INTERNATIONAL JOURNAL OF ENVIRONMENTAL SCIENCES Volume 3, No 2, 2012
Copyright by the authors - Licensee IPA- Under Creative Commons license 3.0
Research article ISSN 0976 4402
Received on August 2012 Published on September 2012 895
Heavy metal fate during co-incineration of organic waste of pharmaceutical
industry Narsimha Reddy M
1, Sripathi S
1, Mohan Reddy C
2, Venkateswara Reddy V
3
1 - EHS Department Hetero Labs Limited (Unit-I) , Medak - Dist., Pin Code No: 502 319,
Andhra Pradesh, India
2- Director (Operations) Hetero Labs Limited (Unit-I).
3- Professor in Department of Civil Engineering (Environment Section), JNTUH,
Hyderabad- 500 084
doi:10.6088/ijes.2012030132017
ABSTRACT
During the production of the life saving drugs in a pharmaceutical industry, there will be
generation of the organic waste which is inevitable. The safe disposal of the waste is a
pressing issue for these industries; though the incineration process is available such industries
are looking for the more eco friendly disposal methodologies. Energy recovery by means of
combustion in Waste-to-Energy or conservation of fossil fuels by the replacement in the
energy intensive production process such as cement industries is a viable possible
application. Currently, there are various norms for co-incineration and concern for heavy
metal fate in view of the possible bio magnification. The results demonstrated no variability
in the heavy metal effects to the environment either through emissions or in the form of the
solid waste. The result suggests not only technical and economic feasibility of
co-incineration method, but also the feasibility of adopting the co-incineration process for the
disposal of the pharmaceutical waste.
Keywords: Co-incineration, Pharmaceutical Organic Waste, Heavy Metals, Cement Rotary
kilns, Toxicity Leachate Procedures, SW846.
1. Introduction
Today the pharmaceutical industry can be characterized as high technology industry with
very deep historical roots which were less scientific at lease when considered with todays
measures dating back to the ancient Egyptians. Over the last three decades the Indian
pharmaceutical industry has transformed into a world leader in the production of high quality
generic drugs. The Indian pharmaceutical products are exported to more than 200 countries
around the globe including highly regulated markets of USA, Europe, Japan, Africa and
Australia. Significant growth was witnesses in the therapeutical segments like cardiac,
diabetes and Central Nervous system (CNS). India is also increasingly emerging as one of the
most globally preferred outsourcing destination for pharmaceutical. This trend can be largely
attributed to India's inherent competencies in terms of manufacturing cost, vast talent pool
having outstanding chemistry skills, diverse patient pool, and strong support from auxiliary
industries such as bio-informatics, clinical data management etc and a favorable regulatory
environment. Indian pharmaceutical industry is now broadening the scope of its service
offerings by providing a wide range of services spanning the entire pharmaceutical value
chain. With such a rapid pace of development, pharmaceutical industries are also keeping
tremendous efforts on waste management.
Heavy metal fate during co-incineration of organic waste of pharmaceutical industry
Narsimha Reddy. M, Sripathi. S, Mohan Reddy. C, Venkateswara Reddy. V International Journal of Environmental Sciences Volume 3 No.2, 2012
896
Pharmaceutical industries generate the organic waste during the reaction and distillation
process, these wastes on performing comprehensive analysis is found to have calorific values
ranging above 5000 Kilocalories and are hazardous in nature as per the Hazardous waste
management (HWM) rules, 2008 Government of India, the average the analysis reports is
given in table 1, Hence, these Pharmaceutical Organic Wastes (POW) are to be properly
disposed by incineration. Present trend is the disposal of the waste by direct incineration by
captive incinerator or disposed to common incineration facility.
Table 1: Average the analysis results for pharmaceutical organic wastes (POW)
S. No Parameter Unit Method Average Results
1 pH -- SW-846 9045C 6.07
2 Loss on Ignition at 550o C % APHA 2540 93.37
3 Paint filter liquid Test -- SW-846 9095A Fail
4 Bulk density / Specific
Gravity g/cc ASTM D 5057-90 1.24
5 Calorific Valve Cal/gm IS: 1350-1970 5997.33
6 Flash Point oC SW-846 1020A 30.50
7 Total halides as Cl- % SW 846 5.27
This disposal method involves the air emissions, green house gas generations and certain
amount of solid waste in the form of ash. The ash generated is again to be disposed to the
secured landfill which will create burden on the land. In view of the same pharmaceutical
industries is looking for the cost reduction, energy conservation and eco-friendly option to
minimize the environmental impacts. Co-incineration in cement kilns provided a viable
option, wherein the pharmaceutical waste replaces a part of the traditional fuels.
