5/28/2018 Belajar Structural Detailing
1/41
AutoCADStructuralDetailing2011
GettingStartedwithAutoCAD
StructuralDetailing,
Reinforcementmodule
5/28/2018 Belajar Structural Detailing
2/41
2010 Autodesk, Inc. All Rights Reserved. Except as otherwise permitted by Autodesk, Inc., thispublication, or parts thereof, may not be reproduced in any form, by any method, for any purpose.
Certain materials included in this publication are reprinted with the permission of the copyrightholder.
DisclaimerTHIS PUBLICATION AND THE INFORMATION CONTAINED HEREIN IS MADE AVAILABLEBY AUTODESK, INC. AS IS. AUTODESK, INC. DISCLAIMS ALL WARRANTIES, EITHEREXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO ANY IMPLIED WARRANTIESOF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE REGARDING THESEMATERIALS.
TrademarksThe following are registered trademarks of Autodesk, Inc., in the USA and/or other countries:Autodesk Robot Structural Analysis, Autodesk Concrete Building Structures, Spreadsheet Calculator, ATC, AutoCAD,Autodesk, Autodesk Inventor, Autodesk (logo), Buzzsaw,Design Web Format, DWF, ViewCube, SteeringWheels, and Autodesk Revit.All other brand names, product names or trademarks belong to their respective holders.
Third Party Software Program CreditsACIS Copyright 1989-2001 Spatial Corp. Portions Copyright 2002 Autodesk, Inc.Copyright 1997 Microsoft Corporation. All rights reserved.
International CorrectSpell Spelling Correction System 1995 by Lernout & Hauspie SpeechProducts, N.V. All rights reserved.InstallShield 3.0. Copyright 1997 InstallShield Software Corporation. All rights reserved.PANTONE and other Pantone, Inc. trademarks are the property of Pantone, Inc. Pantone, Inc.,2002.Portions Copyright 1991-1996 Arthur D. Applegate. All rights reserved.Portions relating to JPEG Copyright 1991-1998 Thomas G. Lane. A ll rights reserved. Portions ofthis software are based on the work of the Independent JPEG Group.Portions relating to TIFF Copyright 1997-1998 Sam Leffler. Copyright 1991-1997 SiliconGraphics, Inc. All rights reserved.
Government UseUse, duplication, or disclosure by the U.S. Government is subject to restrictions as set forth inFAR 12.212 (Commercial Computer Software-Restricted Rights) and DFAR 227.7202 (Rights inTechnical Data and Computer Software), as applicable.
5/28/2018 Belajar Structural Detailing
3/41
Contents
GettingStartedGuide................................................................................................................................... 1
GettingStarted
..........................................................................................................................................
1
ExploringtheUserInterface...................................................................................................................... 1
ObjectInspector........................................................................................................................................ 3
ProgramPreferences................................................................................................................................. 5
TypesofReinforcement............................................................................................................................ 6
RulesforPositioningaReinforcingBarinaDrawing................................................................................ 6
DescriptionsofReinforcement.................................................................................................................. 7
Workflow................................................................................................................................................... 7
CreatingaReinforcedConcreteStructure................................................................................................ 8
CreatingaTemplate.............................................................................................................................. 8
DefiningFormworkofaBeam............................................................................................................. 12
AddingAxes......................................................................................................................................... 14
AddingaStirrupintheCrossSection.................................................................................................. 15
AddingaStirrupintheElevationView................................................................................................ 17
DefiningMainBars.............................................................................................................................. 20
CreatingCross
sections
.......................................................................................................................
24
CreatingaColumnandaSpreadFooting............................................................................................ 30
AddingMaterialTakeoffs.................................................................................................................... 34
DefinitionofViews.............................................................................................................................. 36
CreatingSheetsandAddingViews...................................................................................................... 37
5/28/2018 Belajar Structural Detailing
4/41
GettingStartedGuide
ThankyouforchoosingAutoCADStructuralDetailing.TheReinforcementmoduleisfor
automatedreinforcement
definition
and
the
generation
of
shop
drawings
for
all
types
of
structuralconcretemembers.Theexercisesinthisguidegiveyouastartingpointfor
preparationofyourownprojects.
GettingStarted
Beforebeginningtheexercises,youneedtoinstallandregisterthesoftware.
AutoCADStructuralDetailingsoftwarecomeswiththeAutoCADRevitStructure
Suite.This
software
is
available
for
32
bit
and
64
bit
Windows
systems.
