A201 A202
ボー
ルね
じBall Scresw
標準
在庫
品
まえ
がき
Standard products in stock Outline
ボー
ルね
じBall Scresw
標準
在庫
品
まえ
がき
Standard products in stock Outline
標準在庫品Standard Products
KSSボールねじ標準在庫品は、以下の種類があります。これらの標準在庫品を利用すれば、短納期でお客様にお届けすることが可能です。
KSS has several varieties of standard products as follows. It is possible to make quick delivery to customers by using standard products.
SGシリーズ(精密ボールねじ) SG series(Precision Ball Screws)・ 固定側端末形状を標準化、支持側端末をフリーにして、標準ストロークを設定しています。・ 支持側端末が未加工のため、希望ストロークに合わせて追加工が可能です。・ C3(軸方向すきまゼロ)、C5(軸方向すきま5µm以下)の2種類があります。・ Configuration of fixed side end-journal is standardized, supported side end-journal
is free type and standard travel is set up. ・ Since supported side end-journal is unfinished, it is possible to do additional end
machining with your requested thread length. ・ There are C3(Axial play 0), C5(Axial play 5µm or less) available.
SRシリーズ(転造ボールねじ)/SSRシリーズ(ステンレス転造ボールねじ)SR series(Rolled Ball Screws)/SSR series(Stainless Rolled Ball Screws)・ ねじ溝転造加工による安価な製品を実現した在庫品です。・ 固定側、支持側とも軸端を未加工で在庫していますので、設計の自由度が広がります。・ Ct7(軸方向すきま20µm以下)、Ct10(軸方向すきま50µm以下)の2種類があります。・ ステンレス材の転造ボールねじ(SSRシリーズ)も標準在庫を保有しています。・ Standard and reasonable price products by Rolling formed process.・ Since fixed and supported side end-journal are unfinished, design flexibility is enlarged. ・ There are Ct7(Axial play 20µm or less), Ct10(Axial play 50µm or less) available.・ There are also Rolled Ball Screws made of stainless steel(SSR series) in stock.
SDシリーズ(精密開閉ボールねじ)SD series(Bi-directional Ball Screws)・ 1軸で左右開閉を可能にした経済的なボールねじです。・ 固定側、支持側とも軸端を未加工で在庫していますので、設計の自由度が広がります。・ C3(軸方向すきまゼロ)、C5(軸方向すきま5µm以下)の2種類があります。・ These are economical Ball Screws because a shaft has bi-directional thread.・ Since fixed and supported side end-journal are unfinished, design flexibility is enlarged. ・ There are C3(Axial play 0), C5(Axial play 5µm or less) available.
SRTシリーズ(つば付き転造ボールねじ)/SSRTシリーズ(つば付きステンレス転造ボールねじ)SRT series(Rolled Ball Screws with integrated end-journal)SSRT series(Stainless Rolled Ball Screws with integrated end-journal)・ 転造ボールねじの固定側軸端を太く設定し、未加工の状態で在庫を保有しています。・ 従来の転造ボールねじに比べ、更なる設計の自由度が広がりました。・ 軸端形状は、SGシリーズとの互換性を持った設計が可能になりました。・ ステンレス材のつば付き転造ボールねじ(SSRTシリーズ)も標準在庫を保有しています。・ Fixed side end-journal is set up bigger than Shaft nominal diameter and unfinished.・ More design flexibility compared to current Rolled Ball Screws.・ It is possible to design end-journal configuration compatible with SG series.・ There are also Integrated end-journal Rolled Ball Screws made of stainless steel(SSRT
series) in stock.
●精密ボールねじ Precision Ball Screws
●転造ボールねじ Rolled Ball Screws
SRT
SSRT
PSRシリーズ(精密転造ボールねじ)/PSRTシリーズ(つば付き精密転造ボールねじ)PSR series(Precision Rolled Ball Screws)PSRT series(Precision Rolled Ball Screws with integrated end-journal)・ 従来、Ct7、Ct10の並級しかできなかった転造加工で、精密級(JIS C5)を実現しました。・ 軸端未加工のPSRシリーズと軸端を太く設定したつば付き(PSRT)シリーズを在庫していますので、お客様の設計自由度は大きく広がります。・ 軸方向すきまは5µm以下に設定していますが、ご要望により軸方向すきまを無くす(予圧)ことも可能です。・ つば付きタイプは、固定側軸端が標準化されており、KSSサポートユニットがそのまま取り付けられます。・ KSS newly developed the high grade accuracy (JIS C5) Rolled Ball Screws, which
surpasses the conventional type of Ct7 or Ct10 grade.・ PSR series with unfinished end-journal and PSRT series with integrated end-journal are
in stock, so wide variety of design choices are available.・ The axial play is set at 5um or less, but zero backlash is possible by your request.・ For integrated type, fixed side end-journal is standardized and finished, KSS
Compact Support Unit can be installed.
●精密転造ボールねじ Precision Rolled Ball Screws
A203 A204
ボー
ルね
じBall Scresw
標準
在庫
品
まえ
がき
Standard products in stock Outline
ボー
ルね
じBall Scresw
標準
在庫
品
まえ
がき
Standard products in stock Outline
●軸端追加工KSSでは独自の追加工ノウハウにより、精度劣化のない軸端加工が可能です。軸端の追加工は、是非KSSにお任せください。以下に追加工の際の注意事項を記載いたします。
●Additional end-journal machiningTechnology of KSS end-journal machining enables to keep high accuracy of Ball Screws after re-works. Please ask for end-journal machining to us. Precautions of end-journal machining are as follows.
1)軸端の追加工はKSSで行うことをお奨めします。KSS以外で追加工を行う場合は、追加工後の精度保証はいたしかねますので、ご了承ください。
2)カタログ標準形状以外の追加工については、追加工指示図(ポンチ絵)とともに、ご指示くださるようお願いいたします。3)ナットの追加工は、行っておりませんので、フランジ形状等は、寸法表に合わせて設計するようにしてください。4) 潤滑ボールねじを使用する上で、潤滑剤の供給は必ず行ってください。KSS標準在庫品は、長期間の保管を前提とし、防錆油を塗布して真空包装しています。追加工ご依頼の際に、潤滑剤のご指定があれば、ご指定の潤滑剤をボールねじに塗布して納入いたします。なお、防錆油は潤滑剤ではありませんので、ご使用の際は白灯油等でボールねじを洗浄し、防錆油を除去後、ご使用の潤滑剤(グリースまたは潤滑油)を塗布してください。2~3ヶ月に1度、グリースの点検を行ってください。ご使用中にグリースが汚れてきた場合は、古いグリースを拭き取ったあとに給脂を行ってください。
5)ナットの自重落下ボールねじをすきま仕様でご使用の場合、ナットは自重で落下します。十分に注意してください。
6)お客様での追加工お客様での追加工は、精度保証外ですが、やむを得ず実施する場合は、上記の注意事項に加え以下の点に注意してください。
・ナット内への粉塵の侵入追加工の際にナット内に粉塵が侵入しないようにご注意ください。ねじ軸にナットを取りつけたまま追加工する場合は、ナットをビニール等で包み、両端をテープで密封するなど、確実に保護してください。・ナットの取り外しナットを取り外す場合は、図 A-21のように仮軸を使用してください。仮軸はご要望により付属いたします。仮軸でのナットの取り外し、再組み付けの際は、ボールとねじ溝がかみ合っていることを確認しながら、確実にゆっくりと行ってください。・追加工後の洗浄追加工後は、ボールねじに付着したごみ等を清浄な白灯油できれいに洗浄してください。・潤滑剤の塗布追加工後、ご使用前に潤滑剤の塗布を行ってください。・保管追加工後、長期間保管する場合は、防錆処理を確実に行ってください。
図 A-21 : 仮軸とナット取り外し
1)We recommend additional end-journal machining is done by KSS. We do not guarantee accuracy after re-works done by other than KSS.
2) When additional end-journal machining other than standard configuration in catalogue is requested, please send us drawing with end-journal profile on it.
3)Additional machining is not applied to the Nut. Please design flange configuration according to our dimension table.
4) Lubrication In Ball Screws use, lubricant should be applied on them. KSS Ball Screws are in vacuum wrapping with anti-rust oil due to purpose for long term stock. If you need specified lubricant, we will supply Ball Screws with lubricant you requested when requesting additional end-journal machining. Since anti-rust oil is not lubricant, anti-rust oil should be washed off from the Ball Screw with clean Kerosene and apply lubricant (Grease or lubricating oil). Please check the lubricant condition every 2 or 3months. If grease is contaminated, remove old grease, and replace with the new one.
5) Ball Nut falling by weight If Ball Screw is not preloaded, Ball Nut will fall down due to its own weight. Care must be taken.
6) Additional end-journal machining by customer Additional end-journal machining done by customer is out of our guarantee, but in case of unavoidably conducting, please take caution regarding above precautions as well as following points.
・ Invasion of dust inside Nut Care must be taken regarding invasion of dust inside Nut when additional end-journal machining. If additional end-journal machining is being done to the Shaft with Ball Nut, wrap the Nut with vinyl, sealing up both ends and surely protect it from dust.
・ Nut removal In case of Nut removal, please use dummy shaft shown in Fig. A-21. We can supply dummy shaft with products if you request. Make sure Balls and Screw Shaft groove are meshing correctly and remove the Nut slowly as well as re-assembling.
・ Cleaning after additional end-journal machining After additional end-journal machining, Ball Screws should be washed dust off with clean Kerosene.
・ Applying lubrication After additional end-journal machining, apply lubricant before using Ball Screw.
・ Storage After additional end-journal machining, surely conduct anti-rust treatment when Ball Screws are in long term stock.
Fig. A-21 : Dummy shaft and Nut removal
ナット
谷径-(0.1~0.2)
Shaft
Ball
Dummy shaft Nut
Root diameter
ねじ軸仮軸
ボール
ナット
谷径-(0.1~0.2)
Shaft
Ball
Dummy shaft Nut
Root diameter
ねじ軸仮軸
ボール
A207 A208
ボー
ルね
じBall Scresw
標準
在庫
品
SGシ
リー
ズStandard products in stock SG
series
ボー
ルね
じBall Scresw
標準
在庫
品
SGシ
リー
ズStandard products in stock SG
series
Unit(単位):mm
Ball Screw Modelボールねじ型番
Travelストローク
Grade精度
Shaft lengthねじ軸長さ
Lead accuracyリード精度 Total
Run-out全振れ
Axialplay
軸方向すきま
PreloadTorque予圧トルク
Nm
Basic Load Rating基本定格荷重 N
L1 L2 L3 L4
Travel deviation代表移動量誤差
ep
Variation変動Vu
Dynamic動定格荷重
Ca
Static静定格荷重
Coa
SG0300.5-038R070C3 25 C3 38 41 47 70 ±0.008 0.008 0.025 ~0.005 ― 150 220
Note)Please refer to page A206 for order code of end-journal machining. 注)追加工の呼び番号指定はぺージA206をご参照ください。
Unit(単位):mm
Ball Screw Specifications 諸元
Ball size ボール径 φ0.4
Number of thread 条数 1
Thread direction 巻方向 Right 右
Shaft root dia. ねじ軸谷径 φ2.6
Number of circuit 循環数 2.7×1
Shaft, Nut material軸、ナット材質 SCM415H
Surface hardnessねじ部表面硬度
HRC58~62(Thread area)
Anti-rust treatment防錆処理
Anti-rust oil防錆油
A04-SG0300.5
G0.008
A0.009
下表参照 G
Asee table below
φ8g
6-0
.005
-0.0
14
G
φ3
C0.3
C0.5
2.5
30°×0.3
11
(8) 3
A
E
0.0050.008
5 0-0.2
φ16
E
φ6h
8 0 -0
.018
φ4
-0.0
01-0
.006
φ3h
6 0 -0
.006
C0.3C0.3
M4×0.5
E0.004
(6)
(18) 5
6.5
R0.2max
23
(3)
L4
L3
L2
L1
2-φ2.4
PCD 12
8
A04-φ03journal
A-type B-type C-type
L5=L6-32
L6
A04-φ03journal
A-type B-type C-type
L5=L6-32
L6
Standard products in stock SG series標準在庫品 SGシリーズ
SG0300.5 Shaft dia.(軸径)φ3 Lead(リード)0.5mm C3
A-type A-type
Support-unit Recommendation推奨サポートユニット
Supported-side 支持側 : ─Fixed-side 固定側 : MSU-4C/4G
L5:Thread length after end-journal machining. 追加工後のねじ部長さL6:Total length after end-journal machining. 追加工後全長
Supported-side end-journal profile 支持側端末加工形状
Unit(単位):mm
Ball Screw Specifications 諸元
Ball size ボール径 φ0.6
Number of thread 条数 1
Thread direction 巻方向 Right 右
Shaft root dia. ねじ軸谷径 φ2.4
Number of circuit 循環数 3.7×1
Shaft, Nut material軸、ナット材質 SCM415H
Surface hardnessねじ部表面硬度
HRC58~62(Thread area)
Anti-rust treatment防錆処理
Anti-rust oil防錆油
A04-SG0301
A
G
A
下表参照 G
G
EA
E
0.005
see table below
0.008
E
0.008
0.009
0.004
φ6h
8 0 -0
.018
φ4
-0.0
01-0
.006
φ3h
6 0 -0
.006
C0.3C0.3
(3)
(6)
(18) 5
30°×0.3
6.5
R0.2max
M4×0.5
φ3
C0.3
L4
23L3
L2
L1
5 0-0.2
φ9g
6-0
.005
-0.0
14
PCD 14
11
2-φ2.9
14
(11) 3
φ19
C0.5
2.5
Standard products in stock SG series標準在庫品 SGシリーズ
SG0301 Shaft dia.(軸径)φ3 Lead(リード)1mm C3
Support-unit Recommendation推奨サポートユニット
Supported-side 支持側 : ─Fixed-side 固定側 : MSU-4C/4G
L5:Thread length after end-journal machining. 追加工後のねじ部長さL6:Total length after end-journal machining. 追加工後全長
Supported-side end-journal profile 支持側端末加工形状
Unit(単位):mm
Ball Screw Modelボールねじ型番
Travelストローク
Grade精度
Shaft lengthねじ軸長さ
Lead accuracyリード精度 Total
Run-out全振れ
Axialplay
軸方向すきま
PreloadTorque予圧トルク
Nm
Basic Load Rating基本定格荷重 N
L1 L2 L3 L4
Travel deviation代表移動量誤差
ep
Variation変動Vu
Dynamic動定格荷重
Ca
Static静定格荷重
Coa
SG0301-038R070C3 20 C3 38 41 47 70 ±0.008 0.008 0.025 ~0.005 ― 330 440
Note)Please refer to page A206 for order code of end-journal machining. 注)追加工の呼び番号指定はぺージA206をご参照ください。
D-type : Other than the above. 上記以外の形状 D-type : Other than the above. 上記以外の形状
A209 A210
ボー
ルね
じBall Scresw
標準
在庫
品
SGシ
リー
ズStandard products in stock SG
series
ボー
ルね
じBall Scresw
標準
在庫
品
SGシ
リー
ズStandard products in stock SG
series
Unit(単位):mm
Ball Screw Modelボールねじ型番
Travelストローク
Grade精度
Shaft lengthねじ軸長さ
Lead accuracyリード精度 Total
Run-out全振れ
Axialplay
軸方向すきま
PreloadTorque予圧トルク
Nm
Basic Load Rating基本定格荷重 N
L1 L2 L3 L4
Travel deviation代表移動量誤差
ep
Variation変動Vu
Dynamic動定格荷重
Ca
Static静定格荷重
Coa
SG0401-063R095C3 45 C3 63 66 72 95 ±0.008 0.008 0.025 0Spacer Ballスペーサボール(1:1)
~0.004 350 400SG0401-083R115C3 65 C3 83 86 92 115 ±0.008 0.008 0.025
SG0401-103R135C3 85 C3 103 106 112 135 ±0.010 0.008 0.035
SG0401-063R095C5 45 C5 63 66 72 95 ±0.018 0.018 0.035
~0.005 ― 560 790SG0401-083R115C5 65 C5 83 86 92 115 ±0.018 0.018 0.035
SG0401-103R135C5 85 C5 103 106 112 135 ±0.020 0.018 0.050
Note)Please refer to page A206 for order code of end-journal machining. 注)追加工の呼び番号指定はぺージA206をご参照ください。
Unit(単位):mm
Ball Screw Specifications 諸元
Ball size ボール径 φ0.8
Number of thread 条数 1
Thread direction 巻方向 Right 右
Shaft root dia. ねじ軸谷径 φ3.3
Number of circuit 循環数 3.7×1
Shaft, Nut material軸、ナット材質 SCM415H
Surface hardnessねじ部表面硬度
HRC58~62(Thread area)
Anti-rust treatment防錆処理
Anti-rust oil防錆油
A04-SG0401
E
A
G
A
下表参照 G
G
E
A
E
0.005
C5:0.010C3:0.008
C5:0.012C3:0.009
C5:0.010C3:0.008
C5:0.005C3:0.004
see table below
φ4
C0.3C0.3
(3) (18) 5
6.5
R0.2max
φ3h
6 0 -0
.006
φ6h
8 0 -0
.018
5 0 -0.2
2.5
φ4
-0.0
01-0
.006
30°×0.3
C0.3
L4
L1
M4×0.5
2-φ3.4
φ11
g6-0
.006
-0.0
17
PCD 17
13
φ23
17
(13) 4
C0.5
L2
L3 23
(6)
A04-φ04journal
A-type B-type C-type
R0.15max
7
R0.15max
L6
L6
L6
7
φ3-
0.00
2-
0.01
0
φ2.
7±
0.03
4.35±0.05
0.5+0.1 0
φ3-
0.00
2-
0.01
0
L5=L6-32
L5=L6-39
L5=L6-39
A04-φ04journal
A-type B-type C-type
R0.15max
7
R0.15max
L6
L6
L6
7
φ3-
0.00
2-
0.01
0
φ2.
7±
0.03
4.35±0.05
0.5+0.1 0
φ3-
0.00
2-
0.01
0
L5=L6-32
L5=L6-39
L5=L6-39
Standard products in stock SG series標準在庫品 SGシリーズ
SG0401 Shaft dia.(軸径)φ4 Lead(リード)1mm C3&C5
A-type A-type
Support-unit Recommendation推奨サポートユニット
Supported-side 支持側 : MSU-4CS/4GSFixed-side 固定側 : MSU-4C/4G
L5:Thread length after end-journal machining. 追加工後のねじ部長さL6:Total length after end-journal machining. 追加工後全長
B-type B-typeC-type C-type
Supported-side end-journal profile 支持側端末加工形状
Unit(単位):mm
Ball Screw Specifications 諸元
Ball size ボール径 φ0.8
Number of thread 条数 1
Thread direction 巻方向 Right 右
Shaft root dia. ねじ軸谷径 φ3.3
Number of circuit 循環数 2.7×1
Shaft, Nut material軸、ナット材質 SCM415H
Surface hardnessねじ部表面硬度
HRC58~62(Thread area)
Anti-rust treatment防錆処理
Anti-rust oil防錆油
A04-SG0402
E
A
G
A
下表参照 G
G
E
A
E
0.005
see table below
0.004
0.009
0.008
0.008
φ4
C0.3C0.3
(3) (18) 5
6.5
R0.2max
φ3h
6 0 -0
.006
φ6h
8 0 -0
.018
5 0 -0.2
2.5
φ4
-0.0
01-0
.006
30°×0.3
C0.3
L4
L1
M4×0.5
2-φ3.4
PCD 17
13
φ23
4
L2
L3 23
(6)
(15)
19
φ11
g6-0
.006
-0.0
17
C0.5
Standard products in stock SG series標準在庫品 SGシリーズ
SG0402 Shaft dia.(軸径)φ4 Lead(リード)2mm C3
Support-unit Recommendation推奨サポートユニット
Supported-side 支持側 : MSU-4CS/4GSFixed-side 固定側 : MSU-4C/4G
L5:Thread length after end-journal machining. 追加工後のねじ部長さL6:Total length after end-journal machining. 追加工後全長
Supported-side end-journal profile 支持側端末加工形状
Unit(単位):mm
Ball Screw Modelボールねじ型番
Travelストローク
Grade精度
Shaft lengthねじ軸長さ
Lead accuracyリード精度 Total
Run-out全振れ
Axialplay
軸方向すきま
PreloadTorque予圧トルク
Nm
Basic Load Rating基本定格荷重 N
L1 L2 L3 L4
Travel deviation代表移動量誤差
ep
Variation変動Vu
Dynamic動定格荷重
Ca
Static静定格荷重
Coa
SG0402-103R135C3 80 C3 103 106 112 135 ±0.010 0.008 0.035 ~0.005 ― 420 570
Note)Please refer to page A206 for order code of end-journal machining. 注)追加工の呼び番号指定はぺージA206をご参照ください。
D-type : Other than the above. 上記以外の形状 D-type : Other than the above. 上記以外の形状
A211 A212
ボー
ルね
じBall Scresw
標準
在庫
品
SGシ
リー
ズStandard products in stock SG
series
ボー
ルね
じBall Scresw
標準
在庫
品
SGシ
リー
ズStandard products in stock SG
series
Unit(単位):mm
Ball Screw Modelボールねじ型番
Travelストローク
Grade精度
Shaft lengthねじ軸長さ
Lead accuracyリード精度 Total
Run-out全振れ
Axialplay
軸方向すきま
PreloadTorque予圧トルク
Nm
Basic Load Rating基本定格荷重 N
L1 L2 L3 L4
Travel deviation代表移動量誤差
ep
Variation変動Vu
Dynamic動定格荷重
Ca
Static静定格荷重
Coa
SG0504-062R095C3 40 C3 62 66 72 95 ±0.008 0.008 0.025 0Spacer Ballスペーサボール(1:1)
~0.005 300 360SG0504-112R145C3 90 C3 112 116 122 145 ±0.010 0.008 0.035
SG0504-062R095C5 40 C5 62 66 72 95 ±0.018 0.018 0.035~0.005 ― 470 720
SG0504-112R145C5 90 C5 112 116 122 145 ±0.020 0.018 0.050
Note)Please refer to page A206 for order code of end-journal machining. 注)追加工の呼び番号指定はぺージA206をご参照ください。
Unit(単位):mm
Ball Screw Specifications 諸元
Ball size ボール径 φ0.8
Number of thread 条数 1
Thread direction 巻方向 Right 右
Shaft root dia. ねじ軸谷径 φ4.3
Number of circuit 循環数 2.7×1
Shaft, Nut material軸、ナット材質 SCM415H
Surface hardnessねじ部表面硬度
HRC58~62(Thread area)
Anti-rust treatment防錆処理
Anti-rust oil防錆油
E
下表参照 G E0.005
C5:0.010C3:0.008
C5:0.012C3:0.009
C5:0.010C3:0.008
C5:0.005C3:0.004
see table below
A
G
A
G
A
E
C0.3C0.3
23
(6)
(18) 5
6.5
R0.2max
φ3h
6 0 -0
.006
φ6h
8 0 -0
.018
5 0 -0.2
2.5
φ4
-0.0
01-0
.006
30°×0.3
M4×0.5
C0.3
4
φ12
g6-0
.006
-0.0
17
22
φ24
(4)
C0.5
PCD 18
2-φ3.4
14
φ5
L4
L3
L2
L1
(18)
A04-SG0504
Standard products in stock SG series標準在庫品 SGシリーズ
SG0504 Shaft dia.(軸径)φ5 Lead(リード)4mm C3&C5
Support-unit Recommendation推奨サポートユニット
Supported-side 支持側 : MSU-4CS/4GSFixed-side 固定側 : MSU-4C/4G
L5:Thread length after end-journal machining. 追加工後のねじ部長さL6:Total length after end-journal machining. 追加工後全長
Supported-side end-journal profile 支持側端末加工形状
Unit(単位):mm
Ball Screw Modelボールねじ型番
Travelストローク
Grade精度
Shaft lengthねじ軸長さ
Lead accuracyリード精度 Total
Run-out全振れ
Axialplay
軸方向すきま
PreloadTorque予圧トルク
Nm
Basic Load Rating基本定格荷重 N
L1 L2 L3 L4
Travel deviation代表移動量誤差
ep
Variation変動Vu
Dynamic動定格荷重
Ca
Static静定格荷重
Coa
SG0601-085R120C3 65 C3 85 88 95 120 ±0.008 0.008 0.025 0Spacer Ballスペーサボール(1:1)
~0.006 430 610SG0601-110R145C3 90 C3 110 113 120 145 ±0.010 0.008 0.035
SG0601-135R170C3 115 C3 135 138 145 170 ±0.010 0.008 0.035
SG0601-085R120C5 65 C5 85 88 95 120 ±0.018 0.018 0.035
~0.005 ー 680 1200SG0601-110R145C5 90 C5 110 113 120 145 ±0.020 0.018 0.050
SG0601-135R170C5 115 C5 135 138 145 170 ±0.020 0.018 0.050
Note)Please refer to page A206 for order code of end-journal machining. 注)追加工の呼び番号指定はぺージA206をご参照ください。
Unit(単位):mm
Ball Screw Specifications 諸元
Ball size ボール径 φ0.8
Number of thread 条数 1
Thread direction 巻方向 Right 右
Shaft root dia. ねじ軸谷径 φ5.3
Number of circuit 循環数 3.7×1
Shaft, Nut material軸、ナット材質 SCM415H
Surface hardnessねじ部表面硬度
HRC58~62(Thread area)
Anti-rust treatment防錆処理
Anti-rust oil防錆油
A04-SG0601
E
下表参照 G E0.005
C5:0.010C3:0.008
C5:0.012C3:0.009
C5:0.010C3:0.008
C5:0.005C3:0.004
see table below
A
G
A
G
A
E
φ8h
8 0 -0
.022
φ5
-0.0
01-0
.006
φ4h
6 0 -0
.008
L4
25
(7)
(19) 6
6.5
C0.3C0.3
M5×0.5
30°×0.3
R0.2max
3
φ6
7 0-0.2
L3
L2
(3)
L1
φ13
g6-0
.006
-0.0
17
15
PCD 21.5
17
4
C0.5
2-φ3.4
φ28
(13)
C0.3
Standard products in stock SG series標準在庫品 SGシリーズ
SG0601 Shaft dia.(軸径)φ6 Lead(リード)1mm C3&C5
Support-unit Recommendation推奨サポートユニット
Supported-side 支持側 : MSU-5CS/5GSFixed-side 固定側 : MSU-5C/5G
L5:Thread length after end-journal machining. 追加工後のねじ部長さL6:Total length after end-journal machining. 追加工後全長
Supported-side end-journal profile 支持側端末加工形状
A04-φ04journal
A-type B-type C-type
R0.15max
7
R0.15max
L6
L6
L6
7
φ3-
0.00
2-
0.01
0
φ2.
7±
0.03
4.35±0.05
0.5+0.1 0
φ3-
0.00
2-
0.01
0
L5=L6-33
L5=L6-40
L5=L6-40
A-type B-type C-type
A04-φ06journal
A-type B-type C-type
R0.2max
8
R0.2max
L6
L6
L6
8
φ4-
0.00
2-
0.01
0
φ3.
7±
0.03
φ4-
0.00
2-
0.01
0
5.35 ±0.05
0.5+0.1 0
L5=L6-35
L5=L6-43
L5=L6-43
A-type B-type C-type
D-type : Other than the above. 上記以外の形状 D-type : Other than the above. 上記以外の形状
A213 A214
ボー
ルね
じBall Scresw
標準
在庫
品
SGシ
リー
ズStandard products in stock SG
series
ボー
ルね
じBall Scresw
標準
在庫
品
SGシ
リー
ズStandard products in stock SG
series
Unit(単位):mm
Ball Screw Specifications 諸元
Ball size ボール径 φ1.0
Number of thread 条数 1
Thread direction 巻方向 Right 右
Shaft root dia. ねじ軸谷径 φ5.1
Number of circuit 循環数 2.7×1
Shaft, Nut material軸、ナット材質 SCM415H
Surface hardnessねじ部表面硬度
HRC58~62(Thread area)
Anti-rust treatment防錆処理
Anti-rust oil防錆油
A04-SG0602
E
下表参照 G E0.005
C5:0.010C3:0.008
C5:0.012C3:0.009
C5:0.010C3:0.008
C5:0.005C3:0.004
see table below
A
G
A
G
A
E
φ8h
8 0 -0
.022
φ5
-0.0
01-0
.006
φ4h
6 0 -0
.008
L4
25
(7)
(19) 6
6.5
C0.3C0.3
M5×0.5
30°×0.5
R0.2max
3
φ6
7 0-0.2
L3
L2
C0.5
(3)
L1
φ29φ
15g6
-0.0
06-0
.017
C0.5
17
(13) 4
PCD 23
2-φ3.4
17
Standard products in stock SG series標準在庫品 SGシリーズ
SG0602 Shaft dia.(軸径)φ6 Lead(リード)2mm C3&C5
Support-unit Recommendation推奨サポートユニット
Supported-side 支持側 : MSU-5CS/5GSFixed-side 固定側 : MSU-5C/5G
L5:Thread length after end-journal machining. 追加工後のねじ部長さL6:Total length after end-journal machining. 追加工後全長
Supported-side end-journal profile 支持側端末加工形状
Unit(単位):mm
Ball Screw Modelボールねじ型番
Travelストローク
Grade精度
Shaft lengthねじ軸長さ
Lead accuracyリード精度 Total
Run-out全振れ
Axialplay
軸方向すきま
PreloadTorque予圧トルク
Nm
Basic Load Rating基本定格荷重 N
L1 L2 L3 L4
Travel deviation代表移動量誤差
ep
Variation変動Vu
Dynamic動定格荷重
Ca
Static静定格荷重
Coa
SG0602-085R120C3 65 C3 85 88 95 120 ±0.008 0.008 0.025 0Spacer Ballスペーサボール(1:1)
0.003~0.007 470 590
SG0602-135R170C3 115 C3 135 138 145 170 ±0.010 0.008 0.035
SG0602-085R120C5 65 C5 85 88 95 120 ±0.018 0.018 0.035~0.005 ― 750 1200
SG0602-135R170C5 115 C5 135 138 145 170 ±0.020 0.018 0.050
Note)Please refer to page A206 for order code of end-journal machining. 注)追加工の呼び番号指定はぺージA206をご参照ください。
Unit(単位):mm
Ball Screw Specifications 諸元
Ball size ボール径 φ1.0
Number of thread 条数 1
Thread direction 巻方向 Right 右
Shaft root dia. ねじ軸谷径 φ5.1
Number of circuit 循環数 2.7×1
Shaft, Nut material軸、ナット材質 SCM415H
Surface hardnessねじ部表面硬度
HRC58~62(Thread area)
Anti-rust treatment防錆処理
Anti-rust oil防錆油
A04-SG0602.5
E
下表参照 G E0.005
C5:0.010C3:0.008
C5:0.012C3:0.009
C5:0.010C3:0.008
C5:0.005C3:0.004
see table below
A
G
A
G
A
E
φ8h
8 0 -0
.022
φ5
-0.0
01-0
.006
φ4h
6 0 -0
.008
25
(7)
(19) 6
6.5
C0.3C0.3
M5×0.5
30°×0.5
R0.2max
3
φ6
7 0-0.2
C0.5
(3)
PCD 23
2-φ3.4
17
φ29φ
15g6
-0.0
06-0
.017
18
C0.5
4(14)
L4
L3
L2
L1
Standard products in stock SG series標準在庫品 SGシリーズ
SG0602.5 Shaft dia.(軸径)φ6 Lead(リード)2.5mm C3&C5
Support-unit Recommendation推奨サポートユニット
Supported-side 支持側 : MSU-5CS/5GSFixed-side 固定側 : MSU-5C/5G
L5:Thread length after end-journal machining. 追加工後のねじ部長さL6:Total length after end-journal machining. 追加工後全長
Supported-side end-journal profile 支持側端末加工形状
Unit(単位):mm
Ball Screw Modelボールねじ型番
Travelストローク
Grade精度
Shaft lengthねじ軸長さ
Lead accuracyリード精度 Total
Run-out全振れ
Axialplay
軸方向すきま
PreloadTorque予圧トルク
Nm
Basic Load Rating基本定格荷重 N
L1 L2 L3 L4
Travel deviation代表移動量誤差
ep
Variation変動Vu
Dynamic動定格荷重
Ca
Static静定格荷重
Coa
SG0602.5-085R120C3 65 C3 85 88 95 120 ±0.008 0.008 0.025 0Spacer Ballスペーサボール(1:1)
0.003~0.007 470 590
SG0602.5-135R170C3 115 C3 135 138 145 170 ±0.010 0.008 0.035
SG0602.5-085R120C5 65 C5 85 88 95 120 ±0.018 0.018 0.035~0.005 ― 750 1200
SG0602.5-135R170C5 115 C5 135 138 145 170 ±0.020 0.018 0.050
Note)Please refer to page A206 for order code of end-journal machining. 注)追加工の呼び番号指定はぺージA206をご参照ください。
A04-φ06journal
A-type B-type C-type
R0.2max
8
R0.2max
L6
L6
L6
8
φ4-
0.00
2-
0.01
0
φ3.
7±
0.03
φ4-
0.00
2-
0.01
0
5.35 ±0.05
0.5+0.1 0
L5=L6-35
L5=L6-43
L5=L6-43
A-type B-type C-type
A04-φ06journal
A-type B-type C-type
R0.2max
8
R0.2max
L6
L6
L6
8
φ4-
0.00
2-
0.01
0
φ3.
7±
0.03
φ4-
0.00
2-
0.01
0
5.35 ±0.05
0.5+0.1 0
L5=L6-35
L5=L6-43
L5=L6-43
A-type B-type C-type
D-type : Other than the above. 上記以外の形状 D-type : Other than the above. 上記以外の形状
A215 A216
ボー
ルね
じBall Scresw
標準
在庫
品
SGシ
リー
ズStandard products in stock SG
series
ボー
ルね
じBall Scresw
標準
在庫
品
SGシ
リー
ズStandard products in stock SG
series
Unit(単位):mm
Ball Screw Modelボールねじ型番
Travelストローク
Grade精度
Shaft lengthねじ軸長さ
Lead accuracyリード精度 Total
Run-out全振れ
Axialplay
軸方向すきま
PreloadTorque予圧トルク
Nm
Basic Load Rating基本定格荷重 N
L1 L2 L3 L4
Travel deviation代表移動量誤差
ep
Variation変動Vu
Dynamic動定格荷重
Ca
Static静定格荷重
Coa
SG0606-084R120C5 65 C5 84 88 95 120 ±0.018 0.018 0.035~0.005 ― 870 1450
SG0606-134R170C5 115 C5 134 138 145 170 ±0.020 0.018 0.050
Note)Please refer to page A206 for order code of end-journal machining. 注)追加工の呼び番号指定はぺージA206をご参照ください。
Unit(単位):mm
Ball Screw Specifications 諸元
Ball size ボール径 φ1.0
Number of thread 条数 2
Thread direction 巻方向 Right 右
Shaft root dia. ねじ軸谷径 φ5.2
Number of circuit 循環数 1.6×2
Shaft, Nut material軸、ナット材質 SCM415H
Surface hardnessねじ部表面硬度
HRC58~62(Thread area)
Anti-rust treatment防錆処理
Anti-rust oil防錆油
Standard products in stock SG series標準在庫品 SGシリーズ
SG0606 Shaft dia.(軸径)φ6 Lead(リード)6mm C5
Support-unit Recommendation推奨サポートユニット
Supported-side 支持側 : MSU-5CS/5GSFixed-side 固定側 : MSU-5C/5G
L5:Thread length after end-journal machining. 追加工後のねじ部長さL6:Total length after end-journal machining. 追加工後全長
Supported-side end-journal profile 支持側端末加工形状
Unit(単位):mm
Ball Screw Specifications 諸元
Ball size ボール径 φ1.2
Number of thread 条数 2
Thread direction 巻方向 Right 右
Shaft root dia. ねじ軸谷径 φ5.0
Number of circuit 循環数 1.2×2
Shaft, Nut material軸、ナット材質 SCM415H
Surface hardnessねじ部表面硬度
HRC58~62(Thread area)
Anti-rust treatment防錆処理
Anti-rust oil防錆油
A04-SG0610
下表参照 G E0.005
see table below
0.005 E
A
G
0.012
0.010
A
G
A
E
0.010
30°
4-φ3.4
PCD 21
16
30°
φ8h
8 0 -0
.022
φ5
-0.0
01-0
.006
φ4h
6 0 -0
.008
25
(7)
(19) 6
6.5
C0.3C0.3
M5×0.5
30°×0.5
R0.2max
3
φ6
7 0-0.2
φ14
g6-0
.006
-0.0
17
φ27
4
C0.5
23
(11.5)
5
L4
L3
L2
L1
Standard products in stock SG series標準在庫品 SGシリーズ
SG0610 Shaft dia.(軸径)φ6 Lead(リード)10mm C5
Support-unit Recommendation推奨サポートユニット
Supported-side 支持側 : MSU-5CS/5GSFixed-side 固定側 : MSU-5C/5G
L5:Thread length after end-journal machining. 追加工後のねじ部長さL6:Total length after end-journal machining. 追加工後全長
Supported-side end-journal profile 支持側端末加工形状
Unit(単位):mm
Ball Screw Modelボールねじ型番
Travelストローク
Grade精度
Shaft lengthねじ軸長さ
Lead accuracyリード精度 Total
Run-out全振れ
Axialplay
軸方向すきま
PreloadTorque予圧トルク
Nm
Basic Load Rating基本定格荷重 N
L1 L2 L3 L4
Travel deviation代表移動量誤差
ep
Variation変動Vu
Dynamic動定格荷重
Ca
Static静定格荷重
Coa
SG0610-133R170C5 110 C5 133 138 145 170 ±0.020 0.018 0.050 ~0.005 ― 950 1600
Note)Please refer to page A206 for order code of end-journal machining. 注)追加工の呼び番号指定はぺージA206をご参照ください。
下表参照 G E0.005
A04-SG0606
see table below
0.005 E
A
G
0.012
0.010
A
G
A
E
0.010
30°
4-φ3.4
PCD 21
16
30°
φ8h
8 0 -0
.022
φ5
-0.0
01-0
.006
φ4h
6 0 -0
.008
25
(7)
(19) 6
6.5
C0.3C0.3
M5×0.5
30°×0.5
R0.2max
3
φ6
7 0-0.2
φ14
g6-0
.006
-0.0
17
φ27
17
4(8)
(4)
C0.5
L4
L3
L2
L1
A04-φ06journal
A-type B-type C-type
R0.2max
8
R0.2max
L6
L6
L6
8
φ4-
0.00
2-
0.01
0
φ3.
7±
0.03
φ4-
0.00
2-
0.01
0
5.35 ±0.05
0.5+0.1 0
L5=L6-36
L5=L6-44
L5=L6-44
A-type B-type C-type
A04-φ06journal
A-type B-type C-type
R0.2max
8
R0.2max
L6
L6
L6
8
φ4-
0.00
2-
0.01
0
φ3.
7±
0.03
φ4-
0.00
2-
0.01
0
5.35 ±0.05
0.5+0.1 0
L5=L6-37
L5=L6-45
L5=L6-45
A-type B-type C-type
D-type : Other than the above. 上記以外の形状 D-type : Other than the above. 上記以外の形状
A217 A218
ボー
ルね
じBall Scresw
標準
在庫
品
SGシ
リー
ズStandard products in stock SG
series
ボー
ルね
じBall Scresw
標準
在庫
品
SGシ
リー
ズStandard products in stock SG
series
Unit(単位):mm
Ball Screw Specifications 諸元
Ball size ボール径 φ0.8
Number of thread 条数 1
Thread direction 巻方向 Right 右
Shaft root dia. ねじ軸谷径 φ7.3
Number of circuit 循環数 3.7×1
Shaft, Nut material軸、ナット材質 SCM415H
Surface hardnessねじ部表面硬度
HRC58~62(Thread area)
Anti-rust treatment防錆処理
Anti-rust oil防錆油
A04-SG0801
E
下表参照 G
E0.005
C5:0.010C3:0.008
C5:0.012C3:0.009
C5:0.010C3:0.008
C5:0.005C3:0.004
see table below
A
G
G
A
E
A
φ4.
5h6
0 -0.0
08
φ6
-0.0
01-0
.006
30
(7)
(22.5) 7.5
7φ
9.5h
8 0 -0
.022
C0.3C0.5
M6×0.75
30°×0.5
φ8
8 0-0.2
R0.2max
3
φ16
g6-0
.006
-0.0
17
(13) 4
18
PCD 24
17
C0.5
2-φ3.4
φ30
(3)
C0.3
L4
L3
L2
L1
Standard products in stock SG series標準在庫品 SGシリーズ
SG0801 Shaft dia.(軸径)φ8 Lead(リード)1mm C3&C5
Support-unit Recommendation推奨サポートユニット
Supported-side 支持側 : MSU-6CS/6GSFixed-side 固定側 : MSU-6C/6G
L5:Thread length after end-journal machining. 追加工後のねじ部長さL6:Total length after end-journal machining. 追加工後全長
Supported-side end-journal profile 支持側端末加工形状
Unit(単位):mm
Ball Screw Modelボールねじ型番
Travelストローク
Grade精度
Shaft lengthねじ軸長さ
Lead accuracyリード精度 Total
Run-out全振れ
Axialplay
軸方向すきま
PreloadTorque予圧トルク
Nm
Basic Load Rating基本定格荷重 N
L1 L2 L3 L4
Travel deviation代表移動量誤差
ep
Variation変動Vu
Dynamic動定格荷重
Ca
Static静定格荷重
Coa
SG0801-100R140C3 80 C3 100 103 110 140 ±0.008 0.008 0.035
0Spacer Ballスペーサボール(1:1)
0.002~0.008 490 820
SG0801-130R170C3 110 C3 130 133 140 170 ±0.010 0.008 0.035
SG0801-160R200C3 140 C3 160 163 170 200 ±0.010 0.008 0.035
SG0801-210R250C3 190 C3 210 213 220 250 ±0.012 0.008 0.050
SG0801-100R140C5 80 C5 100 103 110 140 ±0.018 0.018 0.050
~0.005 ー 780 1650SG0801-130R170C5 110 C5 130 133 140 170 ±0.020 0.018 0.050
SG0801-160R200C5 140 C5 160 163 170 200 ±0.020 0.018 0.050
SG0801-210R250C5 190 C5 210 213 220 250 ±0.023 0.018 0.065
Note)Please refer to page A206 for order code of end-journal machining. 注)追加工の呼び番号指定はぺージA206をご参照ください。
Unit(単位):mm
Ball Screw Specifications 諸元
Ball size ボール径 φ1.5875
Number of thread 条数 1
Thread direction 巻方向 Right 右
Shaft root dia. ねじ軸谷径 φ6.6
Number of circuit 循環数 3.7×1
Shaft, Nut material軸、ナット材質 SCM415H
Surface hardnessねじ部表面硬度
HRC58~62(Thread area)
Anti-rust treatment防錆処理
Anti-rust oil防錆油
A04-SG0802
E
下表参照 G
E0.005
C5:0.010C3:0.008
C5:0.012C3:0.009
C5:0.010C3:0.008
C5:0.005C3:0.004
see table below
A
G
G
A
E
A
φ4.
5h6
0 -0.0
08
φ6
-0.0
01-0
.006
30
(7)
(22.5) 7.5
7
φ9.
