VMC-127HHIGH-SPEED & HIGH-ACCURACYVERTICAL MACHINING CENTER

1

VMC-127HVERTICAL MACHINING CENTER

Most Suitable for Needing High Speed, High Cutting Rate, High Rigidity Mold Making Industry• X & Y axes has a hardened box-way design, Z Axis with SCHNEEBERGER

roller-rail linear guide way, MRA45 rollers.• Hollow ball-screw (φ50-P16) with air cooling system for X-, Y-, and

Z- axis drive. Design with shock absorber• Rapid traverse rate 30000 mm/min, cutting feedrate 1-12000 mm/

min.• Design of C-type column with hydraulic weight-balance system

instead of using conventional chain-linked balance weight (To prevent the unexpected vibration from fast z-axis drive)

• Direct connection using a coupling for Z-axis motor.• Chip disposal system (3 screws and chip flush system

on two sides)• Design of fully support for X and Y-axes to gain

the high stability and low vibration.• Most suitable for needing high speed, high

cutting rate, high rigidity mold making industry. Without the shortcomings of high heat, high noise and high vibration when spindle speed running more than 8000rpm.

X/Y/Z : 1,200/700/600mm

(47.24"/27.56"/23.62")

24 Tools Magazine (BT-50/CAT-50)

10,000RPM Direct Driven

2

Shorten the Distance Between Work Piece and Operator • An indented foot space allows operators to get closer to the table and

workpiece.• The location of the Y-axis servomotor is at the back of the machine to shorten

the distance between the operator and table for greater work area access.

With Optional Accessories

• Safety Enhancement & Modulus Integrated Design

2 μm

Rigid Spindle Design• Heavy duty precision spindle bearings.

• A direct drive, 50-taper, 10,000RPM spindle

headstock mounts to a linear guide way Z-axis slide, enabling a rapid traverse speed of 30 meters/min (1.180in/min).

Innovative Design Enhanced By Scientific AnalysisFinite Element Analysis is used to supplement traditional machine design by strengthening areas generally overlooked by designers.

VMC-127HHIGH-RIGIDITY STRUCTURE

610mm

935mm

510mm

3

Temperature Control System for Each Ball Screw• All ball screws are air-cooled through the

center to reduce thermal growth and enable better machine accuracy.

• X and Y axis have hardened way construction.

The Z-axis uses roller-rail linear guide ways.

Superior Structure• C-Frame column with heavy duty roller-rail

guide ways on the Z-axis.

• The VMC-127H uses an hydraulically

activated nitrogen counterbalance system instead of conventional counter weights to help minimize vibration during rapid Z-axis movements.

610mm

1,400mm

1,100mm

935mm

710mm

4

VMC-127H

Calibration with Laser Interferometer is Performed and Certified by PMCAll of our machines are calibrated according to the "VDI 3441 3∂" standard. Calibration is performed for full travel length for each axis. Each measurement is taken six times to ensure the most consistent and accurate readings.

VERTICAL MACHINING CENTER

Friction Coefficient TestingAfter the exclusive "*" pattern hand scraping, technicians inspect the results using torque measurements to make sure

the ratio of contact region is over 50% and it is uniformly distributed. In addition, all contact points have a similar size, which

helps maintain even static and dynamic resistance over the entire travel range of each axis.

Ball-Bar TestingEach machine goes through telescoping ball-bar tests to check contouring accuracy and uncover any geometric errors. This testing ensures the machine structure is both square and parallel.

Hand ScrapingTo ensure consistent high quality, each slide way is hand-scraped. Each axis saddle has Turcite material on it and a special “*" design is used along with a "Z" pattern for efficient oil troughs. There is an excellent distribution of oil to all

axes, so setting time after rapid movements is eliminated, and stick-slip during cutting is minimized.

5

Linear Scales for lmproved Repeatability (Option)Linear scales on the X and Y-axes offer an exceptional positioning accuracy of up to 0.005mm over the full axes strokes. Only Heidenhain linear scales with a thermal behavior similar to that of the machine are selected so that thermal expansion can be compensated for further enhanced repeat-ability. Sealed encoders with durable aluminum housings offer improved reliability and service life.

Coolant Through Spindle (C.T.S.)(Option)Coolant through the spindle with pressure of 20-bar (150-psi) effectively reduces tool wear because of heat and the slow evacuation of metal chips.

• CTS with higher pressure is also available.

Forceful Cleaning Spray-Gun (Option)Equipped on the right front side of base, this unit along with the assistance of a high pressure coolant and air mixture helps increase table cleaning speed.

Simple Tool Length Measurement (Option)Used mostly for drilling and tapping, the Metrol system T-27R probe only measures tool length. This simple cost effective system greatly reduced tool set-up time by automatically in putting tool length values once the probe touches the tool.

6

7

Automatic Lubrication System

All AGMA machines use a pressurized central lubricating system. The PLC controlled system allows all three axes to be lubricated evenly to maintain accuracy and prolong machine life.

VERTICAL MACHINING CENTER

There Chip Auger DesignInstead of using a costly chip conveyor, the special three-chip auger system efficiently removes metal chips

produced during machining.

Electrical Cabinet All electrical components are in compliance with all safety rules and regulations.

All components inside the cabinets are clearly labeled and identified for ease of troubleshooting.

Oil Circulating Cooling System for SpindleA high efficiency spindle cooling system dissipates running induced heat generation in order to main-ainspindle accuracy and prolong spindle life.

Hinged-Belt Chip Conveyor (Option)This allows for rapid and efficient chip removal during machining in order to maintain a clean machine.

Pressurized Oil DistributorLubricating oil is evenly distributed to the sliding surfaces of the machine by using Showa brand oil distributors along with hard-plumbed, low maintenance oil lines.

