View
0
Download
0
Category
Preview:
Citation preview
MontageanweisungMounting Instructions
Berthold Sichert GmbHKitzingstraße 1 - 5 | D -12277 Berlin
www.Sichert.com
Alle hier enthaltenen Angaben sind nach bestem Wissen richtig und zuverlässig. Sie sind jedoch keine Eigenschaftszusicherung. Der Anwender unserer Produkte muss in eigener Verantwortung über die Eignung für die vorgesehene Anwendung entscheiden. Unsere Produkthaftung richtet sich ausschließlich nach unseren Verkaufs-, Lieferungs- und Zahlungsbedingungen. In keinem Fall sind wir haftbar zu machen für irgendwelche zufälligen, indirekten Schäden oder hieraus resultierenden Folgeschäden jeder Art.All of the above information is believed to be reliable. Users, however, should independently evaluate the suitability of each product for their application. SICHERT makes no warranties as to the accuracy or completeness of the information, and excludes any liability regarding its use. SICHERT’s only obligations are those in the Standard Terms and Conditions of Sale, Delivery and Payment and in no case will SICHERT be liable for any incidental, indirect, or consequential damages arising therefrom.
Telefon | Phone: +49 30 74707-0Telefax | Fax: +49 30 74707-20E-Mail | E-Mail: Info@Sichert.com
Dokument | Document: 70.1270.36.01Revision | Revision: HErsteller | Author: Nee
Nachrüstung oder Ersatz 1. Modul Wärmetauscher SCS (G1, G2)1. Modul LuftaustauscherUpgrade or replacement First module Heat Exchanger SCS (gen 1, gen 2)First module Air Exchanger
für | forSiCab
! Technische Daten und Anschlüsse Klimamodul siehe Datenblatt See data sheet for technical data and connections of climate module
! Montageanweisung Gehäuse beachten Take special note of mounting instructions for cabinet
! Dachmodule mit 2 Kiemenreihen sind zu ersetzen Roof modules with two row ventilation openings have to be replaced
Seite | Page 2 von | of 20
Safety information ■ The device can only be serviced by qualified experts ■ Disconnect the fans before starting maintenance ■ Cut off the heat or air exchanger from the power supply completely (see data sheet) ■ Protect from rain or water ■ Connect only with marked power sources - follow instructions ■ Make sure no foreign objects or liquids get into the housing
Observe the relevant regulations. This instruction manual contains informations to enable the user to work safely and correctly. Only when the manual is understood and adhered to can danger be avoided.
!
SicherheitsvorschriftenNachfolgende Vorschriften und Hinweise sind zu beachten:
■ Unfallverhütungsvorschrift „Grundsätze der Prävention“ (DGUV V1) ■ Unfallverhütungsvorschrift „Elektrische Anlagen“ (DGUV V3) ■ Einhaltung der EU-Richtlinie 2014/35/EU … hier EN 62368-1 ■ Arbeiten an elektrischen Anlagen dürfen nur von dafür ausgebildeten Fachkräften
ausgeführt werden!
Sicherheitsmaßnahmen ■ Sicherstellung, dass bei Inbetriebnahme keine unzulässigen elektromagnetischen
Wirkungen und keine unzulässigen elektromagnetischen Felder entstehen können ■ Es dürfen keine Reinigungsmittel eindringen ■ Unmittelbare Überprüfung aller Sicherheitseinrichtungen,
nach Abschluss der Montagearbeiten ■ Verlegung bzw. Aufhängung aller Zuführungen, so dass…
…der Betrieb der aufgestellten Einheit nicht behindert wird …keine Stolperfallen entstehen …erforderliche Mindestabstände eingehalten werden
Zugelassenes Personal ■ Transport, Aufstellung, Anschluss, Inbetriebnahme, Bedienung und Wartung
darf nur von Fachkräften (nach EN 50110-1 / VDE 0105-100) durchgeführt werden ■ Schäden und Mängel der Einheit sind umgehend von autorisierten Fachkräften zu
beseitigen. Fachkräfte werden vom sicherheitsrechtlich Verantwortlichen des Betreibers für die erforderliche Tätigkeit autorisiert
!Jede Person, die mit der Aufstellung, Inbetriebnahme, Bedienung oder Wartung der Einheit
beauftragt ist, muss die Montageanweisung gelesen und verstanden haben!Observe the relevant regulations. Only authorised personnel are allowed to work on the unit. This instruction manual contains informations to enable the user to work safely and correctly.
