Upload
others
View
2
Download
5
Embed Size (px)
Citation preview
1
The information contained in this proposal is proprietary of BENTLEY and is not to be disclosed to any third party without BENTLEY’s prior written consent.
1
OpenPlant Water/Waste Water CCK
BENTLEY 软件(北京)有限公司
2020/12/21
12/21/2020
The information contained in this proposal is proprietary of BENTLEY and is not to be disclosed to any third party without BENTLEY’s prior written consent.
1
目 录
1. 文档版本记录 ......................................................................................................................... 1
2. 安装要求 ................................................................................................................................. 2
2.1 系统要求(推荐配置) ....................................................................................................... 2
2.2 OpenPlant PID ................................................................................................................. 2
2.3 OpenPlant Modeler ......................................................................................................... 3
3. PID 图例说明 .......................................................................................................................... 4
3.1 为水行业增加的设备图例 ............................................................................................. 4
3.2 为水行业增加的管件图例 ............................................................................................. 6
3.3 为水行业增加的仪表图例 ............................................................................................. 9
4. 等级库说明 ........................................................................................................................... 10
4.1 T1 ................................................................................................................................... 10
4.2 UPVCSPEC ...................................................................................................................... 10
5. OPM 参数化设备 .................................................................................................................. 11
5.1 闸门 ............................................................................................................................... 11
5.2 启闭机 ........................................................................................................................... 13
5.3 沉砂器 ........................................................................................................................... 14
5.4 清污机 ........................................................................................................................... 15
5.5 刮泥机 ........................................................................................................................... 16
5.6 排污泵 ........................................................................................................................... 17
5.7 搅拌机 ........................................................................................................................... 18
5.8 鼓风机 ........................................................................................................................... 19
6. OPM 参数化阀门 .................................................................................................................. 20
6.1 微阻缓闭蝶式止回阀 ................................................................................................... 20
6.2 带锁平衡阀 ................................................................................................................... 22
6.3 快开排泥阀 ................................................................................................................... 23
6.4 明杆楔式闸阀 ............................................................................................................... 25
6.5 电磁阀 ........................................................................................................................... 27
6.6 刀闸阀 ........................................................................................................................... 29
12/21/2020
The information contained in this proposal is proprietary of BENTLEY and is not to be disclosed to any third party without BENTLEY’s prior written consent.
2
6.7 旋启式止回阀 ............................................................................................................... 30
6.8 升降式止回阀 ............................................................................................................... 32
6.9 球阀与手柄 ................................................................................................................... 34
6.10 活塞式减压阀 ........................................................................................................... 36
7. 执行机构及其他 ................................................................................................................... 39
7.1 D941X 电动执行机构 ................................................................................................... 39
7.2 D943H 电动执行机构 ................................................................................................... 40
7.3 手柄 ............................................................................................................................... 42
7.4 电动刀闸阀 ................................................................................................................... 44
7.5 法兰限位伸缩接头 ....................................................................................................... 48
7.6 不锈钢波纹管 ............................................................................................................... 51
Appendix 1: Spec 数据库中相关表与字段说明 .......................................................................... 53
Appendix 2: China First 使用工具说明 ......................................................................................... 54
1
The information contained in this proposal is proprietary of BENTLEY and is not to be disclosed to any third party without BENTLEY’s prior written consent.
1
12/21/2020
1. 文档版本记录
版本 日期 作者 备注 10.08.0051 2020-12-21 单鹏/武博 首次发布
2
The information contained in this proposal is proprietary of BENTLEY and is not to be disclosed to any third party without BENTLEY’s prior written consent.