ExploringtheUserInterface
OpenAutoCADStructuralDetailing,Reinforcementmodule,andtakeaminuteto
viewthedifferentareasoftheinterface.
Ribbon
At the topof the interface is the standardMicrosoftWindowselement ribbon.
The ribbon isanelementof theuser interfacewhich replaces the traditionalmenu
and toolbars and allows easymanaging and adjusting theworkspace. The ribbon
consistsof severalpanels,groupedon tabs thatarenamedby taskor subject.The
ribbonpanelsincludemanyAutoCADStructuralDetailingcommandsthathavebeen
ontoolbarsandindialogssofar,suchasicons,dropdownlists,sliders,textfieldsand
otherelementscharacteristicofagiventab.
NOTEItispossibletoswitchbetweenworkspaces(suchastheclassicworkspacewithoutthe
ribbon).Todoitfollowoneofthegivenmethods:
1ClickManageCustomization (UserInterface)intheCustomizeUserInterfacedialogboxselecttheCustomizetabandinASD/WorkspacesselectASD
ReinforcementClassicrightclickselectSetcurrentfromthecontextmenu
clickApply
2Click (atthebottomrightcornerofthescreen)andselectASDReinforcementClassic.
1
5/28/2018 Belajar Structural Detailing
5/41
ObjectInspector
Inspectorletsyoumanageelements(objects)includedinaprojectthatwascreatedin
AutoCADStructuralDetailing.
Layout/ModelTabBar
AtthebottomofthedrawingareaisthestandardAutoCADModel/LayoutTabBar.
Thereare2additionaltabsdefinedEditionLayoutandTemplatesLayout.Onthe
EditionLayouttab,youcanmodifythedrawings(documents)generatedforthe
structureelementsorgroupofelements.TheTemplatesLayouttabdisplaysthe
printouttemplatesdefinedintheproject.
Ribbon
Model/DrawingAreaModel/LayoutTabBarObjectInspector
2
5/28/2018 Belajar Structural Detailing
6/41
ObjectInspector
UsingtheInspector,youhavequickaccesstoprojectelementsfromeverystageof
work,whichhelpsyoumanageyourproject. Bydefault,theObjectInspectordialog
displayson
the
left
side
of
the
interface,
beside
the
drawing
area.
You
can
adjust
the
widthofthedialogtoleaveasmuchspaceaspossiblefordrawingthegraphicmodel.
OntheModeltabisalistofmodelelements(levels,groups,andelementsthatbelong
tothelevelsandgroups)thatdescribethedivisionofreinforcingbarsintostructural
elements(beams,columns,spreadfootings,andsoon).
ThePositionstabdisplaysalistofdefinedviewsthatcontainthename,scale,and
printoutlayoutnamefortheview.
3
5/28/2018 Belajar Structural Detailing
7/41
ThePrintoutstabletsyoumanageprintoutsinAutoCADStructuralDetailing.It
displaysthelistofallprintoutsandtheassociatedviewsdefinedintheAutoCAD
StructuralDetailingproject.Theprintoutlistincludesallprintouts,eventhosethatdo
notcontainviews.
UsetheASDCentertabtocopysettingsandstylesbetweenprojects.
4
5/28/2018 Belajar Structural Detailing
8/41
ProgramPreferences
Preferences
ThePreferences
are
located
in
AutoCADs
Options
dialog.
The
Structural
Detailing
tab
letsyouselectthedefaultstarttemplateandworkspacenamefortheReinforcement
module.Thesoftwareprovidesmanytemplatesthataredefinedforspecific
countries.
Jobpreferences
Thesepreferencesarerelatedtoaparticulartemplateandproject.Afteryouhave
startedworkingonaproject,itisnotpossibletochangeworkunits.Somesettings
(suchasdesigncodesanddatabases)arespecifiedonlyatthebeginningofthe
project,beforeyouaddelementsintomodelspace.
5
5/28/2018 Belajar Structural Detailing
9/41
TypesofReinforcement
Usingthereinforcementmodule,youcancreaterebarorwirefabricforstructural
elementsofeverytypeandshape(frombeamstoadvanced,complicatedelements).
Thereare3waystodefinereinforcementofstructuralelements:
Manually Automatically,basedonmacrosforthegenerationofreinforcementandformworkoftypicalstructures.MacrosinAutoCADStructuralDetailinglet
yougeneratecompleteconcretereinforcementdrawings,togetherwithrebar
descriptionsandmaterialtakeoffs.
