1

PROGRAMMING MANUAL FOR UNDERPLASTER RADIO CONTROLLER AL-RSP 01

Production plant in Opole

ul. Gosławicka 3, 45-446 Opole, Poland

tel: +48 77 40 00 000, fax. +48 (77) 40 00,006

e-mail: Aluprof@aluprof.eu

Headquarters; Production plant in Bielsko-Biała

ul. Warszawska 153, 43-300 Bielsko-Biała, Poland

tel: +48 33 81 95 300, fax. +48 33 82 28 512

- power supply: 230 VAC / 50 Hz, - transmission frequency: 433.92 MHz, - transmission power: 10 milliwatt (mW), - operating temperature: ~ 0OC to +45OC, - controlling of the motor or two light circuits, - installation in standard flush box, - transmission distance: 200 metres (open area) 35 metres (built-up area) . Works only with motors without built-in radio control.

Works with all transmitters from DC series offered by ALUPROF S.A.

(excluding transmitter DC 115B).

The manufacturer reserves the tolerance of catalogue data due

to use in different conditions.

Technical specification

Wiring diagram

In accordance with the provisions of the Directive of the European Parliament and the Council 2012/19/UE of 4 July 2012 on waste electrical

and electronic equipment (WEEE), it is prohibited to place together with other wastes used equipment marked with the symbol of crossed

out bin. The user is obliged to transfer used equipment to a designated collection point for proper processing. The marking means that at

the same time the equipment was launched on the market after 12 August 2005. Above legal obligations have been introduced to reduce

the amount of waste generated from waste electrical and electronic equipment and to ensure an appropriate level of collection, recovery

and recycling. No harmful components, which have a particularly negative impact on the environment and human health are included in

the equipment components.

NOTE

- Installation of the radio control should be carried out by authorized persons.

- The radio control is designed for use in dry rooms and should not be exposed to direct weather conditions.

- The radio control should be powered by a separate circuit and protected by a quick fuse for example: circuit breaker type B10.

Motor wiring diagram Lighting circuit wiring diagram

2

Change of work mode

OK

The LED flashes twice in the current mode colour and then twice in the colour of the new

mode

While the power supply is ON press 5x the programming button PROG,

which will be confirmed by LED lightning

RED COLOUR Mode of roller shutter operation

GREEN COLOUR Mode of lightning control

operation

I - Mode of roller shutter operation

1. Programming of the first transmitter

By turning on power supply

The transmitter has been programmed

Turn on the power, which will be confirmed by the UP-DOWN

movement

OK

In the interval of two seconds press the “P2” button twice,

which will be confirmed by the UP-DOWN movement

Press the “UP” button, which will be confirmed by the UP-DOWN

movement

Using the programming button

The transmitter has been programmed

While the power supply is ON press 3x the programming button PROG,

which will be confirmed by LED lightning

OK

In the interval of two seconds press the “P2” button twice,

which will be confirmed by the UP-DOWN movement

Press the “UP” button, which will be confirmed by the UP-DOWN

movement

Using the two-way switch

The transmitter has been programmed

While the power supply is ON

quickly 3x press the button “UP” or “DOWN” on the switch, which will

be confirmed by the UP-DOWN movement

OK

In the interval of two seconds press the “P2” button twice,

which will be confirmed by the UP-DOWN movement

Press the “UP” button, which will be confirmed by the UP-DOWN

movement

3

Press twice the button “P2” of the already programmed transmitter, which will be confirmed by the UP-DOWN movement

Press the button “P2” of the new transmitter, which will be confirmed by the UP-DOWN

movement

The new transmitter has been

programmed.

2. Adding an additional transmitter

OK

3. Deleting transmitter

OK

Press the “P2” button, which will be confirmed by the UP-DOWN

movement

Press the “STOP” button, which will be confirmed by the UP-

DOWN movement

Press the “P2” button, which will be confirmed by the UP-DOWN

movement

The transmitter has been deleted

II - mode of lightning control operation

4. Programming of the first transmitter

By turning on power supply

The transmitter has been programmed

Turn on the power, which will be confirmed by applying voltage to

the output W1 and W2

OK

In the interval of two seconds press the button “P2”

(1xP2 for W1, 2xP2 for W2), which will be confirmed by

applying brief voltage pulses to the output W1 or W2

Press the button “UP”, which will be confirmed by applying voltage

to the output W1 or W2

Using the programming button

The transmitter has been programmed

While the power supply is ON press 3x the programming button PROG,

which will be confirmed by LED lightning

OK

In the interval of two seconds press the button “P2”

(1xP2 for W1, 2xP2 for W2), which will be confirmed by

applying brief voltage pulses to the output W1 or W2

Press the button “UP”, which will be confirmed by applying brief

voltage pulses to the output W1 or W2

4

Using the two-way switch

The transmitter has been programmed

While the power supply is ON

quickly 3x press the button “UP” or “DOWN” on the switch, which will

be confirmed applying voltage to the output W1 and W2

OK

In the interval of two seconds press the button “P2”

(1xP2 for W1, 2xP2 for W2), which will be confirmed by

applying brief voltage pulses to the output W1 or W2

Press the button “UP”, which will be confirmed by applying brief

voltage pulses to the output W1 or W2

Press the button “P2” of the already programmed transmitter, which will be

confirmed by applying brief voltage pulses to the output W1 or W2

Press the button “P2” of the new transmitter, which will be confirmed by applying brief voltage

pulses to the output W1 or W2

The new transmitter has been

programmed.

5. Adding an additional transmitter

OK

While the power supply is ON press 7x the programming button PROG,

which will be confirmed by LED lightning

The led will turn colour green - red - green

All transmitters have been deleted

The LED will turn red, which will be confirmed by applying brief voltage pulses to the output

W1 or W2 (the motor performs movement up - down)

OK

6. Deleting selected transmitter

OK

Press the button “P2”, which will be confirmed by applying brief

voltage pulses to the output W1 or W2

Press the button “STOP”, which will be confirmed by applying

brief voltage pulses to the output W1 or W2

Press the button “P2”, which will be confirmed by applying brief

voltage pulses to the output W1 or W2

The transmitter has been deleted

7. Return to the factory settings

The procedure of returning to factory settings is identical for both working modes and removes all transmitters programmed in the control unit