E14 ・ E4100 -
POWER ブロック図POWER BLOCK DIAGRAM
IC501
SWITC
HING
CONTROL
FA7709R
T5001,Q5001
CONVERTO
RTRANS
IC955
STEPUP
CIRCUIT
Q9551,L9551
L5009,Q5003
STEPUP
CIRCUIT
L5004,Q5002
STEPDOWN
CIRCUIT
L5011,Q5009
STEPDOWN
CIRCUIT
+12.0V(A)
-8V(A)
+3.45V(A)
LED_A
VDD3
BOOST4.35V
OUT1
OUT6
OUT2
OUT3
L5007,Q5010
STEPUP
CIRCUIT
OUT4
L5008,Q5013
STEPUP
CIRCUIT
CURRENT
DETEC
TOR
CIRCUIT
IC502REG
.
IC503
REG
ULLATO
R
OUT5
LCDAN
LCDCA
CNT4
9
CNT1
6
CNT2CNT3
CNT6
ON/OFF
78
1131
1617
18
19
CNT5
10
1520
34
MODEL:E4100
BLOCKDIAG
RAM
:POWER
VRVR501
Q5024
PON
AFLEDAN
PAON2
VDD1.7
+15V(L)
+5V(L)
PAON
LCDON3
LCDON
BLON
TODMA(MAIN)
TODMA(MAIN)
TODMA(MAIN)
TOLCD
BACKLIGHT
TOTB1
Q5011
Q5022
Q5014
VAA30001-R.3636.A
- E15 ・ E4100 -
SYSTEM ブロック図SYSTEM BLOCK DIAGRAM
BACKUP CTL
565554
44
3130
43
4647
5916
10
7
8
11
226339
42
511921
35
2 6 32
17
29
37
9
13
56781 2 3 4
38
6257
481
41
334
45
36
50
58
X3001
X300232KHZ
4MHZ
SCAN OUT0
18
SB_LED (R)AF_LED (G)
ZM IN1ZM IN2
ZPULSE2ZPULSE1
XIN
XOUTXCOUT
XCIN
VMONITCHG ON
IC3018bit MICROPROCESSOR
SCAN IN0SCAN IN1SCAN IN2
SCAN OUT1
SCAN OUT2
PLLENBEEP
LCD ON2
PA_ONP ON
LCD ONSELF LED
VMONITCHG
BOOST4.35V
SREQ
P ONPA ON
SPORTSNIGHTVIEW
OK
SCENE LANDSCAPEPORTRAIT
SET UP
PW_ON
LCD ON
PW_LED
1stSI
RESET
BAT OFF
64 BATTERYLI
IC302BATTERYBACKUP
BAT
OFF
AL3.2V
UNREG VDD
RESET
ALWAYS3.2V
IC304RESET IC
4 3
1 2
OUT
VDD
VSS
BACK UP
SO
AUTO
SCAN IN3SCAN IN4
2nd
MOVIE
AV REF ONAVREF
SW3.2V
Q3001
TELE MENUDEL SCAN OUT3
VDDVDD
WIDE
TEST
PW_TEST
PLAY
RIGHTLEFT UP DOWN
CN301CN302
CN301CN302
-
AVJACK SCAN OUT4
SCK
24
34
BLON
MODEL: E4100BLOCK DIAGRAM: SYSTEM CONTROL
BL_ON
ASIC TEST28
60MAIN RESET
CARD
ZRESET
5212
1523
CLKSEL0COMREQ
USB CONNECTPICTL
ZM IN1ZM IN2
ZPULSE2ZPULSE1
TO DMA(MAIN)
TO DMA (MAIN)
PLLENBEEP
LCD ON2
14LCD ON3 LCD ON3SREQSDOSDISCK
ZTESTMRSTZCARD
ZRESET
CLKSEL0COMREQUSB_CNT
PICTL
Z3001
Q3002
Boost4.35V
49SELF LEDPA ON249PA ON2
UNREG
TO DMA (LENS)
VAA30001-R.3636.A
- E16 ・ E4100 -
PWA 回路図 (ストロボ回路図 )PWA CIRCUIT DIAGRAM(STROBE CIRCUIT DIAGRAM)
WT
GR
BAT+JW501
W1400
W1600
W1500
(K)
(K) (400V
)
BAT-JW502
JW504LED_A
IN5+
IN4-
IN5-
IN6-
FB5
FB4
FB6
IN3-
VREGIN2-
IN1-
FB2
FB1
FB3
VCC
CPST
CTST
VBAT
CT
RT
VREF CP
JW505LED_C
PGND
2
CNT4
CNT3
CNT2
PVCC
SEL3
CNT6
CNT5
CNT1
OUT6
OUT2
OUT4
OUT3
