JdTRANS T02 LCDProgrammierbarer
Messumformerprogrammable
transmitter
B 95.6522Betriebsanleitung
Operating Instructions08.01/00384950
Bedienübersicht
1 Typenerklärung
Serienmäßiges Zubehör
- 1 Betriebsanleitung B 95.6522
Zubehör
- PC-Setup-Programm, mehrsprachig
- PC-Interfaceleitung mit TTL/RS232-Umsetzer und Adapter
JUMO dTRANS T02 LCD(1) Grundausführung
956522 programmierbarer Messumformer
(2) Eingang (programmierbar)x 888 Werkseitig eingestellt (Pt100 DIN vl / 0 … 100°C)x 999 Konfiguration nach Kundenangaben1
(3) Ausgang (eingeprägter Gleichstrom - programmierbar)x 888 Werkseitig eingestellt (0 … 20mA)x 999 Konfiguration nach Kundenangaben
(0/4 … 20mA oder 0/2 … 10V)(4) Spannungsversorgung
x 22 AC/DC 20 … 53V, 48 … 63Hzx 23 AC 110 … 240V +10/-15%, 48 … 63Hz
(1) (2) (3) (4)Bestellschlüssel / - -Bestellbeispiel 956522 / 888 - 888 - 23
1 Bei der Konfiguration nach Kundenangaben sind die Fühlerart und der Messbereich im Klartext anzugeben
1
2 Installation
Anschlussplan
Anschluss fürSpannungsversorgung lt. Typenschild
Analoge EingängeThermoelement
Widerstandsthermometer / Potentiometerin Zweileiterschaltung
RL ≤ 30Ω (RL = Gesamtleitungswiderstand)Widerstandsthermometer / Potentiometerin Dreileiterschaltung
Widerstandsthermometer / Potentiometerin Vierleiterschaltung
2
2 Installation
Widerstandsferngeber in Dreileiterschaltung
Spannungseingang < 1V
Spannungseingang ≥ 1V
Stromeingang
Analoge AusgängeSpannungsausgang
Stromausgang
Digitale AusgängeOpen-Collector-Ausgang 1
v Siehe “Anschlussbeispiele” auf Seite 29.
Open-Collector-Ausgang 2
v Siehe “Anschlussbeispiele” auf Seite 29.
Setup-Schnittstelle
A Die Setup-Schnittstelle und der analo-ge Ausgang sind nicht galvanisch ge-trennt.v Siehe “Setup-Schnittstelle” auf Seite 5.
3
2 Installation
Installationshinweise
! Sowohl bei der Wahl des Leitungsmaterials bei der Installationals auch beim elektrischen Anschluss des Gerätes sind die Vor-schriften der VDE 0100 „Bestimmungen über das Errichten vonStarkstromanlagen mit Nennspannungen unter 1000V“ bzw. diejeweiligen Landesvorschriften zu beachten.
! Der elektrische Anschluss, sowie Arbeiten im Geräteinnerendürfen ausschließlich von Fachpersonal durchgeführt werden.
! Das Gerät allpolig vom Netz trennen, wenn bei Arbeiten span-nungsführende Teile berührt werden können.
! Ein Strombegrenzungswiderstand (Sicherheitsfunktion) unter-bricht bei einem Kurzschluss im Messumformer den Netz-stromkreis. Die äußere Absicherung der Spannungsversorgungsollte einen Wert von 1A (träge) nicht überschreiten.
! In der Nähe des Gerätes keine magnetischen oder elektrischenFelder, z. B. durch Transformatoren, Funksprechgeräte oder
elektrostatische Entladungen entstehen lassen1.
! Induktive Verbraucher (Relais, Magnetventile etc.) nicht in Gerä-tenähe installieren und durch RC- oder Funkenlöschkombina-tionen bzw. Freilaufdioden entstören.
! Eingangs-, Ausgangs- und Versorgungsleitungen räumlich von-einander getrennt und nicht parallel zueinander verlegen. Hin-und Rückleitungen nebeneinander führen und nach Möglichkeitverdrillen.
! Alle Ein- und Ausgangsleitungen ohne Verbindung zum Span-nungsversorgungsnetz müssen mit geschirmten und verdrilltenLeitungen verlegt werden (nicht in der Nähe stromdurchflosse-ner Bauteile oder Leitungen führen). Die Schirmung muss gerä-teseitig auf Erdpotential gelegt werden.
4
2 Installation
Setup-Schnittstelle
! An die Netzklemmen des Gerätes keine weiteren Verbraucheranschließen.
! Das Gerät ist nicht für die Installation in explosionsgefährdetenBereichen geeignet.
! Ein vom Anschlussplan abweichender elektrischer Anschlusskann zur Zerstörung des Gerätes führen.
! Bei störungsbelasteten Netzen (z. B. Thyristorsteuerungen) soll-te das Gerät über einen Trenntransformator gespeist werden.
! Netzschwankungen sind nur im Rahmen der angegebenen To-
leranzen zulässig1.
1 siehe Typenblatt
A Die Setup-Schnittstelle und der analoge Ausgang sind nichtgalvanisch getrennt. Unter ungünstigen Umständen könnendaher, bei einem eingebauten Messumformer, Ausgleichs-ströme fließen, wenn das PC-Interface angeschlossen wird.Die Ausgleichsströme können Schäden bei den beteiligtenGeräten bewirken.
Keine Gefahr besteht, wenn der Ausgangsstromkreis desMessumformers galvanisch von Erde getrennt ist. Wennnicht sichergestellt ist, dass bei einem eingebauten Mess-umformer der Ausgangskreis galvanisch getrennt ist, sollteeine der folgenden Sicherheitsmaßnahmen verwendet wer-den:
Einen Rechner ohne galvanische Kopplung mit Erde ver-wenden (z.B. einen Notebook im Batteriebetrieb) oder denAusgang des Messumformers abklemmen bevor das PC-In-terface angeschlossen wird.
5
2 Installation
Abmessungen
6
3 Anzeige- und Bedienelemente
Betriebszustand in der Bedienerebene(Normalbetrieb)
Leucht-/Blinkverhalten
Limitkomparator 1 inaktiv2 inaktiv
Limitkomparator 1 aktiv2 inaktiv
Limitkomparator 1 inaktiv2 aktiv
Limitkomparator 1 aktiv2 aktiv
Overrange
Tasten zur Bedienung
LCD-AnzeigeSchnittstelle für PC-Setup-Programm
LEDs für BetriebszustandP = Power LEDS = Status LED
ohne Bedeutung, nurfür interne Zwecke
7
3 Anzeige- und Bedienelemente
Unterscheidung der Betriebszustände
- Im Betriebszustand Bedienerebene ist die Power-LED permanent an.
