TPI Fans, Heaters, and Lights - The Lawless Grouplawlessgroup.com/catalog/TPI.pdf · Toll-Free: 1-800-462-4983 3 View & Search Complete Catalog at LawlessGroup.com TPI CORPORATION

Toll-Free: 1-800-462-4983

1 View & Search Complete Catalogat LawlessGroup.com

TPI CORPORATIONMini-BlowersFloor StyleTotally enclosed motor allows mini-blower to be used in dirty or dusty environments. • 2-speed, 1/4 HP, 1

Phase, 120 volt, ball bearing, perma-nently lubricated, permanent split capacitor motor

• Rotary switch• SJT type, 3 conduc-

tor, 10’ long cord• Aluminum blade• Spiral wire - front and rear guards• Corrosion and dent proof high density poly-

ethylene housing• Meets OSHA standards• 1 Year Limited Warranty• UL listed

TPI CORPORATIONMini-BlowersYoke StyleTotally enclosed motor allows mini-blower to be used in dirty or dusty environments. • 2-speed, 1/4 HP, 1

Phase, 120 volt, ball bearing, perma-nently lubricated, permanent split capacitor motor

• Pull chain switch• SJT type, 3 conductor, 10’ long cord• Aluminum blade• Spiral wire - front and rear guards• Corrosion and dent proof high density poly-

ethylene housing• Meets OSHA standards• 1 Year Limited Warranty• UL listed

TPI CORPORATIONDirect Drive Portable BlowersSwivel

• Corrosion and dent proof high density polyethylene housing

• 36” & 42” rotates 360° in 12-1/2” incre-ments and locks in place with steel lock-ing pin

• 8” wheels• Single phase, 120V,

ball bearing, permanently lubricated, 1040 rpm, permanent split capacitor motor

• Rocker switch• SJT type 3 conductor, 12’ long cord• 3 paddle aluminum blade• Spiral wire front and rear guards• Meets OSHA standards• UL listed• 1 year limited warranty

TPI CORPORATIONDirect Drive Portable Blowers

• Corrosion and dent proof high density polyethylene housing

• 8” wheels• Single phase, 120V,

ball bearing, perma-nently lubricated, 1040 rpm, permanent split capacitor motor

• Rocker switch• SJT type 3 conductor, 12’ long cord• 3 paddle aluminum blade• Spiral wire front and rear guards• Meets OSHA standards• UL listed• 1 year limited warranty

TPI CORPORATIONDirect Drive Portable Blowers48” Standard & Swivel

• Corrosion and dent proof high density polyethylene hous-ing

• Swivel model rotates 360° in 12-1/2” increments and locks in place with steel locking pin

• 10” wheels• 3/4HP, 1 speed, single phase, 17,300 CFM,

10.3 amps, 120V, ball bearing, permanently lubricated, 824 rpm, permanent split capacitor motor

• Rocker switch• SJT type 3 conductor, 12’ long cord• 2 paddle steel blade• Spiral wire front and rear guards• Meets OSHA standards• UL listed• 1 year limited warranty

TPI CORPORATIONDirect Drive Suspension Blowers

• 2 speed, 1 phase, 120V, 1050 RPM, ball bearing, per-manently lubri-cated, permanent split capacitor motor

• Rocker switch• SJT type 3 con-

ductor, 12’ long cord

• Aluminum blades• Spiral wire front and rear guards• Corrosion and dent proof high density poly-

ethylene housing• Meets OSHA standards• UL listed• 1 year limited warranty

**Non Stock**

Mfg Part# Size CFM Amps

ShipWt

(lbs) PkMB 24-DF 24” 6800/5000 2.2 52 1MB 30-DF 30” 7800/6000 2.5 58 1

Mfg Part# Size CFM Amps

ShipWt

(lbs) PkMB 24-DY 24” 6800/5000 2.2 52 1MB 30-DY 30” 7800/6000 2.5 58 1

Optional wall/ceiling mountMBM-W -- -- -- 4 1

Mfg Part# Size Spd HP CFM Amps

ShipWt

(lbs) PkPBS 36-D 36” 2 1/3 12500/

90005.5 110 1

PBS 42-D 42” 1 1/2 15600 6.0 128 1

Mfg Part# Size Spd HP CFM Amps

ShipWt

(lbs) PkPB 36-D 36” 2 1/3 12500/9000 5.5 82 1PB 42-D 42” 1 1/2 15600 6.0 102 1

Mfg Part# Size

FanType

ShipWt

(lbs) PkPB 48-D-OP 48” Standard 117 1

PBS 48-D-OP 48” Swivel 142 1

Mfg Part# Size HP CFM Amps

ShipWt

(lbs) PkSB 30-D 30” 1/4 7800/6000 2.5 58 1SB 36-D 36” 1/3 12500/9000 5.6 70 1SB 42-D 42” 1/2 16200 7.9 99 1

< Back to LawlessGroup.com

http://LawlessGroup.com

Local: 972-247-8871

View & Search Complete Catalog 2at LawlessGroup.com

TPI CORPORATIONBelt Drive Suspension Blowers


• External junction boxes on dual volt-age models allow units to be wired for either voltage with-out removing guards

• Hazardous Location Models have explosion proof motors and external junction boxes rated for Class I, Group D and Class II, Groups E, F & G

• 2-speed permanently lubricated ball bear-ing motor on 30” & 36” models (1-speed motor on 42” model)

• Rocker switch on 120V, 1 Phase models• SJT type 3 conductor, 12’ long cord on

120V, 1 Phase models; no cords on dual voltage models

• Aluminum blades• Powder coated spiral wire front and rear

guards• Meets OSHA Standards• UL Listed• 1 Year Limited Warranty

**Non Stock**

TPI CORPORATIONBelt Drive Portable Blowers


• 10” wheels• External junction

boxes on dual volt-age models allow units to be wired for either voltage without removing guards

• Hazardous Location Models have explo-sion proof motors and external junction boxes rated for Class I, Group D and Class II, Groups E, F & G

• 1-speed, permanently lubricated ball bear-ing motor

• Rocker switch on 120V, 1 Phase models• SJT type 3 conductor, 12’ cords long on


• Aluminum, 4 paddle blade• Spiral, wire front and rear guards• Meets OSHA Standards• UL Listed• 1 Year Limited Warranty

TPI CORPORATIONBelt Drive Portable BlowersSwivel


• Rotates 360° in 12.5° increments and locks in place with a steel locking pin

• 10” wheels• External junction boxes on dual voltage

models allow units to be wired for either voltage without removing guards

• Hazardous Location Models have explo-sion proof motors and external junction boxes rated for Class I, Group D and Class II, Groups E, F & G

• 1-speed, permanently lubricated ball bear-ing motor

• Rocker switch on 120V, 1 Phase models• SJT type 3 conductor, 12’ cords long on


• Aluminum, 4 paddle blade• Spiral, wire front and rear guards• Meets OSHA Standards• UL Listed• 1 Year Limited Warranty

MfgPart#

MotorType Amps

ShipWt

(lbs) Pk

36” 1/2 HP, 14,500 CFM, 500RPMSB 36-B 120V 8.0 120 1

SB 36-B-3 240/480V 2.3/1.1 127 1SB 36-B-HL 120/240V 7.8/3.9 135 1

42” 3/4 HP, 18,200 CFM, 430RPMSB 42-B 1 PH 11.0 135 1

SB 42-B-3 3 PH 3.3/1.5 143 1SB 42-B-HL 1 PH 10.8/5.4 150 1

48” 1 HP, 22,700 CFM, 390RPMSB 48-B ODP 15.0 155 1

SB 48-B-3 ODP 3.8/1.9 164 1SB 48-B-HL EXP 13.2/6.6 173 1

Mfg Part#

MotorType Amps RPM

ShipWt

(lbs) Pk

36” 1/2 HP, 14,500 CFM, 500 RPMPB 36-B 120V 8.0 500 120 1

PB 36-B-3 230/460V 2.3/1.1 500 127 1PB 36-B-HL 115/230V 7.8/3.9 500 135 1

42” 3/4 HP, 18,200 CFM, 430 RPMPB 42-B 1 PH 11.0 430 135 1

PB 42-B-3 3 PH 3.3/1.5 430 143 1PB 42-B-HL 1 PH 10.8/5.4 430 150 1

48” 1 HP, 22,700 CFM, 390 RPMPB 48-B ODP 15.0 390 155 1

PB 48-B-3 ODP 3.4/1.7 390 164 1PB 48-B-HL EXP 13.2/6.6 390 173 1

MfgPart#

MotorType Amps

ShipWt

(lbs) Pk

36” 1/2 HP, 14,500 CFM, 500RPMPBS 36-B 120V 8.0 145 1

PBS 36-B-3 240/480V 2.3/1.1 152 1PBS 36-B-HL 120/240V 7.8/3.9 160 1

42” 3/4 HP, 18,200 CFM, 430RPMPBS 42-B 1 PH 11.0 160 1

PBS 42-B-3 3 PH 3.3/1.5 168 1PBS 42-B-HL 1 PH 10.8/5.4 175 1

48” 1 HP, 22,700 CFM, 390RPMPBS 48-B ODP 15.0 180 1

PBS 48-B-3 ODP 3.4/1.7 189 1PBS 48-B-HL EXP 13.2/6.6 198 1



Toll-Free: 1-800-462-4983


TPI CORPORATIONAssembled CirculatorsFan Heads

• Factory assembled and tested fan heads and mounts can be used with any of the six mounts

• 2 speed, 120V, 1 phase, ball bearing, totally enclosed, permanently lubri-cated permanent split capacitor motor

• Pull chain switch• Oscillating model oscillates in a 90° arc or

can be locked in a fixed position• Metal gears in the oscillating mechanism

allow the fan to operate at a maximum 30° downward tilt

• 12’ SJT type 3 conductor cord• Coated steel guards• Steel hub/spider aluminum paddle blades• 1/2” shaft• Meets OSHA standards• Intertek listed

TPI CORPORATIONCirculatorsPedestal Mount

• Factory assembled and tested

• Available as unas-sembled (see blue text below)

• Pedestal pole adjusts the center of fan from 52” to 78” and bolts to 27” diameter steel dome base with 5 carriage bolts

• 2 speed, 120V, 1 phase, ball bearing, totally enclosed, permanently lubri-cated permanent split capacitor motor

• Pull chain switch• Oscillating model

oscillates in a 90° arc or can be locked in a fixed position

• Metal gears in the oscillating mecha-nism allow the fan to operate at a max-imum 30° down-ward tilt


Part numbers in blue text indicate Unassem-bled circulators and mounts. Motor, blades, guard, and mount are packed and shipped in a single UPS-able carton.