Only when the manual is understood and adhered to can danger be avoided.
Sicherheitsbestimmungen Safety standards
Seite | Page 3 von | of 20
Seite | Page
1 Lieferumfang Scope of supply 4 - 6
1.1 Nachrüstsatz SiCab 8 Upgrade kit SiCab 8 4
1.2 Nachrüstsatz SiCab 12 Upgrade kit SiCab 12 5
1.3 Nachrüstsatz SiCab 15, SiCab 18 Upgrade kit SiCab 15, SiCab 18 6
2 Gehäusevorbereitung Preparation of cabinet 7
3 Lage Klimamodul festlegen Set position of climate module 8
4 Dachmodul vorbereiten Preparation of roof module 9 - 14
4.1 Montage Abdeckbleche Mounting cover plates 9
4.2 Montage Zusatz-Abdeckbleche Mounting additional cover plates 10
4.3 Auswahl Schottbleche Selection partitioning plates 11
4.4 Montage Schottbleche Mounting partitioning plates 12
4.5 Lage Schottbleche SiCab 15 Position partitioning plates SiCab 15 13
5 Klimamodul vorbereiten Preparation of climate module 14 - 15
5.1 Dichtbänder aufkleben Fix sealing tape 14
5.2 Erderleitung anschließen und Besonderheiten Luftaustauscher
Connect grounding cableand special features of air exchanger
15
6 Montage Klimamodul Installation of climate module 16 - 18
6.1 Einbau Klimamodul Installation climate module 16
6.2 Einbau Füllplatte Installation filler plate 17
6.3 Erdung Klimamodul und Füllplatte Grounding climate module and filler plate 18
7 Besonderheiten bei Gehäusen mit Schiebetür
Hints for cabinetswith sliding door
19
8 Zubehör, Ersatzteile und Entsorgungshinweis
Accessories, spare parts and disposal advice
20
Inhaltsverzeichnis Contents
1 2 3 Arbeitsschritte Working steps A Variante / Ausführung
Version i Zusatzinformation Additional information
1 Teil (Artikelnummer) Part (Article number)
Umwelthinweise Environmental notes ! Unbedingt beachten
Take care
Zeichenerklärung | Explanation of symbols
Seite | Page 4 von | of 20
Baugruppe | Kit Teile | PartsKlimamodulClimate module
1xIP-SchutzblechIP protector
(In einigen Ausführungen; vormontiertIn some versions; pre-assembled)
Erdung Modul Grounding for module
AbdeckblecheCover plates
2x1xZusatz-Abdeckbleche3
Additional cover plates3
1x 1x 5x (DIN 7981 3.5 x 9.5)
Dichtungen1
Seal kit1
Schottbleche1, 2
Partitioning plates1, 2
2x 2x(105 mm) (93 mm)
BeipackFastener kit 4x (Schnellverschluss | Quick-fit fastener)
1 Lieferumfang Scope of supply1.1 Nachrüstsatz SiCab 8 Upgrade kit SiCab 8
8
1 Anzahl im Set kann abweichen | Number of parts may differ2 Bleche 93 mm nur in einigen Varianten | 93 mm plates in some upgrade kits only3 In einigen Varianten | In some upgrade kits only
(Modul mit Steuerung und Anschlusskabel-SetModule with controller and cable set)
1x
1x (~ 300 mm) 2x (~ 80 mm)4x (~ 180 mm, 2 mm) 4x (~ 180 mm, 6 mm)
9x (DIN 7981 3.5 x 9.5)
4x (DIN 912 M5 + DIN 6797)