OUT0
OUT1
OUT5
CS5
CS6
SEL2
CS1
CS2
ON/OFF
GND
CS4
CS3
PGND
1
2125
1608
2.0A 32V
1608
2.0A 32V
1608
2125
2125
D
2012
POS-CA
P2.0A 32V1608
1608
G
S
1608
H=0.9
5
2016
2016
3216
2125
3216
3216
1608
1608
2.5A 32V1608
D63CB
D52LC
S D
G
D
S
G
1608
1608
D52LC
16081608
3216
3216
1608
32163225
3216
3216
POS-CA
P
3216
CH1 <FOR ANALOG>
<FOR DIGITAL 3.25V>
<FOR DIGITAL POWER SUPPLY>
CH2
CH6
POS-CA
P
<FOR LCD 15.0V>
<FOR DIGITAL 1.7V>
CH4
CH3
CH5 <FOR BACK RIGHT>
RED
2125
XKT
XAN
TRG
RED
H=1.2OM/ORLL57Z
H=1.2OM/ORSO08X1SANZ
OM/ORLIV006HZH=5
H=3
GRAY
BLACK
H=1.7
OM/ORTR01Z
OM/ORD
D58Z
NEW
H=1.9
OM/ORZL17B0120GZH=4.8
OM/ORDD30HVZ
OM/ORTR15Z
OM/ORDD44Z
OM/ORTR02Z
BLACK
FB
H=1.2
H=2
POS-CA
P
OM/ORTR16Z
OM/ORTR25Z
EXT
GND
H=1.3
VDDCE
OM/ORZL51B2350GZH=3.0
H=2
NPVOUT
3.4V
VCONTVIN
REG
IN OFF
GND
H=1.8
H=1.8
(EMD2)
H=2OM/ORLL57Z
OM/ORTR25Z
OM/ORLL47ZH=3 2SA2018
DTC114E
POS-CA
P
H=1.2
H=1
OM/ORIC48FJT1Z
H=2.0OM/ORLL84Z
H=2OM/ORLL57Z
2SA1774VOUT
2SA1774
VIN
GND
DTC144E
POS-CA
P
OM/ORLL84ZH=2.0
DTC144E
DTC144E
2SA1774
LCD_AN
LCD_CA
FLASH REFLECTOR
DS
G
3
290V
BC
E
BCE
DB320C
EDK3
16BJ475K
D-T
DB320C
EDK3
16BJ225K
D-T
L5015 F5003
F5004
D9551L9551
T5402
D5404
D5408
R5426
R5418
D5405
C5410
Q5409
R5425
R5423
R5424
C5409
R5422
C5411
R5408
R5406C5403
R5432
D5402D5403
R5419
R5409
C5420
C5404
C5401
T5401
C5406
Q5407
R5414
Q5410 Q5411
R5429
R5433
R5430R5431R5413
R5420
R5417
Q5401
Q5405
R5401
Q5402
D5407
C5407
C5413
RB504
L5014
C9551
R9554
R9553
R9552
C9554
R9551
Q9552
R5117
C9553C9
552
Q9551
IC955
L5016
T5001
D5010
C5023
F5001
C5064
Q5001
L5002
L5001
RB502
R5022
R5025
C5035
IC503
C5037
R5024
C5033
R5112
Q5018
R5113
C5031
C5032
C5034
C5036
R5023
D5001
RB505
R5097
C5079
C5001
C5002
C5020
IC501
C5019
C5018
C5021
C5013
C5016
R5011
C5017
VR501
D5013
F5002 L5009
L5004
RB506
RB501
R5099
C5043
D5005
D5004
D5008
RB503
R5026
Q5023Q5020
R5074
C5038
C5075
Q5024
R5072
R5071
C5078
R5084
Q5002
R5035
R5034R5
033
Q5003
C5014
C5008
C5009
C5010
C5011
C5006
C5012
C5022
L5007
C5080
L5011
C5048
R5114
D5006
R5042
C5053
C5047
C5052
Q5010
Q5009
C5068
R5054
Q5011
R5053
C5069
C5070
Q5014IC502
R5052
R5051
R5044
R5045
R5043
L5008
R5055
R5063
R5068
R5062
C5061
Q5022
R5091
R5090
R5067
D5007
C5062
R5061
Q5013
F47K2R0D3LTND
F47K2R0D3LTND
SD833-04SC10;M