Usingdatafromexternalsoftware,byimportingandexportingfromAutodeskRobotStructuralAnalysisProfessionalsoftware,andbyexporting
reinforcementdatafromRevitStructuresoftware.
RulesforPositioningaReinforcingBarinaDrawing
Thesoftwaredeterminesthepositionofareinforcingbarinadrawingdependingon
thedirectioninwhichpointsaredefined.Theorientationofthereinforcingbaris
determinedbytheorderofthepointsinaclockwisedirection,inrelationtothe
externalpartofanobject.
6
5/28/2018 Belajar Structural Detailing
10/41
DescriptionsofReinforcement
Afterreinforcementisdefined(barshape,reinforcementdistribution,wirefabric
distribution,andsoon),thesoftwareautomaticallyrunsanoptionthatsuggestsa
descriptionappropriate
for
the
reinforcement
type.
The
resulting
dialog
depends
on
thetypeofselectedreinforcementdescription.
EverytypeofdescriptionhastheActiveoption.Iftheoptionison,thenthe
reinforcementisdescribedandiscountedinthereinforcementtable.Whenthesame
reinforcementisdescribedtwice,theoptionshouldbeofftopreventdoublingthe
numberofreinforcingbarscalculatedwhenpreparingabartable.
Workflow
Thecreationofeverycompleteprojectisbasedon3stages:
Modeling youworkontheModeltab(modelspace)todefineformworks,reinforcement,andmaterialtakeoffs.
Viewsyouworkinmodelspacetodefineeachviewasasingleelementwithitsownscale.
PrintoutsyouworkinLayoutspacetopreparethefinalshopdrawings.Inthisstage,youworkwithviewsthatwerecreatedearlier.
Modeling
Views
Shopdrawings
7
5/28/2018 Belajar Structural Detailing
11/41
CreatingaReinforcedConcreteStructure
Inthislesson,youwillcreateasimplereinforcedframeandmaterialtakeoffs.Youwill
alsocreateafinalshopdrawing.
CreatingaTemplate
InordertostartworkinginAutoCADStructuralDetailing,youneedtoselecta
template.Thetemplatefilecontainsinitial,predefinedsettingsoftheworking
parameters.Inthisexercise,youwillcreateatemplate.
1 Click New.2 IntheSelecttemplatedialog,selectRBCR044.dwt,andclickOpen.3 DefineanewBartablestyle:
ClickASD ReinforcementSettingsStyles reinforcement
tables.Alternatively(forASDReinforcementClassicworkspace),
clickReinforcementmenuReinforcementtableStyles
Reinforcementtables.
IntheReinforcementtables stylemanager,forTable,selectMAIN
bars,andthenclickNew.
OntheTabletaboftheDefinitionofnewreinforcementtablestyle
dialog,selectMAIN,andthenclearRevisionandselectBarsymbol.
8
5/28/2018 Belajar Structural Detailing
12/41
Click .
SelectLENGTHS,andthenselectTotal(bar).
ForUnits,selectm(meter),andspecifytheaccuracyas2decimal
places(0.00).
VerifythatBarisselected,andspecifythesamesettings.
Click .
OntheSortinganddetailedoptionstab,underDescriptionofbar
symbol,selectSymbol:A,B,C.
Onthe
Options
tab,
select
Automatically
adjust
row
height.
ForListofstyles,enterMyBarTableStyleasthenameofthenew
style.
9
5/28/2018 Belajar Structural Detailing
13/41
ClickOK.
IntheReinforcementtables stylemanagerdialog,forTablestyle,
selectMyBarTableStyle,andthenclickDefault.
Click
OK.
4 ChangeJobpreferences:ClickASD ReinforcementSettings (Jobpreferences).
Alternatively,clickReinforcementmenuJobpreferences.
IntheleftpaneoftheJobpreferencesdialog,selectBarsDisplay.
UnderBarshape,forEndofstraightbars(withouthooks),selectthe
secondoption.
Intheleftpane,selectCodes/Materials.
UnderReinforcingbars,forDatabase,click andselectbar_BS
8666_2000database.
UnderReinforcingbars,forSteelgradeRandT,changetheSymbol
to.
ClickOK.
10
5/28/2018 Belajar Structural Detailing
14/41
5 Defineanaxisstyle:ClickASD ReinforcementSettingsGraphicelementsstyles.
Alternatively,clickReinforcementmenuGraphicelements
Styles graphicelements.