2
12/21/2020
2. 安装要求
2.1 系统要求(推荐配置)
CPU:2GHz X64 Processor 或者更高,四核或者八核,Intel i7-3740QM 同等配置或以上
内存:8G,建议 16G 以上
硬盘:500G 以上,建议系统盘采用 SSD 固态硬盘
显卡:显存 2G 或者更高,NVIDIA Quadro K2000M 系列及同等配置型号以上(支持双
屏优先)
操作系统:Windows 7 X64 专业版以上,建议 Window 10 专业版或企业版
说明:对于台式机,显卡支持双屏显示,同时外配外接显示器将大大提高工作效率
2.2 OpenPlant PID
提前安装 OpenPlant PID Update 8(oppid10080051zh) ,中文版/英文版均可。以中文版为
例。安装后,选择“WWT_WorkSpace”环境。
3
The information contained in this proposal is proprietary of BENTLEY and is not to be disclosed to any third party without BENTLEY’s prior written consent.
3
12/21/2020
2.3 OpenPlant Modeler
提前安装 OpenPlant Modeler Update 8(opm10080051zh) ,中文版/英文版均可。以中文版为
例。安装后,选择“WWT_WorkSpace”环境。
4
The information contained in this proposal is proprietary of BENTLEY and is not to be disclosed to any third party without BENTLEY’s prior written consent.
4
12/21/2020
3. PID 图例说明
3.1 为水行业增加的设备图例
• 机械计量泵
• 气动泵
• 化学注入隔膜泵
• 立式切碎泵
• 立式涡轮泵
• 潜水泵
• 齿轮泵
• 计量泵
• 往复泵
• 螺旋泵
• S 螺杆泵
5
The information contained in this proposal is proprietary of BENTLEY and is not to be disclosed to any third party without BENTLEY’s prior written consent.
5
12/21/2020
• 离心式多级鼓风机
• 离心式单级鼓风机
• 双往复式压缩机
• 离心式压缩机
• 风扇
• 鼓风机
• 空气压缩机
6
The information contained in this proposal is proprietary of BENTLEY and is not to be disclosed to any third party without BENTLEY’s prior written consent.
6
12/21/2020
• 水闸
• 滑动门
• 快速闸门
• 起重机
• 回转格栅
• 启闭机
• 撇水器
• 阶梯格栅
• 集油管
• 管式曝气器
• LC 曝气器
• TOS 曝气器
• 板框
• 离心脱水机
• 刮泥机
• 刮油刮泥机
• 冷却塔
• 浆式搅拌机
• 潜水搅拌机
• 浮筒搅拌机
• 自卸卡车
• 纤维球
• 压力溶气罐
• 水锤消除器
3.2 为水行业增加的管件图例
7
The information contained in this proposal is proprietary of BENTLEY and is not to be disclosed to any third party without BENTLEY’s prior written consent.
7
12/21/2020
• 水泵阀
• 节流阀
8
The information contained in this proposal is proprietary of BENTLEY and is not to be disclosed to any third party without BENTLEY’s prior written consent.
8
12/21/2020
• 排放消音器
• 过滤器
• 火焰阻火器
• 在线静态混合器
• 扩散器
• 带排放过滤器
• 机械清洁过滤器
• 快拆
• 脉冲缓冲器
• 放空到大气
• 蒸发器
• 蒸汽加热器
• 观察孔
• 气隙
• 活接头
9
The information contained in this proposal is proprietary of BENTLEY and is not to be disclosed to any third party without BENTLEY’s prior written consent.
9
12/21/2020
3.3 为水行业增加的仪表图例
• 环形密封
• 隔膜密封
• 卫生密封
• 校准柱
10
The information contained in this proposal is proprietary of BENTLEY and is not to be disclosed to any third party without BENTLEY’s prior written consent.
10
12/21/2020
4. 等级库说明
修复部分内容
• 所有 MAIN_SIZE, RUN_SIZE 字段公制单位统一不加 mm,不带小数点,如 100, 150…
• 法兰、螺栓、垫片等紧固件 Rating 字段统一使用 PN 制,不使用 Mpa 制,
如 PN16, PN40, PN160,对照关系如下
公称压力 MPa
0.6 MPa 1.0 MPa 1.6 MPa 2.0 MPa 2.5 MPa 4.0 MPa 5.0 MPa 6.4
MPa 10.0 MPa - 15.0 MPa 25.0 MPa 42.0 MPa
公称压力 PN PN6 PN10 PN16 PN20 PN25 PN40 PN50 PN64 PN100 - PN150
PN250 PN420
4.1 T1
安装包附带了名为 T1 的管道等级库作为测试之用,具体项目还需根据项目需求制定相应
的等级库.