TPI CORPORATIONCirculatorsWall Mount


• Available as unas-sembled (see blue text below)

• Wall Mount• 2 speed, 120V, 1

phase, ball bearing, totally enclosed, per-manently lubricated permanent split capacitor motor






Mfg Part# Size CFM Amps Warranty

Wt(lbs) Pk

1/2 HP Heavy-DutyHDH-24G 24” 8600/7100 3.5 5 yrs 44 1HDH-30G 30” 9850/8100 4.0 5 yrs 48 1

1/3 HP High PerformanceIHP 24-H 24” 7000/5200 2.8 3 yrs 40 1IHP 30-H 30” 8200/6200 3.0 3 yrs 44 1

1/4 HP Standard IndustrialACH 24 24” 6800/5000 2.5 1 yr 40 1ACH 30 30” 7900/6000 2.7 1 yr 44 1

1/4 HP Oscillating IndustrialAC 24-O 24” 6800/5000 2.5 1 yr 44 1AC 30-O 30” 7900/6000 2.7 1 yr 48 1

Mfg Part# Size Includes CFM Amps

Wt(lbs)

1/3 HP Industrial High Performance -(fan head & mount)

IHP-24-PUHP-24-P

24” IHP 24-H& ACM-P

7000/5200

2.8 75

IHP-30-PUHP-30-P

30” IHP 30-H& ACM-P

8200/6200

3.0 78

1/4 HP Standard Industrial - (fan head & mount)AC 24-P

ACU-24-P24” ACH 24

& ACM-P6800/5000

2.5 75

AC 30-PACU-30-P

30” ACH 30& ACM-P

7900/6000

2.7 78

1/4 HP Oscillating Industrial - (fan head & mount)AC 24-PO

ACU-24-PO24” ACH 24-O

& ACM-PO6800/5000

2.5 79

AC 30-POACU-30-PO

30” ACH 30-O& ACM-PO

7900/6000

2.7 82

Pedestal Mount OnlyACM-P 30” Pedestal

Mount-- -- 34

ACM-WK -- Optional Wheel Kit

-- -- 4

MfgPart# Sz Includes CFM Amps

Wt(lbs)

1/3 HP Industrial High Performance -(fan head & mount)

IHP 24-WUHP 24-W

24” IHP 24-W& ACM-W

7000/5200

2.8 45

IHP 30-WUHP 30-W

30” IHP 30-H& ACM-W

8200/6200

3.0 48

1/4 HP Standard Industrial - (fan head & mount)AC 24-W

ACU 24-W24” ACH 24

& ACM-W6800/5000

2.5 45

AC 30-WACU 30-W

30” ACH 30& ACM-W

7900/6000

2.7 48

1/4 HP Oscillating Industrial - (fan head & mount)AC 24-WO

ACU 24-WO24” ACH 24-O

& ACM-W6800/5000

2.5 49

AC 30-WOACU 30-WO

30” ACH 30-O& ACM-W

7900/6000

2.7 52

Wall Mount OnlyACM-W -- Wall Mount -- -- 3



Local: 972-247-8871


TPI CORPORATIONCirculatorsI-Beam Mount

• Factory assembled and tested• Available as unassembled (see blue text

below)• I-Beam Mount requires 1-1/2” or longer

pipe nipple for assembly (not supplied)• 2 speed, 120V, 1 phase, ball bearing,

totally enclosed, permanently lubricated permanent split capacitor motor

• Pull chain switch• 12’ SJT type 3 conductor cord• Coated steel guards• Steel hub/spider aluminum paddle blades• 1/2” shaft• Meets OSHA standards• Intertek listed


TPI CORPORATIONCirculatorsCeiling Mount


• Available as unassem-bled (see blue text below)

• Ceiling Mount requires 1-1/2” or longer pipe nipple for assembly (not supplied)

• 2 speed, 120V, 1 phase, ball bearing, totally enclosed, per-manently lubricated permanent split capaci-tor motor

• Pull chain switch• 12’ SJT type 3 conductor cord• Coated steel guards• Steel hub/spider aluminum paddle blades• 1/2” shaft• Meets OSHA standards• Intertek listed


TPI CORPORATIONCirculatorsSuspension Mount


• Available as unassembled (see blue text below)

• Suspension Mount• 2 speed, 120V, 1 phase,

ball bearing, totally enclosed, permanently lubricated permanent split capacitor motor

• Pull chain switch• 12’ SJT type 3 conductor

cord• Coated steel guards• Steel hub/spider aluminum paddle blades• 1/2” shaft• Meets OSHA standards• Intertek listed



Wt(lbs) Pk

1/3 HP Industrial High Performance -(fan head & mount)IHP 24-IUHP 24-I

24” IHP 24-H& ACM-I

7000/5200

2.8 50 1

IHP 30-IUHP 30-I

30” IHP 30-H& ACM-I

8200/6200

3.0 53 1

1/4 HP Standard Industrial - (fan head & mount)AC 24-I

ACU 24-I24” ACH 24-H

& ACM-I6800/5000

2.5 50 1

AC 30-IACU 30-I

30” ACH 30-H& ACM-I

7900/6000

2.7 53 1

I-Beam Mount OnlyACM-I -- Mount -- -- 9 1


Wt(lbs) Pk

1/3 HP Industrial High Performance -(fan head & mount)IHP 24-CUHP 24-C

24” IHP 24-H& ACM-C

7000/5200

2.8 45 1

IHP 30-CUHP 30-C

30” IHP 30-H& ACM-C

8200/6200

3.0 48 1

1/4 HP Standard Industrial - (fan head & mount)AC 24-C

ACU 24-C24” ACH 24-H

& ACM-C6800/5000

2.5 45 1

AC 30-CACU 30-C

30” ACH 30-H& ACM-C

7900/6000

2.7 48 1

Ceiling Mount OnlyACM-C -- Mount -- -- 3 1


Wt(lbs) Pk

1/3 HP Industrial High Performance(fan head & mount)IHP 24-SUHP 24-S

24” IHP 24-H& ACM-S

7000/5200

2.8 43 1

IHP 30-SUHP 30-S

30” IHP 30-H& ACM-S

8200/6200

3.0 46 1

1/4 HP Standard Industrial - (fan head & mount)AC 24-S

ACU 24-S24” ACH 24-H

& ACM-S6800/5000

2.5 43 1

AC 30-SACU 30-S

30” ACH 30-H& ACM-S

7900/6000

2.7 46 1

Suspension Mount OnlyACM-S -- Mount -- -- 2 1

Search our online catalog at:LawlessGroup.com



Toll-Free: 1-800-462-4983


TPI CORPORATIONAssembled CirculatorsPole Mount

• Factory assem-bled and tested

• Pole Mount attaches to 4”, 6”, or 8” with U-bolts (not sup-plied)

• 2 speed, 120V, 1 phase, ball bearing, totally enclosed, per-manently lubricated permanent split capac-itor motor





TPI CORPORATIONAssembled Heavy Duty CirculatorsVarious Mount Options

• Factory assembled and tested fan heads and mounts

• Safety yellow pow-der coated guards and mounts

• 1/2 HP, 2 speed, 1 phase, 120V ball bearing, totally enclosed perma-nently lubricated permanent split capacitor motor

• Pull chain switch• 12’ SJT type 3 con-

ductor cord• Steel hub/spider alu-

minum paddle blades

• Pedestal mount option: pole adjusts the center of the fan from 52 to 78 inches; attaches to 27” in dome base with 5 carriage bolts

• Meets OSHA standards• Intertek listed• 5 year limited warranty

Other Mount Options [Left to Right]:I-Beam (HDM-I), Wall (HDM-W), Ceiling (HDM-C)

TPI CORPORATIONUnassembled Maximum DutyCirculatorsVarious Mount Options

• Easy access, coated steel, hinged guard

• 2 speed, 1 phase, 120V ball bear-ing, totally enclosed perma-nently lubricated permanent split capacitor motor

• 1/2” shaft• Drop down 2

speed switch• 6’, 9’, or 12’ exten-

sion cord options (not included)

• Steel hub/spider aluminum paddle blades

• Meets OSHA standards

• Intertek listed

* For 30” model, replace “24” with “30” in the part number and add 3 lbs to shipping weight.