- Im Betriebszustand Parameterebene blinkt diePower-LED (zu gleichen Teilen an und aus).
Betriebszustand in der Parameterebene(Programmier-Modus)
Leucht-/Blinkverhalten
Grenzwert vonLimitkomparator 1
Grenzwert vonLimitkomparator 2
Feinabgleich (Nullpunkt)
Feinabgleich (Endwert)
Teach In (0-%-Wert)
8
4 Funktionen und Bedienung
Mit Hilfe der Tasten q, d und i in Verbindung mit der LCD-Anzei-ge und den in Kapitel 3 „Anzeige- und Bedienelemente“ bereits be-schriebenen Blinkzyklen der beiden LEDs „Power“ und „Status“können Sie den Messumformer bedienen und programmieren.
Bei der Bedienung unterscheiden sich drei Betriebszustände:
- Bedienerebene (Normalbetrieb)
- Parameterebene (Programmier-Modus)
- Konfigurationsebene (Programmier-Modus)
BedienerebeneIn der Bedienerebene befindet sich der Messumformer 2 Sekundennach dem Anlegen der Versorgungsspannung, oder wenn die Para-meterebene bzw. Konfigurationsebene verlassen wurde.
ParameterebeneIn die Parameterebene gelangen Sie aus der Bedienerebene durchBetätigen der Taste q (mindestens 2 Sekunden lang). In der Ebenekönnen folgende Funktionen programmiert werden:
- Grenzwert des 1. Limitkomparators AL1
- Grenzwert des 2. Limitkomparators AL2
- Feinabgleich (Nullpunkt - 0%) OUTL
- Feinabgleich (Endwert - 100%) OUTH
- Teach In OFFS
Die Parameterebene wird verlassen (beendet), nachdem Sie denParameter „Teach In“ editiert haben oder mindestens 20 Sekundenlang keine Taste oder die Tastenkombination q + d betätigen.
Die einzelnen Parameter können nacheinander verändert werden.Von Parameter zu Parameter gelangen Sie durch Betätigen derTaste q.
9
4 Funktionen und Bedienung
KonfigurationsebeneIn die Konfigurationsebene gelangen Sie aus der Parameterebenedurch Betätigen der Taste q (mindestens 2 Sekunden lang).
In der Ebene können folgende Funktionen programmiert werden:
- Fühlerart C111
- Linearisierung C112
- Anzahl der Nachkommastellen C113
- Einheit des Messwertes C002
- Netzfrequenz und Temperatur-Kompensation C114
- Temperaturkompensation-Festwert C115
- Messwert-Anzeige C116
- Funktion der Analogausganges C211
- Signal bei Fühlerbruch/-kurzschluss C212
- Funktion des Binär-Ausganges 1 C221
- Signal bei Fühlerbruch/-kurzschluss C222
- Schaltdifferenz (Hysterese) unten C223
- Schaltdifferenz (Hysterese) oben C224
- Funktion des Binär-Ausganges 2 C231
- Signal bei Fühlerbruch/-kurzschluss C232
- Schaltdifferenz (Hysterese) unten C233
- Schaltdifferenz (Hysterese) oben C234
H Nur wenn in der Anzeige der Parameter OFFS aktiv ist unddie Konfigurationsebene gestartet wird, können die Para-meter verändert werden. Ist ein anderer Parameter aktiv,können Sie die aktuelle Einstellung nur lesen.
10
4 Funktionen und Bedienung
- Frequenz bei Messbereichsanfang C235
- Frequenz bei Messbereichsende C236
- Skalierung Startwert SCL
- Skalierung Endwert SCH
- Filterzeit DF
- Gesamtwiderstand bei Widerstandsferngeber R FE
- Simulation Istwertausgang C001
Die Konfigurationsebene wird verlassen (beendet), nachdem Sieden letzten Parameter editiert haben oder mindestens 20 Sekundenlang keine Taste oder die Tastenkombination q + d kurz betätigen.
Die einzelnen Parameter können nacheinander verändert werden.Von Parameter zu Parameter gelangen Sie durch Betätigen derTaste q.
11
4 Funktionen und Bedienung
Werte erhöhenBeim Programmieren der Parameter dient die Taste i zum Erhöheneines Wertes (+).
Werte verringernBeim Programmieren der Parameter dient die Taste d zum Verrin-gern eines Wertes (-).
Werte übernehmenWurde eine Einstellung geändert, müssen Sie die Taste q betäti-gen, um die Änderung zu übernehmen.
q hat eine doppelte Bedeutung:
- Übernahme von geänderten Werten
- Aufruf des nächsten Parameters
Wertkontrolle Mit Ausnahme der Parameter OUTL, OUTH und OFFS können Sie alleaktuellen Werte während der Programmierung mit Hilfe der LCD-Anzeige kontrollieren. Eine zusätzliche Kontrolle kann mit Hilfe einesSpannungsmessers am Spannungsausgang erfolgen.
H Ist die Parameterebene aktiv, wird bei der Programmierungder beiden Grenzwerte der Analogausgang nicht entspre-chend der Eingangsbeschaltung angesteuert, sondern mitdem aktuellen Grenzwert.
H Bitte beachten Sie, dass die Programmierung des Parame-ters „Teach In“ von der Standardbedienung abweicht.
v Siehe “Teach In” auf Seite 15.
12
4 Funktionen und Bedienung
Grenzwerte (Limitkomparatoren) einstellenSie können die beiden Grenzwerte AL1 und AL2 mit Hilfe der Tastend und i verändern. Der aktuelle Wert wird über den Ausgang aus-gegeben. Übernommen wird der Wert durch Betätigen der Taste q.
Die Schaltdifferenzen (Hysterese) können Sie mit den ParameternC223 und C224 bzw. C233 und C234 einstellen.
Bei der Grenzwertüberwachung stehen zwei Arten zur Verfügung.Welche eingesetzt wird, können Sie mit Hilfe des Parameters C221bzw. C231 entscheiden.
Funktionsweise lk7:
Funktionsweise lk8:
Natürlich lassen sich alle Parameter auch mit den als Typenzusatzerhältlichen PC-Setup-Programm einstellen.