IntheStylesofsymbolsdialog,forSymbol,selectAxis,andthenclick
New.
IntheAxisdialog,underAxis,forColor,selectMagenta.
ForStylename,enterMyAxisStyle,andthenclickAdd.
IntheStylesofsymbolsdialog,forSymbolstyles,select
MyAxisStyle,andthenclickDefault.
ClickClose.
11
5/28/2018 Belajar Structural Detailing
15/41
6 Savethetemplate:
Click Saveas.
For
File
name,
enter
MyTemplate.dwt,
and
click
Save.
IntheTemplateOptionsdialog,clickOK.
7 Setyourtemplateasadefault:ClickASD ReinforcementSettings (Preferences).
Alternatively,clickReinforcementmenuPreferences.
OntheStructuralDetailingtaboftheOptionsdialog,for
Reinforcement,clickSearch.
IntheOpendialog, selectMyTemplate.dwt,andclickOpen.
IntheOptionsdialog,clickOK.
Closetheprogram.
8 Proceedtothenextexercise,DefiningFormworkofaBeam.
DefiningFormwork
of
aBeam
Beforeyoubegindefiningreinforcementforabeam,youshoulddefineitsformwork.
TheformworkintheReinforcementmodulecanbecreatedusingMacrosorusing
AutoCADoptions.Inthisexercise,youaddtheformworkofthebeamintomodel
space.
1 StarttheReinforcementmoduleofAutoCADStructuralDetailing:
ClickASD
Start
(Reinforcement).
2 ClickASD StructureElementsStructureelements formwork(Beam).Alternatively,clickReinforcementmenuFormworksBeam.
3 IntheBeamdialog,forGeometrytab,specifyparametersofthebeamsformworkasshown.
12
5/28/2018 Belajar Structural Detailing
16/41
4 IntheBeamdialog,forSectionstab,specifyparametersofthebeamsformworkasshown.
5 ClickOK.6 Inthedrawingarea,clicktospecifyaninsertionpoint.7 RemoveaxesatthebeamssupportbyusingAutoCADEraseoption.8 Modifyheightofbeamsupportto500mmbyusingAutoCADStretchoptionasshowninthedrawingbelow.
13
5/28/2018 Belajar Structural Detailing
17/41
9 Proceedtothenextexercise,AddingAxes.
AddingAxes
Inthisexercise,youwilladd2axestothebeamformwork.
1 ClickASD ReinforcementGraphicelements (Insertaxis).Alternatively,clickReinforcementmenuGraphicelementsInsert
axis.
2 Onthecommandline,changetheaxisnumberto1.3 Insertthefirstaxisinthemiddleoftheleftbeamsupport:
Selectfirstpoint.
Selectsecondpoint.
4 Usingthesamemethod,addaxis2tothemiddleoftherightsupportbeam.
5 Proceedtothenextexercise,AddingaStirrupintheCrossSection.
14
5/28/2018 Belajar Structural Detailing
18/41
Adding
a
Stirrup
in
the
Cross
Section
Inthisexercise,youlldefinestirrupsinthecrosssectionAAofbeamformwork.You
willdefinerebarshapeswiththeirdescriptions.
1 AddanauxiliarypointintheformworkcrosssectionAA:ClickHomeDrawMultiplePoints.Alternatively,clickDraw
menuPointMultiplePoint.
Clicktheupperrightcornerofthecrosssectionasthefirstpoint.
Onthecommandline,type@114,0,andthenpressEnter.
PressEsc.
2 Defineastirrup:ClickASD ReinforcementReinforcementdefinition
Reinforcementcrosssection.Alternatively,clickReinforcement
menuReinforcement crosssection.
IntheReinforcementcrosssectiondialog,click .
Specifyrebarparametersasshown.
15
5/28/2018 Belajar Structural Detailing
19/41
ClickShapeparameters.
IntheReinforcingbarparametersdialog,specifystirrupparameters
asshown.
ClickOK.
IntheReinforcementcrosssectiondialog,selectamodeof
graphicalreinforcement
definition,
and
then
click
(Insert).
Inthedrawingarea,selecttheauxiliarypointyoudefined,choose
theproperorientationforthestirrup,andthenpressEnter.
IntheReinforcementdescriptiondialog,acceptthedefault
parameters,andclickOK.
Insertdescriptionofthestirrupbyselectingpointsinthemodel
area.
16
5/28/2018 Belajar Structural Detailing
20/41
3 Mirrorthestirrup:SelectthestirrupwithdescriptionandclickHomeModify
(Mirror). Alternatively,clickModifymenuMirror.