Wt(lbs)

1/3 HP Industrial High Performance -(fan head & mount)IHP 24-PM 24” IHP 24-H

& ACM-PM7000/5200

2.8 46

IHP 30-PM 30” IHP 30-H & ACM-PM

8200/6200

3.0 49

1/4 HP Standard Industrial - (fan head & mount)AC 24-PM 24” ACH 24

& ACM-PM6800/5000

2.5 46

AC 30-PM 30” ACH 30 & ACM-PM

7900/6000

2.7 49

1/4 HP Oscillating Industrial - (fan head & mount)AC 24-PMO

24” ACH 24-O & ACM-PM

6800/5000

2.5 52

AC 30-PMO

30” ACH 30-O & ACM-PM

7900/6000

2.7 55

Pole Mount OnlyACM-PM -- Pole Mount -- -- 5


ShipWt

(lbs)

Pedestal MountHD 24-P 24” HDH 24-JR

& HDM-P8600/6500

3.5 78

HD 30-P 30” HDH 30-JR& HDM-P

9850/7500

4.0 82

Wall MountHD 24-W 24” HDH 24-JR

& HDM-W8600/6500

3.5 47

HD 30-W 30” HDH 30-JR & HDM-W

9850/7500

4 51

I-Beam MountHD 24-I 24” HDH 24-JR

& HDM-I8600/6500

3.5 53

HD 30-I 30” HDH 30-JR & HDM-I

9850/7500

4 57

Ceiling MountHD 24-C 24” HDH 24-JR

& HDM-C8600/6500

3.5 47

HD 30-C 30” HDH 30-JR & HDM-C

9850/7500

4 51

Optional Wheel KitACM-WK -- -- -- -- 4

Size Type CFM Amps

24” High Performance 7000/5200 2.830” High Performance 8200/6200 3.024” Standard Industrial 6800/5000 2.530” Standard Industrial 7900/6000 2.7

Mfg Part# Size Mount

Wt(lbs)

1/3 HP Industrial High Performance -(fan head & mount)UHP 24-PJR 24” Pedestal 75UHP 24-WJR 24” Wall 45UHP 24-IJR 24 I-Beam 50UHP 24-CJR 24 Ceiling 45UHP 24-SJR 24 Suspension 43

1/4 HP Standard Industrial - (fan head & mount)ACU 24-PJR 24” Pedestal 75ACU 24-WJR 24” Wall 45ACU 24-IJR 24 I-Beam 50ACU 24-CJR 24 Ceiling 45ACU 24-SJR 24 Suspension 43

Mfg Part# Color Description

Wt(lbs)

AccessoriesRS 06-EC Yellow 6’ Extension Cord 1RS 09-EC Yellow 9’ Extension Cord 1.5RS 12-EC Yellow 12’ Extension Cord 2

SCK-12 -- 12’ Safety Cable with Clamps

0.5

R2-MOT Yellow 1/3 HP Motor with drop down switch

1

R3-MOT Yellow 1/4 HP Motor with drop down switch



Local: 972-247-8871


TPI CORPORATIONMaximum Duty Air Circulator Fan Heads


• Safety yellow or gray easy access, powder coated steel hinged guard

• 1/2 HP, 2 speed, 1 phase, 120V ball bearing, totally enclosed perma-nently lubricated permanent split capacitor motor

• Drop down 2 speed switch

• 6’, 9’, or 12’ extension cord options (not included)

• Steel hub/spider alu-minum paddle blades

• Meets OSHA stan-dards

• Intertek listed• 5 year limited war-

ranty

TPI CORPORATIONCirculator Motors

TPI CORPORATIONPedestal Circulator MountsPole & BaseAdjusts the center of fan from 52” to 78” and bolts to 27” diam-eter steel dome base with 5 car-riage bolts.

TPI CORPORATIONWall Circulator Mounts

TPI CORPORATIONI-Beam Circulator Mounts

TPI CORPORATIONCeiling Circulator Mounts

TPI CORPORATIONPedestal Circulator MountsPole & Base• 1/4 HP, 2

speed, 1 phase, 120V ball bearing, totally enclosed per-manently lubricated per-manent split capacitor motor

• Pull chain switch

• SJT type 3 conductor, 12’ long cord

• Steel hub/spi-der aluminum paddle blades

• Coated steel guards

• Compatible mounts include any “ACM” or “CACM” mount

• Meets OSHA standards• 1 Year limited warranty.

TPI CORPORATIONCirculator Wheel Kits

TPI CORPORATIONSpecialty Circulator Heads

• Use with any TPI industrial circulator mount

• Permanently lubri-cated, totally enclosed, ball bear-ing

• Aluminum blades• Steel spiral wire

guards• No cord - junction

box provided for hard wiring


• Intertek listed• 1 year limited warranty• Note: Wash down rated fan heads have

FDA white epoxy coated guards. All other fan heads have chrome plated guards.

Mfg Part# Size Color CFM Amps

ShipWt

(lbs)HDH 24-JR 24” Yellow 8600/6500 3.5 44HDH 30-JR 30” Yellow 9850/7500 4 48

HDH 24-GJR 24” Gray 8600/6500 3.5 44HDH 30-GJR 30” Gray 9850/7500 4 48

Mfg Part# Description Pk

HD-MOT Heavy-Duty 1IHP-MOT High Performance 1AC-MOT Standard Industrial 1

AC-MOT-O Oscillating Industrial 1

Mfg Part# Color Pk

HDM-P Yellow 1ACM-P Gray 1

MfgPart# Color Pk

HDM-W Yellow 1ACM-W Gray 1

Mfg Part# Color PkHDM-I Yellow 1ACM-I Gray 1

Mfg Part# Color Pk

HDM-C Yellow 1ACM-C Gray 1

Mfg Part# Mount CFM Amps Wt (lbs)

Unassembled - all components and mount in one box

ACU 20-P Pedestal 5600/4100 2.4 72

ACU 20-W Wall 5600/4100 2.4 42

Assembled Fan Head OnlyACH 20 none 5600/4100 2.4 39

Mfg Part# Color Pk

HDM-WK Yellow 1ACM-WK Gray 1

Mfg Part# Size Volts Amps CFM

Wt(lbs)

Hazardous Location, Class I Group D, Class IIGroup F & G, Unassembled Heads - 1/4 HPACH 24-EX1 24” 120/240

1-phase 5/2.68000 66

ACH 30-EX1 30” 9200 69ACH 24-EX3 24” 240/480

3-phase 1.4/0.78000 66

ACH 30-EX3 30” 9200 69

Unassembled Heads - 1/4 HPACH-24-TE3 24” 240/480

3-phase 1.4/0.78000 45

ACH-30-TE3 30” 9200 48

Assembled Heads - 1/3 HPIHP 24-H-277 24”

277 1-phase 1

7000/5200

40

IHP 30-H-277 30” 8200/6200

44

Wash down rated, Assembled Head - 1/3 HPIHP 20-H-WD 20”

120/240 1-phase

4.5/2.2

7150 46IHP 24-H-WD 24” 8200 48IHP 30-H-WD 30” 9350 52



Toll-Free: 1-800-462-4983


TPI CORPORATIONCirculator Guards & Blades

TPI CORPORATIONHeavy Duty Square Belt DrivePortable Blowers• 120V, 1-speed, 1-

phase, ball bearing, permanently lubri-cated, ball bearing drip proof motor

• 1/2” shaft• On-Off rocker switch• SJT type 3 conduc-

tor, 12’ long cord• Aluminum blade• Permanently lubricated bearings on blade

drive shaft• Powder coated front and rear guards• Powder coated 20 gauge venturi• 18 gauge galvanized steel housing• Meets OSHA standards• 1 Year limited warranty

TPI CORPORATIONHeavy Duty Direct Drive Blowers

• Totally enclosed and explosion proof motors

• Explosion proof motors are Class 1, Div 1, Group D and Class 2, Div 1, Groups F & G

• Cast aluminum props• 14 Gauge steel body and stand• Acid resistant coating available• Baked enamel coating• 360° Swivel on high and medium stand

units• Meets federal OSHA requirements• 1 year limited warranty

NOTE:Single phase motors are field convertible 115V / 230V. Three phase motors are field convert-ible 230V / 460V. Motors are set to lower volt-age at the factory unless a request is made at time of order to set to the higher voltage.

TPI CORPORATIONConfined Space BlowersGasoline Powered Centrifugal Blower• Powder coated

steel housing with 10 gauge steel base

• Vibration absorbing spring mounted feet

• 8” inlet and out-let

• Uses standard 8” flexible duct• Honda Engine• 18” x 16” x 29” (L x W x H)• 2 Year limited warrantyMay be used in Exhaust Air or Supply Air applications

TPI CORPORATIONConfined Space BlowersElectric Powered Axial Blower w/ Built-in Hose Canister• Rugged plastic

housing• Single speed,

115V, totally enclosed motor

• 15” inlet and 8” outlet

• Uses standard 8” flexible duct• 17” x 16” x 17” (L x W x H)• 1 Year limited warrantyMay be used in Supply Air applications

TPI CORPORATIONConfined Space BlowersAccessories

Mfg Part# Size Color Pk

For 1/2 HP MotorsHD-24GB 24” Yellow 1HD-30GB 30” Yellow 1

For 1/2 HP Heavy-Duty MotorsHD-24GB-C 24” Chrome 1HD-30GB-C 30” Chrome 1

For 1/3 HP & 1/4 HP MotorsAC-24GB 24” Chrome 1AC-30GB 30” Chrome 1

Mfg Part# Size HP CFM Amps

Wt (lbs)

PCBT 36-B 36” 1/2 10,850 8 120

PCBT 42-B 42” 3/4 16,300 11 140

PCBT 48-B 48” 1 22,700 15 185

Mfg Part# Size HP CFM

Wt (lbs) w/ standlow | med | high

MCD18-1/4 18” 1/4 3050 103 145 210

MCD18-1/3 18” 3/4 3450 105 150 215

MCD18-1 18” 1 4600 117 165 230

MCD24-1/4 24” 1/4 5200 115 165 230MCD24-1/3 24” 1/3 5300 126 175 250MCD24-1/2 24” 1/2 6000 120 170 240MCD24-3/4 24” 3/4 6900 140 190 260MCD24-1 24” 1 7400 130 180 250

MCD24-1 1/2 24” 1.5 8200 137 190 255MCD24-3 24” 3 10500 160 210 270

MCD30-1/3 30” 1/3 6900 150 205 260MCD30-1/2 30” 1/2 8900 141 195 250MCD30-3/4 30” 3/4 10400 210 260 320MCD30-1 30” 1 11200 200 260 310

MCD30-1 1/2 30” 1.5 12000 200 250 310MCD30-2 30” 2 14000 225 270 330MCD30-3 30” 3 16000 220 265 325MCD36-1 36” 1 13000 250 320 375

MCD36-1 1/2 36” 1.5 14850 250 320 375MCD36-2 36” 2 17500 255 325 380MCD36-3 36” 3 18500 260 330 390MCD36-5 36” 5 23000 260 330 390MCD42-2 42” 2 19500 315 415 565MCD42-5 42” 5 27000 320 420 570MCD48-5 48” 5 32000 500 620 710

MCD48-7 1/2 48” 7.5 37000 625 745 835MCD48-10 48” 10 41000 682 800 890MCD60-3 60” 3 35000 690 855 965MCD60-5 60” 5 45000 730 895 1005