5h8
0 -0.0
22
C0.3C0.5
M6×0.75
30°×0.5
φ8
8 0-0.2
R0.2max
3
C0.5
(4)
φ20
g6-0
.007
-0.0
20
22
PCD 30
24
5
C0.5
(19) 2-φ4.5
φ38
L4
L3
L2
L1
Standard products in stock SG series標準在庫品 SGシリーズ
SG0802 Shaft dia.(軸径)φ8 Lead(リード)2mm C3&C5
Support-unit Recommendation推奨サポートユニット
Supported-side 支持側 : MSU-6CS/6GSFixed-side 固定側 : MSU-6C/6G
L5:Thread length after end-journal machining. 追加工後のねじ部長さL6:Total length after end-journal machining. 追加工後全長
Supported-side end-journal profile 支持側端末加工形状
Unit(単位):mm
Ball Screw Modelボールねじ型番
Travelストローク
Grade精度
Shaft lengthねじ軸長さ
Lead accuracyリード精度 Total
Run-out全振れ
Axialplay
軸方向すきま
PreloadTorque予圧トルク
Nm
Basic Load Rating基本定格荷重 N
L1 L2 L3 L4
Travel deviation代表移動量誤差
ep
Variation変動Vu
Dynamic動定格荷重
Ca
Static静定格荷重
Coa
SG0802-099R140C3 75 C3 99 103 110 140 ±0.008 0.008 0.035
0Spacer Ballスペーサボール(1:1)
0.004~0.020 1550 2100
SG0802-129R170C3 105 C3 129 133 140 170 ±0.010 0.008 0.035
SG0802-159R200C3 135 C3 159 163 170 200 ±0.010 0.008 0.035
SG0802-209R250C3 185 C3 209 213 220 250 ±0.012 0.008 0.050
SG0802-099R140C5 75 C5 99 103 110 140 ±0.018 0.018 0.050
~0.005 ー 2400 4100SG0802-129R170C5 105 C5 129 133 140 170 ±0.020 0.018 0.050
SG0802-159R200C5 135 C5 159 163 170 200 ±0.020 0.018 0.050
SG0802-209R250C5 185 C5 209 213 220 250 ±0.023 0.018 0.065
Note)Please refer to page A206 for order code of end-journal machining. 注)追加工の呼び番号指定はぺージA206をご参照ください。
A04-φ08journal
A-type B-type C-type
6.8 +0.1 0
0.8 +0.1 0
φ5.
7 0 -0.
06
φ6-
0.00
2-
0.01
0
R0.2max
9
L6
L6
L5=L6-40
L5=L6-49
L5=L6-49
φ6-
0.00
2-
0.01
0
R0.2max 9
L6
A-type B-type C-type
A04-φ08journal
A-type B-type C-type
6.8 +0.1 0
0.8 +0.1 0
φ5.
7 0 -0.
06
φ6-
0.00
2-
0.01
0
R0.2max
9
L6
L6
L5=L6-41
L5=L6-50
L5=L6-50
φ6-
0.00
2-
0.01
0
R0.2max 9
L6
A-type B-type C-type
D-type : Other than the above. 上記以外の形状 D-type : Other than the above. 上記以外の形状
A219 A220
ボー
ルね
じBall Scresw
標準
在庫
品
SGシ
リー
ズStandard products in stock SG
series
ボー
ルね
じBall Scresw
標準
在庫
品
SGシ
リー
ズStandard products in stock SG
series
Unit(単位):mm
Ball Screw Specifications 諸元
Ball size ボール径 φ1.5875
Number of thread 条数 1
Thread direction 巻方向 Right 右
Shaft root dia. ねじ軸谷径 φ6.3
Number of circuit 循環数 2.7×1
Shaft, Nut material軸、ナット材質 SCM415H
Surface hardnessねじ部表面硬度
HRC58~62(Thread area)
Anti-rust treatment防錆処理
Anti-rust oil防錆油
A04-SG0802.5
E
下表参照 G
E0.005
see table below
A
G
G
A
E
A
0.010
0.005
0.012
0.010
φ4.
5h6
0 -0.0
08
φ6
-0.0
01-0
.006
30
(7)
(22.5) 7.5
7φ
9.5h
8 0 -0
.022
C0.3C0.5
M6×0.75
30°×0.5
8 0-0.2
R0.2max
3
4
C0.5
4
φ16
g6-0
.006
-0.0
17
C0.5
18
4-φ3.4
30° 30°
PCD 23
φ29
16
(12)
φ7.
5
L4
L3
L2
L1
Standard products in stock SG series標準在庫品 SGシリーズ
SG0802.5 Shaft dia.(軸径)φ8 Lead(リード)2.5mm C5
Support-unit Recommendation推奨サポートユニット
Supported-side 支持側 : MSU-6CS/6GSFixed-side 固定側 : MSU-6C/6G
L5:Thread length after end-journal machining. 追加工後のねじ部長さL6:Total length after end-journal machining. 追加工後全長
Supported-side end-journal profile 支持側端末加工形状
Unit(単位):mm
Ball Screw Modelボールねじ型番
Travelストローク
Grade精度
Shaft lengthねじ軸長さ
Lead accuracyリード精度 Total
Run-out全振れ
Axialplay
軸方向すきま
PreloadTorque予圧トルク
Nm
Basic Load Rating基本定格荷重 N
L1 L2 L3 L4
Travel deviation代表移動量誤差
ep
Variation変動Vu
Dynamic動定格荷重
Ca
Static静定格荷重
Coa
SG0802.5-129R170C5 110 C5 129 133 140 170 ±0.020 0.018 0.050~0.005 ― 1850 3000
SG0802.5-209R250C5 190 C5 209 213 220 250 ±0.023 0.018 0.065
Note)Please refer to page A206 for order code of end-journal machining. 注)追加工の呼び番号指定はぺージA206をご参照ください。
Unit(単位):mm
Ball Screw Specifications 諸元
Ball size ボール径 φ2.0
Number of thread 条数 1
Thread direction 巻方向 Right 右
Shaft root dia. ねじ軸谷径 φ6.2
Number of circuit 循環数 2.7×1
Shaft, Nut material軸、ナット材質 SCM415H
Surface hardnessねじ部表面硬度
HRC58~62(Thread area)
Anti-rust treatment防錆処理
Anti-rust oil防錆油
A04-AG0804
E
下表参照 G
E0.005
C5:0.010C3:0.008
C5:0.012C3:0.010
C5:0.010C3:0.008
C5:0.005C3:0.004
see table below
A
G
G
A
E
A
φ4.
5h6
0 -0.0
08
φ6
-0.0
01-0
.006
30
(7)
(22.5) 7.5
7
φ9.
5h8
0 -0.0
22
C0.3C0.5
M6×0.75
30°×0.5
φ8
8 0-0.2
R0.2max
3
C0.5
φ21
g6-0
.007
-0.0
20
PCD 31
2-φ4.5
23
φ39
28
(23)
C0.5
5
(5)
L4
L3
L2
L1
Standard products in stock SG series標準在庫品 SGシリーズ
SG0804 Shaft dia.(軸径)φ8 Lead(リード)4mm C3&C5
Support-unit Recommendation推奨サポートユニット
Supported-side 支持側 : MSU-6CS/6GSFixed-side 固定側 : MSU-6C/6G
L5:Thread length after end-journal machining. 追加工後のねじ部長さL6:Total length after end-journal machining. 追加工後全長
Supported-side end-journal profile 支持側端末加工形状
Unit(単位):mm
Ball Screw Modelボールねじ型番
Travelストローク
Grade精度
Shaft lengthねじ軸長さ
Lead accuracyリード精度 Total
Run-out全振れ
Axialplay
軸方向すきま
PreloadTorque予圧トルク
Nm
Basic Load Rating基本定格荷重 N
L1 L2 L3 L4
Travel deviation代表移動量誤差
ep
Variation変動Vu
Dynamic動定格荷重
Ca
Static静定格荷重
Coa
SG0804-098R140C3 70 C3 98 103 110 140 ±0.008 0.008 0.035 0Spacer Ballスペーサボール(1:1)
~0.015 1650 2100SG0804-208R250C3 180 C3 208 213 220 250 ±0.012 0.008 0.050
SG0804-098R140C5 70 C5 98 103 110 140 ±0.018 0.018 0.050~0.005 ― 2600 4200
SG0804-208R250C5 180 C5 208 213 220 250 ±0.023 0.018 0.065
Note)Please refer to page A206 for order code of end-journal machining. 注)追加工の呼び番号指定はぺージA206をご参照ください。
A04-φ08journal
A-type B-type C-type
6.8 +0.1 0
0.8 +0.1 0
φ5.
7 0 -0.
06
φ6-
0.00
2-
0.01
0
R0.2max
9
L6
L6
L5=L6-41
L5=L6-50
L5=L6-50
φ6-
0.00
2-
0.01
0
R0.2max 9
L6
A-type B-type C-type
A04-φ08journal
A-type B-type C-type
6.8 +0.1 0
0.8 +0.1 0
φ5.
7 0 -0.
06
φ6-
0.00
2-
0.01
0
R0.2max
9
L6
L6
L5=L6-42
L5=L6-51
L5=L6-51
φ6-
0.00
2-
0.01
0
R0.2max 9
L6
A-type B-type C-type
D-type : Other than the above. 上記以外の形状 D-type : Other than the above. 上記以外の形状
A221 A222
ボー
ルね
じBall Scresw
標準
在庫
品
SGシ
リー
ズStandard products in stock SG
series
ボー
ルね
じBall Scresw
標準
在庫
品
SGシ
リー
ズStandard products in stock SG
series
Unit(単位):mm
Ball Screw Specifications 諸元
Ball size ボール径 φ1.5875
Number of thread 条数 1
Thread direction 巻方向 Right 右
Shaft root dia. ねじ軸谷径 φ6.6
Number of circuit 循環数 2.7×1
Shaft, Nut material軸、ナット材質 SCM415H
Surface hardnessねじ部表面硬度
HRC58~62(Thread area)
Anti-rust treatment防錆処理
Anti-rust oil防錆油
A04-SG0805
E
下表参照 G
E0.005
C5:0.010C3:0.008
C5:0.012C3:0.009
C5:0.010C3:0.008
C5:0.005C3:0.004
see table below
A
G
G
A
E
A
φ4.
5h6
0 -0.0
08
φ6
-0.0
01-0
.006
30
(7)
(22.5) 7.5
7
φ9.
5h8
0 -0.0
22
C0.3C0.5
M6×0.75
30°×0.5
φ8
8 0-0.2
R0.2max
3
C0.5
PCD 25
20(4)
φ31
4 2-φ3.4
φ18
g6-0
.006
-0.0
17
28
(24)
C0.5
L4
L3
L2
L1
Standard products in stock SG series標準在庫品 SGシリーズ
SG0805 Shaft dia.(軸径)φ8 Lead(リード)5mm C3&C5
Support-unit Recommendation推奨サポートユニット
Supported-side 支持側 : MSU-6CS/6GSFixed-side 固定側 : MSU-6C/6G
L5:Thread length after end-journal machining. 追加工後のねじ部長さL6:Total length after end-journal machining. 追加工後全長
Supported-side end-journal profile 支持側端末加工形状
Unit(単位):mm
Ball Screw Modelボールねじ型番
Travelストローク
Grade精度
Shaft lengthねじ軸長さ
Lead accuracyリード精度 Total
Run-out全振れ
Axialplay
軸方向すきま
PreloadTorque予圧トルク
Nm
Basic Load Rating基本定格荷重 N
L1 L2 L3 L4
Travel deviation代表移動量誤差
ep
Variation変動Vu
Dynamic動定格荷重
Ca
Static静定格荷重
Coa
SG0805-099R140C3 70 C3 99 103 110 140 ±0.008 0.008 0.035 0Spacer Ballスペーサボール(1:1)
~0.015 1150 1500SG0805-209R250C3 180 C3 209 213 220 250 ±0.012 0.008 0.050
SG0805-099R140C5 70 C5 99 103 110 140 ±0.018 0.018 0.050~0.005 ― 1850 3000
SG0805-209R250C5 180 C5 209 213 220 250 ±0.023 0.018 0.065
Note)Please refer to page A206 for order code of end-journal machining. 注)追加工の呼び番号指定はぺージA206をご参照ください。
Unit(単位):mm
Ball Screw Modelボールねじ型番
Travelストローク
Grade精度
Shaft lengthねじ軸長さ
Lead accuracyリード精度 Total
Run-out全振れ
Axialplay
軸方向すきま
PreloadTorque予圧トルク
Nm
Basic Load Rating基本定格荷重 N
L1 L2 L3 L4
Travel deviation代表移動量誤差
ep
Variation変動Vu
Dynamic動定格荷重
Ca
Static静定格荷重
Coa
SG0808-099R140C5 75 C5 99 103 110 140 ±0.018 0.018 0.050~0.005 ― 2200 3800
SG0808-209R250C5 185 C5 209 213 220 250 ±0.023 0.018 0.065
Note)Please refer to page A206 for order code of end-journal machining. 注)追加工の呼び番号指定はぺージA206をご参照ください。
Unit(単位):mm
Ball Screw Specifications 諸元
Ball size ボール径 φ1.5875
Number of thread 条数 2
Thread direction 巻方向 Right 右
Shaft root dia. ねじ軸谷径 φ6.7
Number of circuit 循環数 1.6×2
Shaft, Nut material軸、ナット材質 SCM415H
Surface hardnessねじ部表面硬度
HRC58~62(Thread area)
Anti-rust treatment防錆処理
Anti-rust oil防錆油
A04-SG0808
E
下表参照 G
E0.005
see table below
A
G
G
A
E
A
0.005
0.012
0.010
0.010
φ4.
5h6
0 -0.0
08
φ6
-0.0
01-0
.006
30
(7)
(22.5) 7.5
7
φ9.
5h8
0 -0.0
22
C0.3C0.5
M6×0.75
30°×0.5
φ8
8 0-0.2
R0.2max
3
C0.5
(4)
PCD 25
φ31φ
18g6
-0.0
06-0
.017
20
4-φ3.4
30°
20
(10) 4
30°
L4
L3
L2
L1
Standard products in stock SG series標準在庫品 SGシリーズ
SG0808 Shaft dia.(軸径)φ8 Lead(リード)8mm C5
Support-unit Recommendation推奨サポートユニット
Supported-side 支持側 : MSU-6CS/6GSFixed-side 固定側 : MSU-6C/6G
L5:Thread length after end-journal machining. 追加工後のねじ部長さL6:Total length after end-journal machining. 追加工後全長
Supported-side end-journal profile 支持側端末加工形状
A04-φ08journal
A-type B-type C-type
6.8 +0.1 0
0.8 +0.1 0
φ5.
7 0 -0.
06
φ6-
0.00
2-
0.01
0
R0.2max
9
L6
L6
L5=L6-41
L5=L6-50
L5=L6-50
φ6-
0.00
2-
0.01
0
R0.2max 9
L6
A-type B-type C-type
A04-φ08journal
A-type B-type C-type
6.8 +0.1 0
0.8 +0.1 0
φ5.
7 0 -0.
06
φ6-
0.00
2-
0.01
0
R0.2max
9
L6
L6
L5=L6-41
L5=L6-50
L5=L6-50
φ6-
0.00
2-
0.01
0
R0.2max 9
L6
A-type B-type C-type
D-type : Other than the above. 上記以外の形状 D-type : Other than the above. 上記以外の形状
A223 A224
ボー
ルね
じBall Scresw
標準
在庫
品
SGシ
リー
ズStandard products in stock SG
series
ボー
ルね
じBall Scresw
標準
在庫
品
SGシ
リー
ズStandard products in stock SG
series
Unit(単位):mm
Ball Screw Modelボールねじ型番
Travelストローク
Grade精度
Shaft lengthねじ軸長さ
Lead accuracyリード精度 Total
Run-out全振れ
Axialplay
軸方向すきま
PreloadTorque予圧トルク
Nm
Basic Load Rating基本定格荷重 N
L1 L2 L3 L4
Travel deviation代表移動量誤差
ep
Variation変動Vu
Dynamic動定格荷重
Ca
Static静定格荷重
Coa
SG0812-097R140C5 70 C5 97 103 110 140 ±0.018 0.018 0.050~0.005 ― 2200 4000
SG0812-207R250C5 180 C5 207 213 220 250 ±0.023 0.018 0.065
Note)Please refer to page A206 for order code of end-journal machining. 注)追加工の呼び番号指定はぺージA206をご参照ください。
Unit(単位):mm
Ball Screw Specifications 諸元
Ball size ボール径 φ1.5875
Number of thread 条数 2
Thread direction 巻方向 Right 右
Shaft root dia. ねじ軸谷径 φ6.7
Number of circuit 循環数 1.6×2
Shaft, Nut material軸、ナット材質 SCM415H
Surface hardnessねじ部表面硬度
HRC58~62(Thread area)
Anti-rust treatment防錆処理
Anti-rust oil防錆油
A04-SG0812
E
下表参照 G
E0.005
see table below
A
G
G
A
E
A
0.005
0.012
0.010
0.010
φ4.
5h6
0 -0.0
08
φ6
-0.0
01-0
.006
30
(7)
(22.5) 7.5
7
φ9.
5h8
0 -0.0
22
C0.3C0.5
M6×0.75
30°×0.5
φ8
8 0-0.2
R0.2max
3
C0.5
(6)
PCD 25
φ31
φ18
g6-0
.006
-0.0
17
20
4
27
(17)4-φ3.4
30° 30°
L4
L3
L2
L1
Standard products in stock SG series標準在庫品 SGシリーズ
SG0812 Shaft dia.(軸径)φ8 Lead(リード)12mm C5
Support-unit Recommendation推奨サポートユニット
Supported-side 支持側 : MSU-6CS/6GSFixed-side 固定側 : MSU-6C/6G
L5:Thread length after end-journal machining. 追加工後のねじ部長さL6:Total length after end-journal machining. 追加工後全長
Supported-side end-journal profile 支持側端末加工形状
Unit(単位):mm
Ball Screw Specifications 諸元
Ball size ボール径 φ0.8
Number of thread 条数 1
Thread direction 巻方向 Right 右
Shaft root dia. ねじ軸谷径 φ9.3
Number of circuit 循環数 3.7×1
Shaft, Nut material軸、ナット材質 SCM415H
Surface hardnessねじ部表面硬度
HRC58~62(Thread area)
Anti-rust treatment防錆処理
Anti-rust oil防錆油
A04-SG1001
E
下表参照 G
C5:0.010C3:0.008
C5:0.012C3:0.009
C5:0.011C3:0.008
C5:0.005C3:0.004
see table below
A
G
G
0.005
E
A
E
A
R0.2max
4
C0.5
10 0-0.2
φ11
.5h8
0 -0.0
27
30°×0.5
M8×1.0
φ6h
6 0 -0
.008
9
37
C0.5
φ8
-0.0
02-0
.008
10
(8)
(27)
φ19
g6-0
.007
-0.0
20
PCD 29
18
21
2-φ4.55(13)
φ37
C0.5
(3)
φ10
C0.5
L4
L3
L2
L1
Standard products in stock SG series標準在庫品 SGシリーズ
SG1001 Shaft dia.(軸径)φ10 Lead(リード)1mm C3&C5
Support-unit Recommendation推奨サポートユニット
Supported-side 支持側 : MSU-8CS/8GSFixed-side 固定側 : MSU-8C/8G
L5:Thread length after end-journal machining. 追加工後のねじ部長さL6:Total length after end-journal machining. 追加工後全長
Supported-side end-journal profile 支持側端末加工形状
Unit(単位):mm
Ball Screw Modelボールねじ型番
Travelストローク
Grade精度
Shaft lengthねじ軸長さ
Lead accuracyリード精度 Total
Run-out全振れ
Axialplay
軸方向すきま
PreloadTorque予圧トルク
Nm
Basic Load Rating基本定格荷重 N
L1 L2 L3 L4
Travel deviation代表移動量誤差
ep
Variation変動Vu
Dynamic動定格荷重
Ca
Static静定格荷重
Coa
SG1001-112R160C3 90 C3 112 115 123 160 ±0.010 0.008 0.035
0Spacer Ballスペーサボール(1:1)
~0.020 530 1000SG1001-162R210C3 140 C3 162 165 173 210 ±0.010 0.008 0.040
SG1001-212R260C3 190 C3 212 215 223 260 ±0.012 0.008 0.040
SG1001-262R310C3 240 C3 262 265 273 310 ±0.012 0.008 0.040
SG1001-112R160C5 90 C5 112 115 123 160 ±0.020 0.018 0.040
~0.005 ー 840 2000SG1001-162R210C5 140 C5 162 165 173 210 ±0.020 0.018 0.055
SG1001-212R260C5 190 C5 212 215 223 260 ±0.023 0.018 0.055
SG1001-262R310C5 240 C5 262 265 273 310 ±0.023 0.018 0.055
Note)Please refer to page A206 for order code of end-journal machining. 注)追加工の呼び番号指定はぺージA206をご参照ください。
A04-φ08journal
A-type B-type C-type
6.8 +0.1 0
0.8 +0.1 0
φ5.
7 0 -0.
06
φ6-
0.00
2-
0.01
0
R0.2max
9
L6
L6
L5=L6-43
L5=L6-52
L5=L6-52
φ6-
0.00
2-
0.01
0
R0.2max 9
L6
A-type B-type C-type
A04-φ10journal
A-type B-type C-type
L5=L6-48
6.8
0.8+0.1 0
+0.1 0
φ5.
7 0 -0.
06
φ6-
0.00
2-
0.01
0
R0.2max
9
L6
L5=L6-57
φ6-
0.00
2-
0.01
0
R0.2max9
L6
L5=L6-57
L6
A-type B-type C-type
D-type : Other than the above. 上記以外の形状
D-type : Other than the above. 上記以外の形状
A225 A226
ボー
ルね
じBall Scresw
標準
在庫
品
SGシ
リー
ズStandard products in stock SG
series
ボー
ルね
じBall Scresw
標準
在庫
品
SGシ
リー
ズStandard products in stock SG
series
Unit(単位):mm
Ball Screw Specifications 諸元
Ball size ボール径 φ1.5875
Number of thread 条数 1
Thread direction 巻方向 Right 右
Shaft root dia. ねじ軸谷径 φ8.6
Number of circuit 循環数 3.7×1
Shaft, Nut material軸、ナット材質 SCM415H
Surface hardnessねじ部表面硬度
HRC58~62(Thread area)
Anti-rust treatment防錆処理
Anti-rust oil防錆油
A04-SG1002
E
下表参照 G
C5:0.010C3:0.008
C5:0.012C3:0.010
C5:0.011C3:0.008
C5:0.005C3:0.004
see table below
A
G
G
0.005
E
A
E
A
R0.2max
4
C0.5
10 0-0.2
φ11
.5h8
0 -0.0
27
30°×0.5
M8×1.0
φ6h
6 0 -0
.008
9
37
C0.5
φ8
-0.0
02-0
.008
10
(8)
(27)(4)
φ10
C0.5
φ23
g6-0
.007
-0.0
2024
(19) 5
25
PCD 33
2-φ4.5
C0.5
φ41
L4
L3
L2
L1
Standard products in stock SG series標準在庫品 SGシリーズ
SG1002 Shaft dia.(軸径)φ10 Lead(リード)2mm C3&C5
Support-unit Recommendation推奨サポートユニット
Supported-side 支持側 : MSU-8CS/8GSFixed-side 固定側 : MSU-8C/8G
L5:Thread length after end-journal machining. 追加工後のねじ部長さL6:Total length after end-journal machining. 追加工後全長
Supported-side end-journal profile 支持側端末加工形状
Unit(単位):mm
Ball Screw Modelボールねじ型番
Travelストローク
Grade精度
Shaft lengthねじ軸長さ
Lead accuracyリード精度 Total
Run-out全振れ
Axialplay
軸方向すきま
PreloadTorque予圧トルク
Nm
Basic Load Rating基本定格荷重 N
L1 L2 L3 L4
Travel deviation代表移動量誤差
ep
Variation変動Vu
Dynamic動定格荷重
Ca
Static静定格荷重
Coa
SG1002-111R160C3 85 C3 111 115 123 160 ±0.010 0.008 0.035
0Spacer Ballスペーサボール(1:1)
0.006~0.030 1750 2700
SG1002-161R210C3 135 C3 161 165 173 210 ±0.010 0.008 0.040
SG1002-211R260C3 185 C3 211 215 223 260 ±0.012 0.008 0.040
SG1002-261R310C3 235 C3 261 265 273 310 ±0.012 0.008 0.040
SG1002-111R160C5 85 C5 111 115 123 160 ±0.020 0.018 0.040
~0.005 ー 2700 5300SG1002-161R210C5 135 C5 161 165 173 210 ±0.020 0.018 0.055
SG1002-211R260C5 185 C5 211 215 223 260 ±0.023 0.018 0.055
SG1002-261R310C5 235 C5 261 265 273 310 ±0.023 0.018 0.055
Note)Please refer to page A206 for order code of end-journal machining. 注)追加工の呼び番号指定はぺージA206をご参照ください。
Unit(単位):mm
Ball Screw Specifications 諸元
Ball size ボール径 φ2.0
Number of thread 条数 1
Thread direction 巻方向 Right 右
Shaft root dia. ねじ軸谷径 φ8.2
Number of circuit 循環数 2.7×1
Shaft, Nut material軸、ナット材質 SCM415H
Surface hardnessねじ部表面硬度
HRC58~62(Thread area)
Anti-rust treatment防錆処理
Anti-rust oil防錆油
A04-SG1004
E
下表参照 G
C5:0.010C3:0.008
C5:0.012C3:0.010
C5:0.011C3:0.008
C5:0.005C3:0.004
see table below
A
G
G
0.005
E
A
E
A
R0.2max
4
C0.5
10 0-0.2
φ11
.5h8
0 -0.0
27
30°×0.5
M8×1.0
φ6h
6 0 -0
.008
9
37
C0.5
φ8
-0.0
02-0
.008
10
(8)
(27)(5)
φ10
C0.5
PCD 35
2-φ5.5
26
φ24
g6-0
.007
-0.0
20
φ44
6
29
(23)
C1
L4
L3
L2
L1
Standard products in stock SG series標準在庫品 SGシリーズ
SG1004 Shaft dia.(軸径)φ10 Lead(リード)4mm C3&C5
Support-unit Recommendation推奨サポートユニット
Supported-side 支持側 : MSU-8CS/8GSFixed-side 固定側 : MSU-8C/8G
L5:Thread length after end-journal machining. 追加工後のねじ部長さL6:Total length after end-journal machining. 追加工後全長
Supported-side end-journal profile 支持側端末加工形状
Unit(単位):mm
Ball Screw Modelボールねじ型番
Travelストローク
Grade精度
Shaft lengthねじ軸長さ
Lead accuracyリード精度 Total
Run-out全振れ
Axialplay
軸方向すきま
PreloadTorque予圧トルク
Nm
Basic Load Rating基本定格荷重 N
L1 L2 L3 L4
Travel deviation代表移動量誤差
ep
Variation変動Vu
Dynamic動定格荷重
Ca
Static静定格荷重
Coa
SG1004-110R160C3 80 C3 110 115 123 160 ±0.010 0.008 0.035 0Spacer Ballスペーサボール(1:1)
0.005~0.040 1800 2600
SG1004-260R310C3 230 C3 260 265 273 310 ±0.012 0.008 0.040
SG1004-110R160C5 80 C5 110 115 123 160 ±0.020 0.018 0.040~0.005 ― 3000 5200
SG1004-260R310C5 230 C5 260 265 273 310 ±0.023 0.018 0.055
Note)Please refer to page A206 for order code of end-journal machining. 注)追加工の呼び番号指定はぺージA206をご参照ください。
A04-φ10journal
A-type B-type C-type
L5=L6-49
6.8
0.8+0.1 0
+0.1 0
φ5.
7 0 -0.
06
φ6-
0.00
2-
0.01
0
R0.2max
9
L6
L5=L6-58
φ6-
0.00
2-
0.01
0
R0.2max9
L6
L5=L6-58
L6
A-type B-type C-type
A04-φ10journal
A-type B-type C-type
L5=L6-50
6.8
0.8+0.1 0
+0.1 0
φ5.
7 0 -0.
06
φ6-
0.00
2-
0.01
0
R0.2max
9
L6
L5=L6-59
φ6-
0.00
2-
0.01
0
R0.2max9
L6
L5=L6-59
L6
A-type B-type C-type
D-type : Other than the above. 上記以外の形状
D-type : Other than the above. 上記以外の形状
A227 A228
ボー
ルね
じBall Scresw
標準
在庫
品
SGシ
リー
ズStandard products in stock SG
series
ボー
ルね
じBall Scresw
標準
在庫
品
SGシ
リー
ズStandard products in stock SG
series
Unit(単位):mm
Ball Screw Specifications 諸元
Ball size ボール径 φ2.0
Number of thread 条数 1
Thread direction 巻方向 Right 右
Shaft root dia. ねじ軸谷径 φ8.2
Number of circuit 循環数 2.7×1
Shaft, Nut material軸、ナット材質 SCM415H
Surface hardnessねじ部表面硬度
HRC58~62(Thread area)
Anti-rust treatment防錆処理
Anti-rust oil防錆油
A04-SG1005
E
下表参照 G
C5:0.010C3:0.008
C5:0.012C3:0.010
C5:0.011C3:0.008
C5:0.005C3:0.004
see table below
A
G
G
0.005
E
A
E
A
R0.2max
4
C0.5
10 0-0.2
φ11
.5h8
0 -0.0
27
30°×0.5
M8×1.0
φ6h
6 0 -0
.008
9
37
C0.5
φ8
-0.0
02-0
.008
10
(8)
(27)(5)
φ10
C0.5
PCD 35
2-φ5.5
26
φ24
g6-0
.007
-0.0
20
φ44
6
34
(28)
C1
L4
L3
L2
L1
Standard products in stock SG series標準在庫品 SGシリーズ
SG1005 Shaft dia.(軸径)φ10 Lead(リード)5mm C3&C5
Support-unit Recommendation推奨サポートユニット
Supported-side 支持側 : MSU-8CS/8GSFixed-side 固定側 : MSU-8C/8G
L5:Thread length after end-journal machining. 追加工後のねじ部長さL6:Total length after end-journal machining. 追加工後全長
Supported-side end-journal profile 支持側端末加工形状
Unit(単位):mm
Ball Screw Modelボールねじ型番
Travelストローク
Grade精度
Shaft lengthねじ軸長さ
Lead accuracyリード精度 Total
Run-out全振れ
Axialplay
軸方向すきま
PreloadTorque予圧トルク
Nm
Basic Load Rating基本定格荷重 N
L1 L2 L3 L4
Travel deviation代表移動量誤差
ep
Variation変動Vu
Dynamic動定格荷重
Ca
Static静定格荷重
Coa
SG1005-110R160C3 75 C3 110 115 123 160 ±0.010 0.008 0.035 0Spacer Ballスペーサボール(1:1)
0.005~0.040 1800 2600
SG1005-260R310C3 225 C3 260 265 273 310 ±0.012 0.008 0.040
SG1005-110R160C5 75 C5 110 115 123 160 ±0.020 0.018 0.040~0.005 ― 3000 5200
SG1005-260R310C5 225 C5 260 265 273 310 ±0.023 0.018 0.055
Note)Please refer to page A206 for order code of end-journal machining. 注)追加工の呼び番号指定はぺージA206をご参照ください。
Unit(単位):mm
Ball Screw Modelボールねじ型番
Travelストローク
Grade精度
Shaft lengthねじ軸長さ
Lead accuracyリード精度 Total
Run-out全振れ
Axialplay
軸方向すきま
PreloadTorque予圧トルク
Nm
Basic Load Rating基本定格荷重 N
L1 L2 L3 L4
Travel deviation代表移動量誤差
ep
Variation変動Vu
Dynamic動定格荷重
Ca
Static静定格荷重
Coa
SG1010-110R160C5 85 C5 110 115 123 160 ±0.020 0.018 0.040~0.005 ― 3300 5900
SG1010-260R310C5 235 C5 260 265 273 310 ±0.023 0.018 0.055
Note)Please refer to page A206 for order code of end-journal machining. 注)追加工の呼び番号指定はぺージA206をご参照ください。
Unit(単位):mm
Ball Screw Specifications 諸元
Ball size ボール径 φ2.0
Number of thread 条数 2
Thread direction 巻方向 Right 右
Shaft root dia. ねじ軸谷径 φ8.4
Number of circuit 循環数 1.6×2
Shaft, Nut material軸、ナット材質 SCM415H
Surface hardnessねじ部表面硬度
HRC58~62(Thread area)
Anti-rust treatment防錆処理
Anti-rust oil防錆油
A04-SG1010
下表参照 G
see table below
A
G
G
A
0.012
0.010
φ10
C0.5
φ23
g6-0
.007
-0.0
20
24
(13) 5
E0.005
φ11
.5h8
0 -0.0
27
37
(8)
φ40
E
A0.011
R0.2max
4
10 0-0.2
30°×0.5
9
φ8
-0.0
02-0
.008
10(27)(5)
0.005 E
C0.5
M8×1.0
φ6h
6 0 -0
.008
C0.5
30°
PCD 32
25
4-φ4.5
30°
L4
L3
L2
L1
Standard products in stock SG series標準在庫品 SGシリーズ
SG1010 Shaft dia.(軸径)φ10 Lead(リード)10mm C5
Support-unit Recommendation推奨サポートユニット
Supported-side 支持側 : MSU-8CS/8GSFixed-side 固定側 : MSU-8C/8G
L5:Thread length after end-journal machining. 追加工後のねじ部長さL6:Total length after end-journal machining. 追加工後全長
Supported-side end-journal profile 支持側端末加工形状
A04-φ10journal
A-type B-type C-type
L5=L6-50
6.8
0.8+0.1 0
+0.1 0
φ5.
7 0 -0.
06
φ6-
0.00
2-
0.01
0
R0.2max
9
L6
L5=L6-59
φ6-
0.00
2-
0.01
0
R0.2max9
L6
L5=L6-59
L6
A-type B-type C-type
A04-φ10journal
A-type B-type C-type
L5=L6-50
6.8
0.8+0.1 0
+0.1 0
φ5.
7 0 -0.
06
φ6-
0.00
2-
0.01
0
R0.2max
9
L6
L5=L6-59
φ6-
0.00
2-
0.01
0
R0.2max9
L6
L5=L6-59
L6
A-type B-type C-type
D-type : Other than the above. 上記以外の形状 D-type : Other than the above. 上記以外の形状
A229 A230
ボー
ルね
じBall Scresw
標準
在庫
品
SGシ
リー
ズStandard products in stock SG
series
ボー
ルね
じBall Scresw
標準
在庫
品
SGシ
リー
ズStandard products in stock SG
series
Unit(単位):mm
Ball Screw Modelボールねじ型番
Travelストローク
Grade精度
Shaft lengthねじ軸長さ
Lead accuracyリード精度 Total
Run-out全振れ
Axialplay
軸方向すきま
PreloadTorque予圧トルク
Nm
Basic Load Rating基本定格荷重 N
L1 L2 L3 L4
Travel deviation代表移動量誤差
ep
Variation変動Vu
Dynamic動定格荷重
Ca
Static静定格荷重
Coa
SG1015-107R160C5 70 C5 107 115 123 160 ±0.020 0.018 0.040~0.005 ― 3300 6400
SG1015-257R310C5 220 C5 257 265 273 310 ±0.023 0.018 0.055
Note)Please refer to page A206 for order code of end-journal machining. 注)追加工の呼び番号指定はぺージA206をご参照ください。
Unit(単位):mm
Ball Screw Specifications 諸元
Ball size ボール径 φ2.0
Number of thread 条数 2
Thread direction 巻方向 Right 右
Shaft root dia. ねじ軸谷径 φ8.4
Number of circuit 循環数 1.6×2
Shaft, Nut material軸、ナット材質 SCM415H
Surface hardnessねじ部表面硬度
HRC58~62(Thread area)
Anti-rust treatment防錆処理
Anti-rust oil防錆油
A04-SG1015
E
下表参照 G
see table below
A
G
G
0.005
E
A
E
A
0.005
0.011
0.012
0.010
R0.2max
4
C0.5
10 0-0.2
φ11
.5h8
0 -0.0
27
30°×0.5
M8×1.0
φ6h
6 0 -0
.008
9
37
C0.5φ8
-0.0
02-0
.008
10
(8)
(27)
(8)
φ10
C0.5
33
(22) 5
30°
PCD 32
25
4-φ4.5
30°
φ40φ
23g6
-0.0
07-0
.020
L4
L3
L2
L1
Standard products in stock SG series標準在庫品 SGシリーズ
SG1015 Shaft dia.(軸径)φ10 Lead(リード)15mm C5
Support-unit Recommendation推奨サポートユニット
Supported-side 支持側 : MSU-8CS/8GSFixed-side 固定側 : MSU-8C/8G
L5:Thread length after end-journal machining. 追加工後のねじ部長さL6:Total length after end-journal machining. 追加工後全長
Supported-side end-journal profile 支持側端末加工形状
Unit(単位):mm
Ball Screw Specifications 諸元
Ball size ボール径 φ1.5875
Number of thread 条数 1
Thread direction 巻方向 Right 右
Shaft root dia. ねじ軸谷径 φ10.6
Number of circuit 循環数 3.7×1
Shaft, Nut material軸、ナット材質 SCM415H
Surface hardnessねじ部表面硬度
HRC58~62(Thread area)
Anti-rust treatment防錆処理
Anti-rust oil防錆油
A04-SG1202
E
下表参照 G
C5:0.010C3:0.008
C5:0.012C3:0.010
C5:0.011C3:0.008
C5:0.005C3:0.004
see table below
A
G
G
0.005
E
A
E
A
30°×0.5
φ8h
6 0 -0
.009
φ10
-0.0
02-0
.008
φ25
g6-0
.007
-0.0
20
27
PCD 36
45
(10)
(4)(30) 15
C0.5C0.5
M10×1.0
10R0.2max
25
(19) 6
φ12
12 0-0.25
2-φ5.5
5
C0.5
φ14
h8 0 -0
.027
C0.5
φ45
L4
L3
L2
L1
Standard products in stock SG series標準在庫品 SGシリーズ
SG1202 Shaft dia.(軸径)φ12 Lead(リード)2mm C3&C5
Support-unit Recommendation推奨サポートユニット
Supported-side 支持側 : ─Fixed-side 固定側 : ─
L5:Thread length after end-journal machining. 追加工後のねじ部長さL6:Total length after end-journal machining. 追加工後全長
Supported-side end-journal profile 支持側端末加工形状
Unit(単位):mm
Ball Screw Modelボールねじ型番
Travelストローク
Grade精度
Shaft lengthねじ軸長さ
Lead accuracyリード精度 Total
Run-out全振れ
Axialplay
軸方向すきま
PreloadTorque予圧トルク
Nm
Basic Load Rating基本定格荷重 N
L1 L2 L3 L4
Travel deviation代表移動量誤差
ep
Variation変動Vu
Dynamic動定格荷重
Ca
Static静定格荷重
Coa
SG1202-141R200C3 115 C3 141 145 155 200 ±0.010 0.008 0.035
0Spacer Ballスペーサボール(1:1)
0.008~0.040 1900 3200
SG1202-191R250C3 165 C3 191 195 205 250 ±0.010 0.008 0.040
SG1202-241R300C3 215 C3 241 245 255 300 ±0.012 0.008 0.040
SG1202-291R350C3 265 C3 291 295 305 350 ±0.012 0.008 0.050
SG1202-341R400C3 315 C3 341 345 355 400 ±0.013 0.010 0.050
SG1202-141R200C5 115 C5 141 145 155 200 ±0.020 0.018 0.040
~0.005 ー 3000 6400
SG1202-191R250C5 165 C5 191 195 205 250 ±0.020 0.018 0.055
SG1202-241R300C5 215 C5 241 245 255 300 ±0.023 0.018 0.055
SG1202-291R350C5 265 C5 291 295 305 350 ±0.023 0.018 0.065
SG1202-341R400C5 315 C5 341 345 355 400 ±0.025 0.020 0.065
Note)Please refer to page A206 for order code of end-journal machining. 注)追加工の呼び番号指定はぺージA206をご参照ください。
A04-φ10journal
A-type B-type C-type
L5=L6-53
6.8
0.8+0.1 0
+0.1 0
φ5.
7 0 -0.
06
φ6-
0.00
2-
0.01
0
R0.2max
9
L6
L5=L6-62
φ6-
0.00
2-
0.01
0
R0.2max9
L6
L5=L6-62
L6
A-type B-type C-type
A04-φ12journal
A-type B-type C-type
10
7.9
R0.2max
L6
L5=L6-69
L6
L5=L6-6910
L6
L5=L6-59R0.2max
0.9+0.1 0
+0.1 0
φ8-
0.00
4-
0.01
2
φ7.
6 0 -0.
08
φ8
-0.
004
-0.
012
A-type B-type C-type
D-type : Other than the above. 上記以外の形状
D-type : Other than the above. 上記以外の形状
A231 A232
ボー
ルね
じBall Scresw
標準
在庫
品
SGシ
リー
ズStandard products in stock SG
series
ボー
ルね
じBall Scresw
標準
在庫
品
SGシ
リー
ズStandard products in stock SG
series
Unit(単位):mm
Ball Screw Modelボールねじ型番
Travelストローク
Grade精度
Shaft lengthねじ軸長さ
Lead accuracyリード精度 Total
Run-out全振れ
Axialplay
軸方向すきま
PreloadTorque予圧トルク
Nm
Basic Load Rating基本定格荷重 N
L1 L2 L3 L4
Travel deviation代表移動量誤差
ep
Variation変動Vu
Dynamic動定格荷重
Ca
Static静定格荷重
Coa
SG1210-240R300C5 210 C5 240 245 255 300 ±0.023 0.018 0.055~0.005 ― 5100 9800
SG1210-340R400C5 310 C5 340 345 355 400 ±0.025 0.020 0.065
Note)Please refer to page A206 for order code of end-journal machining. 注)追加工の呼び番号指定はぺージA206をご参照ください。
Unit(単位):mm
Ball Screw Specifications 諸元
Ball size ボール径 φ2.381
Number of thread 条数 2
Thread direction 巻方向 Right 右
Shaft root dia. ねじ軸谷径 φ10.2
Number of circuit 循環数 1.7×2
Shaft, Nut material軸、ナット材質 SCM415H
Surface hardnessねじ部表面硬度
HRC58~62(Thread area)
Anti-rust treatment防錆処理
Anti-rust oil防錆油
A04-SG1210
E
下表参照 G
see table below
A
G
G
0.005
E
A
E
A
0.005
0.011
0.010
0.012
30°×0.5
φ8h
6 0 -0
.009
φ10
-0.0
02-0
.008
45
(10)
(30) 15
C0.5C0.5
M10×1.0
10
R0.2max
φ12
12 0-0.25
5
φ14
h8 0 -0
.027
C0.5
30°
4-φ4.5
30°
30
6(14.5)
φ24
g6-0
.007
-0.0
20
φ41
26
PCD 33
5
L4
L3
L2
L1
Standard products in stock SG series標準在庫品 SGシリーズ
SG1210 Shaft dia.(軸径)φ12 Lead(リード)10mm C5
Supported-side end-journal profile 支持側端末加工形状
L5:Thread length after end-journal machining. 追加工後のねじ部長さL6:Total length after end-journal machining. 追加工後全長
Support-unit Recommendation推奨サポートユニット
Supported-side 支持側 : ─Fixed-side 固定側 : ─
Unit(単位):mm
Ball Screw Specifications 諸元
Ball size ボール径 φ1.5875
Number of thread 条数 1
Thread direction 巻方向 Right 右
Shaft root dia. ねじ軸谷径 φ12.6
Number of circuit 循環数 3.7×1
Shaft, Nut material軸、ナット材質 SCM415H
Surface hardnessねじ部表面硬度
HRC58~62(Thread area)
Anti-rust treatment防錆処理
Anti-rust oil防錆油
A04-SG1402
E
下表参照 G
C5:0.010C3:0.008
C5:0.012C3:0.010
C5:0.012C3:0.009
C5:0.005C3:0.004
see table below
A
G
G
0.005
E
A
E
A
φ12
-0.0
03-0
.011
φ15
h8 0 -0
.027
φ10
h6 0 -0
.009
45
(10)
(30) 15
C0.5C0.5
30°×0.5M12×1.0
10
φ14
R0.2max
12 0-0.25
5
25
(19) 6
φ26
g6-0
.007
-0.0
20
PCD 37
C0.5
4-φ5.5
φ46
30°
284
C0.5
30°
L4
L3
L2
L1
Standard products in stock SG series標準在庫品 SGシリーズ
SG1402 Shaft dia.(軸径)φ14 Lead(リード)2mm C3&C5
Support-unit Recommendation推奨サポートユニット
Supported-side 支持側 : ─Fixed-side 固定側 : ─
L5:Thread length after end-journal machining. 追加工後のねじ部長さL6:Total length after end-journal machining. 追加工後全長
Supported-side end-journal profile 支持側端末加工形状
Unit(単位):mm
Ball Screw Modelボールねじ型番
Travelストローク
Grade精度
Shaft lengthねじ軸長さ
Lead accuracyリード精度 Total
Run-out全振れ
Axialplay
軸方向すきま
PreloadTorque予圧トルク
Nm
Basic Load Rating基本定格荷重 N
L1 L2 L3 L4
Travel deviation代表移動量誤差
ep
Variation変動Vu
Dynamic動定格荷重
Ca
Static静定格荷重
Coa
SG1402-141R200C3 115 C3 141 145 155 200 ±0.010 0.008 0.025
0Spacer Ballスペーサボール(1:1)
0.010~0.050 2000 3800
SG1402-191R250C3 165 C3 191 195 205 250 ±0.010 0.008 0.030
SG1402-241R300C3 215 C3 241 245 255 300 ±0.012 0.008 0.030
SG1402-291R350C3 265 C3 291 295 305 350 ±0.012 0.008 0.040
SG1402-391R450C3 365 C3 391 395 405 450 ±0.013 0.010 0.050
SG1402-141R200C5 115 C5 141 145 155 200 ±0.020 0.018 0.040
~0.005 ー 3200 7500
SG1402-191R250C5 165 C5 191 195 205 250 ±0.020 0.018 0.045
SG1402-241R300C5 215 C5 241 245 255 300 ±0.023 0.018 0.045
SG1402-291R350C5 265 C5 291 295 305 350 ±0.023 0.018 0.055
SG1402-391R450C5 365 C5 391 395 405 450 ±0.025 0.020 0.060
Note)Please refer to page A206 for order code of end-journal machining. 注)追加工の呼び番号指定はぺージA206をご参照ください。
A04-φ12journal
A-type B-type C-type
10
7.9
R0.2max
L6
L5=L6-70
L6
L5=L6-7010
L6
L5=L6-60R0.2max
0.9+0.1 0
+0.1 0
φ8-
0.00
4-
0.01
2
φ7.