Cement kilns have traditionally been fired by coal but use of the pharmaceutical organic
waste as alternative fuels offer the joint benefits of improved performance and lower
production costs. The fact that the energy costs have a considerable influence on a large part
of the production costs (the share amounts to about one third) leads many manufacturers to
reduce consumption of conventional sources of energy in favor of alternative fuels. In other
words, alternate fuels also offer conservation of traditional fuels.
The following reasons underline the advantages of using the rotary kiln for the co-
incineration of these fuels along with the traditional fuels coal/coke:
1. High temperature in the fuels and in the gas phase;
2. Long staying (residence time of 4-5 minutes) of the fuels in the oxygen rich burning process (favoring a complete burning);
3. Counter current flow of raw material and flue gases - Intense contact and interactions between solid and gas phases in the heat exchanger system;
4. Kiln lines are equipped with efficient pollution control equipment;
5. Any acid gases are neutralized by the raw material being of an alkaline nature and subsequently incorporated into the cement clinker;
6. The recycling (ashes) resulting from the burning are absorbed in the clinker in an idle manner and practically irreversible manner;
Heavy metal fate during co-incineration of organic waste of pharmaceutical industry
Narsimha Reddy. M, Sripathi. S, Mohan Reddy. C, Venkateswara Reddy. V International Journal of Environmental Sciences Volume 3 No.2, 2012
897
7. Use of alternative fuels is estimated to contribute a global average reduction in CO2 emissions from the cement industry of 12% by 2020.
All characteristics mentioned above become evident in each cement rotary kiln independently
from the type of kiln. This fact leads to the conclusion that the rotary kiln is really
predestined for the use of these fuels and disposal of the waste.
2. Materials and method
The present study focus on the heavy metal concentration in the basic fuels ( Coal/Coke) and
the hazardous waste and their fate while co-incineration process at cement kilns are reviewed
with focus to the upcoming environmental norms and interests. Cement plant located at
Reddypalem, Tamilnadu is selected for the purpose of the study, whose capacity is 3.8
MMTA and it is having a single stream rotary kiln with four preheaters. The methodology is
based on the mass balance approach and hence the comprehensive analysis of the fuels,
emissions and the clinker had been carried out during the course of the study. It is evident
that the chemical composition of the raw meal, fuels and sludge will greatly influence the
quality of the flue gas emissions from kiln/ raw mill stack. Coal and Coke samples and the
sludge samples were collected before the trial run whereas the raw meal sample is collected
while the trial run is in progress.
3. Sample preparation
Analysis of the fuels/ raw material
A representative sample of the coal/coke, raw meal and the pharmaceutical waste is collected
and are subjected to the proximate and ultimate analysis for the establishment of the metal
constituents. The analysis results of the samples are shown in Table-2, 3, 4 &5.
Table 2: Raw meal - chemical composition
Sr. No. Parameters UOM Results
1 Fluorides as F mg/kg 12.14
2 Sulphates as SO4 mg/kg 29.86
3 Aluminum as Al203 mg/kg 58
4 Silica as Si02 mg/kg 4126.4
5 Iron as Fe mg/kg 19647.8
6 Cadmium as Cd mg/kg 1.1
7 Chromium as Cr mg/kg 47.5
8 Copper as Cu mg/kg 3.5
9 Cobalt as Co mg/kg 0
10 Manganese as Mn mg/kg 250.0
11 Nickel as Ni mg/kg 40.4
12 Lead as Pb mg/kg 90.8
13 Zinc as Zn mg/kg 18.4
14 Arsenic as As mg/kg 12.4
15 Mercury as Hg mg/kg 2.1
16 Selenium as Se mg/kg 2.8