13
4 Funktionen und Bedienung
Feinabgleich (Nullpunkt und Endwert)Mit Hilfe des Feinabgleiches können Sie den Nullpunkt und dieSteilheit des Ausgangssignales anpassen. Auch hier wird durch Be-tätigen der Tasten d und i der jeweilige Wert verändert und durchBetätigen der Taste q übernommen.
Am Ausgang wird der gemessene Istwert ausgegeben. Beim Null-punkt (OUTL) sollte dieser dem Ausgangssignal 0%, beim Endwert(OUTH) dem Ausgangssignal 100% entsprechen.
Die Formel für die Berechnung des neuen Istwertes lautet:
Istwert Messwertskaliert Endwert× Nullpunkt+=
14
4 Funktionen und Bedienung
Teach InDer Parameter „Teach In“ dient dazu, den 0-%-Wert festzulegen.
Am Ausgang wird während der Programmierung der Nullwert aus-gegeben (z.B. 4mA). Durch Betätigen der Tasten d oder i wirddie Übernahme des Wertes ermöglicht und mit q durchgeführt.Nach einem Timeout ohne Übernahme steht der alte Wert wiederzur Verfügung.
Beispiel:
Die Stellung eines Ventils wird von einem Potentiometer erfasst.Das Potentiometer hat einen Bereich von 50 bis 150Ω, wobei 50Ωdem geschlossenen Ventil entsprechen. Der Messbereich ist wiefolgt programmiert:
- Potentiometer 50 … 150 Ω
- Ausgang 0 … 20mA
Annahme:
Durch mechanische Toleranzen ist die Potistellung jedoch bei ge-schlossenem Ventil 52Ω, woraus sich ein Ausgangsstrom von0,4mA ergibt. Der Fehler kann durch die Funktion „Teach In“ wiefolgt beseitigt werden:
- Ventil schließen.
- Parameterebene aufrufen und OFFS auswählen (am Ausgang sollten dann 0,4mA anliegen).
- Taste d oder i betätigen, worauf sich der Ausgang auf 0mA ändern muss.
- Änderung durch Betätigen der Taste q bestätigen.
- die Parameterebene verlassen (entweder nach Timeout von 20soder durch gleichzeitiges Betätigen von q + d.
15
5 Konfigurations- und Parametertabelle
In den folgenden Konfigurations- und Parametertabellen können Siean der durch einen markierten Stelle (Spalte) Ihre Einstellungenprotokollieren. Die werkseitige Einstellung ist durch eine graue Hin-terlegung ( ) gekennzeichnet.
Parameter der Parameterebene
Parameter der KonfigurationsebeneMesseingang
Para-meter
Erklärung Werte-bereich
werkseitig X
Al1 Grenzwert des Limitkomparators 1
-1999 …+9999 Digit
0
AL 2 Grenzwert des Limitkomparators 2
-1999 …+9999 Digit
0
OUTL Feinabgleich 0%(Nullpunkt)
siehe “Feinabgleich (Nullpunkt und Endwert)” auf Seite 14
OTUH Feinabgleich 100%(Endwert)
siehe “Feinabgleich (Nullpunkt und Endwert)” auf Seite 14
OFFS Teach In siehe “Teach In” auf Seite 15
C111 Messwertgeber X0 Widerstandsthermometer in 3-Leiter-Schaltung1 Widerstandsthermometer in 4-Leiter-Schaltung2 Widerstandsthermometer in 2-Leiter-Schaltung3 Thermoelement4 Spannung bis 1000mV5 Spannung bis 10V6 Strom7 Widerstandsferngeber (wfg)8 Poteniometer 3-Leiter-Schaltung9 Poteniometer 4-Leiter-Schaltung
10 Poteniometer 2-Leiter-Schaltung
16
5 Konfigurations- und Parametertabelle
C112 Linearisierung X0 linear1 kundenspezifisch2 Pt 100 DIN3 Pt 500 DIN4 Pt 1000 DIN5 Pt 100 JIS6 Ni 1007 Ni 5008 Ni 10009 Typ „L“
10 Typ „J“11 Typ „U“12 Typ „T“13 Typ „K“14 Typ „E“15 Typ „N“16 Typ „S“17 Typ „R“18 Typ „B“19 Typ „D“20 Typ „C“
C113 Anzahl der Nachkommastellen X0 keine Nachkommastelle1 1 Nachkommastelle2 2 Nachkommsstellen
17
5 Konfigurations- und Parametertabelle
C002 Einheit des Messwertes
(nur wirksam, wenn Parameter C116 = 2siehe Seite 22)
X
Einheit LCD-Anzeige0 °C °C1 °F °F2 K K34 bar BAR5 mbar mBAR6 Pa PA7 kPa KPA8 s SEC9 ms mSEC
10 min min11 h H12 d d13 100ms 100mS14 ml/s mL/S15 ml/min mL/mn16 l/s L/SEC17 l/min L/min18 l/h L/H19 m³/s m3/S20 m³/min m3/mn21 m³/h m3/H22 1/s 1/SEC23 1/min 1/min24 1/h 1/H25 Hz HZ26 kHz KHZ27 MHz MHZ28 lx LX
18
5 Konfigurations- und Parametertabelle
29 mlx mLX30 klx KLX31 cd cd32 mcd mcd33 kcd Kcd34 µm µm35 mm mm36 cm cm37 m m38 km Km39 % %40 ‰ ‰41 ppm PPM42 ppb PPB43 µg µG44 mg mG45 g G46 kg KG47 t T48 µW µW49 mW mW50 W W51 kW KW52 MW MW53 mVA mVA54 VA VA55 kVA KVA56 mVAs mVAS57 VAs VAS
C002 Einheit des Messwertes
(nur wirksam, wenn Parameter C116 = 2siehe Seite 22)
X
Einheit LCD-Anzeige
19
5 Konfigurations- und Parametertabelle
58 kVAs KVAS59 J J60 µJ µJ61 mJ mJ62 kJ KJ63 Ws WS64 kWh KWH65 pH PH66 mΩ mOHM67 Ω OHM68 kΩ KOHM69 MΩ MOHM70 mm/s mm/S71 mm/h mm/H72 m/s m/SEC73 m/min m/MIN74 km/h Km/H75 %/s %/S76 m/s² m/S277 G G78 µl µL79 ml mL80 l L81 hl HL82 m³ M383 µV µV84 mV mV85 V V86 kV KV
C002 Einheit des Messwertes
(nur wirksam, wenn Parameter C116 = 2siehe Seite 22)
X
Einheit LCD-Anzeige
20
5 Konfigurations- und Parametertabelle
87 µA µA88 mA mA89 A A90 kA KA91 S S92 mS mS93 µS µS94 nH nH95 µH µH96 mH mH97 H H98 pF PF99 nF nF
100 µF µF101 mF mF102 F F103 mm² mm2104 cm² cm2105 m² m2106 km² Km2107 kg/l KG/L108 g/l G/L109 N N110 mN mN111 kN KN112 Nm Nm113 Nmm Nmm114 Nkm NKm115 µV/K µV/K
C002 Einheit des Messwertes
(nur wirksam, wenn Parameter C116 = 2siehe Seite 22)
X
Einheit LCD-Anzeige
21
5 Konfigurations- und Parametertabelle
Analogausgang
C114 Netzfrequenz / Temperatur-Kompensation X0 50Hz / interne Temperatur-Kompensation1 50Hz / feste Temperatur-Kompensation2 60Hz / interne Temperatur-Kompensation3 60Hz / feste Temperatur-Kompensation
Para-meter
Erklärung Werte-bereich
werkseitig X
C115 Wert bei fester Temperatur-Kompensation
0 … 100°C 0
C116 Messwert-Anzeige X0 Prozent1 wie Ausgangssignal (mA oder V)2 in konfigurierbarer Einheit
(siehe Parameter C002 Seite 18)
C211 Funktion des Analogausganges X0 0 … 20mA1 4 … 20mA2 0 … 10V3 2 … 10V
Eine Inversion der Grenzen können Sie durch Vertauschen der beiden Parameter SCL und SCH erzielen.