6 0 -0.
08
φ8
-0.
004
-0.
012
A-type B-type C-type
A04-φ14journal
A-type B-type C-type
12
9.15 +0.1 0
R0.2max
L6
L5=L6-71
L6
L5=L6-7112
L6
L5=L6-59R0.2max
φ10-
0.00
4-
0.01
2
φ10-
0.00
4-
0.01
2
φ9.
6 0 -0.
09
1.15+0.14 0
A-type B-type C-type
D-type : Other than the above. 上記以外の形状
D-type : Other than the above. 上記以外の形状
A233 A234
ボー
ルね
じBall Scresw
標準
在庫
品
SGシ
リー
ズStandard products in stock SG
series
ボー
ルね
じBall Scresw
標準
在庫
品
SGシ
リー
ズStandard products in stock SG
series
Unit(単位):mm
Ball Screw Specifications 諸元
Ball size ボール径 φ2.381
Number of thread 条数 1
Thread direction 巻方向 Right 右
Shaft root dia. ねじ軸谷径 φ11.8
Number of circuit 循環数 3.7×1
Shaft, Nut material軸、ナット材質 SCM415H
Surface hardnessねじ部表面硬度
HRC58~62(Thread area)
Anti-rust treatment防錆処理
Anti-rust oil防錆油
A04-SG1404
E
下表参照 G
C5:0.010C3:0.008
C5:0.012C3:0.010
C5:0.012C3:0.009
C5:0.005C3:0.004
see table below
A
G
G
0.005
E
A
E
A
φ12
-0.0
03-0
.011
φ15
h8 0 -0
.027
φ10
h6 0 -0
.009
45
(10)
(30) 15
C0.5C0.5
30°×0.5
M12×1.0
10
φ14
R0.2max
12 0-0.25
5
φ30
g6-0
.007
-0.0
20
PCD 42
30°
5
C1
33
(27) 630°
4-φ5.5
φ51
C1
32
L4
L3
L2
L1
Standard products in stock SG series標準在庫品 SGシリーズ
SG1404 Shaft dia.(軸径)φ14 Lead(リード)4mm C3&C5
Support-unit Recommendation推奨サポートユニット
Supported-side 支持側 : ─Fixed-side 固定側 : ─
L5:Thread length after end-journal machining. 追加工後のねじ部長さL6:Total length after end-journal machining. 追加工後全長
Supported-side end-journal profile 支持側端末加工形状
Unit(単位):mm
Ball Screw Modelボールねじ型番
Travelストローク
Grade精度
Shaft lengthねじ軸長さ
Lead accuracyリード精度 Total
Run-out全振れ
Axialplay
軸方向すきま
PreloadTorque予圧トルク
Nm
Basic Load Rating基本定格荷重 N
L1 L2 L3 L4
Travel deviation代表移動量誤差
ep
Variation変動Vu
Dynamic動定格荷重
Ca
Static静定格荷重
Coa
SG1404-190R250C3 155 C3 190 195 205 250 ±0.010 0.008 0.030
0Spacer Ballスペーサボール(1:1)
0.020~0.070 3600 5800
SG1404-240R300C3 205 C3 240 245 255 300 ±0.012 0.008 0.030
SG1404-290R350C3 255 C3 290 295 305 350 ±0.012 0.008 0.040
SG1404-390R450C3 355 C3 390 395 405 450 ±0.013 0.010 0.050
SG1404-490R550C3 455 C3 490 495 505 550 ±0.015 0.010 0.055
SG1404-190R250C5 155 C5 190 195 205 250 ±0.020 0.018 0.045
~0.005 ー 5700 11600
SG1404-240R300C5 205 C5 240 245 255 300 ±0.023 0.018 0.045
SG1404-290R350C5 255 C5 290 295 305 350 ±0.023 0.018 0.055
SG1404-390R450C5 355 C5 390 395 405 450 ±0.025 0.020 0.060
SG1404-490R550C5 455 C5 490 495 505 550 ±0.027 0.020 0.075
Note)Please refer to page A206 for order code of end-journal machining. 注)追加工の呼び番号指定はぺージA206をご参照ください。
Unit(単位):mm
Ball Screw Modelボールねじ型番
Travelストローク
Grade精度
Shaft lengthねじ軸長さ
Lead accuracyリード精度 Total
Run-out全振れ
Axialplay
軸方向すきま
PreloadTorque予圧トルク
Nm
Basic Load Rating基本定格荷重 N
L1 L2 L3 L4
Travel deviation代表移動量誤差
ep
Variation変動Vu
Dynamic動定格荷重
Ca
Static静定格荷重
Coa
SG1505-340R400C5 305 C5 340 345 355 400 ±0.025 0.020 0.055~0.005 ― 8900 17000
SG1505-540R600C5 505 C5 540 545 555 600 ±0.030 0.023 0.075
Note)Please refer to page A206 for order code of end-journal machining. 注)追加工の呼び番号指定はぺージA206をご参照ください。
Unit(単位):mm
Ball Screw Specifications 諸元
Ball size ボール径 φ3.175
Number of thread 条数 1
Thread direction 巻方向 Right 右
Shaft root dia. ねじ軸谷径 φ12.2
Number of circuit 循環数 3.7×1
Shaft, Nut material軸、ナット材質 SCM415H
Surface hardnessねじ部表面硬度
HRC58~62(Thread area)
Anti-rust treatment防錆処理
Anti-rust oil防錆油
A04-SG1505
E
下表参照 G
see table below
A
G
G
0.005
E
A
E
A
M6(Oil hole/給油穴)
0.005
0.012
0.011
0.015
Depth/ 深 Facing/ざぐり
φ12
-0.0
03-0
.011
φ15
h8 0 -0
.027
φ10
h6 0 -0
.009
45
(10)
(30) 15
C0.5C0.5
30°×0.5
M12×1.0
10
R0.2max
12 0-0.25
5
5
PCD 45
φ34
g6-0
.009
-0.0
25
φ15 50
34
30°
4-φ5.5 φ9.5 5.5
30°
φ57
33
(16) 11
5.5
C1
L4
L3
L2
L1
Standard products in stock SG series標準在庫品 SGシリーズ
SG1505 Shaft dia.(軸径)φ15 Lead(リード)5mm C5
Supported-side end-journal profile 支持側端末加工形状
L5:Thread length after end-journal machining. 追加工後のねじ部長さL6:Total length after end-journal machining. 追加工後全長
Support-unit Recommendation推奨サポートユニット
Supported-side 支持側 : ─Fixed-side 固定側 : ─
A04-φ14journal
A-type B-type C-type
12
9.15 +0.1 0
R0.2max
L6
L5=L6-72
L6
L5=L6-7212
L6
L5=L6-60R0.2max
φ10-
0.00
4-
0.01
2
φ10-
0.00
4-
0.01
2
φ9.
6 0 -0.
09
1.15+0.14 0
A-type B-type C-type
A04-φ14journal
A-type B-type C-type
12
9.15 +0.1 0
R0.2max
L6
L5=L6-72
L6
L5=L6-7212
L6
L5=L6-60R0.2max
φ10-
0.00
4-
0.01
2
φ10-
0.00
4-
0.01
2
φ9.
6 0 -0.
09
1.15+0.14 0
A-type B-type C-type
D-type : Other than the above. 上記以外の形状
D-type : Other than the above. 上記以外の形状
A235 A236
ボー
ルね
じBall Scresw
標準
在庫
品
SGシ
リー
ズStandard products in stock SG
series
ボー
ルね
じBall Scresw
標準
在庫
品
SGシ
リー
ズStandard products in stock SG
series
Unit(単位):mm
Ball Screw Modelボールねじ型番
Travelストローク
Grade精度
Shaft lengthねじ軸長さ
Lead accuracyリード精度 Total
Run-out全振れ
Axialplay
軸方向すきま
PreloadTorque予圧トルク
Nm
Basic Load Rating基本定格荷重 N
L1 L2 L3 L4
Travel deviation代表移動量誤差
ep
Variation変動Vu
Dynamic動定格荷重
Ca
Static静定格荷重
Coa
SG1510-340R400C5 295 C5 340 345 355 400 ±0.025 0.020 0.055~0.005 ― 12000 25000
SG1510-540R600C5 495 C5 540 545 555 600 ±0.030 0.023 0.075
Note)Please refer to page A206 for order code of end-journal machining. 注)追加工の呼び番号指定はぺージA206をご参照ください。
Unit(単位):mm
Ball Screw Specifications 諸元
Ball size ボール径 φ3.175
Number of thread 条数 2
Thread direction 巻方向 Right 右
Shaft root dia. ねじ軸谷径 φ12.2
Number of circuit 循環数 2.7×2
Shaft, Nut material軸、ナット材質 SCM415H
Surface hardnessねじ部表面硬度
HRC58~62(Thread area)
Anti-rust treatment防錆処理
Anti-rust oil防錆油
A04-SG1510
E
下表参照 G
see table below
A
G
G
0.005
E
A
E
A
M6(Oil hole/給油穴)
0.005
0.012
0.011
0.015
φ12
-0.0
03-0
.011
φ15
h8 0 -0
.027
φ10
h6 0 -0
.009
45
(10)
(30) 15
C0.5C0.5
30°×0.5
M12×1.0
10
R0.2max
12 0-0.25
5
5
PCD 45
φ34
g6-0
.009
-0.0
25
φ15 50
34
30°
4-φ5.5φ9.5
30°
φ57
11
5.5
C1
43
(21)
Depth/ 深5.5 Facingざぐり
L4
L3
L2
L1
Standard products in stock SG series標準在庫品 SGシリーズ
SG1510 Shaft dia.(軸径)φ15 Lead(リード)10mm C5
L5:Thread length after end-journal machining. 追加工後のねじ部長さL6:Total length after end-journal machining. 追加工後全長
Supported-side end-journal profile 支持側端末加工形状
Support-unit Recommendation 推奨サポートユニット
Supported-side 支持側 : ─Fixed-side 固定側 : ─
Unit(単位):mm
Ball Screw Modelボールねじ型番
Travelストローク
Grade精度
Shaft lengthねじ軸長さ
Lead accuracyリード精度 Total
Run-out全振れ
Axialplay
軸方向すきま
PreloadTorque予圧トルク
Nm
Basic Load Rating基本定格荷重 N
L1 L2 L3 L4
Travel deviation代表移動量誤差
ep
Variation変動Vu
Dynamic動定格荷重
Ca
Static静定格荷重
Coa
SG1520-337R400C5 285 C5 337 345 355 400 ±0.025 0.020 0.055~0.005 ― 8000 16000
SG1520-537R600C5 485 C5 537 545 555 600 ±0.030 0.023 0.075
Note)Please refer to page A206 for order code of end-journal machining. 注)追加工の呼び番号指定はぺージA206をご参照ください。
Unit(単位):mm
Ball Screw Specifications 諸元
Ball size ボール径 φ3.175
Number of thread 条数 2
Thread direction 巻方向 Right 右
Shaft root dia. ねじ軸谷径 φ12.4
Number of circuit 循環数 1.7×2
Shaft, Nut material軸、ナット材質 SCM415H
Surface hardnessねじ部表面硬度
HRC58~62(Thread area)
Anti-rust treatment防錆処理
Anti-rust oil防錆油
A04-SG1520
E
下表参照 G
see table below
A
G
G
0.005
E
A
E
A
M6(Oil hole/給油穴)
0.005
0.012
0.011
0.015
φ12
-0.0
03-0
.011
φ15
h8 0 -0
.027
φ10
h6 0 -0
.009
45
(10)
(30) 15
C0.5C0.5
30°×0.5
M12×1.0
10
R0.2max
12 0-0.25
5
PCD 45
φ34
g6-0
.009
-0.0
25
φ15 50
34
30°
4-φ5.5 φ9.5 5.5
30°
φ57
11
5.5
C1
52
(28.5)
8
Depth/ 深 Facing/ざぐり
L4
L3
L2
L1
Standard products in stock SG series標準在庫品 SGシリーズ
SG1520 Shaft dia.(軸径)φ15 Lead(リード)20mm C5
L5:Thread length after end-journal machining. 追加工後のねじ部長さL6:Total length after end-journal machining. 追加工後全長
Supported-side end-journal profile 支持側端末加工形状
Support-unit Recommendation推奨サポートユニット
Supported-side 支持側 : ─Fixed-side 固定側 : ─
A04-φ14journal
A-type B-type C-type
12
9.15 +0.1 0
R0.2max
L6
L5=L6-72
L6
L5=L6-7212
L6
L5=L6-60R0.2max
φ10-
0.00
4-
0.01
2
φ10-
0.00
4-
0.01
2
φ9.
6 0 -0.
09
1.15+0.14 0
A-type B-type C-type
A04-φ14journal
A-type B-type C-type
12
9.15 +0.1 0
R0.2max
L6
L5=L6-75
L6
L5=L6-7512
L6
L5=L6-63R0.2max
φ10-
0.00
4-
0.01
2
φ10-
0.00
4-
0.01
2
φ9.
6 0 -0.
09
1.15+0.14 0
A-type B-type C-type
D-type : Other than the above. 上記以外の形状 D-type : Other than the above. 上記以外の形状
A237 A238
ボー
ルね
じBall Scresw
標準
在庫
品
SDシ
リー
ズStandard products in stock SD
series
ボー
ルね
じBall Scresw
標準
在庫
品
SDシ
リー
ズStandard products in stock SD
series
120 R 300 C5SD 08 01 120 Lー
SDシリーズ 精密開閉ボールねじ標準在庫品SD series Standardized Bi-directional Ball Screws
1軸で左右開閉、センタリング、精密位置決めが行える経済的なボールねじです。研削ボールねじC3級、C5級を取り揃えています。
SD series are economical Ball Screws which moves bi-directionally with a shaft, and perform centering, precise positioning. There are Precision Ball Screws C3, C5 grade.
●ねじ軸呼び外径とリードの組み合わせ Combination of Shaft nominal dia. & Lead
●精度等級と軸方向すきまSDシリーズ(精密開閉ボールねじ標準在庫品)の精度等級は、C3およびC5(JIB B 1192-3)の2種類です。また軸方向すきまは、精度等級に応じて、0(予圧:C3)および0.005mm以下(C5)を在庫しています。
●呼び番号の構成SDシリーズ(精密開閉ボールねじ標準在庫品)の呼び番号構成は以下のとおりです。
●材質と表面硬度SDシリーズ(精密開閉ボールねじ標準在庫品)は、ねじ軸、ナットともSCM415(浸炭焼入)を採用し、ボールねじ部分の表面硬度はHRC58~62です。
●潤滑SDシリーズ(精密開閉ボールねじ標準在庫品)は、端末未加工状態では、防錆処置のため防錆油を塗布した状態となっています。なお防錆油は潤滑機能がありませんので、ご使用に際しては別途潤滑剤を供給してください。特にご指定のない場合、KSSオリジナルグリース(MSG No.2)を推奨致します。
●軸端形状SDシリーズ(精密開閉ボールねじ標準在庫品)は、軸端形状を標準化していません。軸端の形状を表す図面とともに、KSSへ追加工を依頼してください。
●Accuracy Grade & Axial playAccuracy grades of SD series (Standardized Bi-directional Precision Ball Screws) are 2 kinds, C3 and C5(JIS B 1192-3). Axial play are 0(Preload : C3)and 0.005mm or less(C5) corresponding to accuracy grades in stock.
●Model number notationModel number notation of SD series(Standardized Bi-directional Precision Ball Screws) is as follows.
●Material & Surface hardnessShafts and Nuts of SD series(Standardized Bi-directional Precision Ball Screws) adopts SCM415(carburizing and quenching), surface hardness of Ball Screw part is HRC58-62.
●LubricationSD series(Standardized Bi-directional Precision Ball Screws) are applied with anti-rust oil for rust prevention when unfinished end journal. Since anti-rust oil is not lubricant, apply Grease or lubrication oil before using Ball Screws. If there is no specific instruction, KSS would recommend our original Grease (MSG No.2) as standard lubricant. Please feel free to contact us.
●End-journal profileEnd-journal configuration of SD series (Standardized Bi-directional Precision Ball Screws) is not standardized. Please ask for KSS regarding additional machining with a drawing which shows end-journal profile.
注1)表中の数字は掲載ページを表すNote 1)The number in a table: showing a page in this catalogue.
Leadリード
Shaft dia.呼び外径
1 2
4 A239
6 A240
8 A241 A242
10 A243
12 A244
Unit(単位):mm
① ② ③ ⑨④ ⑤ ⑥ ⑦ ⑧
①開閉ボールねじシリーズ記号②ねじ軸呼び外径(mm)③リード(mm)④左ねじ部長さ(mm)⑤左ねじ記号⑥右ねじ部長さ(mm)⑦右ねじ記号⑧ねじ軸全長(mm)⑨精度等級(C3 or C5)
①Bi-directional Ball Screws series No. ②Screw Shaft nominal diameter(mm)③Lead(mm)④Left-side thread length(mm)⑤Left-hand⑥Right-side thread length(mm)⑦Right-hand⑧Screw Shaft total length(mm)⑨Accuracy grade(C3 or C5)
A239 A240
ボー
ルね
じBall Scresw
標準
在庫
品
SDシ
リー
ズStandard products in stock SD
series
ボー
ルね
じBall Scresw
標準
在庫
品
SDシ
リー
ズStandard products in stock SD
series
Unit(単位):mm
Ball Screw Modelボールねじ型番
Travelストローク
Grade精度
Lead accuracyリード精度
Total Run-out全振れ
Axialplay
軸方向すきま
PreloadTorque予圧トルク
Nm
Basic Load Rating基本定格荷重 N
Travel deviation代表移動量誤差
ep
Variation変動Vu
Dynamic動定格荷重
Ca
Static静定格荷重
Coa
SD0401-50L50R140C3 35 C3 ±0.008 0.008 0.035 0 ~0.010300 430
SD0401-50L50R140C5 35 C5 ±0.018 0.018 0.050 ~0.005 ー
Note 1) Please designate end-journal profile with your sketch. 注1)軸端の追加工は図面とともにご指示ください。Note 2) Absolute position of both Nuts related to the Screw Shaft is not under the control. 注2)ねじ軸に対する左右ナットの絶対位置は管理していません。
Unit(単位):mm
Ball Screw Specifications 諸元
Ball size ボール径 φ0.6
Number of thread 条数 1
Thread direction 巻方向 Left&Right左右
Shaft root dia. ねじ軸谷径 φ3.4
Number of circuit 循環数 1×3
Shaft,Nut material軸、ナット材質 SCM415H
Surface hardnessねじ部表面硬度
HRC58~62(Thread area)
Anti-rust treatment防錆処理
Anti-rust oil防錆油
Non-quenched area / 非焼入部 Non-quenched area / 非焼入部
下表参照see table below
C5:0.010C3:0.008
C5:0.012C3:0.009
GB
B
GG
G
A
A
C5:0.010C3:0.008
C3:0.009C5:0.012
Right / 右ねじLeft / 左ねじ
C0.3
4
PCD 14
11
2-φ2.9
13
(10)3
φ9g
6-0
.005
-0.0
14
φ19
3 0 -0.2
13
φ9g
6-0
.005
-0.0
14
φ19
3
140
105
5050
(5)
φ3.
4
φ3.
4
(10)
C0.3
φ4
C0.5C0.5
(8) 27
View Z-Z矢視 Z-Z
ZZ
ZZ下表参照
see table below
C5:0.010C3:0.008
C5:0.012C3:0.009
G
B
B
GG
G
A
A
C5:0.010C3:0.008
C3:0.009C5:0.012
(11)
C0.5
Right / 右ねじLeft / 左ねじ
φ23 PCD 17
C0.3 φ5.
3
14.5
3.5
13
2-φ3.4
φ11
g6-0
.006
-0.0
17
3.5(11)
14.5
φ23
φ11
g6-0
.006
-0.0
17
φ5.
3
φ6
C0.5
8080
5 0-0.2
(6)
166
210
4
C0.3 C0.3
C0.3
Non-quenched area / 非焼入部 Non-quenched area / 非焼入部
(9) 35View Z-Z矢視 Z-Z
ZZ
ZZ
Standard products in stock SD series標準在庫品 SDシリーズ
SD0401 Shaft dia.(軸径)φ4 Lead(リード)1mm C3&C5
Unit(単位):mm
Ball Screw Modelボールねじ型番
Travelストローク
Grade精度
Lead accuracyリード精度
Total Run-out全振れ
Axialplay
軸方向すきま
PreloadTorque予圧トルク
Nm
Basic Load Rating基本定格荷重 N
Travel deviation代表移動量誤差
ep
Variation変動Vu
Dynamic動定格荷重
Ca
Static静定格荷重
Coa
SD0601-80L80R210C3 65 C3 ±0.008 0.008 0.050 0 ~0.013550 1000
SD0601-80L80R210C5 65 C5 ±0.018 0.018 0.065 ~0.005 ー
Note 1) Please designate end-journal profile with your sketch. 注1)軸端の追加工は図面とともにご指示ください。Note 2) Absolute position of both Nuts related to the Screw Shaft is not under the control. 注2)ねじ軸に対する左右ナットの絶対位置は管理していません。
Unit(単位):mm
Ball Screw Specifications 諸元
Ball size ボール径 φ0.8
Number of thread 条数 1
Thread direction 巻方向 Left&Right左右
Shaft root dia. ねじ軸谷径 φ5.3
Number of circuit 循環数 1×3
Shaft,Nut material軸、ナット材質 SCM415H
Surface hardnessねじ部表面硬度
HRC58~62(Thread area)
Anti-rust treatment防錆処理
Anti-rust oil防錆油
Standard products in stock SD series標準在庫品 SDシリーズ
SD0601 Shaft dia.(軸径)φ6 Lead(リード)1mm C3&C5
A241 A242
ボー
ルね
じBall Scresw
標準
在庫
品
SDシ
リー
ズStandard products in stock SD
series
ボー
ルね
じBall Scresw
標準
在庫
品
SDシ
リー
ズStandard products in stock SD
series
Unit(単位):mm
Ball Screw Modelボールねじ型番
Travelストローク
Grade精度
Lead accuracyリード精度
Total Run-out全振れ
Axialplay
軸方向すきま
PreloadTorque予圧トルク
Nm
Basic Load Rating基本定格荷重 N
Travel deviation代表移動量誤差
ep
Variation変動Vu
Dynamic動定格荷重
Ca
Static静定格荷重
Coa
SD0801-120L120R300C3 105 C3 ±0.010 0.008 0.050 0 ~0.018650 1300
SD0801-120L120R300C5 105 C5 ±0.020 0.018 0.065 ~0.005 ー
Note 1) Please designate end-journal profile with your sketch. 注1)軸端の追加工は図面とともにご指示ください。Note 2) Absolute position of both Nuts related to the Screw Shaft is not under the control. 注2)ねじ軸に対する左右ナットの絶対位置は管理していません。
Unit(単位):mm
Ball Screw Specifications 諸元
Ball size ボール径 φ0.8
Number of thread 条数 1
Thread direction 巻方向 Left&Right左右
Shaft root dia. ねじ軸谷径 φ7.3
Number of circuit 循環数 1×3
Shaft,Nut material軸、ナット材質 SCM415H
Surface hardnessねじ部表面硬度
HRC58~62(Thread area)
Anti-rust treatment防錆処理
Anti-rust oil防錆油
Standard products in stock SD series標準在庫品 SDシリーズ
SD0801 Shaft dia.(軸径)φ8 Lead(リード)1mm C3&C5
Unit(単位):mm
Ball Screw Modelボールねじ型番
Travelストローク
Grade精度
Lead accuracyリード精度
Total Run-out全振れ
Axialplay
軸方向すきま
PreloadTorque予圧トルク
Nm
Basic Load Rating基本定格荷重 N
Travel deviation代表移動量誤差
ep
Variation変動Vu
Dynamic動定格荷重
Ca
Static静定格荷重
Coa
SD0802-120L120R300C3 100 C3 ±0.010 0.008 0.050 0 ~0.0201300 2300
SD0802-120L120R300C5 100 C5 ±0.020 0.018 0.065 ~0.005 ー
Note 1) Please designate end-journal profile with your sketch. 注1)軸端の追加工は図面とともにご指示ください。Note 2) Absolute position of both Nuts related to the Screw Shaft is not under the control. 注2)ねじ軸に対する左右ナットの絶対位置は管理していません。
Unit(単位):mm
Ball Screw Specifications 諸元
Ball size ボール径 φ1.2
Number of thread 条数 1
Thread direction 巻方向 Left&Right左右
Shaft root dia. ねじ軸谷径 φ7.0
Number of circuit 循環数 1×3
Shaft,Nut material軸、ナット材質 SCM415H
Surface hardnessねじ部表面硬度
HRC58~62(Thread area)
Anti-rust treatment防錆処理
Anti-rust oil防錆油
Standard products in stock SD series標準在庫品 SDシリーズ
SD0802 Shaft dia.(軸径)φ8 Lead(リード)2mm C3&C5
下表参照
C5:0.010C3:0.008
C5:0.012C3:0.009
see table below
G
B
B
GG
G
A
A
C5:0.010C3:0.008
C5:0.012C3:0.009
PCD 20φ
26
φ13
g6-0
.006
-0.0
17
15 15
(11)
φ26
φ13
g6-0
.006
-0.0
17
C0.5
(11)
C0.5
φ8
30° 30°
4-φ3.4
4 4 Right / 右ねじ
17120 (10)
Left / 左ねじ
120
250
300
φ6.
3
C0.5 C0.3
C0.3C0.5 φ
6.3
7 0-0.2
6
View Z-Z矢視 Z-Z
ZZ
ZZ
Non-quenched area / 非焼入部 Non-quenched area / 非焼入部
(10) 40
下表参照
C5:0.010C3:0.008
C5:0.012C3:0.009
see table below
G
B
B
GG
G
A
A
C5:0.010C3:0.008
C5:0.012C3:0.009
PCD 20
φ26
φ13
g6-0
.006
-0.0
17
15 15
(11)
φ26
φ13
g6-0
.006
-0.0
17
C0.5
(11)
C0.5
φ8
30° 30°
4-φ3.4
4 4 Right / 右ねじ
17120 (10)
Left / 左ねじ
120
250
300
φ6.
3
C0.5 C0.3
C0.3C0.5 φ
6.3
7 0-0.2
6
View Z-Z矢視 Z-Z
ZZ
ZZ
Non-quenched area / 非焼入部 Non-quenched area / 非焼入部
(10) 40
下表参照
C5:0.010C3:0.008
C5:0.012C3:0.009
see table below
G
B
B
GG
G
A
A
C5:0.010C3:0.008
C5:0.012C3:0.009
φ8
Right / 右ねじ
120 (10)
Left / 左ねじ
120
250
300
φ6.
3
C0.5 C0.3
C0.3C0.5 φ
6.3
7 0-0.2
6
C0.5
4
φ15
g6-0
.006
-0.0
17
PCD 22
4-φ3.4
30°30°
19
18
(14)
φ28
18
φ28
(14) 4
φ15
g6-0
.006
-0.0
17
C0.5
Non-quenched area / 非焼入部 Non-quenched area / 非焼入部
(10) 40
View矢視 Z-Z Z-Z
ZZ
ZZ
下表参照
C5:0.010C3:0.008
C5:0.012C3:0.009
see table below
G
B
B
GG
G
A
A
C5:0.010C3:0.008
C5:0.012C3:0.009
φ8
Right / 右ねじ
120 (10)
Left / 左ねじ
120
250
300
φ6.
3
C0.5 C0.3
C0.3C0.5 φ
6.3
7 0-0.2
6
C0.5
4
φ15
g6-0
.006
-0.0
17
PCD 22
4-φ3.4
30°30°
19
18
(14)
φ28
18
φ28
(14) 4
φ15
g6-0
.006
-0.0
17
C0.5
Non-quenched area / 非焼入部 Non-quenched area / 非焼入部
(10) 40
View矢視 Z-Z Z-Z
ZZ
ZZ
A243 A244
ボー
ルね
じBall Scresw
標準
在庫
品
SDシ
リー
ズStandard products in stock SD
series
ボー
ルね
じBall Scresw
標準
在庫
品
SDシ
リー
ズStandard products in stock SD
series
Unit(単位):mm
Ball Screw Modelボールねじ型番
Travelストローク
Grade精度
Lead accuracyリード精度
Total Run-out全振れ
Axialplay
軸方向すきま
PreloadTorque予圧トルク
Nm
Basic Load Rating基本定格荷重 N
Travel deviation代表移動量誤差
ep
Variation変動Vu
Dynamic動定格荷重
Ca
Static静定格荷重
Coa
SD1002-165L165R400C3 145 C3 ±0.010 0.008 0.050 0 ~0.0251450 3000
SD1002-165L165R400C5 145 C5 ±0.020 0.018 0.065 ~0.005 ー
Note 1) Please designate end-journal profile with your sketch. 注1)軸端の追加工は図面とともにご指示ください。Note 2) Absolute position of both Nuts related to the Screw Shaft is not under the control. 注2)ねじ軸に対する左右ナットの絶対位置は管理していません。
Unit(単位):mm
Ball Screw Specifications 諸元
Ball size ボール径 φ1.2
Number of thread 条数 1
Thread direction 巻方向 Left&Right左右
Shaft root dia. ねじ軸谷径 φ9.0
Number of circuit 循環数 1×3
Shaft,Nut material軸、ナット材質 SCM415H
Surface hardnessねじ部表面硬度
HRC58~62(Thread area)
Anti-rust treatment防錆処理
Anti-rust oil防錆油
Standard products in stock SD series標準在庫品 SDシリーズ
SD1002 Shaft dia.(軸径)φ10 Lead(リード)2mm C3&C5
Unit(単位):mm
Ball Screw Modelボールねじ型番
Travelストローク
Grade精度
Lead accuracyリード精度
Total Run-out全振れ
Axialplay
軸方向すきま
PreloadTorque予圧トルク
Nm
Basic Load Rating基本定格荷重 N
Travel deviation代表移動量誤差
ep
Variation変動Vu
Dynamic動定格荷重
Ca
Static静定格荷重
Coa
SD1202-180L180R440C3 160 C3 ±0.010 0.008 0.065 0 ~0.0351600 3700
SD1202-180L180R440C5 160 C5 ±0.020 0.018 0.080 ~0.005 ー
Note 1) Please designate end-journal profile with your sketch. 注1)軸端の追加工は図面とともにご指示ください。Note 2) Absolute position of both Nuts related to the Screw Shaft is not under the control. 注2)ねじ軸に対する左右ナットの絶対位置は管理していません。
Unit(単位):mm
Ball Screw Specifications 諸元
Ball size ボール径 φ1.2
Number of thread 条数 1
Thread direction 巻方向 Left&Right左右
Shaft root dia. ねじ軸谷径 φ11.0
Number of circuit 循環数 1×3
Shaft,Nut material軸、ナット材質 SCM415H
Surface hardnessねじ部表面硬度
HRC58~62(Thread area)
Anti-rust treatment防錆処理
Anti-rust oil防錆油
Standard products in stock SD series標準在庫品 SDシリーズ
SD1202 Shaft dia.(軸径)φ12 Lead(リード)2mm C3&C5
下表参照
see table below
C5:0.012C3:0.009
G
G
B
B
G
A
G
A
C5:0.010C3:0.008
C5:0.010C3:0.008
C3:0.009C5:0.012
Right / 右ねじLeft / 左ねじ
5
φ34
φ17
g6-0
.006
-0.0
17
21
PCD 26
C0.5
φ10φ34
φ17
g6-0
.006
-0.0
17
C0.5
30°
19
(14)30°
340
165 165(10)
4-φ4.5(14) 5
19
φ8.
3
400
C0.5 C0.3
C0.5C0.3
φ8.
3
8 0-0.2
6
Non-quenched area / 非焼入部
50View Z-Z矢視 Z-Z
ZZ
ZZ
Non-quenched area / 非焼入部
(10)
下表参照
see table below
C5:0.012C3:0.009
G
G
B
B
G
A
G
A
C5:0.010C3:0.008
C5:0.010C3:0.008
C3:0.009C5:0.012
Right / 右ねじLeft / 左ねじ
5
φ34
φ17
g6-0
.006
-0.0
17
21
PCD 26
C0.5
φ10φ34
φ17
g6-0
.006
-0.0
17
C0.5
30°
19
(14)30°
340
165 165(10)
4-φ4.5(14) 5
19
φ8.
3
400
C0.5 C0.3
C0.5C0.3
φ8.
3
8 0-0.2
6
Non-quenched area / 非焼入部
50View Z-Z矢視 Z-Z
ZZ
ZZ
Non-quenched area / 非焼入部
(10)
下表参照see table below
G
G
B
G
BA
G
A
C5:0.012C3:0.009
C5:0.010C3:0.008
C3:0.009C5:0.012
C3:0.008C5:0.010
C0.5C0.5
370
180 180(10)
Right / 右ねじLeft / 左ねじ
C0.5
C0.3
C0.5C0.3
19
(14)
19
(14)
φ19
g6-0
.007
-0.0
20
φ36
PCD 28
23
30°
4-φ4.5
30°
10 0-0.2
8
φ10
.3
φ12
φ19
g6-0
.007
-0.0
20
φ36
φ10
.3
440
55
Non-quenched area / 非焼入部
(15)View Z-Z矢視 Z-Z
ZZ
ZZ
Non-quenched area / 非焼入部
55
下表参照see table below
G
G
B
G
BA
G
A
C5:0.012C3:0.009
C5:0.010C3:0.008
C3:0.009C5:0.012
C3:0.008C5:0.010
C0.5C0.5
370
180 180(10)
Right / 右ねじLeft / 左ねじ
C0.5
C0.3
C0.5C0.3
19
(14)
19
(14)
φ19
g6-0
.007
-0.0
20
φ36
PCD 28
23
30°
4-φ4.5
30°
10 0-0.2
8
φ10
.3
φ12
φ19
g6-0
.007
-0.0
20
φ36
φ10
.3
440
55
Non-quenched area / 非焼入部
(15)View Z-Z矢視 Z-Z
ZZ
ZZ
Non-quenched area / 非焼入部
55
A245 A246
ボー
ルね
じBall Scresw
標準
在庫
品
SR/SSRシリ
ーズ
Standard products in stock SR/SSR series
ボー
ルね
じBall Scresw
標準
在庫
品
SR/SSRシリ
ーズ
Standard products in stock SR/SSR series
200 C7SR 06 01 200 Rー
SR/SSR シリーズ 転造ボールねじ標準在庫品SR/SSR series Standardized Rolled Ball Screws
転造ボールねじCt7級、Ct10級を標準在庫品として取り揃えています。安価な設計をご要望の場合に最適で、軸端末に加工を施せば、短納期で調達できます。またステンレス材を使用したステンレス転造ボールねじシリーズもご利用ください。
●精度等級と軸方向すきまSRシリーズ(転造ボールねじ標準在庫品)およびSSRシリーズ(ステンレス転造ボールねじ標準在庫品)の精度等級は、Ct7およびCt10(JIS B 1192-3)の2種類です。また軸方向すきまは、精度等級に応じて、0.020mm以下(Ct7)および0.050mm以下(Ct10)を在庫しています。
●材質と表面硬度SRシリーズ(転造ボールねじ標準在庫品)およびSSRシリーズ(ステンレス転造ボールねじ標準在庫品)の材質と表面硬度は以下のとおりです。
●潤 滑SRシリーズ(転造ボールねじ標準在庫品)およびSSRシリーズ(ステンレス転造ボールねじ標準在庫品)は、端末未加工状態では、防錆処置のため防錆油を塗布しています。なお防錆油は潤滑機能がありませんので、ご使用に際しては別途潤滑剤を供給してください。特にご指定のない場合、KSSオリジナルグリース(MSG No.2)を推奨いたします。
●その他SRシリーズ(転造ボールねじ標準在庫品)およびSSRシリーズ(ステンレス転造ボールねじ標準在庫品)は軸端形状は標準化していません。ご照会に際しては、お客様より仕様図をいただき、KSSにて追加工いたします。また、固定側軸端がねじ軸外径より太く設計できる「つば付き転造ボールねじ」(下図参照)もシリーズ化していますので、ページ A285をご参照いただくか、KSSまでご照会ください。
●Accuracy Grade & Axial playAccuracy grade of SR series (Standardized Rolled Ball Screws) and SSR series (Standardized Stainless Rolled Ball Screws) are based on Ct7 and Ct10(JIS B 1192-3). According to accuracy grade, Axial play 0.020mm or less (Ct7) and 0.050mm or less (Ct10) are in stock.
●Material & Surface hardnessMaterials and Surface hardness of SR series (Standardized Rolled Ball Screws) and SSR series (Standardized Stainless Rolled Ball Screws) are as follows.
●LubricationSR series (Standardized Rolled Ball Screws) and SSR series (Standardized Stainless Rolled Ball Screws) without end-journal machining are applied with anti-rust oil for rust prevention. Anti-rust oil does not have lubricating function so that please apply the Grease or lubrication oil when using the Ball Screws. If there is no specific instruction, KSS would recommend our original Grease (MSG No.2) as standard lubricant. Please feel free to contact us.
●OthersEnd-journal configuration of SR series (Standardized Rolled Ball Screws) and SSR series (Standardized stainless Rolled Ball Screws) are not standardized. When you request additional machining, please send us a drawing with end-journal profile.Rolled Ball Screws with Integrated end-journal, which is bigger Bearing face than supported seat, are available (SRT/SSRT series) as shown below.Please refer to page A285 or ask KSS.
Rolled Ball Screws with accuracy Ct7 and Ct10 are available in stock. It is suitable for low cost design. Rolled Ball Screws with end-journal machining are available for short delivery.Stainless Rolled Ball Screws are also available.
●ねじ軸呼び外径とリードの組み合わせ Combination of Shaft nominal dia. & Lead
●呼び番号の構成 Model number notation
注1)赤色で示した型番はステンレス転造の対応が可能です。注2)表中の数字は、掲載ページを表す。
つば部分がボールねじ外径より太く設定可能Flanged end-journal for Bearing seat.
Leadリード
Shaft dia.呼び外径
1 2 2.5 4 5 6 8 10 12 15 20
4 A247A248 A249
5 A250
6A251A252A281
A253 A254 A255
8A256A257A282
A258A259A283
A260 A261 A262 A263 A264
10A265A266A284
A267 A268 A269 A270 A271
12 A272A273 A274
14 A275 A276
15 A277 A278 A279
Products製品種別
Material材質
Heat treatment熱処理
Surface hardnessねじ部の表面硬度
Rolled Ball Screws(SR series)一般転造(SRシリーズ)
Shaft/ねじ軸:SCM415S55CSUJ2
Carburizing 浸炭焼き入れInduction Hardening 高周波焼き入れQuench & Temper 焼き入れ焼き戻し HRC58 or more
HRC58以上Nut / ナット:SCM415 Carburizing and Quenching
浸炭焼き入れ
Stainless Rolled Ball Screws(SSR series)
ステンレス転造 (SSRシリーズ)
Shaft/ねじ軸:SUS440C Induction hardening高周波焼き入れ
HRC55 or moreHRC55以上
Nut / ナット:SUS440C Vacuum hardening真空焼き入れ
Unit(単位):mm
①シリーズ記号SR :転造ボールねじSSR :ステンレス転造ボールねじ②ねじ軸呼び外径(mm) ③リード(mm)④ナット形式無記号 : 一般K : コンパクトタイプ⑤ねじ部長さ(mm)⑥巻方向(R=右ねじ)⑦ねじ軸全長(mm) ⑧精度等級(C7 or C10)
① Rolled Ball Screws Series No. SR : Rolled Ball ScrewsSSR : Stainless Rolled Ball Screws②Screw Shaft nominal diameter(mm) ③Lead(mm)④Ball Nut type
None : StandardK : Compact type⑤Screw thread length(mm)⑥Thread direction(R=Right-hand)⑦Screw Shaft total length(mm) ⑧Accuracy grade(C7 or C10)
① ② ③ ⑤ ⑥ ⑦ ⑧K④
Note 1)The models marked red are available for Stainless Rolled Ball Screws. Note 2)The numbers in a table : showing a page in this catalogue.
●精密転造ボールねじ転造ボールねじで高精度(JIS C5)を実現した転造ボールねじ(PSR/PSRTシリーズ)も製作可能です。ページA319を参照ください。
●Precision Rolled Ball ScrewsHigh accuracy(JIS C5) can be produced by Rolled process, what we call Precision Rolled Ball Screws(PSR/PSRT series). Please see page A319.
A247 A248
ボー
ルね
じBall Scresw
標準
在庫
品
SR/SSRシリ
ーズ
Standard products in stock SR/SSR series
ボー
ルね
じBall Scresw
標準
在庫
品
SR/SSRシリ
ーズ
Standard products in stock SR/SSR series
Unit(単位):mm
Ball Screw Modelボールねじ型番
Travelストローク
Grade精度
Shaft lengthねじ軸長さ
Lead accuracyリード精度 Total
Run-out全振れ
Axialplay
軸方向すきま
PreloadTorque予圧トルク
Nm
Basic Load Rating基本定格荷重 N
L1 L2
Travel deviation代表移動量誤差
ep
Variation変動V300
Dynamic動定格荷重
Ca
Static静定格荷重
Coa
SR0401-250R250C7 180 Ct7 200 250 ±0.03 ー 0.200 ~0.020ー 560 790
SR0401-250R250C10 180 Ct10 200 250 ±0.14 ー 0.400 ~0.050
Note)Please designate end-journal profile with your sketch. 注)軸端の追加工は図面とともにご指示ください。
Unit(単位):mm
Ball Screw Specifications 諸元
Ball size ボール径 φ0.8
Number of thread 条数 1
Thread direction 巻方向 Right 右
Shaft root dia. ねじ軸谷径 φ3.3
Number of circuit 循環数 3.7×1
Shaft, Nut material軸、ナット材質 SCM415H
Surface hardnessねじ部表面硬度
HRC58~62(Thread area)
Anti-rust treatment防錆処理
Anti-rust oil防錆油
Standard products in stock SR series標準在庫品 SRシリーズ
SR0401 Shaft dia.(軸径)φ4 Lead(リード)1mm Ct7&Ct10
see table below(13)4
C0.5
17
φ11-
0.05
-0.
10
4-φ3.4
30°
15
30°
(φ
3.85)
PCD 17
φ23
L2
(25)(25) L1(Accuracy guaranteed area/精度保証範囲)
下表参照 E-F
FE
Unit(単位):mm
Ball Screw Modelボールねじ型番
Travelストローク
Grade精度
Shaft lengthねじ軸長さ
Lead accuracyリード精度 Total
Run-out全振れ
Axialplay
軸方向すきま
PreloadTorque予圧トルク
Nm
Basic Load Rating基本定格荷重 N
L1 L2
Travel deviation代表移動量誤差
ep
Variation変動V300
Dynamic動定格荷重
Ca
Static静定格荷重
Coa
SR0401K-100R100C7 80 Ct7 100 ー ±0.02 ー 0.080 ~0.020ー 300 430
SR0401K-100R100C10 80 Ct10 100 ー ±0.07 ー 0.160 ~0.050
Note)Please designate end-journal profile with your sketch. 注)軸端の追加工は図面とともにご指示ください。
Unit(単位):mm
Ball Screw Specifications 諸元
Ball size ボール径 φ0.6
Number of thread 条数 1
Thread direction 巻方向 Right 右
Shaft root dia. ねじ軸谷径 φ3.4
Number of circuit 循環数 1×3
Material材質
Shaft 軸 S55C
Nut ナット SCM415H
Surface hardnessねじ部表面硬度
HRC58~(Thread area)
Anti-rust treatment防錆処理
Anti-rust oil防錆油
Standard products in stock SR series標準在庫品 SRシリーズ
SR0401K Shaft dia.(軸径)φ4 Lead(リード)1mm Ct7&Ct10
(10)3
C0.5
13
φ9-
0.05
-0.