17 Antimony as Sb mg/kg 5.2
18 Vanadium as V mg/kg 61.2
Heavy metal fate during co-incineration of organic waste of pharmaceutical industry
Narsimha Reddy. M, Sripathi. S, Mohan Reddy. C, Venkateswara Reddy. V International Journal of Environmental Sciences Volume 3 No.2, 2012
898
Table 3: Fuels Proximate analysis
Sr. No. Parameters UOM Coal Pharmaceutical
Organic Waste
1 Moisture Content % 2.24 8.63
2 Ash Content % 52.46 7.18
3 Volatile Matter % 22.46 91.58
4 Fixed Carbon % 21.24 1.24
Table 4: Fuels Ultimate Analysis
Sr. No. Parameters UOM Coal Pharmaceutical
Organic Waste
1 Mineral Matter % 32.48 NA
2 Carbon % 78.64 48.84
3 Hydrogen % 3.90 3.87
4 Nitrogen % 1.04 4.79
5 Sulphur % 5.46 13.24
6 Oxygen % 10.96 29.26
7 Gross Calorific Value K.Cal/Kg 5240.0 5997.33
8 Chlorine as Cl mg/Kg NA 5.27
9 Fluorine as F mg/Kg NA NA
Table 5: Metal analysis
Sr. No. Parameters UOM Coal Pharmaceutical Organic
Waste
1 Cadmium as Cd mg/Kg 0.32 0.3
2 Chromium as Cr mg/Kg 10.5 5.0
3 Copper as Cu mg/Kg 11.6 5.0
4 Iron as Fe mg/Kg 2314 125.0
5 Cobalt as Co mg/kg 6.8 0.02
6 Manganese as Mn mg/Kg 17.3 5.1
7 Nickel as Ni mg/Kg 173 0.07
8 Lead as Pb mg/Kg 5.5 0.05
9 Zinc as Zn mg/Kg 48.9 56.7
10 Arsenic as As mg/kg 0.46
Heavy metal fate during co-incineration of organic waste of pharmaceutical industry
Narsimha Reddy. M, Sripathi. S, Mohan Reddy. C, Venkateswara Reddy. V International Journal of Environmental Sciences Volume 3 No.2, 2012
899
on a heated filter, and gaseous emissions are then collected in an aqueous acidic solution of
hydrogen peroxide (analyzed for all metals including Hg) and an aqueous acidic solution of
potassium permanganate (analyzed only for Hg). The recovered samples are digested, and
appropriate fractions are analyzed for Hg by Cold Vapor Atomic Absorption Spectroscopy
(CVAAS) and for Sb, As, Ba, Be, Cd, Cr, Co, Cu, Pb, Mn, Ni, P, Se, Ag, Tl, and Zn by
Inductively Coupled Plasma Atomic Emission Spectroscopy (ICP-AES) and shown results as
Table-6, 7 & 8 also shown Figure-1 for The Heavy metal emission Trend. ICP-AES used for
this analysis is,
Make : Varion Model : Vista
TYPE : CCD Simultaneous mode
Carrier Gas : Nitrogen 99%
Fuel Gas : Argon 99%
Ignition Type : Automatic by RF Power
Range of elements : 23 E, V, As, Hg, Se, Pd, Sn, Mo, Sb, 71/72 elements
Table 6: Results of all metals emissions after co-incineration with 10%
pharmaceuticals organic waste (results in g/nm3)
Samples As Cd Co Cr Cu Hg Mn Ni Pb Sb Se Th Z
n
1 0.9 2.4 2.5 11.
5 6.5 0.5 32.2 8.7 5.0 8 1.9
Heavy metal fate during co-incineration of organic waste of pharmaceutical industry
Narsimha Reddy. M, Sripathi. S, Mohan Reddy. C, Venkateswara Reddy. V International Journal of Environmental Sciences Volume 3 No.2, 2012
900
Table 8: Results of all metals emissions after co-incineration with normal fuel = 0% POW,
(results in g/nm3)
Samples As Cd Co Cr Cu Hg Mn Ni Pb Sb Se Th Zn
1 1.1 2.1 3.5 13 6.6 0.5 32.4 8.2 4.8 15.
2 1.5
Heavy metal fate during co-incineration of organic waste of pharmaceutical industry
Narsimha Reddy. M, Sripathi. S, Mohan Reddy. C, Venkateswara Reddy. V International Journal of Environmental Sciences Volume 3 No.2, 2012
901
4 Iron as Fe mg/Kg
Heavy metal fate during co-incineration of organic waste of pharmaceutical industry
Narsimha Reddy. M, Sripathi. S, Mohan Reddy. C, Venkateswara Reddy. V International Journal of Environmental Sciences Volume 3 No.2, 2012
902
and Dr. P Manikyamba, Retired Professor, Department of Chemistry, Kakathiya University,
Warangal for their valuable suggestions during this study.
5. References
1. ALF-CEMIND Project: Supporting the use of alternative fuels in the cement industry Specific support action, the sixth frame work programme for research, Technological
development and demonstration.