MCD60-7 1/2 60” 7.5 47000 945 1110 1220MCD60-10 60” 10 57200 1035 1200 1310MCD60-15 60” 15 60750 1080 1245 1355

Mfg Part# HP

CFM Outlet

CFM 1 90°

Bend

CFM 2 90°

BendsWt

(lbs)CSB-8CG-H 4 1350 1050 775 53

Mfg Part# HP

CFM Outlet

CFM 1 90°

Bend

CFM 2 90°

BendsWt

(lbs)CSB-8AE-MC 1/3 1373 740 630 33

Mfg Part# Description

DUCT-8-25 Hose: 8” diameter, 25’ long, 10 lbsHC-8A Carrier: Accommodates hoses up

to 25’ in length and 8-10” diameter



Local: 972-247-8871


TPI CORPORATIONExhaust FansShutter Mounted Direct Drive• Can be installed

from inside wall• Eliminates need for

external framing and shutter

• Pull chain switch• 120V, 1phase,

totally enclosed, permanently lubri-cated motor

• HP: 1/12 - 1/4• No Cord-Junction box provided for direct

wiring• Aluminum blade• Steel spiral wire guards• Fan Sizes: 10” - 30”

TPI CORPORATIONExhaust FansGuard Mounted Direct Drive• Bolts directly to wall• Can be used with or

without external shutter

• Pull chain switch• 120V, 1-Phase,


• HP: 1/12 - 1/4• Fan Sizes: 10” - 30”

TPI CORPORATIONExhaust FansVenturi Mounted Direct Drive• Can be installed

from inside wall• Can be used with

external shutter• Pull chain switch• 120V, 1-Phase,


• HP: 1/12 - 1/4• No Cord-Junction box provided for direct

wiring• Aluminum blade• Steel spiral wire guards• Fan Sizes: 10” - 30”

TPI CORPORATIONCommercial Exhaust FansBelt Drive• 120V, 1-Phase or

230/460V, 3-Phase, ball bearing, per-manently lubri-cated, drip proof motor

• Permanently lubri-cated bearings on blade drive shaft

• Aluminum blade• Powder coated venturi and blade• 1725 RPM• Motor frame size: 56• 5/8” shaft• Fan Sizes: 24” - 48”• 1 year warranty

TPI CORPORATIONHeavy Duty Exhaust FansBelt Drive• Totally enclosed

and explosion proof motors are Class 1, Div 1 Group D and Class 2, Div 1, Groups F & G

• Fans are shipped completely assem-bled

• Heavy gauge steel blades on TEC models

• Cast aluminum blades on EXP explosion proof models

• 14 gauge steel panel with welded steel pipe bracing

• Blade Sizes: 24” - 60”• 1 year warranty

TPI CORPORATIONHeavy Duty Exhaust FansDirect Drive• Totally enclosed

and explosion proof motors are Class 1, Div 1 Group D and Class 2, Div 1, Groups F & G

• Fans are shipped completely assem-bled

• Cast aluminum blades

• 14 gauge steel panel with welded steel pipe bracing


TPI CORPORATIONIndustrial Exhaust FansBelt Drive• Totally enclosed 1-

Phase and 3-Phase motors

• 16 Gauge steel venturi with steel pipe bracing

• Steel blades• Double pillow block

bearing shaft sup-port

• Blade Sizes: 24” - 60”

• 1 year warranty

TPI CORPORATIONIndustrial Exhaust FansDirect Drive• Totally enclosed 1-

Phase and 3-Phase motors

• 14 Gauge steel venturi with steel pipe bracing

• 4-blade steel pro-peller

• Blade Sizes: 12” - 48”

• 1 year warranty

TPI CORPORATIONCabinet Exhaust Fanswith Shutters• 120V, 1-Phase or

230/460V, 3-Phase, ball bearing, perma-nently lubricated, drip proof motor

• Permanently lubri-cated bearings on blade drive shaft

• Aluminum blade• Aluminum shutter• 20 Gauge powder coated venturi• 18 Gauge galvanized steel housing• 1725 RPM• Motor frame size: 56• 5/8” shaft• Fan Sizes: 24” - 48”• UL Listed• Ships fully assembled• Package options available that includes

wall collar, rear box guard, and automatic shutter

• Meets OSHA Standards• 1 year warranty



Toll-Free: 1-800-462-4983


TPI CORPORATIONRoof VentilatorsBelt Drive• Standard blades are

heavy gauge steel• Totally enclosed 1-

Phase or 3-Phase motors

• Wind band is 18 gauge galvanized steel

• Galvanized steel butterfly damper with rub-ber stops and seals


TPI CORPORATIONRoof VentilatorsDirect Drive• Cast aluminum

blades on most models

• Totally enclosed 1-Phase and 3-Phase motors

• Explosion proof motors are Class 1, Div 1, Group D and Class 2, Div 1, Groups F & G

• Wind band is 18 Gauge galvanized steel• Rubber shim under dampers for better seal• Blade Sizes: 18” - 60”• 1 year warranty

TPI CORPORATIONAttic FansPower Attic Mount Dome Ventilator• 120V Motor/1-Phase• Safety fire link pro-

tected• Automatic thermo-

stat (90°-130°F)• Insect and bird

screen installed• Powder coated metal dome and base

TPI CORPORATIONAttic FansBelt Drive Wholehouse Fan• 120V, 1-Phase, 2-

Speed motor• Shutters automati-

cally open when fan is turned off

NOTE: “No Joist Cut” Shutter

TPI CORPORATIONIndustrial Ceiling FansCommercial / Industrial / Heavy Duty• All metal con-

struction; white epoxy finish

• 24” Down rod with safety cable

• Mounts to 3/8” diameter steel J-hook• 18 pole, 115V, 1-Phase, Capacitor type,

impedance protected motor with sealed ball bearings

• Optional or other down rod length available

* 277 volt, commercial, and reversing models have lead wires instead of cordset; WR in model number indicates Water and Dust Resistant Models

TPI CORPORATIONPortable 18” Self ContainedPower MisterWater Pumped from 10gal. Cooler• Toggle Switch -

fan only or fan & mist

• 1-Speed, 1/8 HP, 1-Phase, 120V, totally enclosed, sleeve bearing, permanently lubricated, per-manent split capacitor motor.

• SJT type cord - 3 conductor - 18’ long• Power cutoff tip switch and GFCI plug for

extra safety• 18” Aluminum blad• Spiral front and rear wire guards• 85 psi diaphragm pump• Meets OSHA standards / 1 year limited

warrantyNOTE: Cooler lid not included

TPI CORPORATIONIndustrial Workstation Floor Fans• Rotary switch• Head tilts 360°• Coated steel

guards• SJT type 3 con-

ductor, 10’ long cord

• Steel hub/spi-der aluminum paddle blades

• 3-Speed, 120V, 1-Phase, totally enclosed, sleeve bearing, permanently lubricated motor

• 5/16 shaft• Intertek Listed• Meets OSHA standards• 1 Year limited warranty

Mfg Part#

DomeColor

CFM.03 SP HP

Wt(lbs)

PDV-305-1MB-Gy Gray 1080 1/12 18

PDV-305-1MB-Br Brown 1080 1/12 18PDV-305-1MB-Blk Black 1080 1/12 18

Mfg Part# Size CFM HP

Wt(lbs)

BD24-2-WHS 24” 4500/2700 1/3 40

BD30-2-WHS 30” 7600/5800 1/3 50BD36-2-WHS 36” 9675/6400 1/3 64

Mfg Part# Size Type CFM Volts

Wt(lbs)

Commercial Grade - assembly required, 30” lead wires, 1 year warranty

CHR-56 56” Down Draft 19000 120 15

Industrial Grade - fully assembled except blade bolt down, 3 conductor cord, 30” long with plug, permanently lubricated, 3 year limited warranty

IHR-48 48” Down Draft 17100 120 14IHR-56 56” Down Draft 21000 120 15

IHR-56R 56” Reversible 21000 120 14IHR-56-277V 56” Down Draft 21000 277 16

Heavy Duty Grade - fully assembled except blade bolt down, 3 conductor cord, 30” long with plug, permanently lubricated, 6 year limited warranty

HDHR-56 56” Down Draft 27500 120 18HDHR-60 60” Down Draft 47000 120 21

HDHR-56WR 56” Down Draft 27500 120 17HDHR-60WR 60” Down Draft 47000 120 21

Mfg Part# Type HP CFM Amps

Wt(lbs)

PM-18S HandCarry

1/8 5750 2.2 30

PM-18C Cart 1/8 5750 2.2 38

Mfg Part# Description

Wt(lbs)

PM-18FO 18” Fan & Pump Lid for10gal. Cooler

28


MaxAmps

Wt(lbs)

Floor ModelF-12-TE 12” 1/12 1650/1120 1.1 13F-18-TE 18” 1/8 4600/3200 1.5 20F-24TE 24” 1/8 5850/3600 2.4 23

High StandF-18H-TE 18” 1/8 4600/3200 2.2 27F-24H-TE 24” 1/8 5850/3600 2.4 30



Local: 972-247-8871


TPI CORPORATIONCommercial Workstation Floor Fans• Rotary switch• Coated steel guards

with retaining clips• SJT type 3 conduc-

tor, 7’ long cord• Aluminum blade• 3-Speed, 120V, 1-

Phase, open venti-lated, sleeve bear-ing, permanently lubricated motor

• UL Listed• Meets OSHA standards• 1 Year limited warranty

TPI CORPORATIONIndustrial Mounted Workstation Fans• Pull chain switch• Head rotates 360°

vertical and horizon-tal direction

• Coated steel guards• SJT type 3 conduc-

tor, 10’ long cord• Steel hub/spider

aluminum paddle blades

• 3-Speed, 120V, 1-Phase, totally enclosed, sleeve bearing, perma-nently lubricated motor

• 5/16 shaft• Intertek Listed• Meets OSHA standards• 1 Year limited warrantyNOTE: Mount with one bolt or lag screw to walls, ceilings, work benches, machines or any surface.