10
4-φ2.9
30°
13
30°
(φ
3.95)
PCD 14
φ19
L1(Accuracy guaranteed area/精度保証範囲)
FE
E-F下表参照see table below
Compact Nut / コンパクトナット
A249 A250
ボー
ルね
じBall Scresw
標準
在庫
品
SR/SSRシリ
ーズ
Standard products in stock SR/SSR series
ボー
ルね
じBall Scresw
標準
在庫
品
SR/SSRシリ
ーズ
Standard products in stock SR/SSR series
Unit(単位):mm
Ball Screw Modelボールねじ型番
Travelストローク
Grade精度
Shaft lengthねじ軸長さ
Lead accuracyリード精度 Total
Run-out全振れ
Axialplay
軸方向すきま
PreloadTorque予圧トルク
Nm
Basic Load Rating基本定格荷重 N
L1 L2
Travel deviation代表移動量誤差
ep
Variation変動V300
Dynamic動定格荷重
Ca
Static静定格荷重
Coa
SR0402-250R250C7 180 Ct7 200 250 ±0.03 ー 0.200 ~0.020ー 420 570
SR0402-250R250C10 180 Ct10 200 250 ±0.14 ー 0.400 ~0.050
Note)Please designate end-journal profile with your sketch. 注)軸端の追加工は図面とともにご指示ください。
Unit(単位):mm
Ball Screw Specifications 諸元
Ball size ボール径 φ0.8
Number of thread 条数 1
Thread direction 巻方向 Right 右
Shaft root dia. ねじ軸谷径 φ3.3
Number of circuit 循環数 2.7×1
Shaft, Nut material軸、ナット材質 SCM415H
Surface hardnessねじ部表面硬度
HRC58~62(Thread area)
Anti-rust treatment防錆処理
Anti-rust oil防錆油
Standard products in stock SR series標準在庫品 SRシリーズ
SR0402 Shaft dia.(軸径)φ4 Lead(リード)2mm Ct7&Ct10
Unit(単位):mm
Ball Screw Modelボールねじ型番
Travelストローク
Grade精度
Shaft lengthねじ軸長さ
Lead accuracyリード精度 Total
Run-out全振れ
Axialplay
軸方向すきま
PreloadTorque予圧トルク
Nm
Basic Load Rating基本定格荷重 N
L1 L2
Travel deviation代表移動量誤差
ep
Variation変動V300
Dynamic動定格荷重
Ca
Static静定格荷重
Coa
SR0504-250R250C7 175 Ct7 200 250 ±0.03 ー 0.120 ~0.020ー 470 720
SR0504-250R250C10 175 Ct10 200 250 ±0.14 ー 0.240 ~0.050
Note)Please designate end-journal profile with your sketch. 注)軸端の追加工は図面とともにご指示ください。
Unit(単位):mm
Ball Screw Specifications 諸元
Ball size ボール径 φ0.8
Number of thread 条数 1
Thread direction 巻方向 Right 右
Shaft root dia. ねじ軸谷径 φ4.3
Number of circuit 循環数 2.7×1
Shaft, Nut material軸、ナット材質 SCM415H
Surface hardnessねじ部表面硬度
HRC58~62(Thread area)
Anti-rust treatment防錆処理
Anti-rust oil防錆油
Standard products in stock SR series標準在庫品 SRシリーズ
SR0504 Shaft dia.(軸径)φ5 Lead(リード)4mm Ct7&Ct10
see table below
4-φ3.4
30°
15
30°
PCD 17
L2
(25)(25) L1(Accuracy guaranteed area/精度保証範囲)
4
φ11-
0.05
-0.
10
19
(15)
(φ
3.85)
φ23
C0.5
F
E-F下表参照
Esee table below
L2
(25)(25) L1(Accuracy guaranteed area/精度保証範囲)
4
φ12-
0.05
-0.
10
PCD 18
22
(18)4-φ3.4
30°
16
φ24(φ
4.85)
C0.5
30°
F
E-F下表参照
E
A251 A252
ボー
ルね
じBall Scresw
標準
在庫
品
SR/SSRシリ
ーズ
Standard products in stock SR/SSR series
ボー
ルね
じBall Scresw
標準
在庫
品
SR/SSRシリ
ーズ
Standard products in stock SR/SSR series
Unit(単位):mm
Ball Screw Modelボールねじ型番
Travelストローク
Grade精度
Shaft lengthねじ軸長さ
Lead accuracyリード精度 Total
Run-out全振れ
Axialplay
軸方向すきま
PreloadTorque予圧トルク
Nm
Basic Load Rating基本定格荷重 N
L1 L2
Travel deviation代表移動量誤差
ep
Variation変動V300
Dynamic動定格荷重
Ca
Static静定格荷重
Coa
SR0601K-200R200C7 175 Ct7 200 ー ±0.03 ー 0.080 ~0.020ー 560 950
SR0601K-200R200C10 175 Ct10 200 ー ±0.14 ー 0.160 ~0.050
Note)Please designate end-journal profile with your sketch. 注)軸端の追加工は図面とともにご指示ください。
Unit(単位):mm
Ball Screw Specifications 諸元
Ball size ボール径 φ0.8
Number of thread 条数 1
Thread direction 巻方向 Right 右
Shaft root dia. ねじ軸谷径 φ5.3
Number of circuit 循環数 1×3
material材質
Shaft 軸 S55C
Nut ナット SCM415H
Surface hardnessねじ部表面硬度
HRC58~(Thread area)
Anti-rust treatment防錆処理
Anti-rust oil防錆油
Standard products in stock SR series標準在庫品 SRシリーズ
SR0601K Shaft dia.(軸径)φ6 Lead(リード)1mm Ct7&Ct10
see table below
(11)3.5
C0.5
φ11-
0.05
-0.
10
PCD 17
15
30°
14.5
φ23
(φ
5.9)
4-φ3.4
30°
L1(Accuracy guaranteed area/精度保証範囲)
F
E-F下表参照
E
Compact Nut / コンパクトナット
Unit(単位):mm
Ball Screw Modelボールねじ型番
Travelストローク
Grade精度
Shaft lengthねじ軸長さ
Lead accuracyリード精度 Total
Run-out全振れ
Axialplay
軸方向すきま
PreloadTorque予圧トルク
Nm
Basic Load Rating基本定格荷重 N
L1 L2
Travel deviation代表移動量誤差
ep
Variation変動V300
Dynamic動定格荷重
Ca
Static静定格荷重
Coa
SR0601-300R300C7 230 Ct7 250 300 ±0.04 ー 0.120 ~0.020ー 680 1200
SR0601-300R300C10 230 Ct10 250 300 ±0.17 ー 0.240 ~0.050
Note)Please designate end-journal profile with your sketch. 注)軸端の追加工は図面とともにご指示ください。
Unit(単位):mm
Ball Screw Specifications 諸元
Ball size ボール径 φ0.8
Number of thread 条数 1
Thread direction 巻方向 Right 右
Shaft root dia. ねじ軸谷径 φ5.3
Number of circuit 循環数 3.7×1
Shaft, Nut material軸、ナット材質 SCM415H
Surface hardnessねじ部表面硬度
HRC58~62(Thread area)
Anti-rust treatment防錆処理
Anti-rust oil防錆油
Standard products in stock SR series標準在庫品 SRシリーズ
SR0601 Shaft dia.(軸径)φ6 Lead(リード)1mm Ct7&Ct10
see table below
(13)4
C0.5
φ13-
0.05
-0.
10
PCD 20
16
30°
17
φ26
(φ
5.85)
4-φ3.4
30°
L2
L1(Accuracy guaranteed area/精度保証範囲)(25) (25)
F
E-F下表参照
E
*Please refer to page A281 for stainless steel type.※ステンレスタイプはぺージA281をご参照ください。
A253 A254
ボー
ルね
じBall Scresw
標準
在庫
品
SR/SSRシリ
ーズ
Standard products in stock SR/SSR series
ボー
ルね
じBall Scresw
標準
在庫
品
SR/SSRシリ
ーズ
Standard products in stock SR/SSR series
Unit(単位):mm
Ball Screw Modelボールねじ型番
Travelストローク
Grade精度
Shaft lengthねじ軸長さ
Lead accuracyリード精度 Total
Run-out全振れ
Axialplay
軸方向すきま
PreloadTorque予圧トルク
Nm
Basic Load Rating基本定格荷重 N
L1 L2
Travel deviation代表移動量誤差
ep
Variation変動V300
Dynamic動定格荷重
Ca
Static静定格荷重
Coa
SR0602-300R300C7 230 Ct7 250 300 ±0.04 ー 0.120 ~0.020ー 750 1200
SR0602-300R300C10 230 Ct10 250 300 ±0.17 ー 0.240 ~0.050
Note)Please designate end-journal profile with your sketch. 注)軸端の追加工は図面とともにご指示ください。
Unit(単位):mm
Ball Screw Specifications 諸元
Ball size ボール径 φ1.0
Number of thread 条数 1
Thread direction 巻方向 Right 右
Shaft root dia. ねじ軸谷径 φ5.1
Number of circuit 循環数 2.7×1
Shaft, Nut material軸、ナット材質 SCM415H
Surface hardnessねじ部表面硬度
HRC58~62(Thread area)
Anti-rust treatment防錆処理
Anti-rust oil防錆油
Standard products in stock SR series標準在庫品 SRシリーズ
SR0602 Shaft dia.(軸径)φ6 Lead(リード)2mm Ct7&Ct10
Unit(単位):mm
Ball Screw Modelボールねじ型番
Travelストローク
Grade精度
Shaft lengthねじ軸長さ
Lead accuracyリード精度 Total
Run-out全振れ
Axialplay
軸方向すきま
PreloadTorque予圧トルク
Nm
Basic Load Rating基本定格荷重 N
L1 L2
Travel deviation代表移動量誤差
ep
Variation変動V300
Dynamic動定格荷重
Ca
Static静定格荷重
Coa
SR0606-300R300C7 230 Ct7 250 300 ±0.04 ー 0.120 ~0.020ー 870 1450
SR0606-300R300C10 230 Ct10 250 300 ±0.17 ー 0.240 ~0.050
Note)Please designate end-journal profile with your sketch. 注)軸端の追加工は図面とともにご指示ください。
Unit(単位):mm
Ball Screw Specifications 諸元
Ball size ボール径 φ1.0
Number of thread 条数 2
Thread direction 巻方向 Right 右
Shaft root dia. ねじ軸谷径 φ5.2
Number of circuit 循環数 1.6×2
Shaft, Nut material軸、ナット材質 SCM415H
Surface hardnessねじ部表面硬度
HRC58~62(Thread area)
Anti-rust treatment防錆処理
Anti-rust oil防錆油
Standard products in stock SR series標準在庫品 SRシリーズ
SR0606 Shaft dia.(軸径)φ6 Lead(リード)6mm Ct7&Ct10
see table below
L2
L1(Accuracy guaranteed area/精度保証範囲)(25) (25)
φ15-
0.05
-0.
10
17
(13)4
C0.5(φ
5.8)
PCD 22
30°
φ28
19
30°
4-φ3.4
F
E-F下表参照
E
see table below
L2
L1(Accuracy guaranteed area/精度保証範囲)(25) (25)
30°
4-φ3.4
30°
PCD 21
16
φ14-
0.05
-0.
10
φ27
17
4 (8)
(φ
5.9)
F
E-F下表参照
E
A255 A256
ボー
ルね
じBall Scresw
標準
在庫
品
SR/SSRシリ
ーズ
Standard products in stock SR/SSR series
ボー
ルね
じBall Scresw
標準
在庫
品
SR/SSRシリ
ーズ
Standard products in stock SR/SSR series
Unit(単位):mm
Ball Screw Modelボールねじ型番
Travelストローク
Grade精度
Shaft lengthねじ軸長さ
Lead accuracyリード精度 Total
Run-out全振れ
Axialplay
軸方向すきま
PreloadTorque予圧トルク
Nm
Basic Load Rating基本定格荷重 N
L1 L2
Travel deviation代表移動量誤差
ep
Variation変動V300
Dynamic動定格荷重
Ca
Static静定格荷重
Coa
SR0610-300R300C7 225 Ct7 250 300 ±0.04 ー 0.120 ~0.020ー 950 1600
SR0610-300R300C10 225 Ct10 250 300 ±0.17 ー 0.240 ~0.050
Note)Please designate end-journal profile with your sketch. 注)軸端の追加工は図面とともにご指示ください。
Unit(単位):mm
Ball Screw Specifications 諸元
Ball size ボール径 φ1.2
Number of thread 条数 2
Thread direction 巻方向 Right 右
Shaft root dia. ねじ軸谷径 φ5.0
Number of circuit 循環数 1.2×2
Shaft, Nut material軸、ナット材質 SCM415H
Surface hardnessねじ部表面硬度
HRC58~62(Thread area)
Anti-rust treatment防錆処理
Anti-rust oil防錆油
Standard products in stock SR series標準在庫品 SRシリーズ
SR0610 Shaft dia.(軸径)φ6 Lead(リード)10mm Ct7&Ct10
see table below
L2
L1(Accuracy guaranteed area/精度保証範囲)(25) (25)
φ14-
0.05
-0.
10
(φ
5.9)
4
30° 30°
4-φ3.4
PCD 21
16φ
27
23
(11.5)
F
E-F下表参照
E
Unit(単位):mm
Ball Screw Modelボールねじ型番
Travelストローク
Grade精度
Shaft lengthねじ軸長さ
Lead accuracyリード精度 Total
Run-out全振れ
Axialplay
軸方向すきま
PreloadTorque予圧トルク
Nm
Basic Load Rating基本定格荷重 N
L1 L2
Travel deviation代表移動量誤差
ep
Variation変動V300
Dynamic動定格荷重
Ca
Static静定格荷重
Coa
SR0801-400R400C7 330 Ct7 350 400 ±0.06 0.05 0.120 ~0.020ー 780 1650
SR0801-400R400C10 330 Ct10 350 400 ±0.24 0.21 0.240 ~0.050
Note)Please designate end-journal profile with your sketch. 注)軸端の追加工は図面とともにご指示ください。
Unit(単位):mm
Ball Screw Specifications 諸元
Ball size ボール径 φ0.8
Number of thread 条数 1
Thread direction 巻方向 Right 右
Shaft root dia. ねじ軸谷径 φ7.3
Number of circuit 循環数 3.7×1
Shaft, Nut material軸、ナット材質 SCM415H
Surface hardnessねじ部表面硬度
HRC58~62(Thread area)
Anti-rust treatment防錆処理
Anti-rust oil防錆油
Standard products in stock SR series標準在庫品 SRシリーズ
SR0801 Shaft dia.(軸径)φ8 Lead(リード)1mm Ct7&Ct10
see table below
L2
L1(Accuracy guaranteed area/精度保証範囲)(25) (25)
17
(13)4
C0.5
φ16-
0.05
-0.
10
18
(φ
7.85)
PCD 23
φ29
30°
4-φ3.4
30°E-F下表参照
FE
*Please refer to page A282 for stainless steel type.※ステンレスタイプはぺージA282をご参照ください。
A257 A258
ボー
ルね
じBall Scresw
標準
在庫
品
SR/SSRシリ
ーズ
Standard products in stock SR/SSR series
ボー
ルね
じBall Scresw
標準
在庫
品
SR/SSRシリ
ーズ
Standard products in stock SR/SSR series
Unit(単位):mm
Ball Screw Modelボールねじ型番
Travelストローク
Grade精度
Shaft lengthねじ軸長さ
Lead accuracyリード精度 Total
Run-out全振れ
Axialplay
軸方向すきま
PreloadTorque予圧トルク
Nm
Basic Load Rating基本定格荷重 N
L1 L2
Travel deviation代表移動量誤差
ep
Variation変動V300
Dynamic動定格荷重
Ca
Static静定格荷重
Coa
SR0801K-230R230C7 200 Ct7 230 ー ±0.03 ー 0.080 ~0.020ー 650 1300
SR0801K-230R230C10 200 Ct10 230 ー ±0.16 ー 0.160 ~0.050
Note)Please designate end-journal profile with your sketch. 注)軸端の追加工は図面とともにご指示ください。
Unit(単位):mm
Ball Screw Specifications 諸元
Ball size ボール径 φ0.8
Number of thread 条数 1
Thread direction 巻方向 Right 右
Shaft root dia. ねじ軸谷径 φ7.3
Number of circuit 循環数 1×3
material材質
Shaft 軸 S55C
Nut ナット SCM415H
Surface hardnessねじ部表面硬度
HRC58~(Thread area)
Anti-rust treatment防錆処理
Anti-rust oil防錆油
Standard products in stock SR series標準在庫品 SRシリーズ
SR0801K Shaft dia.(軸径)φ8 Lead(リード)1mm Ct7&Ct10
E
see table below
L1(Accuracy guaranteed area/精度保証範囲)
15
(11)4
C0.5
φ13-
0.05
-0.
10
17
(φ
7.9)
PCD 20
φ26
30°
4-φ3.4
30°E-F下表参照
F
Compact Nut / コンパクトナット
Unit(単位):mm
Ball Screw Modelボールねじ型番
Travelストローク
Grade精度
Shaft lengthねじ軸長さ
Lead accuracyリード精度 Total
Run-out全振れ
Axialplay
軸方向すきま
PreloadTorque予圧トルク
Nm
Basic Load Rating基本定格荷重 N
L1 L2
Travel deviation代表移動量誤差
ep
Variation変動V300
Dynamic動定格荷重
Ca
Static静定格荷重
Coa
SR0802-400R400C7 325 Ct7 350 400 ±0.06 0.05 0.120 ~0.020ー 2400 4100
SR0802-400R400C10 325 Ct10 350 400 ±0.24 0.21 0.240 ~0.050
Note)Please designate end-journal profile with your sketch. 注)軸端の追加工は図面とともにご指示ください。
Unit(単位):mm
Ball Screw Specifications 諸元
Ball size ボール径 φ1.5875
Number of thread 条数 1
Thread direction 巻方向 Right 右
Shaft root dia. ねじ軸谷径 φ6.6
Number of circuit 循環数 3.7×1
Shaft, Nut material軸、ナット材質 SCM415H
Surface hardnessねじ部表面硬度
HRC58~62(Thread area)
Anti-rust treatment防錆処理
Anti-rust oil防錆油
Standard products in stock SR series標準在庫品 SRシリーズ
SR0802 Shaft dia.(軸径)φ8 Lead(リード)2mm Ct7&Ct10
see table below
L2
L1(Accuracy guaranteed area/精度保証範囲)(25) (25)
φ20-
0.05
-0.
10
C0.5
24
(19)5
22
PCD 29
30°
4-φ4.5
30°
(φ
7.7)
φ37
F
E-F下表参照
E
*Please refer to page A283 for stainless steel type.※ステンレスタイプはぺージA283をご参照ください。
A259 A260
ボー
ルね
じBall Scresw
標準
在庫
品
SR/SSRシリ
ーズ
Standard products in stock SR/SSR series
ボー
ルね
じBall Scresw
標準
在庫
品
SR/SSRシリ
ーズ
Standard products in stock SR/SSR series
Unit(単位):mm
Ball Screw Modelボールねじ型番
Travelストローク
Grade精度
Shaft lengthねじ軸長さ
Lead accuracyリード精度 Total
Run-out全振れ
Axialplay
軸方向すきま
PreloadTorque予圧トルク
Nm
Basic Load Rating基本定格荷重 N
L1 L2
Travel deviation代表移動量誤差
ep
Variation変動V300
Dynamic動定格荷重
Ca
Static静定格荷重
Coa
SR0802K-230R230C7 200 Ct7 230 ー ±0.03 ー 0.080 ~0.020ー 1300 2300
SR0802K-230R230C10 200 Ct10 230 ー ±0.16 ー 0.160 ~0.050
Note)Please designate end-journal profile with your sketch. 注)軸端の追加工は図面とともにご指示ください。
Unit(単位):mm
Ball Screw Specifications 諸元
Ball size ボール径 φ1.2
Number of thread 条数 1
Thread direction 巻方向 Right 右
Shaft root dia. ねじ軸谷径 φ7.0
Number of circuit 循環数 1×3
Material材質
Shaft 軸 S55C
Nut ナット SCM415H
Surface hardnessねじ部表面硬度
HRC58~(Thread area)
Anti-rust treatment防錆処理
Anti-rust oil防錆油
Standard products in stock SR series標準在庫品 SRシリーズ
SR0802K Shaft dia.(軸径)φ8 Lead(リード)2mm Ct7&Ct10
Unit(単位):mm
Ball Screw Modelボールねじ型番
Travelストローク
Grade精度
Shaft lengthねじ軸長さ
Lead accuracyリード精度 Total
Run-out全振れ
Axialplay
軸方向すきま
PreloadTorque予圧トルク
Nm
Basic Load Rating基本定格荷重 N
L1 L2
Travel deviation代表移動量誤差
ep
Variation変動V300
Dynamic動定格荷重
Ca
Static静定格荷重
Coa
SR0802.5-400R400C7 330 Ct7 350 400 ±0.06 0.05 0.120 ~0.020ー 1850 3000
SR0802.5-400R400C10 330 Ct10 350 400 ±0.24 0.21 0.240 ~0.050
Note)Please designate end-journal profile with your sketch. 注)軸端の追加工は図面とともにご指示ください。
Unit(単位):mm
Ball Screw Specifications 諸元
Ball size ボール径 φ1.5875
Number of thread 条数 1
Thread direction 巻方向 Right 右
Shaft root dia. ねじ軸谷径 φ6.3
Number of circuit 循環数 2.7×1
Shaft, Nut material軸、ナット材質 SCM415H
Surface hardnessねじ部表面硬度
HRC58~62(Thread area)
Anti-rust treatment防錆処理
Anti-rust oil防錆油
Standard products in stock SR series標準在庫品 SRシリーズ
SR0802.5 Shaft dia.(軸径)φ8 Lead(リード)2.5mm Ct7&Ct10
see table below
L1(Accuracy guaranteed area/精度保証範囲)
φ15-
0.05
-0.
10
C0.5
18
(14)4
19
PCD 22
30°
4-φ3.4
30°
(φ
7.9)
φ28
F
E-F下表参照
E E
see table below
L2
L1(Accuracy guaranteed area/精度保証範囲)(25) (25)
4
φ16-
0.05
-0.
10
C0.5
18
4-φ3.4
30° 30°
PCD 23
φ29
16
(12)
(φ
7.4) F
E-F下表参照
Compact Nut / コンパクトナット
A261 A262
ボー
ルね
じBall Scresw
標準
在庫
品
SR/SSRシリ
ーズ
Standard products in stock SR/SSR series
ボー
ルね
じBall Scresw
標準
在庫
品
SR/SSRシリ
ーズ
Standard products in stock SR/SSR series
Unit(単位):mm
Ball Screw Modelボールねじ型番
Travelストローク
Grade精度
Shaft lengthねじ軸長さ
Lead accuracyリード精度 Total
Run-out全振れ
Axialplay
軸方向すきま
PreloadTorque予圧トルク
Nm
Basic Load Rating基本定格荷重 N
L1 L2
Travel deviation代表移動量誤差
ep
Variation変動V300
Dynamic動定格荷重
Ca
Static静定格荷重
Coa
SR0805-400R400C7 320 Ct7 350 400 ±0.06 0.05 0.120 ~0.020ー 1850 3000
SR0805-400R400C10 320 Ct10 350 400 ±0.24 0.21 0.240 ~0.050
Note)Please designate end-journal profile with your sketch. 注)軸端の追加工は図面とともにご指示ください。
Unit(単位):mm
Ball Screw Specifications 諸元
Ball size ボール径 φ1.5875
Number of thread 条数 1
Thread direction 巻方向 Right 右
Shaft root dia. ねじ軸谷径 φ6.6
Number of circuit 循環数 2.7×1
Shaft, Nut material軸、ナット材質 SCM415H
Surface hardnessねじ部表面硬度
HRC58~62(Thread area)
Anti-rust treatment防錆処理
Anti-rust oil防錆油
Standard products in stock SR series標準在庫品 SRシリーズ
SR0805 Shaft dia.(軸径)φ8 Lead(リード)5mm Ct7&Ct10
Unit(単位):mm
Ball Screw Modelボールねじ型番
Travelストローク
Grade精度
Shaft lengthねじ軸長さ
Lead accuracyリード精度 Total
Run-out全振れ
Axialplay
軸方向すきま
PreloadTorque予圧トルク
Nm
Basic Load Rating基本定格荷重 N
L1 L2
Travel deviation代表移動量誤差
ep
Variation変動V300
Dynamic動定格荷重
Ca
Static静定格荷重
Coa
SR0808-400R400C7 330 Ct7 350 400 ±0.06 0.05 0.120 ~0.020ー 2200 3800
SR0808-400R400C10 330 Ct10 350 400 ±0.24 0.21 0.240 ~0.050
Note)Please designate end-journal profile with your sketch. 注)軸端の追加工は図面とともにご指示ください。
Unit(単位):mm
Ball Screw Specifications 諸元
Ball size ボール径 φ1.5875
Number of thread 条数 2
Thread direction 巻方向 Right 右
Shaft root dia. ねじ軸谷径 φ6.7
Number of circuit 循環数 1.6×2
Shaft, Nut material軸、ナット材質 SCM415H
Surface hardnessねじ部表面硬度
HRC58~62(Thread area)
Anti-rust treatment防錆処理
Anti-rust oil防錆油
Standard products in stock SR series標準在庫品 SRシリーズ
SR0808 Shaft dia.(軸径)φ8 Lead(リード)8mm Ct7&Ct10
E
see table below
L2
L1(Accuracy guaranteed area/精度保証範囲)(25) (25)
(φ
7.8)
φ31
4
PCD 25
30°
20
4-φ3.4
φ18
-0.
05-
0.10
28
(24)
C0.5
30°
F
E-F下表参照see table below
L2
L1(Accuracy guaranteed area/精度保証範囲)(25) (25)
φ31
φ18-
0.05
-0.
10
PCD 25
20
4
4-φ3.4
30° 30°(10)
20
(φ
7.9) F
E-F下表参照
E
A263 A264
ボー
ルね
じBall Scresw
標準
在庫
品
SR/SSRシリ
ーズ
Standard products in stock SR/SSR series
ボー
ルね
じBall Scresw
標準
在庫
品
SR/SSRシリ
ーズ
Standard products in stock SR/SSR series
Unit(単位):mm
Ball Screw Modelボールねじ型番
Travelストローク
Grade精度
Shaft lengthねじ軸長さ
Lead accuracyリード精度 Total
Run-out全振れ
Axialplay
軸方向すきま
PreloadTorque予圧トルク
Nm
Basic Load Rating基本定格荷重 N
L1 L2
Travel deviation代表移動量誤差
ep
Variation変動V300
Dynamic動定格荷重
Ca
Static静定格荷重
Coa
SR0810-400R400C7 325 Ct7 350 400 ±0.06 0.05 0.120 ~0.020ー 2200 3800
SR0810-400R400C10 325 Ct10 350 400 ±0.24 0.21 0.240 ~0.050
Note)Please designate end-journal profile with your sketch. 注)軸端の追加工は図面とともにご指示ください。
Unit(単位):mm
Ball Screw Specifications 諸元
Ball size ボール径 φ1.5875
Number of thread 条数 2
Thread direction 巻方向 Right 右
Shaft root dia. ねじ軸谷径 φ6.7
Number of circuit 循環数 1.6×2
Shaft, Nut material軸、ナット材質 SCM415H
Surface hardnessねじ部表面硬度
HRC58~62(Thread area)
Anti-rust treatment防錆処理
Anti-rust oil防錆油
Standard products in stock SR series標準在庫品 SRシリーズ
SR0810 Shaft dia.(軸径)φ8 Lead(リード)10mm Ct7&Ct10
Unit(単位):mm
Ball Screw Modelボールねじ型番
Travelストローク
Grade精度
Shaft lengthねじ軸長さ
Lead accuracyリード精度 Total
Run-out全振れ
Axialplay
軸方向すきま
PreloadTorque予圧トルク
Nm
Basic Load Rating基本定格荷重 N
L1 L2
Travel deviation代表移動量誤差
ep
Variation変動V300
Dynamic動定格荷重
Ca
Static静定格荷重
Coa
SR0812-400R400C7 320 Ct7 350 400 ±0.06 0.05 0.120 ~0.020ー 2200 4000
SR0812-400R400C10 320 Ct10 350 400 ±0.24 0.21 0.240 ~0.050
Note)Please designate end-journal profile with your sketch. 注)軸端の追加工は図面とともにご指示ください。
Unit(単位):mm
Ball Screw Specifications 諸元
Ball size ボール径 φ1.5875
Number of thread 条数 2
Thread direction 巻方向 Right 右
Shaft root dia. ねじ軸谷径 φ6.7
Number of circuit 循環数 1.6×2
Shaft, Nut material軸、ナット材質 SCM415H
Surface hardnessねじ部表面硬度
HRC58~62(Thread area)
Anti-rust treatment防錆処理
Anti-rust oil防錆油
Standard products in stock SR series標準在庫品 SRシリーズ
SR0812 Shaft dia.(軸径)φ8 Lead(リード)12mm Ct7&Ct10
see table below
L2
L1(Accuracy guaranteed area/精度保証範囲)(25) (25)φ
31
φ18-
0.05
-0.
10
(φ
7.9)
24
(13)430°
PCD 25
20
30°
4-φ3.4
F
E-F下表参照
E
see table below
L2
L1(Accuracy guaranteed area/精度保証範囲)(25) (25)
PCD 25
φ31
φ18-
0.05
-0.
10
20
4
27
(17)30°
4-φ3.4
30°
(φ
7.9) F
E-F下表参照
E
A265 A266
ボー
ルね
じBall Scresw
標準
在庫
品
SR/SSRシリ
ーズ
Standard products in stock SR/SSR series
ボー
ルね
じBall Scresw
標準
在庫
品
SR/SSRシリ
ーズ
Standard products in stock SR/SSR series
Unit(単位):mm
Ball Screw Modelボールねじ型番
Travelストローク
Grade精度
Shaft lengthねじ軸長さ
Lead accuracyリード精度 Total
Run-out全振れ
Axialplay
軸方向すきま
PreloadTorque予圧トルク
Nm
Basic Load Rating基本定格荷重 N
L1 L2
Travel deviation代表移動量誤差
ep
Variation変動V300
Dynamic動定格荷重
Ca
Static静定格荷重
Coa
SR1002K-230R230C7 200 Ct7 230 ー ±0.03 ー 0.080 ~0.020ー 1450 3000
SR1002K-230R230C10 200 Ct10 230 ー ±0.16 ー 0.160 ~0.050
Note)Please designate end-journal profile with your sketch. 注)軸端の追加工は図面とともにご指示ください。
Unit(単位):mm
Ball Screw Specifications 諸元
Ball size ボール径 φ1.2
Number of thread 条数 1
Thread direction 巻方向 Right 右
Shaft root dia. ねじ軸谷径 φ9.0
Number of circuit 循環数 1×3
Material材質
Shaft 軸 S55C
Nut ナット SCM415H
Surface hardnessねじ部表面硬度
HRC58~(Thread area)
Anti-rust treatment防錆処理
Anti-rust oil防錆油
Standard products in stock SR series標準在庫品 SRシリーズ
SR1002K Shaft dia.(軸径)φ10 Lead(リード)2mm Ct7&Ct10
see table below
L1(Accuracy guaranteed area/精度保証範囲)
C0.5
21
30°
PCD 26
φ34(φ
9.9)
19
(14)5
4-φ4.5
30°
φ17-
0.05
-0.
10
F
E-F下表参照
E
Compact Nut / コンパクトナット
Unit(単位):mm
Ball Screw Modelボールねじ型番
Travelストローク
Grade精度
Shaft lengthねじ軸長さ
Lead accuracyリード精度 Total
Run-out全振れ
Axialplay
軸方向すきま
PreloadTorque予圧トルク
Nm
Basic Load Rating基本定格荷重 N
L1 L2
Travel deviation代表移動量誤差
ep
Variation変動V300
Dynamic動定格荷重
Ca
Static静定格荷重
Coa
SR1002-400R400C7 325 Ct7 350 400 ±0.05 0.05 0.080 ~0.020ー 2700 5300
SR1002-400R400C10 325 Ct10 350 400 ±0.24 0.21 0.160 ~0.050
Note)Please designate end-journal profile with your sketch. 注)軸端の追加工は図面とともにご指示ください。
Unit(単位):mm
Ball Screw Specifications 諸元
Ball size ボール径 φ1.5875
Number of thread 条数 1
Thread direction 巻方向 Right 右
Shaft root dia. ねじ軸谷径 φ8.6
Number of circuit 循環数 3.7×1
Shaft, Nut material軸、ナット材質 SCM415H
Surface hardnessねじ部表面硬度
HRC58~62(Thread area)
Anti-rust treatment防錆処理
Anti-rust oil防錆油
Standard products in stock SR series標準在庫品 SRシリーズ
SR1002 Shaft dia.(軸径)φ10 Lead(リード)2mm Ct7&Ct10
see table below
L2
L1(Accuracy guaranteed area/精度保証範囲)(25) (25)
C0.5
25
30°
PCD 32
φ40(φ
9.7)
24
(19)5
4-φ4.5
30°
φ23-
0.05
-0.
10
F
E-F下表参照
E
*Please refer to page A284 for stainless steel type.※ステンレスタイプはぺージA284をご参照ください。
A267 A268
ボー
ルね
じBall Scresw
標準
在庫
品
SR/SSRシリ
ーズ
Standard products in stock SR/SSR series
ボー
ルね
じBall Scresw
標準
在庫
品
SR/SSRシリ
ーズ
Standard products in stock SR/SSR series
Unit(単位):mm
Ball Screw Modelボールねじ型番
Travelストローク
Grade精度
Shaft lengthねじ軸長さ
Lead accuracyリード精度 Total
Run-out全振れ
Axialplay
軸方向すきま
PreloadTorque予圧トルク
Nm
Basic Load Rating基本定格荷重 N
L1 L2
Travel deviation代表移動量誤差
ep
Variation変動V300
Dynamic動定格荷重
Ca
Static静定格荷重
Coa
SR1004-450R450C7 370 Ct7 400 450 ±0.06 0.05 0.120 ~0.020ー 3000 5200
SR1004-450R450C10 370 Ct10 400 450 ±0.28 0.21 0.240 ~0.050
Note)Please designate end-journal profile with your sketch. 注)軸端の追加工は図面とともにご指示ください。
Unit(単位):mm
Ball Screw Specifications 諸元
Ball size ボール径 φ2.0
Number of thread 条数 1
Thread direction 巻方向 Right 右
Shaft root dia. ねじ軸谷径 φ8.2
Number of circuit 循環数 2.7×1
Shaft, Nut material軸、ナット材質 SCM415H
Surface hardnessねじ部表面硬度
HRC58~62(Thread area)
Anti-rust treatment防錆処理
Anti-rust oil防錆油
Standard products in stock SR series標準在庫品 SRシリーズ
SR1004 Shaft dia.(軸径)φ10 Lead(リード)4mm Ct7&Ct10
Unit(単位):mm
Ball Screw Modelボールねじ型番
Travelストローク
Grade精度
Shaft lengthねじ軸長さ
Lead accuracyリード精度 Total
Run-out全振れ
Axialplay
軸方向すきま
PreloadTorque予圧トルク
Nm
Basic Load Rating基本定格荷重 N
L1 L2
Travel deviation代表移動量誤差
ep
Variation変動V300
Dynamic動定格荷重
Ca
Static静定格荷重
Coa
SR1005-450R450C7 370 Ct7 400 450 ±0.06 0.05 0.120 ~0.020ー 3000 5200
SR1005-450R450C10 370 Ct10 400 450 ±0.28 0.21 0.240 ~0.050
Note)Please designate end-journal profile with your sketch. 注)軸端の追加工は図面とともにご指示ください。
Unit(単位):mm
Ball Screw Specifications 諸元
Ball size ボール径 φ2.0
Number of thread 条数 1
Thread direction 巻方向 Right 右
Shaft root dia. ねじ軸谷径 φ8.2
Number of circuit 循環数 2.7×1
Shaft, Nut material軸、ナット材質 SCM415H
Surface hardnessねじ部表面硬度
HRC58~62(Thread area)
Anti-rust treatment防錆処理
Anti-rust oil防錆油
Standard products in stock SR series標準在庫品 SRシリーズ
SR1005 Shaft dia.(軸径)φ10 Lead(リード)5mm Ct7&Ct10
see table below
L2
L1(Accuracy guaranteed area/精度保証範囲)(25) (25)
30°
4-φ4.5
30°
28
(23)5
(φ
9.6)
26
PCD 33 φ41
φ24
-0.
05-
0.10
C1
F
E-F下表参照
E
see table below
L2
L1(Accuracy guaranteed area/精度保証範囲)(25) (25)25
30°
PCD 32
4-φ4.5
30°
26
(21)5
φ40
φ23-
0.05
-0.
10
(φ
9.6)
C0.5
F
E-F下表参照
E
A269 A270
ボー
ルね
じBall Scresw
標準
在庫
品
SR/SSRシリ
ーズ
Standard products in stock SR/SSR series
ボー
ルね
じBall Scresw
標準
在庫
品
SR/SSRシリ
ーズ
Standard products in stock SR/SSR series
Unit(単位):mm
Ball Screw Modelボールねじ型番
Travelストローク
Grade精度
Shaft lengthねじ軸長さ
Lead accuracyリード精度 Total
Run-out全振れ
Axialplay
軸方向すきま
PreloadTorque予圧トルク
Nm
Basic Load Rating基本定格荷重 N
L1 L2
Travel deviation代表移動量誤差
ep
Variation変動V300
Dynamic動定格荷重
Ca
Static静定格荷重
Coa
SR1010-450R450C7 375 Ct7 400 450 ±0.06 0.05 0.120 ~0.020ー 3300 5900
SR1010-450R450C10 375 Ct10 400 450 ±0.28 0.21 0.240 ~0.050
Note)Please designate end-journal profile with your sketch. 注)軸端の追加工は図面とともにご指示ください。
Unit(単位):mm
Ball Screw Specifications 諸元
Ball size ボール径 φ2.0
Number of thread 条数 2
Thread direction 巻方向 Right 右
Shaft root dia. ねじ軸谷径 φ8.4
Number of circuit 循環数 1.6×2
Shaft, Nut material軸、ナット材質 SCM415H
Surface hardnessねじ部表面硬度
HRC58~62(Thread area)
Anti-rust treatment防錆処理
Anti-rust oil防錆油
Standard products in stock SR series標準在庫品 SRシリーズ
SR1010 Shaft dia.(軸径)φ10 Lead(リード)10mm Ct7&Ct10
Unit(単位):mm
Ball Screw Modelボールねじ型番
Travelストローク
Grade精度
Shaft lengthねじ軸長さ
Lead accuracyリード精度 Total
Run-out全振れ
Axialplay
軸方向すきま
PreloadTorque予圧トルク
Nm
Basic Load Rating基本定格荷重 N
L1 L2
Travel deviation代表移動量誤差
ep
Variation変動V300
Dynamic動定格荷重
Ca
Static静定格荷重
Coa
SR1015-450R450C7 365 Ct7 400 450 ±0.06 0.05 0.120 ~0.020ー 3300 6400
SR1015-450R450C10 365 Ct10 400 450 ±0.28 0.21 0.240 ~0.050
Note)Please designate end-journal profile with your sketch. 注)軸端の追加工は図面とともにご指示ください。
Unit(単位):mm
Ball Screw Specifications 諸元
Ball size ボール径 φ2.0
Number of thread 条数 2
Thread direction 巻方向 Right 右
Shaft root dia. ねじ軸谷径 φ8.4
Number of circuit 循環数 1.6×2
Shaft, Nut material軸、ナット材質 SCM415H
Surface hardnessねじ部表面硬度
HRC58~62(Thread area)
Anti-rust treatment防錆処理
Anti-rust oil防錆油
Standard products in stock SR series標準在庫品 SRシリーズ
SR1015 Shaft dia.(軸径)φ10 Lead(リード)15mm Ct7&Ct10
see table below
L2
L1(Accuracy guaranteed area/精度保証範囲)(25) (25)25
30°
PCD 32
5
4-φ4.5
30°
φ40
φ23-
0.05
-0.
10
24
(13)
(φ
9.8)
F
E-F下表参照
E
see table below
L2
L1(Accuracy guaranteed area/精度保証範囲)(25) (25)25
30°
PCD 32
5
4-φ4.5
30°
φ40
φ23-
0.05
-0.
10
33
(22)
(φ
9.8) F
E-F下表参照
E
A271 A272
ボー
ルね
じBall Scresw
標準
在庫
品
SR/SSRシリ
ーズ
Standard products in stock SR/SSR series
ボー
ルね
じBall Scresw
標準
在庫
品
SR/SSRシリ
ーズ
Standard products in stock SR/SSR series
Unit(単位):mm
Ball Screw Modelボールねじ型番
Travelストローク
Grade精度
Shaft lengthねじ軸長さ
Lead accuracyリード精度 Total
Run-out全振れ
Axialplay
軸方向すきま
PreloadTorque予圧トルク
Nm
Basic Load Rating基本定格荷重 N
L1 L2
Travel deviation代表移動量誤差
ep
Variation変動V300
Dynamic動定格荷重
Ca
Static静定格荷重
Coa
SR1020-450R450C7 375 Ct7 400 450 ±0.06 0.05 0.120 ~0.020ー 2100 4000
SR1020-450R450C10 375 Ct10 400 450 ±0.28 0.21 0.240 ~0.050
Note)Please designate end-journal profile with your sketch. 注)軸端の追加工は図面とともにご指示ください。
Unit(単位):mm
Ball Screw Specifications 諸元
Ball size ボール径 φ1.5875
Number of thread 条数 4
Thread direction 巻方向 Right 右
Shaft root dia. ねじ軸谷径 φ8.7
Number of circuit 循環数 0.7×4
Shaft, Nut material軸、ナット材質 SCM415H
Surface hardnessねじ部表面硬度
HRC58~62(Thread area)
Anti-rust treatment防錆処理
Anti-rust oil防錆油
Standard products in stock SR series標準在庫品 SRシリーズ
SR1020 Shaft dia.(軸径)φ10 Lead(リード)20mm Ct7&Ct10
Unit(単位):mm
Ball Screw Modelボールねじ型番
Travelストローク
Grade精度
Shaft lengthねじ軸長さ
Lead accuracyリード精度 Total
Run-out全振れ
Axialplay
軸方向すきま
PreloadTorque予圧トルク
Nm
Basic Load Rating基本定格荷重 N
L1 L2
Travel deviation代表移動量誤差
ep
Variation変動V300
Dynamic動定格荷重
Ca
Static静定格荷重
Coa
SR1202-450R450C7 375 Ct7 400 450 ±0.06 0.05 0.080 ~0.020ー 3000 6400
SR1202-450R450C10 375 Ct10 400 450 ±0.28 0.21 0.160 ~0.050
Note)Please designate end-journal profile with your sketch. 注)軸端の追加工は図面とともにご指示ください。
Unit(単位):mm
Ball Screw Specifications 諸元
Ball size ボール径 φ1.5875
Number of thread 条数 1
Thread direction 巻方向 Right 右
Shaft root dia. ねじ軸谷径 φ10.6
Number of circuit 循環数 3.7×1
Shaft, Nut material軸、ナット材質 SCM415H
Surface hardnessねじ部表面硬度
HRC58~62(Thread area)
Anti-rust treatment防錆処理
Anti-rust oil防錆油
Standard products in stock SR series標準在庫品 SRシリーズ
SR1202 Shaft dia.(軸径)φ12 Lead(リード)2mm Ct7&Ct10
see table below
L2
L1(Accuracy guaranteed area/精度保証範囲)(25) (25)
5
φ37
23
φ20-
0.05
-0.
10
(φ
9.9)
30° 30°
PCD 29
4-φ4.5
22
(13)
F
E-F下表参照
E
see table below
L2
L1(Accuracy guaranteed area/精度保証範囲)(25) (25)27
φ25-
0.05
-0.