C212 Signal des Ausganges bei Fühlerbruch/-kurzschluss
X
0 positiv (22mA bzw. 11V - je nach C211)1 negativ (0mA bzw. 0V - je nach C211)
22
5 Konfigurations- und Parametertabelle
Binär-Ausgang 1
C221 Funktion des Binär-Ausganges 1 X0 ohne Funktion1 lk72 lk83 Fehlerausgang
Mehr Informationen zu lk7 und lk8 entnehmen Sie bitte
“Grenzwerte (Limitkomparatoren) einstellen” auf Seite 13.
C222 Signal des Binär-Ausganges 1 bei Fühlerbruch/-kurzschluss
X
0 aktiv1 inaktiv2 unverändert
Para-meter
Erklärung Werte-bereich
werkseitig X
C223 Schaltdifferenz unten(Hysterese)
0 … 250 100
Der Wertebereich entspricht 0 … 2,5%.
Para-meter
Erklärung Werte-bereich
werkseitig X
C224 Schaltdifferenz oben(Hysterese)
0 … 250 100
Der Wertebereich entspricht 0 … 2,5%.
23
5 Konfigurations- und Parametertabelle
Binär-Ausgang 2
C231 Funktion des Binär-Ausganges 2 X0 ohne Funktion1 lk72 lk83 Frequenzausgang
Mehr Informationen zu lk7 und lk8 entnehmen Sie bitte
“Grenzwerte (Limitkomparatoren) einstellen” auf Seite 13.
C232 Signal des Binär-Ausganges 2 bei Fühlerbruch/-kurzschluss
X
0 aktiv bzw. Frequenz C2361 inaktiv bzw. Frequenz C2352 unverändert
Para-meter
Erklärung Werte-bereich
werkseitig X
C233 Schaltdifferenz unten(Hysterese)
0 … 250 100
Der Wertebereich entspricht 0 … 2,5%.
Para-meter
Erklärung Werte-bereich
werkseitig X
C234 Schaltdifferenz oben(Hysterese)
0 … 250 100
Der Wertebereich entspricht 0 … 2,5%.
Para-meter
Erklärung Werte-bereich
werkseitig X
C235 Frequenz bei Messbereichsanfang
10 …1000Hz
10
24
5 Konfigurations- und Parametertabelle
Weiter Parameter
Para-meter
Erklärung Werte-bereich
werkseitig X
C236 Frequenz bei Messbereichsende
10 …1000Hz
1000
Para-meter
Erklärung Werte-bereich
werkseitig X
SCL Skalierung Startwert -1999 …+9999 Digit
0
SCh Skalierung Endwert -1999 …+9999 Digit
100
DF Filterzeitkonstante 0.0 …100.0s
0,6
R FE Gesamtwiderstandbei Widerstands-ferngebern
0 … 4000Ω 1000
C001 Simulation Istwertausgang
0 … 110%(111 = aus-geschaltet)
111
25
6 Hinweise ...
... zur Bedienung innerhalb der Parameter- und Konfigu-rationsebene
H Das Betätigen der Taste q als Bestätigung einer Werteinga-be setzt voraus, dass vorher ein Wert geändert wurde.
Ist dies nicht der Fall, wird die Betätigung als Aufruf desnächsten Parameters angesehen.
H Soll der Wert bei einer versehentlichen Änderung nicht über-nommen werden, ist der Timeout von 20s abzuwarten. DasGerät springt dann automatisch in den Normalbetrieb, ohnedie Änderung zu übernehmen.
H Überprüfen Sie alle eingegebenen Werte auf ihre Richtig-keit. Der Messumformer selbst überprüft keine Werteberei-che.
H Bitte beachten Sie, dass die Programmierung des Parame-ters „Teach In“ von der Standardbedienung abweicht.
v Siehe “Teach In” auf Seite 15.
H Damit die Parameter der Konfigurationsebene veränderbarsind, muss die Konfigurationseben aufgerufen werden,wenn in der Anzeige der Parameter OFFS steht. Ansonstenkönnen Sie die Parameter nur ablesen aber nicht verändern.
26
6 Hinweise ...
... allgemeiner Art
H Kann kein Parameter verändert werden, haben Sie vielleichtmit Hilfe des Setup-Programmes die Bedienung am Gerätverriegelt. Prüfen Sie die Einstellung durch das Setup-Pro-gramm.
Nur, wenn „Bedienerebene“, „Parameterebene“ und „Konfi-gurationsebene“ auf „Keine“ steht, können alle Einstellun-gen am Gerät geändert werden.
H Beide Ausgänge (Strom und Spannung) stehen immergleichzeitig zur Verfügung. Allerdings besitzt der Ausgang,der nicht aktiviert wurde, nur eine Genauigkeit von ca. ± 2%von der Spanne.
