View
240
Download
3
Category
Preview:
Citation preview
COMUNE DI OLBIA PIANO SVILUPPO RETE
VODAFONE
Città di Olbia: Mappa aree di potenziale interesse
(inclusi siti in sharing)
Comune di Olbia: mappa aeree di potenziale interesse
(inclusi siti in sharing)
Comune di Olbia: mappa repeater
Conclusioni
Con riferimento alle tavole precedentemente esposte, il piano di sviluppo di rete nei prossimi anni prevede:
- la realizzazione di nuove stazioni radio base e repeater per migliorare il
servizio voce e il servizio dati su tutto il territorio del comune di Olbia
- il potenziamento delle stazioni radio base attualmente in servizio per fornire i servizi mobili di ultima generazione (LTE/4G)
OFFICE Site name indirizzo
3OF06479 Olbia Frisca Rotonda via Roma ‐ via Re di puglia
3OF04995 Porto Rotondo est Lo. Porto Rotondo
3RM00630 Olbia Aeroporto 2 Aeroporto Costa Smeralda c/o Posto Polizia
3RM00869 Olbia Est Loc Sa Marinedda ‐ Via C.Pavese 6
3OF04958 Olbia Via Barcellona Rione S.Maria S.P. Olbia/Tempio
3OF00564 Olbia Sud via Imperia
3RM00631 Olbia Industriale 2 Loc. Isola Bianca ‐ Olbia
3OF10194 Enas FS Loc Sa Galdosa
3OF04221 Monte Aspro Monte aspro
3OF00654 Olbia Aeroporto S.S.199 ‐ Zona Aeroporto
3OF04220 Porto Rotondo Loc. Monte Maiori ‐ Porto Rotondo
3OF03349 Olbia su Porchile via Lucania, 1
3OF20149 Olbia BSC Piano lott. BASA lotto 30/32 Edif B2‐2
3OF00546 Pittulongu Località Pittulongu
3OF00986 Olbia Stadio Via F.Noce
3OF04409 Marina di Porto Rotondo Loc. Marina di Porto Rotondo
3RM01775 Golfo di Marinella SSI Località Marinella, Via Monte Maiore,44
3RM00846 Olbia nord SSI Via Palladio, 1
3OF00991 San Pantaleo Loc. Mura Alvara
3OF00980 Olbia Zona Industriale Impianto di Depurazione Consorzio
3OF04222 Olbia via De Filippi, 21B
3OF00544 Porto di Cugnana Porto di cugnana
3OF01842 Blu Olbia V.Aldo Moro S.S. 125Km 2,8 Palau
3RM02787 Olbia Capo Ceraso Loc Capo Ceraso
Siti on air
Nome sito Codice Office Indirizzo Latitudine (ED50) Longitudine (ED50) Foglio IGM
Olbia Frisca 3OF06479
Loc. Int. Via Roma, Via
Imperia, Via Re di Puglia 40° 55' 4.8'' 9° 29' 41.6'' foglio. 444 sez.IV
Frequenza ( Mhz)
Altezza centro elettrico (m) Orientamento gradi (°) Tilt elettrico (°) Tilt meccanico (°) Marca antenna Modello d'antenna Dimensione antenna
(m)
Potenza totale al connettore
d`Antenna (W)2100 19,06 120 6 6 RFS APX13GV‐15DWV‐15DWVBR‐C 2,12 40
2100 19,06 210 6 6 RFS APX13GV‐15DWV‐15DWVBR‐C 2,12 40
2100 19,06 350 2 0 RFS APX13GV‐15DWV‐15DWVBR‐C 2,12 40
Lista siti On Air
Nome sito Codice Office Indirizzo Latitudine (ED50) Longitudine (ED50) Foglio IGM
Porto Rotondo Est 3OF04995 Loc. Porto Rotondo 41° 1' 32.98'' 9° 33' 21.99'' foglio 428 sez.II
Frequenza ( Mhz) Altezza centro elettrico (m) Orientamento gradi (°) Tilt elettrico (°) Tilt meccanico (°) Marca antenna Modello d'antenna Dimensione antenna
(m)Potenza totale al connettore
d`Antenna (W)900 7,66 150 8 0 Kathrein 742264 1,316 65,5
900 7,77 275 10 0 Kathrein 80010290 1,54 65,5
2100 7,66 150 6 0 Kathrein 742264 1,316 76,3
2100 7,77 275 8 0 Kathrein 80010290 1,54 76,3
2100 7,77 355 6 0 Kathrein 80010290 1,54 76,3
Lista siti On Air
Sui sistemi GSM e DCS sono abilitate le funzionalità di DTX e PC: la potenza totale al connettore d'antenna fornita ne tiene conto secondo quanto previsto dalla norma CEI 211‐10 Par. 6.3.3
Nome sito Codice Office Indirizzo Latitudine (ED50) Longitudine (ED50) Foglio IGM
Olbia Aeroporto 2 3RM00630
Locali Aeroporto Costa
Smeralda 40° 54' 13.9'' 9° 30' 59.2'' foglio 444 sez I
Frequenza ( Mhz)Altezza centro
elettrico (m)Orientamento gradi (°) Tilt elettrico(°) Tilt meccanico (°) Marca antenna Modello d'antenna Dimensione antenna (m) Potenza totale al connettore
d`Antenna (W)
2100 18,06 50 2 0 RFS APX13GV‐15DWV‐15DWVBR‐C 2,12 40
2100 18,06 220 2 0 RFS APX13GV‐15DWV‐15DWVBR‐C 2,12 40
Lista siti On Air
Nome sito Codice Office Indirizzo Latitudine (ED50) Longitudine (ED50) Foglio IGM
Olbia Est 3RM00869
Loc. Sa Marinedda, Via
C.Pavese 6 40° 54' 38.97'' 9° 31' 25.88'' foglio 441 sez.I
Frequenza ( Mhz) Altezza centro elettrico (m) Orientamento gradi (°) Tilt elettrico (°) Tilt meccanico (°) Marca antenna Modello d'antenna Dimensione
antenna (m)Potenza totale al
connettore d`Antenna (W)
900 21,5 0 6 0 Kathrein 742265 1,916 85,48
900 21,5 100 6 0 Kathrein 742265 1,916 85,48
900 21,5 260 6 0 Kathrein 742265 1,916 85,48
2100 21,5 0 5 0 Kathrein 742265 1,916 40
2100 21,5 100 5 0 Kathrein 742265 1,916 40
2100 21,5 260 5 0 Kathrein 742265 1,916 40
Lista siti On Air
Nome sito Codice Office Indirizzo Latitudine (ED50) Longitudine (ED50) Foglio IGM
Olbia Via Barcellona 3OF04958
Via Barcellona, angolo
via Wagner 40° 55' 37.36'' 02° 58' 29.27'' foglio 29 mappale 359
Frequenza ( Mhz) Altezza centro elettrico (m) Orientamento gradi (°) Tilt elettrico(°) Tilt meccanico (°) Marca antenna Modello
d'antennaDimensione antenna
(m)Potenza totale al connettore
d`Antenna (W)
900 25 0 6 4 Kathrein 742265 1,916 42
900 25 120 6 4 Kathrein 742265 1,916 42
900 25 240 6 4 Kathrein 742265 1,916 42
2100 25 0 6 4 Kathrein 742265 1,916 40
2100 25 120 6 4 Kathrein 742265 1,916 40
2100 25 240 6 4 Kathrein 742265 1,916 40
Lista siti On Air
Nome sito Codice Office Indirizzo Latitudine (ED50) Longitudine (ED50) Foglio IGM
Olbia Sud 3OF00564 Via Imperia 40° 54' 35.5'' 09° 29' 56.82''
Frequenza ( Mhz) Altezza centro elettrico (m) Orientamento gradi (°) Tilt elettrico(°) Tilt meccanico (°) Marca
antennaModello
d'antennaDimensione antenna (m)
Potenza totale al connettore d`Antenna (W)
900 27 60 8 0 Kathrein 742265 1,916 42
900 27 180 8 0 Kathrein 742265 1,916 42
900 27 300 8 0 Kathrein 742265 1,916 42
1800 27 60 6 0 Kathrein 742265 1,916 42
1800 27 180 6 0 Kathrein 742265 1,916 42
1800 27 300 6 0 Kathrein 742265 1,916 42
2100 24,5 60 6 0 Kathrein 742213 1,942 40
2100 24,5 180 6 0 Kathrein 742213 1,942 40
2100 24,5 300 6 0 Kathrein 742213 1,942 40
Lista siti On Air
Nome sito Codice Office Indirizzo Latitudine (ED50) Longitudine (ED50) Foglio IGM
Olbia Industriale 2 3RM00631
Loc. Cabu
Abas
settore 1: 40° 56' 58.00''
settore 2: 40° 56' 57.71
settore 1: 9° 31' 33.61''
settore 2: 9° 31' 30.9'' Foglio 444 sez. I
Frequenza ( Mhz) Altezza centro elettrico (m)
Orientamento gradi (°) Tilt elettrico(°) Tilt meccanico (°) Marca antenna Modello
d'antenna
Dimensione antenna
(m)
Potenza totale al
connettore d`Antenna
(W)
900 5,31 180 6 0 Kathrein 742264 1,316 52
900 3,66 230 6 2 Kathrein 742264 1,316 60
2100 5,31 180 6 0 Kathrein 742264 1,316 40
2100 3,66 230 6 2 Kathrein 742264 1,316 40
Lista siti On Air
Nome sito Codice Office Indirizzo Latitudine (ED50) Longitudine (ED50) Foglio IGM
Hub Enas FS 3OF10194 Loc. Sa Galdosa 40° 51' 15'' 9° 26' 46.6'' Foglio 444 sez. III
Frequenza ( Mhz)
Altezza centro elettrico (m)
Orientamento gradi (°) Tilt elettrico(°) Tilt meccanico (°) Marca antenna Modello
d'antenna
Dimensione antenna
(m)
Potenza totale al
connettore d`Antenna
(W)
900 25 180 0 10 Kathrein 739623 1,936 42
900 25 230 0 10 Kathrein 739623 1,936 42
2100 25 180 6 4 Kathrein 742213 1,942 20
2100 25 230 6 4 Kathrein 742213 1,942 20
Lista siti On Air
Nome sito Codice Office Indirizzo Latitudine (ED50) Longitudine (ED50) Foglio IGM
Monte Aspro 3OF04221 Monte Aspro 40° 58' 49'' 9° 28' 3''
Frequenza ( Mhz) Altezza centro elettrico (m)
Orientamento gradi (°) Tilt elettrico (°) Tilt meccanico (°) Marca antenna Modello d'antenna Dimensione
antenna (m)Potenza totale al
connettore d`Antenna (W)
900 12,82 60 0 6 Kathrein 741327 1,916 42
900 12,82 150 0 6 Kathrein 741327 1,936 42
900 12,82 320 0 6 Kathrein 741327 1,936 42
1800 12,82 60 6 0 SIRA PTEL 19‐65/D 42
1800 12,82 150 6 0 SIRA PTEL 19‐65/D 42
1800 12,82 320 6 0 SIRA PTEL 19‐65/D 42
Lista siti On Air
Nome sito Codice Offi Indirizzo Latitudine (ED50) Longitudine (ED50) Foglio IGM
Olbia Aeroporto 3OF00654 S.S.199 ‐ Zona Aeroporto 40° 54' 27.1'' 9° 30' 26.3'' Fg 444 Sez I
Frequenza ( Mhz)
Altezza centro
elettrico (m)
Orientamento gradi (°) Tilt elettrico (°) Tilt meccanico (°) Marca antenna
Modello d'antenna
Dimensione antenna (m)
Potenza totale al connettore d`Antenna
(W)
900 24,96 60 8 4 Kathrein 742265 1,916 63,49
900 24,97 120 0 10 Kathrein 741327 1,936 63,49
900 24,97 240 0 4 Kathrein 741327 1,936 63,49
1800 24,97 120 0 10 Kathrein 741327 1,936 83,93
1800 24,97 240 0 4 Kathrein 741327 1,936 83,93
2100 24,96 60 6 4 Kathrein 742265 1,916 60
2100 24,65 120 6 4 Kathrein 742212 1,302 60
2100 24,65 240 6 0 Kathrein 742212 1,302 60
Lista siti On Air
Sui sistemi GSM e DCS sono abilitate le funzionalità di DTX e PC: la potenza totale al connettore d'antenna fornita ne tiene conto secondo quanto previsto dalla norma CEI
211‐10 Par. 6.3.3
Nome sito Codice Office Indirizzo Latitudine (ED Longitudine (Foglio IGM
Porto Rotondo 3OF04220 Loc. Monte Maiori 41° 1' 22.20'' 9° 33' 2.7'' foglio 428 ‐ Sez. II
Frequenza ( Mhz)
Altezza centro elettrico (m) Orientamento gradi (°) Tilt elettrico (°)
Tilt meccanico
(°)Marca antenna Modello d'antenna Dimensione antenna
(m)Potenza totale al connettore
d`Antenna (W)
900 4,74 120 8 4 Kathrein 742270 1,498 70,63
900 4,74 240 8 4 Kathrein 742270 1,498 70,63
900 4,74 350 8 4 Kathrein 742270 1,498 70,63
1800 4,74 120 6 4 Kathrein 742270 1,498 107,45
1800 4,74 240 6 4 Kathrein 742270 1,498 107,45
1800 4,74 350 6 4 Kathrein 742270 1,498 107,45
2100 4,74 120 6 4 Kathrein 742270 1,498 74,81
2100 4,74 240 6 4 Kathrein 742270 1,498 74,81
2100 4,74 350 6 4 Kathrein 742270 1,498 74,81
Lista siti On Air
Sui sistemi GSM e DCS sono abilitate le funzionalità di DTX e PC: la potenza totale al connettore d'antenna fornita ne tiene conto secondo quanto previsto dalla norma CEI 211‐10 Par.
