Zoeller 295

Embed Size (px)

Citation preview

  • 8/12/2019 Zoeller 295

    1/2

    SECTION: 2.30.050

    FM0450

    0308

    Supersede

    0706

    COMPARE THESE FEATURES Non-clogging vortex impeller design. Bronze class

    84-8-0-4.

    Durable cast construction. Cast iron switch case, base,

    motor and pump housing. No sheet metal parts to rust

    or corrode. All cast iron class 25-30 25000# tensile

    strength.

    Stainless steel screws, bolts, float rod, handle, guard,

    arm and seal assembly.

    20 ft. UL Listed 3-wire neoprene cord and plug. Extra

    cord lengths available in 25-35-50 foot lengths only.

    3 phase models available (292, 115V/1Ph only).

    Motor - 60 Hz, 3450 RPM, oil-filled, hermetically

    sealed, automatic reset, thermal overload protected (1

    Ph only).

    Maximum temperature for sewage or dewatering

    130F (54C), 120F (49C) for WD295. If over 130F,

    consult Factory.

    Shaft Seal - Stainless steel carbon & ceramic rotary.

    Corrosion resistant powder coated epoxy finish.

    Upper sleeve bearing and lower ball bearing running in

    bath of oil.

    Square Ring & Gasket - Neoprene.

    All models pass 2" spherical solids.

    Major width 127

    /8" Height 189

    /16" (Single sealpumps).

    Automatic units available with float operated,

    submersible (NEMA 6) 2-pole mechanical switch. On

    point 143/4" - Off point 5".

    Specify 2" or 3" NPT female flanged vertical discharge.

    100% computerized testing.

    MODELS 4292-4293-4294-4295DOUBLE SEAL PUMPS (Nonauto only)

    Gives motor extra protection from seal leaks.

    Improved bearing lubrication.

    Helps eliminate seal and bearing damage from dry

    runs.

    Major width 12 7/8". Height 20 7/16".

    Note: The sizing of effluent systems normally requires

    variable level float(s) controls and properly sized

    basins to achieve required pumping cycles or dosing

    timers with nonautomatic pumps.

    Product information presentedhere reflects conditions at timeof publication. Consult factoryregarding discrepancies orinconsistencies. MAIL TO: P.O. BOX 16347 Louisville, KY 40256-0347

    SHIP TO: 3649 Cane Run Road Louisville, KY 40211-1961

    (502) 778-2731 1 (800) 928-PUMP FAX (502) 774-3624

    visit our web site:

    www.zoeller.com

    Copyright 2008 Zoeller Co. All rights reserved.

    292 - 293 - 294 - 295 Single Seal Series4292 - 4293 - 4294 - 4295 Double Seal Series

    (For Pump Prefix Identification see News & Views 0052)

    HIGH HEAD

    WASTE-MATESUBMERSIBLE

    SEWAGEOR DEWATERING PUMP

    Double

    Seal

    Pump

    Nonautomatic

    models for

    variable level

    systems

    Automatic units

    available in

    single phase 292,

    293, 294 & 295

    series

    WD295 controlled

    by variable level

    float switch

    *See back page for UL & CSA listings

    Tested to UL

    Standard UL778

    R *

    *

    R

    Certified to CSA

    Standard C22.2 No.108

  • 8/12/2019 Zoeller 295

    2/2

    SK1415

    SELECTION GUIDE

    1. Integral float operated mechanical switch, no external control

    required.

    2. For automatic use single piggyback variable level float switch or

    double piggyback variable level float switch. Refer to FM0477.

    3. See FM1228 for correct model of simplex control panel.

    4. See FM0712 for correct model of duplex control panel.

    Single Seal Automatic Design

    Weight 86-89 lbs.

    * No Molded Plug.

    ** Single piggyback switch included.

    (1) UL Listed unit available with 20 Amp plug.

    (2) CSA Approval with 20 Amp plug.

    RESERVE POWERED DESIGNFor unusual conditions a reserve safety factor is engineered into the design of every Zoeller pump.

    For information on additional Zoeller products refer to catalog on Explosion

    Proof Models, FM1702; Simplex controls, FM1596; Piggyback Variable Level

    Float Switches, FM0477; Electrical Alternator, FM0486; Mechanical Alternator,FM0495; Sump/Sewage Basins, FM0487; Alarm Systems, FM0732; Disconnect/Rail

    Systems, FM0787; and Junction Boxes FM1597.

    All installation of controls, protection devices and wiring should be done by a quali fied

    licensed electrician. All electrical and safety codes should be followed including the

    most recent National Electrical Code (NEC) and the Occupational Safety and Health

    Act (OSHA).

    Copyright 2008 Zoeller Co. All rights reserved.