4.2 UPVCSPEC
增加了水行业需要的 PVC 管件增加了水行业需要的 PVC 管件,如 GB/T 10002.1-2006
11
The information contained in this proposal is proprietary of BENTLEY and is not to be disclosed to any third party without BENTLEY’s prior written consent.
11
12/21/2020
5. OPM 参数化设备
WWT CCK 中新增了水处理相关的设备部件和阀门等,用户可以使用这些设备和阀门进行
建模。对于设备,可到新添加的“WWT Equipment”工具栏中去选取; 对于阀门和执行机
构,需要到相应类别的阀门和执行机构中去选取。
设备的布置使用如下工具,依次为:闸门、启闭机、沉砂器、清污机、刮泥机、排污泵、
搅拌机、鼓风机。
各个设备的布置界面及效果如下:
5.1 闸门
12
The information contained in this proposal is proprietary of BENTLEY and is not to be disclosed to any third party without BENTLEY’s prior written consent.
12
12/21/2020
13
The information contained in this proposal is proprietary of BENTLEY and is not to be disclosed to any third party without BENTLEY’s prior written consent.
13
12/21/2020
5.2 启闭机
14
The information contained in this proposal is proprietary of BENTLEY and is not to be disclosed to any third party without BENTLEY’s prior written consent.
14
12/21/2020
5.3 沉砂器
15
The information contained in this proposal is proprietary of BENTLEY and is not to be disclosed to any third party without BENTLEY’s prior written consent.
15
12/21/2020
5.4 清污机
16
The information contained in this proposal is proprietary of BENTLEY and is not to be disclosed to any third party without BENTLEY’s prior written consent.
16
12/21/2020
5.5 刮泥机
17
The information contained in this proposal is proprietary of BENTLEY and is not to be disclosed to any third party without BENTLEY’s prior written consent.
17
12/21/2020
5.6 排污泵
18
The information contained in this proposal is proprietary of BENTLEY and is not to be disclosed to any third party without BENTLEY’s prior written consent.
18
12/21/2020
5.7 搅拌机
19
The information contained in this proposal is proprietary of BENTLEY and is not to be disclosed to any third party without BENTLEY’s prior written consent.
19
12/21/2020
5.8 鼓风机
20
The information contained in this proposal is proprietary of BENTLEY and is not to be disclosed to any third party without BENTLEY’s prior written consent.
20
12/21/2020
6. OPM 参数化阀门
以下对 WWT CCK 中实现的自定义阀门部分所使用的规范,型号以及在 Open Plant Modeler
中界面的放置等进行详细说明。
6.1 微阻缓闭蝶式止回阀
参照规范《阀门产品样本 下 第 4 版》第 300 页,HH49X 型 PN10~25。
阀门 EC Class 名字 MRSC_BUTTERFLY_CHECK_VALVE。
Spec 表 VLVCNTFL 的 COMP_LEN 列对应了规范中的 L 参数;表 VLVCNTFL 的
OPERATING_HEIGHT 列对应了规范中的 H 参数。Spec 表说明参见附录。
在 Open Plant Modeler 中,“阀门类”选择“控制阀”,并选择“微阻缓闭蝶式止回阀”
进行布置。
21
The information contained in this proposal is proprietary of BENTLEY and is not to be disclosed to any third party without BENTLEY’s prior written consent.
21
12/21/2020
布置结果如下所示:
22
The information contained in this proposal is proprietary of BENTLEY and is not to be disclosed to any third party without BENTLEY’s prior written consent.