Clickaboveandbelowthecrosssectionatthemidpointtospecify
thefirst
and
second
points
of
the
mirror
line.
4 Proceedtothenextexercise,AddingaStirrupintheElevationView.
AddingaStirrupintheElevationView
Inthisexercise,youlldefinestirrupsintheelevationviewofbeamformwork.Youwill
definerebardistributionwiththeirdescriptions.
1 ClickASD ReinforcementReinforcementdefinition(Reinforcementdistribution).Alternatively,click Reinforcementmenu
Reinforcementdistribution.
2 Inthedrawingarea,selectbothstirrupsinthecrosssection,andpressEnter.
17
5/28/2018 Belajar Structural Detailing
21/41
3 IntheReinforcementdetailingdialog:ForDistributionTYPE,click (Linear).
ForDistribution
METHOD,
click
(Module).
ForViewingDIRECTION,click (projectiontoYaxis).
ClickOK.
4 Definedistributionintheelevationview:Inthedrawingarea,clickpoint1tospecifythedistributionstart
point.
Clickpoint2tospecifythedistributionendpoint.
Todefinethepositionofthefirstrebar,enter20onthecommand
line.
18
5/28/2018 Belajar Structural Detailing
22/41
Todefinestirrupspacing,type7*170,where7isthenumberofstirrupsand170isthespacing.
Definethesecondstirrupspacingas5*250.
Right
click,
and
click
Mirror.
PressEnter.
NOTEAfterreinforcementisdefined(barshape,reinforcement
distribution,wirefabricdistribution,andsoon),thesoftware
automaticallyrunsanoptionthatsuggestsadescriptionappropriatefor
thereinforcementtype.Theresultingdialogdependsonthetypeof
selectedreinforcementdescription.
IntheReinforcementdescriptiondialog,acceptthedefault
parameters,andclickOK.
Inthemodelspace,selectthepointtodefinethelocationofthe
distributionline.
Clicktospecifythedescriptionlocation.
5 Modifythedefineddistribution:Selectthedistributionofstirrups,rightclick,andclickModify.
IntheModificationofreinforcementdistributiondialog,clickDelete,
andclickthestirrupinthemiddleofbeam.Thepropernumberof
stirrupsshouldbe2x25.
PressEsc,andthenclickOK.
19
5/28/2018 Belajar Structural Detailing
23/41
7 Proceedtothenextexercise,DefiningMainBars.
DefiningMain
Bars
Inthisexercise,youlldefinelongitudinalreinforcementofbeamintheelevation
view.
1 Definethefirstlongitudinalrebarinelevationview(rebarnumber2):ClickASD ReinforcementReinforcementdefinition
(Reinforcementelevation).Alternatively,clickReinforcement
menu
Reinforcement
elevation.
IntheReinforcement elevationdialog,click .
Specifytherebarparametersasshown.
Click (Points).
20
5/28/2018 Belajar Structural Detailing
24/41
Inthedrawingarea,clickpoint1tospecifythefirstbarattachmentpoint.
Clickpoint2tospecifythesecondbarattachmentpoint.
IntheReinforcementdescriptiondialog,clickOKtoadddescription
tothe
rebar
by
clicking
points
in
the
model
area.
2 Usingthesamemethod,defineanotherrebar(number3)withadiameterof16mm,andspecifyitslocationasshown.
21
5/28/2018 Belajar Structural Detailing
25/41
IntheReinforcementdescriptiondialog,clickOK.
3 Definethelastrebarinelevationview:
ClickASD
Reinforcement
Reinforcement
definition
(Reinforcementelevation).Alternatively,clickReinforcement
menuReinforcementelevation.IntheReinforcement
elevationdialog,specifytherebarparametersasshown.
Click (Points).
Inthedrawingarea,clickpoint1asshowntospecifythebar
attachmentlocation.
22
5/28/2018 Belajar Structural Detailing
26/41
Rightclick,andclickMirror.
Rightclick,andclickSide.
Clickpoints2and3tospecifyadditionalcharacteristicpoints.
NOTEYou
can
add
auxiliary
characteristic
points
to
formwork
using
the
AutoCADDrawoption.
Onthecommandline,typeStochangethesideofacover.
Clickpoints4and5tospecifyadditionalcharacteristicpoints.
IntheReinforcementdescriptiondialog,clickOK.
Descriptionisaddedtotherebar.