A Der Frequenz-Ausgang wird nicht angesteuert, solange die Setup-Schnittstelle aktiv ist.
27
7 PC-Setup-Programm
Mit dem als Typenzusatz erhältlichen PC-Setup-Programm lassensich alle Parameter des Messumformers (inkl. der kundenspezifi-schen Linearisierung) bequem ändern. Über die Setup-Schnittstellewerden der Messumformer und der PC über das „PC-Interface mitTTL/RS232-Umsetzer und Adapter“ miteinander verbunden.
Konfigurierbare Parameter:- TAG-Number (10 Zeichen)
- Analoger Eingang (Sensortyp)
- Anschlussart (2-/3-/4-Leiterschaltung)
- externe oder konstante Vergleichsstelle
- kundenspezifische Linearisierung
- Messbereichsgrenzen (Anfang und Ende)
- Ausgangssignal Strom/Spannung/Frequenz steigend/fallend
- digitales Filter
- Verhalten bei Fühlerbruch/-kurzschluss
- Nachkalibrierung/Feinabgleich
- Gerätekalibrierung
- Grenzwert/Hysterese der Limitkomparatoren
- Datei-Info-Text
Weitere Vorteile des PC-Setup-Programms- mehrere verschiedene Einstellungen verwalten
- eine Einstellung für mehrere Messumformer
- Einstellung zur Dokumentation ausdrucken
- Bedienung umschaltbar in den GMA-Standard
A Der Frequenz-Ausgang wird nicht angesteuert, solange die Setup-Schnittstelle aktiv ist.
28
8 Anschlussbeispiele
Beispiel 1 Anschluss einer SPS an den Open-Collector-Ausgang
Berechnungsbeispiel für RA (Arbeitswiderstand)
Bei dem Beispiel wird von folgenden typischen SPS-Kennwertenausgegangen:- für Signal „1“: 13 … 30V- für Signal „0“: -3 … +5V- Eingangsstrom für Signal „1“: 7mA
Bei einer angenommen Eingangsspannung von 18V/7mA für dasSignal „1“ ergibt sich folgende Berechnung:
Ergebnis: Gewählt wird ein Widerstand von 820 �.
RA24V - 18V
7mA-------------------------- 857,14 Ω= =
29
8 Anschlussbeispiele
Beispiel 2 Anschluss eines Relais an den Open-Collector-Ausgang
30
M. K. JUCHHEIM GmbH & CoHausadresse:Moltkestraße 13 - 31, 36039 Fulda, GermanyLieferadresse:Mackenrodtstraße 14, 36039 Fulda, GermanyPostadresse:36035 Fulda, GermanyTelefon: (06 61) 60 03-0Telefax: (06 61) 60 03-5 00E-Mail: [email protected]: www.jumo.de
JdTRANS T02 LCDprogrammable
transmitter
B 95.6522Operating Instructions
Overview of operation
1 Type designation
Standard accessory
- 1 Operating Instructions B 95.6522
Accessories
- PC setup program, multilingual
- PC interface cable with TTL/RS232 converter and adapter
JUMO dTRANS T02 LCD(1) Basic version
956522 programmable transmitter
(2) Input (programmable)x 888 factory-set (Pt100 DIN vl / 0 — 100°C)x 999 configuration to customer specification1
(3) Output (proportional DC current - programmable)x 888 factory-set (0 — 20mA)x 999 configuration to customer specification
(0/4 — 20mA or 0/2 — 10V)(4) Supply
x 22 20 — 53V AC/DC 48 — 63Hzx 23 110 — 240V AC +10/-15% 48 — 63Hz
(1) (2) (3) (4)Order code / - -Order example 956522 / 888 - 888 - 23
1 For configuration to customer specification,probe type and range have to be specified in plain text.
1
2 Installation
Connection diagram
Connection forSupply as per nameplate
Analog inputsThermocouple
Resistance thermometer / potentiometerin 2-wire circuit
RL ≤ 30Ω (RL = total lead resistance)Resistance thermometer / potentiometerin 3-wire circuit
Resistance thermometer / potentiometerin 4-wire circuit
2
2 Installation
Resistance transmitter in 3-wire circuit
Voltage input < 1V
Voltage input ≥ 1V
Current input
Analog outputsVoltage output
Current output
Digital outputsOpen-collector output 1
v See “Connection examples” on page 29.
Open-collector output 2
v See “Connection examples” on page 29.
Setup interface
A The setup interface and the analog out-put are not electrically isolated.v See “Setup interface” on page 5.
3
2 Installation
Installation notes
! The choice of cable, the installation and the electrical connec-tions must conform to the requirements of VDE 0100 “Regula-tions for the installation of power circuits with nominal voltagesbelow 1000V”, or the appropriate local regulations.
! The electrical connection, as well as work inside the unit, mustonly be carried out by qualified personnel.
! Ensure that the instrument is completely isolated from the sup-ply before carrying out work where live components may betouched.
! A current limiting resistor (safety function) interrupts the supplycircuit in the transmitter in the event of a short-circuit. The ex-ternal fusing of the supply voltage should not be rated above1A (slow).
! Avoid magnetic or electric fields, such as caused by transform-ers, mobile phones or electrostatic discharge in the vicinity of
the instrument1.
! Do not install inductive loads (relays, solenoid valves etc.) closeto the instrument. Use RC networks, spark quenchers or free-wheel diodes for interference suppression.
! Route input, output and supply cables separately, and not par-allel to each other. Run out and return cables next to each otherand twisted, if possible.
! All input and output lines that are not connected to the supplynetwork must be laid out as shielded and twisted cables (do notrun them in the vicinity of power cables or components). Theshielding must be grounded to the earth potential on the instru-ment side.
! Do not connect any additional loads to the supply terminals ofthe instrument.
4
2 Installation
Setup interface
! The instrument is not suitable for installation in areas with anexplosion hazard.
! Any electrical connection which deviates from the connectiondiagram may result in the destruction of the instrument.
! In supply networks that are subject to interference (e.g. thyristorcontrols), the instrument should be supplied via an isolatingtransformer.
! Supply fluctuations are only permissible within the specified
tolerances1.
1 see Data Sheet
A The setup interface and the analog output are not electrical-ly isolated. This means that under adverse conditions, witha built-in transmitter, equalizing currents may flow whenconnecting the PC interface. These equalizing currents mayresult in damage to the instruments connected.