2. Amalendu Bagchi, (2004), Design of landfills and integrated solid waste management, 3rd Edition, John Willy and Sons, Inc 64, 81-84, 398.
3. Anjaneyulu, Hazardous waste management, (2011), Allied publishers, 2nd edition.
4. B922-1 December, 2006 Emission Inventory Guidebook pp-110.
5. B922-1 December, 2006 Emission Inventory Guidebook.
6. Carlo Trozzi., (2006) B922-1 December, Emission Inventory Guidebook, 5-6.
7. Criteria for hazardous waste landfills CPCB guidelines 2000. pp-30
8. Gabbard. W. D., and Gossman D., (1990), Hazardous waste fuels and the cement kilns The Incineration Alternative, available at http://gcisolutions.com/HWF&CKS.htm,
accessed during 10 March 2011.
9. Guidelines for common hazardous waste incineration (June, 2005), available at http:// www.cpcb.nic.in, accessed during March 2011.
10. Hazardous waste management (HWM) rules, (2008), Government of India.
11. Henk J van de wiel (2003), determination of elements by ICP-AES and ICP-MS, pp-17.
12. George Tchobanoglous, Hilary Theisen & Sammuel A. Vigil, (2000), Integrated solid waste management Kntee et al., 1
st edition, ISBN-10: 0070632375.
13. The impact of alternative fuels on the cement manufacturing process. In: proc. Of R2000 Recovery, Recycling and Reintegration. June 2000, Toronto (OT), Canada: 1070-1075
(on CD-ROM).
14. Kntee et al., (2004), Cement manufacturing using alternative fuels and the advantages of process modeling. Fuel processing technology, 85, pp 293-301.
15. Karlsson et al., (1996), Laboratory characterization of the waste tyre particle for combustion in a cement klin. In: Proc. of the Finnish-Swedish Flame Days, Naantali,
Finaland. Sept 3-4, pp 18.
16. Laurent Bontoux, (March 1999), A report prepared by IPTS for the committee for environment, Public health and consumer protection of the European parliament, EUR
18717 EN. Pp 12, 20.
Heavy metal fate during co-incineration of organic waste of pharmaceutical industry
Narsimha Reddy. M, Sripathi. S, Mohan Reddy. C, Venkateswara Reddy. V International Journal of Environmental Sciences Volume 3 No.2, 2012
903
17. Ministry of Environment and forests Notification, New Delhi, the 24th September, 2008. pp 9.
18. Moses P.M. Chinyama, (2011), Alternative fuels in cement manufacturing, doi: 10.5772/22319.
19. Mukherjee et al., (2001), Proc. of the 6th Int. Conf. on the biogeochemistry of trace elements, Guelph (ON), Canada, Jul, 29 Aug. 2, 2001, p 379. The effects of switching
from coal to alternative fuels on heavy metals Emissions from cement manufacturing.
20. Murat M, and Sorrentino F., (1996), Effects of large additions of Cd, Pb, Cr, Zn to cement raw meal on composition and properties of clinker and the cement. Cement and
concrete research, 26 (3), pp 377 385.
21. Murray, A, Price, L., (2008), Use of alternative fuels in cement manufacture: Analysis of fuel characteristics and feasibility of use in the Chinese cement sector,
Ernest Orlando Lawrence Berkeley National Laboratory, 10 March, 2011,
http://ies.lbl.gov.iespubs/LBNL-525E.pdf
22. Panagiota Dilara., (2006), B925-2 December, Emission Inventory Guidebook, 7.
23. Research on feasibility of different incineration systems for Paper sludge, Proceeding of the 17
th Annual North American Waste-to-Energy Conference (NAWTEC17) American
Waste-to-Energy Conference.
24. S.N. Ghosh., (1991), Cement and concrete science & technology. (Vol. 1, Part 1), ABI Books Private Limited.
25. Section V.B: Cement kilns firing hazardous waste, DRAFT 15/04/04 Draft Guidelines on BAT and BEP for Cement Kilns Firing Hazardous Waste.
26. Tiggesbumker P, and Beckum K.M., (1986), Investigations on combustion of solid fuels in calciners. Zemet-Kall-Gips, 4, pp 104 106.
27. Ursula Kntee et al., (2002), Cement manufacturing using alternative fuels and the advantages of Process Modelling, Presented at R2002 Recovery, Recycling, Re-
integration, February 12 15, Geneva (Switzerland), available at http://www.R2002.com,
accessed during July 2011.
Recommended