NOTEWhenyoudefinebarsfromthedatabase,youselectoneofthem
fromtheavailableshapelist.Youthendefinesuccessivebarsegmentsby
selectingthenextbarscharacteristicpointsintheschematicdrawing(or
bytypingdimensionsofindividualsegments).
4 Proceedtothenextexercise,CreatingCrosssections.
23
5/28/2018 Belajar Structural Detailing
27/41
CreatingCrosssections
Afteryouhavefinishedplacingbeamrebarintheelevationviewandhavedefined
theirshapes,youcalculatethenumberoflongitudinal(main)rebarsinthebeam.
Inthisexercise,youllcreate3crosssectionsincharacteristicpointsofthebeam.
1 ModifyexistingcrosssectionAA:ClickASD ReinforcementReinforcementdefinition
(Reinforcementpoint).Alternatively,clickReinforcementmenu
Reinforcement point.
Inthedrawingarea,selectrebarnumber3(oritsdescription).
IntheReinforcementpointdialog,click .
UnderDistributionparameters,selectEnd,andthenclick
(Segment).
Inthedrawingarea,selectthebottomsegmentsofeachstirrup,
rightclick,andthenpressEnter.
IntheReinforcement pointdialog,clickOK.
IntheReinforcementdescriptiondialog,specifytheparametersas
shown.
24
5/28/2018 Belajar Structural Detailing
28/41
ClickOK.
Inthedrawingarea,selectpointtodefinethelocationofthe
distributionline.
Clicktospecifythelocationofthedescription.
You
have
defined
rebar
number
3.
ClickASD ReinforcementReinforcementdefinition
(Reinforcementpoint). Alternatively,clickReinforcementmenu
Reinforcement point.
Inthedrawingarea,selectrebarnumber2.
IntheReinforcementpointdialog,click .
UnderDistributionparameters,selectBends,andclearEnd.
Click (Segment).
Inthedrawingarea,selectthetopsegmentsofeachstirrup,and
thenpressEnter.
IntheReinforcement pointdialog,clickOK.
25
5/28/2018 Belajar Structural Detailing
29/41
IntheReinforcementdescriptiondialog,specifythesameparametersasforrebarnumber3,andclickOK.
Usingthemethodlearnedpreviously,definethelocationofthe
distributionlineandthedescription.
Ifnecessary,dragthestirrupdescriptionssothatthefinalcross
sectionlooksasshown.
NOTEPayattentiontothecommandlineasyoudefinerebar.
2 DefinecrosssectionBB:ClickHomeModify (Copy).Alternatively,clickModifymenu
Copy.Inthedrawingarea,selectcrosssectionAA(withoutits
designationAA)astheobjecttocopy.
Clicknexttotheexistingsectiontoplacethecopy.
Selectthedescriptionsofthestirrupsinthecopiedcrosssection,
rightclick,andclickModify.
IntheReinforcementdescriptiondialog,clearActive.
26
5/28/2018 Belajar Structural Detailing
30/41
NOTETurningofftheActiveparameterkeepsthebarfrombeingincluded
inthereinforcementtable,thusavoidingduplicationduringcalculations
(thereinforcementpositioninsectionAAremainsactive).
ClickClose.
Repeatthe
last
3steps
for
rebar
number
2and
number
3(bottom
andupperreinforcement)inthecopiedcrosssection.Makethem
inactive.
ClickASD ReinforcementGraphicelements (Insert
sectionsymbol).Alternatively,clickReinforcementmenuGraphic
elementsInsertsectionsymbol.
NOTETheoptionletsyouinsertasectionsymbolataselectedplaceina
drawing.Symbolsaredrawnaccordingtothedefaultstylespecifiedinthe
JobPreferencesdialog.
Onthecommandline,typeBtoassignthedesignationtothe
definedsection,andthenpressEnter.
Inthedrawingarea,clicktospecifyfirstandsecondpointsofthe
sectiondesignation,andthenspecifythelocationofthesection
description(seetheimagebelow).
27
5/28/2018 Belajar Structural Detailing
31/41
NOTEInthecopiedcrosssection(BB),therearestirrupswithlongitudinal
rebaralreadydefined.Onlyrebarnumber4requiresinformation.
ClickASD ReinforcementReinforcementdefinition
(Reinforcementpoint). Alternatively,clickReinforcementmenu
Reinforcementpoint.
Inthedrawingarea,selectrebarnumber4.
IntheReinforcementpointdialog,click .