24 Tools MagazineA rapid arm-type tool changer is driven with a precision cam, maintaining tool-changing accuracy of 0.01mm, which in turn will help maintain long-term spindle-clamping accuracy.

8

60

1.50"(38)

3.94

"( 1

00)

3.35

"( 8

5)

60

0

.98"

(

25)

3.35"(85)

1.38"(35)0.20 "(5)

0

.91"

( 2

3)

0.6

7"(

17)

30 45

0.28"(7)0.32"(8)

1.77""(45)

1

.49"

( 3

8)

7/24 TAPER

2.75

" (

69.

85")

M24(P=3)M24(P=3)

0

.98"

( 2

5)

1.83"(46.5)

4.01"(101.8)

0.12"(3)0.39"(10)

1.0

1"(2

5.7)

3.62

"( 9

1.85

)

3.88

"( 9

8.43

)

60

2.75

" (

69.

85")

0.39"(10)

1.83"(46.5) 0.13"(3.18)

4"(101.6)

1

.03"

( 2

6.19)

1

.38"

( 3

5.05

)

0.28"(7)0.32"(8)

1.77""(45)

3.35"(85)

1.38"(35)

0.91

"(

23)

0.6

7"(

17)

1.0

3" (

26.19

)

1

.49"

( 3

8)

0.20 "(5)

1"- 8UNC-2A

30 45

7/24 TAPER1"-8UN-2B

60

0.75"(19)

BT-50

CAT-50

9

mmin

a

70027.55

b

120047.24

c

140055.11

d

125*54.92*5

e

42.51.67

f

71027.95

ef

bc

40.94"(1040)

141.73"(3600)

76.7

7"(1

950)

129.

92"(3

300)

54.7

2"(1

390)

23.6

2"(6

00)

7.87

"(2

00)

13"(3

3)0.

47"(1

2)

124.41"(3160)138.97"(3530)

137.

79"(3

500)

121.

65"(3

090)36.81"(935)

1.8"(30)

0.7"(18)

161.81"(4110)

da

AGMA

VERTICAL MACHINING CENTER

10

Model VMC-127HSpindleSpindle Taper NO.50

Transmission Direct Type

Spindle Speed 10,000 r.p.m.

Table

Table Size 1,400mm x 710mm (55.12" x 27.95")

T-Slot Size 18mm x 6 x 125mm (0.71" x 6 x 4.92")

Work Area 1,200mm x 700mm (47.24" x 27.56")

Max. Table Load 1,200kgs (2,640 lbs)

Travel & Feedrate

X Axis 1,200mm (47.24")

Y Axis 700mm (27.56")

Z Axis 600mm (23.62")Distance from Spindle Nose to Table 200-800mm (7.84" - 31.50")

Distance from Spindle Center to Column Ways 935mm (36.81")

Rapid Traverse X, Y, Z =30,000 mm/min (1.180inch/min)

Cutting Feedrate X, Y, Z= 1~12,000mm /min

ATC

Tool Shank BT/CAT 50

Pull Stud MAS P50T-1 (45°)

Magazine Capacity 24 ToolsMax. Tool Diameter (with Adjacent Pocket Empty) ø250mm (9.84")

Max. Tool Diameter (Full Storage) ø125mm (4.92")

Max. Tool Length 300mm (11.81")

Max. Tool Weight 15kgs (33 lbs)

ATC Type Cam Driven Arm Type

Motor

Spindle (Cont./30min.) 15/18.5Kw (30min) (20/25 HP)

X/Y/Z Axes (Fanuc/Mitsubishi) 3.8Kw/3.5Kw (5.09 HP/4.69 HP)

Lubrication Pump 0.025Kw (0.033 HP)

Coolant Pump 0.49Kw (0.66 HP)

Machine Height 3,500mm (137.79")

Floor Space 4,110mm x 3,530mm (161.81"x138.98")

Machine Weight 12,000kgs (26,400 lbs)

Control Fanuc 0iMD 8.4"

•Specification is subject to change without further notice.

Standard Accessories : 1. Fanuc 0iMD 8.4"

2. Heat Exchanger for Electrical

3. Three-Color Indicator Light

4. Quartz Work Lamp

5. RS-232 Interface

6. 24 Tools Arm Type (ATC)

7. 10,000 RPM Direct Driven Spindle

8. Oil Circulating Cooling System for Spindle

9. Spindle Air Blast

10. Automatic Lubrication System

11. Fully Enclosed Splash Guard

12. Rigid Tapping

13. Automatic Power Off

14. Temperature Control System for Each Ball Screw

15. Tool Box W/Leveling Bolts & Pads

16. Operation Manual & Maintenance Manual

17. X+Y Axis Screw Type Chip Auger (3 pcs)

18. Transformer (Exclude India, USA and Canada)

19. CE/CSA Electrical System (For European/Canada Country Only)

Optional Accessories : 1. Fanuc 31iMB Controller

2. 32 Tools Arm Type (ATC)

3. 12,000 RPM Direct Driven Spindle

4. Chip Conveyor

5. Coolant Through Tool

6. Heidenhain Optical Linear Scales for all axes

7. Coolant Through Spindle (20/70 Bars-Closed Hole) A Type

8. Automatic Tool Length Measurement System

9. Rotary Table (4th Axis)

10. Electrical Box Air Conditioner Device

VERTICAL MACHINING CENTER

13

04

12

02

T

EL

: 04

-24

73

33

26

Distributor :AGMACHINE TECHNO CO., LTD.No.7, Ln. 34, Jhuangcian Rd., Shengang Dist . ,

Taichung City 42951, Taiwan(R.O.C.)

TEL:+886-4-25612868

FAX:+886-4-25610409 & 25613010

E-mail : mk21@agma.com.tw

http://www.agma.com.tw