6.3.3
Nome sito Codice Office Indirizzo Latitudine (ED50) Longitudine (ED50) Foglio IGM
Olbia Su Porchile 3OF03349 Via Lucania,1 40° 41' 34.5'' 9° 43' 31''
Frequenza ( Mhz) Altezza centro elettrico (m) Orientamento gradi (°) Tilt elettrico (°) Tilt meccanico (°) Marca antenna Modello
d'antennaDimensione antenna
(m)Potenza totale al connettore
d`Antenna (W)900 23,7 0 6 ‐2 Kathrein 742265 1,916 56
900 23,7 130 6 0 Kathrein 742265 1,916 50
900 23,7 240 6 ‐2 Kathrein 742265 1,916 56
1800 24,05 0 0 4 Kathrein 739494 1,302 60
1800 24,05 130 0 6 Kathrein 739494 1,302 50
1800 24,05 240 0 4 Kathrein 739494 1,302 60
2100 23,7 0 6 ‐2 Kathrein 742265 1,916 60
2100 23,7 130 6 0 Kathrein 742265 1,916 50
2100 23,7 240 6 ‐2 Kathrein 742265 1,916 60
Lista siti On Air
Nome sito Codice Office Indirizzo Latitudine (ED50) Longitudine (ED50) Foglio IGM
Olbia BSC 3OF20149
Pinao Lott. BASA lotoo 30/32
Edif B2‐2 40° 57' 43.76'' 9° 29' 20.77'' foglio 23, particella 1240
Frequenza ( Mhz) Altezza centro elettrico (m) Orientamento gradi (°) Tilt elettrico (°) Tilt meccanico (°) Marca antenna Modello d'antenna Dimensione
antenna (m)Potenza totale al connettore
d`Antenna (W)900 25 35 8 0 Kathrein 742265 1,916 58,14
900 25 150 8 0 Kathrein 742265 1,916 58,14
900 25 240 8 0 Kathrein 742265 1,916 58,14
2100 25 35 6 0 Kathrein 742213 1,942 39,63
2100 25 150 6 0 Kathrein 742213 1,942 39,63
2100 25 240 6 0 Kathrein 742213 1,942 39,63
Lista siti On Air
Nome sito Codice Office Indirizzo Latitudine (ED50) Longitudine (ED50) Foglio IGM
Pittulongu 3OF00546 Loc Pittulongu 40° 57' 4'' 9° 33' 56.3'' Foglio 444 sez.I
Frequenza ( Mhz)
Altezza centro elettrico (m)
Orientamento gradi (°) Tilt elettrico (°) Tilt meccanico (°) Marca antenna Modello
d'antennaDimensione antenna
(m)Potenza totale al connettore
d`Antenna (W)900 14,03 50 5 0 Kathrein 742271 1,916 34,78
900 14,03 130 6 0 Kathrein 742271 1,916 67,55
1800 14,03 130 6 0 Kathrein 742271 1,916 40
2100 14,03 50 6 0 Kathrein 742271 1,942 64,86
2100 14,03 130 6 0 Kathrein 742271 1,942 64,86
Lista siti On Air
Sui sistemi GSM e DCS sono abilitate le funzionalità di DTX e PC: la potenza totale al connettore d'antenna fornita ne tiene conto secondo quanto previsto dalla norma CEI 211‐10 Par. 6.3.3
Nome sito Codice Office Indirizzo Latitudine (ED50) Longitudine (ED50) Foglio IGM
Olbia Stadio 3OF00986 F.Noce 40° 55' 49.10'' 9° 29' 36.05'' foglio 444 Sez. I‐IV
Frequenza ( Mhz)
Altezza centro elettrico (m)
Orientamento gradi (°) Tilt elettrico (°) Tilt meccanico (°) Marca antenna Modello d'antenna Dimensione antenna
(m)Potenza totale al connettore
d`Antenna (W)900 29 0 8 4 Kathrein 742271v03 1,933 128,48
900 29 130 8 4 Kathrein 742271v03 1,933 128,48
900 29 240 8 0 Kathrein 742271v03 1,933 83,57
1800 29 0 6 4 Kathrein 742271v03 1,933 71,94
1800 29 130 6 4 Kathrein 742271v03 1,933 71,94
1800 29 240 6 0 Kathrein 742271v03 1,933 41,37
2100 29 0 6 4 Kathrein 742271v03 1,933 60
2100 29 130 6 4 Kathrein 742271v03 1,933 60
2100 29 240 6 0 Kathrein 742271v03 1,933 60
1800 31,3 0 6 4 Kathrein 80010622 1,415 40
1800 31,3 120 6 4 Kathrein 80010622 1,415 40
1800 31,3 240 6 4 Kathrein 80010622 1,415 40
Lista siti On Air
Sui sistemi GSM e DCS sono abilitate le funzionalità di DTX e PC: la potenza totale al connettore d'antenna fornita ne tiene conto secondo quanto previsto dalla norma CEI 211‐10 Par. 6.3.3
Nome sito Codice Office Indirizzo Latitudine (ED50)Longitudine (EDFoglio IGM
Marina di Porto Rotondo 3OF04409
Loc Marina di Porto
Rotondo 41° 01' 52'' 9° 32' 41.46''
Frequenza ( Mhz) Altezza centro elettrico (m) Orientamento gradi (°) Tilt elettrico (°) Tilt meccanico
(°) Marca antenna Modello d'antenna
Dimensione antenna (m)
Potenza totale al connettore d`Antenna
(W)900 7,25 135 3 0 Kathrein 742270 1,498 38,8
900 7,25 225 8 0 Kathrein 742270 1,498 46,56
1800 7,25 135 3 0 Kathrein 742270 1,498 28
1800 7,25 225 8 0 Kathrein 742270 1,498 42
2100 7,25 135 3 0 Kathrein 742270 1,498 60
2100 7,25 225 8 0 Kathrein 742270 1,498 60
Lista siti On Air
Nome sito Codice Office Indirizzo Latitudine (ED50) Longitudine (ED50) Foglio IGM
Golfo di Marinella SSI 3RM01775
Loc. Marinella ‐ Via
Monte Maiore, 44 41° 00' 39.1 9° 32' 55.9'' foglio 428 sez. II
Frequenza ( Mhz) Altezza centro elettrico (m) Orientamento gradi (°) Tilt elettrico (°) Tilt meccanico (°) Marca antenna Modello
d'antennaDimensione antenna
(m)Potenza totale al connettore
d`Antenna (W)900 13,5 10 6 4 Kathrein 742271v03 1,933 66,22
900 13,5 110 6 4 Kathrein 742271v03 1,933 66,22
900 13,5 310 6 2 Kathrein 742271v03 1,933 66,22
1800 13,5 10 6 4 Kathrein 742271v03 1,933 40
1800 13,5 110 6 4 Kathrein 742271v03 1,933 40
1800 13,5 310 6 2 Kathrein 742271v03 1,933 40
2100 13,5 10 6 4 Kathrein 742271v03 1,933 67,76
2100 13,5 110 6 4 Kathrein 742271v03 1,933 67,76
2100 13,5 310 6 2 Kathrein 742271v03 1,933 67,76
Lista siti On Air
Sui sistemi GSM e DCS sono abilitate le funzionalità di DTX e PC: la potenza totale al connettore d'antenna fornita ne tiene conto secondo quanto previsto dalla norma CEI 211‐10 Par. 6.3.3
Nome sito Codice Office Indirizzo Latitudine (ED50) Longitudine (ED50) Foglio IGM
Olbia Nord SSI 3RM00846 via Palladio, 1 40° 56' 6'' 9° 29' 51.5'' foglio 444 sez.IV
Frequenza ( Mhz) Altezza centro elettrico (m)
Orientamento gradi (°) Tilt elettrico (°) Tilt meccanico (°) Marca antenna Modello d'antenna Dimensione antenna
(m)
Potenza totale al connettore d`Antenna
(W)900 38 10 10 4 Kathrein 742265 1,916 60
900 39 150 10 4 Kathrein 742265 1,916 60
900 42 260 10 4 Kathrein 742265 1,916 60
2100 38 10 6 4 Kathrein 742265 1,916 40
2100 39 150 6 4 Kathrein 742265 1,916 40
2100 42 260 6 4 Kathrein 742265 1,916 40
Lista siti On Air
Nome sito Codice Office Indirizzo Latitudine (ED50) Longitudine (ED50) Foglio IGM
San Pantaleo 3OF00991 Loc. Mura Alvara 41° 02' 48.5'' 9° 28' 50.1'' foglio 428 sez.III
Frequenza ( Mhz) Altezza centro elettrico (m) Orientamento gradi (°) Tilt elettrico (°) Tilt meccanico (°) Marca antenna Modello
d'antennaDimensione antenna
(m)Potenza totale al connettore
d`Antenna (W)900 2,4 170 10 0 Kathrein 742265 1,916 65,52
900 2,5 285 10 0 Kathrein 742265 1,916 71,28
2100 2,4 170 6 0 Kathrein 742265 1,916 60
2100 2,5 285 6 0 Kathrein 742265 1,916 60
Lista siti On Air
Nome sito Codice Office Indirizzo Latitudine (ED50) Longitudine (ED50) Foglio IGM
Olbia Zona Industriale 3OF00980
via Indonesia/ impianto di
depurazione Consorzio Olbia 40° 56' 8.03'' 2° 55' 43.60'' foglio 34 mappale 1332
Frequenza ( Mhz) Altezza centro elettrico (m) Orientamento gradi (°) Tilt elettrico (°) Tilt meccanico (°) Marca antenna Modello d'antenna Dimensione antenna
(m)Potenza totale al
connettore d`Antenna (W)
900 25 20 0 6 Kathrein 741327 1,936 60
900 25 110 6 4 Kathrein 742271 2,058 60
900 25 180 6 4 Kathrein 742265 1,916 60
900 25 260 6 4 Kathrein 742271 2,058 60
1800 25 20 0 6 Kathrein 741327 1,936 60
1800 25 110 6 4 Kathrein 742271 2,058 60
1800 25 260 6 4 Kathrein 742271 2,058 60
2100 25 20 8 2 Kathrein 742212 1,302 40
2100 25 110 6 4 Kathrein 742271 2,058 40
2100 25 180 6 4 Kathrein 742265 1,916 40
2100 25 260 6 4 Kathrein 742271 2,058 40
Lista siti On Air
Nome sito Codice Office Indirizzo Latitudine (ED50) Longitudine (ED50) Foglio IGM
Olbia 3OF04222 via De Filippi, 21B 40° 55' 23.46'' 9° 30' 11.46'' foglio 444 sez. IV
