Sop Harvester Final Edition

Page:1

审核：Tyle Zhang ,Jin You HuJ Y Hou ,Song Qiang Z

Harvester SOP(Suede/Nappa)

客户：Manitobah 鞋型号：Tall Suede Mukluk 削边 Skiving Page:2L5 L6 L7 L8 L9 L10 L11

1 左/右鞋面Left/Right Foot — — — — — — — 后跟削5MM出尾1.2MM

2 左/右鞋盖 L/R Vamp — — — — — — —3 鞋舌 Collar — — — — — — —4 鞋带 Lace — — — — — — —5 左/右鞋垫 L/R Insole — — — — — — —6 鞋盖内衬 vamp linging — — — — — — —7 上口流苏 Collar fringe — — — — — 上边削5MM出尾1.2MM8 鞋身 Qarter — — — — — — —9 后跟条 Back central strip — — — — — — — 上边削5MM出尾1.2MM

核准：审核：

Cutting and Skiving裁断

部位Parts

—

1 2 3 4

制表：刘利君

12

5 6 7 8

9 10 11

3

Page:3

surface of rubber.Follow the pattern as requested No air buble or gap.

4.大底打粗 Outsole roughing

必须要直并且紧位置正确，不能有包风脱落情形。

Must be tight and straight Must be right at positing.

打粗要均匀，橡胶表面要完全破坏

Preparing process

2.贴鞋面补强 Backing lining on vamp.

Rouging evenly and skining off

1.鞋面发外绣珠 Vamp Beading.

Preparing process

Needle Thread # Sewing edge SOP Page:4

针型号边距备注

1 箭尾针 1.5-2MM 平车

2 箭尾针 3MM 万能车

3 箭尾针 3MM 高头车

4 手缝针高头车

5 箭尾针万能车

6 箭尾针高头车





11 箭尾针 2MM 平车

12 箭尾针 2MM 平车

缩腰 Sewing waist split. 210D/3 9-8 stitches /1 "

后跟下缘合缝 Overlapping counter and heel. 210D/3 9-8 stitches /1 "

后跟拼缝 Zigzagging heel. 210D/3 9-8 stitches /1 "

9-8 stitches /1 "

9-8 stitches /1 "

210D/3 9-8 stitches /1 "

Sewing process 流程 Processes 线型针距

缝鞋面马克线 Toe Lacing 300D/16 6-5 stitches /1 "

内外腰鞋身缝合 Quarter and collar sewing overlapping. 210D/3 6-5 stitches /1 "

车产地标 Sewing size /brand label on insole.

210D/3

车后跟条 Overlapping heel center strip. 210D/3

210D/3

鞋舌与鞋身车合（起收针倒针至少4针）Tongue attachement. 210D/3 9-8 stitches /1 "

在鞋垫上车商标 Content/country original label attaching.

9-8 stitches /1 "

鞋身与上口流苏车合 Collar fringe sewing. 210D/3 9-8 stitches /1 "

12

车上口流苏 Folding and locking sewing on fringe.

9 10 11

鞋身与底部车双线 Vamp and vamp bottom sewing. 210D/3 9-8 stitches /1 "

1. 2. 3 4

5 6. 7. 8

1. 2. 3 4

5 6. 7. 8

1

2

3

4

5 鞋头后跟高度内外腰定位 Control height of in/out ball ,toe and heel.and check height of in/outtoe and heel.

6 过锤 Tapering upper evenly against last.

7

8 品检 Inspetion

9 加硫定型 Forming in moistering, heatingm , and vaccuming oven.

10

11

核准：审核：制表：刘利君

Lasting 攀鞋备注 Treatment: Page:4

整理，配料 matching pair and sorting last.

蒸湿 Miostering upper. 5秒，110度 5 second. Temperature .110 degree Celsis

套楦 Placing proper last into upper.

入楦 Lasting.

夹马克线 Trimming lacing shape.

18分钟，130度 18 minutes, 130C

画线 Marking lasted upper for roughing, premiering, and cementing.

打粗（绒面革不用打粗）Roughing ( suede doesn't apply to roughing).1 3 4

5 6 7 8

9 10 12

2.

11

2.

Page:6

1

2

3

4

5

6

7


刷鞋面处理剂 Primering bottom of lasted upper.

Cementing 擦胶

备注

刷鞋底处理剂 Primering rubber out sole.

过烤箱 Drying in heat tunnel. 实际温度60度，3分钟 60 C ,3 minutes

刷一次胶 First coat cmenting.

过烤箱 Activating and drying cement. 实际温度60度，3分钟 60 C ,3 minutes

5 6 7 8

刷二次胶 Second coat of cement.

过烤箱 Final activation of cement. 实际温度80度，3分钟 80 C, 3 minutes.

1 2 3 4

Page:7

1贴底 Sole laying.

2

3手压后跟 Hammering on heel.

4

5


Sole laying 贴底

备注

压底 Pressing. 8秒钟，25公斤压力 8 second, 25KGS/per inch

冷却 Cooling(post curing). 1分钟，—5度 I minute, below zero 5 C

脱楦 De-lasting

5

1 2 3 4

Page:81

2

3

4

5

6

7

8

9 挂吊牌 Tagging.

10

11

12

13

14


Packing 包装整理

清洁 Cleaning and pairing.

鞋垫配双 Matching up insole.

整理 Inspection

总品检 Final inspection.

小包装（分码放包装纸，干燥剂，备用鞋带，小册子）Value add tagging.

鞋垫和鞋内刷胶 Gluing on insole.

放鞋头和鞋身纸撑+码数章 Insert and size marker.

配盒贴条码标 Labeling.

过烤箱 Drying and activting. 60-70度，2分钟

放鞋垫 Placing insole.

第一次品检 inspection.

11 12

贴红色标签 innerbox label.

大包装 Packing

1 2 3 4

13 14

5 6 7 8

. .

10

. .

9

Documents

Sop Harvester Final Edition