Click (Insert).
Inthedrawingarea,define2rebarsasshown,andtheninsertthe
rebardescriptions.
IncrosssectionBB,verifythatpositionnumber4isactive(select
thedescription,rightclick,andclickModify).
3 DefinecrosssectionCC:ClickHomeModify (Copy).Alternatively,clickModifymenu
Copy.
Inthedrawingarea,selectcrosssectionBB(withoutitsdesignation
andwithout
rebar
number
4)
as
the
object
to
copy.
Clicknexttotheexistingsectiontoplacethecopy.
ClickASD ReinforcementGraphicelements (Insert
sectionsymbol).Alternatively,clickReinforcementmenuGraphic
elementsInsertsectionsymbol.
28
5/28/2018 Belajar Structural Detailing
32/41
Onthecommandline,typeCtoassignthedesignationtothedefinedsection,andthenpressEnter.
Inthedrawingarea,clicktospecifyfirstandsecondpointsofthe
sectiondesignation,andthenspecifythelocationofthesection
description(see
the
image
below).
ClickASD
Reinforcement
Reinforcement
definition
(Reinforcementpoint).Alternatively,clickReinforcementmenu
Reinforcementpoint.
Inthedrawingarea,selectrebarnumber4.
IntheReinforcementpointdialog,click .
Click (Insert).
Inthe
drawing
area,
define
2rebars
as
shown,
and
then
insert
the
rebardescriptions.
Makesurethatallpositionsareinactiveinthiscrosssection.
Proceedtothenextexercise,CreatingaColumnandaSpread
Footing.
29
5/28/2018 Belajar Structural Detailing
33/41
CreatingaColumnandaSpreadFooting
Inthisexercise,youwillusemacrostocreateacolumnandaspreadfooting.Ifyou
havetypicalstructuralelementsinyourmodel,youcanusemacrosinthe
Reinforcementmoduletogeneratereinforcementandformworkautomatically.
1 Createacolumn:ClickASD StructureElementsStructureelements
reinforcement (Column).Alternatively,clickReinforcement
menuTypicalstructures reinforcementColumn.
IntheReinforcementofcolumnsdialog,ontheGeometrytab,
specifythegeometryparametersasshown.
NOTEThefirststageofdefiningacolumnissimilartothefirststageof
definingformworkwhenusingthemacro.
Inthesecondstage,definereinforcementparametersofthe
column.OntheStirrupstab,specifythestirrupsparametersas
shown.
30
5/28/2018 Belajar Structural Detailing
34/41
OntheBarstab,specifythebarsparametersasshown.
ClickOK.
Inthedrawingarea,clicktospecifyaninsertionpoint.
Deletethetablethatcontainsreinforcement,whichwasgenerated
automaticallyinthemodelspace.
2 Createaspreadfooting:ClickASD StructureElementsStructureelements
reinforcement
(Spread
footing).
Alternatively,
click
ReinforcementmenuTypicalstructures reinforcementSpread
footing.IntheSpreadfootingdialog,ontheGeometrytab,specify
theparametersasshown.
31
5/28/2018 Belajar Structural Detailing
35/41
Inthesecondstage,definereinforcementparametersofthespread
footing.OntheBottombarstab,specifythebarsparametersas
shown.
OntheDowelstab,specifythedowelsparametersasshown.
OntheStirrupsinthepiertab,specifythestirrupsparametersas
shown.
32
5/28/2018 Belajar Structural Detailing
36/41
ClickOK.
Inthedrawingarea,clicktospecifyaninsertionpoint.
Deletethe
table
that
contains
reinforcement
which
was
generated
automaticallyinthemodelarea.
NOTEYoucansaveyourmacrosettingsbyusingamacrotemplate
(differentthantheprojecttemplate).Yoursettingswillbeavailablelaterin
thecurrentprojectandalsoineverynewproject.
3 UsingcommonAutoCADcommands(suchasMove,Copy,andErase),putallelements(beam,column,spreadfooting)intotheframe.
33
5/28/2018 Belajar Structural Detailing
37/41
4 Createtherightsideoftheframe:Inthedrawingarea,selectthecolumn,spreadfootingandbendbar
ofthebeam(#4).
ClickHome
Modify
(Mirror).
Alternatively,
click
Modify
menuMirror.
Clickaboveandbelowthebeamatthemidpointtospecifythefirst
andsecondpointsofthemirrorline.