Frequenza ( Mhz) Altezza centro elettrico (m)
Orientamento gradi (°) Tilt elettrico (°) Tilt meccanico (°) Marca antenna Modello
d'antennaDimensione antenna (m)
Potenza totale al connettore d`Antenna
(W)900 50,3 0 0 2 Kathrein 739623 1,936 118,71
900 53,8 120 0 3 Kathrein 739623 1,936 97,45
900 51,8 240 0 2 Kathrein 739623 1,936 126,27
1800 49,95 0 0 0 Kathrein 742234 1,302 87,3
1800 53,45 120 3 0 Kathrein 742234 1,302 85,43
1800 51,45 240 2 0 Kathrein 742234 1,302 79,36
2100 49,95 0 8 0 Kathrein 742234 1,302 60
2100 53,45 120 8 0 Kathrein 742234 1,302 60
2100 51,45 240 8 0 Kathrein 742234 1,302 60
Lista siti On Air
Nome sito Codice Office Indirizzo Latitudine (ED50) Longitudine (ED50) Foglio IGM
Porto di Cugnana 3OF00544 Loc. Porto di Cugnana 41° 01' 24.1'' 9° 30' 58.1'' foglio 428 sez.III
Frequenza ( Mhz) Altezza centro elettrico (m) Orientamento gradi (°) Tilt elettrico (°) Tilt meccanico (°) Marca antenna Modello d'antenna Dimensione antenna (m) Potenza totale al connettore
d`Antenna (W)
900 8 100 4 4 Kathrein 742265 1,916 103,32
900 8 220 0 4 Kathrein 742265 1,916 68,88
1800 7,65 100 0 4 Kathrein 739494 1,302 71,88
1800 7,65 220 0 4 Kathrein 739494 1,302 35,94
2100 8 100 6 4 Kathrein 742265 1,916 60
2100 8 220 4 4 Kathrein 742265 1,916 60
Lista siti On Air
Nome sito Codice Office Indirizzo Latitudine (ED50) Longitudine (ED50) Foglio IGM
Blu Olbia V.Aldo Moro 3OF01842 S.S.125 km 2.8, Palau 40° 56' 45.5'' 9° 29' 43.6'' foglio 444 sez.I‐IV
Frequenza ( Mhz) Altezza centro elettrico (m) Orientamento gradi (°) Tilt elettrico (°) Tilt meccanico (°) Marca antenna Modello
d'antennaDimensione antenna (m)
Potenza totale al connettore
d`Antenna (W)1800 18,65 10 8 0 Kathrein 742234 1,304 93,54
1800 18,65 100 4 0 Kathrein 742234 1,304 93,54
1800 18,65 190 8 0 Kathrein 742234 1,304 93,54
2100 18,65 10 6 0 Kathrein 742234 1,304 60
2100 18,65 100 4 0 Kathrein 742234 1,304 60
2100 18,65 190 6 0 Kathrein 742234 1,304 60
Lista siti On Air
Sui sistemi GSM e DCS sono abilitate le funzionalità di DTX e PC: la potenza totale al connettore d'antenna fornita ne tiene conto secondo quanto previsto dalla norma CEI 211‐10 Par.
6.3.3
Nome sito Codice Office Indirizzo Latitudine (ED50) Longitudine (ED50) Foglio IGM
Olbia Capo Ceraso 3OF02000 Loc Capo Ceraso 40° 54' 9.4'' 9° 36' 10'' foglio 444 sez.I
Frequenza ( Mhz) Altezza centro elettrico (m)
Orientamento gradi (°) Tilt elettrico (°) Tilt meccanico (°) Marca antenna Modello d'antenna Dimensione antenna (m) Potenza totale al
connettore d`Antenna (W)
900 21 60 10 0 Kathrein 742226 0,579 88,44
900 21 160 4 0 Kathrein 742226 0,579 44,22
2100 21 60 10 0 Kathrein 742226 0,579 60,39
2100 21 160 4 0 Kathrein 742226 0,579 60,39
Lista siti On Air
CI-10511-AMounting accessories are not included in the scope of delivery (see page 176 – 183)
Eurocell F-Panels GSM 1800 – Dual Polarization+45°/ -45° Polarization65° Half-power Beam Width
Input 2 x 7-16 femaleConnector position Bottom or topFrequency range 1710 – 1880 MHzVSWR < 1.5Gain 2 x 18 dBiImpedance 50 ΩPolarization +45°; -45°Front-to-back ratio, copolar > 30 dBHalf-power beam width +45° polarization
Horizontal: 65°, vertical: 6.5°-45° polarization
Horizontal: 65°, vertical: 6.5°Isolation > 30 dBMax. power per input 200 Watt (at 50 °C ambient temperature)Weight 6 kgWind load Frontal: 310 N (at 150 km/h)
Lateral: 110 N (at 150 km/h)Rearside: 250 N (at 150 km/h)
Max. wind velocity 200 km/hPacking size 1404 x 172 x 72 mmHeight/width/depth 1302 / 155 / 49 mm
Type No. 739 494
XPol F-Panel 1800 65° 18dBi
65°120°
dB
10
3
0
6.5°
dB
10
3
0
Horizontal Pattern
Vertical Pattern
Input 2 x 7-16 femaleConnector position Bottom TopFrequency range 1710 – 1990 MHzVSWR < 1.4 (1710 – 1880 MHz)
< 1.5 (1880 – 1990 MHz)Gain 2 x 18 dBiImpedance 50 ΩPolarization +45°; -45°Front-to-back ratio, copolar > 30 dBHalf-power beam width +45° polarization
Horizontal: 65°, vertical: 7°, 2°T-45° polarization
Horizontal: 65°, vertical: 7°, 2°TIsolation > 30 dBMax. power per input 200 Watt (at 50 °C ambient temperature)Weight 6 kgWind load Frontal: 310 N (at 150 km/h)
Lateral: 110 N (at 150 km/h)Rearside: 250 N (at 150 km/h)
Max. wind velocity 200 km/hPacking size 1404 x 172 x 72 mmHeight/width/depth 1302 / 155 / 49 mm
Type No. 739 495 741 444
XPol F-Panel 1800/1900 65° 18dBi 2°T
65°120°
dB
10
3
0
Horizontal Pattern
dB
10
3
0
7°
Vertical Pattern2° electr. downtilt
Vertical Pattern: – 2° electr. downtilt– first nullfill below horizon better or equal -25 dB below maximum gain– sidelobe suppression above horizon for first sidelobe better or equal 14 dB
below maximum gain.
A-PanelDual PolarizationHalf-power Beam Width
936.
1523
/f
S
ubje
ct t
o al
tera
tion.
Input 2 x 7-16 female
Connector position* Bottom or top
Weight 12 kg
Wind load Frontal: 330 N (at 150 km/h)Lateral: 200 N (at 150 km/h)Rearside: 770 N (at 150 km/h)
Max. wind velocity 200 km/h
Packing size 2057 x 287 x 165 mm
Height/width/depth 1936 / 262 / 116 mm
Mechanical specifications
page 1 of 2 739 623
Horizontal Pattern Vertical Pattern
first null-fill below horizon better or equal –25 dB below
maximum gain
65°120°
dB
10
3
0
9.5°
dB
10
3
0
880 – 960 MHz: +45°/–45° Polarization
Horizontal Pattern Vertical Pattern
first null-fill below horizon better or equal –25 dB below
maximum gain
10
3
0
68°130°
dB
10°
dB
10
3
0
806 – 894 MHz: +45°/–45° Polarization
X
65°
* Inverted mounting:Connector position top: Change drain hole screw.
806–960–45°
806–960+45°
7-16 7-16
806–960
739 623Type No.
Frequency range806 – 894 MHz 880 – 960 MHz
Polarization +45°, –45° +45°, –45°
Gain 2 x 16.5 dBi 2 x 17 dBi
Half-power beam width Horizontal: 68° Horizontal: 65°Copolar +45°/ –45° Vertical: 10° Vertical: 9.5°
Sidelobe suppression for ≥ 15 dBfirst sidelobe above horizon
Front-to-back ratio, copolar > 30 dB
Isolation > 30 dB
Impedance 50 Ω
VSWR < 1.5
Intermodulation IM3 < –150 dBc(2 x 43 dBm carrier)
Max. power per input 600 W (at 50 °C ambient temperature)
XPol A-Panel 806–960 65° 17dBi
806–960
KATHREIN-Werke KG . Anton-Kathrein-Straße 1 – 3 . PO Box 10 04 44 . D-83004 Rosenheim . Germany . Telephone +49 8031 1 84-0 . Fax +49 8031 1 84-9 73
Internet: http://www.kathrein.de
Please note: As a result of more stringent legal regulations and judgements regarding product liability, we are obliged to point out certain risks that may arise when products are used under extraordinary operatingconditions.
The mechanical design is based on the environmental conditions as stipulated in ETS 300 019-1-4, whichincludes the static mechanical load imposed on an antenna by wind at maximum velocity.Extraordinary operating conditions, such as heavy icing or exceptional dynamic stress (e.g. strain caused byoscillating support structures), may result in the breakage of an antenna or even cause it to fall to the ground.These facts must be considered during the site planning process.
The installation team must be properly qualified and also be familiar with the relevant national safetyregulations.The details given in our data sheets have to be followed carefully when installing the antennas andaccessories.The limits for the coupling torque of RF-connectors, recommended by the connector manufacturersmust be obeyed.
Any previous datasheet issues have now become invalid.