TPI CORPORATIONWorkstation Wall Mount Fan18” High Velocity Fan Mounted on 24”, 40” or 60” Pivoting Arms• 18”high veloc-

ity circulator, with 3 speed, 1/8 HP, 115V, 1-Phase per-manently lubri-cated, totally enclosed, PSC motor

• Modular fan plugs into electrical outlet on arm

• Coated steel guards/Aluminum blades• Intertek Listed• Meets OSHA standards• 1 Year limited warranty

Mounting Arm Features:• 1-1/2” square, 14 gauge, steel tubing• 3” x 5” x 3/16” mounting plate attaches with

(4) 3/8” bolts• 5’ long, 18/3 SJTW conductor cord and

NEMA 5-15 grounded plug• Dual electrical outlets embedded in arm to

allow connection of modular fan and optional light

Optional Modular Light Features:• Plugs into embedded outlet in arm• On/Off switch and wire guard included• Bulb included with DKL-QH and DKL-FL

TPI CORPORATIONWorkstation Oscillating Office Fans• 3-speed oscillating

fans with push but-ton controls

• 3 conductor SPT cord & plug

• White powder coated wire mesh guards

• White plastic hous-ing and blade

• Stand fan extends to 40” height

• UL Listed• Meets OSHA standards• 1 Year limited warranty

TPI CORPORATIONLow Velocity “Navy Style”Workstation Fan• 12” all metal, gray

powder coated fan that can be wall, ceil-ing or bench mounted

• Direct wire electrical connection

• Toggle switch• Fan head tilts 90° in

horizontal and verti-cal planes


• 1 Year limited warranty


MaxAmps

Wt(lbs)

CF-12 12” 1/12 2100/1500 0.6 10CF-18 18” 1/5 3150/2550 1.4 16CF-20 20” 1/5 3450/2950 1.9 18CU-20 20” 1/5 3450/2950 1.9 18


MaxAmps

Wt(lbs)

U-12-TE 12” 1/12 1650/1120 1.1 13U-18-TE 18” 1/8 4600/3200 2.2 20U-24-TE 24” 1/8 5850/3600 2.4 23

Pipe Mount AdaptorPM-1 1” pipe diameter

PM-1.5 1-1/2” pipe diameterPM-2 2” pipe diameter

PM-2.5 2-1/2” pipe diameterPM-3 3” pipe diameter

Mfg Part#

FanSize

ArmLength CFM

MaxAmps

Wt(lbs)

24-LDF-TE 18” 24” 5750/3200 2.2 31

40-LDF-TE 18” 40” 5750/3200 2.2 3860-LDF-TE 18” 60” 5750/3200 2.2 44

Mfg Part#

Light HeadType

MaxWatts

MaxLumens

BulbLife(hrs)

Wt(lbs)

DKL-INC Incandescent 300 3,700 2,000 5

DKL-QH QuartzHalogen

500 11,000 2,000 6

DKL-FL Fluorescent 55 3,000 10,000 7DKL-LED LED 12 960 50,000 5

Mfg Part# Type Size CFM

AmpsHigh

Wt(lbs)

ODF-12 Desk 12” 1200 0.4 5.4

ODF-16 Desk 16” 2100 0.5 8.5OSF-16 Stand 16” 2100 0.5 15.5

Mfg Part# Size

MotorHP CFM

AmpsHigh

Wt(lbs)

N-12 12” 1/12 1540/930 0.6 12




Toll-Free: 1-800-462-4983


TPI CORPORATIONPortable WorkstationEvaporative CoolersEvap-Mini Features:• Lowers tempera-

tures up to 30°F• Water level sight

tube and sump drain

• 3/4” garden hose connection for lon-ger running

• Durable one-piece, rust free, leak-proof molded polyeth-ylene housing

• Environmentally friendly efficient and effec-tive resource use

• Cools for a fraction of the cost of air condi-tioning

• Cools without chemicals or refrigerants• Long-term dependability-near mainte-

nance-free operation• Shipped completely assembled, ready to

operated out of the box]

TPI CORPORATIONHeavy-Duty Portable Evaporative Coolers16”, 24”, 36”, and 48”

• Liquid level indicator with automatic pump shut off

• When pump is deenergized, red LED indi-cator light is on

• Heavy duty casters• Variable speed motors• Built in handles for easy moving• Two inch drain for convenient flushing and

cleaning

TPI CORPORATIONHeavy-Duty Portable Evaporative Coolers36” and 48”

• 36” model cools 2,500 sq. ft. and holds 32 gallons of water

• 48” model cools 4,000 sq. ft. and holds 40 gallons of water

• All switches, motors, and cord connec-tions are sealed to prevent sparking in combustible locations

• Shipped completely assembled, ready to use

• 120/240V operation• Manufactured in U.S.A.• Component Rating: Class 1A, Division D

for Hazardous Location

Mfg Part# Sq Ft HP Amps CFM GalWt

(lbs)EVAP-Mini 700 700 1/3 5.6 3000/2400 16 113

Mfg Part# SizeEffectiveSq. Ft. Amps CFM

Wt(lbs) Pk

EVAP16HD 16 "1,125 5.4 4,500 152 1EVAP24HD 24 "2,125 9.2 8,500 213 1EVAP36HD 36 "3,125 15 12,500 267 1EVAP48HD 48 "5,625 20 22,500 375 1

Mfg Part# HP Amps CFMWt

(lbs) PkEVAP36-HAZ 1/2 13.4 9600 330 1EVAP48-HAZ 1 18 20,000 460 1



Local: 972-247-8871


TPI CORPORATIONHazardous Location Fan Forced Unit Heater3-25KW for Class I, Group C & D, Divi-sion 1 & 2 and Class II, Groups E, F & G, Divisions 1 & 2.• Designed for rugged industrial applica-

tions in hazardous locations where the possibility of explosion or fire exists due to the presence of certain flamma-ble gases, vapors, powdered metals or dust.

• Permanently sealed, liquid to air, finned tube heat exchanger core.

• Ethylene Glycol to water mixture used as a heat transfer fluid in the heater core, providing -45°C (-49°F) freeze damage protection.

• High-performance electric motor driven fan blows air across finned tubes to effect uniform heat transfer and area heat distribution.

• Manual Reset capillary type limit provides high temperature regula-tion and is rated for 6,000 cycles of service.

• Stainless steel and aluminum pressure relief valve for overpressure.• A back-up contactor is included for additional protection.• 14 Gauge steel cabinet powder coated epoxy paint finish contains

heater core, motor, and fan assembly.• Narrow gap safety fan guard shields all moving parts.• Adjustable louvers allow directional control of air.• Copper conductor wires enclosed in rigid metal conduits carry all

electrical power.• Box lugs furnished for field connections within approved enclosure.• Flexible mounting kits allow unit to be mounted on a pipe, overhead

structure, or wall.

* Photo shows optional pilot light and disconnect switch.

TPI CORPORATIONPortable Hazardous Location Fan Forced Unit HeaterSame features as HLA Series (shown in left column).• Wheeled cart allows for easy maneu-

verability• Anti-static wheels reduce the risk of

static discharge• Integrated fork-lift channels on cart

provide ease of lifting onto ramps or trucks

• Excellent for providing seasonal heat-ing in hazardous environments

• All units have disconnect switch, pilot light, and thermostat - standard

• 24 Volt control, transformer, and con-tactor in NEMA 7 enclosure

• Durable epoxy coating on heater housing• Hazardous location unit mounted male/female plug• Adjustable louvers; manual reset

* Use Table in Left Column (HLA Series) as reference - Portable model part numbers begin with a Prefix of “P” and a Suffix of “-TDP” For exam-ple, the non-portable part #HLA 12-208160-3.0-24 becomes portable model part #PHLA 12-208160-3.0-24-TDP.

TPI CORPORATIONFan Forced Milkhouse Heater110V Portable

• 1300W & 1500W heat settings plus fan only setting

• Temperature control thermostat• 6' long, 3 conductor cord• Triple safety system: 1) Tip over switch,

2) Automatic reset type limit control, 3) Thermal cut-off device

• UL and cUL listed

TPI CORPORATIONCeramic Fan Forced Heater120V Portable

• 850W & 1500W heat settings plus fan only setting

• Automatic reset type limit control• Thermal cut-off device• 6' long, 3 conductor cord• Temperature control thermostat• UL and cUL listed

Mfg Part# KW BTU’s Volts Phase Amps

Air Throw CFM

Recom’ Mount Height

Wt (lbs)

HLA 12-208160-3.0-24 3 10250 208 1 16.3 24’ 580 8’ 167HLA 12-208360-3.0-24 3 10250 208 3 9.8 24’ 580 8’ 167HLA 12-240160-3.0-24 3 10250 240 1 14.8 24’ 580 8’ 167HLA 12-240360-3.0-24 3 10250 240 3 8.6 24’ 580 8’ 167HLA 12-480360-3.0-24 3 10250 480 3 4.3 24’ 580 8’ 167HLA 12-208160-5.0-24 5 17100 208 1 26 24’ 580 8’ 167HLA 12-208360-5.0-24 5 17100 208 3 15.4 24’ 580 8’ 167HLA 12-240160-5.0-24 5 17100 240 1 23.1 24’ 580 8’ 167HLA 12-240360-5.0-24 5 17100 240 3 13.4 24’ 580 8’ 167HLA 12-480360-5.0-24 5 17100 480 3 6.7 24’ 580 8’ 167HLA 12-208160-7.5-24 7.5 25600 208 1 38 24’ 580 8’ 167HLA 12-208360-7.5-24 7.5 25600 208 3 22.3 24’ 580 8’ 167HLA 12-240160-7.5-24 7.5 25600 240 1 33.6 24’ 580 8’ 167HLA 12-240360-7.5-24 7.5 25600 240 3 19.4 24’ 580 8’ 167HLA 12-480360-7.5-24 7.5 25600 480 3 9.7 24’ 580 8’ 167