10
φ42
PCD 34
C0.5
24
(19)530° 30°
4-φ4.5
(φ
11.7) F
E-F下表参照
E
A273 A274
ボー
ルね
じBall Scresw
標準
在庫
品
SR/SSRシリ
ーズ
Standard products in stock SR/SSR series
ボー
ルね
じBall Scresw
標準
在庫
品
SR/SSRシリ
ーズ
Standard products in stock SR/SSR series
Unit(単位):mm
Ball Screw Modelボールねじ型番
Travelストローク
Grade精度
Shaft lengthねじ軸長さ
Lead accuracyリード精度 Total
Run-out全振れ
Axialplay
軸方向すきま
PreloadTorque予圧トルク
Nm
Basic Load Rating基本定格荷重 N
L1 L2
Travel deviation代表移動量誤差
ep
Variation変動V300
Dynamic動定格荷重
Ca
Static静定格荷重
Coa
SR1202K-280R280C7 250 Ct7 280 ー ±0.04 ー 0.080 ~0.020ー 1600 3700
SR1202K-280R280C10 250 Ct10 280 ー ±0.19 ー 0.160 ~0.050
Note)Please designate end-journal profile with your sketch. 注)軸端の追加工は図面とともにご指示ください。
Unit(単位):mm
Ball Screw Specifications 諸元
Ball size ボール径 φ1.2
Number of thread 条数 1
Thread direction 巻方向 Right 右
Shaft root dia. ねじ軸谷径 φ11.0
Number of circuit 循環数 1×3
material材質
Shaft 軸 S55C
Nut ナット SCM415H
Surface hardnessねじ部表面硬度
HRC58~(Thread area)
Anti-rust treatment防錆処理
Anti-rust oil防錆油
Standard products in stock SR series標準在庫品 SRシリーズ
SR1202K Shaft dia.(軸径)φ12 Lead(リード)2mm Ct7&Ct10
Unit(単位):mm
Ball Screw Modelボールねじ型番
Travelストローク
Grade精度
Shaft lengthねじ軸長さ
Lead accuracyリード精度 Total
Run-out全振れ
Axialplay
軸方向すきま
PreloadTorque予圧トルク
Nm
Basic Load Rating基本定格荷重 N
L1 L2
Travel deviation代表移動量誤差
ep
Variation変動V300
Dynamic動定格荷重
Ca
Static静定格荷重
Coa
SR1210-450R450C7 370 Ct7 400 450 ±0.06 0.05 0.080 ~0.020ー 5100 9800
SR1210-450R450C10 370 Ct10 400 450 ±0.28 0.21 0.160 ~0.050
Note)Please designate end-journal profile with your sketch. 注)軸端の追加工は図面とともにご指示ください。
Unit(単位):mm
Ball Screw Specifications 諸元
Ball size ボール径 φ2.381
Number of thread 条数 2
Thread direction 巻方向 Right 右
Shaft root dia. ねじ軸谷径 φ10.2
Number of circuit 循環数 1.7×2
Shaft, Nut material軸、ナット材質 SCM415H
Surface hardnessねじ部表面硬度
HRC58~62(Thread area)
Anti-rust treatment防錆処理
Anti-rust oil防錆油
Standard products in stock SR series標準在庫品 SRシリーズ
SR1210 Shaft dia.(軸径)φ12 Lead(リード)10mm Ct7&Ct10
see table below
L1(Accuracy guaranteed area/精度保証範囲)
23
φ19-
0.05
-0.
10
φ36
PCD 28
C0.5
19
(14)530° 30°
(φ
11.9) F
E-F下表参照
E
4-φ4.5
see table below
L2
L1(Accuracy guaranteed area/精度保証範囲)(25) (25)
30° 30°
30
6 (14.5)
φ24
-0.
05-
0.10
φ41
26
PCD 33
4-φ4.5
(φ
11.7
5) F
E-F下表参照
E
Compact Nut / コンパクトナット
A275 A276
ボー
ルね
じBall Scresw
標準
在庫
品
SR/SSRシリ
ーズ
Standard products in stock SR/SSR series
ボー
ルね
じBall Scresw
標準
在庫
品
SR/SSRシリ
ーズ
Standard products in stock SR/SSR series
Unit(単位):mm
Ball Screw Modelボールねじ型番
Travelストローク
Grade精度
Shaft lengthねじ軸長さ
Lead accuracyリード精度 Total
Run-out全振れ
Axialplay
軸方向すきま
PreloadTorque予圧トルク
Nm
Basic Load Rating基本定格荷重 N
L1 L2
Travel deviation代表移動量誤差
ep
Variation変動V300
Dynamic動定格荷重
Ca
Static静定格荷重
Coa
SR1402-500R500C7 425 Ct7 450 500 ±0.07 0.05 0.080 ~0.020ー 3200 7500
SR1402-500R500C10 425 Ct10 450 500 ±0.31 0.21 0.160 ~0.050
Note)Please designate end-journal profile with your sketch. 注)軸端の追加工は図面とともにご指示ください。
Unit(単位):mm
Ball Screw Specifications 諸元
Ball size ボール径 φ1.5875
Number of thread 条数 1
Thread direction 巻方向 Right 右
Shaft root dia. ねじ軸谷径 φ12.6
Number of circuit 循環数 3.7×1
Shaft, Nut material軸、ナット材質 SCM415H
Surface hardnessねじ部表面硬度
HRC58~62(Thread area)
Anti-rust treatment防錆処理
Anti-rust oil防錆油
Standard products in stock SR series標準在庫品 SRシリーズ
SR1402 Shaft dia.(軸径)φ14 Lead(リード)2mm Ct7&Ct10
Unit(単位):mm
Ball Screw Modelボールねじ型番
Travelストローク
Grade精度
Shaft lengthねじ軸長さ
Lead accuracyリード精度 Total
Run-out全振れ
Axialplay
軸方向すきま
PreloadTorque予圧トルク
Nm
Basic Load Rating基本定格荷重 N
L1 L2
Travel deviation代表移動量誤差
ep
Variation変動V300
Dynamic動定格荷重
Ca
Static静定格荷重
Coa
SR1404-500R500C7 415 Ct7 450 500 ±0.07 0.05 0.080 ~0.020ー 5700 11600
SR1404-500R500C10 415 Ct10 450 500 ±0.31 0.21 0.160 ~0.050
Note)Please designate end-journal profile with your sketch. 注)軸端の追加工は図面とともにご指示ください。
Unit(単位):mm
Ball Screw Specifications 諸元
Ball size ボール径 φ2.381
Number of thread 条数 1
Thread direction 巻方向 Right 右
Shaft root dia. ねじ軸谷径 φ11.8
Number of circuit 循環数 3.7×1
Shaft, Nut material軸、ナット材質 SCM415H
Surface hardnessねじ部表面硬度
HRC58~62(Thread area)
Anti-rust treatment防錆処理
Anti-rust oil防錆油
Standard products in stock SR series標準在庫品 SRシリーズ
SR1404 Shaft dia.(軸径)φ14 Lead(リード)4mm Ct7&Ct10
see table below
L2
L1(Accuracy guaranteed area/精度保証範囲)(25) (25)
PCD 36
φ45
φ26-
0.05
-0.
10
30° 30°
28
(φ
13.7)
25
(19)6
C0.5
4-φ5.5
F
E-F下表参照
E
下表参照 E-Fsee table below
L2
L1(Accuracy guaranteed area/精度保証範囲)(25) (25)
φ30-
0.05
-0.
10
33
(27)6
φ49
C1
PCD 40
32
30°
4-φ5.5
(φ
13.5)
30°
FE
A277 A278
ボー
ルね
じBall Scresw
標準
在庫
品
SR/SSRシリ
ーズ
Standard products in stock SR/SSR series
ボー
ルね
じBall Scresw
標準
在庫
品
SR/SSRシリ
ーズ
Standard products in stock SR/SSR series
Unit(単位):mm
Ball Screw Modelボールねじ型番
Travelストローク
Grade精度
Shaft lengthねじ軸長さ
Lead accuracyリード精度 Total
Run-out全振れ
Axialplay
軸方向すきま
PreloadTorque予圧トルク
Nm
Basic Load Rating基本定格荷重 N
L1 L2
Travel deviation代表移動量誤差
ep
Variation変動V300
Dynamic動定格荷重
Ca
Static静定格荷重
Coa
SR1505-1000R1000C10 965 Ct10 ― 1000 ±0.7 0.21 0.400 ~0.050 ー 8900 17000
Note)Please designate end-journal profile with your sketch. 注)軸端の追加工は図面とともにご指示ください。
Unit(単位):mm
Ball Screw Specifications 諸元
Ball size ボール径 φ3.175
Number of thread 条数 1
Thread direction 巻方向 Right 右
Shaft root dia. ねじ軸谷径 φ12.2
Number of circuit 循環数 3.7×1
Material材質
Shaft 軸 SUJ2
Nut ナット SCM415
Surface hardnessねじ部表面硬度
HRC58~62(Thread area)
Anti-rust treatment防錆処理
Anti-rust oil防錆油
Unit(単位):mm
Ball Screw Specifications 諸元
Ball size ボール径 φ3.175
Number of thread 条数 2
Thread direction 巻方向 Right 右
Shaft root dia. ねじ軸谷径 φ12.2
Number of circuit 循環数 2.7×2
Material材質
Shaft 軸 SUJ2
Nut ナット SCM415
Surface hardnessねじ部表面硬度
HRC58~62(Thread area)
Anti-rust treatment防錆処理
Anti-rust oil防錆油
Standard products in stock SR series標準在庫品 SRシリーズ
SR1505 Shaft dia.(軸径)φ15 Lead(リード)5mm Ct10
Unit(単位):mm
Ball Screw Modelボールねじ型番
Travelストローク
Grade精度
Shaft lengthねじ軸長さ
Lead accuracyリード精度 Total
Run-out全振れ
Axialplay
軸方向すきま
PreloadTorque予圧トルク
Nm
Basic Load Rating基本定格荷重 N
L1 L2
Travel deviation代表移動量誤差
ep
Variation変動V300
Dynamic動定格荷重
Ca
Static静定格荷重
Coa
SR1510-1000R1000C10 955 Ct10 ― 1000 ±0.7 0.21 0.400 ~0.050 ー 12000 25000
Note)Please designate end-journal profile with your sketch. 注)軸端の追加工は図面とともにご指示ください。
Standard products in stock SR series標準在庫品 SRシリーズ
SR1510 Shaft dia.(軸径)φ15 Lead(リード)10mm Ct10
see table below
M6(Oil hole/給油穴)
L2
PCD 45
φ34-
0.05
-0.
10
(φ
15)
50
34
30°
4-φ5.5φ9.5Depth/深5.5 Facing/ざぐり
30°
φ57
33
(16)11
5.5
F
E-F下表参照
E
see table below
M6(Oil hole/給油穴)
L2
PCD 45
φ34-
0.05
-0.
10
(φ
15)
50
34
30°
4-φ5.5φ9.5Depth/深5.5 Facing/ざぐり
30°
φ57
11
5.5
43
(21)
F
E-F下表参照
E
A279 A280
ボー
ルね
じBall Scresw
標準
在庫
品
SR/SSRシリ
ーズ
Standard products in stock SR/SSR series
ボー
ルね
じBall Scresw
標準
在庫
品
SR/SSRシリ
ーズ
Standard products in stock SR/SSR series
Unit(単位):mm
Ball Screw Modelボールねじ型番
Travelストローク
Grade精度
Shaft lengthねじ軸長さ
Lead accuracyリード精度 Total
Run-out全振れ
Axialplay
軸方向すきま
PreloadTorque予圧トルク
Nm
Basic Load Rating基本定格荷重 N
L1 L2
Travel deviation代表移動量誤差
ep
Variation変動V300
Dynamic動定格荷重
Ca
Static静定格荷重
Coa
SR1520-1000R1000C10 945 Ct10 ― 1000 ±0.7 0.21 0.400 ~0.050 ー 8000 16000
Note)Please designate end-journal profile with your sketch. 注)軸端の追加工は図面とともにご指示ください。
Standard products in stock SR series標準在庫品 SRシリーズ
SR1520 Shaft dia.(軸径)φ15 Lead(リード)20mm Ct10
Unit(単位):mm
Ball Screw Specifications 諸元
Ball size ボール径 φ3.175
Number of thread 条数 2
Thread direction 巻方向 Right 右
Shaft root dia. ねじ軸谷径 φ12.7
Number of circuit 循環数 1.7×2
Material材質
Shaft 軸 SUJ2
Nut ナット SCM415
Surface hardnessねじ部表面硬度
HRC58~62(Thread area)
Anti-rust treatment防錆処理
Anti-rust oil防錆油
see table below
M6(Oil hole/給油穴)
L2
PCD 45
φ34-
0.05
-0.
10
(φ
15)
50
34
30°
4-φ5.5φ9.5Depth/深5.5 Facing/ざぐり
30°
φ57
11
5.5
52
(28.5)
F
E-F下表参照
E
A281 A282
ボー
ルね
じBall Scresw
標準
在庫
品
SR/SSRシリ
ーズ
Standard products in stock SR/SSR series
ボー
ルね
じBall Scresw
標準
在庫
品
SR/SSRシリ
ーズ
Standard products in stock SR/SSR series
Unit(単位):mm
Ball Screw Modelボールねじ型番
Travelストローク
Grade精度
Shaft lengthねじ軸長さ
Lead accuracyリード精度 Total
Run-out全振れ
Axialplay
軸方向すきま
PreloadTorque予圧トルク
Nm
Basic Load Rating基本定格荷重 N
L1 L2
Travel deviation代表移動量誤差
ep
Variation変動V300
Dynamic動定格荷重
Ca
Static静定格荷重
Coa
SSR0801-400C7 335 Ct7 352 400 ±0.06 0.05 0.120 ~0.020ー 630 1250
SSR0801-400C10 335 Ct10 352 400 ±0.24 0.21 0.240 ~0.050
Note)Please designate end-journal profile with your sketch. 注)軸端の追加工は図面とともにご指示ください。
Unit(単位):mm
Ball Screw Specifications 諸元
Ball size ボール径 φ0.8
Number of thread 条数 1
Thread direction 巻方向 Right 右
Shaft root dia. ねじ軸谷径 φ7.3
Number of circuit 循環数 3.7×1
Shaft,Nut material軸、ナット材質 SUS440C
Surface hardnessねじ部表面硬度
HRC55~(Thread area)
Anti-rust treatment防錆処理
Anti-rust oil防錆油
Standard products in stock SSR series標準在庫品 SSRシリーズ
SSR0801 Shaft dia.(軸径)φ8 Lead(リード)1mm Ct7&Ct10Stainless ステンレス
下表参照see table below
G
G
L2
17
(13)4
C0.5
φ16
-0.0
5-0
.10
18
(φ
7.85)
PCD 23
φ29
30°
4-φ3.4
30°
408 L1(Quenched area / 焼入範囲)
40°
φ6
Unit(単位):mm
Ball Screw Modelボールねじ型番
Travelストローク
Grade精度
Shaft lengthねじ軸長さ
Lead accuracyリード精度 Total
Run-out全振れ
Axialplay
軸方向すきま
PreloadTorque予圧トルク
Nm
Basic Load Rating基本定格荷重 N
L1 L2
Travel deviation代表移動量誤差
ep
Variation変動V300
Dynamic動定格荷重
Ca
Static静定格荷重
Coa
SSR0601-300C7 240 Ct7 257 300 ±0.04 ー 0.120 ~0.020ー 560 900
SSR0601-300C10 240 Ct10 257 300 ±0.17 ー 0.240 ~0.050
Note)Please designate end-journal profile with your sketch. 注)軸端の追加工は図面とともにご指示ください。
Unit(単位):mm
Ball Screw Specifications 諸元
Ball size ボール径 φ0.8
Number of thread 条数 1
Thread direction 巻方向 Right 右
Shaft root dia. ねじ軸谷径 φ5.3
Number of circuit 循環数 3.7×1
Shaft,Nut material軸、ナット材質 SUS440C
Surface hardnessねじ部表面硬度
HRC55~(Thread area)
Anti-rust treatment防錆処理
Anti-rust oil防錆油
Standard products in stock SSR series標準在庫品 SSRシリーズ
SSR0601 Shaft dia.(軸径)φ6 Lead(リード)1mm Ct7&Ct10Stainless ステンレス
see table below
G
(13)4
C0.5
φ13
-0.0
5-0
.10
PCD 20
16
30°
17
φ26
(φ
5.85)
4-φ3.4
30°
L2
40°
358 L1(Quenched area / 焼入範囲)
φ4.
5
下表参照 G
A283 A284
ボー
ルね
じBall Scresw
標準
在庫
品
SR/SSRシリ
ーズ
Standard products in stock SR/SSR series
ボー
ルね
じBall Scresw
標準
在庫
品
SR/SSRシリ
ーズ
Standard products in stock SR/SSR series
Unit(単位):mm
Ball Screw Modelボールねじ型番
Travelストローク
Grade精度
Shaft lengthねじ軸長さ
Lead accuracyリード精度 Total
Run-out全振れ
Axialplay
軸方向すきま
PreloadTorque予圧トルク
Nm
Basic Load Rating基本定格荷重 N
L1 L2
Travel deviation代表移動量誤差
ep
Variation変動V300
Dynamic動定格荷重
Ca
Static静定格荷重
Coa
SSR1002-400C7 320 Ct7 347 400 ±0.06 0.05 0.080 ~0.020ー 2200 4000
SSR1002-400C10 320 Ct10 347 400 ±0.24 0.21 0.160 ~0.050
Note)Please designate end-journal profile with your sketch. 注)軸端の追加工は図面とともにご指示ください。
Unit(単位):mm
Ball Screw Specifications 諸元
Ball size ボール径 φ1.5875
Number of thread 条数 1
Thread direction 巻方向 Right 右
Shaft root dia. ねじ軸谷径 φ8.6
Number of circuit 循環数 3.7×1
Shaft,Nut material軸、ナット材質 SUS440C
Surface hardnessねじ部表面硬度
HRC55~(Thread area)
Anti-rust treatment防錆処理
Anti-rust oil防錆油
下表参照see table below
G
G
L2
C0.5
25
30°
PCD 32 φ40
24
(19)5
4-φ4.5
30°
φ23
-0.0
5-0
.10
(φ
9.7)
8
φ8
40°
45L1(Quenched area / 焼入範囲)
Standard products in stock SSR series標準在庫品 SSRシリーズ
SSR1002 Shaft dia.(軸径)φ10 Lead(リード)2mm Ct7&Ct10Stainless ステンレス
Unit(単位):mm
Ball Screw Modelボールねじ型番
Travelストローク
Grade精度
Shaft lengthねじ軸長さ
Lead accuracyリード精度 Total
Run-out全振れ
Axialplay
軸方向すきま
PreloadTorque予圧トルク
Nm
Basic Load Rating基本定格荷重 N
L1 L2
Travel deviation代表移動量誤差
ep
Variation変動V300
Dynamic動定格荷重
Ca
Static静定格荷重
Coa
SSR0802-400C7 325 Ct7 352 400 ±0.06 0.05 0.120 ~0.020ー 1950 3100
SSR0802-400C10 325 Ct10 352 400 ±0.24 0.21 0.240 ~0.050
Note)Please designate end-journal profile with your sketch. 注)軸端の追加工は図面とともにご指示ください。
Unit(単位):mm
Ball Screw Specifications 諸元
Ball size ボール径 φ1.5875
Number of thread 条数 1
Thread direction 巻方向 Right 右
Shaft root dia. ねじ軸谷径 φ6.6
Number of circuit 循環数 3.7×1
Shaft,Nut material軸、ナット材質 SUS440C
Surface hardnessねじ部表面硬度
HRC55~(Thread area)
Anti-rust treatment防錆処理
Anti-rust oil防錆油
下表参照see table below
G
G
L2
φ20
-0.0
5-0
.10
C0.5
24
(19)5
22
PCD 29
30°
4-φ4.5
30°
(φ
7.7)
φ37
408 L1(Quenched area / 焼入範囲)
40°
φ6
Standard products in stock SSR series標準在庫品 SSRシリーズ
SSR0802 Shaft dia.(軸径)φ8 Lead(リード)2mm Ct7&Ct10Stainless ステンレス
A285 A286
ボー
ルね
じBall Scresw
標準
在庫
品
SRT/SSRTシリ
ーズ
Standard products in stock SRT/SSRT series
ボー
ルね
じBall Scresw
標準
在庫
品
SRT/SSRTシリ
ーズ
Standard products in stock SRT/SSRT series
SRT/SSRT シリーズ つば付き転造ボールねじ標準在庫品SRT/SSRT seriesStandardized Rolled Ball Screws with Integrated end-journal
従来転造ボールねじは、加工の都合上、軸端径を細くする必要がありましたが、KSSの特殊技術採用により、削り出し品と同様に片側(固定側)をボールねじ部より大きく設定することが可能となりました。
●従来品との比較 Comparison with current model
●特長・ 軸端径を太く設計できるため、つば付き形状や汎用性のある軸受の使用が可能です。
・ 精密ボールねじ(削り出し品)の標準軸端形状と互換性があります。
・ カラー挿入や焼きばめに比べて、安定性が向上します。・ 軸端未加工での在庫保有により、設計の自由度が広がります。
・ 防錆のため、ステンレス製の対応も可能です。
●Features・ Design flexibility and wide use of Bearings on
end-journal.・ Compatible end-journal to Precision Ball Screws.・ No need to insert or press fit collar as Bearing
shoulder.・Quick delivery due to unfinished end-journal stock.・ Stainless Rolled Ball Screws are also available.
For production reason, Rolled Ball Screws are normally necessary to have smaller end-journal, but as KSS has adopted special technology, it enables fixed end-journal bigger than Shaft diameter alike Ground Ball Screws. This technology enables stable and more flexible on end-journal design.
軸端径を太く設定可能研削ボールねじとの互換性ありDesign flexibility & compatible designto Precision Ball Screws
転造加工による安価な製造方法Cost saving by Rolled process
***軸径φ10mm品での比較/ Shaft nominal diameter : φ10mm
従来品の軸端形状/ Current model design 新製品の軸端形状/ New model design
カラー装着や焼きばめの必要なしNot necessary to put or press fit a collar
つば付き形状による軸受端面の確保Flanged end-journal for Bearing face
二面幅を設けることが可能Possible to have across flats
●ねじ軸呼び外径とリードの組み合わせ Combination of Shaft nominal dia. & Lead
注1)黄色で示した型番はステンレス製の対応が可能です。注2)表中の数字:掲載ページを表す
Note 1)Yellow cells are available for Stainless Shaft and Nut.Note 2)The numbers in a table :showing a page in this catalogue
Leadリード
Shaft dia.呼び外径
1 2 2.5 4 5 6 8 10 12 15 20
4 A289A290 A291
5 A292
6A293A294A315
A295 A296 A297
8A298A299A316
A300A301A317
A302 A303 A304 A305
10A306A307A318
A308 A309 A310 A311
12 A312A313 A314
Unit(単位):mm
●材質と表面硬度SRT/SSRTシリーズ (つば付き転造/ステンレスつば付き転造ボールねじ標準在庫品)の材質と表面硬度は、以下のとおりです。
●精度等級と軸方向すきまSRT/SSRTシリーズ(つば付き転造/ステンレスつば付き転造ボールねじ標準在庫品)の精度等級は、Ct7およびCt10(JIS B 1192-3)となります。また軸方向すきまは、精度等級に応じて0.020mm以下(Ct7)および0.050mm以下(Ct10)を在庫しています。
●Material & Surface hardnessThe material and hardness of SRT/SSRT series (Standardized Rolled & Stainless Rolled Ball Screws with Integrated end-journal) are as follows.
●Accuracy Grade & Axial playThe grade of SRT/SSRT series (Standardized Rolled & Stainless Rolled Ball Screws with Integrated end-journal) are Ct7 and Ct10(JIS B 1192-3).According to accuracy grade, Axial play 0.020mm or less (Ct7) and 0.050mm or less(Ct10) are in stock.
Products製品種別
Material of thread areaボールねじ部材質
Heat treatment熱処理
Surface hardnessボールねじ部の表面硬度
Rolled Ball Screws(SRT series )
一般転造(SRTシリーズ)
Shaft / ねじ軸 : SCM415S55C
Carburizing and Quenching浸炭焼き入れ
Induction hardening高周波焼き入れ
HRC58 or moreHRC58以上
Nut / ナット : SCM415
Stainless Rolled Ball Screws (SSRT series )
ステンレス転造(SSRTシリーズ)
Shaft / ねじ軸 : SUS440CInduction hardening高周波焼き入れ HRC55 or more
HRC55以上Nut / ナット : SUS440C
Vacuum hardening真空焼き入れ
φ8
φ6φ10
Across flats/二面幅
Bearing face/つば部
φ10 φ8
φ6φ
11.5
A287 A288
ボー
ルね
じBall Scresw
標準
在庫
品
SRT/SSRTシリ
ーズ
Standard products in stock SRT/SSRT series
ボー
ルね
じBall Scresw
標準
在庫
品
SRT/SSRTシリ
ーズ
Standard products in stock SRT/SSRT series
●注記1)軸端の詳細寸法は、各ページを参照してください。2)KSSでは、ナットの追加工は行いません。3)仕様は予告なく変更する場合があります。4)標準の軸端形状(A,B,C)以外の形状をご要望の場合は、
KSSへ問い合わせください。
●Note1)The detail of end-journal dimension for each size
is shown from next page.2)KSS does not make additional Nut machining.3)The specification is subject to change without
notice.4)If the other configuration except (A,B,C)is
requested, please contact KSS.
126 C7 B 1 XSRT 04 01 086 Rー
●呼び番号の構成 Model number notation
①シリーズ記号SRT : つば付き転造ボールねじSSRT : ステンレスつば付き転造ボールねじ②ねじ軸呼び外径(mm)③リード(mm)④ナット形式無記号 : 一般K : コンパクトタイプ⑤ねじ部長さ(mm)(追加工後は1mm単位で指定)⑥巻方向(R=右ねじ)⑦ねじ軸全長(mm)(1mm単位で指定)⑧精度等級(C7 or C10)⑨端末加工タイプ図 A-24参照 : A-type,B-type,C-type,
D-type(その他)⑩塗布剤
0 : KSS推奨グリーズ(MSG No.2)1 : 防錆油(Non Ruster PZ2)2 : マルテンプPS23 : その他⑪ナットフランジ向き(図 A-25参照)
①Rolled Ball Screws Series No.SRT : Rolled Ball Screws with Integrated end-journalSSRT : Stainless Rolled Ball Screws with Integrated end-journal②Screw Shaft nominal diameter(mm)③Lead(mm)④Ball Nut type
None : StandardK : Compact type⑤Screw thread length(mm)(Specify in 1mm unit after end-journal machining)⑥Thread direction(R=Right-hand)⑦Screw Shaft total length(mm)(Specify in 1mm unit)⑧Accuracy grade(C7 or C10)⑨Shaft end-journal profile
Refer to Fig. A-24 below : A-type,B-type,C-type,D-type(other)
⑩Anti-rust oil or Lubricant0 : KSS grease(MSG No.2)1 : Anti-rust oil(Non Ruster PZ2)2 : Multemp PS2 grease3 : Other⑪Nut Flange direction(Refer to Fig. A-25 below)
① ② ③ ⑤ ⑥ ⑦ ⑧ ⑨ ⑩ ⑪
図 A-25 : ナットフランジ向きFig. A-25 : Nut Flange direction
X : Fixed side / 固定側
Y : Supported side / 支持側
図 A-24 : 端末加工タイプ Fig. A-24 : Shaft end-journal profile
A-type : Free / 加工なし
B-type : Journal with snap ring groove / リング溝タイプ
C-type : Journal only / ストレートタイプ
●精密転造ボールねじ転造ボールねじで高精度(JIS C5)を実現した転造ボールねじ(PSR/PSRTシリーズ)も製作可能です。ページA319を参照ください。
●Precision Rolled Ball ScrewsHigh accuracy(JIS C5) can be produced by Rolled process, what we call Precision Rolled Ball Screws(PSR/PSRT series).Please see page A319.
●潤滑SRT/SSRTシリーズ (つば付き転造/ステンレスつば付き転造ボールねじ標準在庫品)は、端末未加工状態では、防錆処置のため防錆油を塗布しています。なお防錆油は潤滑機能がありませんので、ご使用に際しては別途潤滑剤を供給してください。特にご指定のない場合、KSSオリジナルグリース(MSG No.2)を推奨いたします。
●LubricationSRT/SSRT series (Standardized Rolled & Stainless Rolled Ball Screws with Integrated end-journal) will be supplied with anti-rust oil.This oil is not lubricant, when Ball Screw operates, lubricant should be applied.If there is no specific instruction, KSS would recommend our original Grease (MSG No.2) as standard lubricant. Please feel free to contact us.
K④
D-type : Other than the above / 上記以外の形状
A289 A290
ボー
ルね
じBall Scresw
標準
在庫
品
SRT/SSRTシリ
ーズ
Standard products in stock SRT/SSRT series
ボー
ルね
じBall Scresw
標準
在庫
品
SRT/SSRTシリ
ーズ
Standard products in stock SRT/SSRT series
Unit(単位):mm
Ball Screw Modelボールねじ型番
Travelストローク
Grade精度
Shaft lengthねじ軸長さ
Lead accuracyリード精度
Total Run-out全振れ
Axialplay
軸方向すきま
PreloadTorque予圧トルク
Nm
Basic Load Rating基本定格荷重 N
L1 L2 L3
Travel deviation代表移動量誤差
ep
Variation変動V300
Dynamic動定格荷重
Ca
Static静定格荷重
Coa
SRT0401-96R155C7 75 Ct7 96 100 155 ±0.02 ー 0.080~0.020
ー 560 790SRT0401-216R275C7 195 Ct7 216 220 275 ±0.03 ー 0.120
SRT0401-96R155C10 75 Ct10 96 100 155 ±0.06 ー 0.160~0.050
SRT0401-216R275C10 195 Ct10 216 220 275 ±0.15 ー 0.240
Note )Please refer to page A287 for order code of end-journal machining. 注)追加工の呼び番号指定方法はぺージA287をご参照ください。
Unit(単位):mm
Ball Screw Specifications 諸元
Ball size ボール径 φ0.8
Number of thread 条数 1
Thread direction 巻方向 Right 右
Shaft root dia. ねじ軸谷径 φ3.3
Number of circuit 循環数 3.7×1
Material材質
Shaft 軸 SCM415H+SUS303
Nut ナット SCM415H
Surface hardnessねじ部表面硬度
HRC58~(Thread area)
Anti-rust treatment防錆処理
Anti-rust oil防錆油
G
G
A11-SRT0401
下表参照see table below
55
φ8.
2
C0.5
(13) 4
C0.5
17φ
11-
0.05
-0.
10
4-φ3.4
30°
15
30°
(φ
3.85)
PCD 17
φ23
4
L3
L2
L1
Standard products in stock SRT series標準在庫品 SRTシリーズ
SRT0401
Support-unit Recommendation推奨サポートユニット
Supported-side 支持側 : MSU-4CS/4GFixed-side 固定側 : MSU-4C/4G
L4:Thread length after end-journal machining. 追加工後のねじ部長さL5:Total length after end-journal machining. 追加工後全長
R0.15max
7
L4=L5ー33
L4=L5ー40
R0.15max
L5
L5
L4=L5ー40
L5
L5
L4
2.5
5
23
φ3h
6 0 -0.
006
φ4-
0.00
1-
0.00
6
φ6h
8 0 -0.
018
6.5
18
5 0-0.2
30°×0.3
M4×0.5
6
7
φ3-
0.00
2-
0.01
0
φ2.
7±
0.03
4.35 ±0.05
0.5+0.1 0
φ3-
0.00
2-
0.01
0
R0.2max
4
A11-SRT04、05 journal
A-type B-type C-type
End-journal profile 端末加工形状 Supported-side 支持側 Fixed-side 固定側
Shaft dia.(軸径)φ4 Lead(リード)1mm Ct7&Ct10
Unit(単位):mm
Ball Screw Modelボールねじ型番
Travelストローク
Grade精度
Shaft lengthねじ軸長さ
Lead accuracyリード精度
Total Run-out全振れ
Axialplay
軸方向すきま
PreloadTorque予圧トルク
Nm
Basic Load Rating基本定格荷重 N
L1 L2 L3
Travel deviation代表移動量誤差
ep
Variation変動V300
Dynamic動定格荷重
Ca
Static静定格荷重
Coa
SRT0401K-76R115C7 60 Ct7 76 80 115 ±0.02 ー 0.080 ~0.020ー 300 430
SRT0401K-76R115C10 60 Ct10 76 80 115 ±0.05 ー 0.160 ~0.050
Note )Please refer to page A287 for order code of end-journal machining. 注)追加工の呼び番号指定方法はぺージA287をご参照ください。
Unit(単位):mm
Ball Screw Specifications 諸元
Ball size ボール径 φ0.6
Number of thread 条数 1
Thread direction 巻方向 Right 右
Shaft root dia. ねじ軸谷径 φ3.4
Number of circuit 循環数 1×3
Material材質
Shaft 軸 S55C+SUS303
Nut ナット SCM415H
Surface hardnessねじ部表面硬度
HRC58~(Thread area)
Anti-rust treatment防錆処理
Anti-rust oil防錆油
G
G下表参照see table below
35
φ8.
2
C0.5
(10)3
C0.5
13
φ9-
0.05
-0.
10
4-φ2.9
30°
13
30°
(φ
3.95)
PCD 14
φ19
4
L3
L2
L1
Standard products in stock SRT series標準在庫品 SRTシリーズ
SRT0401K
Support-unit Recommendation推奨サポートユニット
Supported-side 支持側 : MSU-4CS/4GSFixed-side 固定側 : MSU-4C/4G
L4:Thread length after end-journal machining. 追加工後のねじ部長さL5:Total length after end-journal machining. 追加工後全長
R0.15max
7
L4=L5ー33
L4=L5ー40
R0.15max
L5
L5
L4=L5ー40
L5
L5
L4
2.5
5
23
φ3h
6 0 -0.
006
φ4-
0.00
1-
0.00
6
φ6h
8 0 -0.
018
6.5
18
5 0-0.2
30°×0.3
M4×0.5
6
7
φ3-
0.00
2-
0.01
0
φ2.
7±
0.03
4.35 ±0.05
0.5+0.1 0
φ3-
0.00
2-
0.01
0
R0.2max
4
A11-SRT04、05 journal
A-type B-type C-type
End-journal profile 端末加工形状 Supported-side 支持側 Fixed-side 固定側
Shaft dia.(軸径)φ4 Lead(リード)1mm Ct7&Ct10
D-type : Other than the above. 上記以外の形状 D-type : Other than the above. 上記以外の形状
Compact Nut / コンパクトナット
A291 A292
ボー
ルね
じBall Scresw
標準
在庫
品
SRT/SSRTシリ
ーズ
Standard products in stock SRT/SSRT series
ボー
ルね
じBall Scresw
標準
在庫
品
SRT/SSRTシリ
ーズ
Standard products in stock SRT/SSRT series
R0.15max
7
L4=L5ー33
L4=L5ー40
R0.15max
L5
L5
L4=L5ー40
L5
L5
L4
2.5
5
23
φ3h
6 0 -0.
006
φ4-
0.00
1-
0.00
6
φ6h
8 0 -0.
018
6.5
18
5 0-0.2
30°×0.3
M4×0.5
6
7
φ3-
0.00
2-
0.01
0
φ2.
7±
0.03
4.35 ±0.05
0.5+0.1 0
φ3-
0.00
2-
0.01
0
R0.2max
4
A11-SRT04、05 journal
A-type B-type C-type
Fixed-side 固定側
Unit(単位):mm
Ball Screw Modelボールねじ型番
Travelストローク
Grade精度
Shaft lengthねじ軸長さ
Lead accuracyリード精度
Total Run-out全振れ
Axialplay
軸方向すきま
PreloadTorque予圧トルク
Nm
Basic Load Rating基本定格荷重 N
L1 L2 L3
Travel deviation代表移動量誤差
ep
Variation変動V300
Dynamic動定格荷重
Ca
Static静定格荷重
Coa
SRT0402-96R155C7 75 Ct7 96 100 155 ±0.02 ー 0.080~0.020
ー 420 570SRT0402-216R275C7 195 Ct7 216 220 275 ±0.03 ー 0.120
SRT0402-96R155C10 75 Ct10 96 100 155 ±0.06 ー 0.160~0.050
SRT0402-216R275C10 195 Ct10 216 220 275 ±0.15 ー 0.240
Note )Please refer to page A287 for order code of end-journal machining. 注)追加工の呼び番号指定方法はぺージA287をご参照ください。
Unit(単位):mm
Ball Screw Specifications 諸元
Ball size ボール径 φ0.8
Number of thread 条数 1
Thread direction 巻方向 Right 右
Shaft root dia. ねじ軸谷径 φ3.3
Number of circuit 循環数 2.7×1
Material材質
Shaft 軸 SCM415H+SUS303
Nut ナット SCM415H
Surface hardnessねじ部表面硬度
HRC58~(Thread area)
Anti-rust treatment防錆処理
Anti-rust oil防錆油
G
G
A11-SRT0402
下表参照see table below
55
φ8.
2
C0.5
4-φ3.4
30°
15
30°
(φ
3.85)
PCD 17
4
φ11-
0.05
-0.
1019
(15)
φ23
C0.5
4
L3
L2
L1
Standard products in stock SRT series標準在庫品 SRTシリーズ
SRT0402
Support-unit Recommendation推奨サポートユニット
Supported-side 支持側 : MSU-4CS/4GSFixed-side 固定側 : MSU-4C/4G
L4:Thread length after end-journal machining. 追加工後のねじ部長さL5:Total length after end-journal machining. 追加工後全長
End-journal profile 端末加工形状 Supported-side 支持側
Shaft dia.(軸径)φ4 Lead(リード)2mm Ct7&Ct10
Unit(単位):mm
Ball Screw Modelボールねじ型番
Travelストローク
Grade精度
Shaft lengthねじ軸長さ
Lead accuracyリード精度
Total Run-out全振れ
Axialplay
軸方向すきま
PreloadTorque予圧トルク
Nm
Basic Load Rating基本定格荷重 N
L1 L2 L3
Travel deviation代表移動量誤差
ep
Variation変動V300
Dynamic動定格荷重
Ca
Static静定格荷重
Coa
SRT0504-96R155C7 70 Ct7 96 100 155 ±0.02 ー 0.080~0.020
ー 470 720SRT0504-216R275C7 190 Ct7 216 220 275 ±0.03 ー 0.120
SRT0504-96R155C10 70 Ct10 96 100 155 ±0.06 ー 0.160~0.050
SRT0504-216R275C10 190 Ct10 216 220 275 ±0.15 ー 0.240
Note )Please refer to page A287 for order code of end-journal machining. 注)追加工の呼び番号指定方法はぺージA287をご参照ください。
Unit(単位):mm
Ball Screw Specifications 諸元
Ball size ボール径 φ0.8
Number of thread 条数 1
Thread direction 巻方向 Right 右
Shaft root dia. ねじ軸谷径 φ4.3
Number of circuit 循環数 2.7×1
Material材質
Shaft 軸 SCM415H+SUS303
Nut ナット SCM415H
Surface hardnessねじ部表面硬度
HRC58~(Thread area)
Anti-rust treatment防錆処理
Anti-rust oil防錆油
G
A11-SRT0504
下表参照see table below
G
55
4
φ8.
2
C0.5
4
φ12-
0.05
-0.
10
PCD 18
22
(18)
4-φ3.4
30°
16
φ24
(φ
4.85)
30°
C0.5
L3
L2
L1
Standard products in stock SRT series標準在庫品 SRTシリーズ
SRT0504
Support-unit Recommendation推奨サポートユニット
Supported-side 支持側 : MSU-4CS/4GSFixed-side 固定側 : MSU-4C/4G
L4:Thread length after end-journal machining. 追加工後のねじ部長さL5:Total length after end-journal machining. 追加工後全長
End-journal profile 端末加工形状 Supported-side 支持側
Shaft dia.(軸径)φ5 Lead(リード)4mm Ct7&Ct10
Fixed-side 固定側
R0.15max
7
L4=L5ー33
L4=L5ー40
R0.15max
L5
L5
L4=L5ー40
L5
L5
L4
2.5
5
23
φ3h
6 0 -0.
006
φ4-
0.00
1-
0.00
6
φ6h
8 0 -0.
018
6.5
18
5 0-0.2
30°×0.3
M4×0.5
6
7
φ3-
0.00
2-
0.01
0
φ2.
7±
0.03
4.35 ±0.05
0.5+0.1 0
φ3-
0.00
2-
0.01
0
R0.2max
4
A11-SRT04、05 journal
A-type B-type C-type
D-type : Other than the above. 上記以外の形状 D-type : Other than the above. 上記以外の形状
A293 A294
ボー
ルね
じBall Scresw
標準
在庫
品
SRT/SSRTシリ
ーズ
Standard products in stock SRT/SSRT series
ボー
ルね
じBall Scresw
標準
在庫
品
SRT/SSRTシリ
ーズ
Standard products in stock SRT/SSRT series
Unit(単位):mm
Ball Screw Modelボールねじ型番
Travelストローク
Grade精度
Shaft lengthねじ軸長さ
Lead accuracyリード精度
Total Run-out全振れ
Axialplay
軸方向すきま
PreloadTorque予圧トルク
Nm
Basic Load Rating基本定格荷重 N
L1 L2 L3
Travel deviation代表移動量誤差
ep
Variation変動V300
Dynamic動定格荷重
Ca
Static静定格荷重
Coa
SRT0601K-91R135C7 70 Ct7 91 95 135 ±0.02 ー 0.080 ~0.020ー 560 950
SRT0601K-91R135C10 70 Ct10 91 95 135 ±0.06 ー 0.160 ~0.050
Note )Please refer to page A287 for order code of end-journal machining. 注)追加工の呼び番号指定方法はぺージA287をご参照ください。
Unit(単位):mm
Ball Screw Specifications 諸元
Ball size ボール径 φ0.8
Number of thread 条数 1
Thread direction 巻方向 Right 右
Shaft root dia. ねじ軸谷径 φ5.3
Number of circuit 循環数 1×3
Material材質
Shaft 軸 S55C+SUS303
Nut ナット SCM415H
Surface hardnessねじ部表面硬度
HRC58~(Thread area)
Anti-rust treatment防錆処理
Anti-rust oil防錆油
下表参照see table below
G
G
40
φ9.
7
C0.5
(11) 3.5
C0.5
φ11-
0.05
-0.
10
PCD 17
15
30°
14.5
φ23
(φ
5.9)
4-φ3.4
30°
4
L3
L2
L1
Standard products in stock SRT series標準在庫品 SRTシリーズ
SRT0601K
Support-unit Recommendation推奨サポートユニット
Supported-side 支持側 : MSU-5CS/5GSFixed-side 固定側 : MSU-5C/5G
L4:Thread length after end-journal machining. 追加工後のねじ部長さL5:Total length after end-journal machining. 追加工後全長
End-journal profile 端末加工形状 Supported-side 支持側
Shaft dia.(軸径)φ6 Lead(リード)1mm Ct7&Ct10
Fixed-side 固定側A11-SRT06 journal
L5
R0.2max
8
R0.2max
φ8h
8 0 -0.
022
φ5-
0.00
1-
0.00
6
φ4h
6 0 -0.
008
19 6
6.5
M5×0.5
30°×0.5
R0.2max
3
7 0-0.2
257
8
φ4-
0.00
2-
0.01
0
φ3.
7±
0.03
φ4-
0.00
2-
0.01
0
5.35 ±0.05
0.5+0.1 0
4
L4=L5ー36
L5
L4=L5ー44
L5
L5
L4
L4=L5ー44
A-type B-type C-type
D-type : Other than the above. 上記以外の形状
Compact Nut / コンパクトナット
Unit(単位):mm
Ball Screw Modelボールねじ型番
Travelストローク
Grade精度
Shaft lengthねじ軸長さ
Lead accuracyリード精度
Total Run-out全振れ
Axialplay
軸方向すきま
PreloadTorque予圧トルク
Nm
Basic Load Rating基本定格荷重 N
L1 L2 L3
Travel deviation代表移動量誤差
ep
Variation変動V300
Dynamic動定格荷重
Ca
Static静定格荷重
Coa
SRT0601-146R220C7 125 Ct7 146 150 220 ±0.02 ー 0.080~0.020
ー 680 1200SRT0601-261R335C7 240 Ct7 261 265 335 ±0.04 ー 0.120
SRT0601-146R220C10 125 Ct10 146 150 220 ±0.10 ー 0.160~0.050
SRT0601-261R335C10 240 Ct10 261 265 335 ±0.18 ー 0.240
Note )Please refer to page A287 for order code of end-journal machining. 注)追加工の呼び番号指定方法はぺージA287をご参照ください。
Unit(単位):mm
Ball Screw Specifications 諸元
Ball size ボール径 φ0.8
Number of thread 条数 1
Thread direction 巻方向 Right 右
Shaft root dia. ねじ軸谷径 φ5.3
Number of circuit 循環数 3.7×1
Material材質
Shaft 軸 SCM415H+SUS303
Nut ナット SCM415H
Surface hardnessねじ部表面硬度
HRC58~(Thread area)
Anti-rust treatment防錆処理
Anti-rust oil防錆油
A11-SRT0601
下表参照see table below
G
G
70
φ9.