936.
1523
/f
S
ubje
ct t
o al
tera
tion.
Material: Reflector screen: Weather-proof aluminum.Fiberglass housing: It covers totally the internal antenna components.The special design reduces the sealing areas to a minimum andguarantees the best weather protection. Fiberglass material guaranteesoptimum performance with regards to stability, stiffness, UV resistanceand painting. The colour of the radome is light grey.All screws and nuts: Stainless steel.
Grounding: The metal parts of the antenna including the mounting kit and the innerconductors are DC grounded.
Environmental conditions: Kathrein cellular antennas are designed to operate under the environ-mental conditions as described in ETS 300 019-1-4 class 4.1 E. The antennas exceed this standard with regard to the following items:– Low temperature: –55 °C– High temperature (dry): +60 °C
Ice protection: Due to the very sturdy antenna construction and theprotection of the radiating system by the radome, the antenna remainsoperational even under icy conditions.
Environmental tests: Kathrein antennas have passed environmental tests as recommended in ETS 300 019-2-4. The homogenous design of Kathrein’s antennafamilies use identical modules and materials. Extensive tests have beenperformed on typical samples and modules.
For downtilt mounting use the clamps for an appropriate mast diameter together with the downtilt kit.Wall mounting: No additional mounting kit needed.
Accessories (order separately)
731 651 1 clamp Mast: 28 – 64 mm diameter 330 g 2
738 546 1 clamp Mast: 50 – 115 mm diameter 1.0 kg 2
733 677 1 clamp Mast: 60 – 115 mm diameter 2.0 kg 2
733 678 1 clamp Mast: 115 – 210 mm diameter 2.6 kg 2
733 679 1 clamp Mast: 210 – 380 mm diameter 4.0 kg 2
733 680 1 clamp Mast: 380 – 521 mm diameter 5.3 kg 2
737 975 1 downtilt kit Downtilt angle: 0° – 11° 2.8 kg 1
Type No. Description RemarksWeight Units perapprox. antenna
A-PanelsThe Advanced Antenna TechnologyFor Cross Polarization
739 623 page 2 of 2
-45° +45°
58
262
116
6472
9
2030
1990
1936
Bottom view
KATHREIN-Werke KG . Anton-Kathrein-Straße 1 – 3 . PO Box 10 04 44 . D-83004 Rosenheim . Germany . Telephone +49 8031 1 84-0 . Fax +49 8031 1 84-9 73
Internet: http://www.kathrein.de
Mounting accessories are not included in the scope of delivery
Dual-band A-PanelDual PolarizationHalf-power Beam Width
Input 4 x 7-16 female
Connector position* Bottom or top
Weight 19 kg
Wind load Frontal: 330 N (at 150 km/h)Lateral: 200 N (at 150 km/h)Rearside: 770 N (at 150 km/h)
Max. wind velocity 200 km/h
Packing size 2057 x 287 x 165 mm
Height/width/depth 1936 / 262 / 116 mm
Mechanical specificationsHorizontal Pattern Vertical Pattern
65°120°
dB
10
3
0
3 dB
10
0
9.5°
Horizontal Pattern Vertical Pattern
60°115°
dB
10
3
0
+45°/–45° Polarization
5.5°
dB
10
3
0
+45°/–45° Polarization900
1800
1800900
XX
60°65°
* Inverted mounting:Connector position top: Change drain hole screw.
741 327Type No.
1800–45°
900–45°
900+45°
1800+45°
7-16 7-16 7-16 7-16
Frequency range 900 1800870 – 960 MHz 1710 – 1880 MHz
Polarization +45°, –45° +45°, –45°
Gain 2 x 17 dBi 2 x 18.5 dBi
Half-power beam width Horizontal: 65° Horizontal: 60°Copolar +45°/ –45° Vertical: 9.5° Vertical: 5.5°
Sidelobe suppression for > 15 dBfirst sidelobe above horizon
Front-to-back ratio, copolar > 30 dB > 30 dB
Isolation, between ports > 30 dB (GSM 900 – GSM 900)1> 30 dB (GSM 1800 – GSM 1800)> 30 dB (GSM 900 – GSM 1800)
Impedance 50 Ω 50 Ω
VSWR < 1.5 < 1.5
Intermodulation IM3 < –150 dBc < –150 dBc(2 x 43 dBm carrier)
Max. power per input 400 Watt 200 Watt(at 50 °C ambient temperature)
XXPol A-Panel 900/1800 65°/60° 17/18.5dBi
900 1800
Multi-band F-PanelDual PolarizationHalf-power Beam WidthAdjust. Electrical Downtiltset by hand or by optional RCU (Remote Control Unit)
936.
2051
/i
S
ubje
ct t
o al
tera
tion.
Input 2 x 7-16 female
Connector position Bottom
Adjustment 1x, Position bottommechanism continuously adjustable
Weight 7.5 kg
Wind load Frontal: 130 N (at 150 km/h)Lateral: 110 N (at 150 km/h)Rearside: 310 N (at 150 km/h)
Max. wind velocity 200 km/h
Packing size 1574 x 172 x 92 mm
Height/width/depth 1302 / 155 / 69 mm
Mechanical specifications
page 1 of 4 742 212
1710–2170
X
65°
0°–8°
1710–2170–45°
1710–2170+45°
7-16 7-16
Horizontal Pattern Vertical Pattern0°–8° electrical downtilt
10
3
0
67°125°
dB dB
10
3
0
7°
Horizontal Pattern Vertical Pattern0°–8° electrical downtilt
65°120°
dB
10
3
0
1850 – 1990 MHz: +45°/–45° Polarization
6.7°
dB
10
3
0
1710 – 1880 MHz: +45°/–45° Polarization
Horizontal Pattern Vertical Pattern0°–8° electrical downtilt
63°120°
dB
10
3
0
1920 – 2170 MHz: +45°/–45° Polarization
6.5°
dB
10
3
0
742 212Type No.
Frequency range1710 – 1880 MHz 1850 – 1990 MHz 1920 – 2170 MHz
Polarization +45°, –45° +45°, –45° +45°, –45°
Gain 2 x 17.5 dBi 2 x 17.7 dBi 2 x 18 dBi
Half-power beam width Horizontal: 67° Horizontal: 65° Horizontal: 63°Copolar +45°/ –45° Vertical: 7° Vertical: 6.7° Vertical: 6.5°
Electrical tilt 0°–8° 0°–8° 0°–8°continuously adjustable
Sidelobe suppression for 0° ... 2° ... 5° ... 8° T 0° ... 2° ... 5° ... 8° T 0° ... 2° ... 5° ... 8° Tfirst sidelobe above horizon 17 ... 17 ... 15 .... 15 dB 20 ... 20 ... 18 ... 18 dB 20 ... 20 ... 18 ... 16 dB
Front-to-back ratio Copolar: > 30 dB Copolar: > 30 dB Copolar: > 30 dB(180° ± 30°) Total power: > 25 dB Total power: > 25 dB Total power: > 25 dB
Cross polar ratioMaindirection 0° Typically: 25 dB Typically: 25 dB Typically: 25 dBSector ±60° > 10 dB > 10 dB > 10 dB
Isolation, between ports > 30 dB > 30 dB > 30 dB
Impedance 50 Ω 50 Ω 50 ΩVSWR < 1.5 < 1.5 < 1.5
Intermodulation IM3 < –150 dBc(2 x 43 dBm carrier)
Max. power per input 300 W (at 50 °C ambient temperature)
XPol F-Panel 1710–2170 65° 18dBi 0°–8°T
1710–2170
KATHREIN-Werke KG . Anton-Kathrein-Straße 1 – 3 . PO Box 10 04 44 . D-83004 Rosenheim . Germany . Telephone +49 8031 1 84-0 . Fax +49 8031 1 84-9 73
Internet: http://www.kathrein.de
Please note: As a result of more stringent legal regulations and judgements regarding product liability, we are obliged to point out certain risks that may arise when products are used under extraordinary operatingconditions.
The mechanical design is based on the environmental conditions as stipulated in ETS 300 019-1-4, whichincludes the static mechanical load imposed on an antenna by wind at maximum velocity.Extraordinary operating conditions, such as heavy icing or exceptional dynamic stress (e.g. strain caused byoscillating support structures), may result in the breakage of an antenna or even cause it to fall to the ground.These facts must be considered during the site planning process.
The installation team must be properly qualified and also be familiar with the relevant national safetyregulations.The details given in our data sheets have to be followed carefully when installing the antennas andaccessories.The limits for the coupling torque of RF-connectors, recommended by the connector manufacturersmust be obeyed.
Any previous datasheet issues have now become invalid.
936.
2051
/i
S
ubje
ct t
o al
tera
tion.
Material: Reflector screen: Tin plated copper. Radiator: Tin plated zinc.Flat fiberglass radome: The max. radome depth is only 69 mm. Fiber-glass material guarantees optimum performance with regards to stability,stiffness, UV resistance and painting. The colour of the radome is grey.All screws and nuts: Stainless steel.
Grounding: The metal parts of the antenna including the mounting kit and the innerconductors are DC grounded.
Environmental conditions: Kathrein cellular antennas are designed to operate under the environ-mental conditions as described in ETS 300 019-1-4 class 4.1 E. The antennas exceed this standard with regard to the following items:– Low temperature: –55 °C– High temperature (dry): +60 °C
Ice protection: Due to the very sturdy antenna construction and theprotection of the radiating system by the radome, the antenna remainsoperational even under icy conditions.
Environmental tests: Kathrein antennas have passed environmental tests as recommended in ETS 300 019-2-4. The homogenous design of Kathrein’s antennafamilies use identical modules and materials. Extensive tests have beenperformed on typical samples and modules.
F-PanelsHarmony of Design and Technology
742 212 page 2 of 4
KATHREIN-Werke KG . Anton-Kathrein-Straße 1 – 3 . PO Box 10 04 44 . D-83004 Rosenheim . Germany . Telephone +49 8031 1 84-0 . Fax +49 8031 1 84-9 73
Internet: http://www.kathrein.de
54
155
69
Adjustmentmechanismwith integratedscale
Bottom view
∅ 8.5
–45° +45°
6435
1302
1356
1386For downtilt mounting use the clamps for an appropriate mast diameter together with the downtilt kit.
Wall mounting: No additional mounting kit needed.
Accessories (order separately)
734 360 2 clamps Mast: 34 – 60 mm dia. Stainless steel 60 g 1
734 361 2 clamps Mast: 60 – 80 mm dia. Stainless steel 70 g 1
734 362 2 clamps Mast: 80 – 100 mm dia. Stainless steel 80 g 1
734 363 2 clamps Mast: 100 – 120 mm dia. Stainless steel 90 g 1
734 364 2 clamps Mast: 120 – 140 mm dia. Stainless steel 110 g 1
734 365 2 clamps Mast: 45 – 125 mm dia. Stainless steel 80 g 1
738 546 1 clamp Mast: 50 – 115 mm dia. Hot-dip galvanized steel 1.0 kg 2
850 10002 1 clamp Mast: 110 – 220 mm dia. Hot-dip galvanized steel 2.7 kg 2
850 10003 1 clamp Mast: 210 – 380 mm dia. Hot-dip galvanized steel 4.8 kg 2
732 317 1 downtilt kit Downtilt angle: 0° – 10° Stainless steel 1.0 kg 1
Type No. Description Remarks MaterialWeight Units perapprox. antenna
936.