HLA 16-208360-10.0-24 10 34150 208 3 29.3 40’ 1500 10’ 193HLA 16-240160-10.0-24 10 34150 240 1 44 40’ 1500 10’ 193HLA 16-240360-10.0-24 10 34150 240 3 25.5 40’ 1500 10’ 193HLA 16-480360-10.0-24 10 34150 480 3 12.7 40’ 1500 10’ 193HLA 20-208360-15.0-24 15 51200 208 3 43.5 43’ 2450 13’ 193HLA 20-240360-15.0-24 15 51200 240 3 38.1 43’ 2450 13’ 193HLA 20-480360-15.0-24 15 51200 480 3 19 43’ 2450 13’ 193HLA 20-600360-15.0-24 15 51200 600 3 15.2 43’ 2450 13’ 193HLA 20-480360-20.0-24 20 68300 480 3 25.1 43’ 2450 13’ 225HLA 20-600360-20.0-24 20 68300 600 3 20 43’ 2450 13’ 225HLA 20-480360-25.0-24 25 85400 480 3 31.1 43’ 2450 13’ 225HLA 20-600360-25.0-24 25 85400 600 3 24.9 43’ 2450 13’ 225

Mfg Part# Dimensions

MaxBTU’s Phase

Wt(lbs) Pk

188 TASA 10”x16”x9.5” 5120 1 9 1


MaxBTU’s Phase

Wt(lbs) Pk

178 TMC 11.25”x10”x7” 5120 1 8 1



Toll-Free: 1-800-462-4983


TPI CORPORATION5500 Series Washdown Fan Forced Unit HeaterElectric unit heater constructed for use in areas that require washing or hosing of equipment due to dirty or dusty industrial environments in non-hazardous locations. The totally enclosed water-tight construction made with corro-sion-resistant material make this series ideal for industrial heating applications. The Washdown Series is con-structed with all built-in controls and safety temperature controls wired in a non-metallic Nema 4x control panel with single-point power connections.• Heavy-duty 304 16 Gauge stainless steel shroud (316 available)• Nema 4x non-metallic control panel• 24-Volt transformer and control panel• 3-position switch (off-heat-fan)• Capillary thermostat with stainless steel sensor• Automatic reset thermal cutout• Totally enclosed U.L. listed motor• Pilot light (power on indicator)• Stainless steel finned tubular element, constructed of 304 or 316 stainless rod and fins• Control panel on bottom of unit for ease of installation and service• Disconnect switch with enclosure door interlock• Front grill rotates to direct airflow• Single-point power connection• Fan blade epoxy coated aluminum• Epoxy painted cold roll steel model available - consult factory• Meets all U.L., NEC, and OSHA requirements (when installed as directed)• Corrosion-resistant in high humidity and water-saturated areas (for areas where corrosion

resistance is needed in non-explosive areas, contact factory for heater applications and optional materials)

• ABS (American Bureau of Shipping) type approved

(for 5500 Series Washdown Fan Forced Unit Heater)TPI CORPORATIONPump House Convection HeatersProvides protection against freezing for pump houses, utility rooms, relay sta-tions, construction sheds, etc.• Aluminum finned heating element• Powder coated epoxy steel case• Automatic temperature control ther-

mostat with a 35°F-65°F range• 20”x5-1/2”x4”

MfgPart# KW BTU’s Volts Phase Amps

Temp Rise °F

Air Throw CFM

Wt (lbs)

MfgPart# KW BTU’s Volts Phase Amps

Temp Rise °F

Air Throw CFM

Wt (lbs)

F1F5503T 3.3 11200 208 1 15.9 26 20’ 400 58 H1H5510T 10 34130 240 1 41.2 45 28’ 700 64F3F5503T 3.3 11200 208 3 9.2 26 20’ 400 58 H3H5510T 10 34130 240 3 24.1 45 28’ 700 64H1H5503T 3.3 11200 240 1 13.7 26 20’ 400 58 G1G5510T 10 34130 277 1 36.1 45 28’ 700 64H3H5503T 3.3 11200 240 3 7.9 26 20’ 400 58 P3P5510T 10 34130 480 3 12.1 45 28’ 700 64G1G5503T 3.3 11200 277 1 11.9 26 20’ 400 58 F1F5515T 15 51200 208 1 72.1 68 28’ 700 64P3P5503T 3.3 11200 480 3 4 26 20’ 400 58 F3F5515T 15 51200 208 3 41.7 68 28’ 700 64F1F5505T 5 17100 208 1 24.1 40 20’ 400 58 H1H5515T 15 51200 240 1 62.5 68 28’ 700 64F3F5505T 5 17100 208 3 13.9 40 20’ 400 58 H3H5515T 15 51200 240 3 36.1 68 28’ 700 64H1H5505T 5 17100 240 1 20.8 40 20’ 400 58 P3P5515T 15 51200 480 3 18.1 68 28’ 700 64H3H5505T 5 17100 240 3 12.1 40 20’ 400 58 F3F5520T 20 68260 208 3 55.6 45 35’ 1400 92G1G5505T 5 17100 277 1 18.1 40 20’ 400 58 H3H5520T 20 68260 240 3 48.2 45 35’ 1400 92P3P5505T 5 17100 480 3 6.1 40 20’ 400 58 P3P5520T 20 68260 480 3 24.1 45 35’ 1400 92F1F5507T 7.5 25600 208 1 36.1 60 20’ 400 58 F3F5525T 25 85325 208 3 69.5 56 35’ 1400 92F3F5507T 7.5 25600 208 3 20.8 60 20’ 400 58 H3H5525T 25 85325 240 3 60.2 56 35’ 1400 92H1H5507T 7.5 25600 240 1 31.3 60 20’ 400 58 P3P5525T 25 85325 480 3 30.1 56 35’ 1400 92H3H5507T 7.5 25600 240 3 13.1 60 20’ 400 58 F3F5530T 30 102390 208 3 83.4 68 35’ 1400 92G1G5507T 7.5 25600 277 1 27.1 60 20’ 400 58 H3H5530T 30 102390 240 3 72.3 68 35’ 1400 92P3P5507T 7.5 25600 480 3 9.1 60 20’ 400 58 P3P5530T 30 102390 480 3 36.1 68 35’ 1400 92F1F5510T 10 34130 208 1 47.8 45 28’ 700 64 P3P5540T 40 136520 480 3 48.2 70 42’ 1800 126F3F5510T 10 34130 208 3 27.7 45 28’ 700 64 P3P5548T 48 163824 480 3 57.8 84 42’ 1800 126

Size KW

Stainless SteelCombination Bracket

Wall MtgBracket*

HangingBracket*

Pipe MtgBracket*

Mounting Bracket Kits & Product Dimensions3.3-15 A5520/UHB W5520/WMK H5520/HMK P5520/PMK20-48 ---- W5550/WMK H5550/HMK P5550/PMK

Mfg Part# Watts BTU’s Volts Amps Wt (lbs) PkRPH1-5A 500 1706 120 4.2 5 1

RPH2-5A 500 1706 240 2.1 5 1



Local: 972-247-8871


TPI CORPORATIONDual Heat Fan Forced Heater240V Portable

• 2000W & 4000W heat settings• Temperature control thermostat• Manual reset type limit control• 6' long, 3 conductor cord• 20 amp plug configuration, NEMA

#6-20P• ETL listed

TPI CORPORATIONFan Forced Unit Heater240/208V Portable

• Swivel base can be used as a wall, floor or ceiling mount.

• Operates on 240V or 208V• Finned steel tubular heating element• Internal manual reset thermal cut-out• 13.5”x17.5”x11.5”• 6' long cord with molded plug• Temperature control thermostat with

35°F to 85°F range• 10’ air throw• Phase 1, 262 CFM• 20 amp plug configuration, NEMA #6-20P & 30 amp plug configura-

tion, NEMA #6-30P• UL and cUL listed (HF684TC UL listed only)

TPI CORPORATIONConstruction Site/ Utility Fan Forced Heater240/208V Portable

• Operates on 240V or 208V• Steel tubular heating element• 43°F air heat rise• 6' long cordset• Internal overheat thermostat• Temperature control thermo-

stat• 20 amp plug configuration,

NEMA #6-20P• 10.625”x12.75”x10”• UL listed

TPI CORPORATIONCombination Radiant & Fan Forced Heater120V Portable

• 3-Heat settings: 1) 600W radiant, 2) 900W fan forced, 3) 1500W radiant & fan forced

• Temperature control thermostat• Dual safety system: 1) Tip over switch, 2)

Manual reset type limit control• 6' long, 3 conductor cord• 11”x15”x12”• UL and cUL listed

TPI CORPORATIONWall/Ceiling Mount Electric Salamanders

• Wall/ceiling mount included• Ready for direct wiring• Termostat adjustment 40° to 100°F• ETL listed

TPI CORPORATIONPortable Electric SalamandersHeat Wave™The electric alternative to propane and kerosene space heaters.

• Safety yellow heater enclosure with safety screens on air intake & output

• Long-life finned tubular heating elements• Thermostat adjustment 40° to 100° F• Two 10” rear wheels and a front locking

caster• High-limit thermal cutout switch with

manual reset• 2200 CFM• Fan only operation feature• ETL Listed


MaxBTU’s Phase

Wt (lbs) Pk

H474 TMC 16”x16”x8.5” 13652 1 20 1

Mfg Part# Watts

Max BTU’s Amps

Temp Rise

Wt (lbs) Pk

HF684TC 4000/3000

13652/10239

16.7/14.5

48°F 20 1

HF685TC 4800/3600

16384/12288

20.0/17.4

58°F 20 1

HF686TC 5600/4200

19107/14330

23.4/20.2

75°F 20 1

Mfg Part# Watts

MaxBTU’s Phase

Wt(lbs) Pk

ICH-240C 4000/3000 13648 1 15 1

Mfg Part# Watts

MaxBTU’s Phase

Wt(lbs) Pk

198 TMC 1500/900/600 5120 1 9 1

Mfg Part# Volts Phase Amps

TempRise

Wt(lbs) Pk

15KW - 51,195 BTU’sYES-1520-3A 208 3 42 45°F 60 1YES-1524-1A 240 1 63 45°F 60 1YES-1524-3E 240 3 36 45°F 60 1YES-1548-3E 480 3 18 45°F 60 1

30KW - 102,390 BTU’sYES-3048-3A 480 3 36 90°F 72 1


TempRise

Wt(lbs) Pk

FES-4548-3 480 3 54.2 70°F 125 1FES-4560-3 600 3 44 70°F 83 1



Toll-Free: 1-800-462-4983


TPI CORPORATIONPortable Electric SalamandersHeat Wave™The electric alternative to propane and kerosene space heaters.