22
12/21/2020
6.2 带锁平衡阀
参照规范《阀门产品样本 下 第 4 版》第 1004 页,SP15F 型 PN10,16。
阀门 EC Class 名字 LOCKED_BALANCE_VALVE。
Spec 表 VLVCNTFL 的 COMP_LEN 列对应了规范中的 L 参数;表 VLVCNTFL 的
OPERATING_HEIGHT 列对应了规范中的 H 参数。Spec 表说明参见附录。
在 Open Plant Modeler 中,“阀门类”选择“控制阀”,并选择“带锁平衡阀”进行布
置。
布置结果如下所示:
23
The information contained in this proposal is proprietary of BENTLEY and is not to be disclosed to any third party without BENTLEY’s prior written consent.
23
12/21/2020
6.3 快开排泥阀
参照规范《阀门产品样本 下 第 4 版》第 954 页,JM774X 型 PN6,PN10。
24
The information contained in this proposal is proprietary of BENTLEY and is not to be disclosed to any third party without BENTLEY’s prior written consent.
24
12/21/2020
阀门 EC Class 名字 QUICKLY_OPENING_SLUDGE_VALVE。
Spec 表 VLVCNTFL 的 COMP_LEN 列对应了规范中的 L 参数;表 VLVCNTFL 的
OPERATING_HEIGHT 列对应了规范中的 H 参数(H 应为阀体中心到顶部的高度,规范有
误)。Spec 表说明参见附录。
在 Open Plant Modeler 中,“阀门类”选择“控制阀”,并选择“快开排泥阀”进行布
置。
布置结果如下所示:
25
The information contained in this proposal is proprietary of BENTLEY and is not to be disclosed to any third party without BENTLEY’s prior written consent.
25
12/21/2020
6.4 明杆楔式闸阀
参照规范《阀门产品样本 上 第 4 版》第 37 页,Z41W 型 PN10。
26
The information contained in this proposal is proprietary of BENTLEY and is not to be disclosed to any third party without BENTLEY’s prior written consent.
26
12/21/2020
阀门 EC Class 名字 WEDGE_GATE_VALVE。
Spec 表 VLVCNTFL 的 COMP_LEN 列对应了规范中的 L 参数;表 VLVCNTFL 的
OPERATING_HEIGHT 列对应了规范中的 H 参数。Spec 表说明参见附录。
在 Open Plant Modeler 中,“阀门类”选择“控制阀”,并选择“明杆楔式闸阀”进行布
置。
布置结果如下所示:
27
The information contained in this proposal is proprietary of BENTLEY and is not to be disclosed to any third party without BENTLEY’s prior written consent.
27
12/21/2020
6.5 电磁阀
参照规范《阀门产品样本 下 第 4 版》第 990 页,ZSC-16 型。
阀门 EC Class 名字 ELECTRIC_GATE_VALVE。
Spec 表 VLVCNTSC 的 COMP_LEN 列对应了规范中的 L 参数。
28
The information contained in this proposal is proprietary of BENTLEY and is not to be disclosed to any third party without BENTLEY’s prior written consent.
28
12/21/2020
在 Open Plant Modeler 中,“阀门类”选择“控制阀”,并选择“明杆楔式闸阀”进行布
置。
布置结果如下所示:
29
The information contained in this proposal is proprietary of BENTLEY and is not to be disclosed to any third party without BENTLEY’s prior written consent.
29
12/21/2020
6.6 刀闸阀
参照规范《阀门产品样本 上 第 4 版》第 221 页,Z73H 型 PN10。
阀门 EC Class 名字 KNIFE_GATE_VALVE_WAFER。
Spec 表 VALVFL 的 COMP_LEN 列对应了规范中的 L 参数;表 VALVFL 的 OPERATING_HEIGHT
列对应了规范中的 H 参数。Spec 表说明参见附录。
在 Open Plant Modeler 中,“阀门类”选择“闸阀阀”,并选择“刀闸阀”进行布置。
30
The information contained in this proposal is proprietary of BENTLEY and is not to be disclosed to any third party without BENTLEY’s prior written consent.