2051
/i
S
ubje
ct t
o al
tera
tion.
page 3 of 4 742 212
KATHREIN-Werke KG . Anton-Kathrein-Straße 1 – 3 . PO Box 10 04 44 . D-83004 Rosenheim . Germany . Telephone +49 8031 1 84-0 . Fax +49 8031 1 84-9 73
Internet: http://www.kathrein.de
Instructions for Antennaswith Adjustable Electrical Downtilt(General Example)
Manual adjustment procedure:(General example)
Remove protective cap. Set downtilt angle by rotatingthe adjustment wheel.
Screw on the protective capagain.
max.° – 0°
0° – max.°
Description of the interface (protective cap removed):
➀ Adjustment wheel withtwist-lock function.
➁ Downtilt spindle with inte-grated scale.
➀ Thread for fixing of theprotective cap or the RCU(Remote Control Unit).
➁ Gearwheel for RCU-powerdrive.
To set the downtilt angleexactly, you must look hori-zontally at the scale. Thelower edge of the gearwheelmust be used for alignmentpurposes.
1
22
1
936.
2051
/i
S
ubje
ct t
o al
tera
tion.
742 212 page 4 of 4
KATHREIN-Werke KG . Anton-Kathrein-Straße 1 – 3 . PO Box 10 04 44 . D-83004 Rosenheim . Germany . Telephone +49 8031 1 84-0 . Fax +49 8031 1 84-9 73
Internet: http://www.kathrein.de
Attachment of the RCU(General Example)
Attachment of the RCU (Remote Control Unit) for remote-controlled downtilt adjustment:(General example)
Remove the protective capcompletely from the antenna.
Check the proper functioningof the phase-shifter over theentire adjustment range, bytwisting the adjustment wheelin such a way that the spindlemoves completely in and out.
Reset the downtilt to theprevious value.
Completely remove the blackadjustement wheel by simplypulling it downwards.
Push the attachment nut ofthe RCU down towards thehousing.
Place the RCU carefully overthe adjustment spindle,observing the correct align-ment of the RCU with regardsto the antenna, i.e. the flatsurfaces of the attachmentfixture on the antenna sideand those inside the RCUhousing must lie flat againsteach other.
Push-up the RCU carefully tothe stop at the antenna.
Please note!Do not twist the RCU in any way during attaching tothe antenna, as this coulddamage the adjustmentspindle.
Tighten the RCU attachmentnut using a torque-wrench;wrench width = 41 mm, min. torque = 15 Nm,max. torque = 18 Nm.
Connect the RCU controlcable immediately afterattachment of the RCU.
Please note!In cases where a mechani-cal downtilt unit is installed,this must not be set for a downtilt of more than14 degrees.
Kathrein Inc., Scala Division Post Office Box 4580 Medford, OR 97501 (USA) Phone: (541) 779-6500 Fax: (541) 779-3991Email: communications@kathrein.com Internet: www.kathrein-scala.com
Kathrein’s dual band antennas are ready for 3G applications, covering all existing wireless bands as well as all spectrum under consideration for future systems, AMPS, PCS and 3G/UMTS. These cross-polarized antennas offer diversity operation in the same space as a conventional 800 MHz antenna, and are mountable on our compact sector brackets.
• Wide band operation.
• Exceptional intermodulation characteristics.
• High strength pultruded fiberglass radome.
General specifications: Frequency range 806–960 MHz
1710–2170 MHz
VSWR <1.5:1
Impedance 50 ohms
Intermodulation (2x20w) IM3: <-150 dBc
Polarization +45° and -45°
Connector 4 x 7/16 DIN female
Isolation intrasystem >30 dB intersystem >45 dB (806–960 // 1710–2170 MHz)
Weight 16.5 lb (7.5 kg)
Dimensions 22.8 x 10.3 x 5.5 inches (579 x 262 x 139 mm)
Equivalent flat plate area 1.73 ft2 (0.161 m2)
Wind survival rating* 120 mph (200 kph)
Shipping dimensions 29 x 11.9 x 7.6 inches (736 x 302 x 192 mm)
Shipping weight 21 lb (9.5 kg)
Mounting Fixed mount options are available for 2 to 4.6 inch (50 to 115 mm) OD masts. Panel may be inverted.
See reverse for order information.
* Mechanical design is based on environmental conditions as stipulated in EIA-222-F (June 1996) and/or ETS 300 019-1-4 which include the static mechanical load imposed on an antenna by wind at maximum velocity. See the Engineering Section of the catalog for further details.
806–960 MHz
1710–2170 MHz
742 226
65° Dualband Directional Antenna
10715-D 936.2949
Horizontal pattern ±45°-polarization
Vertical pattern ±45°-polarization
Horizontal pattern ±45°-polarization
Vertical pattern ±45°-polarization
Specifications: 806–866 MHz 824–894 MHz 880–960 MHz 1710–1880 MHz 1850–1990 MHz 1920–2170 MHzGain 11.1 dBi 11.4 dBi 11.8 dBi 12.8 dBi 13.3 dBi 13.6 dBi
Front-to-back ratio co-polar >23 dB >23 dB >25 dB >25 dB >25 dB >25 dB total power (180° ± 30°) >20 dB >20 dB >22 dB >22 dB >22 dB >22 dB
Maximum power per input 250 watts (at 50°C) 250 watts (at 50°C) 250 watts (at 50°C) 200 watts (at 50°C) 200 watts (at 50°C) 200 watts (at 50°C)
+45° and -45° polarization 67° (half-power) 66° (half-power) 64° (half-power) 66° (half-power) 60° (half-power) 60° (half-power) horizontal beamwidth
+45° and -45° polarization 34° (half-power) 33° (half-power) 30° (half-power) 20° (half-power) 18° (half-power) 17.5° (half-power) vertical beamwidth
Cross polar ratio Main direction 0° 25 dB (typical) 25 dB (typical) 25 dB (typical) 16 dB (typical) 18 dB (typical) 20 dB (typical) Sector ±60° >10 dB >10 dB >10 dB >10 dB >10 dB >10 dB
Kathrein Inc., Scala Division Post Office Box 4580 Medford, OR 97501 (USA) Phone: (541) 779-6500 Fax: (541) 779-3991Email: communications@kathrein.com Internet: www.kathrein-scala.com
All specifications are subject to change without notice. The latest specifications are available at www.kathrein-scala.com.
742 226
65° Dualband Directional Antenna
10.3 inches(262 mm)
22.8 inches(579 mm)
5.5 inches(139 mm)
26.4 inches(670 mm)
Order Information:Model Description
742 226 Antenna with 4 x 7/16 DIN connectors 0° electrical downtilt
24.8 inches(630 mm)
1710/2170-45°
1710/2170+45°
806/960-45°
806/960+45°
Mounting Options:Model Description
2 x 738 546 Mounting Kit for 2 to 4.6 inch (50 to 115 mm) OD mast.
737 978 Tilt Kit for use with the 2 x 738 546 mounting kit 0–34 degrees downtilt angle.
2 x 738 546 Mounting Kit
35 mmM6
64 mmM8
Kathrein Inc., Scala Division Post Office Box 4580 Medford, OR 97501 (USA) Phone: (541) 779-6500 Fax: (541) 779-3991Email: communications@kathrein.com Internet: www.kathrein-scala.com
10640-D 936.2077/h
* Mechanical design is based on environmental conditions as stipulated in EIA-222-F (June 1996) and/or ETS 300 019-1-4 which include the static mechanical load imposed on an antenna by wind at maximum velocity. See the Engineering Section of the catalog for further details.
General specifications:Frequency range 1710–2170 MHz
Impedance 50 ohms
VSWR < 1.5:1
Intermodulation (2x20w) IM3: <-150 dBc
Polarization +45° and -45°
Front-to-back ratio >25 dB (co-polar) >25 dB (total power)
Maximum input power 300 watts per input (at 50°C)
Electrical downtilt 0–8 degrees continuously adjustable (manual or optional remote control)
Connector 4 x 7/16 DIN female
Isolation >30 dB
Cross polar ratio Main direction 0° 25 dB (typical) Sector ±60° >10 dB
Weight 34.2 lb (15.5 kg)
Dimensions 51.3 x 11.8 x 2.7 inches (1304 x 299 x 69 mm)
Equivalent flat plate area 5.48 ft2 (0.509 m2)
Wind survival rating* 120 mph (200 kph)
Shipping dimensions 62.6 x 12.7 x 4.3 inches (1589 x 322 x 108 mm)
Shipping weight 37.5 lb (17 kg)
Mounting Fixed and tilt mount options are available for 2 to 4.6 inch (50 to 115 mm) OD masts.
See reverse for order information.
Specifications: 1710–1880 MHz 1850–1990 MHz 1920–2170 MHzGain 17.5 dBi 17.7 dBi 17.8 dBi
+45° and -45° polarization 66° (half-power) 65° (half-power) 64° (half-power) horizontal beamwidth
+45° and -45° polarization 7° (half-power) 6.7° (half-power) 6.5° (half-power) vertical beamwidth
Sidelobe suppression for first sidelobe 0° 2° 5° 8° T 0° 2° 5° 8° T 0° 2° 5° 8° T above main beam 17 17 15 15 dB 20 20 18 18 dB 20 20 18 16 dB
742 234
65° Panel Antenna
Vertical pattern ±45°- polarization
Horizontal pattern ±45°- polarization
Kathrein panels are antenna products for wireless communications. All ADT panels feature:
• Heavy-duty construction using the highest quality materials: UV resistant pulltruded fiberglass radomes, stainless steel fasteners and hardware, rigid aluminum reflectors, and low loss coaxial cable power divider harness, all contributing to long, trouble free service life.
• Superior electrical specifications including low VSWR, wide bandwidth, flat frequency response, and superb intermodulation performance.
• Precision continuously adjustable electrical downtilt controls, manual control as standard equipment, with remote control available as an option.
• Will accomodate future 3G / UMTS applications.
All specifications are subject to change without notice. The latest specifications are available at www.kathrein-scala.com.
Kathrein Inc., Scala Division Post Office Box 4580 Medford, OR 97501 (USA) Phone: (541) 779-6500 Fax: (541) 779-3991Email: communications@kathrein.com Internet: www.kathrein-scala.com
742 234
65° Panel Antenna
Order Information:Model Description
742 234 Antenna with 7/16 DIN connectors 0°–8° adjustable electrical downtilt
Mounting Options:Model Description
2 x 738 546 Mounting Kit for 2 to 4.6 inch (50 to 115 mm) OD mast.
737 978 Tilt Mount Kit 0–16 degrees downtilt angle.
51.3 inches(1304 mm)
55.9 inches(1421 mm)
54.4 inches(1381 mm)
3.7 inches(83 mm)
2 x 738 546 Mounting Kit
35 mmM6
64 mmM8
2.625 inches ± 0.125(68 mm ± 4)
60 inches(1525 mm)
11.8 inches(299 mm)
Kathrein Inc., Scala Division Post Office Box 4580 Medford, OR 97501 (USA) Phone: (541) 779-6500 Fax: (541) 779-3991Email: communications@kathrein.com Internet: www.kathrein-scala.com
* Mechanical design is based on environmental conditions as stipulated in EIA-222-F (June 1996) and/or ETS 300 019-1-4 which include the static mechanical load imposed on an antenna by wind at maximum velocity. See the Engineering Section of the catalog for further details.