CMC0
1MA
2SD1
9
470K
;1/16J
56;1/16J
S6A37
0.047;350H
CY25BAJ-8F
100K
;1/8J-X
33;1/16J
220;1
/16J
0.033;F
220K
;1/8J-X
0.01;630H
120;1/16J
100;1/16J0.068;B
3.9K;1/1
6D
F1P8RR264M-400
82K;1/1
6D
1.2K;1/1
6J
4700P;B
1000P;B
47;6.3-V
0.01;B
3LN01S
1K;1/16J
2SA1745 DTC144EM
6.2K;1/1
6D
100K
;1/16J
4.7K;1/16J100K
;1/16J
10K;1/1
6J
10K;1/1
6D
10M;1/8
F-X
DTC123JE
CPH5504
1K;1/16J
DTC114EM
DAN2
22
6800P;B
6800P;B
1M
10;6.3B
560K
;1/16D
130K
;1/16D
15K;1/1
6D33;8-V
390K
;1/16D
DTC144EM
0;1/16Z
330P
;B10;6.3B
FDC633N
XC9104D095MP
10;M
MA2S
D19
33;10
-V
F47K2R0D3LTND
1;B
CPH3413
47;K
100;K
18
2.2K;1/1
6J
13K;1/1
6D
0.1;B
TK11134CS
1;B
150K
;1/16D
1;B
100K
;1/16J
2SA1774(R)
82K;1/16J
2.2;16
B
10;B
10;10
B
2200P;B 0;1
/16Z
HN2D01JE
1M
910;1/16J
0.01;B
0.01;B
1000P;B
0.1;B
2200P;B
6800P;B
4700P;B
150P;CH
1;B
9.1K;1/16D
0.47;B
3.3K
MA2SD19
F47K2R5D3LTND
4.7;M
10;M
47K
750
11;1/16D
33;8-V
MA2Z720
MA22D1
5
SD833-04SC
75
470;1
/16D
EMH10EMD2
56K;1/1
6J
2200P;B
47;6.3-V
EMF21
2.2K;1/1
6J100K
;1/16J
2200P;B
0;1/16
Z
CPH3313
5.36K
;1/16D
12K;1/1
6D
0;1/16
Z
CPH3409
FA7709R-H1
6800P;B
0.033;B
0.1;B
0.1;B
0.022;B
0.033;B0.1;B
6.8;M
1;B
1;B
10;M
33;8-V
47K;1/16J
MA22D1
5
56K;1/1
6J
4700P;B
2200P;B
4.7;B
MCH5809
MCH3319
1;B
150K
;1/16D
EMF18
1K;1/16J
1;16B
1;B
EMF18XC6202P502MR
22K;1/1
6J100K
;1/16J
11.8K
;1/16D
16.9K
;1/16D
0;1/16
Z
6.8;M
10.7K
;1/16D
45.3;1/1
6D
33K;1/1
6J
10K;1/16D
2.2;B
EMF18
22K;1/1
6J
100K
;1/16J
100K
;1/16J
MAZS
1600ML
4700P;B
1K;1/16J
MCH5809
16V
6.3V
16V
16V
6.3V
6.3V
6.3V
6.3V16
V
6.3V
1AV4L26B3450G
1AV4L17B0160N
1AV4L17B0200G
1AV4L26B3450G
TFDC633N----K
QXC9104D095MP
1AV4L2FM100MG
1AV4L51B6070G 1AV4L2FB470KG
1AV4L2FB101KG
QTK11134CS--J
CK1C
105K
GWBN
G
1AV4L2JQ6R8MG
CK1C
475K
SVBN
G
TMCH3319----P
1AV4L2JQ6R8MG
CK1C
225K
SVBN
G
BOOST4.35V
UNREG
VMONIT
TRIG
STOP
RDY
CHG
PAON
+3.45V(A)
-8.0V(A)
+12V(A)
AFLED_AN
AFLED_CA
SELFLED
VDD3
PAON2
+5V(L)
LCDON
+15V(L)
PON
VDD1.7
LCDON3
BLON
1
2
1
8765
4 3 2 1
3
2
13
254
2 1
543
6 5 4
321
54
3 2 1
1
5
4 3
2
13
2
6
5
7
8
4
5
43
2
1
1
2
3
4
5
404142434445464748
32
33
34
35
36
373839654
3 2 16 5 4
321
3
2
1 6
5
4
6
7
8
9
10
11
12
13 14 15 16 17 18 19 20 21 22 23 24
25
26
27
28
29
30
31
5 4
321
3
2
1 6
5
4 2
3
2
1 6
5
4
1
3
2
1 6
5
4
3
5 4
321
SW REG.