• Safety yellow heater enclosure with safety screens on air intake & output

• Optional 25’ long SO type cord, ready for plug attachment, is available for each model

• Long-life finned tubular heating elements• Thermostat adjustment 40° to 100° F• Magnetic contactor• Automatic reset• High-limit thermal cutout switch• Fan only switch• 10” wheels• 800 CFM-15KW units; 1100 CFM-30KW

units• ETL Listed

AVG TEMP RISE(based on 15’ ceiling) @ 15 KW FOR:1000 sq ft: 20°F = 47 min, 40°F = 94 min1500 sq ft: 20°F = 71 min, 40°F = 142 min2000 sq ft: 20°F = 94 min, 40°F = 188 min

AVG TEMP RISE(based on 15’ ceiling) @ 30 KW FOR:1000 sq ft: 20°F = 23 min, 40°F = 46 min1500 sq ft: 20°F = 35 min, 40°F = 70 min2000 sq ft: 20°F = 47 min, 40°F = 94 min

TPI CORPORATIONOptional 25’ Power CordsHeat Wave™

TPI CORPORATIONPortable Baseboard Convection Heater120V

• 1500 Watt convection heater

• Temperature control ther-mostat

• Manual reset type limit control

• Power on indicator light• 6’ long, 3 conductor cord• 48”x5-1/4”x7-1/2”• ETL listed

TPI CORPORATION“Under-The-Desk” Confined Space Radiant Heat Panel120V

• Use under desks for personal com-fort or in small areas for freeze pro-tection or moisture removal

• Built-in stand• Temperature control thermostat• 6’ long, 3 conductor cord• ETL listed

TPI CORPORATIONPortable Electric Infrared HeatersHeavy-Duty Metal SheathStand

• Double side wall housings to reduce operat-ing temperatures

• 60° symmetrical heat pattern• Factory installed U-shaped metal sheath

infrared heating elements have an average 5000 hour life

• Heavy-duty protective wire screens• Gold anodized aluminum internal reflector• Ground fault protection must be used• Optional 25’ long SO type cord, ready for

plug attachment, is available for each model


TempRise

Wt(lbs) Pk

15KW / 800CFM / 51,195 BTU’s – Optional 25’ long SO type cord, ready for plug attachmentFES-1520-3A 208 3 42 45°F 65 1FES-1524-1A 240 1 63 45°F 69 1FES-1524-3E 240 3 36 45°F 65 1FES-1548-3E 480 3 18 45°F 65 1

30KW / 1100CFM / 102,390 BTU’s – Optional 25’ long SO type cord, ready for plug attachmentFES-3048-3A 480 3 36 90°F 83 1FES-3060-3A 600 3 29 45°F 65 1

10KW Factory pre-wired with 10ft. cable and straight blade range plugFES-0924-1C 240 1 38 25°F 55 1

FES-1024-1CA 240 1 42 30°F 60 1

Mfg Part# Type For Use With

316408 6/4 SO FES-1520-3A, FES-1524-3E, FES-3048-3A & FES-4560-3

880510 4/3 SO FES-1524-1A

316422 12/4 SO FES-1548-3E & FES-3060-3A

316439 4/4 SO FES-4548-3

Mfg Part# Watts

MaxBTU’s Phase

Wt(lbs) Pk

483 TM 1500 5120 1 13 1

Mfg Part# Watts

MaxBTU’s Phase

Wt(lbs) Pk

170-TS 170 580 1 9 1


Wt(lbs) Pk

Standard Models – No Cord IncludedFHK-224-1A 2.0 6826 240 1 8.3 17 1FHK-248-1A 2.0 6826 480 1 4.2 17 1FHK-424-1A 4.5 15359 240 1 18.8 24 1FHK-448-1A 4.5 15359 480 1 9.4 24 1

Factory Pre-Wired with 15-ft. Cord & Grounded PlugFHK-212-1CA 1.8 6143 120 1 15 18 1



Local: 972-247-8871


TPI CORPORATIONPortable Electric Infrared HeatersHeavy-Duty Metal SheathHand Cart

• Double side wall housings to reduce operating temperatures

• Double top baffles to reduce operating temperatures

• 60° symmetrical heat pattern• Factory installed U-shaped metal

sheath infrared heating elements have an average 5000 hour life

• Heavy-duty protective wire screens• Gold anodized aluminum internal

reflector• Ground fault protection must be used• Optional 25’ long SO type cord, ready

for plug attachment, is available for each model

TPI CORPORATIONOptional 25’ Power CordsPortable Electric Infrared Heaters

TPI CORPORATIONQuartz Infrared HeaterChain Mount or Cart UnitHas (2) 1000W elements that can be switched on/off by toggle switches to produce 1000W or 2000W of heat.• 15’ cord with NEMA 5-20 20-Amp

molded plug• 60° symmetrical heat pattern • Quartz tubes and built in wire

guards included• Interior or protected outdoor use only • Gold anodized aluminum reflector and end caps

TPI CORPORATIONQuartz Infrared HeaterChain Mount or Cart UnitHas (2) sets of 1425W elements that can be switched on/off by toggle switches to produce 2850W or 5700W of heat.• 15’ cord with NEMA 6-30P 30-Amp

twist lock plug• 60° symmetrical heat pattern • Quartz tubes and built in wire guards

included• Interior or protected outdoor use only • Gold anodized aluminum reflector and

end caps

TPI Heaters are manufactured in the U.S.A.

Every aspect of the TPI manufacturing process isgoverned by pride of craftsmanship that has ledTPI to create a majority of its own components.This complete competancy allows TPI to manu-facture almost anything HVAC or lighting related.


Wt(lbs) Pk

6.0KW – 20,478 BTU’sFHK-624-3A 240 3/1 14.4/25.0 37 1FHK-648-3A 480 3/1 7.5/13 37 1

13.5KW – 46,076 BTU’sFHK-1324-3A 240 3 33.0 65 1FHK-1348-3A 480 3/1 17.0/29.0 65 1

Mfg Part# Type

For UseWith

880435 16/3 SO FHK-224-1A & FHK-248-1A880459 12/3 SO FHK-424-1A880466 14/3 SO FHK-448-1A &

FHK-648-3A (480V, 1PH)880497 14/4 SO FHK-624-3A (240V, 3PH)

& FHK-648-3A (480V, 3PH)880442 10/3 SO FHK-624-3A (240V, 1PH)880510 8/4 SO FHK-1324-3A316422 12/4 SO FHK-1348-3A (480V, 3PH)880527 8/3 so FHK-1348-3A (480V, 1PH)


Wt(lbs) Pk

CH-2212-1C 2.0/1.0 6,826 / 3,413 120 1 16.7/8.35 16 1


Wt(lbs) Pk

CH-6424-1C 5.7/2.85 19454/9727 240 1 23.8/11.9 31 1FHK-1 OPTIONAL CART 20 1



Toll-Free: 1-800-462-4983


TPI CORPORATIONSingle- and Three-Phase Hazardous Location Wall Convector

• Cabinet size 18” high, 9” wide• Bottom In – Front Out air flow• Wall mounting bracket supplied• Units cannot be operated in room ambients exceeding 104°F (40°C)• Heavy duty 16 Gauge steel with gray epoxy textured powder coated finish• 9” minimum clearance from bottom of heater to floor required• Stainless steel cartridge element inserted into aluminum finned copper sheath• Standard unit (without EPET thermostat or control section) is NEMA 4 rated• ETL listed

Factory Installed Control Options

* Remove RA suffix and add new suffix. Suffix “T” is 22 Amps maximum.** Not NEMA washdown rated or rated for Group B atmospheres. C1-TD and C1-TDP are the only options available for 3 phase units.

MfgPart# Watts BTU’s Volts Amps

CabinetLength

Wt (lbs)


CabinetLength

Wt (lbs)

T-2A Series Single Phase280°C / 536°F – Class 1, Group B, C & D, Divisions 1 & 2

T-3A Series Single Phase180°C / 356°F – Class 1, Group B, C & D, Divisions 1 & 2

FEP-1812-1RA 1800 6143 120 15 34” 50 FEP-0812-1RA 800 2730 120 6.7 34” 50FEP-1820-IRA 1800 6143 208 8.7 34” 50 FEP-0820-1RA 800 2730 208 3.8 34” 50FEP-1824-1RA 1800 6143 240 13.7 34” 50 FEP-0824-1RA 800 2730 240 3.3 34” 50FEP-1827-1RA 1800 6143 240 7.9 34” 50 FEP-0827-1RA 800 2730 277 2.9 34” 50FEP-1848-1RA 1800 6143 277 11.9 34” 50 FEP-0848-1RA 800 2730 480 1.7 34” 50FEP-3620-1RA 3600 12286 480 4 34” 54 FEP-1612-1RA 1600 5460 120 13.3 34” 54FEP-3624-1RA 3600 12286 208 24.1 34” 54 FEP-1620-1RA 1600 5460 208 7.7 34” 54FEP-3627-1RA 3600 12286 208 13.9 34” 54 FEP-1624-1RA 1600 5460 240 6.7 34” 54FEP-3648-1RA 3600 12286 240 20.8 34” 54 FEP-1627-1RA 1600 5460 277 5.8 34” 54FEP-3657-1RA 3600 12286 240 12.1 34” 54 FEP-1648-1RA 1600 5460 480 3.3 34” 54FEP-3820-1RA 3800 12969 277 18.1 58” 80 FEP-1657-1RA 1600 5460 600 2.7 34” 54FEP-3824-1RA 3800 12969 480 6.1 58” 80 FEP-1712-1RA 1700 5802 120 14.2 58” 80FEP-3827-1RA 3800 12969 208 36.1 58” 80 FEP-1720-1RA 1700 5802 208 8.2 58” 80FEP-3848-1RA 3800 12969 208 20.8 58” 80 FEP-1724-1RA 1700 5802 240 7.1 58” 80FEP-7620-1RA 7600 25938 240 13.1 58” 85 FEP-1727-1RA 1700 5802 277 6.1 58” 80FEP-7624-1RA 7600 25938 277 27.1 58” 85 FEP-1748-1RA 1700 5802 480 3.5 58” 80FEP-7627-1RA 7600 25938 480 9.1 58” 85 FEP-3420-1RA 3400 11604 208 16.3 58” 85FEP-7648-1RA 7600 25938 208 47.8 58” 85 FEP-3424-1RA 3400 11604 240 14.2 58” 85FEP-7657-1RA 7600 25938 208 27.7 58” 85 FEP-3427-1RA 3400 11604 277 12.3 58” 85