    292 MODELS 4292 MODELS Standard all models - 20 ft. cord - HP Control Selection Listings

    Single Seal Double Seal Volts - Ph Mode Amps Simplex Duplex CSA UL

    M292 --- 115 1 Auto 15.0 1 --- Y Y N292 N4292 115 1 Non 15.0 2 or 3 2 or 4 Y Y(1)

    293 MODELS 4293 MODELS Standard all models - 20 ft. cord - 1 HP Control Selection Listings

    Single Seal Double Seal Volts - Ph Mode Amps Simplex Duplex CSA UL

    D293 --- 230 1 Auto 10.2 1 --- Y Y

    E293 E4293 230 1 Non 10.2 2 or 3 4 Y Y

    * H293 --- 200 1 Auto 12.0 1 --- Y N

    * I 293 * I 4293 200 1 Non 12.0 2 or 3 4 Y N

    * F293 * F4293 230 3 Non 7.6 3 4 Y Y

    * J293 * J4293 200 3 Non 8.2 3 4 Y Y

    * G293 * G4293 460 3 Non 4.0 3 4 Y Y

    * BA293 --- 575 3 Non 3.3 3 4 N N

    294 MODELS 4294 MODELS Standard all models - 20 ft. cord - 1 HP Control Selection Listings

    Single Seal Double Seal Volts - Ph Mode Amps Simplex Duplex CSA UL

    D294 --- 230 1 Auto 13.7 1 --- Y Y(1)

    E294 E4294 230 1 Non 13.7 2 or 3 4 Y Y(1)

    * H294 --- 200 1 Auto 17.8 1 --- N N

    * I 294 * I 4294 200 1 Non 17.8 2 or 3 4 N N

    * F294 * F4294 230 3 Non 9.5 3 4 Y Y

    * J294 * J4294 200 3 Non 10.8 3 4 Y Y

    * G294 * G4294 460 3 Non 4.8 3 4 Y Y

    * BA294 --- 575 3 Non 3.8 3 4 Y N

    295 MODELS 4295 MODELS Standard all models - 20 ft. cord - 2 HP Control Selection Listings

    Single Seal Double Seal Volts - Ph Mode Amps Simplex Duplex CSA UL

    D295 --- 230 1 Auto 17.1 1 --- Y(2) Y

    E295 E4295 230 1 Non 17.1 2 or 3 4 Y

    (2)

    Y WD295 --- 230 1 Auto 17.1 ** 4 N N

    * H295 --- 200 1 Auto 20.5 1 --- N N

    * I 295 * I 4295 200 1 Non 20.5 2 or 3 4 N N

    * F295 * F4295 230 3 Non 12.2 3 4 Y Y

    * J295 * J4295 200 3 Non 14.3 3 4 Y Y

    * G295 * G4295 460 3 Non 6.1 3 4 Y Y

    * BA295 --- 575 3 Non 4.9 3 4 Y N

    PUMP PERFORMANCE CURVE

    MODEL 292/4292/293/4293/294/4294/295/4295

    0 80 160 240 320 400 480

    220140130120110100908070605040302010

    0

    2

    4

    6

    8

    10

    12

    14

    16

    18

    20

    80

    65

    60

    55

    50

    45

    40

    35

    30

    25

    20

    15

    10

    5

    LITERS

    GALLONS

    FEET

    METERS

    TOTALD

    YNAMIC

    HEAD

    FLOW PER MINUTE

    1 50 1 60 1 70 1 80 1 90 2 00 2 10

    560 640 720 800

    70

    22

    292/4292

    293/4293

    294/4294

    295/4295

    75

    24

    Model 293 should not

    be subjected to less

    than 15' TDH.

    009919A

    Double Seal Design / Weight 92-95 lbs.

    294/4294

    G al . L it ers

    196 742

    181 685

    165 625

    150 568

    136 515

    121 458

    94 356

    58 220

    13 49

    -- --

    62 ft.(18.9m)

    292/4292 293/4293

    199 753

    115

    23

    89

    59

    154

    140

    184

    168

    435

    87

    337

    223

    583

    530

    696

    636

    295/4295

    Gal.

    214 810

    Liters

    75 ft.(22.9m)

    MODEL

    Feet Meters Gal. Liters Gal . Li ters

    5 1.5 530140 -- --

    10 3.0 469124 -- --

    4.6 409108 118 44715

    6.1 34491 108 40920

    7.6 28475 96 36325

    9.1 21256 82 31030

    12.2 3810 48 18240

    15.2 ---- -- --50

    18.3 ---- -- --60

    21.3 ---- -- --70

    Shut-of f Head: 42 f t. (12.8m) 50 f t. (15.2m)

    18 9/16

    6

    4 1/8 8 3/4

    6 1/2

    4 1/8

    6 11/32

    2" NPT

    OR3" NPT

    AVAILABLE

    IN A FLANGE

    SK863

    6

    4 1/8 8 3/4

    6 1/2

    4 1/8

    20 7/16

    4 1/8

    2" NPT

    OR

    3" NPT

    AVAILABLE IN A FLANGE