30
12/21/2020
布置结果如下所示:
6.7 旋启式止回阀
参照规范《石油化工装置工艺管道安装设计手册 第 3 篇 阀门》第 226 页,H44W 型
PN10。
31
The information contained in this proposal is proprietary of BENTLEY and is not to be disclosed to any third party without BENTLEY’s prior written consent.
31
12/21/2020
阀门 EC Class 名字 SWING_CHECK_VALVE。
Spec 表 VALVFL 的 COMP_LEN 列对应了规范中的 L 参数;表 VALVFL 的 OPERATING_HEIGHT
列对应了规范中的 H 参数。Spec 表说明参见附录。
在 Open Plant Modeler 中,“阀门类”选择“止回阀”,并选择“旋启式止回阀”进行布
置。
32
The information contained in this proposal is proprietary of BENTLEY and is not to be disclosed to any third party without BENTLEY’s prior written consent.
32
12/21/2020
布置结果如下所示:
6.8 升降式止回阀
参照规范《阀门产品样本 下 第 4 版》第 248 页,H11W 型 PN16。
33
The information contained in this proposal is proprietary of BENTLEY and is not to be disclosed to any third party without BENTLEY’s prior written consent.
33
12/21/2020
阀门 EC Class 名字 LIFT_OPERATOR_CHECK_VALVE。
Spec 表 VALVSCSW 的 COMP_LEN 列对应了规范中的 L 参数;表 VALVSCSW 的
OPERATING_HEIGHT 列对应了规范中的 H 参数。Spec 表说明参见附录。
在 Open Plant Modeler 中,“阀门类”选择“止回阀”,并选择“升降式止回阀”进行布
置。
34
The information contained in this proposal is proprietary of BENTLEY and is not to be disclosed to any third party without BENTLEY’s prior written consent.
34
12/21/2020
布置结果如下所示:
6.9 球阀与手柄
参照规范《阀门产品样本 上 第 4 版》第 625 页,Q11F 型 PN10~64。
35
The information contained in this proposal is proprietary of BENTLEY and is not to be disclosed to any third party without BENTLEY’s prior written consent.
35
12/21/2020
阀门 EC Class 名字 BALL_VALVE_STRAIGHT;执行机构 EC Class 名字 WRENCH_BAR。
Spec 表 VALVSCSW 的 COMP_LEN 列对应了规范中的 L 参数;表 TOPWORKS 的
TOTAL_HEIGHT 列对应了规范中的 H 参数。Spec 表说明参见附录。
在 Open Plant Modeler 中,“阀门类”选择“球阀”,并选择“球阀与手柄”进行布置。
36
The information contained in this proposal is proprietary of BENTLEY and is not to be disclosed to any third party without BENTLEY’s prior written consent.
36
12/21/2020
布置结果如下所示:
6.10 活塞式减压阀
参照规范《阀门产品样本 下 第 4 版》第 735 页,Y43H 型 PN16。
37
The information contained in this proposal is proprietary of BENTLEY and is not to be disclosed to any third party without BENTLEY’s prior written consent.
37
12/21/2020
阀门 EC Class 名字 PISTON_PRESSURE_REDUCING_VALVE。
Spec 表 VLVRELFL 的 COMP_LEN 列对应了规范中的 L 参数,表 VLVRELFL 的 TOP_HEIGHT 列
对应了规范中的 H1 参数,BOTTOM_HEIGHT 列对应 H2 参数。Spec 表说明参见附录。
在 Open Plant Modeler 中,“阀门类”选择“泄放阀”进行布置。
38
The information contained in this proposal is proprietary of BENTLEY and is not to be disclosed to any third party without BENTLEY’s prior written consent.
38
12/21/2020
布置结果如下所示:
39
The information contained in this proposal is proprietary of BENTLEY and is not to be disclosed to any third party without BENTLEY’s prior written consent.