10633-J 936.2700/b
742264
65° Dualband Directional Antenna
Kathrein’s dual band antennas are ready for 3G applications, covering all existing wireless bands as well as all spectrum under consideration for future systems, AMPS, PCS and 3G/UMTS. These cross-polarized antennas offer diversity operation in the same space as a conventional 800 MHz antenna, and are mountable on our compact sector brackets.
• Wide band operation.
• Exceptional intermodulation characteristics.
• Remote control ready.
• Various gain, beamwidth and downtilt ranges.
• AISG compatible.
• High strength pultruded fiberglass radome.
Horizontal pattern±45°- polarization
Vertical pattern±45°- polarization
0°–8° electrical downtilt
Vertical pattern±45°- polarization
0°–14° electrical downtilt
Horizontal pattern±45°- polarization
824–960 MHz
1710–2180 MHz
Generalspecifications:Frequency range 824–960 MHz
1710–2180 MHz
Impedance 50 ohms
VSWR <1.5:1
Intermodulation (2x20w) IM3: -150 dBc
Polarization +45° and -45°
Connector 4 x 7/16 DIN female
Isolation intrasystem >30 dB intersystem >50 dB (824–960 // 1710–2180 MHz)
Weight 36.4 lb (16.5 kg)
Dimensions 51.8 x 10.3 x 5.5 inches (1316 x 262 x 139 mm)
Equivalent flat plate area 4.13 ft2 (0.384 m2)
Wind survival rating* 120 mph (200 kph) sustained 150 mph (240 kph) in a 3 second burst
Shipping dimensions 64 x 11.9 x 7.6 inches (1626 x 302 x 192 mm)
Shipping weight 45 lb (20.4 kg)
Mounting Fixed mount options are available for 2 to 4.6 inch (50 to 115 mm) OD masts.
See reverse for order information.
Specifications: 824–894MHz 870–960MHz 1710–1880MHz 1850–1990MHz 1920–2180MHzGain 14 dBi 14 dBi 16.5 dBi 16.8 dBi 17 dBi
Front-to-back ratio >26 dB (co-polar) >26 dB (co-polar) >25 dB (co-polar) >25 dB (co-polar) >25 dB (co-polar)
Maximum input power per input 400 watts (at 50°C) 400 watts (at 50°C) 250 watts (at 50°C) 250 watts (at 50°C) 250 watts (at 50°C) total power 800 watts (at 50°C) 500 watts (at 50°C)
+45° and -45° polarization 68° (half-power) 65° (half-power) 65° (half-power) 65° (half-power) 63° (half-power) horizontal beamwidth
+45° and -45° polarization 16° (half-power) 14.5° (half-power) 7.8° (half-power) 7.3° (half-power) 6.8° (half-power) vertical beamwidth
Electrical downtilt 0°–14° 0°–14° 0°–8° 0°–8° 0°–8° continuously adjustable
Sidelobe suppression for 0° 7° 14° T 0° 7° 14° T 0° 4° 8° T 0° 4° 8° T 0° 4° 8° T first sidelobe above horizon 14 14 13 dB 14 14 13 dB 14 14 14 dB 16 16 15 dB 15 16 15 dB
Cross polar ratio Main direction 0° 20 dB (typical) 20 dB (typical) 16 dB (typical) 18 dB (typical) 20 dB (typical) Sector ±60° >10 dB >10 dB >10 dB >10 dB >10 dB
Kathrein Inc., Scala Division Post Office Box 4580 Medford, OR 97501 (USA) Phone: (541) 779-6500 Fax: (541) 779-3991Email: communications@kathrein.com Internet: www.kathrein-scala.com
All specifications are subject to change without notice. The latest specifications are available at www.kathrein-scala.com.
MountingOptions:Model Description
2 x 738 546 Mounting Kit for 2 to 4.6 inch (50 to 115 mm) OD mast.
742 033 Three-panel Sector Mounting Kit (120 deg. ea.) for 4.5 inch (114.3 mm mm) OD steel mast.
742 034 Three-panel Sector Mounting Kit (120 deg. ea.) for 5.5 inch (139.7 mm mm) OD steel mast.
737 978 Tilt Mount Kit 0–16 Degrees downtilt angle.
OrderInformation:Model Description
742 264 Antenna with 7/16 DIN connectors
742264
65° Dualband Directional Antenna
10.3 inches(262 mm)
53.8 inches(1367 mm)
51.8 inches(1316 mm)
55.4 inches(1407 mm)
5.5 inches(139 mm)
2.625 inches ± 0.125(68 mm ± 4)
2 x 738 546 Mounting Kit
35 mmM6
64 mmM8
Kathrein Inc., Scala Division Post Office Box 4580 Medford, OR 97501 (USA) Phone: (541) 779-6500 Fax: (541) 779-3991Email: communications@kathrein.com Internet: www.kathrein-scala.com
General specifications: Frequency range 824–960 MHz
1710–2180 MHz
Impedance 50 ohms
VSWR <1.5:1
Intermodulation (2x20w) IM3:< -150 dBc
Polarization +45° and -45°
Connector 4 x 7/16 DIN female
Isolation intrasystem >30 dB intersystem >50 dB (824–960 // 1710–2180 MHz)
Weight 50.7 lb (23 kg)
Dimensions 75.4 x 10.3 x 5.5 inches (1916 x 262 x 139 mm)
Equivalent flat plate area 6.16 ft2 (0.572 m2)
Wind survival rating* 120 mph (200 kph)
Shipping dimensions 87.2 x 11.9 x 7.6 inches (2215 x 302 x 192 mm)
Shipping weight 62 lb (28 kg)
Mounting Fixed mount options are available for 2 to 4.6 inch (50 to 115 mm) OD masts.
See reverse for order information.
* Mechanical design is based on environmental conditions as stipulated in EIA-222-F (June 1996) and/or ETS 300 019-1-4 which include the static mechanical load imposed on an antenna by wind at maximum velocity. See the Engineering Section of the catalog for further details.
10634-I 936.2888/c
742 265
65° Dualband Directional Antenna
Horizontal pattern±45°- polarization
Vertical pattern±45°- polarization
0°–6° electrical downtilt
Vertical pattern±45°- polarization
0.5°–9.5° electrical downtilt
Horizontal pattern±45°- polarization
824–960 MHz
1710–2180 MHz
Kathrein’s dual band antennas are ready for 3G applications, covering all existing wireless bands as well as all spectrum under consideration for future systems, AMPS, PCS and 3G/UMTS. These cross-polarized antennas offer diversity operation in the same space as a conventional 800 MHz antenna, and are mountable on our compact sector brackets.
• Wide band operation.
• Exceptional intermodulation characteristics.
• Remote control ready.
• Various gain, beamwidth and downtilt ranges.
• AISG compatible.
• High strength pultruded fiberglass radome.
Specifications: 824–894 MHz 880–960 MHz 1710–1880 MHz 1850–1990 MHz 1920–2180 MHzGain 15.5 dBi 16 dBi 17.8 dBi 18.2 dBi 18.3 dBi
Front-to-back ratio >27 dB (co-polar) >25 dB (co-polar) >25 dB (co-polar) >25 dB (co-polar) >25 dB (co-polar)
Maximum input power per input 500 watts (at 50°C) 500 watts (at 50°C) 250 watts (at 50°C) 250 watts (at 50°C) 250 watts (at 50°C) total power 1000 watts (at 50°C) 500 watts (at 50°C)
+45° and -45° polarization 68° (half-power) 65° (half-power) 66° (half-power) 65° (half-power) 63° (half-power) horizontal beamwidth
+45° and -45° polarization 10.5° (half-power) 10° (half-power) 5.2° (half-power) 5° (half-power) 4.7° (half-power) vertical beamwidth
Electrical downtilt 0.5°–9.5° 0.5°–9.5° 0°–6° 0°–6° 0°–6° continuously adjustable
Sidelobe suppression for 0° 5° 10° T 0° 5° 10° T 0° 3° 6° T 0° 3° 6° T 0° 3° 6° T first sidelobe above horizon 16 15 15 dB 18 18 16 dB 14 15 17 dB 18 17 17 dB 18 17 17 dB
Cross polar ratio Main direction 0° 20 dB (typical) 20 dB (typical) 16 dB (typical) 18 dB (typical) 18 dB (typical) Sector ±60° >10 dB >10 dB >10 dB >10 dB >10 dB
Kathrein Inc., Scala Division Post Office Box 4580 Medford, OR 97501 (USA) Phone: (541) 779-6500 Fax: (541) 779-3991Email: communications@kathrein.com Internet: www.kathrein-scala.com
All specifications are subject to change without notice. The latest specifications are available at www.kathrein-scala.com.
2.625 inches ± 0.125(68 mm ± 4)
Order Information:Model Description
742 265 Antenna with 7/16 DIN connectors
742 265
65° Dualband Directional Antenna
10.3 inches(262 mm)
77.4 inches(1967 mm)
75.4 inches(1916 mm)
79 inches(2007 mm)
5.5 inches(139 mm)
Mounting Options:Model Description
2 x 738 546 Mounting Kit for 2 to 4.6 inch (50 to 115 mm) OD mast.
742 033 Three-panel Sector Mounting Kit (120 deg. ea.) for 4.5 inch (114.3 mm mm) OD steel mast.
742 034 Three-panel Sector Mounting Kit (120 deg. ea.) for 5.5 inch (139.7 mm mm) OD steel mast.
737 978 Tilt Mount Kit 0–11 Degrees downtilt angle.
2 x 738 546 Mounting Kit
35 mmM6
64 mmM8
742 270Type No.
Triple-band A-PanelDual PolarizationHalf-power Beam WidthAdjust. Electr. Downtiltset by hand or by optional RCU (Remote Control Unit)
936.
2342
/e
S
ubje
ct t
o al
tera
tion.