1x (Nutenstein / Slot nut)
1x (DIN 9021)
1x (DIN 6797)
1x (DIN 912 M6)
1x (Kabel | Cable)
1x (DIN 6797)
1x (DIN 912 M6)
Seite | Page 5 von | of 20
Baugruppe | Kit Teile | PartsKlimamodulClimate module
(siehe Nachrüstsatz SiCab 8 see upgrade kit SiCab 8)
IP-SchutzblechIP Protector
(siehe Nachrüstsatz SiCab 8 see upgrade kit SiCab 8)
Erdung Modul Grounding for module
(siehe Nachrüstsatz SiCab 8 see upgrade kit SiCab 8)
Füllblech und Erdung Filler plate and grounding
AbdeckblecheCover plates
(siehe Nachrüstsatz SiCab 8 see upgrade kit SiCab 8)
Dichtungen1
Seal kit1
SchottblechePartitioning plates
(siehe Nachrüstsatz SiCab 8 see upgrade kit SiCab 8)
BeipackFastener kit 12x (Schnellverschluss | Quick-fit fastener)
12
1x (Füllblech | Filler plate)
1.2 Nachrüstsatz SiCab 12 Upgrade kit SiCab 12
(vormontiert pre-assembled)
1 Anzahl im Set kann abweichen | Number of parts may differ
3x (~ 300 mm) 2x (~ 80 mm)1x (~ 370 mm)
1x (DIN 912 M6)
1x (DIN 125)
1x (DIN 6797)
1x (DIN 934 M6)
1x (Kabel | Cable)
1x (DIN 9021)
1x (Nutenstein | Slot nut)
1x (DIN 912 M6)
1x (DIN 125)
1x (DIN 6797)
Seite | Page 6 von | of 20
Baugruppe | Kit Teile | PartsKlimamodulClimate module
(siehe Nachrüstsatz SiCab 8 see upgrade kit SiCab 8)
IP-SchutzblechIP protector
(siehe Nachrüstsatz SiCab 8 see upgrade kit SiCab 8)
Erdung Modul Grounding for module
(siehe Nachrüstsatz SiCab 8 see upgrade kit SiCab 8)
Füllblech und Erdung Filler plate and grounding
(siehe Nachrüstsatz SiCab 12 see upgrade kit SiCab 12)
AbdeckblecheCover plates
2x1x 9x (DIN 7981 3.5 x 9.5)
DichtungenSeal kit
(siehe Nachrüstsatz SiCab 12 see upgrade kit SiCab 12)
SchottblechePartitioning plates
(siehe Nachrüstsatz SiCab 8 see upgrade kit SiCab 8)
BeipackFastener kit 16x (Schnellverschluss | Quick-fit fastener)
18
1.3 Nachrüstsatz SiCab 15, SiCab 18 Upgrade kit SiCab 15, SiCab 18
15
Baugruppe | Kit Teile | PartsKlimamodulClimate module
(siehe Nachrüstsatz SiCab 8 see upgrade kit SiCab 8)
IP-SchutzblechIP protector
(siehe Nachrüstsatz SiCab 8 see upgrade kit SiCab 8)
Erdung Modul Grounding for module
(siehe Nachrüstsatz SiCab 8 see upgrade kit SiCab 8)
Füllblech und Erdung Filler plate and grounding
(siehe Nachrüstsatz SiCab 12 see upgrade kit SiCab 12)
Dichtungen1
Seal kit1
BeipackFastener kit 14x (Schnellverschluss | Quick-fit fastener)
4x (~ 300 mm) 2x (~ 80 mm)1x (~ 370 mm)
1 Anzahl im Set kann abweichen | Number of parts may differ
Seite | Page 7 von | of 20
2 Gehäusevorbereitung Preparation of cabinet
8 12 15 18
Dachmodul abhebenRemove roof module
1
2
Bitte beachten Sie die für das Produkt jeweils gültigen Entsorgungsrichtlinien.Please take special note of any regulations regarding the disposal of materials.