39
12/21/2020
7. 执行机构及其他
7.1 D941X 电动执行机构
参照规范《阀门产品样本 下 第 4 版》第 26 页,D941X 型。
EC Class 名字 ELECTRIC_CUBE_OPERATOR。
Spec 表 TOPWORKS 的 HANDLE_LENGTH 列对应了规范中的 B2 参数, TOTAL_HEIGHT 列对
应了规范中的 H 参数。Spec 表说明参见附录。
在 Open Plant Modeler 中,“执行机构类”选择“立方体”,并选择“Electric Cube
Operator”进行布置。
40
The information contained in this proposal is proprietary of BENTLEY and is not to be disclosed to any third party without BENTLEY’s prior written consent.
40
12/21/2020
布置结果如下所示:
7.2 D943H 电动执行机构
参照规范《阀门产品样本 下 第 4 版》第 142 页,D943H 型。
41
The information contained in this proposal is proprietary of BENTLEY and is not to be disclosed to any third party without BENTLEY’s prior written consent.
41
12/21/2020
EC Class 名字 MOTOR_VALVE_ACTUATOR。
Spec 表 TOPWORKS 的 TOTAL_HEIGHT 列对应了规范中的 H1 参数。Spec 表说明参见附录。
在 Open Plant Modeler 中,“执行机构类”选择“立方体”,并选择“Motor Valve
Actuator”进行布置。
布置结果如下所示:
42
The information contained in this proposal is proprietary of BENTLEY and is not to be disclosed to any third party without BENTLEY’s prior written consent.
42
12/21/2020
7.3 手柄
参照规范《阀门产品样本 上 第 4 版》第 625 页,Q11F 型 PN10~64。
43
The information contained in this proposal is proprietary of BENTLEY and is not to be disclosed to any third party without BENTLEY’s prior written consent.
43
12/21/2020
EC Class 名字 WRENCH_BAR。
Spec 表 TOPWORKS 的 TOTAL_HEIGHT 列对应了规范中的 H 参数。Spec 表说明参见附录。
可以和球阀一同使用,也可以单独使用。
在 Open Plant Modeler 中,“执行机构类”选择“阀门扳手”进行布置。
布置结果如下所示:
44
The information contained in this proposal is proprietary of BENTLEY and is not to be disclosed to any third party without BENTLEY’s prior written consent.
44
12/21/2020
7.4 电动刀闸阀
Z973X 型电动刀闸阀制造标准:
结构长度标准:GB/T 12221-2005
连接法兰标准:GB/T 9113
压力温度等级:GB/T 12224-2005
试验检验标准:GB/T 13927-2008
45
The information contained in this proposal is proprietary of BENTLEY and is not to be disclosed to any third party without BENTLEY’s prior written consent.
45
12/21/2020
46
The information contained in this proposal is proprietary of BENTLEY and is not to be disclosed to any third party without BENTLEY’s prior written consent.
46
12/21/2020
EC Class 名字 MOTOR_OPERATED_VALVE_ACTUATOR_WITH_HAND_WHEEL。
Spec 表 TOPWORKS 的 TOTAL_HEIGHT 列对应了规范中的 H 参数。Spec 表说明参见附录。
在 Open Plant Modeler 中,“执行机构类”选择“电动机”进行布置。
布置结果如下所示:
47
The information contained in this proposal is proprietary of BENTLEY and is not to be disclosed to any third party without BENTLEY’s prior written consent.
47
12/21/2020
48
The information contained in this proposal is proprietary of BENTLEY and is not to be disclosed to any third party without BENTLEY’s prior written consent.
48
12/21/2020
7.5 法兰限位伸缩接头
VSSJA 型技术参数:
49
The information contained in this proposal is proprietary of BENTLEY and is not to be disclosed to any third party without BENTLEY’s prior written consent.
49
12/21/2020
EC Class 名字 PIPE_COUPLING_STRETCH。
Spec 表 MISC_FIT 的 COMP_LEN 列对应了规范中的 L 参数,FIX_PART_LENGTH 对应 L1 参
数。Spec 表说明参见附录。
在 Open Plant Modeler 中,“接头类”选择“接头”,并选择“Pipe Coupling Stretch”进
行布置。
50
The information contained in this proposal is proprietary of BENTLEY and is not to be disclosed to any third party without BENTLEY’s prior written consent.