Input 6 x 7-16 female
Connector position Bottom
Adjustment 3x, Position bottommechanism continuously adjustable
Weight 25 kg
Wind load Frontal: 260 N (at 150 km/h)Lateral: 210 N (at 150 km/h)Rearside: 580 N (at 150 km/h)
Max. wind velocity 200 km/h
Packing size 1819 x 304 x 204 mm
Height/width/depth 1498 / 262 / 149 mm
Mechanical specifications
1920–2170+45°
1710–1880–45°
7-16 7-16
1920–2170–45°
7-16
1710–1880+45°
7-16
806–960–45°
7-16
806–960+45°
7-16
Frequency range
806–866 MHz 824–894 MHz 880–960 MHz 1710–1880 MHz 1920–2170 MHz
Polarization +45°, –45° +45°, –45° +45°, –45° +45°, –45° +45°, –45°
Gain 2 x 14.8 dBi 2 x 15 dBi 2 x 15.2 dBi 2 x 16.5 dBi 2 x 17.2 dBi
Half-power beam width Horizontal: 69° Horizontal: 68° Horizontal: 66° Horizontal: 66° Horizontal: 65°Copolar +45°/ –45° Vertical: 14.3° Vertical: 14° Vertical: 13.3° Vertical: 7.1° Vertical: 6.5°
Electrical tilt 0.5°–12° 0.5°–12° 0.5°–12° 0.5°–8° 0°–8°continuously adjustable
Vertical Pattern – sidelobe 0° ... 6° ... 12° T 0° ... 6° ... 12° T 0° ... 6° ... 12° T 0° ... 4° ... 8° T 0° ... 4° ... 8° Tsuppression for first sidelobe 13 ... 12 ... 10 dB 14 ... 14 ... 14 dB 16 ... 16 ... 16 dB 17 ... 16 ... 15 dB 17 ... 15 ... 13 dBabove main beam
Front-to-back ratio, copolar > 27 dB > 27 dB > 27 dB > 23 dB > 23 dB
Cross polar ratio Typically: Typically: Typically: Typically: Typically:Maindirection 0° 25 dB 25 dB 25 dB 18 dB 20 dBSector ±60° > 10 dB > 10 dB > 10 dB > 10 dB > 10dB
Isolation: Intrasystem > 30 dB > 30 dB > 30 dB > 30 dB > 30 dB
Isolation: Intersystem > 50 dB (806–960 // 1710–1880 MHz)11> 50 dB (806–960 // 1920–2170 MHz)11> 30 dB (1710–1880 // 1920–2170 MHz)
Impedance 50 Ω 50 Ω 50 Ω 50 Ω 50 ΩVSWR < 1.5 < 1.5 < 1.5 < 1.5 < 1.5
Intermodulation IM3 < –150 dBc < –150 dBc < –150 dBc(2 x 43 dBm carrier)
Max. power per input 250 W 200 W 200 W(at 50 °C ambient temperature)
XXXPol A-Panel 806–960/1710–1880/1920–2170 66°/66°/65° 15/16.5/17dBi 0°–12°/0°–8°/0°–8°T
Horizontal Pattern Vertical Pattern0.5°–12° electrical downtilt
10
3
0
66°130°
dB
10
3
0
14°
dB
Horizontal Pattern Vertical Pattern0.5°–8° electrical downtilt
10
3
0
66°125°
dB
+45°/–45° Polarization
7.1°
dB
10
3
0
+45°/–45° Polarization
1710–1880806–960
XX
66°66°
0°–8°
1920–2170
X
65°
0°–8°0°–12°
806–960 1710–1880 1920–2170
806–960
1710–1880
Horizontal Pattern Vertical Pattern0°–8° electrical downtilt
+45°/–45° Polarization
6.5°
dB
10
3
0
1920–2170
65°120°
dB
10
3
0
742 270 Page 1 of 4
KATHREIN-Werke KG . Anton-Kathrein-Straße 1 – 3 . P.O. Box 10 04 44 . 83004 Rosenheim . Germany . Phone +49 8031 184-0 . Fax +49 8031 184-494
Internet: http://www.kathrein.de
Please note: As a result of more stringent legal regulations and judgements regarding product liability, we are obliged to point out certain risks that may arise when products are used under extraordinary operatingconditions.
The mechanical design is based on the environmental conditions as stipulated in ETS 300 019-1-4, whichincludes the static mechanical load imposed on an antenna by wind at maximum velocity.Extraordinary operating conditions, such as heavy icing or exceptional dynamic stress (e.g. strain caused byoscillating support structures), may result in the breakage of an antenna or even cause it to fall to the ground.These facts must be considered during the site planning process.
The installation team must be properly qualified and also be familiar with the relevant national safetyregulations.The details given in our data sheets have to be followed carefully when installing the antennas andaccessories.The limits for the coupling torque of RF-connectors, recommended by the connector manufacturersmust be obeyed.
Any previous datasheet issues have now become invalid.
936.
2342
/e
S
ubje
ct t
o al
tera
tion.
Material: Reflector screen: Weather-proof aluminum.Fiberglass housing: It covers totally the internal antenna components.Fiberglass material guarantees optimum performance with regards tostability, stiffness, UV resistance and painting. The colour of the radomeis light grey.All screws and nuts: Stainless steel.
Grounding: The metal parts of the antenna including the mounting kit and the innerconductors are DC grounded.
Environmental conditions: Kathrein cellular antennas are designed to operate under the environ-mental conditions as described in ETS 300 019-1-4 class 4.1 E. The antennas exceed this standard with regard to the following items:– Low temperature: –55 °C– High temperature (dry): +60 °C
Ice protection: Due to the very sturdy antenna construction and theprotection of the radiating system by the radome, the antenna remainsoperational even under icy conditions.
Environmental tests: Kathrein antennas have passed environmental tests as recommended in ETS 300 019-2-4. The homogenous design of Kathrein’s antennafamilies use identical modules and materials. Extensive tests have beenperformed on typical samples and modules.
The downtilt kit can only be used in combination with the clamps type nos. 738 546, 850 10002, 850 10003.Wall mounting: No additional mounting kit is needed.
Accessories (order separately)
738 546 1 clamp Mast: 50 – 115 mm diameter 1.0 kg 2
850 10002 1 clamp Mast: 110 – 220 mm diameter 2.7 kg 2
850 10003 1 clamp Mast: 210 – 380 mm diameter 4.8 kg 2
733 677 1 clamp Mast: 60 – 115 mm diameter 2.0 kg 2
733 678 1 clamp Mast: 115 – 210 mm diameter 2.6 kg 2
733 679 1 clamp Mast: 210 – 380 mm diameter 4.0 kg 2
733 680 1 clamp Mast: 380 – 521 mm diameter 5.3 kg 2
850 10007 1 downtilt kit Downtilt angle: 0° – 15° 5.9 kg 1
Type No. Description RemarksWeight Units perapprox. antenna
Eurocell A-PanelsThe Advanced Antenna TechnologyFor Cross Polarization
6472
9
1581
1541
1498
Adjustment mechanismwith integrated scale
26214
9Bottom view
–45° +45°RCU
1920–2170806–960
1710–1880
RCURCU
–45° +45°–45° +45°
Page 2 of 4 742 270
KATHREIN-Werke KG . Anton-Kathrein-Straße 1 – 3 . P.O. Box 10 04 44 . 83004 Rosenheim . Germany . Phone +49 8031 184-0 . Fax +49 8031 184-494
Internet: http://www.kathrein.de
936.
2342
/e
S
ubje
ct t
o al
tera
tion.
742 270 Page 3 of 4
KATHREIN-Werke KG . Anton-Kathrein-Straße 1 – 3 . P.O. Box 10 04 44 . 83004 Rosenheim . Germany . Phone +49 8031 184-0 . Fax +49 8031 184-494
Internet: http://www.kathrein.de
Remove the protective cap. Set downtilt angle by rotating theadjustment wheel.
0° – max.°
max.° – 0°
Manual adjustment procedure:
General Instructionsfor Adjustment Mechanism
Description of the adjustment mechanism (protective cap removed):
➀ Adjustment wheel with twist-lockfunction.
➁ Downtilt spindle with integrated scale.
➀ Thread for fixing the protectivecap or the RCU (Remote ControlUnit).
➁ Gearwheel for RCU power drive.
2
12
1
To set the downtilt angle exactly,you must look horizontally at thescale. The lower edge of the gear-wheel must be used for alignment.
Optional: RCU (Remote Control Unit) for remote-controlled downtilt adjustment:
For a description of RCU installation please refer to the respective data sheet.
Screw on the protective cap again.
936.
2342
/e
S
ubje
ct t
o al
tera
tion.
Page 4 of 4 742 270
KATHREIN-Werke KG . Anton-Kathrein-Straße 1 – 3 . P.O. Box 10 04 44 . 83004 Rosenheim . Germany . Phone +49 8031 184-0 . Fax +49 8031 184-494
Internet: http://www.kathrein.de
Please note: Additional weather sealing of correctly installed feederline connector interfaces is not required,nor is it recommended by the connector manufacturers.
General Instructions for Feederline Installation for Triple-band Antennas with Kathrein Installation Set, Type No. 850 10005
Please note: To avoid any damage to the interfaces, please ensure that only suitable tools are used. Totighten the feederline connector interfaces, we strongly recommend using a special Kathrein installation tool(as shown below) in combination with a standard torque-wrench.
1
2
3
4 568 7 9
Description of connector arrangement:
Attachment of the feederline connector and RCU (optional):In order to protect the adjustment mechanism the protective caps have to be attached during feederline installation!
There are six feederline connectors and three adjustment mechanisms located at the bottomof the antenna.
The sequence for installation is:feederline no. 4, 5, 6, 7, 8, 9. Put the connector carefully inplace and hand-screw the nut.
Use a torque-wrench to finishinstallation (see installation tool).
Repeat operations as shown foreach feederline!
After feederline installation, the optional remote control units (RCU)can be mounted if required. For a full description of RCU installationplease refer to the respective data sheet.
Adjustment mechanisms (1 – 3)
Feederline connectors (4 – 9)
Kathrein installation set: Type No. 850 10005Set has to be ordered separately!Set consists of two spanners of 27 and 32 mm width.
These tools are suitable for 7-16 connectors with a wrenchsize of 27 mm or 32 mm.
Tighten nut within a torque range of 25 – 33 Nm dependingon connector manufacturers’ specifications.
27 or 32 mm
1/2″ square actuation according toDIN 3120 Form C
Kathrein Inc., Scala Division Post Office Box 4580 Medford, OR 97501 (USA) Phone: (541) 779-6500 Fax: (541) 779-3991Email: communications@kathrein.com Internet: www.kathrein-scala.com
* Mechanical design is based on environmental conditions as stipulated in EIA-222-G-2 (December 2009) and/or ETS 300 019-1-4 which include the static mechanical load imposed on an antenna by wind at maximum velocity. See the Engineering Section of the catalog for further details.
Horizontal pattern ±45°- polarization
Vertical pattern ±45°- polarization
0°–12° electrical downtilt
General specifications: Frequency range 1710–2690 MHz
VSWR <1.5:1
Impedance 50 ohms
Intermodulation (2x20w) IM3: <-150 dBc
Polarization +45° and -45°
Connector 4 x 7-16 DIN female
Electrical downtilt 0°–12° (continously adjustable) (manual or remote control)
Isolation, between ports >30 dB
Maximum input power 300 watts (at 50°C) per input
Weight 39.7 lb (18 kg) 44.1 lb (20 kg) clamps included
Dimensions 55.7 x 12.7 x 2.8 inches (1415 x 323 x 71 mm)
Wind load at 93 mph (150kph) Front/Side/Rear 162 lbf / 38 lbf / 167 lbf (720 N) / (165 N) / (740 N) Mounting category M (Medium)
Wind survival rating* 120 mph (200 kph)
Shipping dimensions 67.2 x 13.3 x 4.4 inches (1706 x 337 x 112 mm)
Shipping weight 48.5 lb (22 kg)
Mounting Fixed mounts for 2 to 4.6 inch (50 to 115 mm) OD masts are included and tilt options are available.
See reverse for order information.
Kathrein wideband X-polarized antennas are designed for use in PCS, WCS, Wi-Fi, and WiMAX polarization diversity systems.
• X-polarized (+45° and -45°).
• UV resistant pulltruded radomes.
• Wideband vector dipole technology.
• DC Grounded metallic parts for impulse suppression.