Nicht benötigte Komponenten wie altes Klimamodul, Luftleitbleche,Füllplatten, Dichtungen usw. entfernenRemove parts that were not needed (old climate module, cover plates, deflector shields and seals)
3
! Montageanweisung Gehäuse beachten Take special note of mounting instructions for cabinet
A
B
VerriegelungselementeLocking elements
Seite | Page 8 von | of 20
3 Lage Klimamodul festlegen
Set position of climate module
8 12 15 18
8 12 15 18Einbaulage Klimamodul festlegen Specify position of climate module
!Strömungsrichtungen beachten Please note the flow directions
Kaltluft | Warmluft Cold air | Hot air
Warmluftseite
Hot air side
Kaltluftseite
Cold air side
Außenseite
Outer side
Außenseite
Outer side
! Technische Daten und Anschlüsse siehe Datenblatt See data sheet for technical data and connections
Kalt | ColdWarm | Hot
Seite | Page 9 von | of 20
AußenseiteOuter side
= SiCab 8 Kaltluftseite
= SiCab 8 cold air side9xDIN 79813.5 x 9.5
4 Dachmodul vorbereiten Preparation of roof module4.1 Montage Abdeckbleche Mounting cover plates
8 12 15 18
(Falls keine Bleche im Dach vorhanden If not installed in roof)
Außenseite
Outer side
(Unterseite | Bottom)
! Kennzeichenflächen vorneIdentification plates in front
Abbohren falls noch nicht vorhanden (bei eingelegtem Blech)Drill holes if not exist(insert plate before)
Ø 2.5 mm
Seite | Page 10 von | of 20
8 12 15 18
4.2 Montage Zusatz-Abdeckbleche Mounting additional cover plates
(Falls keine Bleche im Dach vorhanden If not installed in roof)
Warmluftseite
Hot air side
Kaltluftseite
Cold air side
KaltluftseiteCold air side
(Unterseite | Bottom)
5xDIN 79813.5 x 9.5
! Kennzeichenflächen vorneIdentification plates in front
Abbohren falls noch nicht vorhanden (bei eingelegtem Blech)Drill holes if not exist(insert plate before)
Ø 2.5 mm
Seite | Page 11 von | of 20
4.3 Auswahl Schottbleche Selection partitioning plates
93 mm
Schottblech WT komplett 3KPartitioning plate WT complete 3KSiNr. | Article number70.1880.30.14
Schottblech WT komplett 4KPartitioning plate WT complete 4KSiNr. | Article number70.1880.30.10
Bei Bedarf einkürzenCut if neccessary
8 12 15 18
105 mm
93 mm
105 mm
Seite | Page 12 von | of 20
4.4 Montage Schottbleche Mounting partitioning plates
8 12 15 18
4xDIN 912M5
AußenseiteOuter side
(SiCab 8: Kaltluftseite)
(SiCab 8: cold air side)
Montagepunkte an AbdeckblechenMounting points on cover plates
SiCab 8
SiCab 12
SiCab 181
2
1
2
Auß
ense
ite |
Out
er s
ide
Seite | Page 13 von | of 20
Außenseite
Outer side
4.5 Lage Schottbleche SiCab 15 Position partitioning plates SiCab 15
8 12 15 18
AußenseiteOuter side
Außenseite
Outer side
Dachmodul 180° drehenTurn roof module 180°
SchottblechPartitioning plate
Seite | Page 14 von | of 20
1x...4x oben | top side
SiCab 8 440 mmSiCab 12 180...190 mmSiCab 15 206 mmSiCab 18 360...370 mm
AußenseiteOuter side
AußenseiteOuter side
(SiCab 8: Kaltluftseite)
(SiCab 8: cold air side)
5 Klimamodul vorbereiten Preparation of climate module5.1 Dichtbänder aufkleben Fix sealing tape
3x
SiCab 15
4x
1x je links und rechts1x Each side left and right
(~ 300 mm)
(~ 80 mm)
(~ 80 mm)
8 12 15 18
1x
! Dichtungen fest andrückenPress seals down firmly
Seite | Page 15 von | of 20
5.2 Erderleitung anschließen und Connect grounding cableBesonderheiten Luftaustauscher and special features of air exchanger
1xDIN 912M6
Unterseite Wärmetauscher SCS Bottom side of Heat Exchanger SCS
Luftleitblech optional entfernbar Removable deflector sheet
Unterseite Luftaustauscher Bottom side of Air Exchanger
Seite | Page 16 von | of 20
6 Montage Klimamodul Mounting climate module6.1 Einbau Klimamodul Installation climate module
8 12 15 18
Außenseite
Outer side
SchnellverschlussQuick-fit
Anzahl (min.) und Einbaulage | Number (min.) and mounting position