50
12/21/2020
布置结果如下所示:
51
The information contained in this proposal is proprietary of BENTLEY and is not to be disclosed to any third party without BENTLEY’s prior written consent.
51
12/21/2020
7.6 不锈钢波纹管
简介:
金属软管(简称软管)是现代工业管路中一种高品质的柔性管道。它主要由波纹管、网套
和接头组成。它的内管是具有螺旋形或环形波形的薄壁不锈钢波纹管,波纹管外层的网
套,是由不锈钢丝或钢带按一定的参数编织而成。软管两端的接头(法兰)是与客户管道
的接头(法兰)相配的。
EC Class 名字 FLEXIBLE_METAL_TUBING。
Spec 表 PIPE 的 MAIN_SIZE 列为管径大小。Spec 表说明参见附录。
在 Open Plant Modeler 中,“管道类”选择“管段”进行布置。
52
The information contained in this proposal is proprietary of BENTLEY and is not to be disclosed to any third party without BENTLEY’s prior written consent.
52
12/21/2020
左键画管,用户确定长度,右键结束后布置结果如下所示:
53
The information contained in this proposal is proprietary of BENTLEY and is not to be disclosed to any third party without BENTLEY’s prior written consent.
53
12/21/2020
Appendix 1: Spec数据库中相关表与字段说明
新建阀门等管件的等级数据主要涉及 Spec 数据库中的阀门表如 VLVCNTFL,VALVFL 和
VALVSCSW,执行机构表 TOPWORKS,其他还有 MISC_FIT 和 PIPE 表。下面就其中部分公共
的列做详细说明。
列名 描述
MEAS_UNITS ME 公制 IM 英制
CATALOG 标准手册/规范的名字
TAG 主型号名字
LONG_DESCR 长描述
WEIGHT_DRY 干重
PIPE_OD_M 入口外径
CTR_END_M 中心距 mainport 长度
CTR_END_R 中心距 runport 长度
COMP_LEN 长度
OPERATOR_HEIGHT 阀门高度
HANDWL_OD 手轮外径
HANDWL_LEN 手轮长度
OPERATOR 执行机构的 EC CLASS 名字
RUN_SIZE 出口长度,不填则与 MAIN_SIZE 一样
REV 版本号
END_COND_1 入口连接方式:例如 FF/SCF/RF
END_COND_2 出口连接方式,不填则同 END_COND_1
END_COND_3 分支连接方式,不填则同 END_COND_1
MAIN_SIZE 公称直径,公制用 mm 单位
FACING_1/2/3 法兰连接时指定端面类型:FF/RF 等,螺纹连接的不填
SCHEDULE 壁厚等级
RATING 压力等级如 PN10
MATERIAL 材料
MANU_FACT 供应商
OPTIONCODE 如使用 Use Spec Defaults,则值 1 将此数据设为默认,比非 1 的优先
SYS_ID 内部使用,不需填写
54
The information contained in this proposal is proprietary of BENTLEY and is not to be disclosed to any third party without BENTLEY’s prior written consent.
54
12/21/2020
Appendix 2: China First使用工具说明
新增 China First 属性导入工具,可通过此工具,批量添加/修改 OpenPlant 中设备/管线
属性。详细操作方法,请见帮助文档。
以下为部分截图
使用“导入属性”工具,用户可以从 Excel 文件导入属性数据,批量修改管线/设备等对象
属性,方便批量修改。使用方法如下:
启动 OpenPlant Modeler,打开需要导入的.dgn 文件,选择“China First”的 ”导入属性” 。
结果如下:
55
The information contained in this proposal is proprietary of BENTLEY and is not to be disclosed to any third party without BENTLEY’s prior written consent.
55
12/21/2020
56
The information contained in this proposal is proprietary of BENTLEY and is not to be disclosed to any third party without BENTLEY’s prior written consent.
56
12/21/2020
WWT Workspace CCK 使用说明