No danger arises if the output circuit of the transmitter isisolated from ground. If it has not been assured that the out-put circuit on a built-in transmitter is electrically isolated,one of the following safety measures must be taken:
Use a PC without galvanic coupling to ground (e.g. a note-book in battery operation), or disconnect the output of thetransmitter before connecting the PC interface.
5
2 Installation
Dimensions
6
3 Displays and controls
Operational status at the operating level(normal operation)
Illumination/blink behavior
Limit comparator 1 inactive2 inactive
Limit comparator 1 active2 inactive
Limit comparator 1 inactive2 active
Limit comparator 1 active2 active
Overrange
buttons for operation
LCD displayinterface for PC setup program
LEDs for operational statusP = Power LEDS = Status LED
without significance, for internal purposes only
7
3 Displays and controls
Differentiation of the operational states
- in the Operating level status, the power LED is on permanently.
- in the Parameter level status, thepower LED blinks (equally on and off).
Operational status at the parameter level(programming mode)
Illumination/blink behavior
Limit forlimit comparator 1
Limit forlimit comparator 2
Fine calibration (zero)
Fine calibration (full scale)
Teach-in (0 % value)
8
4 Functions and operation
You can operate and program the transmitter by using the q, dand i buttons in conjunction with the LCD display and the blink cy-cles of the “Power” and “Status” LEDs, which have already beendescribed in Chapter 3 “Displays and controls”.
In use, three operating states can be distinguished:
- Operating level (normal operation)
- Parameter level (programming mode)
- Configuration level (programming mode)
Operating levelThe transmitter is at the operating level 2 seconds after power-on,or after leaving the parameter or configuration level.
Parameter levelFrom the operating level, you can access the parameter level bypressing the q button (for at least 2 seconds). The following func-tions can be programmed at this level:
- Limit value for limit comparator 1 AL1
- Limit value for limit comparator 2 AL2
- Fine calibration (zero point - 0%) OUTL
- Fine calibration (full scale - 100%) OUTH
- Teach-in OFFS
The parameter level is exited (quit)
- after editing the “Teach-in” parameter,
- if no button has been pressed for at least 20 seconds,
- or by pressing the button combination q + d.
The individual parameters can be altered, one after another. Youcan step from one parameter to the next by pressing the q button.
9
4 Functions and operation
Configuration levelYou can access the configuration level from the parameter level bypressing the q button (for at least 2 seconds).
The following functions can be programmed at this level:
- Probe type C111
- Linearization C112
- Number of decimal places C113
- Unit of measurement C002
- Supply frequency and temperature compensation C114
- Fixed value for temperature compensation C115
- Measurement display C116
- Function of the analog output C211
- Signal on probe break/short-circuit C212
- Function of the logic output 1 C221
- Signal on probe break/short-circuit C222
- Lower switching differential (hysteresis) C223
- Upper switching differential (hysteresis) C224
- Function of the logic output 2 C231
- Signal on probe break/short-circuit C232
- Lower switching differential (hysteresis) C233
- Upper switching differential (hysteresis) C234
H The parameters can only be modified when the parameterOFFS is active in the display and the configuration level hasbeen started. If another parameter is active, you can onlyread the current setting.
10
4 Functions and operation
- Frequency at the range start C235
- Frequency at the range end C236
- Start value for scaling SCL
- End value for scaling SCH
- Filter time DF
- Total resistance for resistance transmitter R FE
- Simulation of measurement output C001
The configuration level is exited (quit)
- after editing the last parameter,
- if no button has been pressed for at least 20 seconds,
- or by briefly pressing the button combination q + d.
The individual parameters can be altered, one after another. Youcan step from one parameter to the next by pressing the q button.
11
4 Functions and operation
Incrementing valuesWhen programming the parameters, the i button is used to in-crease a value (+).
Decrementing valuesWhen programming the parameters, the d button is used to de-crease a value (-).
Accepting valuesIf a setting has been altered, the q button has to be pressed to ac-cept the alteration.
q has a twofold function:
- Acceptance of altered values
- Calling the next parameter
Value check With the exception of the parameters OUTL, OUTH and OFFS, allpresent values can be checked during programming with the aid ofthe LCD display. A voltmeter can be used at the voltage output, asan additional check.
H If the parameter level is active, the analog output will not beoperated according to the input circuit connection whenprogramming the two limit values, but with the momentarylimit value.
H Please note that the programming of the “Teach-in” para-meter deviates from the standard operation.
v See “Teach-in” on page 15.
12
4 Functions and operation
Setting the limit values (limit comparators)You can alter the two limit values AL1 and AL2 by using the d and ibuttons. The momentary value will be produced via the output. Thevalue is accepted by pressing the q button.
The switching differential (hysteresis) can be set using the parame-ters C223 and C224 or C233 and C234.
Two functions are available for limit monitoring. With the help of theparameter C221 or C231, you can decide which one to use.
Function lk7:
Function lk8:
Of course, all parameters can also be set using the PC setup pro-gram, which is available as an extra code.
13
4 Functions and operation
Fine calibration (zero point and full scale)Fine calibration can be used to adjust the zero point and the slopeof the output signal. Here, too, the d and i buttons are availablefor altering the appropriate value, and for accepting it by pressingthe q button.
The converted value is produced at the output. At zero point (OUTL),this should correspond to the output signal 0%, at full scale (OUTH),to the output signal 100%.
The formula for calculating the new (converted) value is:
output (converted) value = measurement (input) valuescaled x full scale + zero point
14
4 Functions and operation
Teach-inThe “Teach-in” parameter serves to define the 0% value.
During programming, the zero point is produced at the output (e.g.4mA). This value is accepted by pressing the d or i button andexecuted with q. After a time-out without acceptance, the old valuewill be available again.
Example:
The position of a valve is detected by a potentiometer. The potenti-ometer covers the range 50 to 150Ω, with 50Ω corresponding to thevalve closed. The range is programmed as follows:
- Potentiometer 50 — 150 Ω
- Output 0 — 20mA
The following is assumed:
However, because of mechanical tolerances, the potentiometer po-sition with the valve closed is 52Ω, which results in an output cur-rent of 0.4mA. Thanks to the “Teach-in” function, this error can beeliminated as described below:
- Close valve
- Call the parameter level and select OFFS(0.4mA should then be present at the output).