FEP-3448-1RA 3400 11604 480 7.1 58” 85FEP-3457-1RA 3400 11604 600 5.7 58” 85


CabinetLength

Wt (lbs)


CabinetLength

Wt (lbs)

T-2A Series Three Phase280°C / 536°F – Class 1, Group B, C & D, Divisions 1 & 2

T-3A Series Three Phase180°C / 356°F – Class 1, Group B, C & D, Divisions 1 & 2

FEP-1820-3RA 1800 6143 208 5.0 34” 50 FEP-0820-3RA 800 2730 208 2.2 34” 50FEP-1821-3RA 1800 6143 240 4.3 34” 50 FEP-0824-3RA 800 2730 240 1.9 34” 50FEP-1848-3RA 1800 6143 480 2.2 34” 50 FEP-0848-3RA 800 2730 480 0.9 34” 50FEP-3620-3RA 3600 12286 208 10.0 34” 54 FEP-1620-3RA 1600 5460 208 4.4 34” 54FEP-3624-3RA 3600 12286 240 8.7 34” 54 FEP-1624-3RA 1600 5460 240 3.8 34” 54FEP-3648-3RA 3600 12286 480 4.3 34” 54 FEP-1648-3RA 1600 5460 480 1.9 34” 54FEP-3820-3RA 3800 12969 208 10.5 58” 80 FEP-1720-3RA 1700 5802 208 4.7 58” 80FEP-3824-3RA 3800 12969 240 9.1 58” 80 FEP-1724-3RA 1700 5802 240 4.1 58” 80FEP-3848-3RA 3800 12969 480 4.6 58” 80 FEP-1748-3RA 1700 5802 480 2.0 58” 80FEP-7620-3RA 7600 25938 208 21.1 58” 85 FEP-3420-3RA 3400 11604 208 9.4 58” 85FEP-7624-3RA 7600 25938 240 18.3 58” 85 FEP-3424-3RA 3400 11604 240 8.2 58” 85FEP-7648-3RA 7600 25938 480 9.2 58” 85 FEP-3448-3RA 3400 11604 480 4.1 58” 85

Suffix* DescriptionT1 EPETD8S single pole thermostat factory mounted to 120V-480V unitsT2 EPETD8D double pole thermostat factory mounted to 120V-480V units

C1-TD** Control section with transformer, 24V contactor, SP thermostat (40°F-90°F) and disconnect switch (all units)C1-TDP** Control section with transformer, 24V contactor, SP thermostat (40°F-90°F), disconnect switch and pilot light (all units)



Local: 972-247-8871


TPI CORPORATIONLoading Dock LightIncandescent Flex ArmCeiling Mounted

• Flexible elastomer arm moves when hit and then returns light to original position

• Ceramic socket will accept incandescent bulbs, R-40 or PAR bulbs up to 300W (bulb not included)

• On/off toggle switch on light head• UL listed

TPI CORPORATIONLoading Dock LightMotion Activated SensorQuartz Halogen Lighthead

• Energy saving sensor turns light on instantly when a person or tow motor enters the sensor field

• Safety yellow and black powder coated finish on 1-1/2” square steel tubing

• Weather resistant die cast light head with 5’ long, 3 conductor cord and plug

• 500W bulb, impact resistant lens & OSHA approved wire guard included

• 40” arm length• UL listed

TPI CORPORATIONModular Loading Dock Arms

• 1-1/2" square, 14 gauge, steel tub-ing

• 3"x5"x 3/16” mounting plate attaches with (4) 3/8" bolts

• 5' long, 18/3 SJTW conductor cord and NEMA 5-15 grounded plug

TPI CORPORATIONModular Loading Dock Lights

• 18” long, 18/3 conductor cord plugs into electri-cal junction box on arm

• On/Off switch and wire guard included with each lighthead

• Bulb included with all light-heads except DKL-INC

TPI CORPORATIONModular Loading Dock Arms & LightsMOUNTING ARMS:• 1-1/2" square, 14 gauge steel tubing• 3"x5"x 3/16” mounting plate attaches with

(4) 3/8" bolts• 5' long, 18/3 SJTW conductor cord and

NEMA 5-15 grounded plugMODULAR LIGHTS:• 18” long, 18/3 conductor cord plugs into

electrical junction box on arm• On/Off switch and wire guard included with

each lighthead• Bulb included with all lightheads except

DKL-INCMODULAR FAN:• 18" high velocity circulator, with 3 speed, 1/

8 HP, 115V, 2.2 amps, 1phase permanently lubricated, totally enclosed, PSC motor

• Modular fan plugs into electrical outlet on arm

• Chrome plated metal guards• Aluminum blades• UL listed

TPI CORPORATIONLoading Dock Light Lamp Guardfor INC, HPS & FL Lightheads

Mfg Part#

ArmLength Volt

MaxLumens

AvgBulbLife

ShipWt

(lbs) PkDKL-25-FLX 25” 120 3700 2000 7 1

Mfg Part# Volt

MaxLumens

AvgBulbLife

ShipWt

(lbs) PkDKL-40VA-SQH-A 120 11000 2000 19 1

Mfg Part# Type

ArmLength

ShipWt

(lbs) PkDKL-24-ARM Standard 24” 11 1

DKL-40VA-ARM Standard 40” 18 1DKL-60VA-ARM Standard 60” 24 1

24-LDA Heavy-Duty 24” 11 140-LDA Heavy-Duty 40” 18 160-LDA Heavy-Duty 60” 24 1

MfgPart#

LightheadType Watts

MaxLumens

AvgBulbLife

ShipWt

(lbs) PkDKL-INC Incandescent 300 3700 2000 5 1DKL-QH Quartz

Halogen500 11000 2000 6 1

DKL-HPS HP Sodium 50 4000 24000 7 1DKL-MH Metal Halide 100 9000 15000 10 1

DKL-SQH Sensor Quartz 500 11000 2000 8 1DKL-FL Fluorescent 55 3000 3000 7 1

Mfg Part#

ArmLength

ShipWt

(lbs) Pk

Heavy-Duty - IncandescentHDL-24-INC 24” 16 1HDL-40-INC 40” 24 1HDL-60-INC 60” 30 1

Heavy-Duty - Quartz HalogenHDL-24-QH 24” 17 1HDL-40-QH 40” 25 1HDL-60-QH 60” 31 1

Heavy-Duty - Incandescent + FanHDLF-24-INC 24” 36 1HDLF-40-INC 40” 44 1HDLF-60-INC 60” 50 1

Heavy-Duty - Quartz Halogen + FanHDLF-24-QH 24” 37 1HDLF-40-QH 40” 45 1HDLF-60-QH 60” 51 1

Standard-Duty - IncandescentDL-24-INC 24” 16 1DL-40-INC 40” 23 1DL-60-INC 60” 29 1

Standard-Duty - Quartz HalogenDL-24-QH 24” 17 1DL-40-QH 40” 25 1DL-60-QH 60” 31 1

Mfg Part#

ShipWt

(lbs) PkLG-1 1 1



Toll-Free: 1-800-462-4983


TPI CORPORATIONLoading Dock Light Glare Shieldfor INC, HPS & FL Lightheads

TPI CORPORATIONLoading Dock Light Polycarbonate Lensfor HPS & FL Lightheads

TPI CORPORATIONStandard-Duty Loading Dock Lights & ArmsIncandescent Light HeadFully Assembled

Lighthead and arm bolted together and shipped in one carton.

TPI CORPORATIONStandard-Duty Loading Dock Lights & ArmsQuartz Halogen Light HeadFully Assembled


TPI CORPORATIONStandard-Duty Loading Dock Lights & ArmsHigh Pressure Sodium Light HeadFully Assembled

Lighthead and arm bolted together and shipped in one car-ton.

TPI CORPORATIONStandard-Duty Loading Dock Lights & ArmsMetal Halide Light HeadFully Assembled


Mfg Part#

ShipWt

(lbs) PkGS-1 2 1

Mfg Part#

ShipWt

(lbs) PkPL-1 1 1

Mfg Part#

ArmLength

# ofArms

Wt(lbs) Pk

DKL-24-A 24” 1 10 1DKL-40VA-A 40” 2 14 1DKL-60VA-A 60” 2 17 1

MfgPart#

ArmLength

# ofArms

Wt(lbs) Pk

DKL-24-QH-A 24” 1 11 1DKL-40VA-QH-A 40” 2 15 1DKL-60VA-QH-A 60” 2 18 1

Mfg Part#

ArmLength

# ofArms

Wt(lbs) Pk

DKL-24-HPS-A 24” 1 12 1DKL-40VA-HPS-A 40” 2 16 1DKL-60VA-HPS-A 60” 2 20 1

Mfg Part#

ArmLength

# ofArms

Wt(lbs) Pk

DKL-24-MH-A 24” 1 13 1DKL-40VA-MH-A 40” 2 17 1DKL-60VA-MH-A 60” 2 21 1




Documents

TPI Fans, Heaters, and Lights - The Lawless Grouplawlessgroup.com/catalog/TPI.pdf · Toll-Free: 1-800-462-4983 3 View & Search Complete Catalog at LawlessGroup.com TPI CORPORATION