1710–2690–45°
1710–2690+45°
7-16 7-16
1710–2690+45°
7-16
1710–2690–45°
7-16
0°
30°
60°
90°
120°
150°180°210°
240°
270°
300°
330° 3
10
20
30
0°
30°
60°
90°
120°
150°180°210°
240°
270°
300°
330° 3
10
20
30
11237-B936.3621/c
800 10622 65° Panel Antenna
Specifications: 1710–1990 MHz 1920–2200 MHz 2200–2490 MHz 2490–2690 MHzGain 0° 6° 12° T 0° 6° 12° T 0° 6° 12° T 0° 6° 12° T 17.4 17.4 17.3 dBi 17.8 17.6 17.5 dBi 18 17.9 17.5 dBi 18 17.7 17.3 dBi
+45° and -45° polarization 65° (half-power) 65° (half-power) 61° (half-power) 61° (half-power) horizontal beamwidth
+45° and -45° polarization 7.1° (half-power) 6.5° (half-power) 5.9° (half-power) 5.7° (half-power) vertical beamwidth
Front-to-back ratio (180°±30°) >25 dB, avg 28 dB >26 dB, avg 28 dB >25 dB, avg 27 dB >25 dB, avg 27 dB
Sidelobe suppression for: 0° 6° 12° T 0° 6° 12° T 0° 6° 12° T 0° 6° 12° T First sidelobe above main beam >18 18 18 dB >18 18 18 dB >18 17 17 dB >18 18 17 d
Cross polar ratio 0° 30 dB (typical) 30 dB (typical) 25 dB (typical) 25 dB (typical) Sector ±60° >10 dB >10 dB >8 dB >10 dB
Kathrein Inc., Scala Division Post Office Box 4580 Medford, OR 97501 (USA) Phone: (541) 779-6500 Fax: (541) 779-3991Email: communications@kathrein.com Internet: www.kathrein-scala.com
All specifications are subject to change without notice. The latest specifications are available at www.kathrein-scala.com.
30
Order Information:Model Description
800 10622 Antenna with 4 x 7-16 DIN connectors
800 10622 65° Panel Antenna
55.7 inches(1415 mm)
59.8 inches(1520 mm)
2.8 inches(71 mm)
58.3 inches(1480 mm)
Mounting Options:Model Description
2 x 738 546 Mounting Kit for 2 to 4.6 inch (included) (50 to 115 mm) OD mast. 4.4 lb (2 kg)
850 10013 Tilt Mount Kit 0–15 degrees downtilt angle. 7.4 lb (3.7 kg)
2.625 inches ± 0.125(68 mm ± 4)
12.7 inches(323 mm)
Bottom view
1710–2690 Left
–45° –45°+45°
Right 1710–2690+45°
RCURCU
Layout of interface
2 x 738 546 Mounting Kit(included)
64 mmM8
Product Data Sheet APX13GV-15DWV-15DWVBR-C
Cellular Triple Band Dual Polarized Antenna, 870-2170, 65 deg, 15.3/17.3/17.6dBi, 2.1m, VET, 2-10deg
Allinformationcontainedinthepresentdatasheetissubjecttoconfirm
ationattim
eofordering
RFS The Clear Choice ® APX13GV-15DWV-15DWVBR-C Rev: A1 Print Date: 14.06.2011Please visit us on the internet at http://www.rfsworld.com/ Radio Frequency Systems
Product DescriptionTriple Band site upgradable for high traffic areas.
Features/Benefits• Easy replacement of existing antennas.• Low profile for low visual impact.• Reduction of site dimensions will ease site acceptance.• No disturbance of each horizontal plane• High front to back ratio• Optional Mechanical Tilt available• Possible retrofit with the remote Electrical tilt system
Technical SpecificationsElectrical Specifications
High Band Vertical Pattern
High Band Horizontal Pattern
Frequency Range, MHz 870-960 1710-1880 1900-2170Horizontal Beamwidth, deg 69 68 61Vertical Beamwidth, deg 8.5 6.5 6Electrical Downtilt, deg 2-10, 2-10, 2-10Gain, dBi (dBd) 15.3 (13.2) 17.3 (15.2) 17.6 (15.5)1st Upper Sidelobe Suppression, dB >17 >15 >15Front-To-Back Ratio, dB >25Polarization Dual pol +/-45°VSWR < 1.5:1Isolation between Ports, dB >30 >30 >303rd Order IMP @ 2 x 43 dBm, dBc >150, >150, N/A7th Order IMP @ 2 x 46 dBm, dBc N/A, N/A, >170Impedance, Ohms 50Maximum Power Input, W 500Lightning Protection Direct GroundConnector Type (6) 7-16 Long Neck Female
Mechanical SpecificationsDimensions - HxWxD, mm (in) 2120 x 270 x 145 (83.46 x 10.63 x 5.71)Weight w/o Mtg Hardware, kg (lb) 27 (59.5)Survival Wind Speed, km/h (mph) 200 (125)Rated Wind Speed, km/h (mph) 160 (100)Max Wind Loading Area, m² (ft²) 0.68 (7.28)Front Thrust @ Rated Wind, N (lbf) 919 (206)Maximum Thrust @ Rated Wind, N (lbf) 919 (206)Wind Load - Side @ Rated Wind, N (lbf) 351 (79)Wind Load - Rear @ Rated Wind, N (lbf) 597 (134)Radome Material PolycarbonateRadome Color Light Grey RAL7035Mounting Hardware Material Diecasted AluminumPacking Dimensions, HxWxD, mm (in) 2315 x 385 x 303 (91.14 x 15.16 x 11.93)
Ordering InformationMounting Hardware APM40-2Mounting Pipe Diameter, mm (in) 60-120 (2.36-4.72)Mounting Hardware Weight, kg (lb) 3.4 (7.5)
Other DocumentationAPM40 Series DatasheetAPM40 Series Installation Instructions
SISTEMI RADIOSIRA
DS 921.510.181/01 Pag.1/1
DIMENSIONS
WEIGHT
WIND SURFACE Front
Side
WIND LOAD Front
(wind speed 150Km/h) Side
ICING PROTECTION
RADOME COLOUR
MOUNTING
PACKING
2033 x 166 x 47 mm
11 Kg
0.34 m2
0.09 m2
362 N
102 N
Full radome
Grey (std.) others on request
On the wall or on pole with pipe
clamps of φ 42 to 114 mm
2160 x 190 x 90 mm
ANTENNA TYPE
FREQUENCY RANGE
IMPEDANCE
CONNECTOR
MAX POWER
VSWR
POLARIZATION
GAIN
HALF POWER BEAMWIDTH
Vertical plane
Horizontal plane
FRONT TO BACK RATIO
ISOLATION
MECHANICAL DOWN TILT
ELECTRICAL DOWN TILT
LIGHTNING PROTECTION
PTEL 19-65/D
1710 ÷ 1880 MHz
50 ohm
2 x 7/16 f
2 x 250 W
≤ 1.5
H / V
2 x 18.5 dBi
5°
65°
≥ 25 dB
≥ 30 dB
Special brackets on request
Standard 0°, 2°, 6°
All metal parts DC grounded
PTEL 19-65/DDUAL POLARIZED FLAT ANTENNA2 x 18.5 dBi - 65° GSM 1800 MHz
ELECTRICAL DATA
All SIRA products are subject to continuous research and development; we thereforereserve the right to alter technical specifications without prior notice.
MECHANICAL DATA
90270
0
180
3 dB
10
90270
0
180
3 dB
10
RADIATION PATTERNS (mid band)
horizontal planevertical plane
Kathrein Inc., Scala Division Post Office Box 4580 Medford, OR 97501 (USA) Phone: (541) 779-6500 Fax: (541) 779-3991Email: communications@kathrein.com Internet: www.kathrein-scala.com
* Mechanical design is based on environmental conditions as stipulated in EIA-222-F (June 1996) and/or ETS 300 019-1-4 which include the static mechanical load imposed on an antenna by wind at maximum velocity. See the Engineering Section of the catalog for further details.
General specifications:Frequency range 1710–2170 MHz
VSWR < 1.5:1
Impedance 50 ohms
Intermodulation (2x20w) IM3: <-150 dBc
Polarization +45° and -45°
Front-to-back ratio >30 dB (co-polar) (180°±30°) >25 dB (total power)
Maximum input power 300 watts per input (at 50°C)
Electrical downtilt 0–6 degrees continuously adjustable
Connector 2 x 7/16 DIN female
Isolation >30 dB
Cross polar ratio Main direction 0° 25 dB (typical) Sector ±60° >10 dB
Weight 22 lb (10 kg)
Dimensions 76.5 x 6.1 x 2.7 inches (1942 x 155 x 69 mm)
Equivalent flat plate area 4.62 ft2 (0.429 m2)
Wind survival rating* 120 mph (200 kph)
Shipping dimensions 87.2 x 6.8 x 3.6 inches (2214 x 172 x 92 mm)
Shipping weight 24.3 lb (11 kg)
Mounting Fixed mount options are available for 2 to 5.7 inch (50 to 145 mm) OD mast..
See reverse for order information.
Specifications: 1710–1880 MHz 1850–1990 MHz 1920–2170 MHzGain 19 dBi 19.2 dBi 19.5 dBi
+45° and -45° polarization 67° (half-power) 65° (half-power) 63° (half-power) horizontal beamwidth
+45° and -45° polarization 4.7° (half-power) 4.5° (half-power) 4.3° (half-power) vertical beamwidth
Vertical Pattern–sidelobe 0° 2° 4° 6° T 0° 2° 4° 6° T 0° 2° 4° 6° T suppression for first side- 18 17 15 15 dB 18 18 17 15 dB 18 18 17 15 dB lobe above main beam
10642-F 936.2074/g
742 213
65° Panel Antenna
Kathrein’s X-polarized adjustable electrical downtilt antennas offer the wireless carrier the ability to tailor polarization diversity sites for optimum performance. Using variable downtilt, only a few models need be procured to accommodate the needs of widely varying conditions. Remotely controlled downtilt is available as a retrofitable option.
• 0-6° downtilt range.
• UV resistant pulltruded fiberglass radome.
• DC Grounded metallic parts for impulse suppression.
• No moving electrical connections.
• Wideband vector dipole technology.
• Optional remote downtilt Control.
• Will accomodate future 3G / UMTS applications.
Vertical pattern ±45°- polarization
Horizontal pattern ±45°- polarization
All specifications are subject to change without notice. The latest specifications are available at www.kathrein-scala.com.
Kathrein Inc., Scala Division Post Office Box 4580 Medford, OR 97501 (USA) Phone: (541) 779-6500 Fax: (541) 779-3991Email: communications@kathrein.com Internet: www.kathrein-scala.com
742 213
65° Panel Antenna
Order Information:Model Description
742 213 Antenna with 7/16 DIN connectors 0°–6° adjustable electrical downtilt
6.1 inches(155 mm)
79.8 inches(2026 mm)
76.5 inches(1942 mm)
2.7 inches(69 mm)
1710–2170-45°
1710–2170+45°
7/16 DIN 7/16 DIN
78.6 inches(1996 mm)
2.625 inches ± 0.125(68 mm ± 4)
2 x 131 1847 Mounting Kit
Mounting Options:Model Description
2 x 131 1847 (shown) Mounting Kit for 2 to 5.7 inch (50 to 145 mm) OD mast.
737 978 Tilt Kit for use with the above mounting kit, 0–11 degrees downtilt angle.
742 263 Three-panel Sector Mounting Kit (120 deg. ea.) for 3.5 inch (89 mm) OD mast.
Recommended