- Press the d or i button – the output must nowchange to 0mA.
- Confirm alteration by pressing q.
- Exit the parameter level (either after a time-out of 20sec or bysimultaneously pressing q + d.
15
5 Configuration and parameter tables
You can record your settings in the configuration and parameter ta-bles below, in the position (column) marked with . The factorysettings are shown on a gray background ( ).
Parameters at the parameter level
Parameters at the configuration levelMeasurement input
Para-meter
Explanation Value range factorysetting
X
Al1 Limit value oflimit comparator 1
-1999 to+9999 digit
0
AL 2 Limit value oflimit comparator 2
-1999 to+9999 digit
0
OUTL Fine calibration 0%(zero)
see “Fine calibration (zero point and full scale)” on page 14
OTUH Fine calibration 100%(full scale)
see “Fine calibration (zero point and full scale)” on page 14
OFFS Teach-in see “Teach-in” on page 15
C111 Transducer X0 Resistance thermometer in 3-wire circuit1 Resistance thermometer in 4-wire circuit2 Resistance thermometer in 2-wire circuit3 Thermocouple4 Voltage up to 1000mV5 Voltage up to 10V6 Current7 Resistance transmitter8 Potentiometer 3-wire circuit9 Potentiometer 4-wire circuit
10 Potentiometer 2-wire circuit
16
5 Configuration and parameter tables
C112 Linearization X0 linear1 customized2 Pt 100 DIN3 Pt 500 DIN4 Pt 1000 DIN5 Pt 100 JIS6 Ni 1007 Ni 5008 Ni 10009 Type L
10 Type J11 Type U12 Type T13 Type K14 Type E15 Type N16 Type S17 Type R18 Type B19 Type D20 Type C
C113 Number of decimal places X0 no decimal place1 1 decimal place2 2 decimal places
17
5 Configuration and parameter tables
C002 Unit of measurement
(only effective if parameter C116 = 2see page 22
X
Unit LCD display0 °C °C1 °F °F2 K K34 bar BAR5 mbar mBAR6 Pa PA7 kPa KPA8 s SEC9 ms mSEC
10 min min11 h H12 d d13 100ms 100mS14 ml/s mL/S15 ml/min mL/mn16 l/s L/SEC17 l/min L/min18 l/h L/H19 m³/s m3/S20 m³/min m3/mn21 m³/h m3/H22 1/s 1/SEC23 1/min 1/min24 1/h 1/H25 Hz HZ26 kHz KHZ27 MHz MHZ28 lx LX
18
5 Configuration and parameter tables
29 mlx mLX30 klx KLX31 cd cd32 mcd mcd33 kcd Kcd34 µm µm35 mm mm36 cm cm37 m m38 km Km39 % %40 ‰ ‰41 ppm PPM42 ppb PPB43 µg µG44 mg mG45 g G46 kg KG47 t T48 µW µW49 mW mW50 W W51 kW KW52 MW MW53 mVA mVA54 VA VA55 kVA KVA56 mVAs mVAS57 VAs VAS
C002 Unit of measurement
(only effective if parameter C116 = 2see page 22
X
Unit LCD display
19
5 Configuration and parameter tables
58 kVAs KVAS59 J J60 µJ µJ61 mJ mJ62 kJ KJ63 Ws WS64 kWh KWH65 pH PH66 mΩ mOHM67 Ω OHM68 kΩ KOHM69 MΩ MOHM70 mm/s mm/S71 mm/h mm/H72 m/s m/SEC73 m/min m/MIN74 km/h Km/H75 %/s %/S76 m/s² m/S277 G G78 µl µL79 ml mL80 l L81 hl HL82 m³ M383 µV µV84 mV mV85 V V86 kV KV
C002 Unit of measurement
(only effective if parameter C116 = 2see page 22
X
Unit LCD display
20
5 Configuration and parameter tables
87 µA µA88 mA mA89 A A90 kA KA91 S S92 mS mS93 µS µS94 nH nH95 µH µH96 mH mH97 H H98 pF PF99 nF nF
100 µF µF101 mF mF102 F F103 mm² mm2104 cm² cm2105 m² m2106 km² Km2107 kg/l KG/L108 g/l G/L109 N N110 mN mN111 kN KN112 Nm Nm113 Nmm Nmm114 Nkm NKm115 µV/K µV/K
C002 Unit of measurement
(only effective if parameter C116 = 2see page 22
X
Unit LCD display
21
5 Configuration and parameter tables
Analog output
C114 Supply frequency/temperature compensation X0 50Hz / internal temperature compensation1 50Hz / fixed temperature compensation2 60Hz / internal temperature compensation3 60Hz / fixed temperature compensation
Para-meter
Explanation Value range factorysetting
X
C115 value with fixedtemperaturecompensation
0 — 100°C 0
C116 Measurement display X0 percent1 as output signal (mA or V)2 in configurable unit
(see parameter C002 page 18)
C211 Function of the analog output X0 0 — 20mA1 4 — 20mA2 0 — 10V3 2 — 10VThe limits can be inverted by swapping the two parameters
SCL and SCH.
C212 Signal of output onprobe break/short-circuit
X
0 positive (22mA or 11V - according to C211)1 negative (0mA or 0V - according to C211)
22
5 Configuration and parameter tables
Logic output 1
C221 Function of the logic output 1 X0 no function1 lk72 lk83 fault output
You will find additional information on lk7 and lk8 in “Setting the limit values (limit comparators)” on page 13.
C222 Signal of logic output 1 on probe break/short-circuit
X
0 active1 inactive2 unchanged
Para-meter
Explanation Value range factorysetting
X
C223 Lower switchingdifferential (hysteresis)
0 — 250 100
The value range corresponds to 0 — 2.5%.
Para-meter
Explanation Value range factorysetting
X
C224 Upper switchingdifferential (hysteresis)
0 — 250 100
The value range corresponds to 0 — 2.5%.
23
5 Configuration and parameter tables
Logic output 2
C231 Function of the logic output 2 X0 no function1 lk72 lk83 Frequency output
You will find additional information on lk7 and lk8 in“Setting the limit values (limit comparators)” on page 13.
C232 Signal of the logic output 2 onprobe break/short-circuit
X
0 active or frequency C2361 inactive or frequency C2352 unchanged
Para-meter
Explanation Value range factorysettting
X
C233 Lower switchingdifferential (hysteresis)
0 — 250 100
The value range corresponds to 0 — 2.5%.
