Grease+Gard™ – What is it?

Market Issues

Grease+Gard™ Sales Opportunity

Grease+Gard™ Models

How Does It Work

The Agitator

Grease+Gard™ Operation

Installation/Applications

Listings/Certifications

Grease+Gard™ System Summary

• The first approved Grease Recovery Device (GRD) that can be used on above-the-floor and in-floor grease interceptor applications.

• Grease+Gard™ is also the first approved GRD application device that can also be used as a retrofit unit on most other manufacturers’ interceptors.

• Dealing with grease; dipping, pumping/disposal costs and cleaning pipe blockages

• Cleaning schedule, frequency and related high operating costs

• Meeting stringent discharge requirements and paying surcharges/fines for non-compliance

• Increasing enforcement and tightening of Federal regulations

• Grease+Gard™ Retrofit Skimmer (patent pending) is the only retrofit device intended for GRD applications on the market today

• The retrofit unit can be installed on most interceptors saving thousands in interceptor replacement costs

• The retrofit unit is a less expensive alternative to a standard grease recovery device

• Code approved

• Efficient and simple solutions for different applications

• Smith now has a competitive GRD that equals the competition

• New Construction– Regular Profile Grease+Gard™ GRD

• Fig. No. 8165 (20, 25, 35, 50 GPM)• Fig. No. 8166 Low Type Interceptor

(20, 35, 50 GPM)

– Low Profile Grease+Gard™ GRD• Fig. No. 8175 (20, 25, 35, 50 GPM)• Fig. No. 8176 Low Type Interceptor

(20, 35, 50 GPM)

Fig. No. 8165

Fig. No. 8175

• Retrofit• Fig. No. 8165GG - Grease+Gard™

Retrofit Skimmer

• Fig. No. 8175GG – Low Type Grease+Gard™ Retrofit Skimmer

Fig. No. 8165GG

Fig. No. 8175GG

• Indirect Solids Interceptor, Fig. No. 8960

• Inline Solids Interceptor, Fig. No. 8980

• Belt technology along with a heater and timer• The belt cycles through the grease layer• Grease sticks to the belt• The skimmer blades wipe the grease off the

belt• The grease goes off the skimmer blades and

into the grease trough• The grease trough feeds the grease into the

grease bucket where the grease is collected and removed daily to a barrel for proper disposal

Fig. No. 8165

Fig. No. 8175

• Patent pending technology

• Helps circulate the top grease layer

• Aids in drawing the grease to the belt

• Reduces having to stir the contents of the interceptor

• This GRD model can be used on most in floor and above floor interceptor applications.

• The tower is 13” high from the interceptor cover.

• Can add an extension to in ground applications if needed.

• Available in 20, 25, 35 and 50 GPM.

Regularly Furnished: Automatic Grease Recovery Device (GRD) with Type 304 Stainless steel Interceptor, No-Hub Connections, Flow Control Fitting, Heater and Grease+Gard™ Skimmer with Grease Reservoir.

• This model is designed to fit into tight spaces where there are clearance issues.

• It is designed for above floor installations only.

• The tower is 7” high from the interceptor cover.

• Available in 20, 25,35 and 50 GPM.

Regularly Furnished: Automatic Grease Recovery Device (GRD) with Low Profile Grease+Gard™ Skimmer and Grease Reservoir, Heater, Type 304 Stainless Steel Interceptor with No-Hub Connections and Flow Control Fitting.

• Retrofit on existing grease interceptor cover.

• The tower is 13” high.

• Requires a square cut out of the top of the interceptor for installation.

• This model can be used on most in-floor and some above floor interceptor applications.

Regularly Furnished: Stainless Steel Housing, Adjustable Timer, Skimming Belt, Mounting Base with Gasket, Heater and Removable Grease Reservoir.

• Retrofit on existing grease interceptor cover.

• The tower is 7” high.

• Requires a cut out of the top of the interceptor for installation.

• This model is designed to fit into tight spaces where there are clearance issues.

Regularly Furnished: Low Profile Stainless Steel Housing, Adjustable Timer, Skimming Belt, Mounting Plate with Gasket, Heater and Removable Grease Reservoir.

• Inline and indirect solid interceptor assemblies to be installed at the solids source.

• Primary and secondary straining systems in each system. Any solids due to erosion that pass the primary screen and sink to the bottom of the sump will be captured and removed by the filter bag.

• Patent Pending.

• Future capabilities of being semi automatic.

Regularly Furnished: Fabricated Type 304 Stainless Steel Body with Adjustable Legs, Perforated Bottom Bucket and Secondary Poly Mesh Strainer.

Regularly Furnished: Fabricated Type 304 Stainless Steel Body with Adjustable Legs, Perforated Bottom Bucket, Secondary Poly Mesh Strainer and Secured Cover.

• Restaurants

• Grocery/Convenience Stores

• Churches

• Casinos

• School Cafeterias

• Correctional Facilities

• Retirement Homes

• Mall Food Courts

• Airport Eateries

• Sports Arenas

Commercial Kitchen and Food Processing Applications

• IAPMO listed as a GRD for territories using the Uniform Plumbing Code (UPC).

• This IAPMO listing of our GRD’s is for both new installations and retrofit installations on other manufacturers’ Interceptors.

• The 8165GG and 8175GG are IAPMO listed through the MC (Material and Component) listing program.

• PDI Certified.• Tested and approved to the National Consensus

Standards ASME A112.14.3 and A112.14.4 – Grease Removal Devices.

• Smith now has the broadest product line of Grease and Solids Interceptors in the entire industry = more opportunities to close a sale to fit everyone’s budget or configurations.

• Grease+Gard™ Retrofit Skimmer (patent pending) is the only retrofit device for GRD applications on the market today.

• Grease+Gard™ Retrofit Skimmer can be installed on most interceptors saving thousands in interceptor replacement costs.

• The Retrofit Skimmers (8165GG and 8175GG) are less expensive alternatives to grease recovery devices.

• Approved, efficient and simple solutions for different applications.