7
C0.5
(13) 4
C0.5
φ13-
0.05
-0.
10
PCD 20
16
30°
17
φ26
(φ
5.85)
4-φ3.4
30°
4
L3
L2
L1
Standard products in stock SRT series標準在庫品 SRTシリーズ
SRT0601
Support-unit Recommendation推奨サポートユニット
Supported-side 支持側 : MSU-5CS/5GSFixed-side 固定側 : MSU-5C/5G
L4:Thread length after end-journal machining. 追加工後のねじ部長さL5:Total length after end-journal machining. 追加工後全長
End-journal profile 端末加工形状 Supported-side 支持側
Shaft dia.(軸径)φ6 Lead(リード)1mm Ct7&Ct10
Fixed-side 固定側A11-SRT06 journal
L5
R0.2max
8
R0.2max
φ8h
8 0 -0.
022
φ5-
0.00
1-
0.00
6
φ4h
6 0 -0.
008
19 6
6.5
M5×0.5
30°×0.5
R0.2max
3
7 0-0.2
257
8
φ4-
0.00
2-
0.01
0
φ3.
7±
0.03
φ4-
0.00
2-
0.01
0
5.35 ±0.05
0.5+0.1 0
4
L4=L5ー36
L5
L4=L5ー44
L5
L5
L4
L4=L5ー44
A-type B-type C-type
D-type : Other than the above. 上記以外の形状
*Please refer to page A315 for stainless steel type.※ステンレスタイプはぺージA315をご参照ください。
A295 A296
ボー
ルね
じBall Scresw
標準
在庫
品
SRT/SSRTシリ
ーズ
Standard products in stock SRT/SSRT series
ボー
ルね
じBall Scresw
標準
在庫
品
SRT/SSRTシリ
ーズ
Standard products in stock SRT/SSRT series
Unit(単位):mm
Ball Screw Modelボールねじ型番
Travelストローク
Grade精度
Shaft lengthねじ軸長さ
Lead accuracyリード精度
Total Run-out全振れ
Axialplay
軸方向すきま
PreloadTorque予圧トルク
Nm
Basic Load Rating基本定格荷重 N
L1 L2 L3
Travel deviation代表移動量誤差
ep
Variation変動V300
Dynamic動定格荷重
Ca
Static静定格荷重
Coa
SRT0602-146R220C7 125 Ct7 146 150 220 ±0.02 ー 0.080~0.020
ー 750 1200SRT0602-261R335C7 240 Ct7 261 265 335 ±0.04 ー 0.120
SRT0602-146R220C10 125 Ct10 146 150 220 ±0.10 ー 0.160~0.050
SRT0602-261R335C10 240 Ct10 261 265 335 ±0.18 ー 0.240
Note )Please refer to page A287 for order code of end-journal machining. 注)追加工の呼び番号指定方法はぺージA287をご参照ください。
Unit(単位):mm
Ball Screw Specifications 諸元
Ball size ボール径 φ1.0
Number of thread 条数 1
Thread direction 巻方向 Right 右
Shaft root dia. ねじ軸谷径 φ5.1
Number of circuit 循環数 2.7×1
Material材質
Shaft 軸 SCM415H+SUS303
Nut ナット SCM415H
Surface hardnessねじ部表面硬度
HRC58~(Thread area)
Anti-rust treatment防錆処理
Anti-rust oil防錆油
G
A11-SRT0602
下表参照see table below
G
70
φ15-
0.05
-0.
10
17
(13) 4
C0.5
PCD 22
30°
φ28
19
30°
4-φ3.4
φ9.
7
C0.5
4
(φ
5.8)
L3
L2
L1
Standard products in stock SRT series標準在庫品 SRTシリーズ
SRT0602
Support-unit Recommendation推奨サポートユニット
Supported-side 支持側 : MSU-5CS/5GSFixed-side 固定側 : MSU-5C/5G
L4:Thread length after end-journal machining. 追加工後のねじ部長さL5:Total length after end-journal machining. 追加工後全長
End-journal profile 端末加工形状 Supported-side 支持側
Shaft dia.(軸径)φ6 Lead(リード)2mm Ct7&Ct10
Unit(単位):mm
Ball Screw Modelボールねじ型番
Travelストローク
Grade精度
Shaft lengthねじ軸長さ
Lead accuracyリード精度
Total Run-out全振れ
Axialplay
軸方向すきま
PreloadTorque予圧トルク
Nm
Basic Load Rating基本定格荷重 N
L1 L2 L3
Travel deviation代表移動量誤差
ep
Variation変動V300
Dynamic動定格荷重
Ca
Static静定格荷重
Coa
SRT0606-146R220C7 125 Ct7 146 150 220 ±0.02 ー 0.080~0.020
ー 870 1450SRT0606-261R335C7 240 Ct7 261 265 335 ±0.04 ー 0.120
SRT0606-146R220C10 125 Ct10 146 150 220 ±0.10 ー 0.160~0.050
SRT0606-261R335C10 240 Ct10 261 265 335 ±0.18 ー 0.240
Note )Please refer to page A287 for order code of end-journal machining. 注)追加工の呼び番号指定方法はぺージA287をご参照ください。
Unit(単位):mm
Ball Screw Specifications 諸元
Ball size ボール径 φ1.0
Number of thread 条数 2
Thread direction 巻方向 Right 右
Shaft root dia. ねじ軸谷径 φ5.2
Number of circuit 循環数 1.6×2
Material材質
Shaft 軸 SCM415H+SUS303
Nut ナット SCM415H
Surface hardnessねじ部表面硬度
HRC58~(Thread area)
Anti-rust treatment防錆処理
Anti-rust oil防錆油
G
A11-SRT0606
下表参照see table below
G
70
φ9.
7
C0.5
30° 30°
4-φ3.4
PCD 21
16
(φ
5.9) φ14-
0.05
-0.
10
φ27
17
4(8)
4
L3
L2
L1
Standard products in stock SRT series標準在庫品 SRTシリーズ
SRT0606
Support-unit Recommendation推奨サポートユニット
Supported-side 支持側: MSU-5CS/5GSFixed-side 固定側: MSU-5C/5G
L4:Thread length after end-journal machining. 追加工後のねじ部長さL5:Total length after end-journal machining. 追加工後全長
End-journal profile 端末加工形状 Supported-side 支持側
Shaft dia.(軸径)φ6 Lead(リード)6mm Ct7&Ct10
Fixed-side 固定側 Fixed-side 固定側A11-SRT06 journal
L5
R0.2max
8
R0.2max
φ8h
8 0 -0.
022
φ5-
0.00
1-
0.00
6
φ4h
6 0 -0.
008
19 6
6.5
M5×0.5
30°×0.5
R0.2max
3
7 0-0.2
257
8
φ4-
0.00
2-
0.01
0
φ3.
7±
0.03
φ4-
0.00
2-
0.01
0
5.35 ±0.05
0.5+0.1 0
4
L4=L5ー36
L5
L4=L5ー44
L5
L5
L4
L4=L5ー44
A-type B-type C-type
A11-SRT06 journal
L5
R0.2max
8
R0.2max
φ8h
8 0 -0.
022
φ5-
0.00
1-
0.00
6
φ4h
6 0 -0.
008
19 6
6.5
M5×0.5
30°×0.5
R0.2max
3
7 0-0.2
257
8
φ4-
0.00
2-
0.01
0
φ3.
7±
0.03
φ4-
0.00
2-
0.01
0
5.35 ±0.05
0.5+0.1 0
4
L4=L5ー36
L5
L4=L5ー44
L5
L5
L4
L4=L5ー44
A-type B-type C-type
D-type : Other than the above. 上記以外の形状 D-type : Other than the above. 上記以外の形状
A297 A298
ボー
ルね
じBall Scresw
標準
在庫
品
SRT/SSRTシリ
ーズ
Standard products in stock SRT/SSRT series
ボー
ルね
じBall Scresw
標準
在庫
品
SRT/SSRTシリ
ーズ
Standard products in stock SRT/SSRT series
Unit(単位):mm
Ball Screw Modelボールねじ型番
Travelストローク
Grade精度
Shaft lengthねじ軸長さ
Lead accuracyリード精度
Total Run-out全振れ
Axialplay
軸方向すきま
PreloadTorque予圧トルク
Nm
Basic Load Rating基本定格荷重 N
L1 L2 L3
Travel deviation代表移動量誤差
ep
Variation変動V300
Dynamic動定格荷重
Ca
Static静定格荷重
Coa
SRT0610-146R220C7 120 Ct7 146 150 220 ±0.02 ー 0.080~0.020
ー 950 1600SRT0610-261R335C7 235 Ct7 261 265 335 ±0.04 ー 0.120
SRT0610-146R220C10 120 Ct10 146 150 220 ±0.10 ー 0.160~0.050
SRT0610-261R335C10 235 Ct10 261 265 335 ±0.18 ー 0.240
Note )Please refer to page A287 for order code of end-journal machining. 注)追加工の呼び番号指定方法はぺージA287をご参照ください。
Unit(単位):mm
Ball Screw Specifications 諸元
Ball size ボール径 φ1.2
Number of thread 条数 2
Thread direction 巻方向 Right 右
Shaft root dia. ねじ軸谷径 φ5.0
Number of circuit 循環数 1.2×2
Material材質
Shaft 軸 SCM415H+SUS303
Nut ナット SCM415H
Surface hardnessねじ部表面硬度
HRC58~(Thread area)
Anti-rust treatment防錆処理
Anti-rust oil防錆油
A11-SRT0610
下表参照see table below
G
G
70
φ9.
7
C0.5
4 30° 30°
4-φ3.4
PCD 21
16
φ14-
0.05
-0.
10
φ27
23
(11.5)
(φ
5.9)
4
L3
L2
L1
Standard products in stock SRT series標準在庫品 SRTシリーズ
SRT0610
Support-unit Recommendation推奨サポートユニット
Supported-side 支持側 : MSU-5CS/5GSFixed-side 固定側 : MSU-5C/5G
L4:Thread length after end-journal machining. 追加工後のねじ部長さL5:Total length after end-journal machining. 追加工後全長
End-journal profile 端末加工形状 Supported-side 支持側
Shaft dia.(軸径)φ6 Lead(リード)10mm Ct7&Ct10
Fixed-side 固定側A11-SRT06 journal
L5
R0.2max
8
R0.2max
φ8h
8 0 -0.
022
φ5-
0.00
1-
0.00
6
φ4h
6 0 -0.
008
19 6
6.5
M5×0.5
30°×0.5
R0.2max
3
7 0-0.2
257
8
φ4-
0.00
2-
0.01
0
φ3.
7±
0.03
φ4-
0.00
2-
0.01
0
5.35 ±0.05
0.5+0.1 0
4
L4=L5ー36
L5
L4=L5ー44
L5
L5
L4
L4=L5ー44
A-type B-type C-type
D-type : Other than the above. 上記以外の形状 Unit(単位):mm
Ball Screw Modelボールねじ型番
Travelストローク
Grade精度
Shaft lengthねじ軸長さ
Lead accuracyリード精度
Total Run-out全振れ
Axialplay
軸方向すきま
PreloadTorque予圧トルク
Nm
Basic Load Rating基本定格荷重 N
L1 L2 L3
Travel deviation代表移動量誤差
ep
Variation変動V300
Dynamic動定格荷重
Ca
Static静定格荷重
Coa
SRT0801-196R270C7 175 Ct7 196 200 270 ±0.03 ー 0.080~0.020
ー 780 1650SRT0801-356R430C7 335 Ct7 356 360 430 ±0.06 0.05 0.120
SRT0801-196R270C10 175 Ct10 196 200 270 ±0.13 ー 0.160~0.050
SRT0801-356R430C10 335 Ct10 356 360 430 ±0.24 0.21 0.240
Note )Please refer to page A287 for order code of end-journal machining. 注)追加工の呼び番号指定方法はぺージA287をご参照ください。
Unit(単位):mm
Ball Screw Specifications 諸元
Ball size ボール径 φ0.8
Number of thread 条数 1
Thread direction 巻方向 Right 右
Shaft root dia. ねじ軸谷径 φ7.3
Number of circuit 循環数 3.7×1
Material材質
Shaft 軸 SCM415H+SUS303
Nut ナット SCM415H
Surface hardnessねじ部表面硬度
HRC58~(Thread area)
Anti-rust treatment防錆処理
Anti-rust oil防錆油
A11-SRT0801
下表参照see table below
G
G
4
C0.5
70
φ14
.2
17
(13) 4
C0.5
φ16-
0.05
-0.
10 30°
18
PCD 23
φ29
4-φ3.4
30°
(φ
7.85)
4
L3
L2
L1
Standard products in stock SRT series標準在庫品 SRTシリーズ
SRT0801
Support-unit Recommendation推奨サポートユニット
Supported-side 支持側 : MSU-6CS/6GSFixed-side 固定側 : MSU-6C/6G
L4:Thread length after end-journal machining. 追加工後のねじ部長さL5:Total length after end-journal machining. 追加工後全長
End-journal profile 端末加工形状 Supported-side 支持側
Shaft dia.(軸径)φ8 Lead(リード)1mm Ct7&Ct10
Fixed-side 固定側A11-SRT08 journal
6.8 +0.1 0
0.8+0.1 0
φ5.
7 0 -0.
06
φ6-
0.00
2-
0.01
0
R0.2max
9
φ6-
0.00
2-
0.01
0
R0.2max
9
φ4.
5h6
0 -0.
008
φ6-0
.001
-0.0
06
30
22.5 7.5
7
φ9.
5h8
0 -0.
022 M6×0.75
30°×0.5
8 0-0.2
R0.2max
3
74
L5
L5
L4=L5ー41
L4=L5ー50
L5
L5
L4
L4=L5ー50
A-type B-type C-type
D-type : Other than the above. 上記以外の形状
*Please refer to page A316 for stainless steel type.※ステンレスタイプはぺージA316をご参照ください。
A299 A300
ボー
ルね
じBall Scresw
標準
在庫
品
SRT/SSRTシリ
ーズ
Standard products in stock SRT/SSRT series
ボー
ルね
じBall Scresw
標準
在庫
品
SRT/SSRTシリ
ーズ
Standard products in stock SRT/SSRT series
Unit(単位):mm
Ball Screw Modelボールねじ型番
Travelストローク
Grade精度
Shaft lengthねじ軸長さ
Lead accuracyリード精度
Total Run-out全振れ
Axialplay
軸方向すきま
PreloadTorque予圧トルク
Nm
Basic Load Rating基本定格荷重 N
L1 L2 L3
Travel deviation代表移動量誤差
ep
Variation変動V300
Dynamic動定格荷重
Ca
Static静定格荷重
Coa
SRT0801K-171R220C7 150 Ct7 171 175 220 ±0.03 ー 0.080 ~0.020ー 650 1300
SRT0801K-171R220C10 150 Ct10 171 175 220 ±0.11 ー 0.160 ~0.050
Note )Please refer to page A287 for order code of end-journal machining. 注)追加工の呼び番号指定方法はぺージA287をご参照ください。
Unit(単位):mm
Ball Screw Specifications 諸元
Ball size ボール径 φ0.8
Number of thread 条数 1
Thread direction 巻方向 Right 右
Shaft root dia. ねじ軸谷径 φ7.3
Number of circuit 循環数 1×3
Material材質
Shaft 軸 S55C+SUS303
Nut ナット SCM415H
Surface hardnessねじ部表面硬度
HRC58~(Thread area)
Anti-rust treatment防錆処理
Anti-rust oil防錆油
下表参照see table below
G
G
4
C0.5
45
φ11
.7
15
(11) 4
C0.5
φ13-
0.05
-0.
10 30°
17
PCD 20
φ26
4-φ3.4
30°
(φ
7.9)
4
L3
L2
L1
Standard products in stock SRT series標準在庫品 SRTシリーズ
SRT0801K
Support-unit Recommendation推奨サポートユニット
Supported-side 支持側 : MSU-6CS/6GSFixed-side 固定側 : MSU-6C/6G
L4:Thread length after end-journal machining. 追加工後のねじ部長さL5:Total length after end-journal machining. 追加工後全長
End-journal profile 端末加工形状 Supported-side 支持側
Shaft dia.(軸径)φ8 Lead(リード)1mm Ct7&Ct10
Fixed-side 固定側A11-SRT08 journal
6.8 +0.1 0
0.8+0.1 0
φ5.
7 0 -0.
06
φ6-
0.00
2-
0.01
0
R0.2max
9
φ6-
0.00
2-
0.01
0
R0.2max
9
φ4.
5h6
0 -0.
008
φ6-0
.001
-0.0
06
30
22.5 7.5
7
φ9.
5h8
0 -0.
022 M6×0.75
30°×0.5
8 0-0.2
R0.2max
3
74
L5
L5
L4=L5ー41
L4=L5ー50
L5
L5
L4
L4=L5ー50
A-type B-type C-type
D-type : Other than the above. 上記以外の形状
Compact Nut / コンパクトナット
Unit(単位):mm
Ball Screw Modelボールねじ型番
Travelストローク
Grade精度
Shaft lengthねじ軸長さ
Lead accuracyリード精度
Total Run-out全振れ
Axialplay
軸方向すきま
PreloadTorque予圧トルク
Nm
Basic Load Rating基本定格荷重 N
L1 L2 L3
Travel deviation代表移動量誤差
ep
Variation変動V300
Dynamic動定格荷重
Ca
Static静定格荷重
Coa
SRT0802-196R270C7 170 Ct7 196 200 270 ±0.03 ー 0.080~0.020
ー 2400 4100SRT0802-356R430C7 330 Ct7 356 360 430 ±0.06 0.05 0.120
SRT0802-196R270C10 170 Ct10 196 200 270 ±0.13 ー 0.160~0.050
SRT0802-356R430C10 330 Ct10 356 360 430 ±0.24 0.21 0.240
Note )Please refer to page A287 for order code of end-journal machining. 注)追加工の呼び番号指定方法はぺージA287をご参照ください。
Unit(単位):mm
Ball Screw Specifications 諸元
Ball size ボール径 φ1.5875
Number of thread 条数 1
Thread direction 巻方向 Right 右
Shaft root dia. ねじ軸谷径 φ6.6
Number of circuit 循環数 3.7×1
Material材質
Shaft 軸 SCM415H+SUS303
Nut ナット SCM415H
Surface hardnessねじ部表面硬度
HRC58~(Thread area)
Anti-rust treatment防錆処理
Anti-rust oil防錆油
A11-SRT0802
下表参照see table below
G
G
5
C0.5
70
φ14
.2
22
PCD 29
30°30°
4-φ4.524
(19)
φ20-
0.05
-0.
10
C0.5
φ37
(φ
7.7)
4
L3
L2
L1
Standard products in stock SRT series標準在庫品 SRTシリーズ
SRT0802
Support-unit Recommendation推奨サポートユニット
Supported-side 支持側 : MSU-6CS/6GSFixed-side 固定側 : MSU-6C/6G
L4:Thread length after end-journal machining. 追加工後のねじ部長さL5:Total length after end-journal machining. 追加工後全長
End-journal profile 端末加工形状 Supported-side 支持側
Shaft dia.(軸径)φ8 Lead(リード)2mm Ct7&Ct10
Fixed-side 固定側A11-SRT08 journal
6.8 +0.1 0
0.8+0.1 0
φ5.
7 0 -0.
06
φ6-
0.00
2-
0.01
0
R0.2max
9
φ6-
0.00
2-
0.01
0
R0.2max
9
φ4.
5h6
0 -0.
008
φ6-0
.001
-0.0
06
30
22.5 7.5
7
φ9.
5h8
0 -0.
022 M6×0.75
30°×0.5
8 0-0.2
R0.2max
3
74
L5
L5
L4=L5ー41
L4=L5ー50
L5
L5
L4
L4=L5ー50
A-type B-type C-type
D-type : Other than the above. 上記以外の形状
*Please refer to page A317 for stainless steel type.※ステンレスタイプはぺージA317をご参照ください。
A301 A302
ボー
ルね
じBall Scresw
標準
在庫
品
SRT/SSRTシリ
ーズ
Standard products in stock SRT/SSRT series
ボー
ルね
じBall Scresw
標準
在庫
品
SRT/SSRTシリ
ーズ
Standard products in stock SRT/SSRT series
Unit(単位):mm
Ball Screw Modelボールねじ型番
Travelストローク
Grade精度
Shaft lengthねじ軸長さ
Lead accuracyリード精度
Total Run-out全振れ
Axialplay
軸方向すきま
PreloadTorque予圧トルク
Nm
Basic Load Rating基本定格荷重 N
L1 L2 L3
Travel deviation代表移動量誤差
ep
Variation変動V300
Dynamic動定格荷重
Ca
Static静定格荷重
Coa
SRT0802K-171R220C7 145 Ct7 171 175 220 ±0.03 ー 0.080 ~0.020ー 1300 2300
SRT0802K-171R220C10 145 Ct10 171 175 220 ±0.11 ー 0.160 ~0.050
Note )Please refer to page A287 for order code of end-journal machining. 注)追加工の呼び番号指定方法はぺージA287をご参照ください。
Unit(単位):mm
Ball Screw Specifications 諸元
Ball size ボール径 φ1.2
Number of thread 条数 1
Thread direction 巻方向 Right 右
Shaft root dia. ねじ軸谷径 φ7.0
Number of circuit 循環数 1×3
Material材質
Shaft 軸 S55C+SUS303
Nut ナット SCM415H
Surface hardnessねじ部表面硬度
HRC58~(Thread area)
Anti-rust treatment防錆処理
Anti-rust oil防錆油
下表参照see table below
G
G
4
C0.5
45
φ11
.7
19
PCD 22
30°30°
4-φ3.418
(14)φ
15-
0.05
-0.
10
C0.5
φ28
(φ
7.9)
4
L3
L2
L1
Standard products in stock SRT series標準在庫品 SRTシリーズ
SRT0802K
Support-unit Recommendation推奨サポートユニット
Supported-side 支持側 : MSU-6CS/6GSFixed-side 固定側 : MSU-6C/6G
L4:Thread length after end-journal machining. 追加工後のねじ部長さL5:Total length after end-journal machining. 追加工後全長
End-journal profile 端末加工形状 Supported-side 支持側
Shaft dia.(軸径)φ8 Lead(リード)2mm Ct7&Ct10
Unit(単位):mm
Ball Screw Modelボールねじ型番
Travelストローク
Grade精度
Shaft lengthねじ軸長さ
Lead accuracyリード精度
Total Run-out全振れ
Axialplay
軸方向すきま
PreloadTorque予圧トルク
Nm
Basic Load Rating基本定格荷重 N
L1 L2 L3
Travel deviation代表移動量誤差
ep
Variation変動V300
Dynamic動定格荷重
Ca
Static静定格荷重
Coa
SRT0802.5-196R270C7 180 Ct7 196 200 270 ±0.03 ー 0.080~0.020
ー 1850 3000SRT0802.5-356R430C7 340 Ct7 356 360 430 ±0.06 0.05 0.120
SRT0802.5-196R270C10 180 Ct10 196 200 270 ±0.13 ー 0.160~0.050
SRT0802.5-356R430C10 340 Ct10 356 360 430 ±0.24 0.21 0.240
Note )Please refer to page A287 for order code of end-journal machining. 注)追加工の呼び番号指定方法はぺージA287をご参照ください。
Unit(単位):mm
Ball Screw Specifications 諸元
Ball size ボール径 φ1.5875
Number of thread 条数 1
Thread direction 巻方向 Right 右
Shaft root dia. ねじ軸谷径 φ6.3
Number of circuit 循環数 2.7×1
Material材質
Shaft 軸 SCM415H+SUS303
Nut ナット SCM415H
Surface hardnessねじ部表面硬度
HRC58~(Thread area)
Anti-rust treatment防錆処理
Anti-rust oil防錆油
A11-SRT0802.5
下表参照see table below
G
G
C0.5
70
φ14
.2
4
φ16-
0.05
-0.
10
C0.5
18
4-φ3.4
30° 30°
PCD 23
φ29
16
(12)
(φ
7.4)
4
L3
L2
L1
Standard products in stock SRT series標準在庫品 SRTシリーズ
SRT0802.5
Support-unit Recommendation推奨サポートユニット
Supported-side 支持側 : MSU-6CS/6GSFixed-side 固定側 : MSU-6C/6G
L4:Thread length after end-journal machining. 追加工後のねじ部長さL5:Total length after end-journal machining. 追加工後全長
End-journal profile 端末加工形状 Supported-side 支持側
Shaft dia.(軸径)φ8 Lead(リード)2.5mm Ct7&Ct10
Fixed-side 固定側 Fixed-side 固定側A11-SRT08 journal
6.8 +0.1 0
0.8+0.1 0
φ5.
7 0 -0.
06
φ6-
0.00
2-
0.01
0
R0.2max
9
φ6-
0.00
2-
0.01
0
R0.2max
9
φ4.
5h6
0 -0.
008
φ6-0
.001
-0.0
06
30
22.5 7.5
7
φ9.
5h8
0 -0.
022 M6×0.75
30°×0.5
8 0-0.2
R0.2max
3
74
L5
L5
L4=L5ー41
L4=L5ー50
L5
L5
L4
L4=L5ー50
A-type B-type C-type
A11-SRT08 journal
6.8 +0.1 0
0.8+0.1 0
φ5.
7 0 -0.
06
φ6-
0.00
2-
0.01
0
R0.2max
9
φ6-
0.00
2-
0.01
0
R0.2max
9
φ4.
5h6
0 -0.
008
φ6-0
.001
-0.0
06
30
22.5 7.5
7
φ9.
5h8
0 -0.
022 M6×0.75
30°×0.5
8 0-0.2
R0.2max
3
74
L5
L5
L4=L5ー41
L4=L5ー50
L5
L5
L4
L4=L5ー50
A-type B-type C-type
D-type : Other than the above. 上記以外の形状 D-type : Other than the above. 上記以外の形状
Compact Nut / コンパクトナット
A303 A304
ボー
ルね
じBall Scresw
標準
在庫
品
SRT/SSRTシリ
ーズ
Standard products in stock SRT/SSRT series
ボー
ルね
じBall Scresw
標準
在庫
品
SRT/SSRTシリ
ーズ
Standard products in stock SRT/SSRT series
Unit(単位):mm
Ball Screw Modelボールねじ型番
Travelストローク
Grade精度
Shaft lengthねじ軸長さ
Lead accuracyリード精度
Total Run-out全振れ
Axialplay
軸方向すきま
PreloadTorque予圧トルク
Nm
Basic Load Rating基本定格荷重 N
L1 L2 L3
Travel deviation代表移動量誤差
ep
Variation変動V300
Dynamic動定格荷重
Ca
Static静定格荷重
Coa
SRT0805-196R270C7 165 Ct7 196 200 270 ±0.03 ー 0.080~0.020
ー 1850 3000SRT0805-356R430C7 325 Ct7 356 360 430 ±0.06 0.05 0.120
SRT0805-196R270C10 165 Ct10 196 200 270 ±0.13 ー 0.160~0.050
SRT0805-356R430C10 325 Ct10 356 360 430 ±0.24 0.21 0.240
Note )Please refer to page A287 for order code of end-journal machining. 注)追加工の呼び番号指定方法はぺージA287をご参照ください。
Unit(単位):mm
Ball Screw Specifications 諸元
Ball size ボール径 φ1.5875
Number of thread 条数 1
Thread direction 巻方向 Right 右
Shaft root dia. ねじ軸谷径 φ6.6
Number of circuit 循環数 2.7×1
Material材質
Shaft 軸 SCM415H+SUS303
Nut ナット SCM415H
Surface hardnessねじ部表面硬度
HRC58~(Thread area)
Anti-rust treatment防錆処理
Anti-rust oil防錆油
A11-SRT0805
下表参照see table below
G
G
C0.5
70
φ14
.2
(φ
7.8)
φ31
4
φ18-
0.05
-0.
10
28
(24)
C0.5
PCD 25
30°
20
4-φ3.4
30°
4
L3
L2
L1
Standard products in stock SRT series標準在庫品 SRTシリーズ
SRT0805
Support-unit Recommendation推奨サポートユニット
Supported-side 支持側 : MSU-6CS/6GSFixed-side 固定側 : MSU-6C/6G
L4:Thread length after end-journal machining. 追加工後のねじ部長さL5:Total length after end-journal machining. 追加工後全長
End-journal profile 端末加工形状 Supported-side 支持側
Shaft dia.(軸径)φ8 Lead(リード)5mm Ct7&Ct10
Unit(単位):mm
Ball Screw Modelボールねじ型番
Travelストローク
Grade精度
Shaft lengthねじ軸長さ
Lead accuracyリード精度
Total Run-out全振れ
Axialplay
軸方向すきま
PreloadTorque予圧トルク
Nm
Basic Load Rating基本定格荷重 N
L1 L2 L3
Travel deviation代表移動量誤差
ep
Variation変動V300
Dynamic動定格荷重
Ca
Static静定格荷重
Coa
SRT0808-196R270C7 175 Ct7 196 200 270 ±0.03 ー 0.080~0.020
ー 2200 3800SRT0808-356R430C7 335 Ct7 356 360 430 ±0.06 0.05 0.120
SRT0808-196R270C10 175 Ct10 196 200 270 ±0.13 ー 0.160~0.050
SRT0808-356R430C10 335 Ct10 356 360 430 ±0.24 0.21 0.240
Note )Please refer to page A287 for order code of end-journal machining. 注)追加工の呼び番号指定方法はぺージA287をご参照ください。
Unit(単位):mm
Ball Screw Specifications 諸元
Ball size ボール径 φ1.5875
Number of thread 条数 2
Thread direction 巻方向 Right 右
Shaft root dia. ねじ軸谷径 φ6.7
Number of circuit 循環数 1.6×2
Material材質
Shaft 軸 SCM415H+SUS303
Nut ナット SCM415H
Surface hardnessねじ部表面硬度
HRC58~(Thread area)
Anti-rust treatment防錆処理
Anti-rust oil防錆油
A11-SRT0808
下表参照see table below
G
G
C0.5
70
φ14
.2
φ31φ
18-
0.05
-0.
10
(φ
7.9)
4(10)
20
PCD 25
20
4-φ3.4
30° 30°
4
L3
L2
L1
Standard products in stock SRT series標準在庫品 SRTシリーズ
SRT0808
Support-unit Recommendation推奨サポートユニット
Supported-side 支持側 : MSU-6CS/6GSFixed-side 固定側 : MSU-6C/6G
L4:Thread length after end-journal machining. 追加工後のねじ部長さL5:Total length after end-journal machining. 追加工後全長
End-journal profile 端末加工形状 Supported-side 支持側
Shaft dia.(軸径)φ8 Lead(リード)8mm Ct7&Ct10
Fixed-side 固定側 Fixed-side 固定側A11-SRT08 journal
6.8 +0.1 0
0.8+0.1 0
φ5.
7 0 -0.
06
φ6-
0.00
2-
0.01
0
R0.2max
9
φ6-
0.00
2-
0.01
0
R0.2max
9
φ4.
5h6
0 -0.
008
φ6-0
.001
-0.0
06
30
22.5 7.5
7
φ9.
5h8
0 -0.
022 M6×0.75
30°×0.5
8 0-0.2
R0.2max
3
74
L5
L5
L4=L5ー41
L4=L5ー50
L5
L5
L4
L4=L5ー50
A-type B-type C-type
A11-SRT08 journal
6.8 +0.1 0
0.8+0.1 0
φ5.
7 0 -0.
06
φ6-
0.00
2-
0.01
0
R0.2max
9
φ6-
0.00
2-
0.01
0
R0.2max
9
φ4.
5h6
0 -0.
008
φ6-0
.001
-0.0
06
30
22.5 7.5
7
φ9.
5h8
0 -0.
022 M6×0.75
30°×0.5
8 0-0.2
R0.2max
3
74
L5
L5
L4=L5ー41
L4=L5ー50
L5
L5
L4
L4=L5ー50
A-type B-type C-type
D-type : Other than the above. 上記以外の形状 D-type : Other than the above. 上記以外の形状
A305 A306
ボー
ルね
じBall Scresw
標準
在庫
品
SRT/SSRTシリ
ーズ
Standard products in stock SRT/SSRT series
ボー
ルね
じBall Scresw
標準
在庫
品
SRT/SSRTシリ
ーズ
Standard products in stock SRT/SSRT series
Unit(単位):mm
Ball Screw Modelボールねじ型番
Travelストローク
Grade精度
Shaft lengthねじ軸長さ
Lead accuracyリード精度
Total Run-out全振れ
Axialplay
軸方向すきま
PreloadTorque予圧トルク
Nm
Basic Load Rating基本定格荷重 N
L1 L2 L3
Travel deviation代表移動量誤差
ep
Variation変動V300
Dynamic動定格荷重
Ca
Static静定格荷重
Coa
SRT0812-196R270C7 165 Ct7 196 200 270 ±0.03 ー 0.080~0.020
ー 2200 4000SRT0812-356R430C7 325 Ct7 356 360 430 ±0.06 0.05 0.120
SRT0812-196R270C10 165 Ct10 196 200 270 ±0.13 ー 0.160~0.050
SRT0812-356R430C10 325 Ct10 356 360 430 ±0.24 0.21 0.240
Note )Please refer to page A287 for order code of end-journal machining. 注)追加工の呼び番号指定方法はぺージA287をご参照ください。
Unit(単位):mm
Ball Screw Specifications 諸元
Ball size ボール径 φ1.5875
Number of thread 条数 2
Thread direction 巻方向 Right 右
Shaft root dia. ねじ軸谷径 φ6.7
Number of circuit 循環数 1.6×2
Material材質
Shaft 軸 SCM415H+SUS303
Nut ナット SCM415H
Surface hardnessねじ部表面硬度
HRC58~(Thread area)
Anti-rust treatment防錆処理
Anti-rust oil防錆油
A11-SRT0812
下表参照see table below
G
G
C0.5
70
φ14
.2
(φ
7.9)
4
PCD 25
20
4-φ3.4
30° 30°
φ31φ
18-
0.05
-0.
10
27
(17)
4
L3
L2
L1
Standard products in stock SRT series標準在庫品 SRTシリーズ
SRT0812
Support-unit Recommendation推奨サポートユニット
Supported-side 支持側 : MSU-6CS/6GSFixed-side 固定側 : MSU-6C/6G
L4:Thread length after end-journal machining. 追加工後のねじ部長さL5:Total length after end-journal machining. 追加工後全長
End-journal profile 端末加工形状 Supported-side 支持側
Shaft dia.(軸径)φ8 Lead(リード)12mm Ct7&Ct10
Fixed-side 固定側A11-SRT08 journal
6.8 +0.1 0
0.8+0.1 0
φ5.
7 0 -0.
06
φ6-
0.00
2-
0.01
0
R0.2max
9
φ6-
0.00
2-
0.01
0
R0.2max
9
φ4.
5h6
0 -0.
008
φ6-0
.001
-0.0
06
30
22.5 7.5
7
φ9.
5h8
0 -0.
022 M6×0.75
30°×0.5
8 0-0.2
R0.2max
3
74
L5
L5
L4=L5ー41
L4=L5ー50
L5
L5
L4
L4=L5ー50
A-type B-type C-type
D-type : Other than the above. 上記以外の形状 Unit(単位):mm
Ball Screw Modelボールねじ型番
Travelストローク
Grade精度
Shaft lengthねじ軸長さ
Lead accuracyリード精度
Total Run-out全振れ
Axialplay
軸方向すきま
PreloadTorque予圧トルク
Nm
Basic Load Rating基本定格荷重 N
L1 L2 L3
Travel deviation代表移動量誤差
ep
Variation変動V300
Dynamic動定格荷重
Ca
Static静定格荷重
Coa
SRT1002-196R270C7 170 Ct7 196 200 270 ±0.03 ー 0.080~0.020
ー 2700 5300SRT1002-396R470C7 370 Ct7 396 400 470 ±0.06 0.05 0.120
SRT1002-196R270C10 170 Ct10 196 200 270 ±0.13 ー 0.160~0.050
SRT1002-396R470C10 370 Ct10 396 400 470 ±0.27 0.21 0.240
Note )Please refer to page A287 for order code of end-journal machining. 注)追加工の呼び番号指定方法はぺージA287をご参照ください。
Unit(単位):mm
Ball Screw Specifications 諸元
Ball size ボール径 φ1.5875
Number of thread 条数 1
Thread direction 巻方向 Right 右
Shaft root dia. ねじ軸谷径 φ8.6
Number of circuit 循環数 3.7×1
Material材質
Shaft 軸 SCM415H+SUS303
Nut ナット SCM415H
Surface hardnessねじ部表面硬度
HRC58~(Thread area)
Anti-rust treatment防錆処理
Anti-rust oil防錆油
A11-SRT1002
下表参照see table below
G
GC0.5
25
30°
PCD 32
φ40
24
(19) 5
4-φ4.5
30°
φ23-
0.05
-0.
10
(φ
9.7)
C0.5
70
φ14
.2
4
L3
L2
L1
Standard products in stock SRT series標準在庫品 SRTシリーズ
SRT1002
Support-unit Recommendation推奨サポートユニット
Supported-side 支持側 : MSU-8CS/8GSFixed-side 固定側 : MSU-8C/8G
L4:Thread length after end-journal machining. 追加工後のねじ部長さL5:Total length after end-journal machining. 追加工後全長
End-journal profile 端末加工形状 Supported-side 支持側
Shaft dia.(軸径)φ10 Lead(リード)2mm Ct7&Ct10
Fixed-side 固定側A11-SRT10 journal
6.8+0.1 0
0.8+0.1 0
φ5.
7 0 -0.
06
φ6-
0.00
2-
0.01
0
R0.2max
9
30°×0.5
φ6h
6 0 -0.
008
φ8-
0.00
2-
0.00
8
φ11
.5h8
0 -0.
027
37
27 10
9
R0.2max
M8×1.010 0
-0.2
4
8
φ6-
0.00
2-
0.01
0
R0.2max9
4
L5
L4=L5ー49
L5
L4=L5ー58
L5
L5
L4
L4=L5ー58
A-type B-type C-type
D-type : Other than the above. 上記以外の形状
*Please refer to page A318 for stainless steel type.※ステンレスタイプはぺージA318をご参照ください。
A307 A308
ボー
ルね
じBall Scresw
標準
在庫
品
SRT/SSRTシリ
ーズ
Standard products in stock SRT/SSRT series
ボー
ルね
じBall Scresw
標準
在庫
品
SRT/SSRTシリ
ーズ
Standard products in stock SRT/SSRT series
Unit(単位):mm
Ball Screw Modelボールねじ型番
Travelストローク
Grade精度
Shaft lengthねじ軸長さ
Lead accuracyリード精度
Total Run-out全振れ
Axialplay
軸方向すきま
PreloadTorque予圧トルク
Nm
Basic Load Rating基本定格荷重 N
L1 L2 L3
Travel deviation代表移動量誤差
ep
Variation変動V300
Dynamic動定格荷重
Ca
Static静定格荷重
Coa
SRT1002K-201R260C7 175 Ct7 201 205 260 ±0.03 ー 0.080 ~0.020ー 1450 3000
SRT1002K-201R260C10 175 Ct10 201 205 260 ±0.14 ー 0.160 ~0.050
Note )Please refer to page A287 for order code of end-journal machining. 注)追加工の呼び番号指定方法はぺージA287をご参照ください。
Unit(単位):mm
Ball Screw Specifications 諸元
Ball size ボール径 φ1.2
Number of thread 条数 1
Thread direction 巻方向 Right 右
Shaft root dia. ねじ軸谷径 φ9.0
Number of circuit 循環数 1×3
Material材質
Shaft 軸 S55C+SUS303
Nut ナット SCM415H
Surface hardnessねじ部表面硬度
HRC58~(Thread area)
Anti-rust treatment防錆処理
Anti-rust oil防錆油
Standard products in stock SRT series標準在庫品 SRTシリーズ
SRT1002K
Support-unit Recommendation推奨サポートユニット
Supported-side 支持側 : MSU-8CS/8GSFixed-side 固定側 : MSU-8C/8G
L4:Thread length after end-journal machining. 追加工後のねじ部長さL5:Total length after end-journal machining. 追加工後全長
End-journal profile 端末加工形状 Supported-side 支持側
Shaft dia.(軸径)φ10 Lead(リード)2mm Ct7&Ct10
Fixed-side 固定側A11-SRT10 journal
6.8+0.1 0
0.8+0.1 0
φ5.
7 0 -0.
06
φ6-
0.00
2-
0.01
0
R0.2max
9
30°×0.5
φ6h
6 0 -0.
008
φ8-
0.00
2-
0.00
8
φ11
.5h8
0 -0.
027
37
27 10
9
R0.2max
M8×1.010 0
-0.2
4
8
φ6-
0.00
2-
0.01
0
R0.2max9
4
L5
L4=L5ー49
L5
L4=L5ー58
L5
L5
L4
L4=L5ー58
A-type B-type C-type
Unit(単位):mm
Ball Screw Modelボールねじ型番
Travelストローク
Grade精度
Shaft lengthねじ軸長さ
Lead accuracyリード精度
Total Run-out全振れ
Axialplay
軸方向すきま
PreloadTorque予圧トルク
Nm
Basic Load Rating基本定格荷重 N
L1 L2 L3
Travel deviation代表移動量誤差
ep
Variation変動V300
Dynamic動定格荷重
Ca
Static静定格荷重
Coa
SRT1005-196R270C7 170 Ct7 196 200 270 ±0.03 ー 0.080~0.020
ー 3000 5200SRT1005-396R470C7 370 Ct7 396 400 470 ±0.06 0.05 0.120
SRT1005-196R270C10 170 Ct10 196 200 270 ±0.13 ー 0.160~0.050
SRT1005-396R470C10 370 Ct10 396 400 470 ±0.27 0.21 0.240
Note )Please refer to page A287 for order code of end-journal machining. 注)追加工の呼び番号指定方法はぺージA287をご参照ください。
Unit(単位):mm
Ball Screw Specifications 諸元
Ball size ボール径 φ2.0
Number of thread 条数 1
Thread direction 巻方向 Right 右
Shaft root dia. ねじ軸谷径 φ8.2
Number of circuit 循環数 2.7×1
Material材質
Shaft 軸 SCM415H+SUS303
Nut ナット SCM415H
Surface hardnessねじ部表面硬度
HRC58~(Thread area)
Anti-rust treatment防錆処理
Anti-rust oil防錆油
A11-SRT1005
下表参照see table below
G
G
25
30°
PCD 32
4-φ4.5
30°
C0.5
70
φ14
.2
4
26
(21) 5
φ40φ
23-
0.05
-0.
10
C0.5
(φ
9.6)
L3
L2
L1
Standard products in stock SRT series標準在庫品 SRTシリーズ
SRT1005
Support-unit Recommendation推奨サポートユニット
Supported-side 支持側 : MSU-8CS/8GSFixed-side 固定側 : MSU-8C/8G
L4:Thread length after end-journal machining. 追加工後のねじ部長さL5:Total length after end-journal machining. 追加工後全長
End-journal profile 端末加工形状 Supported-side 支持側
Shaft dia.(軸径)φ10 Lead(リード)5mm Ct7&Ct10
Fixed-side 固定側A11-SRT10 journal
6.8+0.1 0
0.8+0.1 0
φ5.
7 0 -0.
06
φ6-
0.00
2-
0.01
0
R0.2max
9
30°×0.5
φ6h
6 0 -0.
008
φ8-
0.00
2-
0.00
8
φ11
.5h8
0 -0.
027
37
27 10
9
R0.2max
M8×1.010 0
-0.2
4
8
φ6-
0.00
2-
0.01
0
R0.2max9
4
L5
L4=L5ー49
L5
L4=L5ー58
L5
L5
L4
L4=L5ー58
A-type B-type C-type
下表参照see table below
G
G C0.5
21
30°
PCD 26
φ34
19
(14) 5
4-φ4.5
30°
φ17-
0.05
-0.