5 Proceedtothenextexercise,AddingMaterialTakeoffs.
AddingMaterialTakeoffs
Inthisexercise,youwillcreatematerialtakeoffs.Calculatingtheamountofrebar
usedinaprojectistimeconsuming,andifanychangesaremade,thecalculations
needtoberedone.UsingtheTablestoolbarinAutoCADStructuralDetailing,youcan
automatetheprocessfortheinitialcalculationsandforanyrecalculationsneeded.
1 ClickASD ReinforcementTables (Maintable).Alternatively,clickReinforcementmenuReinforcementtableBars
Maintable.
2 AcceptonthecommandlinebypressingEnter,andclickinthedrawingareatoaddthetableintomodelspace.
3 ClickASD ReinforcementTables (Bars Summarytable).Alternatively,clickReinforcementmenuReinforcementtableBars
Summarytable.
4 AcceptonthecommandlinebypressingEnter,andclickinthedrawingareatoaddthetableintomodelspace.
5 ClickASD ReinforcementSettings (Preferences).Alternatively,clickReinforcementmenuPreferences.
6 OntheReinforcementtaboftheOptionsdialog,underGeneralsettings,verifythatUpdateexistingreinforcementtableoptionisselected.
7 ClickOK.34
5/28/2018 Belajar Structural Detailing
38/41
8 Inthedrawingarea,selectthedescriptionofbarnumber4intherightcorner,rightclick,andclickModify.
9 IntheReinforcementdescriptiondialog,forNumber,enter2.10
Click
Close.
NOTEThetableshavebeenupdated,andallinformationaboutthe
reinforcementshavebeenupdated.
11 Proceedtothenextexercise,DefinitionofViews.
35
5/28/2018 Belajar Structural Detailing
39/41
DefinitionofViews
Thesecondstageoftheprojectistocreateviews.Inthisexercise,youwillcreate
viewsinthemodelspace.
1 Creationaviewofframe.ClickASD ReinforcementTools (Createview).
Alternatively,clickReinforcementmenuToolsCreateview.
Inthedrawingarea,definetheareaoftheviewbyclickingtospecify
thefirstandsecondcornersoftheplane.Includethewholeframe,
withouttablesandcrosssections.
TypeFramefortheviewname.
Definetheviewscaleas1:20.
NOTEAviewisasingleelementwithitsownscale.
2 Createviewsofcrosssections:ClickASD ReinforcementTools (Createview).
Alternatively,clickReinforcementmenuToolsCreateview.
DefinetheareaofviewtoincludethecrosssectionofbeamAA.
Forviewname,typeSectionAA.
Definetheviewscaleas1:10.
Usingthesamemethodandparameters,createviewsforthe
remainingcrosssections.
3 Createviewsoftables:ClickASD ReinforcementTools (Createview).
Alternatively,click
Reinforcement
menu
Tools
Create
view.
DefinetheareaofviewtoincludetheBarsMaintable.
Forviewname,typeBarsMaintable.
Definetheviewscaleas1:20.
36
5/28/2018 Belajar Structural Detailing
40/41
Usingthesamemethod,createaviewfortheBars Summarytable.
Theresultinglistofviewsshouldbeasshown.
4Proceed
to
the
next
exercise,
Creating
Sheets
and
Adding
Views.
CreatingSheetsandAddingViews
Inthisexercise,youwillcreatethefinalshopdrawing.Inthisstageofeveryproject,
alloperationsareperformedinprintoutlayouts.
1 OntheAutoCADlayouttab,rightclick,andclickFromtemplate.NOTEAprintoutlayoutisanAutoCADobject.Itisusedforthecomposition
ofafinalprintout.Foreachprintoutlayout,thereisoneprintout.Whenyou
layoutelementsontheprintout,youworkwithviews.Whenyouchangethe
scaleofaview,italsoimpactsthefinaldrawing.
2 IntheSelectTemplateFromFiledialog,selectanA1formattemplate(forexample,A1ASD033.dwt).
37
5/28/2018 Belajar Structural Detailing
41/41
3 IntheInsertLayout(s)dialog,clickOK.4 ClicktheA1ASDtab.5 OnthePositionstaboftheInspector,selectFrame,rightclick,andclickAdd
to
current
Printout.
6 Inthedrawingarea,clicktospecifythebasepoint.7 Repeatthelast2stepsfortheremainingviews,andarrangethefinaldrawingasshown.
YouhavecompletedtheAutoCADStructuralDetailing2011ReinforcementModule
GettingStartedGuide.
38