Para-meter
Explanation Value range factorysetting
X
C234 Upper switchingdifferential (hysteresis)
0 — 250 100
The value range corresponds to 0 — 2.5%.
Para-meter
Explanation Value range factorysetting
X
C235 Frequency atrange start
10 —1000Hz
10
24
5 Configuration and parameter tables
Additional parameters
Para-meter
Explanation Value range factorysetting
X
C236 Frequency atrange end
10 —1000Hz
1000
Para-meter
Explanation Value range factorysetting
X
SCL Scaling start value -1999 to+9999 digit
0
SCh Scaling end value -1999 to+9999 digit
100
DF Filter time constant 0.0 —100.0sec
0.6
R FE Total resistance forresistance transmitters
0 — 4000Ω 1000
C001 Simulation ofmeasurement output
0 — 110%(111 =switched off)
111
25
6 Tips ...
... on operation within the parameter and configurationlevels
H Pressing the q button to confirm a value entry requires thata value has previously been modified.
If this is not the case, the confirmation will be interpreted asa call of the next parameter.
H If, after an accidental alteration, the value is not to be ac-cepted, just wait for the time-out of 20sec. Afterwards, theinstrument will automatically jump back to normal opera-tion, without accepting the alteration.
H Please check that all entered values are correct. The trans-mitter itself does not check value ranges.
H Please note that the programming of the “Teach-in” param-eter differs from the standard operation.
v See “Teach-in” on page 15.
H In order to be able to modify the parameters at the configu-ration level, the configuration level has to be called up whenthe display shows the parameter OFFS. If this is not the case,you can read the parameters, but you cannot modify them.
26
6 Tips ...
... of a more general nature
H If none of the parameters can be modified, then you mayhave locked the operation on the instrument through thesetup program. Please check the setting using the setupprogram.
The instrument settings can only be modified when “Oper-ating level”, “Parameter level” and “Configuration level” areset to “none”.
H Both outputs (current and voltage) are always available atthe same time. However, the output that has not been acti-vated only has an accuracy of approx. ± 2% of full scale.
A The frequency output will not be operated as long as thesetup interface is active.
Instrument operationInhibits:
Operating level: noneParameter level: noneConfiguration level: none
:
27
7 PC setup program
The PC setup program, which is available as an extra, can be usedto modify all parameters of the transmitter (including the custom lin-earization) with ease. Through the setup interface, the transmitterand the PC are linked via the “PC interface with TTL/RS232 con-verter and adapter”.
Configurable parameters- TAG number (10 characters)
- analog input (sensor type)
- connection circuit (2-/3-/4-wire circuit)
- external or constant cold junction
- custom linearization
- range limits (start and end)
- output signal current/voltage/frequency rising/falling
- digital filter
- response to probe break/short-circuit
- recalibration/fine calibration
- instrument calibration
- limit value/differential of the limit comparators
- file-info text
Additional benefits of the PC setup program- manage several settings
- one setting for several transmitters
- print out setting for documentation
- operation can be switched to GMA standard
A The frequency output will not be operated as long as thesetup interface is activated.
28
8 Connection examples
Example 1 Connecting a PLC to the open-collector output
Calculation example for RA (working resistance)
In this example, the following typical PLC characteristics are as-sumed:- for signal “1”: 13 — 30V- for signal “0”: -3 to +5V- input current for signal “1”: 7mA
An assumed input voltage of 18V/7mA for signal “1” results in thefollowing calculation:
Result: A resistance of 820 � will be selected.
RA24V - 18V
7mA-------------------------- 85.14 Ω= =
29
8 Connection examples
Example 2 Connecting a relay to the open-collector output
30
M. K. JUCHHEIM GmbH & CoStreet address:Moltkestraße 13 - 3136039 Fulda, GermanyDelivery address:Mackenrodtstraße 1436039 Fulda, GermanyPostal address:36035 Fulda, GermanyPhone: +49 (0) 661 60 03-0Fax: +49 (0) 661 60 03-5 00E-Mail: [email protected]:www.jumo.de
JUMO Instrument Co. Ltd.JUMO HouseTemple Bank, RiverwayHarlow, Essex CM20 2TT, UK
Phone: +44 (0) 1279 63 55 33Fax: +44 (0) 1279 63 52 62E-Mail: [email protected]
JUMO PROCESS CONTROL INC.735 Fox Chase,Coatesville, PA 19320, USAPhone: 610-380-8002
1-800-554-JUMOFax: 610-380-8009E-Mail: [email protected]:www.JumoUSA.com
Bedienübersicht1 TypenerklärungJUMO dTRANS T02 LCDSerienmäßiges ZubehörZubehör
2 InstallationAnschlussplanInstallationshinweiseSetup-SchnittstelleAbmessungen
3 Anzeige- und BedienelementeUnterscheidung der Betriebszustände
4 Funktionen und BedienungBedienerebeneParameterebeneKonfigurationsebeneWerte erhöhenWerte verringernWerte übernehmenWertkontrolleGrenzwerte (Limitkomparatoren) einstellenFeinabgleich (Nullpunkt und Endwert)Teach In
5 Konfigurations- und ParametertabelleParameter der ParameterebeneParameter der Konfigurationsebene
6 Hinweise ...... zur Bedienung innerhalb der Parameter- und Konfigurationsebene... allgemeiner Art
7 PC-Setup-ProgrammKonfigurierbare Parameter:Weitere Vorteile des PC-Setup-Programms
8 AnschlussbeispieleBeispiel 1 Anschluss einer SPS an den Open-Collector-AusgangBeispiel 2 Anschluss eines Relais an den Open-Collector-Ausgang
Overview of operation1 Type designationJUMO dTRANS T02 LCDStandard accessoryAccessories
2 InstallationConnection diagramInstallation notesSetup interfaceDimensions
3 Displays and controlsDifferentiation of the operational states
4 Functions and operationOperating levelParameter levelConfiguration levelIncrementing valuesDecrementing valuesAccepting valuesValue checkSetting the limit values (limit comparators)Fine calibration (zero point and full scale)Teach-in
5 Configuration and parameter tablesParameters at the parameter levelParameters at the configuration level
6 Tips ...... on operation within the parameter and configuration levels... of a more general nature
7 PC setup programConfigurable parametersAdditional benefits of the PC setup program
8 Connection examplesExample 1 Connecting a PLC to the open-collector outputExample 2 Connecting a relay to the open-collector output