10
(φ
9.9)
C0.5
55
φ11
.7
4
L3
L2
L1
D-type : Other than the above. 上記以外の形状 D-type : Other than the above. 上記以外の形状
Compact Nut / コンパクトナット
A309 A310
ボー
ルね
じBall Scresw
標準
在庫
品
SRT/SSRTシリ
ーズ
Standard products in stock SRT/SSRT series
ボー
ルね
じBall Scresw
標準
在庫
品
SRT/SSRTシリ
ーズ
Standard products in stock SRT/SSRT series
Unit(単位):mm
Ball Screw Modelボールねじ型番
Travelストローク
Grade精度
Shaft lengthねじ軸長さ
Lead accuracyリード精度
Total Run-out全振れ
Axialplay
軸方向すきま
PreloadTorque予圧トルク
Nm
Basic Load Rating基本定格荷重 N
L1 L2 L3
Travel deviation代表移動量誤差
ep
Variation変動V300
Dynamic動定格荷重
Ca
Static静定格荷重
Coa
SRT1010-196R270C7 170 Ct7 196 200 270 ±0.03 ー 0.080~0.020
ー 3300 5900SRT1010-396R470C7 370 Ct7 396 400 470 ±0.06 0.05 0.120
SRT1010-196R270C10 170 Ct10 196 200 270 ±0.13 ー 0.160~0.050
SRT1010-396R470C10 370 Ct10 396 400 470 ±0.27 0.21 0.240
Note )Please refer to page A287 for order code of end-journal machining. 注)追加工の呼び番号指定方法はぺージA287をご参照ください。
Unit(単位):mm
Ball Screw Specifications 諸元
Ball size ボール径 φ2.0
Number of thread 条数 2
Thread direction 巻方向 Right 右
Shaft root dia. ねじ軸谷径 φ8.4
Number of circuit 循環数 1.6×2
Material材質
Shaft 軸 SCM415H+SUS303
Nut ナット SCM415H
Surface hardnessねじ部表面硬度
HRC58~(Thread area)
Anti-rust treatment防錆処理
Anti-rust oil防錆油
A11-SRT1010
下表参照see table below
G
G
4
70
25
30°
PCD 32
5
4-φ4.5
30°
C0.5
φ14
.2
φ40φ
23-
0.05
-0.
10
24
(13)
(φ
9.8)
L3
L2
L1
Standard products in stock SRT series標準在庫品 SRTシリーズ
SRT1010
Support-unit Recommendation推奨サポートユニット
Supported-side 支持側 : MSU-8CS/8GSFixed-side 固定側 : MSU-8C/8G
L4:Thread length after end-journal machining. 追加工後のねじ部長さL5:Total length after end-journal machining. 追加工後全長
End-journal profile 端末加工形状 Supported-side 支持側
Shaft dia.(軸径)φ10 Lead(リード)10mm Ct7&Ct10
Fixed-side 固定側A11-SRT10 journal
6.8+0.1 0
0.8+0.1 0
φ5.
7 0 -0.
06
φ6-
0.00
2-
0.01
0
R0.2max
9
30°×0.5
φ6h
6 0 -0.
008
φ8-
0.00
2-
0.00
8
φ11
.5h8
0 -0.
027
37
27 10
9
R0.2max
M8×1.010 0
-0.2
4
8
φ6-
0.00
2-
0.01
0
R0.2max9
4
L5
L4=L5ー49
L5
L4=L5ー58
L5
L5
L4
L4=L5ー58
A-type B-type C-type
Unit(単位):mm
Ball Screw Modelボールねじ型番
Travelストローク
Grade精度
Shaft lengthねじ軸長さ
Lead accuracyリード精度
Total Run-out全振れ
Axialplay
軸方向すきま
PreloadTorque予圧トルク
Nm
Basic Load Rating基本定格荷重 N
L1 L2 L3
Travel deviation代表移動量誤差
ep
Variation変動V300
Dynamic動定格荷重
Ca
Static静定格荷重
Coa
SRT1015-196R270C7 160 Ct7 196 200 270 ±0.03 ー 0.080~0.020
ー 3300 6400SRT1015-396R470C7 360 Ct7 396 400 470 ±0.06 0.05 0.120
SRT1015-196R270C10 160 Ct10 196 200 270 ±0.13 ー 0.160~0.050
SRT1015-396R470C10 360 Ct10 396 400 470 ±0.27 0.21 0.240
Note )Please refer to page A287 for order code of end-journal machining. 注)追加工の呼び番号指定方法はぺージA287をご参照ください。
Unit(単位):mm
Ball Screw Specifications 諸元
Ball size ボール径 φ2.0
Number of thread 条数 2
Thread direction 巻方向 Right 右
Shaft root dia. ねじ軸谷径 φ8.4
Number of circuit 循環数 1.6×2
Material材質
Shaft 軸 SCM415H+SUS303
Nut ナット SCM415H
Surface hardnessねじ部表面硬度
HRC58~(Thread area)
Anti-rust treatment防錆処理
Anti-rust oil防錆油
A11-SRT1015
下表参照see table below
G
G
4 25
30°
PCD 32
5
4-φ4.5
30°
C0.5
70
φ14
.2
φ40φ
23-
0.05
-0.
10
33
(22)
(φ
9.8)
L3
L2
L1
Standard products in stock SRT series標準在庫品 SRTシリーズ
SRT1015
Support-unit Recommendation推奨サポートユニット
Supported-side 支持側 : MSU-8CS/8GSFixed-side 固定側 : MSU-8C/8G
L4:Thread length after end-journal machining. 追加工後のねじ部長さL5:Total length after end-journal machining. 追加工後全長
End-journal profile 端末加工形状 Supported-side 支持側
Shaft dia.(軸径)φ10 Lead(リード)15mm Ct7&Ct10
Fixed-side 固定側A11-SRT10 journal
6.8+0.1 0
0.8+0.1 0
φ5.
7 0 -0.
06
φ6-
0.00
2-
0.01
0
R0.2max
9
30°×0.5
φ6h
6 0 -0.
008
φ8-
0.00
2-
0.00
8
φ11
.5h8
0 -0.
027
37
27 10
9
R0.2max
M8×1.010 0
-0.2
4
8
φ6-
0.00
2-
0.01
0
R0.2max9
4
L5
L4=L5ー49
L5
L4=L5ー58
L5
L5
L4
L4=L5ー58
A-type B-type C-type
D-type : Other than the above. 上記以外の形状 D-type : Other than the above. 上記以外の形状
A311 A312
ボー
ルね
じBall Scresw
標準
在庫
品
SRT/SSRTシリ
ーズ
Standard products in stock SRT/SSRT series
ボー
ルね
じBall Scresw
標準
在庫
品
SRT/SSRTシリ
ーズ
Standard products in stock SRT/SSRT series
Unit(単位):mm
Ball Screw Modelボールねじ型番
Travelストローク
Grade精度
Shaft lengthねじ軸長さ
Lead accuracyリード精度
Total Run-out全振れ
Axialplay
軸方向すきま
PreloadTorque予圧トルク
Nm
Basic Load Rating基本定格荷重 N
L1 L2 L3
Travel deviation代表移動量誤差
ep
Variation変動V300
Dynamic動定格荷重
Ca
Static静定格荷重
Coa
SRT1020-196R270C7 170 Ct7 196 200 270 ±0.03 ー 0.080~0.020
ー 2100 4000SRT1020-396R470C7 370 Ct7 396 400 470 ±0.06 0.05 0.120
SRT1020-196R270C10 170 Ct10 196 200 270 ±0.13 ー 0.160~0.050
SRT1020-396R470C10 370 Ct10 396 400 470 ±0.27 0.21 0.240
Note )Please refer to page A287 for order code of end-journal machining. 注)追加工の呼び番号指定方法はぺージA287をご参照ください。
Unit(単位):mm
Ball Screw Specifications 諸元
Ball size ボール径 φ1.5875
Number of thread 条数 4
Thread direction 巻方向 Right 右
Shaft root dia. ねじ軸谷径 φ8.7
Number of circuit 循環数 0.7×4
Material材質
Shaft 軸 SCM415H+SUS303
Nut ナット SCM415H
Surface hardnessねじ部表面硬度
HRC58~(Thread area)
Anti-rust treatment防錆処理
Anti-rust oil防錆油
A11-SRT1020
下表参照see table below
G
G
4
70
C0.5
φ14
.2
φ37
23φ
20-
0.05
-0.
10
(φ
9.9)
30° 30°
PCD 29
4-φ4.5
22
(13) 5
L3
L2
L1
Standard products in stock SRT series標準在庫品 SRTシリーズ
SRT1020
Support-unit Recommendation推奨サポートユニット
Supported-side 支持側 : MSU-8CS/8GSFixed-side 固定側 : MSU-8C/8G
L4:Thread length after end-journal machining. 追加工後のねじ部長さL5:Total length after end-journal machining. 追加工後全長
End-journal profile 端末加工形状 Supported-side 支持側
Shaft dia.(軸径)φ10 Lead(リード)20mm Ct7&Ct10
Fixed-side 固定側A11-SRT10 journal
6.8+0.1 0
0.8+0.1 0
φ5.
7 0 -0.
06
φ6-
0.00
2-
0.01
0
R0.2max
9
30°×0.5
φ6h
6 0 -0.
008
φ8-
0.00
2-
0.00
8
φ11
.5h8
0 -0.
027
37
27 10
9
R0.2max
M8×1.010 0
-0.2
4
8
φ6-
0.00
2-
0.01
0
R0.2max9
4
L5
L4=L5ー49
L5
L4=L5ー58
L5
L5
L4
L4=L5ー58
A-type B-type C-type
A11-SRT12 journal
φ8h
6 0 -0.
009
φ10-
0.00
2-
0.00
8
30 15
M10×1.0
10R0.2max
30°×0.5
φ14
h8 0 -0.
027
5
12 0-0.25
4510
φ8-
0.00
4-
0.01
2
10
7.9 +0.1 0
0.9+0.1 0
R0.2max
φ7.
6 0 -0.
08
φ8-
0.00
4-
0.01
2
10
4
R0.2max
L5
L4=L5ー59
L5
L4=L5ー69
L5
L5
L4
L4=L5ー69
A-type B-type C-type
Unit(単位):mm
Ball Screw Modelボールねじ型番
Travelストローク
Grade精度
Shaft lengthねじ軸長さ
Lead accuracyリード精度
Total Run-out全振れ
Axialplay
軸方向すきま
PreloadTorque予圧トルク
Nm
Basic Load Rating基本定格荷重 N
L1 L2 L3
Travel deviation代表移動量誤差
ep
Variation変動V300
Dynamic動定格荷重
Ca
Static静定格荷重
Coa
SRT1202-196R270C7 170 Ct7 196 200 270 ±0.03 ー 0.080~0.020
ー 3000 6400SRT1202-396R470C7 370 Ct7 396 400 470 ±0.06 0.05 0.080
SRT1202-196R270C10 170 Ct10 196 200 270 ±0.13 ー 0.160~0.050
SRT1202-396R470C10 370 Ct10 396 400 470 ±0.27 0.21 0.160
Note )Please refer to page A287 for order code of end-journal machining. 注)追加工の呼び番号指定方法はぺージA287をご参照ください。
Unit(単位):mm
Ball Screw Specifications 諸元
Ball size ボール径 φ1.5875
Number of thread 条数 1
Thread direction 巻方向 Right 右
Shaft root dia. ねじ軸谷径 φ10.6
Number of circuit 循環数 3.7×1
Material材質
Shaft 軸 SCM415H+SUS303
Nut ナット SCM415H
Surface hardnessねじ部表面硬度
HRC58~(Thread area)
Anti-rust treatment防錆処理
Anti-rust oil防錆油
-0.
10
A11-SRT1202
下表参照see table below
G
G
4
70
5
C0.5
φ14
.2
27
φ25-
0.05
φ42
PCD 34
C0.5
24
(19) 30° 30°
4-φ4.5
(φ
11.7)
L3
L2
L1
Standard products in stock SRT series標準在庫品 SRTシリーズ
SRT1202
Support-unit Recommendation推奨サポートユニット
Supported-side 支持側 : ーFixed-side 固定側 : ー
L4:Thread length after end-journal machining. 追加工後のねじ部長さL5:Total length after end-journal machining. 追加工後全長
End-journal profile 端末加工形状 Supported-side 支持側
Shaft dia.(軸径)φ12 Lead(リード)2mm Ct7&Ct10
Fixed-side 固定側
D-type : Other than the above. 上記以外の形状 D-type : Other than the above. 上記以外の形状
A313 A314
ボー
ルね
じBall Scresw
標準
在庫
品
SRT/SSRTシリ
ーズ
Standard products in stock SRT/SSRT series
ボー
ルね
じBall Scresw
標準
在庫
品
SRT/SSRTシリ
ーズ
Standard products in stock SRT/SSRT series
A11-SRT12 journal
φ8h
6 0 -0.
009
φ10-
0.00
2-
0.00
8
30 15
M10×1.0
10R0.2max
30°×0.5φ
14h8
0 -0.
027
5
12 0-0.25
4510
φ8-
0.00
4-
0.01
2
10
7.9 +0.1 0
0.9+0.1 0
R0.2max
φ7.
6 0 -0.
08
φ8-
0.00
4-
0.01
2
10
4
R0.2max
L5
L4=L5ー59
L5
L4=L5ー69
L5
L5
L4
L4=L5ー69
A-type B-type C-type
Unit(単位):mm
Ball Screw Modelボールねじ型番
Travelストローク
Grade精度
Shaft lengthねじ軸長さ
Lead accuracyリード精度
Total Run-out全振れ
Axialplay
軸方向すきま
PreloadTorque予圧トルク
Nm
Basic Load Rating基本定格荷重 N
L1 L2 L3
Travel deviation代表移動量誤差
ep
Variation変動V300
Dynamic動定格荷重
Ca
Static静定格荷重
Coa
SRT1202K-271R335C7 245 Ct7 271 275 335 ±0.04 ー 0.080 ~0.020ー 1600 3700
SRT1202K-271R335C10 245 Ct10 271 275 335 ±0.19 ー 0.160 ~0.050
Note )Please refer to page A287 for order code of end-journal machining. 注)追加工の呼び番号指定方法はぺージA287をご参照ください。
Unit(単位):mm
Ball Screw Specifications 諸元
Ball size ボール径 φ1.2
Number of thread 条数 1
Thread direction 巻方向 Right 右
Shaft root dia. ねじ軸谷径 φ11.0
Number of circuit 循環数 1×3
Material材質
Shaft 軸 S55C+SUS303
Nut ナット SCM415H
Surface hardnessねじ部表面硬度
HRC58~(Thread area)
Anti-rust treatment防錆処理
Anti-rust oil防錆油
-0.
10
下表参照see table below
G
G
4
60
5
C0.5
φ14
.2
23
φ19-
0.05
φ36
PCD 28
C0.5
19
(14) 30° 30°
4-φ4.5
(φ
11.9)
L3
L2
L1
Standard products in stock SRT series標準在庫品 SRTシリーズ
SRT1202K
Support-unit Recommendation推奨サポートユニット
Supported-side 支持側 : ーFixed-side 固定側 : ー
L4:Thread length after end-journal machining. 追加工後のねじ部長さL5:Total length after end-journal machining. 追加工後全長
End-journal profile 端末加工形状 Supported-side 支持側
Shaft dia.(軸径)φ12 Lead(リード)2mm Ct7&Ct10
Unit(単位):mm
Ball Screw Modelボールねじ型番
Travelストローク
Grade精度
Shaft lengthねじ軸長さ
Lead accuracyリード精度
Total Run-out全振れ
Axialplay
軸方向すきま
PreloadTorque予圧トルク
Nm
Basic Load Rating基本定格荷重 N
L1 L2 L3
Travel deviation代表移動量誤差
ep
Variation変動V300
Dynamic動定格荷重
Ca
Static静定格荷重
Coa
SRT1210-196R270C7 165 Ct7 196 200 270 ±0.03 ー 0.080~0.020
ー 5100 9800SRT1210-396R470C7 365 Ct7 396 400 470 ±0.06 0.05 0.080
SRT1210-196R270C10 165 Ct10 196 200 270 ±0.13 ー 0.160~0.050
SRT1210-396R470C10 365 Ct10 396 400 470 ±0.27 0.21 0.160
Note )Please refer to page A287 for order code of end-journal machining. 注)追加工の呼び番号指定方法はぺージA287をご参照ください。
Unit(単位):mm
Ball Screw Specifications 諸元
Ball size ボール径 φ2.381
Number of thread 条数 2
Thread direction 巻方向 Right 右
Shaft root dia. ねじ軸谷径 φ10.2
Number of circuit 循環数 1.7×2
Material材質
Shaft 軸 SCM415H+SUS303
Nut ナット SCM415H
Surface hardnessねじ部表面硬度
HRC58~(Thread area)
Anti-rust treatment防錆処理
Anti-rust oil防錆油
A11-SRT1210
下表参照see table below
G
G
4
70
C0.5
φ14
.2
30° 30°
30
6(14.5)
φ24-
0.05
-0.
10
φ41
26
PCD 33
4-φ4.5
(φ
11.7
5)
L3
L2
L1
Standard products in stock SRT series標準在庫品 SRTシリーズ
SRT1210
Support-unit Recommendation推奨サポートユニット
Supported-side 支持側 : ーFixed-side 固定側 : ー
L4:Thread length after end-journal machining. 追加工後のねじ部長さL5:Total length after end-journal machining. 追加工後全長
End-journal profile 端末加工形状 Supported-side 支持側
Shaft dia.(軸径)φ12 Lead(リード)10mm Ct7&Ct10
Fixed-side 固定側 Fixed-side 固定側A11-SRT12 journal
φ8h
6 0 -0.
009
φ10-
0.00
2-
0.00
8
30 15
M10×1.0
10R0.2max
30°×0.5
φ14
h8 0 -0.
027
5
12 0-0.25
4510
φ8-
0.00
4-
0.01
2
10
7.9 +0.1 0
0.9+0.1 0
R0.2max
φ7.
6 0 -0.
08
φ8-
0.00
4-
0.01
2
10
4
R0.2max
L5
L4=L5ー59
L5
L4=L5ー69
L5
L5
L4
L4=L5ー69
A-type B-type C-type
D-type : Other than the above. 上記以外の形状 D-type : Other than the above. 上記以外の形状
Compact Nut / コンパクトナット
A315 A316
ボー
ルね
じBall Scresw
標準
在庫
品
SRT/SSRTシリ
ーズ
Standard products in stock SRT/SSRT series
ボー
ルね
じBall Scresw
標準
在庫
品
SRT/SSRTシリ
ーズ
Standard products in stock SRT/SSRT series
Unit(単位):mm
Ball Screw Modelボールねじ型番
Travelストローク
Grade精度
Shaft lengthねじ軸長さ
Lead accuracyリード精度 Total
Run-out全振れ
Axialplay
軸方向すきま
PreloadTorque予圧トルク
Nm
Basic Load Rating基本定格荷重 N
L1 L2 L3
Travel deviation代表移動量誤差
ep
Variation変動V300
Dynamic動定格荷重
Ca
Static静定格荷重
Coa
SSRT0601-146R220C7 125 Ct7 146 150 220 ±0.02 ー 0.080~0.020
ー 560 900SSRT0601-261R335C7 240 Ct7 261 265 335 ±0.04 ー 0.120
SSRT0601-146R220C10 125 Ct10 146 150 220 ±0.10 ー 0.160~0.050
SSRT0601-261R335C10 240 Ct10 261 265 335 ±0.18 ー 0.240
Note )Please refer to page A287 for order code of end-journal machining. 注)追加工の呼び番号指定方法はぺージA287をご参照ください。
Unit(単位):mm
Ball Screw Specifications 諸元
Ball size ボール径 φ0.8
Number of thread 条数 1
Thread direction 巻方向 Right 右
Shaft root dia. ねじ軸谷径 φ5.3
Number of circuit 循環数 3.7×1
Material材質
Shaft 軸 SUS440C+SUS303
Nut ナット SUS440C
Surface hardnessねじ部表面硬度
HRC55~(Thread area)
Anti-rust treatment防錆処理
Anti-rust oil防錆油
Support-unit Recommendation推奨サポートユニット
Supported-side 支持側 : MSU-5CS/5GSFixed-side 固定側 : MSU-5C/5G
G
下表参照see table below
G
70
φ9.
7
C0.5
(13) 4
C0.5
φ13
-0.0
5-0
.10
PCD 20
16
30°
17
φ26
(φ
5.85)
4-φ3.4
30°
4
L3
L2
L1
下表参照see table below
G
G
4
C0.5
70
φ14
.2
17
(13) 4
C0.5
φ16
-0.0
5-0
.10 30°
18
PCD 23
φ29
4-φ3.4
30°
(φ
7.85)
4
L3
L2
L1
L4=L5ー36
L5
R0.2max
8 L4=L5ー44
R0.2max
L4=L5ー44
φ8h
8 0 -0
.022
φ5-0
.001
-0.0
06
φ4h
6 0 -0
.008
19 6
6.5
M5×0.5
30°×0.5
R0.2max
3
7 0-0.2
25
L5
7L4
L5
L5
8
φ4
-0.0
02-0
.010
φ3.
7±
0.03
φ4
-0.0
02-0
.010
5.35±0.05
0.5+0.1 0
4
L4=L5ー41
L5 6.8 +0.1 0
0.8 +0.1 0
φ5.
7 0 -0
.06
φ6
-0.0
02-0
.010
R0.2max
9
L5
L4=L5ー50
φ6-0
.002
-0.0
10
R0.2max9
L5
L4=L5ー50
φ4.
5h6
0 -0.0
08
φ6-0
.001
-0.0
06
30
22.5 7.5
7
φ9.
5h8
0 -0.0
22 M6×0.75
30°×0.5
8 0-0.2
R0.2max
3
L5
7L4 4
Standard products in stock SSRT series標準在庫品 SSRTシリーズ
SSRT0601
L4:Thread length after end-journal machining. 追加工後のねじ部長さL5:Total length after end-journal machining. 追加工後全長
Shaft dia.(軸径)φ6 Lead(リード)1mm Ct7&Ct10Stainless ステンレス
Unit(単位):mm
Ball Screw Modelボールねじ型番
Travelストローク
Grade精度
Shaft lengthねじ軸長さ
Lead accuracyリード精度 Total
Run-out全振れ
Axialplay
軸方向すきま
PreloadTorque予圧トルク
Nm
Basic Load Rating基本定格荷重 N
L1 L2 L3
Travel deviation代表移動量誤差
ep
Variation変動V300
Dynamic動定格荷重
Ca
Static静定格荷重
Coa
SSRT0801-196R270C7 175 Ct7 196 200 270 ±0.03 ー 0.080~0.020
ー 630 1250SSRT0801-356R430C7 335 Ct7 356 360 430 ±0.06 0.05 0.120
SSRT0801-196R270C10 175 Ct10 196 200 270 ±0.13 ー 0.160~0.050
SSRT0801-356R430C10 335 Ct10 356 360 430 ±0.24 0.21 0.240
Note )Please refer to page A287 for order code of end-journal machining. 注)追加工の呼び番号指定方法はぺージA287をご参照ください。
Unit(単位):mm
Ball Screw Specifications 諸元
Ball size ボール径 φ0.8
Number of thread 条数 1
Thread direction 巻方向 Right 右
Shaft root dia. ねじ軸谷径 φ7.3
Number of circuit 循環数 3.7×1
Material材質
Shaft 軸 SUS440C+SUS303
Nut ナット SUS440C
Surface hardnessねじ部表面硬度
HRC55~(Thread area)
Anti-rust treatment防錆処理
Anti-rust oil防錆油
Support-unit Recommendation推奨サポートユニット
Supported-side 支持側 : MSU-6CS/6GSFixed-side 固定側 : MSU-6C/6G
Standard products in stock SSRT series標準在庫品 SSRTシリーズ
SSRT0801
L4:Thread length after end-journal machining. 追加工後のねじ部長さL5:Total length after end-journal machining. 追加工後全長
Shaft dia.(軸径)φ8 Lead(リード)1mm Ct7&Ct10Stainless ステンレス
A-type B-typeA-type B-type C-type C-type
End-journal profile 端末加工形状 Supported-side 支持側 Fixed-side 固定側 Fixed-side 固定側End-journal profile 端末加工形状 Supported-side 支持側
D-type : Other than the above. 上記以外の形状 D-type : Other than the above. 上記以外の形状
A317 A318
ボー
ルね
じBall Scresw
標準
在庫
品
SRT/SSRTシリ
ーズ
Standard products in stock SRT/SSRT series
ボー
ルね
じBall Scresw
標準
在庫
品
SRT/SSRTシリ
ーズ
Standard products in stock SRT/SSRT series
L4=L5ー41
L5 6.8 +0.1 0
0.8 +0.1 0
φ5.
7 0 -0
.06
φ6
-0.0
02-0
.010
R0.2max
9
L5
L4=L5ー50
φ6-0
.002
-0.0
10
R0.2max9
L5
L4=L5ー50
φ4.
5h6
0 -0.0
08
φ6-0
.001
-0.0
06
30
22.5 7.5
7
φ9.
5h8
0 -0.0
22 M6×0.75
30°×0.5
8 0-0.2
R0.2max
3
L5
7L4 4
L4=L5ー49
L5 6.8 +0.1 0
0.8 +0.1 0
φ5.
7 0 -0
.06
φ6-0
.002
-0.0
10
R0.2max
9
L5
30°×0.5
φ6h
6 0 -0
.008
φ8-0
.002
-0.0
08
φ11
.5h8
0 -0.0
27
37
27 10
9
R0.2max
M8×1.010 0-0.2
4
8L4=L5ー58
φ6
-0.0
02-0
.010
R0.2max9
L5
L4=L 5ー58
L5
L4 4
Unit(単位):mm
Ball Screw Modelボールねじ型番
Travelストローク
Grade精度
Shaft lengthねじ軸長さ
Lead accuracyリード精度 Total
Run-out全振れ
Axialplay
軸方向すきま
PreloadTorque予圧トルク
Nm
Basic Load Rating基本定格荷重 N
L1 L2 L3
Travel deviation代表移動量誤差
ep
Variation変動V300
Dynamic動定格荷重
Ca
Static静定格荷重
Coa
SSRT0802-196R270C7 170 Ct7 196 200 270 ±0.03 ー 0.080~0.020
ー 1950 3100SSRT0802-356R430C7 330 Ct7 356 360 430 ±0.06 0.05 0.120
SSRT0802-196R270C10 170 Ct10 196 200 270 ±0.13 ー 0.160~0.050
SSRT0802-356R430C10 330 Ct10 356 360 430 ±0.24 0.21 0.240
Note )Please refer to page A287 for order code of end-journal machining. 注)追加工の呼び番号指定方法はぺージA287をご参照ください。
Unit(単位):mm
Ball Screw Specifications 諸元
Ball size ボール径 φ1.5875
Number of thread 条数 1
Thread direction 巻方向 Right 右
Shaft root dia. ねじ軸谷径 φ6.6
Number of circuit 循環数 3.7×1
Material材質
Shaft 軸 SUS440C+SUS303
Nut ナット SUS440C
Surface hardnessねじ部表面硬度
HRC55~(Thread area)
Anti-rust treatment防錆処理
Anti-rust oil防錆油
Standard products in stock SSRT series標準在庫品 SSRTシリーズ
SSRT0802
Support-unit Recommendation推奨サポートユニット
Supported-side 支持側 : MSU-6CS/6GSFixed-side 固定側 : MSU-6C/6G
L4:Thread length after end-journal machining. 追加工後のねじ部長さL5:Total length after end-journal machining. 追加工後全長
Shaft dia.(軸径)φ8 Lead(リード)2mm Ct7&Ct10Stainless ステンレス
Unit(単位):mm
Ball Screw Modelボールねじ型番
Travelストローク
Grade精度
Shaft lengthねじ軸長さ
Lead accuracyリード精度 Total
Run-out全振れ
Axialplay
軸方向すきま
PreloadTorque予圧トルク
Nm
Basic Load Rating基本定格荷重 N
L1 L2 L3
Travel deviation代表移動量誤差
ep
Variation変動V300
Dynamic動定格荷重
Ca
Static静定格荷重
Coa
SSRT1002-196R270C7 170 Ct7 196 200 270 ±0.03 ー 0.080~0.020
ー 2200 4000SSRT1002-396R470C7 370 Ct7 396 400 470 ±0.06 0.05 0.120
SSRT1002-196R270C10 170 Ct10 196 200 270 ±0.13 ー 0.160~0.050
SSRT1002-396R470C10 370 Ct10 396 400 470 ±0.27 0.21 0.240
Note )Please refer to page A287 for order code of end-journal machining. 注)追加工の呼び番号指定方法はぺージA287をご参照ください。
Unit(単位):mm
Ball Screw Specifications 諸元
Ball size ボール径 φ1.5875
Number of thread 条数 1
Thread direction 巻方向 Right 右
Shaft root dia. ねじ軸谷径 φ8.6
Number of circuit 循環数 3.7×1
Material材質
Shaft 軸 SUS440C+SUS303
Nut ナット SUS440C
Surface hardnessねじ部表面硬度
HRC55~(Thread area)
Anti-rust treatment防錆処理
Anti-rust oil防錆油
Support-unit Recommendation推奨サポートユニット
Supported-side 支持側 : MSU-8CS/8GSFixed-side 固定側 : MSU-8C/8G
Standard products in stock SSRT series標準在庫品 SSRTシリーズ
SSRT1002
L4:Thread length after end-journal machining. 追加工後のねじ部長さL5:Total length after end-journal machining. 追加工後全長
Shaft dia.(軸径)φ10 Lead(リード)2mm Ct7&Ct10Stainless ステンレス
下表参照see table below
G
G
5
C0.5
70
φ14
.2
22
PCD 29
30°30°
4-φ4.524
(19)
φ20
-0.0
5-0
.10
C0.5
φ37
(φ
7.7)
4
L3
L2
L1
下表参照see table below
G
GC0.5
25
30°
PCD 32
φ40
24
(19) 5
4-φ4.5
30°
φ23
-0.0
5-0
.10
(φ
9.7)
C0.5
70
φ14
.2
4
L3
L2
L1
A-type B-typeA-type B-type C-type C-type
End-journal profile 端末加工形状 Supported-side 支持側 Fixed-side 固定側 Fixed-side 固定側End-journal profile 端末加工形状 Supported-side 支持側
D-type : Other than the above. 上記以外の形状 D-type : Other than the above. 上記以外の形状
A319 A320
ボー
ルね
じBall Scresw
標準
在庫
品
PSR/PSRTシリ
ーズ
Standard products in stock PSR/PSRT series
ボー
ルね
じBall Scresw
標準
在庫
品
PSR/PSRTシリ
ーズ
Standard products in stock PSR/PSRT series
PSR/PSRT シリーズ 精密転造ボールねじ標準在庫品PSR/PSRT series Precision Rolled Ball Screws転造加工したボールねじで、精密級(JIS C5)を実現しました。従来の転造ボールねじでは、精度不足と感じている装置にコストパフォーマンスに優れた製品を提供します。
●特長・ 従来、Ct7、Ct10の並級しかできなかった転造加工で、 精密級(JIS C5)を実現しました。・ 軸端を太く設定したつば付きタイプと全ねじ未加工 タイプの2種類を用意し、お客様に多くの設計の自由度を提供しています。
・ つば付きタイプは、軸端径を太く設定しているため、 カラーの挿入や焼ばめの必要がありません。
・ 固定側軸端の形状、寸法が標準化されており、KSS サポートユニットがそのまま取り付けられる設計になっています。
・ 支持側は、未加工状態となっており、お客様の仕様に 合わせて長さを自由に調節できます。
・ ご要望により、標準以外の軸端形状の対応が可能です。・ 全ねじ未加工タイプは、コストパフォーマンスに優れたタイプで、お客様のご要望に合わせて追加工が可能です。
・ 軸方向すきまは5um以下と最小に設定していますが、ご要望により軸方向すきまを無くす(予圧)ことも可能です。
●Features・ The conventional type of Rolled Ball Screws can
reach the Accuracy grade of Ct10 or Ct7. KSS newly developed the high grade accuracy of Rolled Ball Screw, which can achieve JIS C5 grade.・ We have 2 types of Precision Rolled Ball Screws,
which are Integrated type with larger journal and whole threaded type. So it provides wide variety of design choices.・ For Integrated end-journal type, Fixed side end-
journal can be set larger than nominal diameter of Screw Shaft, so there is no need to use Collar by press fit.・ Fixed side End-journal profile and dimension are
standardized, so KSS Compact Support-Unit can be installed.・ Since supported-side end-journal is unfinished, it
is possible to do additional end machining with your requested thread length.・ Special end-journal profile can be available as
customized order.・ Whole threaded type is a high cost performance
type and end-journal machining is available in accordance with your request.・ The Axial play is set at 5um or less, but Zero
backlash is possible based on your request.
High accuracy(JIS C5) has been achieved by Rolled Ball Screw. We provide Rolled Ball Screws with high precision & better cost performance, which can be replaced with conventional Ground Ball Screw with C5 grade.
【全ねじ未加工/ whole threaded type】【つば付きタイプ/ Integrated journal type】
●ねじ軸呼び外径とリードの組み合わせ Combination of Shaft nominal dia. & Lead
注1)表中の数字:掲載ページを表す Note 1)The numbers in a table :showing a page in this catalogue
Leadリード
Shaft dia.呼び外径
1 2 12
4 A323 A325A324 A326
6 A327 A329A328 A330
8 A331 A333A332 A334
A335 A337A336 A338
A339A340
10 A341A342
12 A343A344
Unit(単位):mm
●材質と表面硬度PSR/PSRTシリーズ(精密転造ボールねじ標準在庫品)の材質と表面硬度は、以下のとおりです。
●精度等級と軸方向すきまPSR/PSRTシリーズ(精密転造ボールねじ標準在庫品)の精度等級は、C5(JIS B 1192-3)となります。また軸方向すきまは0.005mm以下ですが、ご要望により軸方向すきまゼロ(予圧)も承ります。
●Material & Surface hardnessThe material and hardness of PSR/PSRT series (Standardized Precision Rolled Ball Screws) are as follows.
●Accuracy Grade & Axial playThe grade of PSR/PSRT series(Standardized Precision Rolled Ball Screws) is C5(JIS B 1192-3 ).Axial play of this series is 0.005mm or less, but zero backlash(pre-load) type is available by your request.
●種類精密転造ボールねじは、軸端を太く設定したつば付きタイプ(PSRT)と全ねじ未加工タイプ(PSR)の2種類を用意しています。
●VariationWe have 2 types of Precision Rolled Ball Screws, which are Integrated type with larger journal(PSRT) and whole threaded length type(PSR).
●その他PSR/PSRTシリーズ(精密転造ボールねじ標準在庫品)は、標準タイプのナット(リターンプレート式及びエンドキャップ式)に加え、コンパクトタイプのナット(こま式)も用意しています。用途に応じて選択が可能です。
●OthersPSR/PSRT series(Standardized Precision Rolled Ball Screws) provide 3 types of Ball Nut profile. Return-plate style and End-cap style are our standard. In addition Internal-Deflector style as Compact Ball Nut is also in stock. So you can pick one of them based on your design.
●潤滑精密転造ボールねじ全ねじ未加工タイプ(PSRシリーズ)に関しては、在庫状態では、防錆処置のため防錆油を塗布しています。なお防錆油は潤滑機能がありませんので、ご使用に際しては別途潤滑剤を供給してください。 特にご指定のない場合、KSSオリジナルグリース(MSG No.2)を推奨いたします。
●LubricationStandardized Precision Rolled Ball Screws whole threaded length type(PSR Series) will be supplied with anti-rust oil.This oil is not lubricant, when Ball Screw operates, lubricant should be applied.If there is no specific instruction, KSS would recommend our original grease(MSG No.2) as standard lubricant. Please feel free to contact us.
Products製品種別
Material of thread areaボールねじ部材質
Heat treatment熱処理
Surface hardnessボールねじ部の表面硬度
Precision Rolled Ball Screws(PSR series )精密転造ボールねじ(PSRシリーズ)
Shaft / ねじ軸 : S55CInduction hardening高周波焼き入れ HRC58 or more
HRC58以上Nut / ナット : SCM415
Carburizing and Quenching浸炭焼き入れ
Precision Rolled Ball Screwswith Integrated end-journal
(PSRT series )つば付き精密転造ボールねじ
(PSRTシリーズ)
Shaft / ねじ軸 : S55CInduction hardening高周波焼き入れ HRC58 or more
HRC58以上Nut / ナット : SCM415
Carburizing and Quenching浸炭焼き入れ
A321 A322
ボー
ルね
じBall Scresw
標準
在庫
品
PSR/PSRTシリ
ーズ
Standard products in stock PSR/PSRT series
ボー
ルね
じBall Scresw
標準
在庫
品
PSR/PSRTシリ
ーズ
Standard products in stock PSR/PSRT series
●注記1)軸端の詳細寸法は、各ページを参照してください。2)KSSでは、ナットの追加工は行いません。3)仕様は予告なく変更する場合があります。4) 標準の軸端形状(A,B,C)以外の形状をご要望の場合は、
KSSへ問い合わせください。5)お客様で追加工された場合は品質保証は致しかねます。
●Note1)The detail of end-journal dimension for each size
is shown from next page.2)KSS does not make additional Nut machining.3)The specification is subject to change without notice.4)If the other configuration except (A,B,C)is
requested, please contact KSS.5)KSS will not be responsible for quality,
in case re-work is done by other than KSS.
204 C5 B 0 XPSRT 08 01 155 Rー
●呼び番号の構成 Model number notation
①精密転造ボールねじシリーズ記号PSRT : つば付タイプ②ねじ軸呼び外径(mm)③リード(mm)④ナット形式無記号 : 一般K : コンパクトタイプ⑤ねじ部長さ(mm)(追加工後は1mm単位で指定)⑥巻方向(R=右ねじ)⑦ねじ軸全長(mm)(1mm単位で指定)⑧精度等級(JIS C5級)⑨端末加工タイプ図 A-26参照 : A-type,B-type,C-type,
D-type(その他)⑩塗布剤
0 : KSS推奨グリーズ(MSG No.2)1 : 防錆油(Non Ruster PZ2)2 : マルテンプPS23 : その他⑪ナットフランジ向き(図 A-27参照)
①Precision Rolled Ball Screws Series No.PSRT : Integrated journal type②Screw Shaft nominal diameter(mm)③Lead(mm)④Ball Nut type
None : StandardK : Compact type⑤Screw thread length(mm)(Specify in 1mm unit after end-journal machining)⑥Thread direction(R=Right-hand)⑦Screw Shaft total length(mm)(Specify in 1mm unit)⑧Accuracy grade(JIS C5)⑨Shaft end-journal profile
Refer to Fig. A-26 below : A-type,B-type,C-type,D-type(Othes)
⑩Anti-rust oil or Lubricant0 : KSS grease(MSG No.2)1 : Anti-rust oil(Non Ruster PZ2)2 : Multemp PS2 grease3 : Other⑪Nut Flange direction(Refer to Fig. A-27 below)
① ② ③ ⑤ ⑥ ⑦ ⑧ ⑨ ⑩ ⑪
図 A-27 : ナットフランジ向きFig. A-27 : Nut Flange direction
X : Fixed side / 固定側
Y : Supported side / 支持側
図 A-26 : 端末加工タイプ Fig. A-26 : Shaft end-journal profile
A-type : Free / 加工なし
B-type : Journal with snap ring groove / リング溝タイプ
C-type : Journal only / ストレートタイプ
K④
●特殊仕様品以下のような特殊設計品については、受注生産品にて対応いたしますので、KSSまでご照会ください。
1) ねじ軸端の形状、寸法が標準と異なるもの。2) ナットの形状、寸法が標準と異なるもの。3) 軸方向すきまがゼロ(予圧仕様)の製品。4) 標準長さより長い製品。
230 C5PSR 08 01 230 Rー
①精密転造ボールねじシリーズ記号PSR : 全ねじ未加工タイプ
②ねじ軸呼び外径(mm)③リード(mm)④ナット形式無記号 : 一般K : コンパクトタイプ⑤ねじ部長さ(mm)(追加工後は1mm単位で指定)⑥巻方向(R=右ねじ)⑦ねじ軸全長(mm)(1mm単位で指定)⑧精度等級(JIS C5級)
①Precision Rolled Ball Screws Series No.PSR : Whole threaded type
②Screw Shaft nominal diameter(mm)③Lead(mm)④Ball Nut type
None : StandardK : Compact type⑤Screw thread length(mm)(Specify in 1mm unit after end-journal machining)⑥Thread direction(R=Right-hand)⑦Screw Shaft total length(mm)(Specify in 1mm unit)⑧Accuracy grade(Class JIS C5)
① ② ③ ⑤ ⑥ ⑦ ⑧
【つば付きタイプ/ Integrated journal type】つば付きタイプ(PSRT)の追加工をご要望の場合は、以下の呼び番号で、長さ、軸端形状、潤滑剤、ナット向きをご指示ください。In case of PSRT type(Integrated journal type), please designate length, end-journal profile, lubricant and Nut direction according to the Model number notation below.
D-type : Other than the above / 上記以外の形状
【全ねじ未加工タイプ/ Whole threaded type】
K④
●Customized DesignIt will be the customized if you need special specifications like below, please ask KSS representative.
1)Non‐standard profile or dimension on Shaft end‐journal.
2)Non‐standard profile or dimension on Ball Nut or Flange.
3)Zero backlash (Pre‐loaded) type Ball Screw.4)Longer length of Ball Screw Shaft than
standard product.
全ねじ未加工タイプ(PSRタイプ)の呼び番号の構成は以下のとおりです。軸端の追加工は、図面とともにご指示ください。Model number notation of PSR type(whole threaded type) is as follows. Please designate end-journal profile with your simple sketch.
●注記1)ご要望により軸方向すきまを無くす(予圧)こともできますので、KSSまでご照会ください。
2)軸端の追加工はKSSで行うことをお奨めします。KSS以外で追加工を行う場合は、追加工後の精度保証はいたしかねますので、ご了承ください。
3)追加工については、追加工指示図(ポンチ絵)とともに、ご指示くださるようお願いいたします。
4)ナットの追加工は、行っておりませんので、フランジ形状等は、標準形状に合わせて設計するようにしてください。
5)ボールねじを使用する上で、潤滑剤の供給は必ず行ってください。防錆油は潤滑剤ではありませんので、ご注意ください。
●Note1)Zero backlash is possible by your request,
please ask KSS representative.2)We recommend additional end-journal
machining is done by KSS. We do not guarantee accuracy after re-works done by other than KSS.
3)Please send us drawing with end-journal profile when you request end-journal maching.
4)Additional machining is not applied to the Nut.Please design flange configuration according to our standard dimension.
5)In Ball Screws use, lubricant should be applied on them. Please note that anti-rust oil is not lubricant.
A323 A324
ボー
ルね
じBall Scresw
標準
在庫
品
PSR/PSRTシリ
ーズ
Standard products in stock PSR/PSRT series
ボー
ルね
じBall Scresw
標準
在庫
品
PSR/PSRTシリ
ーズ
Standard products in stock PSR/PSRT series
Unit(単位):mm
Ball Screw Specifications 諸元
Ball size ボール径 φ0.8
Number of thread 条数 1
Thread direction 巻方向 Right 右
Shaft root dia. ねじ軸谷径 φ3.3
Number of circuit 循環数 3.7×1
Material材質
Shaft 軸 S55C+SUS303
Nut ナット SCM415H
Surface hardnessねじ部表面硬度
HRC58~(Thread area)
Lubrication出荷時封入剤
KSS Original Grease MSG No.2
see table below
4
6.5
5(18)
(6)
23
0.005
PCD 17
30°
15
30°
4-φ3.4
R0.2max
0.012
(φ
3.85)
17
4(13)
φ6h
8 0 -0.
018
C0.3
C0.3
φ3h
6
M4x0.530°x0.3
C0.5
2.5
φ23
φ4-
0.00
1-
0.00
6
5 0-0.2
-0.