SWITCHING CONTROL
REG.
TO TB1
TO DMA(MAIN)
TO DMA(LENS)
TO DMA(MAIN)
TO LCD BACK LIGHT
TO DMA(MAIN)
!
P1-67400/SX795-JNK
PWA
!
!
!
CIRCUIT DIAGRAM: CP1(PWA)
MODEL: E4100
WHITE
RED
VAA30001-R.3636.A
- E17 ・ E4100 -
FUSE ARRANGEMENT (CP1 PCB)
F5001F5004F5002
F5003
Fuse Function Phenomenon when it has blown out singly
Rating
F5001 Used to protect the unit when the DC/DC converter circuit malfunctions.
The power of the camera is not turned on.
2.0A 32V
F5002 Used to protect the unit when the DC/DC converter circuit malfunctions.
The power of the camera is not turned on.
2.5A 32V
F5003 Used to protect the unit when the lens system DC/DC converter circuit malfunctions.
The power of the camera is not turned on.
2.0A 32V
F5004 Used to protect the unit when the speed light charging circuit malfunctions.
The condenser is not charged.
2.0A 32V
VAA30001-R.3636.A
- E4100 -
The contents of inspection standards and tools for E4100
[1] Inspection standards ................................................................................................................................. R1 to R7
[2] Tools ......................................................................................................................................................... T1 to T3
VAA30001-R.3636.A
- T1・ E4100 -
[2] 工具一覧表 Tool List
※:新規工具
※:New tool
工具番号
Tool No.
J63080
J63080A
J63081
J63068
名 称
Name
パターンボックス LV-1450DC
Pattern Box LV-1450DC
交換用ハロゲンランプ (LV-1450DC用 )
Spare Harogen Lamp (For LV-1450DC)
カラーメータ (ミノルタカラーメータⅢ F)
Color Meter(Minolta Color meterⅢ F)
輝度計 BM-3000
Luminance Meter BM-3000
備 考
Remarks
共通 (E4300, E3500,
E3100, E2100, E5400,
E3700, E3200, E2200,
E8700, E4100)
Common(E4300, E3500,
E3100, E2100, E5400,
E3700, E3200, E2200,
E8700, E4100)
LV-1450DC
Exclusive
共通
Common
共通
Common
POWER
BM-3000
VAA30001-R.3636.A
- T2・ E4100 -
※:新規工具
※:New tool
工具番号
Tool No.
J65066
J63090
サービスマニュアル添付
Attached in
Service Manual
名 称
Name
キャリブレーションソフト
Calibration Software
コリメータ (C-DSC)
Collimator (C-DSC)
ジーメンスチャート
Siemens chart
備 考
Remarks
共通 (E995,E775,E885
E5000, E2500, E4500
E5700, E4300, E3500
E3100, E2100, E5400
E3700, E3200, E2200
E8700, E4100)
Common(E995,E775,E885
E5000, E2500, E4500
E5700, E4300, E3500
E3100, E2100, E5400
E3700, E3200, E2200
E8700, E4100)
共通
Common
共通
Common
※
VAA30001-R.3636.A
- T3・ E4100 -
ジーメンススターチャート