SiCab 15
SiCab 8
Auß
ense
iteO
uter
sid
eK
altlu
ftse
iteC
old
air
side
SiCab 18
SiCab 12
Auß
ense
iteO
uter
sid
eA
ußen
seite
Out
er s
ide
4x 8x
7x 8x
Nur SiCab 8: je kurze Seite zentriert an Gerüst klebenSiCab 8 only: stick strips centered on the frame on each side
A
(Schnittdarstellung)(Sectional view)
SchnellverschlussQuick-fit
A
2x (~ 180 mm, 2 mm)2x (~ 180 mm, 6 mm)
Seite | Page 17 von | of 20
6.2 Einbau Füllplatte Installation filler plate
8 12 15 18
Anzahl (min.) und Einbaulage | Number (min.) and mounting position
SiCab 15
SiCab 12
SiCab 18
3
4x
7x
8x
1x (~ 370 mm)
! Fest andrückenFirmly pressing
1
2
Seite | Page 18 von | of 20
6.3 Erdung Klimamodul und Füllplatte
Grounding climate module and filler plate
1xDIN 912M6
Siehe 2. Gehäusevorbereitung Schritt 1 bis 2 in umgekehrter ReihenfolgeSee 2. Remove roof module step 1 up to 2 in reverse order
Dachmodul aufsetzen | Mounting roof module
! Kennzeichenflächen vorneIdentification plates in front
8 12 15 18
Seite | Page 19 von | of 20
7 Besonderheiten bei Gehäusen mit Schiebetür
Hints for cabinetswith sliding door
8 12 15 18(Nur für Gehäuse mit Schiebetür und nachgerüstetem Dachmodul mit 4 Kiemenreihen)(For cabinets with sliding door only and upgraded roof module with four row ventilation openings)
Entnahme Schiebetür Removal of sliding door
! Montageanweisung Gehäuse beachten Take special note of mounting instructions for cabinet
Zwischengelegte VerriegelungsstangeLocking bar between roof module and frame
Dachmodul mit 4 KiemenreihenRoof module with four row ventilation openings
Schiebetür Sliding door
Berthold Sichert GmbHKitzingstraße 1 - 5 | D -12277 Berlin
www.Sichert.com
Alle hier enthaltenen Angaben sind nach bestem Wissen richtig und zuverlässig. Sie sind jedoch keine Eigenschaftszusicherung. Der Anwender unserer Produkte muss in eigener Verantwortung über die Eignung für die vorgesehene Anwendung entscheiden. Unsere Produkthaftung richtet sich ausschließlich nach unseren Verkaufs-, Lieferungs- und Zahlungsbedingungen. In keinem Fall sind wir haftbar zu machen für irgendwelche zufälligen, indirekten Schäden oder hieraus resultierenden Folgeschäden jeder Art.All of the above information is believed to be reliable. Users, however, should independently evaluate the suitability of each product for their application. SICHERT makes no warranties as to the accuracy or completeness of the information, and excludes any liability regarding its use. SICHERT’s only obligations are those in the Standard Terms and Conditions of Sale, Delivery and Payment and in no case will SICHERT be liable for any incidental, indirect, or consequential damages arising therefrom.
Telefon | Phone: +49 30 74707-0Telefax | Fax: +49 30 74707-20E-Mail | E-Mail: Info@Sichert.com
Dokument | Document: 70.1270.36.01Revision | Revision: HErsteller | Author: Nee
8 Zubehör, Ersatzteile und Entsorgungshinweis
Accessories, spare parts and disposal advice
Ersatzmodul oder Nachrüstsatz auf AnfrageClimate module or upgrade kit upon on request
SiNr. | Article number
Abdichtset (z.B. nach Klimamodultausch)Sealing kit (after exchange of climate module)
70.1890.36.00
Nachrüstsatz segmentiertes Füllblech für variable Position Klimamodul (nur SiCab 18)Upgrade kit for variable position of climate module(for SiCab 18 only)
70.1882.35.00
Berthold Sichert GmbH | Kitzingstraße 1 - 5 | D -12277 Berlin
Telefon | Phone: +49 30 74707-0Telefax | Fax: +49 30 74707-20E-Mail | E-Mail: Info@Sichert.com
Bitte beachten Sie die für das Produkt jeweils gültigen Entsorgungsrichtlinien.Please take special note of any regulations regarding the disposal of materials.
Service, Ersatzteilbestellung, ZubehörService, spare part and accessory order
Recommended