006
0
0.010
0.005
E
A
E
G
下表参照
A
0.010
L3
L2
L1
L4
A
G
φ11
0.0
5-
0.10
G
E
Standard products in stock PSRT series標準在庫品 PSRTシリーズ
PSRT0401 Shaft dia.(軸径)φ4 Lead(リード)1mm C5
Unit(単位):mm
Ball Screw Modelボールねじ型番
Travelストローク
Shaft lengthねじ軸長さ Travel deviation
代表移動量誤差ep
Total Run-out全振れ
Axial play軸方向すきま
Basic Load Rating基本定格荷重 N
L1 L2 L3 L4
Dynamic動定格荷重
Ca
Static静定格荷重
Coa
PSRT0401-72R105C5 50 72 76 82 105 ±0.018 0.035 ~0.005 560 790
Note) Please refer to page A321 for order code of end-journal machining. 注)追加工の呼び番号指定方法は、ページA321をご参照ください。
Supported-side end-journal profile 支持側端末加工形状
A04-φ04journal
A-type B-type C-type
R0.15max
7
R0.15max
L6
L6
L6
7
φ3-
0.00
2-
0.01
0
φ2.
7±
0.03
4.35±0.05
0.5+0.1 0
φ3-
0.00
2-
0.01
0
L5=L6-33
L5=L6-40
L5=L6-40
A-type
Support-unit Recommendation推奨サポートユニット
Supported-side 支持側 : MSU-4CS/4GSFixed-side 固定側 : MSU-4C/4G
L5:Thread length after end-journal machining. 追加工後のねじ部長さL6:Total length after end-journal machining. 追加工後全長
B-type C-type
D-type : Other than the above. 上記以外の形状
Unit(単位):mm
Ball Screw Specifications 諸元
Ball size ボール径 φ0.8
Number of thread 条数 1
Thread direction 巻方向 Right 右
Shaft root dia. ねじ軸谷径 φ3.3
Number of circuit 循環数 3.7×1
Material材質
Shaft 軸 S55C
Nut ナット SCM415H
Surface hardnessねじ部表面硬度
HRC58~(Thread area)
Anti-rust treatment防錆処理
Anti-rust oil防錆油
see table below(13)4
C0.5
17
φ11-
0.05
-0.
10
4-φ3.4
30°
15
30°
(φ
3.85)
PCD 17
φ23
L1
下表参照 E-F
FE
Standard products in stock PSR series標準在庫品 PSRシリーズ
PSR0401 Shaft dia.(軸径)φ4 Lead(リード)1mm C5
Unit(単位):mm
Ball Screw Modelボールねじ型番
Travelストローク
Shaft lengthねじ軸長さ Travel deviation
代表移動量誤差ep
Total Run-out全振れ
Axial play軸方向すきま
Basic Load Rating基本定格荷重 N
L1
Dynamic動定格荷重
Ca
Static静定格荷重
Coa
PSR0401-100R100C5 75 100 ±0.018 0.035 ~0.005 560 790
Note) Please dsignate end-journal profile with your sketch. 注)軸端の追加工は図面とともにご指示ください。
A325 A326
ボー
ルね
じBall Scresw
標準
在庫
品
PSR/PSRTシリ
ーズ
Standard products in stock PSR/PSRT series
ボー
ルね
じBall Scresw
標準
在庫
品
PSR/PSRTシリ
ーズ
Standard products in stock PSR/PSRT series
Unit(単位):mm
Ball Screw Specifications 諸元
Ball size ボール径 φ0.6
Number of thread 条数 1
Thread direction 巻方向 Right 右
Shaft root dia. ねじ軸谷径 φ3.4
Number of circuit 循環数 1×3
Material材質
Shaft 軸 S55C+SUS303
Nut ナット SCM415H
Surface hardnessねじ部表面硬度
HRC58~(Thread area)
Lubrication出荷時封入剤
KSS Original Grease MSG No.2
see table below
4
6.5
5(18)
(6)
23
0.005
PCD 14
30°
13
30°
4-φ2.9
R0.2max
0.012
(φ
3.95)
13
3(10)
φ6h
8 0 -0.
018
C0.3
C0.3 φ3h
6
M4x0.530°x0.3
C0.5
2.5
φ19
φ4-
0.00
1-
0.00
6
5 0-0.2
-0.
006
0
0.010
0.005
E
A
E
G
下表参照
A
0.010
L3
L2
L1
L4
A
G
φ9 -
0.05
-0.
10
G
E
Standard products in stock PSRT series標準在庫品 PSRTシリーズ
PSRT0401K Shaft dia.(軸径)φ4 Lead(リード)1mm C5
Unit(単位):mm
Ball Screw Modelボールねじ型番
Travelストローク
Shaft lengthねじ軸長さ Travel deviation
代表移動量誤差ep
Total Run-out全振れ
Axial play軸方向すきま
Basic Load Rating基本定格荷重 N
L1 L2 L3 L4
Dynamic動定格荷重
Ca
Static静定格荷重
Coa
PSRT0401K-72R105C5 50 72 76 82 105 ±0.018 0.035 ~0.005 300 430
Note) Please refer to page A321 for order code of end-journal machining. 注)追加工の呼び番号指定方法は、ページA321をご参照ください。
Supported-side end-journal profile 支持側端末加工形状
Compact Nut / コンパクトナット
A04-φ04journal
A-type B-type C-type
R0.15max
7
R0.15max
L6
L6
L6
7
φ3-
0.00
2-
0.01
0
φ2.
7±
0.03
4.35±0.05
0.5+0.1 0
φ3-
0.00
2-
0.01
0
L5=L6-33
L5=L6-40
L5=L6-40
A-type
Support-unit Recommendation推奨サポートユニット
Supported-side 支持側 : MSU-4CS/4GSFixed-side 固定側 : MSU-4C/4G
L5:Thread length after end-journal machining. 追加工後のねじ部長さL6:Total length after end-journal machining. 追加工後全長
B-type C-type
D-type : Other than the above. 上記以外の形状
Unit(単位):mm
Ball Screw Specifications 諸元
Ball size ボール径 φ0.6
Number of thread 条数 1
Thread direction 巻方向 Right 右
Shaft root dia. ねじ軸谷径 φ3.4
Number of circuit 循環数 1×3
Material材質
Shaft 軸 S55C
Nut ナット SCM415H
Surface hardnessねじ部表面硬度
HRC58~(Thread area)
Anti-rust treatment防錆処理
Anti-rust oil防錆油
(10)3
C0.5
13
φ9-
0.05
-0.
10
4-φ2.9
30°
13
30°
(φ
3.95)
PCD 14
φ19
L1
FE
E-F下表参照see table below
Standard products in stock PSR series標準在庫品 PSRシリーズ
PSR0401K Shaft dia.(軸径)φ4 Lead(リード)1mm C5Compact Nut / コンパクトナット
Unit(単位):mm
Ball Screw Modelボールねじ型番
Travelストローク
Shaft lengthねじ軸長さ Travel deviation
代表移動量誤差ep
Total Run-out全振れ
Axial play軸方向すきま
Basic Load Rating基本定格荷重 N
L1
Dynamic動定格荷重
Ca
Static静定格荷重
Coa
PSR0401K-100R100C5 80 100 ±0.018 0.035 ~0.005 300 430
Note) Please dsignate end-journal profile with your sketch. 注)軸端の追加工は図面とともにご指示ください。
A327 A328
ボー
ルね
じBall Scresw
標準
在庫
品
PSR/PSRTシリ
ーズ
Standard products in stock PSR/PSRT series
ボー
ルね
じBall Scresw
標準
在庫
品
PSR/PSRTシリ
ーズ
Standard products in stock PSR/PSRT series
Unit(単位):mm
Ball Screw Specifications 諸元
Ball size ボール径 φ0.8
Number of thread 条数 1
Thread direction 巻方向 Right 右
Shaft root dia. ねじ軸谷径 φ5.3
Number of circuit 循環数 3.7×1
Material材質
Shaft 軸 S55C+SUS303
Nut ナット SCM415H
Surface hardnessねじ部表面硬度
HRC58~(Thread area)
Lubrication出荷時封入剤
KSS Original Grease MSG No.2
64
(25)
R0.2max
6.5
(19)
(7)
16
30°
4-φ3.4
30°
PCD 20
φ4h
6 0 -0.
008
7 0-0.2
M5x0.5
C0.3
C0.3φ5-
0.00
1-
0.00
6
3
30°x0.3
φ8h
8 0 -0.
022
φ26
17
4(13)
φ13-
0.05
-0.
10
(φ
5.85)
C0.5
0.010 A
E
0.005
0.010
A0.012
G
下表参照 G
0.005 E
E
see table below
A
G
L3
L2
L1
L4
Standard products in stock PSRT series標準在庫品 PSRTシリーズ
PSRT0601 Shaft dia.(軸径)φ6 Lead(リード)1mm C5
Unit(単位):mm
Ball Screw Specifications 諸元
Ball size ボール径 φ0.8
Number of thread 条数 1
Thread direction 巻方向 Right 右
Shaft root dia. ねじ軸谷径 φ5.3
Number of circuit 循環数 3.7×1
Material材質
Shaft 軸 S55C
Nut ナット SCM415H
Surface hardnessねじ部表面硬度
HRC58~(Thread area)
Anti-rust treatment防錆処理
Anti-rust oil防錆油
see table below
(13)4
C0.5
φ13-
0.05
-0.
10
PCD 20
16
30°
17
φ26
(φ
5.85)
4-φ3.4
30°
L1
F
E-F下表参照
E
Standard products in stock PSR series標準在庫品 PSRシリーズ
PSR0601 Shaft dia.(軸径)φ6 Lead(リード)1mm C5
Unit(単位):mm
Ball Screw Modelボールねじ型番
Travelストローク
Shaft lengthねじ軸長さ Travel deviation
代表移動量誤差ep
Total Run-out全振れ
Axial play軸方向すきま
Basic Load Rating基本定格荷重 N
L1
Dynamic動定格荷重
Ca
Static静定格荷重
Coa
PSR0601-200R200C5 175 200 ±0.020 0.050 ~0.005 680 1200
Note) Please dsignate end-journal profile with your sketch. 注)軸端の追加工は図面とともにご指示ください。
Unit(単位):mm
Ball Screw Modelボールねじ型番
Travelストローク
Shaft lengthねじ軸長さ Travel deviation
代表移動量誤差ep
Total Run-out全振れ
Axial play軸方向すきま
Basic Load Rating基本定格荷重 N
L1 L2 L3 L4
Dynamic動定格荷重
Ca
Static静定格荷重
Coa
PSRT0601-89R125C5 65 89 93 100 125 ±0.018 0.035 ~0.005 680 1200
Note) Please refer to page A321 for order code of end-journal machining. 注)追加工の呼び番号指定方法は、ページA321をご参照ください。
Supported-side end-journal profile 支持側端末加工形状
Support-unit Recommendation推奨サポートユニット
Supported-side 支持側 : MSU-5CS/5GSFixed-side 固定側 : MSU-5C/5G
L5:Thread length after end-journal machining. 追加工後のねじ部長さL6:Total length after end-journal machining. 追加工後全長
A04-φ06journal
A-type B-type C-type
R0.2max
8
R0.2max
L6
L6
L6
8
φ4-
0.00
2-
0.01
0
φ3.
7±
0.03
φ4-
0.00
2-
0.01
0
5.35 ±0.05
0.5+0.1 0
L5=L6-36
L5=L6-44
L5=L6-44
A-type B-type C-type
D-type : Other than the above. 上記以外の形状
A329 A330
ボー
ルね
じBall Scresw
標準
在庫
品
PSR/PSRTシリ
ーズ
Standard products in stock PSR/PSRT series
ボー
ルね
じBall Scresw
標準
在庫
品
PSR/PSRTシリ
ーズ
Standard products in stock PSR/PSRT series
Unit(単位):mm
Ball Screw Specifications 諸元
Ball size ボール径 φ0.8
Number of thread 条数 1
Thread direction 巻方向 Right 右
Shaft root dia. ねじ軸谷径 φ5.3
Number of circuit 循環数 1×3
Material材質
Shaft 軸 S55C
Nut ナット SCM415H
Surface hardnessねじ部表面硬度
HRC58~(Thread area)
Anti-rust treatment防錆処理
Anti-rust oil防錆油
see table below
(11)3.5
C0.5
φ11-
0.05
-0.
10
PCD 17
15
30°
14.5
φ23
(φ
5.9)
4-φ3.4
30°
L1
F
E-F下表参照
E
Standard products in stock PSR series標準在庫品 PSRシリーズ
PSR0601K Shaft dia.(軸径)φ6 Lead(リード)1mm C5
Unit(単位):mm
Ball Screw Specifications 諸元
Ball size ボール径 φ0.8
Number of thread 条数 1
Thread direction 巻方向 Right 右
Shaft root dia. ねじ軸谷径 φ5.3
Number of circuit 循環数 1×3
Material材質
Shaft 軸 S55C+SUS303
Nut ナット SCM415H
Surface hardnessねじ部表面硬度
HRC58~(Thread area)
Lubrication出荷時封入剤
KSS Original Grease MSG No.2
64
(25)
R0.2max
6.5
(19)
(7)
15
30°
4-φ3.4
30°
PCD 17
φ4h
6 0 -0.
008
7 0-0.2
M5x0.5
C0.3
C0.3φ5-
0.00
1-
0.00
6
3
30°x0.3
φ8h
8 0 -0.
022
φ23
14.5
3.5(11)
φ11-
0.05
-0.
10
(φ
5.9)
C0.5
0.010 A
E
0.005
0.010
A0.012
G
下表参照 G
0.005 E
E
see table below
A
G
L3
L2
L1
L4
Standard products in stock PSRT series標準在庫品 PSRTシリーズ
PSRT0601K Shaft dia.(軸径)φ6 Lead(リード)1mm C5Compact Nut / コンパクトナット
Unit(単位):mm
Ball Screw Modelボールねじ型番
Travelストローク
Shaft lengthねじ軸長さ Travel deviation
代表移動量誤差ep
Total Run-out全振れ
Axial play軸方向すきま
Basic Load Rating基本定格荷重 N
L1
Dynamic動定格荷重
Ca
Static静定格荷重
Coa
PSR0601K-200R2000C5 180 200 ±0.020 0.050 ~0.005 560 950
Note) Please dsignate end-journal profile with your sketch. 注)軸端の追加工は図面とともにご指示ください。
Unit(単位):mm
Ball Screw Modelボールねじ型番
Travelストローク
Shaft lengthねじ軸長さ Travel deviation
代表移動量誤差ep
Total Run-out全振れ
Axial play軸方向すきま
Basic Load Rating基本定格荷重 N
L1 L2 L3 L4
Dynamic動定格荷重
Ca
Static静定格荷重
Coa
PSRT0601K-89R125C5 65 89 93 100 125 ±0.018 0.035 ~0.005 560 950
Note) Please refer to page A321 for order code of end-journal machining. 注)追加工の呼び番号指定方法は、ページA321をご参照ください。
Supported-side end-journal profile 支持側端末加工形状
Compact Nut / コンパクトナット
Support-unit Recommendation推奨サポートユニット
Supported-side 支持側 : MSU-5CS/5GSFixed-side 固定側 : MSU-5C/5G
L5:Thread length after end-journal machining. 追加工後のねじ部長さL6:Total length after end-journal machining. 追加工後全長
A04-φ06journal
A-type B-type C-type
R0.2max
8
R0.2max
L6
L6
L6
8
φ4-
0.00
2-
0.01
0
φ3.
7±
0.03
φ4-
0.00
2-
0.01
0
5.35 ±0.05
0.5+0.1 0
L5=L6-36
L5=L6-44
L5=L6-44
A-type B-type C-type
D-type : Other than the above. 上記以外の形状
A331 A332
ボー
ルね
じBall Scresw
標準
在庫
品
PSR/PSRTシリ
ーズ
Standard products in stock PSR/PSRT series
ボー
ルね
じBall Scresw
標準
在庫
品
PSR/PSRTシリ
ーズ
Standard products in stock PSR/PSRT series
Unit(単位):mm
Ball Screw Specifications 諸元
Ball size ボール径 φ0.8
Number of thread 条数 1
Thread direction 巻方向 Right 右
Shaft root dia. ねじ軸谷径 φ7.3
Number of circuit 循環数 3.7×1
Material材質
Shaft 軸 S55C
Nut ナット SCM415H
Surface hardnessねじ部表面硬度
HRC58~(Thread area)
Anti-rust treatment防錆処理
Anti-rust oil防錆油
下表参照see table below
L1
17
(13)4
C0.5
φ16
-0.0
5-0
.10
18
(φ
7.85)
PCD 23
φ29
30°
4-φ3.4
30°
F
E-F
E
Standard products in stock PSR series標準在庫品 PSRシリーズ
PSR0801 Shaft dia.(軸径)φ8 Lead(リード)1mm C5
Unit(単位):mm
Ball Screw Specifications 諸元
Ball size ボール径 φ0.8
Number of thread 条数 1
Thread direction 巻方向 Right 右
Shaft root dia. ねじ軸谷径 φ7.3
Number of circuit 循環数 3.7×1
Material材質
Shaft 軸 S55C+SUS303
Nut ナット SCM415H
Surface hardnessねじ部表面硬度
HRC58~(Thread area)
Lubrication出荷時封入剤
KSS Original Grease MSG No.2
G
E
E0.005G
0.012 A
0.010
φ6-
0.00
2-
0.00
7
30°x0.5A
see table below下表参照
(φ
7.85)
G
0.010
0.005
L3
17
(13) 4
C0.5
φ16-
0.05
-0.
10
30°
18
PCD 23φ29
4-φ3.4
30°
L2
4L1
φ4.
5h6
0 -0.
008
30
(7)
(22.5) 7.5
7
C0.3
C0.5
M6x0.75
8 0-0.2
L4
R0.2max
3
φ9.
5h8
0 -0.
022
A
E
Standard products in stock PSRT series標準在庫品 PSRTシリーズ
PSRT0801 Shaft dia.(軸径)φ8 Lead(リード)1mm C5
Unit(単位):mm
Ball Screw Modelボールねじ型番
Travelストローク
Shaft lengthねじ軸長さ Travel deviation
代表移動量誤差ep
Total Run-out全振れ
Axial play軸方向すきま
Basic Load Rating基本定格荷重 N
L1
Dynamic動定格荷重
Ca
Static静定格荷重
Coa
PSR0801-230R230C5 205 230 ±0.023 0.065 ~0.005 780 1650
Note) Please dsignate end-journal profile with your sketch. 注)軸端の追加工は図面とともにご指示ください。
Support-unit Recommendation推奨サポートユニット
Supported-side 支持側 : MSU-6CS/6GSFixed-side 固定側 : MSU-6C/6G
L5:Thread length after end-journal machining. 追加工後のねじ部長さL6:Total length after end-journal machining. 追加工後全長
Supported-side end-journal profile 支持側端末加工形状
Unit(単位):mm
Ball Screw Modelボールねじ型番
Travelストローク
Shaft lengthねじ軸長さ Travel deviation
代表移動量誤差ep
Total Run-out全振れ
Axial play軸方向すきま
Basic Load Rating基本定格荷重 N
L1 L2 L3 L4
Dynamic動定格荷重
Ca
Static静定格荷重
Coa
PSRT0801-169R210C5 145 169 173 180 210 ±0.020 0.065 ~0.005 780 1650
Note) Please refer to page A321 for order code of end-journal machining. 注)追加工の呼び番号指定方法は、ページA321をご参照ください。
A04-φ08journal
A-type B-type C-type
6.8 +0.1 0
0.8 +0.1 0
φ5.
7 0 -0
.06
φ6
-0.0
02-0
.010
R0.2max
9
L6
L6
L5=L6-41
L5=L6-50
L5=L6-50
φ6
-0.0
02-0
.010
R0.2max 9
L6
A-type B-type C-type
D-type : Other than the above 上記以外の形状
A333 A334
ボー
ルね
じBall Scresw
標準
在庫
品
PSR/PSRTシリ
ーズ
Standard products in stock PSR/PSRT series
ボー
ルね
じBall Scresw
標準
在庫
品
PSR/PSRTシリ
ーズ
Standard products in stock PSR/PSRT series
Unit(単位):mm
Ball Screw Specifications 諸元
Ball size ボール径 φ0.8
Number of thread 条数 1
Thread direction 巻方向 Right 右
Shaft root dia. ねじ軸谷径 φ7.3
Number of circuit 循環数 1×3
Material材質
Shaft 軸 S55C
Nut ナット SCM415H
Surface hardnessねじ部表面硬度
HRC58~(Thread area)
Anti-rust treatment防錆処理
Anti-rust oil防錆油
E
see table below
L1
15
(11)4
C0.5
φ13-
0.05
-0.
10
17
(φ
7.9)
PCD 20
φ26
30°
4-φ3.4
30°E-F下表参照
F
Standard products in stock PSR series標準在庫品 PSRシリーズ
PSR0801K Shaft dia.(軸径)φ8 Lead(リード)1mm C5
Unit(単位):mm
Ball Screw Specifications 諸元
Ball size ボール径 φ0.8
Number of thread 条数 1
Thread direction 巻方向 Right 右
Shaft root dia. ねじ軸谷径 φ7.3
Number of circuit 循環数 1×3
Material材質
Shaft 軸 S55C+SUS303
Nut ナット SCM415H
Surface hardnessねじ部表面硬度
HRC58~(Thread area)
Lubrication出荷時封入剤
KSS Original Grease MSG No.2
G
E
E0.005G
0.012 A
0.010
φ6-
0.00
2-
0.00
7
30°x0.5A
see table below下表参照
(φ
7.9)
G
0.010
0.005
L3
15
(11) 4
C0.5
φ13-
0.05
-0.
10
30°
17
PCD 20
φ26
4-φ3.4
30°
L2
4L1
φ4.
5h6
0 -0.
008
30
(7)
(22.5) 7.5
7
C0.3
C0.3
M6x0.75
8 0-0.2
L4
R0.2max
3
φ9.
5h8
0 -0.
022
A
E
Standard products in stock PSRT series標準在庫品 PSRTシリーズ
PSRT0801K Shaft dia.(軸径)φ8 Lead(リード)1mm C5Compact Nut / コンパクトナット
Unit(単位):mm
Ball Screw Modelボールねじ型番
Travelストローク
Shaft lengthねじ軸長さ Travel deviation
代表移動量誤差ep
Total Run-out全振れ
Axial play軸方向すきま
Basic Load Rating基本定格荷重 N
L1
Dynamic動定格荷重
Ca
Static静定格荷重
Coa
PSR0801K-230R230C5 210 230 ±0.023 0.065 ~0.005 650 1300
Note) Please dsignate end-journal profile with your sketch. 注)軸端の追加工は図面とともにご指示ください。
Unit(単位):mm
Ball Screw Modelボールねじ型番
Travelストローク
Shaft lengthねじ軸長さ Travel deviation
代表移動量誤差ep
Total Run-out全振れ
Axial play軸方向すきま
Basic Load Rating基本定格荷重 N
L1 L2 L3 L4
Dynamic動定格荷重
Ca
Static静定格荷重
Coa
PSRT0801K-169R210C5 145 169 173 180 210 ±0.020 0.065 ~0.005 650 1300
Note) Please refer to page A321 for order code of end-journal machining. 注)追加工の呼び番号指定方法は、ページA321をご参照ください。
Supported-side end-journal profile 支持側端末加工形状
Compact Nut / コンパクトナット
Support-unit Recommendation推奨サポートユニット
Supported-side 支持側 : MSU-6CS/6GSFixed-side 固定側 : MSU-6C/6G
L5:Thread length after end-journal machining. 追加工後のねじ部長さL6:Total length after end-journal machining. 追加工後全長
A04-φ08journal
A-type B-type C-type
6.8 +0.1 0
0.8 +0.1 0
φ5.
7 0 -0
.06
φ6
-0.0
02-0
.010
R0.2max
9
L6
L6
L5=L6-41
L5=L6-50
L5=L6-50
φ6
-0.0
02-0
.010
R0.2max 9
L6
A-type B-type C-type
D-type : Other than the above 上記以外の形状
A335 A336
ボー
ルね
じBall Scresw
標準
在庫
品
PSR/PSRTシリ
ーズ
Standard products in stock PSR/PSRT series
ボー
ルね
じBall Scresw
標準
在庫
品
PSR/PSRTシリ
ーズ
Standard products in stock PSR/PSRT series
Unit(単位):mm
Ball Screw Specifications 諸元
Ball size ボール径 φ1.5875
Number of thread 条数 1
Thread direction 巻方向 Right 右
Shaft root dia. ねじ軸谷径 φ6.6
Number of circuit 循環数 3.7×1
Material材質
Shaft 軸 S55C
Nut ナット SCM415H
Surface hardnessねじ部表面硬度
HRC58~(Thread area)
Anti-rust treatment防錆処理
Anti-rust oil防錆油
下表参照see table below
L1
φ20
-0.0
5-0
.10
C0.5
24
(19)5
22
PCD 29
30°
4-φ4.5
30°
(φ
7.7)
φ37
F
E-F
E
Standard products in stock PSR series標準在庫品 PSRシリーズ
PSR0802 Shaft dia.(軸径)φ8 Lead(リード)2mm C5
Unit(単位):mm
Ball Screw Specifications 諸元
Ball size ボール径 φ1.5875
Number of thread 条数 1
Thread direction 巻方向 Right 右
Shaft root dia. ねじ軸谷径 φ6.6
Number of circuit 循環数 3.7×1
Material材質
Shaft 軸 S55C+SUS303
Nut ナット SCM415H
Surface hardnessねじ部表面硬度
HRC58~(Thread area)
Lubrication出荷時封入剤
KSS Original Grease MSG No.2
φ4.
5h6
0 -0.
008
PCD 29
30°30°
4-φ4.5
0.005
0.010
(22.5) 7.5
7
C0.3
C0.5
M6x0.75
R0.2max
φ6-
0.00
2-
0.00
730°x0.5
8 0-0.2
3
下表参照 G
G
0.012 A
see table below
A
φ9.
5h8
0 -0.
022
5
24
(19)
φ20-
0.05
-0.
10
C0.5
∅37
(φ
7.7)
0.005L2
4L1
(7)
L4
30L3
E
E
A
E
22
G0.010
Standard products in stock PSRT series標準在庫品 PSRTシリーズ
PSRT0802 Shaft dia.(軸径)φ8 Lead(リード)2mm C5
Support-unit Recommendation推奨サポートユニット
Supported-side 支持側 : MSU-6CS/6GSFixed-side 固定側 : MSU-6C/6G
L5:Thread length after end-journal machining. 追加工後のねじ部長さL6:Total length after end-journal machining. 追加工後全長
Supported-side end-journal profile 支持側端末加工形状
A04-φ08journal
A-type B-type C-type
6.8 +0.1 0
0.8 +0.1 0
φ5.
7 0 -0
.06
φ6
-0.0
02-0
.010
R0.2max
9
L6
L6
L5=L6-41
L5=L6-50
L5=L6-50
φ6
-0.0
02-0
.010
R0.2max 9
L6
B-type C-type
D-type : Other than the above 上記以外の形状Unit(単位):mm
Ball Screw Modelボールねじ型番
Travelストローク
Shaft lengthねじ軸長さ Travel deviation
代表移動量誤差ep
Total Run-out全振れ
Axial play軸方向すきま
Basic Load Rating基本定格荷重 N
L1 L2 L3 L4
Dynamic動定格荷重
Ca
Static静定格荷重
Coa
PSRT0802-169R210C5 140 169 173 180 210 ±0.020 0.065 ~0.005 2400 4100
Note) Please refer to page A321 for order code of end-journal machining. 注)追加工の呼び番号指定方法は、ページA321をご参照ください。
Unit(単位):mm
Ball Screw Modelボールねじ型番
Travelストローク
Shaft lengthねじ軸長さ Travel deviation
代表移動量誤差ep
Total Run-out全振れ
Axial play軸方向すきま
Basic Load Rating基本定格荷重 N
L1
Dynamic動定格荷重
Ca
Static静定格荷重
Coa
PSR0802-230R230C5 200 230 ±0.023 0.065 ~0.005 2400 4100
Note) Please dsignate end-journal profile with your sketch. 注)軸端の追加工は図面とともにご指示ください。
A-type
A337 A338
ボー
ルね
じBall Scresw
標準
在庫
品
PSR/PSRTシリ
ーズ
Standard products in stock PSR/PSRT series
ボー
ルね
じBall Scresw
標準
在庫
品
PSR/PSRTシリ
ーズ
Standard products in stock PSR/PSRT series
Unit(単位):mm
Ball Screw Specifications 諸元
Ball size ボール径 φ1.2
Number of thread 条数 1
Thread direction 巻方向 Right 右
Shaft root dia. ねじ軸谷径 φ7.0
Number of circuit 循環数 1×3
Material材質
Shaft 軸 S55C
Nut ナット SCM415H
Surface hardnessねじ部表面硬度
HRC58~(Thread area)
Anti-rust treatment防錆処理
Anti-rust oil防錆油
see table below
L1
φ15-
0.05
-0.
10
C0.5
18
(14)4
19
PCD 22
30°
4-φ3.4
30°
(φ
7.9)
φ28
F
E-F下表参照
E
Standard products in stock PSR series標準在庫品 PSRシリーズ
PSR0802K Shaft dia.(軸径)φ8 Lead(リード)2mm C5
Unit(単位):mm
Ball Screw Specifications 諸元
Ball size ボール径 φ1.2
Number of thread 条数 1
Thread direction 巻方向 Right 右
Shaft root dia. ねじ軸谷径 φ7.0
Number of circuit 循環数 1×3
Material材質
Shaft 軸 S55C+SUS303
Nut ナット SCM415H
Surface hardnessねじ部表面硬度
HRC58~(Thread area)
Lubrication出荷時封入剤
KSS Original Grease MSG No.2
φ4.
5h6
0 -0.
008
PCD 22
30°30°
4-φ3.4
0.005
0.010
(22.5) 7.5
7
C0.3
C0.3
M6x0.75
R0.2max
φ6-
0.00
2-
0.00
730°x0.5
8 0-0.2
3
下表参照 G
G
0.012 A
see table below
A
φ9.
5h8
0 -0.
022
4
18
(14)
φ15-
0.05
-0.
10
C0.5
∅28
(φ
7.9)
0.005L2
4L1
(7)
L4
30L3
E
E
A
E
19
G0.010
Standard products in stock PSRT series標準在庫品 PSRTシリーズ
PSRT0802K Shaft dia.(軸径)φ8 Lead(リード)2mm C5
Unit(単位):mm
Ball Screw Modelボールねじ型番
Travelストローク
Shaft lengthねじ軸長さ Travel deviation
代表移動量誤差ep
Total Run-out全振れ
Axial play軸方向すきま
Basic Load Rating基本定格荷重 N
L1
Dynamic動定格荷重
Ca
Static静定格荷重
Coa
PSR0802K-230R230C5 205 230 ±0.023 0.065 ~0.005 1300 2300
Note) Please dsignate end-journal profile with your sketch. 注)軸端の追加工は図面とともにご指示ください。
Unit(単位):mm
Ball Screw Modelボールねじ型番
Travelストローク
Shaft lengthねじ軸長さ Travel deviation
代表移動量誤差ep
Total Run-out全振れ
Axial play軸方向すきま
Basic Load Rating基本定格荷重 N
L1 L2 L3 L4
Dynamic動定格荷重
Ca
Static静定格荷重
Coa
PSRT0802K-169R210C5 145 169 173 180 210 ±0.020 0.065 ~0.005 1300 2300
Note) Please refer to page A321 for order code of end-journal machining. 注)追加工の呼び番号指定方法は、ページA321をご参照ください。
Supported-side end-journal profile 支持側端末加工形状
Compact Nut / コンパクトナット Compact Nut / コンパクトナット
Support-unit Recommendation推奨サポートユニット
Supported-side 支持側 : MSU-6CS/6GSFixed-side 固定側 : MSU-6C/6G
L5:Thread length after end-journal machining. 追加工後のねじ部長さL6:Total length after end-journal machining. 追加工後全長
A04-φ08journal
A-type B-type C-type
6.8 +0.1 0
0.8 +0.1 0
φ5.
7 0 -0
.06
φ6
-0.0
02-0
.010
R0.2max
9
L6
L6
L5=L6-41
L5=L6-50
L5=L6-50
φ6
-0.0
02-0
.010
R0.2max 9
L6
D-type : Other than the above 上記以外の形状
B-type C-typeA-type
A339 A340
ボー
ルね
じBall Scresw
標準
在庫
品
PSR/PSRTシリ
ーズ
Standard products in stock PSR/PSRT series
ボー
ルね
じBall Scresw
標準
在庫
品
PSR/PSRTシリ
ーズ
Standard products in stock PSR/PSRT series
Unit(単位):mm
Ball Screw Specifications 諸元
Ball size ボール径 φ1.5875
Number of thread 条数 2
Thread direction 巻方向 Right 右
Shaft root dia. ねじ軸谷径 φ6.7
Number of circuit 循環数 1.6×2
Material材質
Shaft 軸 S55C
Nut ナット SCM415H
Surface hardnessねじ部表面硬度
HRC58~(Thread area)
Anti-rust treatment防錆処理
Anti-rust oil防錆油
see table below
L1
PCD 25 φ31 φ
18-
0.05
-0.
10
20
4
27
(17)30°
4-φ3.4
30°
(φ
7.9)
F
E-F下表参照
E
Standard products in stock PSR series標準在庫品 PSRシリーズ
PSR0812 Shaft dia.(軸径)φ8 Lead(リード)12mm C5
Unit(単位):mm
Ball Screw Specifications 諸元
Ball size ボール径 φ1.5875
Number of thread 条数 2
Thread direction 巻方向 Right 右
Shaft root dia. ねじ軸谷径 φ6.7
Number of circuit 循環数 1.6×2
Material材質
Shaft 軸 S55C+SUS303
Nut ナット SCM415H
Surface hardnessねじ部表面硬度
HRC58~(Thread area)
Lubrication出荷時封入剤
KSS Original Grease MSG No.2
0.005
0.010
R0.2max
下表参照 G
G
0.012 A
see table below
A
(φ
7.9)
0.005L2
L1
L4
L3
E
E
A
E
G0.010
(7)
4
7.5(22.5)
30
7
PCD 25
20
30°
4-φ3.4
30°
C0.3
M6x0.75
C0.5
30°x0.5
8 0-0.2
φ4.
5h6
0 -0.
008
3
φ6-
0.00
2-
0.00
7-0.
022
0φ
9.5h
8
φ31φ
18-
0.05
-0.
10
4
27
(17)
Standard products in stock PSRT series標準在庫品 PSRTシリーズ
PSRT0812 Shaft dia.(軸径)φ8 Lead(リード)12mm C5
Unit(単位):mm
Ball Screw Modelボールねじ型番
Travelストローク
Shaft lengthねじ軸長さ Travel deviation
代表移動量誤差ep
Total Run-out全振れ
Axial play軸方向すきま
Basic Load Rating基本定格荷重 N
L1
Dynamic動定格荷重
Ca
Static静定格荷重
Coa
PSR0812-230R230C5 195 230 ±0.023 0.065 ~0.005 2200 4000
Note) Please dsignate end-journal profile with your sketch. 注)軸端の追加工は図面とともにご指示ください。
Unit(単位):mm
Ball Screw Modelボールねじ型番
Travelストローク
Shaft lengthねじ軸長さ Travel deviation
代表移動量誤差ep
Total Run-out全振れ
Axial play軸方向すきま
Basic Load Rating基本定格荷重 N
L1 L2 L3 L4
Dynamic動定格荷重
Ca
Static静定格荷重
Coa
PSRT0812-169R210C5 135 169 173 180 210 ±0.020 0.065 ~0.005 2200 4000
Note) Please refer to page A321 for order code of end-journal machining. 注)追加工の呼び番号指定方法は、ページA321をご参照ください。
Supported-side end-journal profile 支持側端末加工形状
Support-unit Recommendation推奨サポートユニット
Supported-side 支持側 : MSU-6CS/6GSFixed-side 固定側 : MSU-6C/6G
L5:Thread length after end-journal machining. 追加工後のねじ部長さL6:Total length after end-journal machining. 追加工後全長
A04-φ08journal
A-type B-type C-type
6.8 +0.1 0
0.8 +0.1 0
φ5.
7 0 -0.
06
φ6-
0.00
2-
0.01
0
R0.2max
9
L6
L6
L5=L6-41
L5=L6-50
L5=L6-50
φ6-
0.00
2-
0.01
0
R0.2max 9
L6
A-type B-type C-type
D-type : Other than the above. 上記以外の形状
A341 A342
ボー
ルね
じBall Scresw
標準
在庫
品
PSR/PSRTシリ
ーズ
Standard products in stock PSR/PSRT series
ボー
ルね
じBall Scresw
標準
在庫
品
PSR/PSRTシリ
ーズ
Standard products in stock PSR/PSRT series
Unit(単位):mm
Ball Screw Specifications 諸元
Ball size ボール径 φ1.2
Number of thread 条数 1
Thread direction 巻方向 Right 右
Shaft root dia. ねじ軸谷径 φ9.0
Number of circuit 循環数 1×3
Material材質
Shaft 軸 S55C
Nut ナット SCM415H
Surface hardnessねじ部表面硬度
HRC58~(Thread area)
Anti-rust treatment防錆処理
Anti-rust oil防錆油
Standard products in stock PSR series標準在庫品 PSRシリーズ
PSR1002K Shaft dia.(軸径)φ10 Lead(リード)2mm C5
Unit(単位):mm
Ball Screw Specifications 諸元
Ball size ボール径 φ1.2
Number of thread 条数 1
Thread direction 巻方向 Right 右
Shaft root dia. ねじ軸谷径 φ9.0
Number of circuit 循環数 1×3
Material材質
Shaft 軸 S55C+SUS303
Nut ナット SCM415H
Surface hardnessねじ部表面硬度
HRC58~(Thread area)
Lubrication出荷時封入剤
KSS Original Grease MSG No.2
30°
4-φ4.5
21
PCD 26
30°
φ6h
6 0 -0.
008M8x1.0
C0.5
C0.5
4
4
10 0-0.2
R0.2以下9
(27)
(8)
φ11
.5h8
0 -0.
027
φ8-
0.00
2-
0.00
8
30°x0.5
37
10
5(14)
φ34φ
17-
0.05
-0.
10
C0.5
19
(φ
9.9)
0.005
0.011下表参照 G
G
0.012 A
see table below
A
0.005 E
E
A
E
G0.010
L2
L1
L4
L3
Standard products in stock PSRT series標準在庫品 PSRTシリーズ
PSRT1002K Shaft dia.(軸径)φ10 Lead(リード)2mm C5
see table below
L1
C0.5
21
30°
PCD 26
φ34(φ
9.9)
19
(14)5
4-φ4.5
30°
φ17-
0.05
-0.
10
F
E-F下表参照
E
Compact Nut / コンパクトナット
Unit(単位):mm
Ball Screw Modelボールねじ型番
Travelストローク
Shaft lengthねじ軸長さ Travel deviation
代表移動量誤差ep
Total Run-out全振れ
Axial play軸方向すきま
Basic Load Rating基本定格荷重 N
L1
Dynamic動定格荷重
Ca
Static静定格荷重
Coa
PSR1002K-230R230C5 205 230 ±0.023 0.055 ~0.005 1450 3000
Note) Please dsignate end-journal profile with your sketch. 注)軸端の追加工は図面とともにご指示ください。
Unit(単位):mm
Ball Screw Modelボールねじ型番
Travelストローク
Shaft lengthねじ軸長さ Travel deviation
代表移動量誤差ep
Total Run-out全振れ
Axial play軸方向すきま
Basic Load Rating基本定格荷重 N
L1 L2 L3 L4
Dynamic動定格荷重
Ca
Static静定格荷重
Coa
PSRT1002K-201R250C5 175 201 205 213 250 ±0.023 0.055 ~0.005 1450 3000
Note) Please refer to page A321 for order code of end-journal machining. 注)追加工の呼び番号指定方法は、ページA321をご参照ください。
Supported-side end-journal profile 支持側端末加工形状
Compact Nut / コンパクトナット
Support-unit Recommendation推奨サポートユニット
Supported-side 支持側 : MSU-8CS/8GSFixed-side 固定側 : MSU-8C/8G
L5:Thread length after end-journal machining. 追加工後のねじ部長さL6:Total length after end-journal machining. 追加工後全長
A04-φ10journal
A-type B-type C-type
L5=L6-49
6.8
0.8+0.1 0
+0.1 0
φ5.
7 0 -0.
06
φ6-
0.00
2-
0.01
0
R0.2max
9
L6
L5=L6-58
φ6-
0.00
2-
0.01
0
R0.2max9
L6
L5=L6-58
L6
A-type B-type C-type
D-type : Other than the above. 上記以外の形状
A343 A344
ボー
ルね
じBall Scresw
標準
在庫
品
PSR/PSRTシリ
ーズ
Standard products in stock PSR/PSRT series
ボー
ルね
じBall Scresw
標準
在庫
品
PSR/PSRTシリ
ーズ
Standard products in stock PSR/PSRT series
Unit(単位):mm
Ball Screw Specifications 諸元
Ball size ボール径 φ1.2
Number of thread 条数 1
Thread direction 巻方向 Right 右
Shaft root dia. ねじ軸谷径 φ11.0
Number of circuit 循環数 1×3
Material材質
Shaft 軸 S55C
Nut ナット SCM415H
Surface hardnessねじ部表面硬度
HRC58~(Thread area)
Anti-rust treatment防錆処理
Anti-rust oil防錆油
see table below
L1(Accuracy guaranteed area/精度保証範囲)
23
φ19-
0.05
-0.
10
φ36
PCD 28
C0.5
19
(14)530° 30°
(φ
11.9) F
E-F下表参照
E
4-φ4.5
Standard products in stock PSR series標準在庫品 PSRシリーズ
PSR1202K Shaft dia.(軸径)φ12 Lead(リード)2mm C5
Unit(単位):mm
Ball Screw Specifications 諸元
Ball size ボール径 φ1.2
Number of thread 条数 1
Thread direction 巻方向 Right 右
Shaft root dia. ねじ軸谷径 φ11.0
Number of circuit 循環数 1×3
Material材質
Shaft 軸 S55C+SUS303
Nut ナット SCM415H
Surface hardnessねじ部表面硬度
HRC58~(Thread area)
Lubrication出荷時封入剤
KSS Original Grease MSG No.2
0.005 E
A
φ8h
6 0 -0.
009
C0.5φ10-
0.00
2-
0.00
8
5
C0.5
30°x0.5
12 0-0.25
PCD 28
23
30° 30°
M10x1.0
4-φ4.5
φ14
h8 0 -0.
027
C0.5
19
(14) 5
φ19-
0.10
φ36
(φ
11.9) -0.
05
(10)
10
(30)
45
15
4
R0.2max
L2
L1
L4
L3
G0.010
0.012 A
下表参照 Gsee table below
0.005 E
0.011
E
A
G
Standard products in stock PSRT series標準在庫品 PSRTシリーズ
PSRT1202K Shaft dia.(軸径)φ12 Lead(リード)2mm C5
Unit(単位):mm
Ball Screw Modelボールねじ型番
Travelストローク
Shaft lengthねじ軸長さ Travel deviation
代表移動量誤差ep
Total Run-out全振れ
Axial play軸方向すきま
Basic Load Rating基本定格荷重 N
L1
Dynamic動定格荷重
Ca
Static静定格荷重
Coa
PSR1202K-280R280C5 255 280 ±0.023 0.055 ~0.005 1600 3700
Note) Please dsignate end-journal profile with your sketch. 注)軸端の追加工は図面とともにご指示ください。
Unit(単位):mm
Ball Screw Modelボールねじ型番
Travelストローク
Shaft lengthねじ軸長さ Travel deviation
代表移動量誤差ep
Total Run-out全振れ
Axial play軸方向すきま
Basic Load Rating基本定格荷重 N
L1 L2 L3 L4
Dynamic動定格荷重
Ca
Static静定格荷重
Coa
PSRT1202K-271R330C5 245 271 275 285 330 ±0.023 0.065 ~0.005 1600 3700
Note) Please refer to page A321 for order code of end-journal machining. 注)追加工の呼び番号指定方法は、ページA321をご参照ください。
Supported-side end-journal profile 支持側端末加工形状
Compact Nut / コンパクトナット Compact Nut / コンパクトナット
Support-unit Recommendation推奨サポートユニット
Supported-side 支持側 : ーFixed-side 固定側 : ー
L5:Thread length after end-journal machining. 追加工後のねじ部長さL6:Total length after end-journal machining. 追加工後全長
A04-φ12journal
A-type B-type C-type
10
7.9
R0.2max
L6
L5=L6-69
L6
L5=L6-6910
L6
L5=L6-59R0.2max
0.9+0.1 0
+0.1 0
φ8-
0.00
4-
0.01
2
φ7.
6 0 -0.
08
φ8
-0.
004
-0.
012
A-type B-type C-type
D-type : Other than the above. 上記以外の形状